SECTIONAL DIRECTIONAL CONTROL VALVES · SDS100 2 DBT001A Simple, compact and heavy duty designed...

SECTIONAL DIRECTIONALCONTROL VALVES

SDS100

2 DBT001A

Simple, compact and heavy duty designed sectional valve from 1 to 12 sections for open and closed centre hydraulic systems.

H Fitted with a main pressure relief valve and a load check valve on every working section

H Available with parallel, tandem or series circuit.

H Optional carry--over port.

H A wide range of fixed setting antishock+anticavitation port valves.

H Intermediate sections for several types of circuit.

H Available manual, pneumatic, hydraulic and ON/OFF and proportional electro--hydraulic spool control kits.

H Diameter 14 mm (0.55 in) interchangeable spools.

2nd edition August 2005:

This edition supercedes all prior documents.

WARNING!

All specifications of this catalogue refer to the standard product at this date.

Walvoil, oriented to a continuous improvement, reserves the right to

discontinue, modify or revise the specifications, without notice.

WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN

INCORRECT USE OF THE PRODUCT.

Additional information

This catalogue shows the product in the most standard configurations.

Please contact Sales Dpt. for more detailed information or special request.

SDS100

3DBT001A

Contents

Configuration examples 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Working conditions 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Performance data 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Standard working sections 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Working sections with internal pilot and drain lines 63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation and maintenance 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Accessories 96. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Standard working sections

Configuration examples

1) CN standard inlet section

2) Standard working section (type P, Q....).

3) Standard working section with outlet (type RP, RQ).

Fitted with manual, pneumatic, proportional hydraulic and ON/OFF solenoid control.

Working sections with internal pilot and drain linesThey need inlet section with pressure reducing valve and outlet section with backpressure valve.

They are prearranged for double side proportional electro--hydraulic control but it’s possible to mount manual and mechanical control

using sections with pilot through and drain

1) CRV inlet section with pressure reducing valve, relief valve, pilot lines on both sides, drain prearrangement, pressure reduced

line prearrangement

2) Working sections (type PE, QE....) with double side electro--hydraulic control

3) Double side electro--hydraulic control working sectrion with optional outlet (type RPE, RQE), pilot lines on both side and backpres

sure valve

4) Working section (type PA, QA....) with mechanical control and pilot through and drain.

5) Mechanical control working section with optional outlet (type RPA, RQA), O--ring seats for pilot throgh line closing, backpressure

valve

SDS100

4 DBT001A

Working conditions

Standard thread

SDS100

5DBT001A

This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm2/s -- 46 cSt viscosity at 40°C -- 104°F

temperature.

Nominal flow rating 60 l/min 16 US gpm

Operating pressure (max.) 315 bar 4600 psi

Back pressure (max.) on outlet port T 10 bar 145 psi

Internal leakage A(B)→T ∆p=100 bar -- 1450 psi fluid and valve at 40°C 5 cm3/min 0.31 in3/min

Fluid Mineral based oil

Fluid temperature with NBR (BUNA--N) seals from --20° to 80°C from --4° to 176°F

with FPM (VITON) seals from --20° to 100°C from --4° to 212°F

Viscosity operating range from 15 to 75 mm2/s from 15 to 75 cSt

min. 12 mm2/s 12 cSt

max. 400 mm2/s 400 cSt

Max level of contamination --/19/16 -- ISO 4406 NAS 1638 -- class 10

Ambient temperaturewith mechanical, pneumatic and hydraulic devices from --40° to 60°C from --40° to 140°F

Ambient temperaturewith electric devices from --20° to 60°C from --4° to 140°F

Tie rods tightening torque(wrench 17) 35 Nm 26 lbft

NOTE -- For different conditions please contact Sales Dept.

REFERENCE STANDARDS

BSP UN--UNF NPTF

THREADACCORDING TO

ISO 228/1 ISO 263 ANSI B1.20.3ACCORDING TO BS 2779 ANSI B1.1 unified

CAVITYACCORDING TO

ISO 1179 11926ACCORDING TO SAE J1926 J476a

DIN 3852--2shape X or Y

PORTS THREAD

MAIN PORTS BSP UN--UNF

Inlet P and carry--over C G 1/2 7/8--14 (SAE 10)

Ports A and B G 3/8 3/4--16 (SAE 8)

Outlet T G 1/2 7/8--14 (SAE 10)

Pilot V and drain L G 1/4 9/16--18 (SAE 6)

CONTROLS PILOT PORTS

Pneumatics NPTF 1/8--27 NPTF 1/8--27

Hydraulics G 1/4 7/16--20 (SAE 4)

0

5

10

15

0 10 20 30 40 50 60 70

0

10

20

30

0 10 20 30 40 50 60 70

0

10

20

30

40

0 10 20 30 40 50 60 70

Work port to outlet

Inlet to work port

Open centre

Performance data (pressure drop vs. flow)

FlowP

ress

ure

(l/min)

(bar)

From upper inlet to upper outlet.

From upper inlet to A port (spool in position 1) or B port (spool in position 2).

From A port (spool in position 2) or B port (spool in position 1) to side outlet.

Flow

Pre

ssur

e

(l/min)

(bar)

Flow

Pre

ssur

e

(l/min)

(bar)

NOTA -- Rilevate con cursore tipo 101.

2 sections

6 sections

10 sections

P→A6(B6)

P→A1(B1)

A6(B6)→T

A1(B1)→T

A1

B1

P

T

A10

B10

A1

B1

P

T

A10

B10

A1

B1

P

T

A10

B10

P→A10(B10)

A10(B10)→T

450

300

150

(psi)

300

200

100

(psi)400

150

100

50

200

4 8 12 (US gpm)16

4 8 12 16

4 8 12 16

(US gpm)

(US gpm)

(psi)

SDS100

6 DBT001A

SDS100

7DBT001A

Contents

Dimensional data 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic circuit 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ordering codes 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inlet and outlet section

ordering codes 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

section body kit and hydraulic circuit 15. . . . . . . . . . . . . .

inlet relief options 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

inlet valve options 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Working section

ordering codes 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


spools 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

“A” side spool positioners 31. . . . . . . . . . . . . . . . . . . . . . . .

“B” side options 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

complete controls 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

port valves 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Intermediate section

with service relief valve 56. . . . . . . . . . . . . . . . . . . . . . . . . .

mid return manifold section 57. . . . . . . . . . . . . . . . . . . . . .

Working section with optional outlet

ordering codes 58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


circuit configuration 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Standard working section

Dimensional data

WALVOILP0500001111020000Ref............

MADE IN ITALY

Production batch :P05 = production year (2005)00001 = progressive number

26.5 39 36 25

9.5 F

E

9.5

89

108

1111

54

86

130

30

54

36.5

220.

5

23.5

51

95.5

130

18

18

0

1

2

∅8.

5

22.5 42.5 14

6.5

WALVOILP0400001111020000Ref.............

MADE IN ITALY

Customer reference

Carry--over

0.37

3.50

0.37

4.25

8.68

1.04 1.54 1.42 0.98

1.18

2.13

1.44

0.43

0.43

2.13

3.39

5.12

5.12

0.89 1.67 0.55

0.93

2.01

3.76 0.26

∅0.

33

Code

SDS100

8 DBT001A

TYPEE F Weight

TYPEE F Weight

TYPEmm in mm in kg lb


SDS100/1 127.2 5.01 106.5 4.19 8.1 17.9 SDS100/6 307.2 12.09 286.5 11.28 23.3 51.4

SDS100/2 163.2 6.43 142.5 5.61 11 24.3 SDS100/7 343.2 13.51 322.5 12.70 26.2 57.8

SDS100/3 199.2 7.84 178.5 7.03 13.9 30.6 SDS100/8 379.2 14.93 358.5 14.11 29.1 64.2

SDS100/4 235.2 9.26 214.5 8.44 16.8 37 SDS100/9 415.2 16.35 394.5 15.53 32 70.5

SDS100/5 271.2 10.68 250.5 9.86 20.4 45 SDS100/10 551.2 21.7 430.5 16.95 34.9 76.9

Parallel circuit

Hydraulic circuit

The following pictures show the directional valve with upper inlet and outlet and mechanical control.

Main relief valve

Type R working sectionwith optional outlet

“B” sidelever kit

CN type inlet andoutlet section

“A” side positioner

Q type working section

Spool

Outlet line

Pressure line

“A” port line

Outlet line

“B” port line

Pressure line

Flow through line

C

CC -- C

A

B

Description example:

SDS100/2/CN(TVG3--175)/Q--101--8L/RQ--101--8L--F--SAE

T

A1P B1 A2 B2

175


SDS100/2/CN(TVG3--175)/Q--101--8L/RQ--101--8L--AEK--SAE

T

A1P B1 A2 B2

175

Open centre circuit Closed center circuit

2550 2550

SDS100

9DBT001A

Tandem circuit

Hydraulic circuit


SDS100/2/CN(TVG3--175)/Q--101--8L/SQ--101--8L/...--SAE

T

A1P B1

175

A2 B2


SDS100/2/CN(TVG3--175)/QR--101--8L/RQS--101--8L--F--SAE

T

P

175

A2 B2

On standard working section

On working section with optional outlet

Special QR or PR section upstream the optional outlet section is required (see page 24).

A1 B1

2550

2550

SDS100

10 DBT001A

Series circuit

Hydraulic circuit

Obtainable with a parallel section with a series spool 1S01 or 2S01 (see page 28) and a series--parallel (tandem) section down-

stream.

On standard working section

On working section with optional outlet

Obtainable with a QR or PR section (see page 24) with a series spool 1S01 or 2S01 (see page 28) and a optional outlet section with

series--parallel (tandem) circuit downstream.


SDS100/2/CN(TVG3--175)/Q--1S01--8L/SQ--101--8L/...SAE

T

A1P B1

175

A2 B2


SDS100/2/CN(TVG3--175)/QR--1S01--8L/RQS--101--8L--F--SAE

T

P

175

A2 B2A1 B1

2550

2550

SDS100

11DBT001A

SDS100

12 DBT001A

zzrzzrCodici di ordinazione

1.

SDS100 / 3 / CN(TVG3--175) / Q--101--8L / EI2(TG3--125) / Q--101--8L / RQ--101--8L--F--SAE*

2. 4.

Ordering codes4.

last section

nr. of workingsections

Description example for standard configuration:

1st section

4.1.

2.

3.

3.

2.

5.

2.

2. Complete working section* page 20

1. Complete inlet section* page 14TYPE CODE DESCRIPTIONCN(TVG3--175) 610205007 Section with upper inlet and outlet

and pressure relief valveCN(SV) 610205008 Section with upper inlet and outlet

and valve seat plugged

TYPE CODE DESCRIPTIONQ--101--8L 610155001 Parallel circuit, double acting spool

with spring return and lever controlP--101--8L.UTUT 610105005 As previous with port valves

prearrangementSQ--101--8L 610125013 Tandem circuit, double acting spool

with spring return and lever controlQR--101--8L 610155007 As previous to be couple with RQS

or RPS sectionsSP--101--8L.UTUT 610125015 Tandem circuit, double acting spool

with spring return, lever control andport valves prearrangement

PR--101--8L.UTUT 610105009 As previous to be couple with RQSor RPS sections

3. Intermediate section* page 56TYPE CODE DESCRIPTIONEI2(TVG3) 610425135 With direct service pressure relief valve

and auxiliary inlet

5. Assembling kitCODE DIRECTIONAL VALVE5TIR110123 Tie rod kit for 1 section valve5TIR110160 Tie rod kit for 2 sections valve5TIR110195 Tie rod kit for 3 sections valve5TIR110235 Tie rod kit for 4 sections valve5TIR110267 Tie rod kit for 5 sections valve5TIR110304 Tie rod kit for 6 sections valve5TIR110340 Tie rod kit for 7 sections valve5TIR110375 Tie rod kit for 8 sections valve5TIR110411 Tie rod kit for 9 sections valve5TIR110449 Tie rod kit for10 sections valve

4. Section with optional outlet* page 58TYPE CODE DESCRIPTIONRQ--101--8L--F 610355001 Parallel circuitRP--101--8L.UTUT--F 610305003 Parallel circuit with port valves

prearrangementRQ--101--8L--AE 610355002 Parallel circuit with carry--overRP--101--8L.UTUT--AE 610305004 Parallel circuit with port valves

prearrangement and carry--overRQS--101--8L--F 610325001 Tandem circuitRPS--101--8L.UTUT--F 610325002 Tandem circuit with port valves

prearrangement

NOTE (*) --Items are referred to UN- UNF threads.

SDS100

13DBT001A

zzrzzrCodici di ordinazione Ordering codes

1.

SDS100 / 2 / CN(TVG3--175) / Q--101--8L / CS1 / Q--101--8L / BN(TVG3--175)--SAE*

2. 8.nr. of workingsections

Description example for configuration with 2 inlet section and mid return manifold:

6. 7.

8.1.

2.

6.

7.

9.

6. Return manifold* pag. 57TYPE CODE DESCRIPTIONCS1 610405010 Mid return manifold

7. Complete rught inlet working section*TYPE CODE DESCRIPTIONED--Q--101--8L 610155002 Parallel circuit, double acting

spool with spring return and levercontrol

ED--P--101--8L.UTUT 610105006 As previous with port valvesprearrangement

ED--SQ--101--8L 610125017 Tandem circuit, double actingspool with spring return and levercontrol

ED--SP--101--8L.UTUT 610125018 As previous with port valvesprearrangement

8. Complete right inlet section*TYPE CODE DESCRIPTIONBN(TVG3--175) 610205009 Section with upper inlet and outlet

and pressure relief valveBN(SV) 610205010 Section with upper inlet and outlet

and valve seat plugged

9. Assembling kit with for valve with CS1CODE DIRECTIONAL VALVE5TIR110215 Tie rod kit for 2 section valve + manifold5TIR110252 Tie rod kit for 3 section valve + manifold5TIR110289 Tie rod kit for 4 section valve + manifold5TIR110323 Tie rod kit for 5 section valve + manifold5TIR110359 Tie rod kit for 6 section valve + manifold5TIR110397 Tie rod kit for 7 section valve + manifold5TIR110431 Tie rod kit for 8 section valve + manifold5TIR110467 Tie rod kit for 9 section valve + manifold5TIR110503 Tie rod kit for 10 section valve + manifold

NOTE (*) --Items are referred to UN- UNF thread; sections and covers for right inlet are different from the standard (see ref. 1 e 2)because of different components assembling


3.

2.

1.

fe: SDS100 / CN (TVG3 -- 175) ELT--12VDC -- SAE *

1. 2. 3.

Pressure relief valve setting in bar

NOTE (*) -- Items are referred to UN- UNF thread.


3. Inlet valve options page 18

2. Inlet relief options page 17

1. Section body * page 15

Standard setting is referred to 10 l/min flow.TYPE CODE DESCRIPTIONVMD100/1: direct pressure relief valve type T (standard)(TVG2--80) X196121081 Range 63 to 100 bar / 900 to 1450 psi

standard setting 80 bar / 1160 psi(TVG3--175) X196121176 Range 100 to 200 bar / 1450 to 2900 psi


standard setting 220 bar / 3200 psi

SV XTAP526360 Pressure relief valve blanking plug

TYPE CODE DESCRIPTIONCN 3FIA107700 Standard configurationCNM 3FIA107701 With pressure gauge prearrangementCNL 3FIA107704 With side inlet

TYPE CODE DESCRIPTIONELN 5CAR407330 12 VDC solenoid operated unloader

valve5CAR407331 As previous 24 VDC

ELT 5CAR407320 12 VDC solenoid operated unloadervalve with “push and twist” emergencypush--button

5CAR407325 As previous 24 VDCSV XTAP526360 Valve blanking plug:

in valve description the word SV mustbe omitted because standard

SDS100

14 DBT001A

57

23.5

51

95.5

2.24

0.93

2.01

3.76

108

130

11∅ 8.5∅ 0.33

4.25

5.12

0.43

CN standard configuration

T

P

175


CN(TVG3--175)--SAE

Directional controlvalve mounting face

Overpressure reliefvalve (pag. 17)

899.5

P T2126

.5

P T

C C

C -- C

0.37 3.50

1.04

0.83

2550

Section body and hydraulic circuit


SAE10no 2 ports

SDS100

15DBT001A

CNM configuration: with pressure gauge prearrangement

Description example: CNM(TVG3--175)--SAE

P T

100

T

P

175

MPort G1/4 plugged

Allen wrench 624 Nm / 17.7 lbft

M

3.94

2550

Section body and hydraulic circuit


58.5

P1

T

P

175

P1

Description example: CNL(TVG3--175).......--PA--SAE

TP

CNL configuration: with side inlet arrangement

2.30

2550

Port SAE10 pluggedAllen wrench 824 Nm / 17.7 lbft

SDS100

16 DBT001A

Cap code:3COP124180

0

100

200

300

400

0 10 20 30 40 50 60 700

100

200

300

400

0 10 20 30 40 50 60 70

Spring nr. 2 (green band)

Flow

Pre

ssur

e

(l/min)

(bar)

Direct presure relief valve

Inlet relief options

Spring nr. 3 (blue band)

Flow

Pre

ssur

e

(l/min)

(bar)

0,26”TIME RESPONSE

10%

175

bar90%

95%

105%

Pre

ssur

e

Time (”)

(% ∆P)

Time response

VMD100 ( TV G 3 -- 175 )

Pressure setting in bar (for standard value see page 8)

Performance data

Adjustment type

Adjustment type (G, Z)

Adjustable spring type (2, 3, 4).

G: with screw Z: with tamper proof cap

SV: relief valve blanking plug

Allen wrench 5

Wrench 19 -- 24 Nm / 17.7 lbft

Wrench 24


max. 42 45

Allen wrench 842 Nm / 31 lbft

0

100

200

300

400

0 10 20 30 40 50 60 70

Spring nr. 4 (red band)

Flow

Pre

ssur

e

(l/min)

(bar)

max. 1.65

(psi)

4500

3000

1500

(psi)

4500

3000

1500

(psi)

4500

3000

1500

1.77

2550

psi

4 8 12 16 (US gpm) 4 8 12 16 (US gpm) 4 8 12 16 (US gpm)

SDS100

17DBT001A

Emergency with push button and spring return; for detent

position turn the button after press it.

: the manual override option is intended for

emergency use, not for continuous duty operation.


CN(TVG3--175)ELT--12VDC--SAE

T

P

175

0

5

10

15

20

0 20 40 60

Pressure drop curve

Flow

Pre

ssur

e

(l/min)

(bar)(psi)

4500

3000

1500

Solenoid operated unloader valves

Operatimg featuresVALVEInternal leakage (excited position) :75 cm3/min at 100 bar / 4.45 in3/min at 1450 psiCOILDepending on model: see following features

83.5

Wrench 27 -- 24 Nm / 17.7 lbftPush--buttonfor emergency

ELT configurationELN configuration

T

P

175


CN(TVG3--175)ELN--12VDC--SAE

Without emergency push--button

3.29

25502550

Inlet valve options

5 10 15 (US gpm)

62.5


2.46

SDS100

18 DBT001A

Inlet valve options

Solenoid operated unloader valves

Nom. voltage tolerance : ±10%.Power rating : 22 W. . . . . . . . . .Nominal current : 1.76 A -- 12 VDC. . . . . . . .

: 0.9 A -- 24VDCCoil insulance : Classe H. . . . . . . . .Weather protection : IP67. . . . .Duty : 100%. . . . . . . . . . . . . . . . .NOTE: circuit with diode

Coil with Deutsch DT connector


: 0.81 A -- 24VDCCoil insulance : Classe F. . . . . . . . .Weather protection : IP65. . . . .Duty : 100%. . . . . . . . . . . . . . . . .

Coil with ISO4400 connection

connector side


: 0.74 A -- 24VDCCoil insulance : Classe F. . . . . . . . .Weather protection : IP65. . . . .Duty : 100%. . . . . . . . . . . . . . . . .NOTE: circuit with or without diode

Coil with AMP JPT connector

connector side connector side

SDS100

19DBT001A

COILS CODE

CONNECTION TYPE

ISO4400AMP JPT

Deutsch DTVoltage

ISO4400senza diodo con diodo

Deutsch DT

12 VDC 2X4311012 2X4311015 2X4311212 2X4311412

24 VDC 2X4311024 2X4311025 2X4311224 2x4311424

SDS100

20 DBT001A

Working section9.

Port valve setting in bar

1.

el: SDS100 / Q -- 101 -- 8 L -- SAE*

2. 3. 4. 6.


el: SDS100 / Q -- I112 -- 8IM -- SAE*

5.

I

4.

1.

2.

8IM

8ES3

3.

6.

6.

el: SDS100 / P --101 -- 8 L . U100 U100 -- SAE*

1.

1.

el: SDS100 / Q -- S112 -- 8ES3--12VDC -- SAE*

5.

1. Working sections kit* page 22Include body, seals, rings and load check valve.TYPE CODE DESCRIPTIONQ 5EL1077010 Parallel circuit without port valves

prearrangementP 5EL1077000 Parallel circuit with port valves

prearrangementSQ 5EL3077010 Tandem circuit without port valves

prearrangementQR 5EL1577090 As previous for section type RQS or RPSSP 5EL3077000 Tandem circuit with port valves

prearrangementPR 5EL1577095 As previous for section type RQS or RPSSections kit for special spoolsQ5 5EL1077210 Parallel circuit and floating prearrangement:

for spool type 501P5 5EL1077200 As previous with port valves prearrangement:

for spool type 501


SDS100

21DBT001A

5. Complete controls page 48They need particular sections or spools, please see the related page.TYPE CODE DESCRIPTION8ES ---- ON/OFF electric control kit: available

single or double acting operation8IM 5IDR207700 Proportional hydraulic control13IM 5IDR207750 4 positions proportional hydraulic control

6. Port valves page 54

4. “B” side options page 41

10.Working section

TYPE CODE DESCRIPTIONC 5KIT410000 Anticavitation valveUT XTAP522440 Port valve blanking plugFixed setting antishock with prefill valveU025 5KIT330025 Setting 25 bar / 360 psiU030 5KIT330030 Setting 30 bar / 430 psiU040 5KIT330040 Setting 40 bar / 580 psiU050 5KIT330050 Setting 50 bar / 725 psiU063 5KIT330063 Setting 63 bar / 900 psiU080 5KIT330080 Setting 80 bar / 1150 psiU100 5KIT330100 Setting 100 bar / 1450 psiU110 5KIT330110 Setting 110 bar / 1600 psiU125 5KIT330125 Setting 125 bar / 1800 psiU140 5KIT330140 Setting 140 bar / 2050 psiU150 5KIT330150 Setting 150 bar / 2180 psiU160 5KIT330160 Setting 160 bar / 2300 psiU175 5KIT330175 Setting 175 bar / 2550 psiU190 5KIT330190 Setting 190 bar / 2750 psiU200 5KIT330200 Setting 203 bar / 2900 psiU210 5KIT330210 Setting 210 bar / 3050 psiU220 5KIT330220 Setting 220 bar / 3200 psiU230 5KIT330230 Setting 230 bar / 3350 psiU240 5KIT330240 Setting 240 bar / 3500 psiU250 5KIT330250 Setting 250 bar / 3600 psiU260 5KIT330260 Setting 260 bar / 3750 psiU270 5KIT330270 Setting 270 bar / 3900 psiU280 5KIT330280 Setting 280 bar / 4050 psiU290 5KIT330290 Setting 290 bar / 4200 psiU300 5KIT330300 Setting 300 bar / 4350 psiU310 5KIT330310 Setting 310 bar / 4500 psiU320 5KIT330320 Setting 320 bar / 4650 psiU340 5KIT330340 Setting 340 bar / 4950 psiSetting is referred to 10 l/min -- 2.6 US gpm flow.

TYPE CODE DESCRIPTIONL 5LEV107000 Standard lever boxLF1 5LEV107100 Lever box with adjustable flow limiter in pos.1LB3 5LEV307000 Steel lever box, heavy duty typeSLP 5COP107010 Without lever box, with dust--proof plateSLC 5COP207000 Without lever box, with endcap.LCA1--4 5CLO207010 Joystick lever for 2 sections operation:

configurations type 1 and 4LCA2--3 5CLO207011 Joystick lever for 2 sections operation:

configurations type 1 and 4TK 5COP307100 Type SLP with solenoid spool lock device,

needs special spools: see page 46

3. “A” side spool positioners page 31

2. Spools page 25If not specified otherwise, the spool are from 20 to 40 l/min (5.3 to 10.5US gpm) flowTYPE CODE DESCRIPTION102 3CU6210110 Double acting, 3 positions, with A and B closed

in neutral position; for flow up to 20 l/min (5.3US gpm)

101 3CU6210100 As previous, from 20 to 40 l/min flow (5.3 to10.5 US gpm)

109 3CU6210202 As previous, from 40 to 60 l/min flow (10.5 to16 US gpm)

201 3CU6225130 Double acting, 3 positions, with A and B opento tank in neutral position

2H01 3CU6225100 Double acting, 3 positions, with A and Bpartially open to tank in neutral position

1S02 3CU6212100 Double acting, 3 positions, with A and B closedin neutral position, for series circuit

2S01 3CU6226130 Double acting, 3 positions, with A and B opento tank in neutral position, for series circuit

301 3CU6231100 Single acting in A, 3 positions, B plugged:needs G3/8 plug

401 3CU6235100 Single acting in B, 3 positions, A plugged:needs G3/8 plug

Specials spools for standard positioners kit page 29. . . . . . . . . . . . . . .801 3CU6242100 Double acting, 3 positions, regenerative in 2nd

positions with spool outSpecials spools for particular positioners kit pag. 30. . . . . . . . . . . . . .501 3CU6242100 Double acting, 4 positions, floating in 4th

positions with spool in

TYPE CODE DESCRIPTION7FTN 5V07407010 With friction and neutral position sensor8 5V08107000 With spring return in neutral position8D 5V08107200 As type 8 and pin with M6 female thread for

dual control8F2 5V08107100 With spring return in neutral position and

adjustable flow limiter8TL 5V08107310 As type 8 and pin control for flexible cable

operation9B 5V09207000 With detent in position 1 and spring return

in neutral position10B 5V10207000 With detent in position 2 and spring return

in neutral position11B 5V11207000 With detent in position 1 and 2, spring

return in neutral position8K 5V08707112 As type 8 with 12 VDC spool solenoid lock

5V08707124 As type 8 with 24 VDC spool solenoid lock8RM2 5V08107590 With spring return in neutral position and

12VDC electromagnetic detent in pos. 25V08107591 As previous, 24VDC

8MG3(NO) 5V08107660 With spring return in neutral position andoperation with microswitch in pos. 1 and 2

8PP 5V08107700 Proportional pneumatic kit8EP3 5V08107735 ON/OFF 12 VDC electro--pneumatic kit

5V08107740 ON/OFF 24 VDC electro--pneumatic kitParticular positioners kit for special spools page 39. . . . . . . . . . . . . . .13 5V13307000 4 positions with spring return in neutral,

detent in 4th position: for spool type 50113F 5V13507000 4 positions with spring return in neutral:

for spool type 501

I Optional handleversTYPE CODE DESCRIPTIONAL01/M10x150 170012015 For L lever box: H= 150 mm / 5.91 inAL08/M12x150 170013115 For joystick LCB: H = 150 mm / 5.91 in

Section kit and hydraulic circuit

Working section

A B

A B

Section type Q without port valves prearrangement

13095

.511

Section type P with port valves prearrangement


102

51

Parallel or tandem circuits are available: for series circuit see page 10.

All sections can be fitted with or without port valves prearrangement.


SAE8n.2 threads A B

A B

Parallel circuit

36

Port valve(page 54)

“A” side spool positioner (page 31) “B” side option (page 41)

1.42 0.43

5.12

2.01

3.76 4.

02

SDS100

22 DBT001A

A B


Working section

Section type SQ without port valves prearrangement

Section type SP with port valves prearrangement

A B

A B

A B

Tandem circuit

Dimensions are the same of parallel circuit section.

SDS100

23DBT001A

A B

A B


Working section

Section type QR without port valves prearrangement

Section type PR with port valves prearrangement

Special circuit

Used to get series and tandem circuits with RQS or SQS optional outlet sections (see pages 10 and 60); dimensions are the same

as parallel section.

A B

A B

SDS100

24 DBT001A

stroke -- 6.5 mm-- 0.26 in

0

10

20

30

40

50

0 1 2 3 4 5 6 70

10

20

30

40

50

0 1 2 3 4 5 6 7

F

J

Y

P(on ports) = 63 bar / 900 psiP(on ports) = 100 bar / 1450 psiP(on ports) = 250 bar / 2900 psi

Qin = 40 l/min / 10.6 US gpm

Type 101

Spools

Flo

w

Stroke (mm)

(l/min )

Flo

w

Stroke

Spool metering A(B)→TSpool metering P→A(B)

(mm)

(l/min )

201

201

201A B

P T

A

" stroke + 6.5 mm+ 0.26 in

Performance data

A B

P T

A B

P T

FJY

FJ

Y

P--A--B--T closed, with flow through line (LC) open

P → A B → T

P→ B A → T

A B

T

P PLC

T

A B

T

P PLC

T

A B

T

P PLC

T

From 20 l/min (5.3 US gpm) to 40 l/min (10.6 US gpm) flow.

(in)0.1 0.2 (in)0.1 0.2

4

8

12

(US gpm)

4

8

12

(US gpm)

SDS100

25DBT001A

F

J

Y



0

10

20

30

0 1 2 3 4 5 6 7

0

20

40

60

80

0 1 2 3 4 5 6 7

A B

T

P PLC

T

A B

T

P PLC

T

201A B

P T

201A B

P T


Type 102

Spools

Type 109


0

10

20

30

0 1 2 3 4 5 6 7

Flo

w

Stroke (mm)

(l/min )

Flo

w

Stroke


(mm)

(l/min )

Performance data

FJ

Y

F J

Y

0

20

40

60

80

0 1 2 3 4 5 6 7

Flo

w

Stroke (mm)

(l/min )

Flo

w

Stroke


(mm)

(l/min )

Performance data

F

J Y

F J

Y

From 40 to 60 l/min flow.

Up to 20 l/min flow.

(in)0.1 0.2 (in)0.1 0.2

(in)0.1 0.2(in)0.1 0.2

F

J

Y



2

4

6

(US gpm)

2

4

6

(US gpm)

5

10

15

(US gpm)20

5

10

15

(US gpm)20

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in

SDS100

26 DBT001A

Type 201

A B

T

P PLC

T

P closed, A--B to tank, with flow through line (LC) open

A B

P T

201

Spools

Type 301

P--A--B closed, with flow through line (LC) open

A B

P T

201

Type 401

A B

P T

201

P--A--B closed, with flow through line (LC) open

A

T P PLCT

B

T P PLCT

Plug SAE8Allen wrench 6 -- 24 Nm / 17.7 lbft

Plug SAE8Allen wrench 6 -- 24 Nm / 17.7 lbft

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in

SDS100

27DBT001A

Spool meteringQin = 40 l/min -- 10.6 US gpm / P(on ports) = 100 bar -- 1450 psi

0

20

40

60

0 10 20 30 40 500

10

20

30

40

50

0 1 2 3 4 5 6 7

Pre

ssur

e

Flow (l/min)

(bar)

Flo

w

Stroke

Pressure drop on series connection

(mm)

(l/min )

A1→A2

201A B

P T


A B

T

P PLC

T

Type 1S02

Spools

Performance data

Type 2S01

201A B

P T

P closed, A--B to tank, with flow through line (LC) open

A B

T

P PLC

T

P→A(B)

A(B)→T

(in)0.1 0.2

(psi)

720

480

2404

8

12(US gpm)

4 8 12 (US gpm)

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in

SDS100

28 DBT001A

stroke -- 6.5 mm-- 0.26 in

A

" stroke + 6.5 mm+ 0.26 in

0

20

40

60

0 10 20 30 40 50

Pre

ssur

e

Flow (l/min)

(bar)

Pressure drop in position 2(last section)

201A B

P T

201A B

P T

0

10

20

30

40

50

0 1 2 3 4 5 6 7

Type 801

Spools

Flo

w

Stroke

Spool metering

Qin = 40 l/min -- 10.6 US gpm / P(on ports) = 100 bar -- 1450 psi

(mm)

(l/min )

Performance data


P → A B → T

P+B → A (regenerative)

A B

T

P PLC

T

A B

T

P PLC

T

A B

T

P PLC

T

201A B

P T

B→AP→A B→TP→A

(in)0.1 0.2

(psi)

720

480

2404

8

12

(US gpm)4 8 12 (US gpm)

SDS100

29DBT001A

0

50

100

150

0 10 20 30 40 50

Pre

ssur

e

Flow (l/min)

(bar)


B→TA→T

Spool meteringQin = 40 l/min -- 10.6 US gpm / P(on ports) = 100 bar -- 1450 psi

0

10

20

30

40

50

0 1 2 3 4 5 6

Flo

w

Stroke (mm)

(l/min)

P→A

A→T

201A B

P T

3

A--B → T (floating)

Type 501

Spools

Performance data

Q5 -- P5 section or RQ5 -- RP5 optional outlet section required, contact Sales Dpt. for further information.

To be combined with 13 or 13F spool positioners (see page 39).

P →B A → T

P → A B → T

P--A--B--T closedflow through line (LC) open

201A B

P T

3

201A B

P T

3

201A B

P T

3

AA

P→B

B→T

"

stroke -- 6 mm / -- 0.24 in

A

stroke -- 10.5 mm / -- 0.41 in

(in)0.1 0.2

(psi)

1500

1000

500

2000

4

8

12(US gpm)

4 8 12 (US gpm)

stroke + 6 mm / + 0.24 in

A B

T

P PLC

T

A B

T

P PLC

T

A B

T

P PLC

T

A B

T

P PLC

T

SDS100

30 DBT001A

Spring return in neutral position

”A” side spool positioners

It’s standard configured with spring type B (see diagram); it’s also available with heavier springs type C (8MC codice: 5V08207000)

or type D (8MD codice: 5V08307000).

201

Type 8

36.5

Allen wrench 46.6 Nm / 4.9 lbft


0

50

100

150

200

0 1 2 3 4 5 6 7Stroke

For

ce

(l/min)

(N)

Force--stroke diagram(curve is the same for either ports)

BCD

With friction type 7FTN

201

36.5

46

M6

11

12


Wrench 99.8 Nm / 7.2 lbft

Type 8D

201

1.44

30

20

10

40(lbf)

(in)0.1 0.2

1.44

1.81

0.47

0.43

88.3 max

Wrench 30manual tightening


Allen wrench 8Alle wrench 49.8 Nm / 7.2 lbft

3.48 max.

SDS100

31DBT001A

“A” side spool positioners

Spring return in neutral position

201

36.5

54.5

M8

Allen wrench 4 -- 6.6 Nm / 4.9 lbft



Type 8F2

With spool stroke adjustment in position 2 (P→B).

Allen wrench 4

1.44

2.15

Flexible cable type CDwith fixed end

201

Type 8TL

33

53.5

62

8


24 Nm17.7 lbft

15∅

For connect the kit 8TL to flexible cable always ask the following kits:

-- type CP50 code 5TEL405005, with fixed cap for CG cables with revolving end.

-- type TQ50 code 5TEL105110, with revolving cap for CD cables with fixed end.

9H8∅

1.30

2.11

2.44

0.31

0.59

∅

0.35∅

111 114

Flexible cable type CGwith revolving end

Positioner type 8TL with kit CP50 Positioner type 8TL with kit TQ50


Wrench 2424 Nm / 17.7 lbft

Wrench 10 -- 9.8 Nm / 7.2 lbft

4.37




4.49

SDS100

32 DBT001A

2 0 1Port B Port A

0

50

100

150

200

--7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6 7Stroke

For

ce

(mm)

(N)

0

50

100

150

200

--7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6 7Stroke

For

ce

(mm)

(N)

0

50

100

150

200

--7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6 7

With detent and spring return to neutral position from either directions


Type 9B

Type 10B

Type 11B

201

201

201

Stroke

For

ce

(mm)

(N)

Unlocking force from position 1: 160 N ±10 N / 36 lbf ±2.2 lbf

72.5



Force--stroke diagram

2 0 1Port B Port A

Detent area


2 0 1Port B Port A


Unlocking force from position 2: 160 N ±10 N / 36 lbf ±2.2 lbf

Unlocking force from positions 1 and 2: 160 N ±10 N / 36 lbf ±2.2 lbf

Detent area

Detent area Detent area

(in)0.1 0.2--0.1--0.2 0

30

20

10

40(lbf)

(in)0.1 0.2--0.1--0.2 0

30

20

10

40(lbf)

(in)0.1 0.2--0.1--0.2 0

30

20

10

40(lbf)

2.85

72.5



2.85

72.5



2.85

SDS100

33DBT001A

108

104

Solenoid kit with connector



Notch 1.2mm / 0.047 in6.6 Nm / 4.9 lbft

4.09

4.25

Electromagnetic detent type 8RM2


With electromagnetic detent in position 2 and spring return to neutral position.

Operating featuresCOILNominal voltage : 12 / 24 VDC ± 10%. . . . . . . . . . . . . . .Power rating : 5.5 W. . . . . . . . . . . . . . . . . .Resistance (20 °C / 68 °F) : 26.5 / 105 Ohm. . . . . . .Min unlocking force : 45 N / 49.5 lbf. . . . . . . . . . . . .Duty cycle : 100%. . . . . . . . . . . . . . . . . . . .

600

Coil with Deutsch DTconnection

Coil with AMP Fastin--Fastonconnection

Coil with Packard M--Packconnection

374

200

201

23.67.87

14.7

SDS100

34 DBT001A

COMPLETE CONTROLS CODE

CONNECTOR TYPE

Deutsch DT AMP Packard M--Pack

CONTROL DESCRIPTION

Voltage 8RM2 8RM2A(200) 8RM6

12 VDC 5V08107590 5V08107595 5V08107597

24 VDC 5V08107591 5V08107596 5V08107598

Needconnector(page 96)

C19 C21 C20

COILS CODE

CONNECTOR TYPE

Voltage Deutsch DT AMP Packard M--Pack

12 VDC YSOL532455 YSOL532452 YSOL532451

24 VDC YSOL532456 YSOL532458 YSOL532457

71.5

Microswitch with connector

20.5

Wrench 2242 Nm / 31 lbft




0.81

2.81

With microswitch type 8MG3(NO)


201

8MG1(NO) kit

Operating featuresMICROSWITCHMechanical life : 5x105 operations. . . . . . . . . . .Electrical life (resistive load) : 105 oper. -- 7A / 13,5VDC

: 5x104 oper -- 10A / 12VDC: 5x104 per -- 3A / 28VDC

201

201

Other configurations

8MG2(NO) kit

8MG3(NO) kit

With NO contactcode: 4MIC730

PACKARD W--PACKfemale connector withmale end

With NC contactcode: 4MIC740

PACKARD W--PACKmale connector with fe-male end

It’s possible to obtain further configurations of complete control, using the MG kit, microswitches and 3 positions “A” side spool posi-

tioner, as following draw.

Kit MG

Microswitch

3 positions “A” side spoolpositioner type 9B, 10B, 11B.

(see page 33)

Kit MG3code: 5KIT820700



More configurations and spare parts

84.5 128

36.572.5

With spring return in neutral position and microswitch operated in both directions.

Also available 8MG1(NO) configuration (microswitch operated in position 1) and 8MG2(NO) configuration (microswitch operated in

position 2); dimensions are the same of 8MG3 configuration.

Same configurations are vailable with normally closed (NC) contact.

3.33 5.04

1.442.85

SDS100

35DBT001A


Contact CONTROLS DESCRIPTION Need connectorContacttype 8MG3 8MG2 8MG1

Need connectortype

NO 5V08107660 5V08107680 5V08107670 C07 see pageNC 5V08107661 5V08107681 5V08107671 C17

see page96

22.5

76.5

84





3.01

0.893.

31

Solenoid lock device type 8K


With spring return and spool electromechanical lock in neutral position; when coil is feeded the spool can be moved.

Operating featuresACTUATORLock stroke : 3.5 mm / 0.14 in. . . . . . . . . . . . . . . . . . . . .COILDepending on model: see following features

201

Coil with ISO4400 connector


: 0.81 A -- 24VDCCoil insulance : Class F. . . . . . . . .Weather protection : IP65. . . . .Duty : 100%. . . . . . . . . . . . . . . . .







43.5

182

1.71

7.17

SDS100

36 DBT001A


CONNECTION TYPE

ISO4400 Deutsch DT Packard M--Pack

CONTROL DESCRIPTION

Voltage 8K 8K4 8K6

12 VDC 5V08707112 5V08707412 5V08707613

24 VDC 5V08707124 5V08707424 5V08707624


C02 C19 C20

COILS CODES

CONNECTOR TYPE

Voltage ISO4400 Deutsch DT Packard M--Pack

12 VDC 2X4300012 YSOL300015 YSOL300014

24 VDC 2X4300024 YSOL300026 YSOL300024

0

2

4

6

8

--7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6 7

2 0 1Port B Port A

Pilot pressure -- stroke diagram

Pilot pressure min 7 bar / 102 psi -- max 10 bar / 145 psi

Pilo

tpre

ssur

e

Stroke (mm)

(bar)

5.2

2

Metering zoneSpool overlap area

(in)0.1 0.20--0.1--0.2

60

40

20

80

(psi)

100

7587

n.2 filetti

110

67.527.5

NPT 1/8”

30

Special wrench -- 9.8 Nm / 7.2 lbftAllen wrench 46.6 Nm / 4.9 lbft


1.08 2.66

1.18

4.33

3 positions “A” side spoolpositioner type 9B, 10B, 11B.

(see page 33)

Solenoid lock device type 8K

“A” side spool positioner

More configurations and spare parts

Bobina

Kit K

Proportional pneumatic control type 8PP

201

V1 V2

40

Fitted with with actuator:code 5KIT810700

72.5

It’s possible to obtain further configurations of complete control, using the K kit, coils and 3 positions “A” side spool positioner, as

following draw: for information contact Sales Department.

2.85 1.57

SDS100

37DBT001A

Ø

110

39

Special wrench9.8 Nm / 7.2 lbft



112.

5

141

3727.5

6

1.08 1.46

4.43

1.54

4.33

5.55

Ø 0.24


ON/OFF electro--pneumatic control type 8EP3


Operating featuresCONTROLPilot pressure : 6 bar -- 87 psi. . . . . . . . . . . . . . . . . . .

(max.10 bar -- 145 psi)COILNominal voltage tolerance : ±10%. . . . . . . . .Power rating : 8 W. . . . . . . . . . . . . . . . . . . .Nominal current : 0.67 A -- 12 VDC. . . . . . . . . . . . . . . . . .

: 0.33 A -- 24VDCCoil insulance : Class H. . . . . . . . . . . . . . . . . . .Weather protection : IP65. . . . . . . . . . . . . . .Duty cycle : 100%. . . . . . . . . . . . . . . . . . . . . .

Coil with ISO6952connector

Coil with flying leads

200

Scheme ISO 1219

Scheme

201

V1 V2

201

V1 V2

7.87

Respect the tolerance value.Tightening too strongly cancause damages to the valve.


(+0 / --10%)

SDS100

38 DBT001A

COMPLETE CONTROL CODE

CONNECTION TYPE

ISO6952 Flaying leads

CONTROL TYPE

Voltage 8EP3 8EP35

12 VDC 5V08107735 5V08107736

24 VDC 5V08107740 5V08107741

Needcnnector(page 96)

C01(included) /

COILS CODE

VoltageCONNECTION TYPE

VoltageISO6952 Flaying leads *

12 VDC 2XB1010121100 2XB1010120000

24 VDC 2XB1010241100 2XB1010240000

* Several type of connectors can be wired on request

0

100

200

300

400

--11--10 --9 --8 --7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6Stroke (mm)

(N)


2 0 1Port B Port A

3Floating

(in)0.1 0.2--0.1--0.2 0--0.3--0.4

60

40

20

80(lbf)

For

ce

72.5



2.85

0

100

200

300

400

--11--10 --9 --8 --7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6Stroke

For

ce

(mm)

(N)


Detent area

Locking force (:) in position 3: 300 N ±10 N / 67.4 lbf ±2.2 lbfUnlocking force in position 3: 250 N ±10 N / 56.2 lbf ±2.2 lbf

:

2 0 1Port B Port A

3Floating

(in)0.1 0.2--0.1--0.2 0--0.3--0.4

60

40

20

80(lbf)

72.5



2.85

Positioners for special spools


Kit 13

Kit 13F

With detent in position 3 (floating) and spring return to neutral from either directions.

Available for spool type 501 (see page 30).

201 3

With additional spring in position 3 (floating) and spring return to neutral from either directions.


201 3

SDS100

39DBT001A




: 0.95 A -- 24VDCCoil insulance : Class H. . . . . . . . .Weather protection : IP65. . . . .Duty : 100%. . . . . . . . . . . . . . . . .

Coil with ISO4400 connector Coil with Deutsch DT connector Coil with Packard M--Pack connector

49

634



1.93

25

72.52.85

401.57


Positioners for special spools

With solenoid lock device

Coil

Kit K

Fitted with actuatiorcode: 5KIT810700

Several configurations are possible using 4 positions “A” side spool positioner, the K kit and one of available coils, as indicated below.

For informations contact Sales Department.



4 positions “A” side spoolpositioner type 13 and 13F.

(see page 39)

SDS100

40 DBT001A

COIL CODES

CONNECTION TYPE

Voltage ISO4400 Deutsch DT Packard M--Pack

12 VDC 2X4300012 2X4300014 YSOL300013

24 VDC 2X4300024 2X4300026 YSOL300024


C02 C19 C20

201

15 max.

Lever control

”B” side options

Zama (zinc alloy) lever pivot box with protective rubber bellow; it can be rotated 180° (configuration L180).

With spool stroke adjustment in position 1 (P→A); it can be rotated 180° (configuration LF1180).

201

14

28

30

54

79

22.5

65

1818

0

1 2

130

326 30’

Configuration L180

Horizontal handleverassembly

Vertical handleverassembly

30

53.7

79

22.5

65

1818

0

1 2

130

326 30’






Allen wrench 4

M10

M10

Type LF1

Type L

1.18

2.13

0.89

2.59 3.

11

5.12

1.10 0.

55

22.5

0.89

2.56 3.

11

5.12

2.11

1.18

0.59 max.

SDS100

41DBT001A

30

14

8

18.5

14∅ 13.5

∅

78H8∅


Mechanical control with dust--proof plate kit.

Type SLP

201

Dust--proof seal

0.55

0.73

0.31

1.18

0.53

∅

0.28

0.55∅

0.31∅


Controls arrangement

Lever control

Type LB3

Steel lever control, with pivot placed above; the particular construction makes it suitable for heavy duty applications.

It can be rotated 180° (configuration LB3180).

201

30

41

65

24

M10

15°9’ 15°9’

23°38’0

1 23

130

79

Configuration LB3180

201

Type SLC

72.5


Protection cap usable with 8PP pneumatic or 8EP3 elettro-

control

2.85

Horizontal handleverassembly

Vertical handleverassembly

0.94

2.56 3.

11

5.12

1.18

1.61

SDS100

42 DBT001A

Joystick type LCA

“B” side options

201

201

For 2 sections operation and available in two different configurations LCA1--4 e LCA2--3 for two assembling mode (see following

pages).

Pivot

1st section spool

2nd section spool Wrench 139.8 Nm / 7.2 lbft





Wrench 14

NOTE -- The handlever must be ordered separately (see page 21).

SDS100

43DBT001A

2nd spool axis1st spool axis

51

38.5

95

M12

x1,5

927

B1

A2

A1

B1--A2 B1--B2

A1--A2 A1--B2

B2

Joystick type LCA


Configuration LCA1--4

LCA1 and LCA4 configurations can be obtained by rotating the flange/fulcrum block by 180°.

Assembling mode LCA1: pivot placed down on the left

Assembling mode LCA4: pivot placed above on the right

Operation angle

Spool RSpool L

R spool operation

L spool operation

51

63.5

9 27

A2

A1

B2

B1

A2--A1A2--B1

B2--A1B2--B1

1.52

2.01

1.06 0.353.74

2.01

2.50

1.060.35

Two section operation with diagonal movement

Two section operationwith diagonal movement

SDS100

44 DBT001A

Joystick type LCA

“B” side options

Configuration LCA2--3

LCA2 and LCA3 configurations can be obtained by rotating the flange/fulcrum block by 180°.

Assembling mode LCA2: pivot placed down on the right

2nd spool axis1st spool axis 9

51

38.5

51

63.5

A1

A2

B1

B2

A1--A2 A1--B2

B1--A2 B1--B2

B2

A1

A2

B1

B2--A1B2--B1

A2--A1A2--B1

927

95

M12

x1,5

Assembling mode LCA3: pivot placed above on the left

Operation angle

Spool RSpool L

1.52

2.01

0.353.74

2.50

2.01

1.06 0.35

L spool operation

Two section operation with diagonal movement

R spool operation

Two section operationwith diagonal movement

SDS100

45DBT001A

SDS100

46 DBT001A

Spool solenoid lock device type SLK


With spring return and spool electromechanical lock in neutral position; when coil is feeded the spool can be moved.

The control kit doesn’t include the coil, that has to be ordered separately and needs special spools.

For information about other “B” side controls with electromechanical lock, contact Sales Department

Description

Double acting, 3 positions, with A and Bclosed in neutral position

Double acting, 4 positions, floating in 4th

positions with spool in: Q5 -- P5 section orRQ5 -- RP5 optional outlet section requi-red

If not specified otherwise, the spool are from 20 to 40 l/min -- 10.5 USgpm flow

Type Code

SPOOLS CODE

B102

B501

3CU6310102

3CU6342501

SLK control

Coil

3 positions “A” side spool positioners(see page 39) to couple with spool type B501

3 positions “A” side spool positioners(see page 31) to couple with spool type B102

Spool type B

YSOL300024

YSOL300014

CONNECTION TYPEVoltage ISO4400 Packard M--Pack

COILS CODE

12 VDC

24 VDC

2X4300012

2X4300024Need

connector.(page 96)

C02 C20

Deutsch DT

YSOL300015

YSOL300026

C19


Spool solenoid lock device type SLK






section SDS100 / Q--B102--8SLK--SAE

21.5

51

84



3.31

0.85

2.01



Coil with Packard M--Pack connector




43.5

182

49

184

1.93

7.24

1.71

7.17

SDS100

47DBT001A

TYPE: Q--S102--8ES3--24VDC CODE: 610155003DESCRIPTION: Parallel circuit with 3 positions double acting spool,ON/OFF solenoid controlTYPE: RQ--S102--8ES3--24VDC--F CODE: 610355003DESCRIPTION: Working section with optional outlet fitted out previousNOTE: for working sections codes with port valves prearrangementcontact Sales Department.

8ES solenoid control

Complete controls17.

Solenoid direct control with spring return to neutral position; it needs special spools and standard working section body (body kit

without seals on spool).

EL SDS100 / Q -- S102 -- 8ES3 -- 24VDC -- SAE *


3.2. 4. 5.

1.

3. SpoolTYPE CODE DESCRIPTIONS102 3CU6810102 Double acting, 3 positions with A and B closed

in neutral position

4. Control kitsTYPE CODE DESCRIPTION8ES1 5V08028 P→A, with spring return in neutral position8ES2 5V08028 P→B, with spring return in neutral position8ES3 5V08029 Double acting with spring return in neutral

position

2. Working section kit *TYPE CODE DESCRIPTIONQ/IM--ES 5EL107701A Parallel circuitP/IM--ES 5EL107700A Parallel circuit with port valves

prearrangementSQ/IM--ES 5EL307701A Tandem circuitSP/IM--ES 5EL307700A Tandem circuit with port valves

prearrangementRQ/IM--ES 5FIA20771A Section with optional outlet and parallel

circuitRP/IM--ES 5FIA20770A As previous with valves prearrangement

1. Complete working section *

2.

5. CoilsTYPE CODE DESCRIPTIONWith ISO4400 connection10.5VDC 4SOL512011 Nominal voltage 10.5VDC12VDC 4SOL512012 Nominal voltage 12VDC24VDC 4SOL512024 Nominal voltage 24VDCWith Deutsch DT connection4--10.5VDC 4SOL512111 Nominal voltage 10.5VDC4--12VDC 4SOL512112 Nominal voltage 12VDC

4.

4.

3.

4.

4. 5.

5.

NOTE (*) -- Codes are referred to UN- UNF thread.

SDS100

48 DBT001A

A B

8ES solenoid control

Complete controls

0

100

200

300

400

0 20 40 60

Operating condition diagram

Flow

Pre

ssur

e

(l/min)

(bar)

Operation area

(psi)4500

3000

1500

5 10 15 (US gpm)

201

01

8ES1 kitsingle acting on A

8ES3 kitdouble acting

20

8ES2 kitsingle acting on B

P ⇒ BA ⇒ T

P ⇒ AB ⇒ T

+--

Electric wiring example

To battery

Connector 1 Connector 2

21

21

Operating featuresCONTROLSFuga interna A(B)→T(∆p = 100 bar / T = 40°C) : 10 cm3/min -- 0.61 in3/min. . . . . . . . . .COILSNominal voltage tolerance : ±10%. . . . . . . . .Power rating : 36 W. . . . . . . . . . . . . . . . . . . .Coil insulance : class H. . . . . . . . . . . . . . . . . . .Duty cycle : 100%. . . . . . . . . . . . . . . . . . . . . .

Coil with ISO4400 con-nection (needs connectortype C02: see page. 96)

180.71

7 Nm / 5.2 lbft 88.5

x xDedicated spool

Coil with Deutsch DTconnection (needs con-nector type C19: seepage. 96)

Emergencymanual override




3.48

SDS100

49DBT001A

TYPE: Q--I112--8IM CODE: 610155004DESCRIPTION: Parallel circuit with 3 positions double acting spool,proportional hydraulic controlTYPE: RQ--I112--8IM--F CODE: 610355004DESCRIPTION: Working section with optional outlet fitted out previousNOTE: for working sections codes with port valves prearrangementcontact Sales Department.

8IM proportional hydraulic control


It needs special spools and standard working section body (body kit without seals on spool).

el: SDS100 / Q -- I112 -- 8IM -- SAE*


3.2. 4.

1.

2.

3.4.

4.

3. SpoolsTYPE CODE DESCRIPTIONI118 3CU6410118 Double acting, 3 positions, with A and B closed

in neutral position; for flow up to 20 l/min (5.3US gpm)

I112 3CU6210420 As previous for flow from 20 to 40 l/min (5.3 to10.5 US gpm)

I117 3CU6410117 As previous for flow from 40 to 60 l/min (10.5to 16 US gpm)

I203 3CU6225420 Double acting, 3 positions, with A and B opento tank in neutral position; for flow from20 to 40l/min

4. Control kit *TYPE CODE DESCRIPTION8IM 5IDR207700 Double sides proportional hydraulic control

with spring return in neutral position

2. Working section kit *TYPE CODE DESCRIPTIONQ/IM--ES 5EL107701A Parallel circuitP/IM--ES 5EL107700A Parallel circuit with port valves

prearrangementSQ/IM--ES 5EL307701A Tandem circuitSP/IM--ES 5EL307700A Tandem circuit with port valves

prearrangementRQ/IM--ES 5FIA20771A Section with optional outlet and parallel

circuitRP/IM--ES 5FIA20770A As previous with valves prearrangement



SDS100

50 DBT001A

V

P

T

A1 A2

B1 B2

VA2VA1

VB2VB1

P1 32 4

0

10

20

30

40

--7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6 7


Complete controls

46.5

19

32

VA VB


201

VA VB

Connection example

2 0 1Port B Port A

Pilo

tpre

ssur

e

Stroke (mm)

(bar)

Metering zone

Spool overlap area


26.8

Operating featuresMax pilot pressure : 70 bar / 1015 psi. . . . . . . .

VA2VA1

VB2VB1

P1 32 4

P

T

A1 A2

B1 B2

Configuration for direct connection from the directional control valveto the pilot valve.1) CR inlet section with pressure reducing valve (se page 68)2) PA or QA working section with pilot through and drain (see page 88)3) RPA or RQA optional outlet working section with pilot throgh lineclosing and backpressure valve (see page 90).

Configuration for connection to the pilot valve with external pump (seeprevious page).

SVM400 hydraulic pilot control valvewith 088 pressure control curve

(in)0.1 0.20--0.1--0.2

300

200

100

400

(psi)

500

388

1.26

1.83

0.75SAE4

SDS100

51DBT001A



It needs special spools and special working section body (body kit without seals on spool).

el: SDS100 / Q -- I501 -- 13IM -- SAE*


3.2. 4.

1.

2.

3.4.

4.

3. SpoolsTYPE CODE DESCRIPTIONI503 3CU6442000 4 positions double acting spool, floating circuit

in 4th position with spool in, for flow from 20 to40 l/min (5.3 to 10.5 US gpm).

4. Control kit *TYPE CODE DESCRIPTION13IM 5IDR207750 Double sides proportional hydraulic control

with spring return in neutral position; forfloating circuit spool

2. Working section kit *TYPE CODE DESCRIPTIONQ5/IM 5EL107721A Parallel circuitP5/IM 5EL107720A Parallel circuit with port valves

prearrangementSQ5/IM 5EL307721A Tandem circuitSP5/IM 5EL307720A Tandem circuit with port valves

prearrangementRQ5/IM 5FIA207715A Optional outlet working section, with

parallel circuitRP5/IM 5FIA207705A As previous with port valves

prearrangement



TYPE: P5--I501--13IM.UTUT CODE: 610105600DESCRIPTION: Parallel circuit with port valves prearrangement, 4positions double acting spool, floating in 4th postion with spool in,proportional hydraulic controlTYPE: RP5--I501--13IM.UTUT CODE: 610305600DESCRIPTION: Working section with optional outlet fitted out previousNOTE: for working sections codes without port valves prearrangementcontact Sales Department.

SDS100

52 DBT001A

0

10

20

30

0 2 4 6 8

8

0.85

Pressure control curve (port VA2)type 125 without step

Pilo

tpre

ssur

e

Stroke (mm)

(bar)22.5

7.6

0

10

20

30

0 2 4 6 8

6.5

0.85

Pressure control curve (port VB2)type 045 with step

Pilo

tpre

ssur

e

Stroke (mm)

(bar)

15.5

7.6

7.25

100

200

300

(psi)400

100

200

300(psi)400

225

94

0.29

0.03

0.1 0.2 (in)0.3

0.1 0.2 (in)0.3

0.03

116

326

Operating featuresMax pilot pressure : 70 bar / 1015 psi. . . . . . . .


Complete controls

P

T

A1 A2

B1 B2

VA1 VA2

VB1 VB2

SVM400 hydraulic pilotcontrol valve

Connection example

VA VB

50

23

32

SAE4


201 3

VA VB

0

10

20

30

40

--11 --10 --9 --8 --7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6


2 0 1Port B Port A

3Floating

Pilo

tpre

ssur

e

Stroke (mm)

(bar)

23.5

10.5

24

Floating zone

Metering zone

Overlap area

P

T

300

200

100

400

(psi)

500

(in)0.1 0.2--0.1--0.2 0--0.3--0.4

0.41

341

348

1.97

1.26

0.91

SDS100

53DBT001A

100

150

200

250

300

0 20 40 60

A B

T

P

A B A B

T

P

U100 UT UT U100 U100 U100

Valve on port A.Blanking plug on port B.

Valves on ports A and B.Valve on port B.Blanking plug on port A.

0

50

100

150

200

0 20 40 60200

250

300

350

400

0 20 40 60

U 100

Pressure settinga in bar.

Antishock with prefill

Port valves

Performance data

Pressure drop

0

5

10

15

20

0 20 40 60

Flow

Pre

ssur

e

(l/min)

(bar)

Flow

Pre

ssur

e

(l/min)

(bar)

Pressure / flow diagram(from 25 to 140 bar / from 360 to 2050 psi)


0.28”TIME RESPONSE

10%

115

bar90%

95%

105%

Pre

ssur

e

Time (”)

(% ∆P)

Time response

Flow

Pre

ssur

e

(l/min)

(bar)


Flow

Pre

ssur

e

(l/min)

(bar)


(psi)(psi)2400

1600

8002400

1600

3200

4000

(psi)

3200

4000

4800

5600

(psi)240

160

80 1670

psi

5 10 15 (US gpm) 5 10 15 (US gpm) 5 10 15 (US gpm)

5 10 15 (US gpm)

SDS100

54 DBT001A

0

5

10

15

20

0 20 40 60

C

A B

T

P

A B A B

T

P

Anticavitation

Port valves

Performance data

Pressure drop

Flow

Pre

ssur

e

(l/min)

(bar)

C UT UT C C C

Valve on port A.Blanking plug on port B.

Valves on ports A and B.Valve on port B.Blanking plug on port A.

Valve blanking plug


UT

A B

T

P

UT UT


(psi)240

160

80

5 10 15 (US gpm)

SDS100

55DBT001A

EI2 intermediate section

36

C

C

95.5

51

119

1131

max

.42

SAE8

3.5

P1

C -- C


SDS100/2/CN(TG3--175)/Q--101--8L/EI2(TVG3--125)/RQ--101--8L--F--SAE

SAE8 plug code 3XTAP822150*Allen wrendh 6 -- 24 Nm / 17.7 lbft

Section wirh service relief valve section and prearranged for a second inlet.

Directional controlvalve mounting face Direct pressure relief valve type: TV(G3)

Code: X196121176Wrench 27 -- 24 Nm / 17.7 lbft

Joint code XGIU527650*Wrench 27 -- 24 Nm / 17.7 lbft

T

A1P B1 A2 B2

175 125

P1

Section bodycode: 3EL4078300*

1.423.76 0.14

2.01

max

.1.6

50.

434.

691.

22

18002550

P A1

B1

A2

B2T

P1


SDS100

56 DBT001A

CS1 return manifold

3695.5

51

119

112C

C

P

T

A1

B1

A2

B2 P1

T T

C -- C

SA

E10

A2B2A1 B1

T


Plug code 3XTAP826160Allen wrench 8 -- 24 Nm / 17.7 lbft


SDS100/2/CN(TVG3--175)/Q--101--8L/CS1/Q--101--8L/BN(TVG3--175)--SAE

Mid return manifold for directional valve with left and right inlet both; they allow 2 indipendent circuits with common outlet.

Section bodycode: 3EL4078500*

P

175

P1

175

1.42

0.08

4.69

0.43

2.01

3.76

2550 2550


SDS100

57DBT001A

1. Working section kit page 59Include body, seals, rings and load check valve.TYPE CODE DESCRIPTIONRQ 5FIA207710 Parallel circuitRP 5FIA207700 Parallel circuit prearranged for port valvesRQS 5FIA207719 Tandem circuitRPS 5FIA207709 Tandem circuit prearranged for port valvesSection kits for special spoolsRQ5 5FIA207715A Parallel circuit prearranged for floating

circuit: for spool type 501RP5 5FIA207705A As previous prearranged for port valves:

for spool type 501

Section with optional outlet type R23.

fs: SDS100/ RQ -- 101 -- 8 L -- AE --SAE*

NOTA (*) -- Items are referred to UN- UNF thread.

Decription example:

2. 4.3.1.

1.

2.

3.

4.

2. Spools page 25

3. “A” side spool positioners page 31

4. “B” side options page 41

6. Port valves page 54

7.

7. Circuit options page 61TYPE CODE DESCRIPTIONF 3XTAP822150 With side and upper outlet ports plugged

(standard): nr.2 plugsTL 3XTAP822150 With side outlet ports open: nr.1 plugTA 3XTAP822150 With upper outlet port open: nr.1 plugAE 4TAP314010 Upper power beyond port: nr. 1 plugAEK 3XTAP822150 + 4TAP314010

Closed center with side outlet port open:nr.1 plug for code type

fs: SDS100/RP--I112-- 8IM . UTUT --F--SAE*

5.

5. Complete controls page 48

6.

6.

5.

For list see page 21.





7.

SDS100

58 DBT001A

Section with optional outlet type R

DD

E

E

51

∅ 8.5

108

130

11

97 11

16

4118

69

42

95.5

6.5

AB

C

T1

“B” side option (page 41) “A” side spool positioner (page 31)

Configuration combining a working section with the closing flange to reduce dimensions.

Below it’s show a configuration with parallel circuit, port valves prearrangement, optional side and upper outlet ports plugged (F type)

VR load check valveAllen wrench 624 Nm / 17.7 lbft

Port valves (page 54)

G1/2 ports pluggedAllen wrench 824 Nm / 17.7 lbft


nr.2 G3/8 ports

∅ 0.33

1.65 2.

01

3.76

0.26

3.82 0.43

0.63

1.61

0.71

2.72

4.25 0.43

5.12

SDS100

59DBT001A

A BA B



ABD -- D

A B

Parallel circuit

Type RQ: without port valvesprearrangement

Type RP: with port valvesprearrangement

A B


RQ--101--8L--F--SAE


RP--101--8L.UTUT--

F--SAE

ABD -- D

Type RQS: without port valvesprearrangement

Type RPS: with port valvesprearrangement


RQS--101--8L--F--SAE


RPS--101--8L.UTUT--

F--SAE

Tandem circuit

It’s necessary to use QR or PR sections (see page 24).

SDS100

60 DBT001A

It’s necessary to plug port T on inlet section.

A B


RQ--101--8L--AE--SAE

E -- EC

C

A B


RQ--101--8L--AEK--SAE

E -- E


Circuit options

TL configuration

A B


RQ--101--8L--TL--SAE

E -- E

T1

T1

SA

E10

It’s necessary to plug port T on inlet section.

TA configuration

AE configuration (power beyond)

A B

Descripion example:

RQ--101--8L--TA--SAE

E -- E

T1T1

For type F standard configuration see page 59.

AEK configuration (closed center)

Outlet is on port T of inlet section. Outlet is on port T of inlet section.


M14x1,5 DIN906 plugAllen wrench 742 Nm / 31 lbft


M14x1,5 DIN906 plugAllen wrench 742 Nm / 31 lbft

SAE10

SAE10

SDS100

61DBT001A

SDS100

62 DBT001A

SDS100

63DBT001A

Contents

Dimensional data 64. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic circuit 65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ordering codes 66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


ordering codes 68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


inlet relief options 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

inlet valve options 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

E type working section

ordering codes 72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


spools 74. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

complete controls 78. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RE type working section with optional outlet

ordering codes 84. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


circuit configuration 87. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A type working section

ordering codes 88. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


RA type working section with optional outlet

ordering codes 90. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Working sections with internal pilot and drain lines

Dimensional data

Carry--over

F

E

27

8611

11

42.5 34.5 36 41

130

5442

108

NOTE -- For dimensions of sections and controls,please see the related pages.

1.06

2.12

4.25

1.65

3.39

5.13

0.43

0.43

1.67 1.36 1.42 1.61

512.01

WALVOILP0500001111020000Ref............

MADE IN ITALY

Production batch :P05 = production year (2005)00001 = progressive numberCustomer reference

Code

SDS100 sections with internal pilot and drain lines

64 DBT001A

TYPEE F Weight

TYPEE F Weight



SDS100/1 157 6.18 118 4.65 10.2 22.5 SDS100/6 337 13.27 298 11.73 28.2 62.2

SDS100/2 193 7.60 154 6.06 13.8 30.4 SDS100/7 373 14.69 334 13.15 31.8 70.1

SDS100/3 229 9.02 190 7.48 17.4 38.4 SDS100/8 409 16.10 370 14.57 35.4 78

SDS100/4 265 10.43 226 8.90 21 46.3 SDS100/9 445 17.52 406 15.98 39 86

SDS100/5 301 11.85 262 10.31 24.6 54.2 SDS100/10 481 18.94 442 17.40 42.6 93.9

Parallel

Hydraulic circuit

Tandem


SDS100/3/CR(TVG3--175)/QE--E101--8EB3/RQE--E101--8EB3--VRC--F--12VDC--SAE

A1 B1 A2 B2

P

T L V


SDS100/3/CR(TVG3--175)/QE--E101--8EB3/SQE--E101--8EB3/RQE--E101--8EB3--VRC--F--12VDC--SAE

A1 B1 A2 B2

P

T L V A1 B1

30

300µm

175502550725

435

30

300µm

175502550725

435

sections with internal pilot and drain lines SDS100

65DBT001A


66 DBT001A

zzrzzr

3b.

Codici di ordinazione

1.

SDS100/3/CRV(TVG3--175)/QE--E101--8EB3/QA--101--8L/

2a.

Ordering codes3.

nr. of workingsections

Desxription example:

1st section

1.

3a.

2b.

2b.

2a.

4.

3b.

RQA--101--8L--VRC--F

RQE--E101--8EB3--VRC--F

NOTAP(L)--12VDC--SAE*

3a.

Solenoid valvesfeeding voltage

last section

1.


67DBT001A

zzrzzr

TYPE: RQE--E101--8EB3--VRC--F--12VDCCODE: 610355005DESCRIPTION: Parallel circuit with double side electrìhydraulic controland backpressure valveTYPE: RPE--E101--8EB3.UTUT--VRC--F--12VDCCODE: 610305005DESCRIPTION: As previous with port valves prearragement

Codici di ordinazione Ordering codes

2a. Complete working section type E * page 72

1. Complete inlet section * page 68TYPE: CRV(TVG3--175)......--NOTAP(L) CODE: 610205016DESCRIPTION: Section with upper inlet, with pressure relief valve, withinternal pilot and external drain.TYPE: CRV(SV)......--NOTAP(L) CODE: 610205017DESCRIPTION: As previous with pressure relief valve blanking plug

TYPE: QE--E101--8EB3--12VDC CODE: 61055005DESCRPTION: Parallel circuit with double side electro--hydrauliccontrolTYPE: PE--E101--8EB3.UTUT--12VDC CODE: 610105007DESCRIPTION: Parallel circuit with double side electro--hydrauliccontrol and port valves prearrangementTYPE: SQE--E101--8EB3--12VDC CODE: 610125019DESCRIPTION: Tandem circuit with double side electro--hydrauliccontrolTYPE: SPE--E101--8EB3.UTUT--12VDC CODE: 610125020DESCRIPTION: Tandem circuit with double side electro--hydrauliccontrol and port valves prearrangement

4. Assembling kitCODE DIRECTIONAL VALVE5TIR110145 Tie rod kit for 1 section valve5TIR110179 Tie rod kit for 2 sections valve5TIR110215 Tie rod kit for 3 sections valve5TIR110252 Tie rod kit for 4 sections valve5TIR110289 Tie rod kit for 5 sections valve5TIR110323 Tie rod kit for 6 sections valve5TIR110359 Tie rod kit for 7 sections valve5TIR110397 Tie rod kit for 8 sections valve5TIR110431 Tie rod kit for 9 sections valve5TIR110467 Tie rod kit for 10 sections valve

3a. Section with optional outlet type E * page 84

2b. Complete working section type A * page 88TYPE: QA--101--8L CODE: 610155006DESCRIPTION: Parallel circuit with lever control and spring return inneutral positionTYPE: PA--101--8L.UTUT CODE: 610105008DESCRIPTION: Parallel circuit with lever control and spring return inneutral position, prearranged for port valvesTYPE: SQA--101--8L CODE: 610125021DESCRIPTION: Tandem circuit with lever control and spring return inneutral positionTYPE: SPA--101--8L.UTUT CODE: 610125022DESCRIPTION: Tandem circuit with lever control and spring return inneutral position, prearranged for port valves

TYPE: RQA--101--8L--VRC--F CODE: 610305006DESCRIPTION: Parallel circuit with lever control and spring return inneutral position and backpressure valveTYPE: RPA--101--8L.UTUT--VRC--F CODE: 610305007DESCRIPTION: As previous with port valves prearrangement

3b. Section with optional outlet type A * page 90

With mechanical controlsWith electrohydraulic control


Inlet and outlet section4.

4.

3.

FE SDS100 / C RV (TVG3 -- 175) ELT--12VDC ........ -- NOTAP(L) -- SAE *

1. 3. 4.

Pressure relief valve setting in bar



4. Inlet valve options page 18

3. Inlet relief options page 17

1. Section body kit * page 69

Standard setting is referred to 10 l/min flow.TYPE CODE DESCRIPTIONVMD100/1: direct pressure relief valve type T (standard)(TVG2--80) X196121081 Range 63 to 100 bar / 900 to 1450 psi



standard setting 220 bar / 3200 psi

SV XTAP526360 Pressure relief valve blanking plug

TYPE CODE DESCRIPTIONC 5FIA107705 Standard configuration fitted with relief

valve VLP

TYPE CODE DESCRIPTIONELT 5CAR407320 12 VDC solenoid operated unloader

valve5CAR407325 24 VDC solenoid operated unloader

valveSV XTAP526360 Valve blanking plug:

in valve description the word SV mustbe omitted because standard

2. Pressure reducing valve page 69TYPE CODE DESCRIPTIONRV X219740030 With pressure reducing valve VRPFSRV XTAP519350 With valve blanking plug

2.

2.

1.

5.

5.

5. Pilot and drain* page 69TYPE CODE DESCRIPTIONTAP(VL) 3XTAP817130 Internal pilot and drain: needs two

SAE6 plugsNOTAP(L) 3XTAP817130+4TAP308006 Internal pilot and external

drain: needs SAE6 plug and M8x1tapered plug

NOTAP(V) 3XTAP817130 External pilot and internal drain: needsSAE6 plug

NOTAP(VL) 4TAP308006 External pilot and drain: needsM8x1 tapered plug


68 DBT001A

54

130

11

12

12

33

4110

15

42.569

G1/2

P T

L

V

108

nr.2 ports

D

D0.47

1.301.

612.72

0.39

2.130.43

4.25

5.12

0.470.

59

1.67

T L VP

30

300µm

175502550725

435

Section kit and hydraulic circuitIt’s show a configuration with internal pilot and drain.


0

30

60

90

120

150

0 3 6 9 12 15

VLP relief valveperformance curve

Flow

Pre

ssur

e

(l/min)

(bar)

95.5

66

4

59

52

8.5∅

23.2

C -- C

C

C

85.8

0

10

20

30

40

0 100 200 300

VRP pressure reducing valveperformance curve

(internal drain)

Inlet pressure

Red

uced

pres

sure

(bar)

(bar)


CRV(TVG3--175)....-- TAP(VL)--SAE


63

Pressure reducing valve VRPFWrench 19 -- 42 Nm / 31 lbft Relief valve VLP


D -- D

Overpressure reliefvalve (pag. 17)

0.91

0.33∅

2.052.

60

3.76

0.16

2.32

3.38

2.48

1000 2000

(psi)450

300

150

3000 4000 (psi)

(psi)1500

1000

500

2000


1 2 3 (US gpm)


69DBT001A

D -- D

TL

DIN906 -- M8x1 tapered plugcode: 4TAP308006

SAE6

D

D

P T

L

V

30

300µm

175502550725

435

D -- D

TL

DIN906 -- M8x1 tapered plugcode: 4TAP308006

PT L V



Suggested configuration for valve with 8EB3LH electro--hydraulic control: required to avoid that backpressure on return can influ-

ence the hysteresis of the control.


CRV(TVG3--175)....-- NOTAP(L)--SAE

External drain configuration

External pilot and drain configuration


CRV(TVG3--175)....-- NOTAP(VL)--SAE

30

300µm

175502550725

435

PT L V

SAE6

D

D

P T

L

V


70 DBT001A

VP

T

A1 A2

B1 B2C C

V

L

C -- C

SR plugAllen wrench 642 Nm / 31 lbft



Configuration without pressure reducing valve

The electro--hydraulic control kit can be driven by connecting a pump (Q= 5 l/min -- 1.3 US gpm and Pmax= 50 bar -- 725 psi) to the

V port and replacing the pressure reducing valve with the appropriate plug (see page 69).

Available with internal or external drain.


CSRV(TVG3--175)....-- NOTAP(V)--SAE

PT L

V

175502550725


71DBT001A


72 DBT001A

Working section type E8.

1.

EL SDS100 / PE -- E101 -- 8EB3 . U100U100 -- 12VDC -- SAE *

2. 3. 8.


8.

1.

2.8.

3.

3.

1. Working sections kit * page 73Include body, seals and load check valve.TYPE CODE DESCRIPTIONQE 5EL1077012 Parallel circuit without port valves

prearrangementPE 5EL1077002 Parallel circuit with port valves

prearrangementSQE 5EL3077012 Tandem circuit without port valves

prearrangementSPE 5EL3077002 Tandem circuit with port valves

prearrangement

2. Spools page 74If not specified otherwise, the spool are from 20 to 40 l/min flowTYPE CODE DESCRIPTIONE102 3CU6710102 Double acting, 3 positions, with A and B closed

in neutral position; for flow up to 20 l/minE101 3CU6710000 As previous, from 20 to 40 l/min flowE103 3CU6710103 As previous, from 40 to 60 l/min flowE201 3CU6725000 Double acting, 3 positions, with A and B open

to tank in neutral positionE301 3CU6731000 Single acting in A, 3 positions, B plugged:

needs G3/8 plugSpecials spools for particular positioners kit pag. 77. . . . . . . . . . . . . .E501 3CU6752501 Double acting, 4 positions, floating in 4th


3. Electro--hydraulic controls page 78TYPE CODE DESCRIPTION8EB3 5IDR907312 12VDC double side proportional type with

spring return to neutral position5IDR907324 As previous 24VDC

8EB3LH 5IDR907612 12VDC double side proportional type withspring return to neutral position andwet--type lever control

5IDR907624 As previous 24VDCParticular positioners kit for special spools page 78. . . . . . . . . . . . . . .TYPE CODE DESCRIPTION13EB3 5IDR917312 AS type 8EB3, 12VDC: for spool type

E5015IDR917324 As previous 24VDC

13EB3LH 5IDR917712 AS type 8EB3LH, 12VDC: for spool typeE501

5IDR917724 As previous 24VDC

8. Port valves page 54Fixed setting antishock with prefill valves.


3.

A B

LV

A B


Working section type E

Parallel circuit

A B

A B

Tandem circuit

Type SQE: without port valvesprearrangement

Type SPE: with port valvesprearrangement

Double side electro--hydraulic control (page 78)


SPE--E101--8EB3.UTUT--12VDC--SAE


PE--E101--8EB3.UTUT--

12VDC--SAE

It can be supplied with parallel or tandem circuit; series circuit is obtained as related to page 10.

All sections are available with or without valves prearrangement

Pilot lines

L

V

LV

L

V

L

V

L

V

LV

LV

130

95.5

11 Directional controlvalve mounting face

102

51

G3/8nr.2 ports

Type QE: without port valvesprearrangement

Type PE: with portvalves prearrangement

Port valves(page 54)

2.01

0.43

5.12

3.76 4.

02


73DBT001A

stroke -- 6.5 mm-- 0.26 in

A

" stroke + 6.5 mm+ 0.26 in

0.2 0.3 0.4 0.5 0.6

Current (A)

24VDC

12VDC

0.2 0.3 0.4 0.5 0.6

0

10

20

30

40

50

0.4 0.6 0.8 1.0 1.20

10

20

30

40

50

0.4 0.6 0.8 1.0 1.2

Spools


Flo

w

(l/min )

Flo

w

Current


(A)

(l/min )

201

201

201A B

P T

A B

P T

A B

P T

FJ

Y

F

J

Y


P → A B → T

P→ B A → T

A B

T

P PLC

T

A B

T

P PLC

T

A B

T

P PLC

T

Type E101

24VDC

12VDC

F

J

Y



4

8

12

(US gpm)

4

8

12

(US gpm)


74 DBT001A

0.2 0.3 0.4 0.5 0.6

Current (A)

24VDC

12VDC

0.2 0.3 0.4 0.5 0.6

Current (A)

24VDC

12VDC

0.2 0.3 0.4 0.5 0.6

Current (A)

24VDC

12VDC

0.2 0.3 0.4 0.5 0.6

Current (A)

24VDC

12VDC

A B

T

P PLC

T

A B

T

P PLC

T

201A B

P T

201A B

P T




0

10

20

30

0.4 0.6 0.8 1.0 1.20

10

20

30

0.4 0.6 0.8 1.0 1.2

Flo

w

(l/min )

Flo

w

Spool metering A(B)→TSpool metering P→A(B)(l/min )

FJ

Y

FJ

Y

0

20

40

60

80

0.4 0.6 0.8 1.0 1.20

20

40

60

80

0.4 0.6 0.8 1.0 1.2

Flo

w

(l/min )

Flo

w

Spool metering A(B)→TSpool metering P→A(B)(l/min )

F

J

YF

J

Y

Spools

Type E102

Type E103

F

J

YP(on ports) = 63 bar / 900 psiP(on ports) = 100 bar / 1450 psiP(on ports) = 250 bar / 2900 psi


F

J

YP(on ports) = 63 bar / 900 psiP(on ports) = 100 bar / 1450 psiP(on ports) = 250 bar / 2900 psi


2

4

6

(US gpm)

2

4

6

(US gpm)

5

10

15

(US gpm)20

5

10

15

(US gpm)20

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in


75DBT001A

A B

P T

201

Spools


Type E201

Type E301

A B

P T

201


P closed, A--B to Tank, with flow through line (LC) open

A B

T

P PLC

T

G3/8 plugAllen wrench 6 -- 24 Nm / 17.7 lbft

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in

A

"

+ 6.5 mm / + 0.26 in

(0)

(1)

(2)-- 6.5 mm / -- 0.26 in


76 DBT001A

0

50

100

150

0 10 20 30 40 50

Pre

ssur

e

Flow (l/min)

(bar)


B→TA→T

(psi)

1500

1000

500

2000

Spool meteringQin = 40 l/min / P(on ports) = 100 bar / 1450 psi

0

10

20

30

40

50

0 1 2 3 4 5 6

Flo

w

Stroke (mm)

(l/min)

P→A

A→T

P→B

B→T

(in)0.1 0.2

AA

stroke -- 10.5 mm / -- 0.41 in

stroke -- 6 mm /-- 0.24 inA

"

stroke + 6 mm / + 0.24 in

QE5 -- PE5 section or RQE5 -- RPE5 optional outlet section required, contact Sales Dpt. for further information.

To be combined with 13EB3 (see page 78) or 13EB3LH (see page 82) electrohydraulic controls.

A B

T

P PLC

T

201A B

P T

3

A--B → T (floating)

Spools


Type E501

P →B A → T

P → A B → T

P--A--B--T closedflow through line (LC) open

201A B

P T

3

201A B

P T

3

201A B

P T

3

A B

T

P PLC

T

A B

T

P PLC

T

A B

T

P PLC

T


77DBT001A

“JPT” AMP connection(need connector type C08, see page 96)

8EB3 proprotional electro--hydraulic control


201

C

C

With spring return to neutral position.

Callout1) CRV type inlet cover with pressure--reducing valve (VRP), relief valve

(VLP), internal pilot and drain2) Working section (PE, QE....) with pilot lines3) Optional outlet working section (RPE, RQE) with pilot lines and backpres--

sure valve (VRC or VRE)

226

35

4823

.5

Solenoid valves operating featuresPilot max. pressure : 315 bar -- 4600 psi. . . . . . . . . . . . . . .Min. feeding pressure : 40 bar -- 580 psi. . . . . . . . . . . . .Max. backpressure on drain : 20 bar -- 290 psi. . . . . . .Max. internal leakage : 3 cm3/min -- 0.18 in3/min. . . . . . . . . . . . .Max. hysteresis : 13%. . . . . . . . . . . . . . . . . .Nominal voltage : 12 24 VDC ± 10%. . . . . . . . . . . . . . . . .Coil resistance (20°C / 68°F) : 5.3 24 Ω. . . . . . .Nominal current : 1.5 0.63 A. . . . . . . . . . . . . . . . . .Duty cycle : 100%. . . . . . . . . . . . . . . . . . . . . .Operating frequency : 125 Hz. . . . . . . . . . . . . .Weather protection : IP65. . . . . . . . . . . . . . .

0

2

4

6

8

0.0 0.4 0.8 1.2 1.6

Current -- stroke diagram

Solenoid valve current

Spo

olst

roke

(A)

(mm)

24VDC 12VDC



58

152.

5


C -- C

61

Directional valvefixing plane

P

TL

VA1 A2

B1 B2

51

(in)0.3

0.2

0.1

1.38

1.89

8.89

0.93

2.01

6.00

2.28

2.40

Solenoid valve12VDC code: 4SOL66X01224VDC code: 4SOL66X024


78 DBT001A


(VLP), internal pilot and external drain (suggested)2) Working section (PE, QE....) with pilot lines3) Optional outlet working section (RPE, RQE) with pilot lines and backpres--

sure valve (VRC or VRE)

0

2

4

6

8

0.0 0.4 0.8 1.2 1.6



Spo

olst

roke

(A)

(mm)

24VDC 12VDC

(in)0.3

0.2

0.1

Solenoid valves operating featuresPilot max. pressure : 315 bar -- 4600 psi. . . . . . . . . . . . . . .Min. feeding pressure : 40 bar -- 580 psi. . . . . . . . . . . . .Max. backpressure on drain : 20 bar -- 290 psi. . . . . . .Max. internal leakage : 3 cm3/min -- 0.18 in3/min. . . . . . . . . . . . .Max. hysteresis : 13%. . . . . . . . . . . . . . . . . .Nominal voltage : 12 24 VDC ± 10%. . . . . . . . . . . . . . . . .Coil resistance (20°C / 68°F) : 5.3 24 Ω. . . . . . .Nominal current : 1.5 0.63 A. . . . . . . . . . . . . . . . . .Duty cycle : 100%. . . . . . . . . . . . . . . . . . . . . .Operating frequency : 125 Hz. . . . . . . . . . . . . .Weather protection : IP65. . . . . . . . . . . . . . .

8EB3LH proprotional electro--hydraulic control


With spring return to neutral position and wet--type lever box.

201

C

C

296

35

47

23,5

P

TL

VA1 A2

B1 B2

4858


79DBT001A


21.Working section type E



C -- C


75.5

152.

5

51

137

5861 Special wrench

9.8 Nm / 7.2 lbft

1

2

The control is supplied with lever--holder in standard configuration; different positon must always specified (8EB3LH1 and

8EB3LH2).

Lever--holder configuration

0

Standard configuration

1

2

0

2.40

2.28

6.00

2.01

2.97

5.39




80 DBT001A

0

3

6

9

12

0.0 0.4 0.8 1.2 1.6



Spo

olst

roke

(A)

(mm) 24VDC 12VDC

13EB3 proprotional electro--hydraulic control


201

C

C

With spring return to neutral position: available for spool type E501 (see page 77).



(VLP), internal pilot and drain2) Working section (PE, QE....) with pilot lines3) Optional outlet working section (RPE, RQE) with pilot lines and backpres--

sure valve VRC(21)

226

35

4823

.5

Operating featuresSOLENOID VALVESPilot max. pressure : 315 bar -- 4600 psi. . . . . . . . . . . . . . .Min. feeding pressure : 40 bar -- 580 psi. . . . . . . . . . . . .Max. backpressure on drain : 20 bar -- 290 psi. . . . . . .Max. internal leakage : 3 cm3/min -- 0.18 in3/min. . . . . . . . . . . . .Max. hysteresis : 13%. . . . . . . . . . . . . . . . . .Nominal voltage : 12 24 VDC ± 10%. . . . . . . . . . . . . . . . .Coil resistance (20 °C) : 5.3 24 Ω. . . . . . . . . . . .Nominal current : 1.5 0.63 A. . . . . . . . . . . . . . . . . .Duty cycle : 100%. . . . . . . . . . . . . . . . . . . . . .Operating frequency : 125 Hz. . . . . . . . . . . . . .Weather protection : IP65. . . . . . . . . . . . . . .



58

150.

7


C -- C

61



P

TL

VA1 A2

B1 B2

51

1.38

1.89

8.89

0.93

2.01

5.93

2.28

2.40

(in)

0.3

0.2

0.1

0.4

Notch 1.7 mm0.067 in9.8 Nm / 7.2 lbf


81DBT001A

C

C

296

35

47

23.5

P

TL

VA1 A2

B1 B2

4858

0.93

1.89

11.6

5

1.85

2.28

0

3

6

9

12

0.0 0.4 0.8 1.2 1.6



Spo

olst

roke

(A)

(mm) 24VDC 12VDC(in)

0.3

0.2

0.1

0.4

Operating featuresSOLENOID VALVEPilot max. pressure : 315 bar -- 4600 psi. . . . . . . . . . . . . . .Min. feeding pressure : 40 bar -- 580 psi. . . . . . . . . . . . .Max. backpressure on drain : 20 bar -- 290 psi. . . . . . .Max. internal leakage : 3 cm3/min -- 0.18 in3/min. . . . . . . . . . . . .Max. hysteresis : 13%. . . . . . . . . . . . . . . . . .Nominal voltage : 12 24 VDC ± 10%. . . . . . . . . . . . . . . . .Coil resistance (20 °C) : 5.3 24 Ω. . . . . . . . . . . .Nominal current : 1.5 0.63 A. . . . . . . . . . . . . . . . . .Duty cycle : 100%. . . . . . . . . . . . . . . . . . . . . .Operating frequency : 125 Hz. . . . . . . . . . . . . .Weather protection : IP65. . . . . . . . . . . . . . .


(VLP), internal pilot and external drain (suggested)2) Working section (PE, QE....) with pilot lines3) Optional outlet working section (RPE, RQE) with pilot lines and backpres--

sure valve VRC(21)



With spring return to neutral position and wet--type lever box: available for spool type E501 (see page 77).

201


82 DBT001A


21.Working section type E


C -- C


75.5

150.

7

51

137

5861 Special wrench

9.8 Nm / 7.2 lbft

1

2

The control is supplied with lever--holder in standard configuration; different positon must always specified (13EB3LH1 and

13EB3LH2).

Lever--holder configuration

0

Standard configuration

1

2

0

2.40

2.28

5.93

2.01

2.97

5.39




Notch 1.7 mm / 0.067 in9.8 Nm / 7.2 lbf


83DBT001A


84 DBT001A

Side port plugged:non modifiable

Section with optional outlet type RE13.

1.

EL SDS100 / RPE -- E101 -- 8EB3 . U100U100 -- VRC -- F -- 12VDC *

2. 3. 4.

Valve description:

4.

1.

2.4.

3.

3.

1. Working section kit * page 85Include body, seals and load check valve.TYPE CODE DESCRIPTIONRQE 5FIA207712 Parallel circuit without port valves

prearrangementRPE 5FIA207702 Parallel circuit with port valves

prearrangement

2. Spools page 74If not specified otherwise, the spool are from 20 to 40 l/min flowTYPE CODE DESCRIPTIONE102 3CU6710102 Double acting, 3 positions, with A and B closed

in neutral position; for flow up to 20 l/minE101 3CU6710000 As previous, from 20 to 40 l/min flowE103 3CU6710103 As previous, from 40 to 60 l/min flowE201 3CU6725000 Double acting, 3 positions, with A and B open

to tank in neutral positionE301 3CU6731000 Single acting in A, 3 positions, B plugged:

needs G3/8 plugSpecials spools for particular positioners kit pag. 77. . . . . . . . . . . . . .E501 3CU6752501 Double acting, 4 positions, floating in 4th


3. Electro--hydraulic controls page 78TTYPE CODE DESCRIPTION8EB3 5IDR907312 12VDC double side proportional type with

spring return to neutral position5IDR907324 As previous 24VDC

8EB3LH 5IDR907612 12VDC double side proportional type withspring return to neutral position and

wet--type lever control5IDR907624 As previous 24VDC

Particular positioners kit for special spools page 78. . . . . . . . . . . . . . .TYPE CODE DESCRIPTION13EB3 5IDR917312 AS type 8EB3, 12VDC: for spool type

E5015IDR917324 As previous 24VDC

13EB3LH 5IDR917712 AS type 8EB3LH, 12VDC: for spool typeE501

5IDR917724 As previous 24VDC

4. Port valves page 54Fixed setting antishock with prefill valves.


5.

5.

5. Circuit options * page 87TYPE CODE DESCRIPTIONVRC 5GIU511380 Backpressure valve for 8EB3 and

8EB3LH controlsVRC(21) 5GIU511381 Backpressure valve for 13EB3 and

13EB3LH controlsVRE 5GIU532610 Backpressure valve and carry--over:

include M14x1.5 plug. Only for 8EB3 and8EB3LH controls

3.

Section with optional outlet type RE

DD

E

E

51

∅ 8.5

108

130

11

97 11

16

4118

69

42

95.5

AB

T1

Configuration combining a working section with the closing flange to reduce dimensions.

Below it’s show a configuration with parallel circuit, baclpressure valve, optional side outlet port plugged (F type).


nr.2 SAE8 ports

VR load check valveAllen wrench 6 -- 24 Nm / 17.7 lbft

Double side electro--hy-draulic control (page 78)

∅ 0.33

1.65 2.

01

3.76

3.82 0.43

4.25 0.43

5.12

0.63

0.71

1.61 2.

72


85DBT001A



A B

Type RQE: without port valvesprearrangement

Type RPE: with port valvesprearrangement


A B


RQE--E101--8EB3--VRC--F--12VDC--SAE

D -- D


RPE--E101--8EB3.UTUT--VRC--F--12VDC--SAE

A B

Pilot lines

L

V

L

V

LV

LV

LV

LV


86 DBT001A

600

400

200

800

0

20

40

60

0 20 40 60

VRC(21) performace diagram

Flow

Pre

ssur

e

(l/min)

(bar)(psi)

0

20

40

60

0 20 40 60

VRC performace diagram

Flow

Pre

ssur

e

(l/min)

(bar)(psi)

600

400

200

800

Performace diagram

0

10

20

30

40

0 20 40 60Flow

Pre

ssur

e

(l/min)

(bar) (psi)

480

320

160

(US gpm)5 10 15

Circuit options


E -- E

With VRC backpressure valve

A B


RQE--E101--8EB3--VRC

--F--12VDC--SAE

With VRE backpressure valve (power beyond)

E -- E

A B


RQE--E101--8EB3--VRE--F--12VDC--SAE

102

131

C

C

4.02

5.16

M14x1.5 DIN906 plugAllen wrench 7 -- 42 Nm / 31 lbft

SAE10 VRE valveWrench 32 -- 24 Nm /17.7 lbft

VRC valve plugWrench 27 -- 24 Nm / 17.7 lbft

VRC valve

5 10 15 (US gpm)

5 10 15 (US gpm)


87DBT001A


88 DBT001A

Working section type A17.

EL SDS100 / PA -- 101 -- 8 L . U100 U100 *

1a.


EL SDS100 / QA -- I112 -- 8IM

EL SDS100 / QA -- S112 -- 8ES3 -- 12VDC

1a.

1b.

1b.

1a. Working section kit * page 89For mechanical controls.Include body, seals, rings and load check valve.TYPE CODE DESCRIPTIONQA 5EL1077013 Parallel circuit without port valves

prearrangementPA 5EL1077003 Parallel circuit with port valves

prearrangementSQA 5EL3077013 Tandem circuit without port valves

prearrangementSPA 5EL3077003 Tandem circuit with port valves

prearrangement

1b. Working section kit *For proportional hydraulic and ON/OFF solenoid controls.Include body, seals and load check valve.TYPE CODE DESCRIPTIONQA/IM--ES 5EL1077013A Parallel circuit without port valves

prearrangementPA/IM--ES 5EL1077003A Parallel circuit with port valves

prearrangementSQA/IM--ES 5EL3077013A Tandem circuit without port valves

prearrangementSPA/IM--ES 5EL3077003A Tandem circuit with port valves

prearrangement


I

I

I

I Other options page 21For complete list of spools, controls and port valves see page 21:available options are the same of directional valve with standardworking scetion.

A B


Working section type A

Sections with pilot lines for manual/mechanical control in electro--hydraulic valves.

Dimensions are the same as other sections.

A B


PA--101--8L.UTUT--SAE

Type QA: without port valvesprearrangement

Type PA: with port valvesprearrangement

Port valves(pag. 54)

”A” side spool positioner (page 31) “B” side options (page 41)

Parallel circuit

Tandem circuit

Pilot through and drain

A B


SPA--101--8L.UTUT--SAE

A B

Type SQA: without port valvesprearrangement

Type SPA: with port valvesprearrangement



89DBT001A


90 DBT001A

Side port plugged:non modifiable

Section with optional outlet type RA19.

1a.

EL SDS100 / RPA -- 101 -- 8L . U100U100 -- VRC -- F *


1a.

1a. Working section kit * page 91For mechanical controls.Include body, seals, rings and load check valve.TYPE CODE DESCRIPTIONRQA 5FIA207714 Parallel circuit without port valves

prearrangementRPA 5FIA207706 Parallel circuit with port valves

prearrangement


2.

2. Circuit options * page 87TYPE CODE DESCRIPTIONVRC 5GIU511380 Backpressure valve for 8EB3 and

8EB3LH controlsVRC(21) Backpressure valve for 13EB3 and

13EB3LH controlsVRE 5GIU532610 Backpressure valve and carry--over:

include M14x1.5 plug. Only for 8EB3 and8EB3LH controls

2.

1b. Working section kit *For proportional hydraulic and ON/OFF solenoid controls.Include body, seals and load check valve.TYPE CODE DESCRIPTIONRQA/IM--ES 5FIA207716A Parallel circuit without port valves

prearrangementRPA/IM--ES 5FIA207706A Parallel circuit with port valves

prearrangementEL SDS100 / RQA -- I112 -- 8IM -- VRC -- F *

EL SDS100 / RQA -- S112 -- 8ES3 -- VRC -- F -- 12VDC *

1b. 2.

2.1b.

I

I

I

I Other options page 21For complete list of spools, controls and port valves see page 21:available options are the same of directional valve with standardworking scetion.

I


Section with optional outlet type RA

A B

Type RQA: without port valvesprearrangement

Type RPA: with port valvesprearrangement


A B

Descriprion example:

RQA--101--8L--VRC

--F--SAE

D -- D


RPA--101--8L.UTUT--VRC

--F--SAE

A B

L

V

L

V

For dimensions and characteristics see section type RE at page 85.

”A” side spool positioner (page 31) “B” side options (page 41)


A B


RQA--101--8L--VRE

--F--SAE

C


RPA--101--8L.UTUT--VRE

--F--SAE

A B

Type RQA: without port valves prearrangement Type RPA: with port valves prearrangement


91DBT001A

SDS100

92 DBT001A

SDS100

93DBT001A

Fitting tightening torque -- Nm / lbft

THREADS TYPE P and C ports A and B ports T port V and L ports

BSP (ISO 228/1) G 1/2 G 3/8 G 1/2 G 1/4

With O--Ring seal 50 / 36.9 35 / 25.8 50 / 36.9 20 / 14.7

With copper washer 60 / 44.3 40 / 29.5 60 / 44.3 25 / 18.4

With steel and rubber washer 60 / 44.3 30 / 22.1 60 / 44.3 16 / 11.8

UN--UNF (ISO 11926--1) 7/8--14 (SAE 10) 3/4--16 (SAE 8) 7/8--14 (SAE 10) 9/16--18 (SAE 6)

With O--Ring seal 90 / 66.4 35 / 25.8 90 / 66.4 30 / 22.1

6.Installation and maintenance

A2

P

A1

B1B2

The SDS100 valve is assembled and tested as per the technical specification of this catalogue.

Before the final installation on your equipment, follow the below recommendations:

-- the valve can be assembled in any position, in order to prevent body deformation and spool sticking mount the product on a flat

surface;

-- in order to prevent the possibility of water entering the lever box and spool control kit, do not use high pressure wash down directly

on the valve;

-- prior to painting, ensure plastic port plugs are tightly in place.

NOTE -- These torque are recommended. Assembly tightening torque depends on many factors, including lubrication, coating andsurface finish. The manufacturer shall be consulted.

T

P

V

L T

P

A2A1

B1B2

SDS100/2/CN(TVG3--175)/Q--101--8L/RQ--101--8L--F SDS100/2/CRV(TVG3--175)/

QE--E101--8EB3/RQE--E101--8EB3LH--VRC--F--12VDC

Installation and maintenance7.

NOTE -- All moving parts inside cap, lever box and mechanical joystick arelubricated with synthetic base grease grade NLGI2

1) Inlet cover2) Overpressure relief valve3) Overpressure relief valve blanking plug4) Working section5) Spool: normally spools are interchangeable,

verify the smoothness during the assembly6) “A” side spool positioner7) Lever pivot box8) Dust--proof flange9) Port valves10) Load check valve11) Working section with optional outlet12) Holding O--Ring washer code: 3ANE12602013) O--Ring seal 14.00x2 code: 4GUA114020

Callout

Sealing edge

Washer chamfer

Mechanical control configuration.

SDS100

94 DBT001A

Malfunction Cause Remedy

External leakage pivot box lever orcontrol kit side.

Worn spool seal due to mechanicalactuation. Locate the leakage and replace the seal.

Excessive internal leakage on A and Bports.

Increase clearance between spools andbody due to high wear.

Replace the working section and checkthe oil contamination level.

Dropping load during transition whileraising. High leakage on the load check valve. Remove the load check valve and clean

the seat, verifing it’s not dented.

Inability to build pressure on A and B Pressure relief valve blocked open. Remove and clean or replace the valve.Inability to build pressure on A and Bports. Low pump pressure and flow. Check the pump and circuit.

Installation and maintenance

1) Inlet cover.2) Overpressure relief valve.3) Overpressure relief valve blanking plug.4) Main pressure reducing valve.5) Working section type E.6) Spool: normally spools are interchangeable,

verify the smoothness during the assembly.7) 8EB3 spool control.8) 8EB3LH spool control.9) Pressure reducing valves.10) Port valve.11) Load check valve.12) Working section with optional outlet type RE, with

backpressure valve.

Callout

Electrohydraulic proportional control configuration.

SDS100

95DBT001A

Malfunction Cause Remedy

External leakage pivot box lever orcontrol kit side.

Worn spool seal due to mechanicalactuation or high back pressure. Sostituire le guarnizioni usurate.

Excessive internal leakage on A and Bports.

Increase clearance between spools andbody due to high wear.

Replace the working section and checkthe oil contamination level.

Dropping load during transition whileraising. High leakage on the load check valve. Remove the load check valve and clean

the seat, verifing it’s not dented.Pressure relief valve blocked open. Remove and clean or replace the valve.

Inability to build pressure on A and BLow pump pressure and flow. Check the pump and circuit.

Inability to build pressure on A and Bports. Current absence to pressure reducing

solenoid valves Check the electric circuit.

Low pilot circuit pressure. Check the pilot circuit.

32

17.3

2P male case with female endtype AMP “Superseal”

Type C24 code: 5CON0031

1.26

0.68

Accessories8.

Connectors

3P+T according toISO4400 / EN175301--803

42.5

28.5

14

28

1

PG09

Type C03 codice: 2X1001030

0

47

2P female case with male endtype PACKARD “Weather Pack”


24

1.85

0.94

27.5

23

2P male case with female endtype PACKARD “Metri--Pack”


1.08

0.91

22.9

15.2

2P female case with male endtype AMP “Fastin--Faston”


100.39

0.90

0.60

28.4

15

2P male case with female endtype Deutsch DT06--2S


1.12

0.59

2P female case with female endtype AMP “Junior--Power--Timer”


37.5

11.817

16 0.63

0.67 0.46

1.48

40.5

21.3

2P male case with female endtype PACKARD “Weather Pack”


1.59

0.84

23.5

40.531

.5

31.5

2P+T according to EN175301--803

Type C01 code: 2X1001020

PG09

1.24

1.591.

24

0.93

50

33

2P+T according toISO4400 / EN175301--803

12

PG09

30

Type C02 code: 2X1001010

1.30

1.97

1.18 1.12

0.55

1.67

1.10

SDS100

96 DBT001A

SDS100

97DBT001A

Type Poles Nominal voltage Nominalcurrent

Permitted conductorsection range

Permitted cablediameter range

Weatherprotection

C01 2P + T 250 VAC / 300 VDC 10 A max.1.5 mm2 / max.0.0023 in2 6--8 mm / 0.24--0.31 in IP65

C02 2P + T 250 VAC / 300 VDC 10 A max.1.5 mm2 / max.0.0023 in2 6--8 mm / 0.24--0.31 in IP65

C03 3P + T 250 VAC / 300 VDC 10 A max.1.5 mm2 / max.0.0023 in2 6 to 8 mm / 0.24 to 0.31 in IP65

C07 2P / 20 A 1--2 mm2 / 0.00155--0.0031 in2 2.8--3.5 mm / 0.11--0.14 in IP67

C08 2P 250 VAC 12 A 0.5--1 mm2 / 0.00077--0.00155 in2 1.3--1.7 mm / 0.051--0.063in IP65

C17 2P / 20 A 1--2 mm2 / 0.00155--0.0031 in2 1.4--1.6 mm / 0.055--0.067in IP67

C19 2P / 13 A 1--1.2 mm2 / 0.00155--0.00186 in2 2.2--3.5 mm / 0.088--0.14 in IP67

C20 2P / 14 A 0.8--1 mm2 / 0.00124--0.00155 in2 1.3--1.7 mm / 0.051--0.067in /

C21 2P / 7A 0.3--0.8 mm2 / 0.00046--0.00124 in2 2.2--3 mm / 0.087--0.118 in /

C24 2P / 14A 0.3--0.5 mm2 / 0.00046--0.00077 in2 1.4--1.7 mm / 0.055--0.067 in IP67

Accessories

Connectors

SDS100

98 DBT001A

SDS100

99DBT001A

WALVOIL S.P.A.

42100 REGGIO EMILIA • ITALY • VIA ADIGE, 13/DTEL. +39.0522.932411 • FAX +39.0522.300984

E--MAIL: [email protected] • HTTP: //WWW.WALVOIL.COM

SALES DEPARTMENT

TEL. +39.0522.932555 • FAX +39.0522.932455

D1409808IDBT001A

SECTIONAL DIRECTIONAL CONTROL VALVES · SDS100 2 DBT001A Simple, compact and heavy duty designed...

Documents

Transcript of SECTIONAL DIRECTIONAL CONTROL VALVES · SDS100 2 DBT001A Simple, compact and heavy duty designed...