SERVICE MANUAL AEP Model UK Model Ver 1.0 2001diagramas.diagramasde.com/otros/SA-WMS - SS-V -...
12
SERVICE MANUAL SS-V225 (Front and rear speakers) Speaker system Full range, magnetically shielded Speaker units 5 × 9 cm, cone type Enclosure type Bass reflex Rated impedance 8 ohms Power handling capacity Maximum input power: 100 watts Sensitivity level 86 dB (1 W, 1 m) Frequency range 90 Hz - 20,000 Hz Dimensions (w/h/d) Approx. 70 × 151 × 126 mm, including front grille Mass Approx. 550 g each SS-CN225 (Center speaker) Speaker system Full range × 2, magnetically shielded Speaker units 5 × 9 cm, cone type Enclosure type Bass reflex Rated impedance 8 ohms Power handling capacity Maximum input power: 120 watts Sensitivity level 88 dB (1 W, 1 m) Frequency range 90 Hz - 20,000 Hz Dimensions (w/h/d) Approx. 301 × 70 × 126 mm, including front grille Mass Approx. 1.1 kg SA-WMS225 (subwoofer) Speaker system Active subwoofer, magnetically shielded Speaker unit Woofer: 16 cm, cone type Enclosure type Advanced SAW type Amplifire section Continuous RMS power output 50 W(8 ohms, 20 - 150 Hz, 0.8% THD) Reproduction frequency range 28 Hz - 200 Hz High frequency cut-off frequency 200 Hz Inputs LINE IN (input pin jack) SPEAKER IN (input terminals) Outputs LINE OUT (output pin jack) SPEAKER OUT (output terminals) General Power requirements 220 - 230 V AC, 50/60 Hz Power consumptions 50 W Dimensions (w/h/d) Approx. 205 × 385 × 385 mm, including front grille Mass Approx. 10.5 kg Supplied accessories Foot pads (20) Monaural connecting cord (1 phono to 1 phono) (1) Speaker connecting cords, 10 m (2) Speaker connecting cords, 3.5 m (3) Speaker connecting cords, 2.5 m (2) Design and specifications are subject to change without notice. MICRO SATELLITE SYSTEM AEP Model UK Model Ver 1.0 2001.02 9-929-575-11 Sony Corporation 2001B0500-1 Audio Entertainment Group C 2001.2 General Engineering Dept. SPECIFICATIONS SA-VE225/WMS225/ SS-CN225/V225 • SA-VE225 consists of the following models respectively. SA-VE225 Active Subwoofer SA-WMS225 Center Speaker SS-CN225 Front and Rear Speakers SS-V225 SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. SA-WMS225 SS-V225 SS-CN225
-
Upload
duongkhanh -
Category
Documents
-
view
228 -
download
1
Transcript of SERVICE MANUAL AEP Model UK Model Ver 1.0 2001diagramas.diagramasde.com/otros/SA-WMS - SS-V -...
SERVICE MANUAL
SS-V225 (Front and rear speakers)Speaker system Full range, magnetically
shieldedSpeaker units 5 × 9 cm, cone typeEnclosure type Bass reflexRated impedance 8 ohmsPower handling capacityMaximum input power: 100 wattsSensitivity level 86 dB (1 W, 1 m)Frequency range 90 Hz - 20,000 HzDimensions (w/h/d) Approx. 70 × 151 ×
126 mm, including frontgrille
Mass Approx. 550 g each
SS-CN225 (Center speaker)Speaker system Full range × 2,
magnetically shieldedSpeaker units 5 × 9 cm, cone typeEnclosure type Bass reflexRated impedance 8 ohmsPower handling capacityMaximum input power: 120 wattsSensitivity level 88 dB (1 W, 1 m)Frequency range 90 Hz - 20,000 HzDimensions (w/h/d) Approx. 301 × 70 ×
126 mm, including frontgrille
Mass Approx. 1.1 kg
SA-WMS225 (subwoofer)Speaker system Active subwoofer,
magnetically shieldedSpeaker unit Woofer: 16 cm, cone typeEnclosure type Advanced SAW typeAmplifire section Continuous RMS power output
50 W(8 ohms, 20 - 150 Hz,0.8% THD)
Reproduction frequency range28 Hz - 200 Hz
High frequency cut-off frequency200 Hz
Inputs
LINE IN (input pin jack)SPEAKER IN (input terminals)
Outputs
LINE OUT (output pin jack)SPEAKER OUT (output terminals)
General
Power requirements 220 - 230 V AC, 50/60 HzPower consumptions 50 WDimensions (w/h/d) Approx. 205 × 385 × 385
mm, including front grilleMass Approx. 10.5 kg
Supplied accessoriesFoot pads (20)Monaural connecting cord (1 phono to 1 phono) (1)Speaker connecting cords, 10 m (2)Speaker connecting cords, 3.5 m (3)Speaker connecting cords, 2.5 m (2)
Design and specifications are subject to change withoutnotice.
MICRO SATELLITE SYSTEM
AEP ModelUK Model
Ver 1.0 2001.02
9-929-575-11 Sony Corporation2001B0500-1 Audio Entertainment Group
C 2001.2 General Engineering Dept.
SPECIFICATIONS
SA-VE225/WMS225/SS-CN225/V225
• SA-VE225 consists of the following models respectively.
SA-VE225
Active Subwoofer SA-WMS225
Center Speaker SS-CN225
Front and Rear Speakers SS-V225
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTEDLINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMSAND IN THE PARTS LIST ARE CRITICAL TO SAFEOPERATION. REPLACE THESE COMPONENTS WITHSONY PARTS WHOSE PART NUMBERS APPEAR ASSHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-LISHED BY SONY.
SA-WMS225 SS-V225SS-CN225
2
SA-VE225/WMS225/SS-CN225/V225SECTION 1DIAGRAMS
1-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Boards:• X : parts extracted from the component side.• : Pattern from the side which enables seeing.
Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolyticsand tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.• 2 : nonflammable resistor.• 5 : fusible resistor.• C : panel designation.
• A : B+ Line.• B : B– Line.• Voltages are dc with respect to ground under no-signal
conditions.• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-tion tolerances.
• Signal path.F : AUDIO
Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.
SA-VE225/WMS225/SS-CN225/V225
33
THERMALSHUTDOWNBIPOLAR
TRANSCONDACTANCEINPUT STAGE
STANDBY/MUTE
BOOST-STRAP
MOS GAIN &LEVEL SHIFTING
STAGE
STBY
-GND IN
–
IN+
IN+
MUT
E
NC
BOOS
TSTR
AP +VS
–VS
STBY
MUT
E
NC NC
+PW
VS OUT
–PW
VS
14 1512 1310 118 96 753 41 2
+– MOS
OUTPUTSTAGE
SHORTCIRCUIT
PROTECTION
1 2 3 4 5 6 7 8
OVER LOAD DET
F/FOFFSET DET
LATCH/AUTORESET
VCC ONMUTE
AC OFFDET
OVER
LOA
D DE
T
OFFS
ET D
ET
AUTO
RES
ET
AC O
FF D
ET
GND
RELA
Y D
RIVE
VCC
ON M
UTE
VCC
• IC Block Diagrams
– MAIN Board –IC302 µPC1237HA
• Circuit Boards Location SA-WMS225
POWER IC board
POWER SW board
LED board
CONTROL board
MAIN board
– POWER IC Board –IC401 TDA7294
SA-VE225/WMS225/SS-CN225/V225
44
LED BOARD
LEVEL
MODE
MUSIC
MOVIE
(POWER)
SP1(SPEAKER)
11
1-676-716- (13)
11
(13)
11
(13)
11
(11)
MAIN BOARD
POWER
T501POWER
TRANSFORMER
ACIN
11
(13)
CONTROL BOARD
POWER SWBOARD
POWER IC BOARD
SPEAKERR L
OUT IN
r
1-67
6-71
3
LINE
1-67
7-99
3-
1-67
6-71
4-
1-676-565-
R102 R101
R103 R104
1 2
A
B
C
D
E
F
G
H
3 4 5 6 7 8 9 10 11
1-2. PRINTED WIRING BOARDS (SA-WMS225) • See page 3 for Circuit Boards Location.
• SemiconductorLocation
Ref. No. Location
D101 G-11D102 F-11D103 G-10D104 G-10D301 F-8D302 F-8D303 F-5D304 D-8D501 G-5D502 G-7D503 H-7D801 B-7
IC101 G-11IC102 G-9IC103 E-11IC201 B-3IC302 E-10IC401 B-10
Q101 G-9Q102 G-8Q103 E-10Q303 D-9
SA-VE225/WMS225/SS-CN225/V225
55
OVER
LOAD
DET
OFFS
ET D
ET
AUTO
RES
ET
AC O
FF D
ET
GND
VCC
ON M
UTE
VCC
RELA
YDR
IVE
(1/2)
(1/2)
(2/2)
(2/2)
(2/2)(1/2)
MIX AMP
(1/2)
(1/2)HIGH-PASS FILTER
(2/2)LOW-PASS FILTER
(2/2)
1A 250V
BUFFER
(1/2)
3
21
(2/2)
(CHASSIS)
D3041SS133
7P
7P
RBA-402-SL
RBA-402-SL
RBA-406B
1-3. SCHEMATIC DIAGRAM (SA-WMS225) • See page 3 for IC Block Diagrams.
The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
SA-VE225/WMS225/SS-CN225/V225
66
2-1. FRONT PANEL SECTION (SA-WMS225)
SECTION 2EXPLODED VIEWS
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
• Items marked “*” are not stocked since theyare seldom required for routine service. Somedelay should be anticipated when orderingthese items.
• The mechanical parts with no reference num-ber in the exploded views are not supplied.
• Accessories and packing materials are givenin the last of the electrical parts list.
• Hardware (# mark) list and accessories andpacking materials are given in the last of theelectrical parts list.
NOTE:• -XX and -X mean standardized parts, so they
may have some difference from the originalone.
• Color Indication of Appearance PartsExample:KNOB, BALANCE (WHITE) . . . (RED)
↑ ↑Parts Color Cabinet's Color
2-2. REAR PANEL SECTION (SA-WMS225)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-4952-542-1 FRAME ASSY, GRILLE (BLACK)1 X-4953-558-1 FRAME ASSY, GRILLE (SILVER)2 X-4952-603-1 PANEL ASSY, FRONT (BLACK)2 X-4953-559-1 PANEL ASSY, FRONT (SILVER)3 4-973-938-41 KNOB (A), PUSH (BLACK)
3 4-973-938-71 KNOB (A), PUSH (SILVER)4 4-227-298-01 SHEET5 4-226-228-01 KNOB (VOL) (BLACK)5 4-226-228-11 KNOB (VOL) (SILVER)
7 1-676-565-11 LED BOARD8 1-676-716-11 POWER SW BOARD9 A-4428-444-A CONTROL BOARD, COMPLETE10 A-4411-960-A CABINET ASSY, SPEAKER (BLACK)10 A-4412-745-A CABINET ASSY, SPEAKER (SILVER)
11 4-981-864-01 FOOT12 4-226-227-01 PACKING (D)SP1 1-529-589-11 SPEAKER (16cm)
51 1-676-714-11 POWER IC BOARD052 1-777-071-21 CORD, POWER* 53 3-703-244-00 BUSHING (2104), CORD
54 4-227-118-61 PANEL, REAR55 A-4720-478-A MAIN BOARD, COMPLETE
0T501 1-435-895-11 TRANSFORMER, POWER
The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
1
10
3 5
7
911
4
8
not supplied
12
2
supplied withRV201, S201
rear panel section
#3
#3
#8
#8SP1
#2
#2
#9
#7
#7
#3
#3
#3
#3
#4#4
#4
#6
not supplied
not supplied
not supplied
T501
53
54
51
55
52
7
SA-VE225/WMS225/SS-CN225/V225
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
2-3. SS-CN225
101 X-4952-574-1 PANEL ASSY, FRONT (BLACK)101 X-4953-560-1 PANEL ASSY, FRONT (SILVER)102 3-703-564-31 SCREW (DIA. 3.5)103 X-4952-575-1 CABINET ASSY, SPEAKER (BLACK)103 X-4953-561-1 CABINET ASSY, SPEAKER (SILVER)
104 1-694-516-11 TERMINAL, SPEAKER (BLACK)104 1-694-516-21 TERMINAL, SPEAKER (SILVER)SP2 1-529-578-11 SPEAKER (5X9cm)SP3 1-529-578-11 SPEAKER (5X9cm)
101
not supplied
103
102
104
#1
SP2
SP3
#5
#5
8
SA-VE225/WMS225/SS-CN225/V225
2-4. SS-V225
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 X-4952-572-1 PANEL ASSY, FRONT (BLACK)151 X-4953-562-1 PANEL ASSY, FRONT (SILVER)152 3-703-564-31 SCREW (DIA. 3.5)153 X-4952-573-1 CABINET ASSY, SPEAKER (BLACK)
153 X-4953-563-1 CABINET ASSY, SPEAKER (SILVER)154 1-164-516-11 TERMINAL, SPEAKER (BLACK)154 1-164-516-21 TERMINAL, SPEAKER (SILVER)SP4 1-529-577-11 SPEAKER (5X9cm)
151SP4
153 #1
#5
154
152
not supplied
9
SA-VE225/WMS225/SS-CN225/V225
CONTROL
LED MAIN
SECTION 3ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-4428-444-A CONTROL BOARD, COMPLETE*************************
< CAPACITOR >
C201 1-162-215-31 CERAMIC 47PF 5% 50VC203 1-126-964-11 ELECT 10uF 20% 50VC204 1-126-964-11 ELECT 10uF 20% 50VC205 1-126-964-11 ELECT 10uF 20% 50VC206 1-126-964-11 ELECT 10uF 20% 50V
C207 1-130-495-00 MYLAR 0.1uF 5% 50VC208 1-130-495-00 MYLAR 0.1uF 5% 50V
< CONNECTOR >
* CN201 1-564-511-11 PLUG, CONNECTOR 8P
< IC >
IC201 8-759-634-50 IC M5218AL
< RESISTOR >
R201 1-249-429-11 CARBON 10K 5% 1/4WR203 1-249-429-11 CARBON 10K 5% 1/4WR204 1-249-429-11 CARBON 10K 5% 1/4WR205 1-249-429-11 CARBON 10K 5% 1/4WR206 1-249-433-11 CARBON 22K 5% 1/4W
< VARIABLE RESISTOR >
RV201 1-225-826-11 RES, VAR, CARBON 20K (LEVEL)
< SWITCH >
S201 1-771-632-11 SWITCH, ROTARY (MODE)**************************************************************
1-676-565-11 LED BOARD**********
< CONNECTOR >
CN801 1-564-505-11 PLUG, CONNECTOR 2P
< LED >
D801 8-719-038-54 LED SEL6414E-LC05 (POWER)**************************************************************
NOTE:• Due to standardization, replacements in the
parts list may be different from the parts speci-fied in the diagrams or the components usedon the set.
• -XX and -X mean standardized parts, so theymay have some difference from the originalone.
• RESISTORSAll resistors are in ohms.METAL: Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F: nonflammable
• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated when order-ing these items.
• SEMICONDUCTORSIn each case, u: µ, for example:uA. . : µA. . uPA. . : µPA. .uPB. . : µPB. . uPC. . : µPC. .uPD. . : µPD. .
• CAPACITORSuF: µF
• COILSuH: µH
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
When indicating parts by referencenumber, please include the board.
A-4720-478-A MAIN BOARD, COMPLETE*********************
< CAPACITOR >
0C1 1-113-924-11 CERAMIC 0.0047uF 20% 250V0C2 1-113-924-11 CERAMIC 0.0047uF 20% 250V
C101 1-162-286-31 CERAMIC 220PF 10% 50VC102 1-162-286-31 CERAMIC 220PF 10% 50VC103 1-162-286-31 CERAMIC 220PF 10% 50V
C104 1-126-964-11 ELECT 10uF 20% 50VC105 1-162-215-31 CERAMIC 47PF 5% 50VC106 1-162-286-31 CERAMIC 220PF 10% 50VC107 1-136-167-00 MYLAR 0.15uF 5% 50VC108 1-136-159-00 MYLAR 0.033uF 5% 50V
C109 1-136-169-00 MYLAR 0.22uF 5% 50VC110 1-136-169-00 MYLAR 0.22uF 5% 50VC111 1-136-169-00 MYLAR 0.22uF 5% 50VC112 1-136-169-00 MYLAR 0.22uF 5% 50VC113 1-136-165-00 MYLAR 0.1uF 5% 50V
C114 1-136-165-00 MYLAR 0.1uF 5% 50VC115 1-136-169-00 MYLAR 0.22uF 5% 50VC301 1-126-964-11 ELECT 10uF 20% 50VC302 1-136-165-00 MYLAR 0.1uF 5% 50VC303 1-126-933-11 ELECT 100uF 20% 16V
C304 1-136-165-00 MYLAR 0.1uF 5% 50VC305 1-126-964-11 ELECT 10uF 20% 50VC306 1-126-933-11 ELECT 100uF 20% 16VC307 1-126-963-11 ELECT 4.7uF 20% 50VC308 1-104-664-11 ELECT 47uF 20% 25V
C501 1-136-165-00 MYLAR 0.1uF 5% 50VC502 1-136-165-00 MYLAR 0.1uF 5% 50VC503 1-119-940-51 ELECT 4700uF 20% 50VC504 1-119-940-51 ELECT 4700uF 20% 50VC505 1-104-665-11 ELECT 100uF 20% 25V
C506 1-104-665-11 ELECT 100uF 20% 25VC507 1-126-964-11 ELECT 10uF 20% 50VC508 1-126-964-11 ELECT 10uF 20% 50VC509 1-136-165-00 MYLAR 0.1uF 5% 50VC510 1-136-165-00 MYLAR 0.1uF 5% 50V
C511 1-136-165-00 MYLAR 0.1uF 5% 50VC512 1-136-165-00 MYLAR 0.1uF 5% 50V
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
10
SA-VE225/WMS225/SS-CN225/V225
MAIN POWER IC
< CONNECTOR >
* CN101 1-564-511-11 PLUG, CONNECTOR 8P* CN301 1-564-510-11 PLUG, CONNECTOR 7P* CN302 1-565-792-11 PIN, CONNECTOR 2P* CN501 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P* CN502 1-564-687-11 PIN, CONNECTOR 3P
< DIODE >
D101 8-719-991-33 DIODE 1SS133T-77D102 8-719-991-33 DIODE 1SS133T-77D103 8-719-991-33 DIODE 1SS133T-77D104 8-719-991-33 DIODE 1SS133T-77D301 8-719-991-33 DIODE 1SS133T-77
D302 8-719-991-33 DIODE 1SS133T-77D303 8-719-991-33 DIODE 1SS133T-77D304 8-719-991-33 DIODE 1SS133T-77D501 8-719-312-47 DIODE RBA-406BD502 8-719-025-03 DIODE RBA-402-SL
D503 8-719-025-03 DIODE RBA-402-SL
< FUSE >
0F501 1-532-463-31 FUSE (1A/250V)
< IC >
IC101 8-759-634-50 IC M5218ALIC102 8-759-634-50 IC M5218ALIC103 8-759-634-50 IC M5218ALIC302 8-759-111-68 IC uPC1237HA
< JACK >
J101 1-785-795-11 JACK, PIN 2P (LINE IN/OUT)
< TRANSISTOR >
Q101 8-729-178-55 TRANSISTOR 2SC2785-EQ102 8-729-178-55 TRANSISTOR 2SC2785-EQ103 8-729-178-55 TRANSISTOR 2SC2785-EQ303 8-729-029-66 TRANSISTOR DTC114ESA
< RESISTOR >
R101 1-249-425-11 CARBON 4.7K 5% 1/4WR102 1-249-425-11 CARBON 4.7K 5% 1/4WR103 1-249-437-11 CARBON 47K 5% 1/4WR104 1-249-437-11 CARBON 47K 5% 1/4WR105 1-249-429-11 CARBON 10K 5% 1/4W
R106 1-249-429-11 CARBON 10K 5% 1/4WR107 1-249-429-11 CARBON 10K 5% 1/4WR108 1-249-429-11 CARBON 10K 5% 1/4WR109 1-249-417-11 CARBON 1K 5% 1/4WR110 1-249-417-11 CARBON 1K 5% 1/4W
R111 1-249-429-11 CARBON 10K 5% 1/4WR112 1-249-417-11 CARBON 1K 5% 1/4WR113 1-249-417-11 CARBON 1K 5% 1/4WR114 1-249-441-11 CARBON 100K 5% 1/4WR115 1-249-429-11 CARBON 10K 5% 1/4W
R116 1-247-843-11 CARBON 3.3K 5% 1/4WR117 1-249-424-11 CARBON 3.9K 5% 1/4WR118 1-249-436-11 CARBON 39K 5% 1/4W
R119 1-249-417-11 CARBON 1K 5% 1/4WR120 1-249-435-11 CARBON 33K 5% 1/4W
R121 1-249-425-11 CARBON 4.7K 5% 1/4WR122 1-249-439-11 CARBON 68K 5% 1/4WR123 1-249-417-11 CARBON 1K 5% 1/4WR124 1-249-435-11 CARBON 33K 5% 1/4WR125 1-249-425-11 CARBON 4.7K 5% 1/4W
R126 1-249-435-11 CARBON 33K 5% 1/4WR127 1-249-440-11 CARBON 82K 5% 1/4WR128 1-249-424-11 CARBON 3.9K 5% 1/4WR129 1-249-427-11 CARBON 6.8K 5% 1/4WR130 1-249-427-11 CARBON 6.8K 5% 1/4W
R131 1-249-441-11 CARBON 100K 5% 1/4WR132 1-249-429-11 CARBON 10K 5% 1/4WR133 1-249-429-11 CARBON 10K 5% 1/4WR301 1-249-427-11 CARBON 6.8K 5% 1/4WR302 1-249-433-11 CARBON 22K 5% 1/4W
R303 1-249-433-11 CARBON 22K 5% 1/4WR304 1-249-412-11 CARBON 390 5% 1/4W
0R305 1-212-857-00 FUSIBLE 10 5% 1/4W FR306 1-249-429-11 CARBON 10K 5% 1/4WR307 1-249-429-11 CARBON 10K 5% 1/4W
R309 1-249-441-11 CARBON 100K 5% 1/4WR310 1-249-441-11 CARBON 100K 5% 1/4WR311 1-249-427-11 CARBON 6.8K 5% 1/4WR312 1-249-429-11 CARBON 10K 5% 1/4W
0R313 1-216-455-11 METAL OXIDE 560 5% 2W F
R314 1-249-439-11 CARBON 68K 5% 1/4WR315 1-249-430-11 CARBON 12K 5% 1/4W
0R316 1-215-868-00 METAL OXIDE 680 5% 1W F0R501 1-216-456-00 METAL OXIDE 820 5% 2W F0R502 1-216-456-00 METAL OXIDE 820 5% 2W F
< RELAY >
RY301 1-515-920-11 RELAY (24V)
< POWER TRANSFORMER >
0T501 1-435-895-11 TRANSFORMER, POWER
< TERMINAL >
TM101 1-537-922-11 TERMINAL BOARD (SP) (SPEAKER IN/OUT)**************************************************************
1-676-714-11 POWER IC BOARD***************
< CAPACITOR >
C401 1-126-965-11 ELECT 22uF 20% 50V
< CONNECTOR >
* CN401 1-564-510-11 PLUG, CONNECTOR 7P
< IC >
IC401 8-759-660-72 IC TDA7294
The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
11
SA-VE225/WMS225/SS-CN225/V225
POWER IC POWER SW
< RESISTOR >
R401 1-249-429-11 CARBON 10K 5% 1/4WR402 1-249-429-11 CARBON 10K 5% 1/4W
**************************************************************
1-676-716-11 POWER SW BOARD****************
< CONNECTOR >
CN1 1-564-321-00 PIN, CONNECTOR 2P
< SWITCH >
0S1 1-554-920-11 SWITCH, PUSH (AC POWER) (1 KEY)(POWER)
**************************************************************
MISCELLANEOUS**************
052 1-777-071-21 CORD, POWER104 1-694-516-11 TERMINAL, SPEAKER (BLACK)104 1-694-516-21 TERMINAL, SPEAKER (SILVER)154 1-694-516-11 TERMINAL, SPEAKER (BLACK)154 1-694-516-21 TERMINAL, SPEAKER (SILVER)
SP1 1-529-589-11 SPEAKER (16cm)SP2 1-529-578-11 SPEAKER (5X9cm)SP3 1-529-578-11 SPEAKER (5X9cm)SP4 1-529-577-11 SPEAKER (5X9cm)
0T501 1-435-895-11 TRANSFORMER, POWER************************************************************
**************HARDWARE LIST**************
#1 7-621-846-40 SCREW (M4X16), TAPPING#2 7-685-165-01 SCREW +PTP 4X25 TYPE1#3 7-685-647-79 SCREW +P 3X10 TYPE2 NON-SLIT#4 7-685-648-79 SCREW +P 3X12 TYPE2 NON-SLIT#5 7-685-659-79 SCREW +BVTP 4X8 TYPE2 IT-3
#6 7-685-660-19 SCREW +BVTP 4X10 TYPE2 N-S#7 7-685-663-79 SCREW +BVTP 4X16 TYPE2 N-S#8 7-685-664-79 SCREW +PTP 4X20 TYPE1#9 7-685-665-79 SCREW +BVTP 4X25 TYPE2 N-S
************************************************************
ACCESSORIES & PACKING MATERIALS*******************************
0 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)1-769-329-21 CORD, CONNECTION (PIN-PIN)1-769-433-11 CORD, SPEAKER1-769-433-21 CORD, SPEAKER4-233-675-11 MANUAL, INSTRUCTION
(ENGLISH, FRENCH, GERMAN, ITALIAN)4-233-675-21 MANUAL, INSTRUCTION
(DUTCH, SPANISH, SWEDISH, POLISH) (AEP)4-972-322-01 FOOT (Y)
The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
SA-VE225/WMS225/SS-CN225/V225
REVISION HISTORY
Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.
Ver. Date Description of Revision
1.0 2001.02 New
