SEFOS CLI Reference Manual, Volume 7 · 2015. 8. 14. · 8 Sun Ethernet Fabric Operating System CLI...

Sun Ethernet Fabric Operating System CLI Reference Manual, Vol. 7

Part No: E60931-02

August 2015

Copyright © 2015, Oracle and/or its affiliates. All rights reserved.

This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws. Except as expressly permitted in your license agreement or allowed by law, you may not use, copy, reproduce, translate, broadcast, modify, license, transmit, distribute, exhibit, perform, publish, or display any part, in any form, or by any means. Reverse engineering, disassembly, or decompilation of this software, unless required by law for interoperability, is prohibited.

The information contained herein is subject to change without notice and is not warranted to be error-free. If you find any errors, please report them to us in writing.

If this is software or related documentation that is delivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, then the following notice is applicable:

U.S. GOVERNMENT END USERS. Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.

This software or hardware is developed for general use in a variety of information management applications. It is not developed or intended for use in any inherently dangerous applications, including applications that may create a risk of personal injury. If you use this software or hardware in dangerous applications, then you shall be responsible to take all appropriate fail-safe, backup, redundancy, and other measures to ensure its safe use. Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this software or hardware in dangerous applications.

Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners.

Intel and Intel Xeon are trademarks or registered trademarks of Intel Corporation. All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. AMD, Opteron, the AMD logo, and the AMD Opteron logo are trademarks or registered trademarks of Advanced Micro Devices. UNIX is a registered trademark of The Open Group.

This software or hardware and documentation may provide access to or information about content, products, and services from third parties. Oracle Corporation and its affiliates are not responsible for and expressly disclaim all warranties of any kind with respect to third-party content, products, and services unless otherwise set forth in an applicable agreement between you and Oracle. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third-party content, products, or services, except as set forth in an applicable agreement between you and Oracle.

Documentation Accessibility

For information about Oracle's commitment to accessibility, visit the Oracle Accessibility Program website at http://www.oracle.com/pls/topic/lookup?ctx=acc&id=docacc.

Access to Oracle Support

Oracle customers that have purchased support have access to electronic support through My Oracle Support. For information, visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=info or visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs if you are hearing impaired.

Copyright © 2015, Oracle et/ou ses affiliés. Tous droits réservés.

Ce logiciel et la documentation qui l'accompagne sont protégés par les lois sur la propriété intellectuelle. Ils sont concédés sous licence et soumis à des restrictions d'utilisation et de divulgation. Sauf stipulation expresse de votre contrat de licence ou de la loi, vous ne pouvez pas copier, reproduire, traduire, diffuser, modifier, breveter, transmettre, distribuer, exposer, exécuter, publier ou afficher le logiciel, même partiellement, sous quelque forme et par quelque procédé que ce soit. Par ailleurs, il est interdit de procéder à toute ingénierie inverse du logiciel, de le désassembler ou de le décompiler, excepté à des fins d'interopérabilité avec des logiciels tiers ou tel que prescrit par la loi.

Les informations fournies dans ce document sont susceptibles de modification sans préavis. Par ailleurs, Oracle Corporation ne garantit pas qu'elles soient exemptes d'erreurs et vous invite, le cas échéant, à lui en faire part par écrit.

Si ce logiciel, ou la documentation qui l'accompagne, est concédé sous licence au Gouvernement des Etats-Unis, ou à toute entité qui délivre la licence de ce logiciel ou l'utilise pour le compte du Gouvernement des Etats-Unis, la notice suivante s'applique:

U.S. GOVERNMENT END USERS. Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.

Ce logiciel ou matériel a été développé pour un usage général dans le cadre d'applications de gestion des informations. Ce logiciel ou matériel n'est pas conçu ni n'est destiné à être utilisé dans des applications à risque, notamment dans des applications pouvant causer des dommages corporels. Si vous utilisez ce logiciel ou matériel dans le cadre d'applications dangereuses, il est de votre responsabilité de prendre toutes les mesures de secours, de sauvegarde, de redondance et autres mesures nécessaires à son utilisation dans des conditions optimales de sécurité. Oracle Corporation et ses affiliés déclinent toute responsabilité quant aux dommages causés par l'utilisation de ce logiciel ou matériel pour ce type d'applications.

Oracle et Java sont des marques déposées d'Oracle Corporation et/ou de ses affiliés. Tout autre nom mentionné peut correspondre à des marques appartenant à d'autres propriétaires qu'Oracle.

Intel et Intel Xeon sont des marques ou des marques déposées d'Intel Corporation. Toutes les marques SPARC sont utilisées sous licence et sont des marques ou des marques déposées de SPARC International, Inc. AMD, Opteron, le logo AMD et le logo AMD Opteron sont des marques ou des marques déposées d'Advanced Micro Devices. UNIX est une marque déposée d'The Open Group.

Ce logiciel ou matériel et la documentation qui l'accompagne peuvent fournir des informations ou des liens donnant accès à des contenus, des produits et des services émanant de tiers. Oracle Corporation et ses affiliés déclinent toute responsabilité ou garantie expresse quant aux contenus, produits ou services émanant de tiers, sauf mention contraire stipulée dans un contrat entre vous et Oracle. En aucun cas, Oracle Corporation et ses affiliés ne sauraient être tenus pour responsables des pertes subies, des coûts occasionnés ou des dommages causés par l'accès à des contenus, produits ou services tiers, ou à leur utilisation, sauf mention contraire stipulée dans un contrat entre vous et Oracle.

Accessibilité de la documentation

Pour plus d'informations sur l'engagement d'Oracle pour l'accessibilité à la documentation, visitez le site Web Oracle Accessibility Program, à l'adresse http://www.oracle.com/pls/topic/lookup?ctx=acc&id=docacc.

Accès au support électronique

Les clients Oracle qui ont souscrit un contrat de support ont accès au support électronique via My Oracle Support. Pour plus d'informations, visitez le site http://www.oracle.com/pls/topic/lookup?ctx=acc&id=info ou le site http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs si vous êtes malentendant.

http://www.oracle.com/pls/topic/lookup?ctx=acc&id=docacchttp://www.oracle.com/pls/topic/lookup?ctx=acc&id=infohttp://www.oracle.com/pls/topic/lookup?ctx=acc&id=trshttp://www.oracle.com/pls/topic/lookup?ctx=acc&id=docacc../../../OpusWS/RefMan7/site%20http:/www.oracle.com/pls/topic/lookup?ctx=acc&id=info%20../../../OpusWS/RefMan7/site%20http:/www.oracle.com/pls/topic/lookup?ctx=acc&id=info%20http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs

3

Contents

Using This Documentation .............................................................................................................. 5

45. MLDv2 ................................................................................................................................................. 7

45.1 ipv6 mld router .......................................................................................................................... 8

45.2 show ipv6 mld ........................................................................................................................... 9

45.3 set ipv6 mld .............................................................................................................................10

45.4 ipv6 mld immediate-leave .......................................................................................................11

45.5 ipv6 mld version ......................................................................................................................12

45.6 ipv6 mld query-interval ............................................................................................................13

45.7 ipv6 mld query-max-response-time ........................................................................................14

45.8 ipv6 mld robustness ................................................................................................................15

45.9 ipv6 mld last-member-query-interval ......................................................................................16

45.10 no ipv6 mld ..............................................................................................................................17

45.11 debug ipv6 mld........................................................................................................................18

45.12 show ipv6 mld global-config ....................................................................................................19

45.13 show ipv6 mld interface ..........................................................................................................20

45.14 show ipv6 mld groups .............................................................................................................24

45.15 show ipv6 mld sources ...........................................................................................................25

45.16 show ipv6 mld statistics ..........................................................................................................26

5

Using This Documentation

• Overview – Provides information on Oracle’s SEFOS CLI commands

• Audience – Users and system administrators who configure SEFOS through the CLI

• Required knowledge – Basic knowledge of UNIX CLI command syntax

Product Documentation Library

Documentation and resources for this product and related products are available at http://www.oracle.com/goto/es2-72_es2-64/docs.

Acronyms

Refer to the Sun Ethernet Fabric Operating System CLI Reference Manual, Vol. 1 for acronyms and abbreviations.

CLI Command Modes

Refer to the Sun Ethernet Fabric Operating System CLI Reference Manual, Vol. 1 for CLI command modes.

Feedback

Provide feedback about this documentation at http://www.oracle.com/goto/docfeedback.

http://www.oracle.com/goto/es2-72_es2-64/docshttp://www.oracle.com/goto/docfeedback

6 Sun Ethernet Fabric Operating System CLI Reference Manual, Vol. 7 August 2015

7

CHAPTER 45

MLDv2

Multicast Listener Discovery Version2 (MLDv2) is the protocol used by IPv6 systems to report their IP multicast group memberships to neighboring multicast routers. Version 2 of MLD adds support for source filtering, that is, the ability for a system to report interest in receiving packets only from specific source addresses, or from all but specific source addresses, sent to a particular multicast address. This information is used by multicast routing protocols to avoid delivering multicast packets from specific sources to networks where there are no interested receivers.


45.1 ipv6 mld router

Command Objective This command enables MLD message processing and egress routing of multicast packets on the interface.

The no form of the command disables MLD message processing and egress routing of multicast packets on the specified interface.

Syntax ipv6 mld router

no ipv6 mld router

Mode Interface configuration mode (VLAN)

Package Enterprise and Metro_E

Example SEFOS(config-if)# ipv6 mld router

Related Command(s) • show ipv6 mld - Displays the global configuration status of MLD protocol

in the router.

• show ipv6 mld interface - Displays the interface configuration of MLD.

Chapter 45 MLDv2 9

45.2 show ipv6 mld

Command Objective This command displays the global configuration status of MLD protocol in the router.

Syntax show ipv6 mld

Mode Privileged EXEC Mode


Example SEFOS# show ipv6 mld

MLD is globally disabled

Related Command(s) • set ipv6 mld - Enables or disables MLD.

• ipv6 mld router - Enables the MLD message processing and egress routing of multicast packets on the interface.


45.3 set ipv6 mld

Command Objective This command enables or disables MLD protocol in the router for protocol functioning, that is, the global status of MLD protocol in the router is set.

Syntax set ipv6 mld { enable | disable }

Syntax Description • enable - Enables MLD globally for protocol functioning.

• disable - Disables MLD globally. This removes all dynamic multicast entries, stops all the timers for route entries and disables MLD on all the MLD enabled interfaces.

Mode Global Configuration Mode


Defaults MLD is disabled on interface

Example SEFOS(config)# set ipv6 mld enable

Related Command • show ipv6 mld global-config - Displays the global configuration

status of MLD protocol in the router.

• show ipv6 mld groups - Displays information about the MLD groups.

Chapter 45 MLDv2 11

45.4 ipv6 mld immediate-leave

Command Objective This command enables fast leave processing on the interface. It provides the immediate intimation to the multicast routing protocol on the last member leaving the group.

This must be enabled only on those interfaces where there is single host. This can also be enabled on those interfaces having more than one host only if all are MLDv2 hosts in MLDv2 mode.

The no form of the command disables immediate-leave processing on the interface.

Syntax ipv6 mld immediate-leave

no ipv6 mld immediate-leave



Defaults Fast leave is disabled on interface.

Example SEFOS(config-if)# ipv6 mld immediate-leave

Related Command(s) show ipv6 mld interface - Displays the interface configuration of MLD.


45.5 ipv6 mld version

Command Objective This command configures the MLD version on the interface.

The no form of the command sets MLD version on the interface to its default value.

Syntax ipv6 mld version { 1 | 2 }

no ipv6 mld version

Parameter Description • version - Configures MLD version. The options are:

▪ 1 - Sets version 1 on the interface

▪ 2 - Sets version 2 on the interface



Defaults Version 1

Example SEFOS(config-if)# ipv6 mld version 1

Related Command • show ipv6 mld interface - Displays the interface configuration of

MLD.

Chapter 45 MLDv2 13

45.6 ipv6 mld query-interval

Command Objective This command configures MLD query interval for the interface. The query interval ranges between 1 and 31744.

The no form of the command sets MLD query-interval to its default value.

Note: The Query interval must be greater than 10 and the values from 1 to 10 are reserved for IGMP version 1.

Syntax ipv6 mld query-interval

no ipv6 mld query-interval



Defaults 125

Note: This command executes only if the query Interval is < (1/10) * Max Response Time.

Example SEFOS(config-if)# ipv6 mld query-interval 246

Related Command • ipv6 mld query-max-response-time - Configures MLD maximum

query response value for the interface.

• show ipv6 mld interface - Displays the interface configuration of MLD.


45.7 ipv6 mld query-max-response-time

Command Objective This command configures MLD maximum query response value for the interface. The query response value ranges between 1 and 31744 which is stored in one tenth of a second.

The no form of the command sets maximum query response to its default value.

Syntax ipv6 mld query-max-response-time

no ipv6 mld query-max-response-time



Defaults 100

Note: This command executes only if the maximum response time is less than (Query Interval * 11).

Example SEFOS(config-if)# ipv6 mld query-max-response-time 44


MLD.

Chapter 45 MLDv2 15

45.8 ipv6 mld robustness

Command Objective This command configures the MLD robustness value for the interface. MLD robustness value ranges between 2 and 255.

The no form of the command sets robustness value to its default value.

Syntax ipv6 mld robustness

no ipv6 mld robustness



Defaults 2

Example SEFOS(config-if)# ipv6 mld robustness 32


MLD.


45.9 ipv6 mld last-member-query-interval

Command Objective This command configures MLD last member query interval for the interface. The last member query interval is the maximum response delay inserted into group-specific queries sent in response to leave group messages, and is also the amount of time between group-specific query messages. This value is tuned to modify the leave latency of the network. A reduced value results in reduced time to detect the loss of the last member of a group.

The last member query interval value ranges between 1 and 31744 which is stored in one tenth of a second.

The no form of the command sets last member query interval to its default value.

Syntax ipv6 mld last-member-query-interval

no ipv6 mld last-member-query-interval



Defaults 10

Example SEFOS(config-if)#ipv6 mld last-member-query-interval 34

Related Command(s) • show ipv6 mld interface - Displays the interface configuration of

MLD.

Chapter 45 MLDv2 17

45.10 no ipv6 mld

Command Objective This command deletes the MLD capable interface, that is, disables MLD configuration on the interface.

Syntax no ipv6 mld



Example SEFOS(config-if)# no ipv6 mld


45.11 debug ipv6 mld

Command Objective This command enables the tracing of the MLDv2 module as per the configured debug levels. The trace statements are generated for the configured trace levels.

This command allows the combination of debug levels to be configured (that is, more than one level of trace can be enabled or disabled). The debug levels are configured one after the other and not in single execution of the command.

The no form of the command disables the tracing of the MLDv2 module as per the configured debug levels. The trace statements are not generated for the configured trace levels.

Syntax debug ipv6 mld ( [i/o][grp][qry][tmr][mgmt][all] )

no debug ipv6 mld ( [i/o][grp][qry][tmr][mgmt][all] )

Syntax Description • i/o - Generates debug statements for input/output traces.

• grp - Generates debug statements for group related traces.

• qry - Generates debug statements for Query related traces.

• tmr - Generates debug statements for timer module traces. This trace is generated on failed and successful start, stop, and restart of timers for route entries.

• mgmt - Generates debug statements for management traces.

• all - Generates debug statements for all kinds of traces.



Default all

Example SEFOS# debug ipv6 mld i/o

Chapter 45 MLDv2 19

45.12 show ipv6 mld global-config

Command Objective This command displays the global configuration status of MLD protocol in the router.

Syntax show ipv6 mld global-config



Example SEFOS# show ipv6 mld global-config

MLD is globally disabled



45.13 show ipv6 mld interface

Command Objective This command displays the interface configuration of MLD.

Syntax show ipv6 mld interface [{ Vlan | | }]

Syntax Description • vlan - Displays MLD configurations for the

specified VLAN / VFI ID. This value ranges from 1 to 65535.

▪ - VLAN ID is a unique value that represents the specific

VLAN. This value ranges from 1 to 4094.

▪ . - VFI ID is a VLAN created in the system which contains

pseudowires and attachment circuits as member ports. This creates a logical LAN for the virtual private LAN service (VPLS). This value ranges from 4096 to 65535.

Note: The VLAN ID 4095 is reserved and may be used to indicate a wildcard match for the VID in management operations or filtering database entries.

Note: VFI IDs 4096 and 4097 are reserved identifiers used in multiprotocol label switching (MPLS) pseudowire (PW).

Note: The theoretical maximum for the maximum number of VFI is 65535 but the actual number of VFI supported is a sizing constant. Based on this, the maximum number of VFI ID accepted in the management interface is restricted. For example, if 100 VFIs are supported, the maximum number of VFI supported is restricted to maximum number of VLANs + 100. An error message is displayed for any value beyond this range.

• - Displays the interface configuration of MLD for the specified type of interface. The interface can be:

▪ fastethernet – Officially referred to as 100BASE-T standard. This is

a version of LAN standard architecture that supports data transfer up to 100 Megabits per second.

▪ XL-ethernet – A version of LAN standard architecture that supports

data transfer up to 1 Gigabit per second.

Note: As of release 2.0.0.3, all interfaces are referred to as extreme-ethernet.

▪ extreme-ethernet – A version of Ethernet that supports data

transfer up to 10 Gigabits per second. This Ethernet supports only full duplex links.

▪ i-lan – Internal LAN created on a bridge per IEEE 802.1ap.

• - Displays the interface configuration of MLD for the specified ID of interface. This is a unique value that represents the specific interface. This value is a combination of slot number and port number separated by a slash, for interface type other than i-lan. For example, 0/1

Chapter 45 MLDv2 21

represents that the slot number is 0 and port number is 1. Only i-lan ID is provided, for interface type i-lan. For example, 1 represents i-lan ID.

• - Displays the interface configuration of MLD for the specified L3 pseudowire interface in the system.

• - Displays the interface configuration of MLD for the specified L3 pseudowire interface identifier. This is a unique value that represents the specific interface. This value ranges from 1 to 65535 for pseudowire interface.

Note: Maximum number of pseudowire interfaces supported in the system is 100.



Example SEFOS# show ipv6 mld interface

vlan1, line protocol is up

Internet Address is fe80::201:2ff:fe03:401

Prefix Length is 0

MLD is enabled on interface

Current MLD router version is 2

MLD query interval is 43 seconds

Last member query response interval is 10 seconds

MLD max query response time is 100 seconds

Robustness value is 33

MLD querying router is ::

Fast leave is enabled on this interface

No multicast groups joined

vlan2, line protocol is down

Internet Address is ::

Prefix Length is 0

MLD is disabled on interface







MLD querying router is :: (this system)

Fast leave is enabled on this interface


vlan3, line protocol is down

Internet Address is ::

Prefix Length is 0

MLD is disabled on interface






MLD querying router is :: (this system)

Fast leave is disabled on this interface


Related Command(s) • ipv6 mld router - Enables MLD message processing and egress

routing of multicast packets on the interface.

• set ipv6 mld - Enables or disables MLD protocol in the router for protocol functioning.

• ipv6 mld immediate-leave - Enables immediate leave processing on the interface.

• ipv6 mld version - Configures the MLD version on the interface.

• ipv6 mld query-interval - Configures MLD host query interval for the interface.

• ipv6 mld query-max-response-time - Configures MLD maximum query response value for the interface.

• ipv6 mld robustness - Configures MLD robustness value for the

Chapter 45 MLDv2 23

interface.

• ipv6 mld last-member-query-interval - Configures MLD last member query interval for the interface.


45.14 show ipv6 mld groups

Command Objective This command displays information for the MLD groups.

Syntax show ipv6 mld groups



Example SEFOS# show ipv6 mld groups

I - Include Mode, E - Exclude Mode

S - Static Mbr, D - Dynamic Mbr

GroupAddress Flg Iface UpTime ExpiryTime

LastReporter

--------------- --- ------- ---------------- --------------

-- ---------------

ff02::100 ID vlan1 [0d 00:00:04.85] [0d

00:00:00.00] fe80::202:2ff:fe03:111

Related Command(s) • set ipv6 mld - Enables or disables MLD protocol in the router for

protocol functioning.

• ipv6 mld router - Enables MLD message processing and egress routing of multicast packets on the interface.


Chapter 45 MLDv2 25

45.15 show ipv6 mld sources

Command Objective This command displays the MLD sources information.

Syntax show ipv6 mld sources



Example SEFOS# show ipv6 mld sources

I - Include Mode, E - Exclude Mode

S - Static Mbr, D - Dynamic Mbr

F - Forward List, N - Non-Forward List

GroupAddress Iface SrcAddress Flg ExpiryTime

LastReporter

--------------- ------- --------------- ---- --------------

-- ---------------

ff02::100 vlan1 8888::1111 IDF [0d

00:04:18.30] fe80::202:2ff:fe03:111


• ipv6 mld router - Enables MLD message processing and egress routing of multicast packets on the interface.



45.16 show ipv6 mld statistics

Command Objective This command displays the MLD statistics information.

Syntax show ipv6 mld statistics [{ Vlan | | }]

Syntax Description • vlan - Displays MLD statistics for the specified

VLAN or VFI ID. This value ranges from 1 to 65535.

▪ - VLAN ID is a unique value that represents the specific

VLAN. This value ranges from 1 to 4094.

▪ . - VFI ID is a VLAN created in the system which contains

pseudowires and attachment circuits as member ports. This creates a logical LAN for the VPLS service. This value ranges from 4096 to 65535.

Note: The VLAN ID 4095 is reserved and may be used to indicate a wildcard match for the VID in management operations or filtering database entries.

Note: VFI IDs 4096 and 4097 are reserved identifiers used in MPLS PW.

Note: The theoretical maximum for the maximum number of VFI is 65535 but the actual number of VFI supported is a sizing constant. Based on this, the maximum number of VFI ID accepted in the management interface is restricted. For example, if 100 VFIs are supported, the maximum number of VFI supported is restricted to maximum number of VLANs + 100. An error message is displayed for any value beyond this range.

• - Displays the MLD statistics information for the specified type of interface. The interface can be:

▪ fastethernet – Officially referred to as 100BASE-T standard. This is

a version of LAN standard architecture that supports data transfer up to 100 Megabits per second.

▪ XL-ethernet – A version of LAN standard architecture that supports

data transfer up to 1 Gigabit per second.

▪ extreme-ethernet – A version of Ethernet that supports data

transfer up to 10 Gigabits per second. This Ethernet supports only full duplex links.

▪ i-lan – Internal LAN created on a bridge per IEEE 802.1ap.

• - Displays the MLD statistics information for the specified ID of interface. This is a unique value that represents the specific interface. This value is a combination of slot number and port number separated by a slash, for interface type other than i-lan. For example, 0/1 represents that the slot number is 0 and port number is 1. Only i-lan ID is provided, for interface type i-lan. For example, 1 represents i-lan ID.

Chapter 45 MLDv2 27

• - Displays the MLD statistics information for the specified L3 pseudowire interface in the system.

• - Displays the MLD statistics information for the specified L3 pseudowire interface identifier. This is a unique value that represents the specific interface. This value ranges from 1 to 65535 for pseudowire interface.

Note: Maximum number of pseudowire interfaces supported in the system is 100.



Example SEFOS# show ipv6 mld statistics

MLD Statistics for vlan1

Number of General queries received 0

Number of Group Specific queries received 0

Number of Group and Source Specific queries received 0

Number of Mldv1 reports received 0


Number of Mldv1 leaves received 0

Number of General queries transmitted 0

Number of Group Specific queries transmitted 0

Number of Group and Source Specific queries transmitted 0

MLD Statistics for vlan2

Number of General queries received 0

Number of Group Specific queries received 0

Number of Group and Source Specific queries received 0



Number of Mldv1 leaves received 0

Number of General queries transmitted 0

Number of Group Specific queries transmitted 0


Number of Group and Source Specific queries transmitted 0

Related Command(s) • ipv6 mld router - Enables MLD message processing and egress

routing of multicast packets on the interface.


SEFOS CLI Reference Manual, Volume 7 · 2015. 8. 14. · 8 Sun Ethernet Fabric Operating System CLI...

Documents

Transcript of SEFOS CLI Reference Manual, Volume 7 · 2015. 8. 14. · 8 Sun Ethernet Fabric Operating System CLI...