7/30/2019 Sf Coating 718-104

1/5

MATERIAL SAFETY DATA SHEETEASTERN COLOR AND CHEMICAL COMPANYINFORMATIONTELEPHONE NO.: 401-331-9010PIGMENT DIVISIONEMERGENCY TELEPHONE NO.: 800-424-930035 LIVINGSTON STREET WEBSITE : www.ecco-lenox.comPROVIDENCE, R.I 02904 EMAIL : www.tech@ecco-lenox.comPRODUCT INFORMATIONSF COATINGHMISSCALECODE :718-104 HEALTH14 = EXTREMEFIRE 03 = HIGHPREPARATION DATE :2/10/04 REACTIVITY02 = MODERATESPECIAL NA1 = SLIGHT 0 = INSIGNIFICANTHAZARDOUS INGREDIENTSCHEMICAL NAMECAS NUMBERWT %LIMITS (mg/m3)NA00PHYSICAL PROPERTIESAppearance :White emulsionOdor :NoneSolubility :DispersiblepH range :8 to 11Viscosity :"9 to 10.5"#6 at 20 rpm(Brookfield)Lbs/Gal :Boiling Point Range (F) :212FVapor Pressure :Is heavier than airEvaporation Rate :Is slower than etherSolid contents (%) :

FIRE AND EXPLOSIVE PROPERTIESFlash Point(F) :NALower Explosive Limit :NAUpper Explosive Limit :NAFIRE FIGHTING INFORMATION

Unusual hazardsNot applicable.

Extinguishing AgentsUse extinguishing media appropriate for surrounding fire.

Personal Protective EquipmentWear self-contained breathing apparatus (pressure-demand MIOSH/OSHAapproved or equivalent) and fullprotective gear.

Page 1

7/30/2019 Sf Coating 718-104

2/5

Product :718-104

REACTIVITY INFORMATION

Instability

This product is stable under normal conditions.

Hazardous Decomposition ProductsNone known.

Hazardous PolymerizationWill not undergo polymerization under normal conditions.

IncompatabilityThere are no known materials which are incompatible with this product.

HEALTH HAZARD INFORMATION

Primary Routes Of EntryInhalation, skin contact, eye contact.

Eye ContactDirect contact with material can cause irritation.

InhalationInhalation of vapor or mist can cause headache, nausea, irritation ofnose, throat and lungs.

Skin ContactProlonged or repeated skin contact can cause slight irritation.

IngestionInduce vomiting and call a physician immediately.

Emergency And First AidIn case of inhalation remove to fresh air.In case of skin contact wash affected skin areas thoroughly with soapand water. Consult Physician if irritationpersists.In case of eye contact flush eyes with a large amount of water for atleast 15 minutes. Consult a physician if irritationpersists.

Page 2

Product :718-104

7/30/2019 Sf Coating 718-104

3/5

SPILL OR LEAK PROCEDURES

Personal ProtectionAppropriate protective equipment must be worn when handling a spill of

this material. See the SAFEHANDLING section for recommendations. If exposed to material duringclean-up operations, see theFIRST AID PROCEDURES section for actions to follow.

General ProceduresKeep spectators away. Floor may be slippery; use care to avoidfalling. Contain spills immediately withinert materials (e.g. sand, earth). Transfer liquids and solid dikingmaterial to suitable containers forrecovery or disposal. CAUTION: Keep spills and cleaning runoff out ofmunicipal sewers and open

bodies of water.

SAFE HANDLING AND USE INFORMATION

Respiratory ProtectionNIOSH/OSHA approved respirator types equipped with anammonia/methylamine cartridge arerecommended.

Eye ProtectionUse chemical splash goggles (ANSI Z87.1 or approved equivalent).

Hand ProtectionWear protective clothing and appropriate impervious gloves. Because avariety of protective gloves exist, consult glove manufacturer todetermine proper type for a specific operation.

VentilationSufficient ventilation, in volume and pattern, should be provided tokeep air contamination below current applicable OSHA permissibleexposure limit or ACGHI's TLV limit. Refer to the current edition ofINDUSTRIAL VENTILATION: A MANUAL OF RECOMMENDED PRACTICE published bythe American Conference of Governmental Industrial Hygienist forinformation on the design, installation, use, and maintenance ofexhaust systems.

Other Protective EquipmentWear safety splash goggles or safety glasses with side shields.Eyewash facility should be readily available.

Page 3Product :718-104

7/30/2019 Sf Coating 718-104

4/5

STORAGE AND DISPOSAL INFORMATIONKeep from freezing; material may coagulate. The minimum recommendedstorage temperature for this material is 45F. The maximum recommended

storage temperature for this material is 120F.

REGULATORY INFORMATIONTOXIC SUBSTANCES CONTROL ACT (TSCA)======================================All components of this product are listed or are excluded fromlistings on the U.S. Toxic SubstancesControl Act (TSCA) Chemical Substance Inventory.CANADIAN DOMESTIC SUBSTANCE LIST (DSL)========================================All components of this product are listed or are excluded fromlistings on the Canadian Domestic

Substance List (DSL) Inventory.

ABBREVIATIONSACGIHAmerican Conference of Governmental Industrial HygienistsBACButyl AcetateCASChemical Abstracts Service Registry NumberCERCLAComprehensive Environmental Response, Compensation, andLiability ActDOTDepartment of TransportationDSLCanadian Domestic Substance ListEINECSEuropean Inventory of Existing ChemicalsNANot ApplicableNFPAThe National Fire AssociationOSHAOccupational Safety and Health AdministrationPELPermissible Exposure LimitRCRAResource Conservation and Recovery ActSARASuperfund Amendments and Reauthorization ActSTELShort term Exposure LimitTLVThreshold Limit valueTSCAToxic Substance Control ActTWATime Weighted AverageVHMISWorkplace Hazardous Materials Information SystemThe information contained herein is, to the best of our knowledge andbelief, accurate. However, sincethe conditions of handling and use are beyond our control, we have no

guarantee of results andassume no liability for damages incurred by use of this material. Itis the responsibility of the user tocomply with all applicable federal, state and local laws andregulations.

Page 4

7/30/2019 Sf Coating 718-104

5/5

ECCO SF COATING 718-104

Description: ECCO SF COATING 718-104 a VOC free waterbornepolyurethane based soft-feel coating.

PHYSICAL PROPERTIES:

Appearance - off-white, low viscosity liquid

PH - 8.0-11.0

Viscosity, cps@25C - 80-200

Density lbs./gal. - 8.70

USES & BENEFITS:

ECCO SF COATING718-104 is a VOC free, waterborne polyurethane basedsoft-feel coating for paper, vinyl, textiles, metal and othersubstrates.

ECCO SF COATING 718-104 provides:

Flat, soft feel

No mark-off

No change appearance when heat embossed.

APPLICATION:

ECCO SF COATING 718-104 apply full strength or reduce with water todesired solids or viscosity, by spray, gravure, roller coater, knife

over roll and other methods.