Self Closing Safety Gates & Spring Assemblies -...
Transcript of Self Closing Safety Gates & Spring Assemblies -...
Lockinex (UK) Ltd. Lockinex Works, Eastbourne, Hammonds Drive, East Sussex BN23 6PW Tel: 01323 737 626 Email: [email protected] Web: www.lockinex.com
Page ?
Lockinex
INTRODUCTIONLockinex safety gates are supplieddirect from stock, in standard formats.
Quick despatch and delivery ensuresseamless installation by the engineer or end user.Simple to operate and with speciallydesigned torsion springs on the hinges,they are “self closing”.
Ensuring a safe working environmentfor personnel. these heavy duty robustgates are a reliable resilient product.
APPLICATIONSelf closing Safety Gates are commonly in industry such as, processing plants, factories, wastemanagement. Installation in Walkways,access points, staircases, access ladders,ramps and high level walking areas.
COMPOSITION, MANUFACTUREManufactured form mild steel, with agalvanised finish.
Springs are stainless steel.
Powder coating can be applied to gatesif required.
Galvanised & Yellow coated gates are stock items.
DESIGN
Lockinex gates are manufactured frommanipulated tubing sections & plate steel.
Fully welded, they are of a one piece construction.
This provides the most robust applicationfor purpose and is proven to be the most successfuldesign for long term durability
Lockinex DO NOT employ any clamps or brackets inthe gate chassis/construction.
Page 2
of 8
1.0mtr wide Self Closing Safety gatewith optional mesh kit in�ll.
Lockinex (UK) Ltd. Lockinex Works, Eastbourne, Hammonds Drive, East Sussex BN23 6PW Tel: 01323 737 626 Email: [email protected] Web: www.lockinex.com Pag
e 3 of
8
Page ?
Padlock-able slam plate
Nominal 1000mm clear opening
1500mm(Cut to suit
on site)Gate manufacturedin 42.4mm dia tube.
Safely enclosedspring housing
Incorporating the Lockinex Safety enclosed spring hinge.This Self closing gate comes with a hot dipped galvanised �nish as standard. The gate is of a superior, welded construction. Posts are available in 42.4mm dia or 48.3mm dia (Please specify when ordering). Gate functions through a 180 degree arc- maximum. Gate may be cut down to suit required opening and re-joined using the Lockinex gate adjustment kit.
Gate-117-42.4mm posts
Gate-1348.3mm posts
Optional Mesh panel & Clips.Order Code“Mesh KIt-5”
The A02 and the A06 can be used to create a run of hand-railing from either gate post (as shown) if required. View the Lockinex Key Clamp brochure for our full clamp range.
Various base plates are available for the posts.Please refer to product
codes A12 to A17 inclusive in the Lockinex
Key Clamp brochure.
A06
A02
Galvanised to BS EN1461: 2009& Powder Coated RAL1023
Galvanised to BS EN1461: 2009
Lockinex (UK) Ltd. Lockinex Works, Eastbourne, Hammonds Drive, East Sussex BN23 6PW Tel: 01323 737 626 Email: [email protected] Web: www.lockinex.com
Gate-01Full Height Gate with-42.4mm dia posts & Integral Toe Board.
Gate-03Full Height Gate with-48.3mm dia posts & Integral Toe Board.
Mesh Panels optional forupper & lower openings.(Order “Mesh-Kit-6”)
Mesh Panels optional forupper & lower openings.(Order “Mesh-Kit-6”)
1.0mtr wide nominal
The A02 and the A06 can be used to create a run of hand-railing from the padlock eye gate post (as shown).View the Lockinex Key Clamp brochure for our full clamp range.
Various base plates are available for the posts.Please refer to product
codes A12 to A17 inclusive in the Lockinex
Key Clamp brochure.
Note!The A32Retro Fit Tis requiredon the hingedpost whenconnectinga horizontal rail
A06
A06
A02
A32
Page 4
of 8
Lockinex (UK) Ltd. Lockinex Works, Eastbourne, Hammonds Drive, East Sussex BN23 6PW Tel: 01323 737 626 Email: [email protected] Web: www.lockinex.com
Page ?
Page 5
of 8
Slam plate
715mm Nominal
578
56
49
437 Nominal
584Nominal
Stainless steel spring & bolts
Incorporating the Lockinex enclosed safety spring.This gate is primarily used with our access ladder system. It is a�xed at the top of the ladder at the exit point. It can be purchased separately and utilised as a safety gate for other purposes. This gate isself-closing. Perfectly Designed -The gate is of a superior, fully welded construction. Gate functions through 180 degree. Tensioning spring in either a clockwise or anti-clockwise direction to swing gate either way, it can be hung left or right handed. Gate may be cut down to suit required opening and re-joined using the Lockinex gate adjustment kit.
Galvanised to BS EN1461: 2009
If connecting to tube,use 2 x A36 clamps.(Specify tube sizewhen ordering) &2 x M10 x 40 Bolts & Nuts
A36
Optional Mesh panel & Clips.Order Code“Mesh KIt-1”
715mm Nominal
578
Steel toe board/kick plate.
1175Nominal
100
56
75
Slam plate
80
1079 Nominal
GLS-Full height gategalvanised
This gate is primarily used with our access ladder system. It is a�xed at the top of the ladder at the exit point. It can be purchased separately and utilised as a safety gate for other purposes. This gate is self-closing. Perfectly Designed -The gate is of a superior welded construction. When using this gate you satisfy BS 4592-0:2006+A1:2012. Gate functions through 90 degree.
* Springs may vary in design to illustrations shown.
Galvanised to BS EN1461: 2009
If connecting to tube,use 2 x A36 clamps.(Specify tube sizewhen ordering) &2 x M10 Bolts & Nuts
A36
Optional Mesh panels & Clips.Order Code“Mesh KIt-3”
GLS-Half height gate-galvanised.With enclosed safety spring design.
Page 6
of 8
The Lockinex gate adjustment kit consists of 2 x A08-7 Lockinex key clamps which provide astrong joint between the 2 halves of the cut gate. Simply cut the gate vertically to suit the opening dimension required and rejoin using the gate adjustment kit.
Gate adjustment kit
Lockinex (UK) Ltd. Lockinex Works, Eastbourne, Hammonds Drive, East Sussex BN23 6PW Tel: 01323 737 626 Email: [email protected] Web: www.lockinex.com
GS-02 Gate spring set
Self colour lugs for welding.
Enclosed stainless steel spring set. The main body/housing is galvanised to BS EN1461: 2009. The hinges are self colour readyfor welding. The maximum load the spring can hold and still function properly is 10kg. If the load is greater than 10kg, considerusing more than 1 spring. Spring functions through 180 degree maximum.
Spring is inserted into housing
Galvanisedspring housing
Countersunk hole for M8 X 20 countersunk screw (included)
Countersunk hole for M8 X 20 countersunk screw (included)
14mm hole for slotted pin
Slotted pin locatesonto leg of spring
Self colour for welding to gate
Self colour for welding to post
Take the gate and align the top hinge with the upper tang of the spring, (Viewable from the top of the spring housing). Lower the gate into the respective hinge bodies.Set the gate in its CLOSED position between the posts.Turn bolt half turn , to increase spring torsion, in either a clockwise or anti-clockwise direction. This will swing the gate in the direction of choice. The gate can be hung left handed or right handed.Over torsion will damage the internal spring.
Stainless steelspring
Slotted bolt locatesonto leg of spring
Bearing Washer (Included)Apply Grease on both sides
Prior to attachment of the gate,set this locking nut approximatelyhalfway down the length of the bolt.Turn bolt clockwise into the spring housing(aligning the lower spring tang in its slot)until locking nut reaches the spring housing. (This action compresses the spring within the housing.)
Hole for cotter pin (included)
Self colour for welding to gate
Self colour for welding to post
Bearing Washer (Included)Apply Grease on both sides
Retaining Washer (Included)
80
Page 7
of 8
Galvanised spring housing.
Lower Hinge assembly
Upper Hinge assembly
Self colour lugs for welding.
Lockinex (UK) Ltd. Lockinex Works, Eastbourne, Hammonds Drive, East Sussex BN23 6PW Tel: 01323 737 626 Email: [email protected] Web: www.lockinex.com
Page ?
Page 7
of 7
Page ?
of ?
GL01Galvanised
122 Nominal
176 Nominal(May vary)
200 Nominal
30
145 Nominal(May vary)
Gate latch and striking pin (Note, please state diameter of tube it is being �xed to). 3 x Lockinex A36 clamps are required to �x to the supporting tube. Relevant �xings/screws are also required seperatelyto connect latch to A36’s.
GLS-Gatespring setgalvanisedor self colour
56 Nominal
61 Nominal
12 Dia
25
Stainless steel
155 Nominal 170 Nominal
56 Nominal
Thickness of 8mm
Stainless steel spring & bolt
25
12 Dia
70
38
Gate spring set. Available with all mild steel components in galvanised or self colour (For welding). The suggested maximum weight of the gate 10kg. Use multiple springs if gate is heavier. Spring functions through 90 degrees max.
Page 8
of 8