Setup and User’s Manual TSHARC “C-Ray” Capacitive Touch Screen … · 2017. 9. 12. · touch...

M:\03_Products\TSHARC_Boards\TSHARC_C-Ray\C_Ray_3.3A\C-Ray_3.3_UsersManual\08B_TSHARC_C-Ray_Users_Rev3.3x_081121.doc

Setup and User’s Manual TSHARC “C-Ray” Capacitive

Touch Screen Controller Board (RS-232 and USB)

Version 3.3x

Document Revision and Copyright Document Name: 08B_TSHARC_C-Ray_Users_Rev3.3x_081121.doc Document Date: November 21, 2008 Copyright Hampshire Company, Inc. 1995 – 2008 All rights reserved Hampshire® TSHARC™ and UniWInDriver™ are the exclusive trademarks of Hampshire Company, Inc. Elo and 3M (Microtouch) are trade names of Tyco Electronics and 3M Company respectively. All Rights Reserved. Contact Information Hampshire Company, Inc. 9055 N. 51st Street, Suite H Brown Deer, WI 53223 www.hampshirecompany.com Phone: 414-355-4675 Fax: 414-355-4775

Review Display Systems 01959 563 345

2

Table of Contents IMPORTANT DOCUMENT AND USER INFORMATION .............................................................................................. 3 GENERAL INFORMATION ........................................................................................................................................... 3

MAILING ADDRESS: ......................................................................................................................................................... 3 WORLD WIDE WEB: ....................................................................................................................................................... 3 SUPPORT E-MAIL ADDRESS ............................................................................................................................................ 3 COPYRIGHT INFORMATION ............................................................................................................................................... 3 EDITION INFORMATION .................................................................................................................................................... 3

PRODUCT DESCRIPTION ............................................................................................................................................ 4 PART NUMBER INFORMATION .......................................................................................................................................... 4

INTEGRATING THE TSHARC CAPACITIVE CONTROLLER ...................................................................................... 4 MOUNTING THE CONTROLLER .......................................................................................................................................... 4

Figure 4.0: Controller Mounting Diagram .................................................................................................................. 4 MOUNTING THE CAPACITIVE TOUCH SCREEN .................................................................................................................... 5 CONNECTING THE TOUCH SCREEN................................................................................................................................... 5

Figure 5.0: Touch Screen Connection Diagram ....................................................................................................... 5 COMMUNICATION JUMPER CONFIGURATIONS ...................................................................................................... 6

Figure 6.0: Jumper Selectable Communications ...................................................................................................... 6 CONNECTING THE C-RAY FOR RS-232 COMMUNICATION ................................................................................................... 6

Figure 6.1: RS-232 Cable Connection Diagram ....................................................................................................... 6 CONNECTING THE C-RAY FOR USB COMMUNICATIONS ...................................................................................................... 7

Figure 7.0: USB Cable Connection Diagram ............................................................................................................ 7 ADDITIONAL CONNECTION INFORMATION .......................................................................................................................... 7

COMMUNICATION PROTOCOL ................................................................................................................................... 8 Table 8.0: Hampshire standard USB Protocol .......................................................................................................... 8 Table 8.1: Hampshire standard RS-232 Protocol ..................................................................................................... 8

POWERING YOUR SYSTEM ........................................................................................................................................ 8 STATIC PROTECTION WARNING ....................................................................................................................................... 8 STATUS LED INDICATOR ................................................................................................................................................. 8

SOFTWARE DEVICE DRIVERS ................................................................................................................................... 9 SAVING CALIBRATION TO EEPROM ................................................................................................................................ 9

HAMPSHIRE SUPPORT SERVICES ............................................................................................................................ 9 APPENDIX ................................................................................................................................................................... 10

PRODUCT SPECIFICATIONS ........................................................................................................................................... 10 MECHANICAL DIAGRAM ................................................................................................................................................. 10

Figure 10.0: Mechanical Diagram of TSHARC C-Ray Touch Screen Controller Board .......................................... 10 QUICK VIEW SETUP ...................................................................................................................................................... 11

Figure 11.0: Quick View Setup Diagram ................................................................................................................ 11 CABLES AVAILABLE FROM HAMPSHIRE ........................................................................................................................... 12

Table 12.0: Available Communication Cables ........................................................................................................ 12 Table 12.1: Available Power Cables ....................................................................................................................... 12

NOTES ......................................................................................................................................................................... 13


3

IMPORTANT DOCUMENT AND USER INFORMATION This document is to be used as a guide only. The information contained in this document is subject to change without notice. This document and all of its contents are protected under US and international copyright law. Hampshire Company trademarks, patents and copyrights are the exclusive property of Hampshire Company, Inc. and may not be used without the express written consent of Hampshire Company, Inc. Due to the vast range of application variables that fall outside of Hampshire’s expertise and control, Hampshire assumes no responsibility for the usability or the suitability of Hampshire products in customer application(s). Hampshire assumes those responsible for the application and use of Hampshire Company products and documentation have taken all necessary steps to insure that the application of Hampshire products meet any and all safety and performance requirements including any laws, regulations, codes and standards associated with the application. In no case does Hampshire warrant the usability or suitability of its products in any medical, aviation, military or other life critical applications. User should contact Hampshire Company before integrating any Hampshire hardware or software product into these types of applications. All Hampshire standard software products, including but not limited to device driver software, are provided “as is” and may be used exclusively with an authentic Hampshire TSHARC touch screen controller. Hampshire does not warrantee or guarantee the usability of any of its software products. Hampshire Company warrants to the original purchaser, or a third party who is listed on the Hampshire “Multi Party Authorization Agreement”, that for the warranty period identified by Hampshire warranty for the specific product that you have purchased, that the goods will be in conformance with Hampshire specifications. In addition to Hampshire specifications, the warrantee includes Non-Hampshire specifications agreed-to, in writing, by Hampshire in advance for the limited purpose between the customer and Hampshire Company. The warrantee also insures that the goods will be free from defects in design and material for the warrantee period. Hampshire Company, at its option, will repair or replace the nonconforming or defective goods, issue a credit memorandum, or refund the purchase price, as its sole obligation: provided that the nonconforming or defective goods are rejected in writing (including a reasonable failure analysis statement) to Hampshire Company and returned to Hampshire Company within the relevant warranty period and provided that the nonconformance or defect was not caused by misuse, alteration, accident, or abnormal conditions of storage, operation or handling, as determined by Hampshire Company. THIS WARRANTY IS YOUR SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, FURTHER, HAMPSHIRE COMPANY SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGE OR LOSSES, INCLUDING LOSS OF PROFITS, BUSINESS INTERRUPTION, OR OTHER PECUNIARY LOSS, WHETHER ARISING FROM BREACH OF WARRANTY OR BASED ON CONTRACT, FUNDAMENTAL BREACH OR ANY OTHER THEORY. SINCE SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS OF THE TERMS OF ANY IMPLIED WARRANTY, OR EXCLUSION OR LIMITATION OF INCIDENTAL OF CONSEQUENTIAL DAMAGES, THE LIMITATIONS AND EXCLUSIONS OF THIS WARRANTY MAY NOT APPLY TO YOU. General Information Mailing address: World Wide Web: Support E-Mail Address Hampshire Company, Inc. 9055 North 51st Street Suite H Brown Deer, WI 53223 Phone: 414-355-4675 Fax: 414-355-4775

www.hampshirecompany,com

[email protected]

Copyright Information This manual is ©1995-2008 Hampshire Company, Inc. Reproduction of the contents of this copyrighted material in whole or in part, by any means, mechanically or electronic, for any purpose, without the written permission of Hampshire Company, Inc. is prohibited.

Hampshire Company, Inc., the Hampshire Logo, Hampshire®, TSHARC™, the TSHARC logo, and UniWinDriver™ are Trademarks of Hampshire Company, Inc. Elo and 3M (Microtouch) are trade names of Tyco Electronics and 3M Company respectively. All Rights Reserved.

Edition Information Printed on: November 21, 2008 Document Part number: 08B_TSHARC_C-Ray_Users_Rev3.3x_081121.doc


4

Product Description The TSHARC C-Ray Board is a new standard in capacitive touch screen controller technology. It supports serial and USB communication as well as all manufacturers’ capacitive touch screens regardless of whether or not the screen includes a back shield. The C-Ray is a high-performance touch screen controller which, in holding true to Hampshire’s design fundamentals, utilizes ‘off-the-shelf’ microcontroller technology in conjunction with Hampshire’s proprietary decoding techniques and device driver software. This virtually eliminates the threat of obsolescence while maintaining the high-performance and utility standards expected from Hampshire Company. Hampshire’s own TSHARC device drivers are included with the chip or board solutions. Bill-Of-Materials schematic drawings and technical support are available for chip applications. Custom and private-labeled hardware and software products are also available.

Part Number Information HS12-009C0J-03

The latest firmware revision will be supplied with all TSHARC C-Ray capacitive boards ordered. Integrating the TSHARC Capacitive Controller Mounting the Controller The controller has two .122” diameter (4-40 or 3mm screw) plated mounting holes. Notice the mounting hole closest to the touch screen connector H4. THIS STATIC GROUND MOUNT MUST TERMINATE TO A STATIC GROUND. Failure to ground the controller will result in poor performance and may eliminate the effectiveness of the on board static protection. Please refer to Fig. 4.0 for mounting details. For additional details about controller integration, please contact Hampshire. For best performance mount the controller: 1) In such a way to keep the touch screen tail away from high EMI, RFI and power sources. 2) “In line” with the touch screen tail limiting the number and severity of any bends or folds in the touch screen

tail. Contact your touch screen manufacturer to determine any touch screen manufacturer’s mounting specifications.

3) In a way to insure that you are using a communication cable with adequate shielding which is located away from high EMI, RFI radiating system components.

4) To shield the controller and/or the touch screen from EMI / RFI noise in cases where required. Mounting the controller into a metal box which is shielded might be necessary.

5) To insure the back shielded touch screen terminates to pin #3 (center pin) of H4. It is required if a back shield is available.

6) Make sure the back shield of the sensor does not come in contact with any grounded part of the system. IF PIN #3 IS CONNECTED IN ANY WAY TO AN EXTERNAL GROUND, YOU MAY PERMANENTLY DAMAGE YOUR CONTROLLER BOARD.

7) Such that the board, the LCD, and the computer system all have the same ground. Failure to have the same ground throughout the system may result in reduced controller performance.

8) The static ground mount must be terminated to a static ground before powering on the controller board. Failure to follow this procedure will bypass the static protection and may damage the controller causing the board to not function properly.

Figure 4.0: Controller Mounting Diagram

HAMPSHIREHSC2009SIJC2S4B0726

+

H1

H2

H3

H2-A

H1-A

Mounting Holes2 plcs. .122" dia 4-40 screw (3mm)

Required STATIC ground mount.122" Dia. 4-40 (3mm)


5

Mounting the Capacitive Touch Screen There are a number of methods that may be used to mount your touch screen depending upon your application and the recommendations of your sensor supplier. In all cases it is important that you do not make any electrical connections between the touch sensor and the integrated system. Please contact your sensor manufacturer for specific mounting recommendations. The sensor tail often experiences more electrical noise than the sensor itself. Special care should be taken when considering the tail mounting of the sensor. Please contact your sensor manufacturer for specific instructions regarding the sensor tail. In all cases, take special care to mount the touch screen in such a manner as to eliminate any screen shift or movement during operation. The C-Ray controller gathers environmental variables at power-up. Any changes to the touch screen position during use can negatively influence the performance of the system.

Connecting the Touch Screen The TSHARC C-Ray, capacitive controller supports back shielded, non-back shielded and shielded tail capacitive touch screen overlays. Check the touch screen tail and verify the pin-out of the touch screen before you connect the touch screen to the controller. If the touch screen has a back shield or a shielded tail a connection must be made to the 3rd pin of header H4. Failure to connect a shielded touch screen or tail will cause the controller to malfunction. This connection is shown in Fig. 5.0. Note: Hampshire’s touch screen mapping is consistent with all operating system display mapping specifications. Most operating systems draw the screen from upper left to lower right. If you are using the controller in a 3M® (Microtouch™ 5 - Byte emulation) mode, the touch screen connection may not be consistent with this mapping protocol. In some cases, 3M™ maps the screen from lower left to upper right which is 180 degrees rotated from Microsoft standard. For 5-byte Emulation mode the touch screen connection will be as follows: UL, UR, Shield, LR, LL. Contact Hampshire for pin-out compatibility solutions. NOTE: Hampshire does not recommend that you use the controller in a Microtouch™ emulation mode on any forward moving products. This tool is designed to be used for migrating from Microtouch™ to Hampshire™ standard products. !! Hampshire device driver software will correct for Microtouch™ touch screen orientation via the TSHARC calibration software. There is no need to change the Microtouch™ touch screen connections in order to use the Hampshire’s native controller configuration with a Hampshire driver. If you have developed your own driver or are using raw data from the controller you must connect the touch screen to the controller as identified below.

Figure 5.0: Touch Screen Connection Diagram

Capacitive Touch Screen

TopRightTopLeftBack ShieldLowLeftLowRight

If no back shield consctruction do notconnect center "back shield" connection.

Touch Screen Connection Diagram


+

H1

H2

H3

H2-A

H1-A



6

Communication Jumper Configurations The TSHARC Capacitive controller supports RS-232 and USB, HID compliant, low speed, communication. While these are Hampshire’s standard communication formats, custom communications are available. Please refer to Fig. 6.0 for the jumper configurations that may be implemented.

Figure 6.0: Jumper Selectable Communications


+

H1

H2

H3

H2-A

H1-A

2.185"

1

+ Pw

r -

J1POWERGROUND

Mounting Hole, One of Two .122" dia. 4-40 (3mm)

Mounting Hole, One of Two .122" dia. 4-40 (3mm)

Hampshire StandardHS12-049COJ-03

USB RS-232

Connecting the C-Ray for RS-232 Communication Before connecting the RS-232 communication cable, check the jumper setting on the board to insure that it is set properly for RS-232 communication.

Figure 6.1: RS-232 Cable Connection Diagram

3 - Txd2 - Rxd

PwrGnd

CommunicationHeader

+5vDC or 7.5 - 24vDC

5 - Gnd

1

5

6

9

Txd transmit to boardRxd transmit from board

Jumper as shown is set for Hampshire RS-232 Remove for USB operation

USB

+ Pw

r -

H2

1



H1

H2

H3

H2-A

H1-A

Mounting Holes2 plcs. .122" dia 4-40 screw (3mm)

+

.

The RS-232 communication cable can be connected to the controller using a variety of cable types. Part number C72-100S2F-09XDXF cable may be sourced directly from Hampshire Company. This is a standard 6’ long DB-9 female connector terminated to a (housing/contact) 10 position dual row socket via a round shielded cable. This cable has a ground shield termination wire running the length of the cable which must be terminated to earth ground. Not terminating the cable shield will have a negative effect on the controller’s performance. Should a self-built cable be required, a 10-position, dual-row socket contact/housing connector type may be used to connect the RS-232 communication header. If an IDC connector type is desired, a 14-position socket can be used, which extends on to the USB pins with only the RS-232 communication connections terminated. A 10-position IDC socket cannot be used for connecting to the communication header because the width of an IDC socket is too wide to fit between the USB connection pins and the pins needed for RS-232 communication. Hampshire also provides the option to use a single row, 2.0 mm, 7-pin connection to the serial communication connection of the TSHARC-C controller board. This option may be used if it is desired to continue to connect the TSHARC-C controller to your system which has already been configured for 3M™ Microtouch™ connections. Please contact Hampshire for ordering instructions regarding this option.


7

Connecting the C-Ray for USB Communications Take special care when connecting the USB cable. Incorrect pin selection using the USB cable will result in a failed board when attempting to power the board. Also, be sure the jumpers are configured the way required for USB performance. Connect the USB header contacts as shown in Fig. 7.0 for enabling USB communications with the controller board. The USB contacts are located on the lower side of the communication header. A 6’ long 4-position socket to a Type “A” USB plug jacketed and shielded USB cable, part number C72-040S1F-04XAXM from Hampshire Company, Inc can be ordered. This particular cable has a ground shield termination wire running the length of the cable which must be terminated to earth ground. Not terminating the cable shield will have a negative effect on the controller’s performance. For information about ordering this cable, please contact Hampshire Company, Inc.

Special Note: If planning to use a USB-hub, then it is critical to use a hub which has externally supplied power. If multiple devices are attached to the hub, then be sure the hub has sufficient power to power all devices connected. Failure to follow this recommendation will cause the controller to fail during operation.

Figure 7.0: USB Cable Connection Diagram


H1

H2

H3

H2-A

H1-A

USB Communication Header Ground contacts 2-pls allows for polorization of 5pos USB connector

Do not connect power pin on USB if connecting external power on H2

Pinout4321

PinOut1 (Gnd)2 (D+)3 (D-)4 (Pwr)

Do not place jumper for USB communication

+


There is an extra ground pin for USB which may be used to connect a five position USB connector. A five pin connection may be required if polarization of the connector is desired to insure it is terminated correctly.

Additional Connection Information Communication Connector UL and part number information can also be found in Fig. 10.0. Touch Screen: Amp 103635-4 Communication: .100” Sullins: PEC05DBAN & PEC02SBAN Mounting Hardware Due to the wide variety of mounting options available for the TSHARC capacitive board, we do not stock mounting hardware. Please visit the RAF web site to review the available mounting hardware. http://www.rafhdwe.com/RAF_site/OnlineCatalog/EHCoverFrame.html TSHARC Controller Chip Solutions Large volume OEM’s who have in-house electrical and software engineers on staff may purchase a Hampshire “Chip Only” touch screen controller solution which may be integrated on to their main board. A complete set of technical documentation is available from Hampshire Company to assist in correctly integrating a chip solution into a product. Please contact Hampshire Company, Inc. for additional information.


8

Communication Protocol All Hampshire touch screen controllers communicate with the host computer in a 4-byte communication protocol. Hampshire’s 4-byte communication protocol produces the industry’s most reliable and accurate data transfer information without compromising touch speed. Note: Many Hampshire controllers may be configured to communicate with other industry protocols such as 3M’s 5-Byte or Elotouch™ 10-byte communication protocol. However, the overall performance of the Hampshire controller will then be limited to that standard’s level of performance. In no case does Hampshire authorize the use of any driver software, other than Hampshire device drivers or a Windows HID driver, to enable a Hampshire controller without proper authorization from the software developer or rightful owner of the software. For information regarding Hampshire’s 3M or Elo migration hardware or software communication protocol, please contact Hampshire Company, Inc. Elo and 3M (Microtouch) are trade names of Tyco Electronics and 3M Company respectively. All Rights Reserved.

Table 8.0: Hampshire standard USB Protocol Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 0 0 0 0 0 0 0 P 2 X7 X6 X5 X4 X3 X2 X1 X0 3 0 0 0 0 X11 X10 X9 X8 4 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0 5 0 0 0 0 Y11 Y10 Y9 Y8

Table 8.1: Hampshire standard RS-232 Protocol Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 1 P X11 X10 X9 Y11 Y10 Y9 2 0 X8 X7 X6 X5 X4 X3 X2 3 0 Y8 Y7 Y6 Y5 Y4 Y3 Y2 4 0 0 0 0 X1 X0 Y1 Y0 Where: P - 0 Pen-Up, 1 Pen-Down X11-X0 - 12 bit X position data Y11-Y0 - 12 bit Y position data

Powering Your System Before applying power to your system, please check all cables are tightly connected and verify the mounting of the controller and sensor. If powering the controller using USB, the system power should be brought up at the same time. If using an external power supply, please be certain that the monitor is activated before the controller is turned on. The environmental baseline is taken at power-up, and performance could be affected if the monitor is not present when the controller is powered on.

Static Protection Warning The TSHARC C-Ray controller has internal static protection to +/- 30kV for static discharge from the touch screen to the controller. This static protection is only effective once the board is grounded properly. Adequate static precautions must be taken when connecting the TSHARC controller to the application. In some applications, it may be necessary to further protect your controller board from excess transient voltage. If it is believed that the application will require additional static protection, the appropriate static protection needed to protect the electronics from transient voltage is up to the customer. Failure to take the necessary precautions may result in damage to your controller. Hampshire does not warrantee the board for static voltage damage. For additional information about Hampshire’s ESD testing procedures, please contact Hampshire Company. Email: [email protected] Telephone: (414) 355-4675

Status LED Indicator The TSHARC C-Ray capacitive touch screen controller board is equipped with a status-indicator Light Emitting Diode (LED). This LED will give you information regarding the functionality of the controller. The LED indication codes are as follows:

When powered on: The LED with blink once (on then off), collect an environment baseline then blink once again for 1 second. DO NOT TOUCH THE TOUCH SCREEN DURING THIS PROCESS. Every time the touch screen is touched: Once the controller has collected the baseline, the LED will turn off. It will turn on every time the operator touches the touch screen thereafter.

DO NOT TOUCH THE TOUCH SCREEN IMMEDIATELY AFTER THE CONTROLLER IS POWERED ON. THE CONTROLLER MUST COMPLETE THE BASELINE PROCESS IN ORDER TO POWER ON CORRECTLY.


9

Software Device Drivers Hampshire Company has device driver software available for all TSHARC touch screen controller chip and board solutions. The software drivers may be downloaded at no additional charge at: www.hampshirecompany.com . Reported Hampshire resolution is dependent upon the hardware A-D converter specification. Hampshire device driver software is designed to deliver true 10 or 12 bit hardware resolution respective to the touch screen controller hardware. The TSHARC device driver software enables you to configure the touch screen operation to meet your needs. The following is a list of features available with Hampshire’s software:

1) Touch screen calibration 2) Touch screen linearization 3) Touch screen alignment 4) Multi-monitor calibration and configuration 5) Adjustable calibration inset 6) Edge acceleration 7) Touch modes

a. Normal mouse emulation b. Touch Up mode c. Touch Down mode

8) User adjustable Configurations a. Hampshire proprietary touch screen friendly timed right click event b. Touch event area setting c. Touch sound enable / disable

9) Other special features also included. Please see the complete driver manuals available at the www.hampshirecompany.com web site for further details.

Note: TSHARC device drivers vary between operating systems and operating system varieties and versions. Currently Hampshire supports the following Windows® Operating systems: DOS, Win3.1x, 9x, ME, Xp, XPe, 2k, CE, CENet, Tablet. TSHARC driver for Linux, and MAC are also included with all TSHARC touch screen controller products. Additional utilities may be available for use. Please contact Hampshire Company for additional information.

Saving Calibration to EEPROM The firmware included on this board is able to store calibration data to the controller’s EEPROM. Additional utilities are available to utilize this feature. Please contact Hampshire Company for additional information.

Hampshire Support Services All of Hampshire products are 100% developed and supported in house by Hampshire technical staff. As a result, we have included a broad range of support documentation on the Hampshire web site www.hampshirecompany.com including users and setup manuals, device drivers, driver manuals, and other software. In addition, we have an e-mail based support. Please contact us via e-mail at: [email protected]. Hampshire also understands that there is often a need for “real time” technical support. Please contact Hampshire via telephone at any point to discuss issues that you may have regarding our products. Hampshire’s telephone number: 414-355-4675. In the event that you need to contact us via telephone or our support e-mail, please take a moment to complete our “On Line” support form which is available on our web site: www.hampshirecompany.com. Completing this form prior to contacting Hampshire will insure a prompt response from our technical staff. If the on-line form is not completed, our technical staff will ask you for the following details of the application. Please take a minute to identify these items prior to contacting Hampshire technical support staff. 1) Hampshire controller part number 2) Information about Hampshire reseller if not purchased directly from Hampshire 3) Hampshire chip revision (located on the top of each micro-controller chip) 4) Touch Screen type and Manufacturer 5) Communication type 6) TSHARC driver and revision 7) Operating system and service pack releases 8) A brief summary of the problem experienced.


10

Appendix

Product Specifications

Touch Screen: Resolution:

Communications: Com Protocol:

Size:

Connectors Touch Screen Side:

Com Side:

Sample Rate: Baud Rate:

Voltage Required: Environmental:

Static Protection: PC Board UL File:

Connectors UL File: Part Number:

All Capacitive touch screens with or w/o back shield 12 Bit (4,096 x 4,096) RS-232 and USB HID Compliant USB and Hampshire Standard serial 2.43” x 1.30” Amp 103635-4 .100” Sullins: PEC05DBAN & PEC02SBAN Configurable 40 - 100 points/sec. (raw data >240 points/sec.) 9600 baud (others available upon request) 5Vdc– 16Vdc +/- 5% or from USB port Storage: -65°C – 150°C Operating: -40°C – 70°c 30 KVA See Fig. 5.0 See Fig. 5.0 HS12-009C0J-03

Mechanical Diagram

Figure 10.0: Mechanical Diagram of TSHARC C-Ray Touch Screen Controller Board HAMPSHIREHSC2009SIJC2S4B0726

+

.165

"

.165

"

.175

".3

43"

.100"

.100"

1.30

0"1.

175"

.350

".0

50"

.450

".1

25"

Mount holes 2 places.122" Dia. 4-40 or 3mm screw.

.125"

2.310"

H1

H2

H3

H2-A

H1-A

.160"

2.010"2.435"

REQUIRED STATIC ground mount .122" Dia. 4-40 (3mm)

ConnectorSullins: PEC02SBANUL# E64287

ConnectorSullins: PEC02SBANUL# E64287

ConnectorSullins: PEC05DBANUL# E64287

UL# E28476

.100" ConnectorAMP: 103635-4UL# E28476

NOTE!! The board revision number can be found on a label on the back side of your controller board. The firmware revision number may be found on a label or a laser mark located on the TSHARC microcontroller chip.


11

HA

MP

SH

IRE

HS

C2

00

9S

IJC

2S

4B

07

26

+

H1 H2H3

H2

-A

H1

-A

H3

Ham

pshi

re S

tand

ard

HS1

2-00

9CO

J-03

USB

RS-

232

Ham

pshi

re C

omm

unic

atio

n C

able

RS

-232

Cab

le:

C72

-100

S2F

-09X

DX

FU

SB

Cab

le:

C72

-040

S1F

-04X

AX

M

ST

EP 3

Conn

ect T

ouch

Scre

en

2 - R

xd3

- TX

5 - G

nd

15

69

Step

4Co

nnec

t Com

mun

icatio

n Ca

ble.

If us

ing

exte

rnal

pow

er a

t pos

itions

H2

for U

SB,

DO N

OT

CONN

ECT

the

USB

powe

r pin

#8

(+5v

DC) St

ep 5

Conn

ect P

ower

Top

right

Top

Left

Bac

k S

hiel

dB

otto

m L

eft

Bot

tom

Rig

ht

Follo

w th

ese

step

s:1)

Set

Com

mun

icat

ion

type

2) M

ount

Con

trolle

r3)

Con

nect

Tou

ch S

cree

n4)

Con

nect

Com

mun

icat

ion

Cab

le

5) C

onne

ct P

ower

6) T

urn

on C

ompu

ter

7) In

stal

l TS

HA

RC

driv

ers

Step

2Mo

unt C

ontro

ller

Use a

jack

eted -

shiel

ded

touch

scre

en ca

ble fo

r be

st pe

rform

ance

Gnd

D+

D-

+5vD

C

Gnd

D+

D-

+5vD

C13 24RS

-232

Gnd

Gnd D+

+5vD

CD-U

SB

RxdTXGnd

Pow

erG

roun

d

Ste

p 1

Set C

omm

unica

tion

Ty

pe

Re

qu

ire

d S

TAT

IC g

rou

nd

mo

un

t.1

22

" D

ia. 4

-40

(3

mm

)

ww

w.h

amps

hire

com

pany

.com

Pho

ne:

414-

355-

4675

Fax

: 41

4-35

5-47

7590

55 N

51s

t S

tree

t S

uite

: H

Ham

pshi

re C

ompa

ny,

Inc.

Bro

wn

Dee

r,

WI

532

23

US

AHam

pshi

re T

SH

AR

CTM

C-R

ay Q

uick

Vie

w K

it A

ssem

bly

Dia

gram

HA

MP

SH

IRH

AM

PS

HIR

E

CO

MP

AN

CO

MP

AN

YR

Quick View Setup Figure 11.0: Quick View Setup Diagram


12

Cables Available from Hampshire Table 12.0: Available Communication Cables

Part Number: Description: C72-100S2F-09XDXF 6’ RS-232 cable. Direct connect H1 header to female DB-9

C72-040S1F-04XAXM 6’ USB cable. Direct connect H3 header to male type-A plug connector

Table 12.1: Available Power Cables C20-020S1F-XXXXX 20” power cable, Direct connect to H2. 2 position, .100” socket to wire lead.

C20-020S1F-020S1F 20” power cable, Direct connect to H2. 2 position, .100” socket to 2 position .100” socket


Setup and User’s Manual TSHARC “C-Ray” Capacitive Touch Screen … · 2017. 9. 12. · touch...

Documents

Transcript of Setup and User’s Manual TSHARC “C-Ray” Capacitive Touch Screen … · 2017. 9. 12. · touch...