Last Updated July 2007

C. ARCHITECTURAL REQUIREMENTS – TABLE OF CONTENTS UNSW DESIGN & CONSTRUCTION REQUIREMENTS – WEB ENTRY PAGE SECTION A – INTRODUCTION SECTION B – DEVELOPMENT & PLANNING C. ARCHITECTURAL REQUIREMENTS – SCHD. OF CHANGES – REV 4.1 ..............3 C ARCHITECURAL REQUIREMENTS.............................................................................4

C.1 GENERAL...........................................................................................................4 C.1.1 Structural Requirements...................................................................................4 C.1.2 Durability of Building Fabric..............................................................................4 C.1.3 Concrete Mix. UNSW80 Specification.............................................................4

C.2 EXTERNAL FABRIC...........................................................................................4 C.2.1 Walls.................................................................................................................4 C.2.2 Windows...........................................................................................................4 C.2.3 External Doors..................................................................................................5 C.2.4 Roofs ................................................................................................................5

C.3 INTERNAL WALLS PARTITIONS & FINISHES .................................................6 C.3.1 Room Security..................................................................................................6 C.3.2 Partitions\ .........................................................................................................7 C.3.3 Internal Finishes...............................................................................................8 C.3.4 Walls.................................................................................................................8 C.3.5 Floors ...............................................................................................................8

C.4 DOORS AND DOOR FURNITURE ....................................................................8 C.4.1 New and Existing Buildings ..............................................................................8 C.4.2 General.............................................................................................................8 C.4.3 Door Types:......................................................................................................9

C.5 EXISTING BUILDINGS (Schlage Version) .........................................................9 C.5.1 Type 1 - Single Leaf Fire Doors .......................................................................9 C.5.2 Type 2 - Double Leaf Fire Doors ....................................................................11 C.5.3 Type 3 - Single Leaf Solid Core .....................................................................13 C.5.4 Type 4 - Double Leaf Solid Core ....................................................................15 C.5.5 Type 5 - Auto Sliding Doors Frameless and Aluminium.................................15 C.5.6 Type 6 - Double Leaf Aluminium Doors (1 Leaf fixed with mid rail) ..............16 C.5.7 Type 7 - Single Leaf Aluminium Doors (with Mid Rail) ...................................17

C.6 NEW BUILDINGS (Lockwood Version) ............................................................18 C.6.1 Type 1 - Single Leaf Fire Doors .....................................................................18 C.6.2 Type 2 - Double Leaf Fire Doors ....................................................................21 C.6.3 Type 3 - Single Leaf Solid Core .....................................................................22 C.6.4 Type 4 - Double Leaf Solid Core ....................................................................25 C.6.5 Type 5 - Auto Sliding Doors Frameless and Aluminium.................................25 C.6.6 Type 6 - Double Leaf Aluminium Doors (1 Leaf fixed with mid rail) ..............26

C.7 SIGNAGE .........................................................................................................27 C.7.1 Background ....................................................................................................27 C.7.2 General...........................................................................................................27

UNSW

1/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

SECTION D – EXTERNAL WORKS SECTION E.1 – HYDRAULIC SERVICES SECTION E.2 – MECHANICAL SERVICES SECTION E.3.1 – ELECTRICAL SERVICES SECTION E.3.2 – LIGHTING SECTION E.3.3 – SPECIAL SYSTEMS SECTION E.3.4 – HIGH VOLTAGE SECTION E.4 – COMMUNICATIONS SECTION E.5 – LIFTS SECTION E.6 – FUME CUPBOARDS SECTION F – SPECIFIC AREA REQUIREMENTS APPENDIX 1 – BUILDING AUTOMATION AND CONTROL SYSTEMS SPECIFICATION APPENDIX 2 – CONCRETE FOR STRUCTURES APPENDIX 3 – UNSW CONTROL SYSTEM STANDARDS HVAC APPENDIX 4 – DOCUMENT REQUIREMENTS APPENDIX 5 – UNSW STANDARD PRELIMINARIES APPENDIX 6 – SECURITY SYSTEMS

UNSW

2/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

C. ARCHITECTURAL REQUIREMENTS – SCHD. OF CHANGES – REV 4.1 As a guide only, attention is drawn to changes that have been made in the following clauses since the last revision Clause Date General revision November 2003 No change August 2004 C.4 Revised and added February 2007

UNSW

3/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

C ARCHITECURAL REQUIREMENTS

C.1 GENERAL

C.1.1 Structural Requirements All structural engineering design is to be in accordance the Earthquake Code.

C.1.2 Durability of Building Fabric UNSW Kensington Campus is located approximately 3 kilometres from the coast. External building materials and structural components are to be resistant to the corrosive salt laden environment and are to be selected to ensure building durability.

C.1.3 Concrete Mix. UNSW80 Specification See Appendix 2

C.2 EXTERNAL FABRIC

C.2.1 Walls Walls are to be durable with material selection and detailing fit for purpose. a) Base and plinth sections of walls are to resist physical wear from day to day

activity such as hand trolley and skateboards collisions, and impacts and scuffing from maintenance equipment such as cleaning machines and mowers. Mitre joints in terrazzo and stone cladding and painted render plinths are not acceptable.

b) Upper section of walls are to be low maintenance and resistant to degradation by

weathering. Sealants are not to be the primary weather barrier.

C.2.2 Windows All window framing is to be of commercial quality aluminium extrusion. The choice of extrusion should be based on future availability to allow later matching of profile for modification and replacement. Aluminium framing is to have a high quality corrosion resistant powdercoat or anodised finish. Powder coating is to be Dulux ‘best quality’ warranty grade polyester. Anodising is to be minimum thickness 20 microns. Windows are to be constructed and installed to minimum Terrain Category 2.5. Windows to be designed and installed with mechanical means as the primary form of weatherproofing.

UNSW

4/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Vacuum-sealed double glazed sashes incorporating venetian blinds are not to be used.

C.2.2.1 Function Windows sashes that can be cleaned from the inside are preferred. Sealants must be selected to be appropriate for their application and must be colour matched to the finished surface. Sealants are not to be used as the primary waterproofing barrier.

C.2.2.2 Cleaning Windows should be easily accessible for cleaning. Fixed sun screening is to be offset from the windows to allow window cleaning.

C.2.3 External Doors Refer also: DOORS & DOOR FURNITURE

The number and position of external doors is to be carefully considered and limited to avoid an unnecessary number of access points. South facing doors should be adequately weather protected.

C.2.4 Roofs Pitched roofs must be provided to all buildings as far as practicable. Minimum pitch must be not less than manufacturer's recommendations and an appropriate safety margin provided to suit prevailing conditions. Roof design should discourage pigeon nesting.

C.2.4.1 Roof Types

C.2.4.1.1 Steel Sheet Roofing.

Profiled ‘zincalume’ or ‘colorbond’ sheet steel roofing is acceptable for general use where there are a minimum number of roof penetrations. Sheet steel roofing is to be minimum 0.47 mm thickness. ‘Colorbond’ finish is to be XSO grade.

C.2.4.1.2 Aluminium Sheet Roofing.

Profiled aluminium sheet roofing is to be used for roofs where there are a large number of penetrations. Associated flashings for penetrations are to be of welded construction.

C.2.4.1.3 Membrane Roofing.

UNSW

5/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

The use of roofing membranes is to be minimised. Membrane roofing is to be “Wolfin” PVC membrane.

C.2.4.2 Roof Flashings, Trays & Penetrations

C.2.4.2.1 Sheet metal roof accessories.

Accessories are to match roofing in both appearance and galvanic characteristics. Assemblies should not rely on sealants. Fully welded assemblies are the preferred method.

C.2.4.2.2 Roof Gutters.

Gutters are to be of fail-safe design with external overflows. Box gutters are to be avoided. All gutters must be easily accessible. Downpipes. All downpipes to be external to the building.

C.2.4.3 Roof Access

C.2.4.3.1 Roof Access Hatches

Provide roof access from a service area or room such as a plantroom by a personnel door, or by means of a sliding aluminium and stainless steel hatch. A permanent steel ladder is to be provided where access to roofs is required, preferably located in a plantroom or a separately enclosed space. A hot dipped galvanised roof ladder must also be provided at changes in roof levels.

C.2.4.3.2 Roof Walkways

Roof walkways of approved construction must be provided to access any roof mounted plant.

C.2.4.3.3 Roof Spaces

All roof spaces must have permanent, fixed, adequate access. They must be provided with catwalks and be sufficiently lit to enable the roof space to be traversed without danger 24 hours a day.

C.2.4.4 Roof Safety See ‘Work Cover - Code of Practice’. “Safe Work on Roofs – Part 1”.

C.3 INTERNAL WALLS PARTITIONS & FINISHES

C.3.1 Room Security Security for internal doors is to be to a level appropriate to exposure. Two broad scenarios exist, doors securing rooms/open plan spaces off corridors, and offices within these secured zones. Incorporate all measures depending on location type. UNSW

6/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

1 – Perimeter Secure Zone - Secure Door Between Office & Coridor With Sidelights

• Extended throw latch. • Heavy duty 100X50 aluminium section jamb • Snap in jamb rebate with large fin. • Door tolerance max. 3mm all round. • Side lights to have mid-rail lined in line with door lock. • Flush mounted striker. • Obscure film to side-lights

1a – Perimeter Secure Zone - Secure Door Between Office & Coridor Without Sidelights

• Extended throw latch • Slim Line aluminium section jamb. • Snap in jamb rebate with larger fin. • Door tolerance max. 3mm all round. • Flush mounted striker.

2 –Within Secured Zone - Door Between Office & Secured Area With Sidelights

• Standard throw latch. • Snap in jamb rebate with larger fin. • Slim Line aluminium section jamb security fixed to backing column. • Door tolerance max. 3mm all round. • Flush mounted striker. • Clear glazing side-lights

2a – Within Secure Zone - Door Between Office & Secured Area Without Sidelights

• Standard throw latch. • Snap in jamb rebate with large fin. • Slim Line aluminium section jamb security fixed to backing studs. • Door tolerance max. 3mm all round. • Flush mounted striker.

C.3.2 Partitions\ Stud / plasterboard partitioning to be used in preference to proprietary / modular systems. Partitions to be steel stud frame construction. Partition systems to be of robust construction, provide a level of security appropriate to location and be capable of accepting doors and door furniture to UNSW requirements.

UNSW

7/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

C.3.3 Internal Finishes

C.3.4 Walls. Paint finishes in high use areas such as foyers and corridors to be minimum semi-gloss acylic.

C.3.5 Floors Floor finishes are to be durable and appropriate to use and location. Floor finishes in high traffic areas to be dirt resistant. Non-slip surfaces are to be provided to areas that are likely to be subjected to water. For example foyers and laboratories. See also: Section B

C.3.5.1 Carpet. Preferred carpet. 80 wool/ 20 synthetic.

C.3.5.2 Sheet Flooring “Tarket” sheet vinyl or “Flowtex” vinyl carpet.

C.3.5.3 Applied Floor Finishes. Applied two pack epoxy to specialist areas.

C.4 DOORS AND DOOR FURNITURE

C.4.1 New and Existing Buildings Hardware and Lock selection for any NEW stand alone building to be a mortice lock system based on LOCKWOOD 3570 range in conjunction with LOCKWOOD 1800/70 series furniture. See Lockwood below. Hardware and Lock selection for refurbishments, alterations and additions to existing buildings is to match existing, being SCHLAGE “Vandlgard” series. See Schlage below.

C.4.2 General a) No locks to be mounted on the bottom or top rail of doors, for OH&S reasons. b) Cardax doors, refer: Appendix 6 c) Where Schlage series locking is used, all Cardax doors are to use ES2000

electric strike\s to have storeroom function locksets regardless of door type. d) Where Lockwood series locking is used, all Cardax doors are to use appropriate

Lockwood electronic mortice lock. e) Sliding doors should be used for all main automatic exit/entry doors f) All hinges are to be Satin Stainless Steel, unless aluminium hinges are

scheduled for aluminium doors g) A minimum of 3 hinges are to be used on all standard doors h) Drop plates for the LCN 1461 door closer are to used on aluminium doors when

required

UNSW

8/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

i) All hardware is to be of heavy duty construction j) Any variations or changes to hardware are to be in writing and addressed to

UNSW Locksmith and project managers for approval k) All doors requiring patch fittings are to be approved by UNSW Locksmith and

project managers l) Include Lockwood SS092 security strike shied to all outward opening doors in

secure situations.

C.4.3 Door Types: DOOR TYPES

Type 1 Single Leaf Fire Door/Solid Core Door Type 2 Double Leaf Fire Door/Solid Core Door Type 3 Single Leaf Solid Core Type 4 Double Leaf Solid Core (to be specified) Type 5 Auto Sliding Door Frameless and Aluminium Type 6 Double Leaf. Aluminium Door (1 Leaf Fixed) Type 7 Single Leaf Aluminium Door

C.5 EXISTING BUILDINGS (Schlage Version)

C.5.1 Type 1 - Single Leaf Fire Doors 45mm to 50mm "E" core Signage: refer to BCA Clause D2.23 Keying by UNSW Locksmiths

C.5.1.1 Type 1 - Fire Door & Frame Design: Doors must be constructed with; Solid steel (NON PERFERATED) metal plates to include; Hinge plates. Lock boxes. Door closer plates. These are to provide adequate fixings & strength for maintenance purposes. Frames must have: Screw fixes hinges into jambs. To be drilled & tapped. No welded hinges or weld in hinges are to be used.

C.5.1.2 Type 1 - Hardware & Lock Selection

C.5.1.2.1 Type 1A - Plantrooms

Lock/Latches Schlage: ND96PD Vandlgard )Storeroom)

Rhodes 70mm backset, scp Door Closer LCN: Super stock 1461 scp Electric Strikes Padde: ES2000 (with micro/s tongue sensor)

UNSW

9/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Swipe Card Cardax Card reader Door Stop Boyd: DS110 scp Hinges x 3 Satin stainless steel fixed pin hinges

NOTE: If Cardax access is required see Section B

C.5.1.2.2 Type 1B - Switchboards Cupboards

Lock/Latches Schlage: ND96PD Vandlgard (storeroom)

Rhodes 70mm backset, scp (Optional) Boyd 391 with EFCO 507 R.N.L. scp Door Closer LCN: Super stock 1461 scp Hinges x 3 Satin stainless steel fixed pin hinges

C.5.1.2.3 Type 1C - Stairwells (Option 1 Non-Secure)

Lock/Latches Lockwood: 8530 – 425sc – Double action

latch with a Padde N.E. latch (part no. FCH00103) in head of frame

Door Closer LCN: Super stock 1461 scp Push/Pull Plates Boyd: 1515 sss push plate V/F engraved

“PUSH” – black Boyd: 1509 sss pull handle C/F engraved “PULL” black

Door Stop Boyd: DS 110 scp Hinges Satin stainless steel fixed pin hinges

C.5.1.2.4 Type 1C - Stairwell (Option 2 Secure)

Lock/Latches Schlage: ND94PD Vandlgard (classroom)

Rhodes 70mm backset, scp Door Closers LCN: 4314 ME Sentronic (>900mm leaf) H/Open 24V Connected LCN: 4313 ME Sentronic (<900mm leaf) (Optional) to (Stand alone unit – door release button) Reed Switch Mimic Panel Sentrol: 1078 Reed switch Door Closer LCN: Super stock 1461 scp Door Stop Boyd: DS 110 scp Hinges Satin stainless steel fixed pin hinges

C.5.1.2.5 Type 1D - Office (if required)

UNSW

10/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Lock/Latches Schlage: ND92PD Vandlgard (entrance)

Rhodes 70mm backset, scp Door Closer LCN: Super stock 1461 scp Door Stop Boyd: DS 110 scp View Panel (if required) As per AS 1905.1 – 1990 Hinges Satin stainless steel fixed pin hinges

C.5.1.2.6 Type 1 - Duct Access Panel (“E Core” Fire Door Panel)

Lock/Latches Boyd: 391 cylinder with EFCO 507 R.N.L. scp Door Closer LCN: Super stock 1461 scp Hinges Satin stainless steel fixed pin hinges

C.5.1.2.7 Type 1 - Duct “Trafalgar” Duct Access Panel

Lock/Latches Boyd: 391 cylinder with EFCO 507 R.N.L. scp Hinges Satin stainless steel fixed pin hinges

Note: All other furniture to be supplied by Trafalgar Pty Ltd

C.5.2 Type 2 - Double Leaf Fire Doors 45mm to 50mm – “E” core Signage: Refer BCA Clause D2.23 Keying by UNSW Locksmiths

C.5.2.1 Type 2 - Hardware & Lock Selection

C.5.2.1.1 Type 2A - Plantrooms “T” Section Meeting Stiles

Lock/Latches Schlage: ND96PD Vandlgard (storeroom)

Rhodes 70mm backset, scp on (active leaf) with, Sabre: 940 scp auto flush bolts (inactive leaf)

Electric Strike Padde: ES 2000 (with micro/s tongue sensor) Door Closer LCN: Super stock 1461 scp Swipe Card Cardax : Card reader Door Stop Boyd: DS 110 scp Sequence Closer Glynn Johnson: Cor 2 x FB series Hinges Satin stainless steel fixed pin hinges

Note: If Cardax access is required, see Section B

UNSW

11/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

C.5.2.1.2 Type 2B - Fire Isolated Passages Bullnose Meeting Stiles (Non Secure)

Lock/Latches Lockwood: 8530 – 425 Sc double action latch

with a Padde N.E. latch (part no: FOH00103) in head of frame

Push/Pull Plates Boyd: 1515 sss push plate V/F Sengraved “PUSH” – black Boyd: 1509 sss pull handle C/F engraved “PULL” black

Door Closer Connected to LCN: 4313ME Sentronic (<900mm leaf) LCN; 4314ME Sentronic (>900m leaf)

Reed Switch x 2 Mimic Panel Sentrol: 1078 Reed switch Hinges Satin stainless steel fixed pin hinges

C.5.2.1.3 Type 2C - Stairwells

Lock/Latches (Non Secure)

Lockwood: 8530 – 425 Sc double action latch with a Padde N.E. latch (part no: FOH00103) in head of frame

Push/Pull Plates Boyd: 1515 sss push plate V/F Sengraved “PUSH” – black Boyd: 1509 sss pull handle C/F engraved “PULL” black

Door Closer Connected to LCN: 4313ME Sentronic (<900mm leaf) LCN; 4314ME Sentronic (>900m leaf)

Reed Switch x 2 Mimic Panel Sentrol: 1078 Reed switch Hinges Satin stainless steel fixed pin hinges

Or

C.5.2.1.4 Type 2C - Stairwells

Lock/Latches (secure) Schlage: ND94PD Vandlgard (classroom)

Rhodes 700mm backset, scp (on active leaf) (“T” section meeting stiles”

Panic Bars (secure doors only) Von Duprin: 2227 EOF silver finish (inactive leaf)

Door Closers LCN: Super stock 1461 scp Sequence Closer Glynn Johnson: Cor 2 x FB series Door Stop Boyd: DS 110 scp Hinges Satin stainless steel fixed pin hinges

UNSW

12/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

C.5.2.1.5 Type 2C - Switchboards “T” Section Meeting Stiles

Lock/Latches Boyd: 391 cylinder with

EFCO: 507 R.N.L. scp Door Closer LCN: Super stock 1461 scp Sequence Closer Glynn Johnson: Cor 2 x FB series Latches Sabre: 940 scp auto flush bolts Hinges Satin stainless steel fixed pin hinges

C.5.3 Type 3 - Single Leaf Solid Core Signage: UNSW standard Keying by UNSW locksmiths

C.5.3.1.1 Options Available for Quality/Security

Option 1 Commercial quality

Maximum security Minimum 40mm door thickness Schlage: Vandlgard locksets used

Option 2 Commercial Quality Maximum security Nominal 40mm door thickness Schlage: Vandlgard locksets used with packing plates

Option 3 Light commercial Low security Minimum 38mm door thickness Schlage: AL series locksets used

C.5.3.2 Type 3 - Hardware & Lock Selection

C.5.3.2.1 Type 3A - Office (Option 1)

Commercial Quality Maximum security door thickness 40mm

MINIMUM Lock/Latches Schlage: ND92PD (entrance)

Rhodes 70mm backset, scp finish Door Closer (if required) LCN: Super stock 1461 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Hinges Satin stainless steel fixed pin hinges

C.5.3.2.2 Type 3A - Office (Option 2)

UNSW

13/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Commercial Quality Maximum security door thickness 40mm

NOMINAL Lock/Latches Schlage: ND92PD (entrance)

Rhodes 70mm backset, scp finish with plates Door Closer (if required) LCN: Super stock 1461 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Hinges Satin stainless steel fixed pin hinges

C.5.3.2.3 Type 3A - Office (Option 3)

Light Commercial Low security door thickness 38mm MINIMUM Lock/Latches Schlage: AL53PD Saturn 70mm backset, scp

finish Door Closer (if required) LCN: Super stock 1461 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Hinges Satin stainless steel fixed pin hinges

C.5.3.2.4 Type 3B - Lecture Rooms, Classroom (Option 1)

Commercial Quality Maximum security door thickness 40mm

MINIMUM Lock/Latches Schlage: ND94PD (classroom)

Rhodes: 70mm backset, scp finish Door Closer (if required) LCN: Super stock 1461 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Security Viewer (Blackout)

EFCO: Security viewer (reversed) x 2 One (1) at 1000 high One (1) at 1600 high

Hinges Satin stainless steel fixed pin hinges

C.5.3.2.5 Type 3B - Lecture Rooms, Classroom (Option 2)

Commercial Quality Maximum security door thickness 40mm

NOMINAL Lock/Latches Schlage: ND94PD (classroom)

Rhodes: 70mm backset, scp finish Door Closer (if required) LCN: Super stock1460 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp

UNSW

14/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Security Viewer (Blackout)

EFCO: Security viewer (reversed) x 2 One (1) at 1000 high One (1) at 1600 high

Highes Satin stainless steel fixed pin hinges

C.5.3.2.6 Type 3B - Lecture Rooms, Classroom (Option CATS) Electric Strike

Commercial Quality Maximum security door thickness 40mm

MINIMUM Lock/Latches Schlage: ND96PD (Storeroom)

Rhodes 70mm backset, scp finish Electric Strike Padde: ES 2000 Door Closer LCN: Super stock 1460 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Security Viewer (Blackout)

EFCO: Security viewer (reversed) x 2 One (1) at 1000 high One (1) at 1600 high

Hinges Satin stainless steel fixed pin hinges Note: If Cardax access is required, see Section B

C.5.3.2.7 Type 3C - Emergency Egress Doors (Stairwells Secure Areas)

Lock/Latches (Panic bar, if required)

Von Duprin: 2227 EOF (panic bar) silver finish

Door Closer LCN: Super stock 1461 scp Reed Switch Sentrol: 1078 reed switch (connected to

Cardax) see Section BDoor Stop Boyd: DS 110 scp Hinges Satin stainless steel pin hinges

C.5.4 Type 4 - Double Leaf Solid Core 40mm minimum timber rebate Signage: UNSW standard Keying by UNSW locksmiths To be specified as required.

C.5.5 Type 5 - Auto Sliding Doors Frameless and Aluminium

C.5.5.1 Preferred Suppliers and Installers: Auto Entry FRB Industries Pty Ltd

UNSW

15/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Unit 1/391 Park Road Regents Park NSW 2143

02 9644 2000 02 9645 6977

oentry @ msn.com.au

121 Bath Road Kirrawee NSW 2232 02 9545 1611 02 9545 1616

C.5.5.2 Type 5 - Hardware & Lock Selection

C.5.5.2.1 Type 5A

Main Entry Doors to Building Note: If Cardax access is required, see Section B

C.5.5.2.2 Type 5B

Emergency Egress Doors (Normally Closed - Aluminium)

Lock/Latches (Panic bars x 2)

Von Duprin: 33277 EOF

Door Closer x 2 LCN: Super stock 1461 scp Reed Switch (Connected to Cardax)

Sentrol: 1078 reed switch (1 per leaf)

Hinges Satin stainless steel fixed pin hinges

C.5.6 Type 6 - Double Leaf Aluminium Doors (1 Leaf fixed with mid rail)

C.5.6.1 Type 6 - Hardware & Lock Selection

C.5.6.1.1 Type 6A

C.5.6.1.1.1 Entry Doors to Departments/Sections/Retail

Lock/Latches Lockwood: 3570 Series Mortice lock Aluminium frame section must accommodate 114mm stile.

Lever Furniture (Cylinder hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closers LCN: Super stock 1461 scp Flush Bolts x 2 Doric: DN 201 flush bolts

(inactive leaf – edge side) Or Sabre: 940 auto flush bolts

UNSW

16/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

(inactive leaf – edge side) Or Von Duprin: 33277 EOF (Inactive leaf – edge side)

Door Stop Boyd: DS 110 scp Electric Strike (If required) Padde: ES 2000 Hinges Satin stainless steel fixed pin hinges

Note: If Cardax access is required, see Section B

C.5.6.1.1.2 Adams Rite 4710 Deadlatch (various backsets available) Short backset Mortice Lock

4066 Thumbturn Inside (Optional) 4590 Deadlatch Paddle Inside (Optional) 4560 Deadlatch Handle Inside (Optional)

UNSW Cylinder on outside

C.5.6.1.1.3 1850 Deadbolt (Various backsets available)

4066 Thumbturn Inside (Optional)UNSW Cylinder on outside

C.5.7 Type 7 - Single Leaf Aluminium Doors (with Mid Rail)

C.5.7.1 Type 7 - Hardware & Lock Selection

C.5.7.1.1 Type 7A

C.5.7.1.1.1 Office

Lock/Latches Lockwood: 3570 Series Mortice lock Aluminium frame section must accommodate 114mm stile.

Lever Furniture (Cylinder hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closers LCN: Super stock 1461 scp Door Stop Boyd: DS 110 scp Electric Strike (If required) Padde: ES 2000 Hinges Satin stainless steel fixed pin hinges

UNSW

17/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

C.5.7.1.1.2 Adam Rite 4710 Deadlatch (various backsets available) short backset Mortice Lock.

4066 Thumbturn Inside (Optional) 4590 Deadlatch Paddle Inside (Optional) 4560 Deadlatch Handle Inside (Optional)

UNSW Cylinder on outside

C.5.7.1.1.3 1850 Deadbolt (various backsets available)

4066 Thumbturn Inside (Optional) UNSW Cylinder on outside

C.6 NEW BUILDINGS (Lockwood Version)

C.6.1 Type 1 - Single Leaf Fire Doors 45mm to 50mm "E" core Signage: refer to BCA Clause D2.23 Keying by UNSW Locksmiths

C.6.1.1 Type 1 - Fire Door & Frame Design: Doors must be constructed with;

• Solid steel (NON PERFERATED) metal plates to include; • Hinge plates. • Lock boxes. • Door closer plates.

These are to provide adequate fixings & strength for maintenance purposes. Frames must have:

• Screw fixes hinges into jambs. To be drilled & tapped. • No welded hinges or weld in hinges are to be used.

C.6.1.2 Type 1 - Hardware & Lock Selection

C.6.1.2.1 Type 1A - Plantrooms UNSW

18/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Electronic Mortice Lock Lockwood 3572ELEM1 (left or right) Lever Furniture (Cylinder hole) Lockwood 1801/70 SC with LED Lever Furniture Lockwood 1905/70 SC Door Closer Lockwood 7726 SSS Power Transfer Hinge Lockwood LC8810CP Swipe Card Cardax 3: Card reader Door Stop Lockwood A250 SCP 100 X 100 X 2.5 Hinges x 3 Lockwood 10000BB SSS

C.6.1.2.2 Type 1B - Switchboards Cupboards (Non Walk-in)

Storeroom Mortice Lock Lockwood 3572X (left or right) Lock Turn-snib Adaptor Lockwood SP3570-6050 Lever Furniture (Cylinder hole) Lockwood 1801/70 SC Lever Furniture (Turn-snib) Lockwood 1906 SC Door Closer Lockwood 2024BC SIL 100 X 100 X 2.5 Hinges x 3 Lockwood 10000BB SSS

C.6.1.2.3 Type 1B1 - Service Cupboards (Walk-in)

Storeroom Mortice Lock Lockwood 3572X (left or right) Lever Furniture (Cylinder hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closer Lockwood 2024BC SIL Door Stop Lockwood A250 SCP 100 X 100 X 2.5 Hinges x 3 Lockwood 10000BB SSS

C.6.1.2.4 Type 1C – Fire Stairs (Option 1 Non-Secure)

162 X 162 Push Plate (“PUSH”) Lockwood 20007WN SSS 162 X 162 Pull Plate (“PULL”) Lockwood 20124XN/16 SSS Top Latch with Non-Electric Strike Lockwood 8530-105 & Padde NE Door Closer Lockwood 7726 SSS Floor Door Stop Lockwood A250 SCP 100 X 100 X 2.5 Hinges x 3 Lockwood 10000BB SSS

UNSW

19/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

C.6.1.2.5 Type 1C – Fire Stair / Corridor (Option 2 Secure)

Mechanical Storeroom Mortice Lock Lockwood 3572X (left or right) Lever Furniture (Cylinder hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closer Lockwood 7726 SSS Floor Door Stop Lockwood A250 SCP 100 X 100 X 2.5 Hinges x 3 Lockwood 10000BB SSS

Electronic Access Control

Electronic Mortice Lock Lockwood 3572ELEM1 (left or right) Lever Furniture (Cylinder hole) Lockwood 1801/70 SC with LED Lever Furniture Lockwood 1905/70 SC Door Closer Lockwood 7726 SSS Power Transfer Hinge Lockwood LC8810CP Swipe Card Cardax MkIV Smartswipe Door Stop Lockwood A250 SCP 100 X 100 X 2.5 Hinges x 3 Lockwood 10000BB SSS

C.6.1.2.6 Type 1D - Office (if required)

Storeroom Mortice Lock Lockwood 3572X (left or right) Lever Furniture (Cylinder hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closer Lockwood 7726 SSS Floor Door Stop Lockwood A250 SCP 100 X 100 X 2.5 Hinges x 3 Lockwood 10000BB SSS

C.6.1.2.7 Type 1 - Duct Access Panel (“E Core” Fire Door Panel)

Lock/Latches Boyd: 391 cylinder with EFCO 507 R.N.L. scp Door Closer LCN: Super stock 1461 scp Hinges Satin stainless steel fixed pin hinges

C.6.1.2.8 Type 1 - Duct “Trafalgar” Duct Access Panel

UNSW

Lock/Latches Boyd: 391 cylinder with EFCO 507 R.N.L. scp Hinges Satin stainless steel fixed pin hinges

20/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Note: All other furniture to be supplied by Trafalgar Pty Ltd

C.6.2 Type 2 - Double Leaf Fire Doors 45mm to 50mm – “E” core Signage: Refer BCA Clause D2.23 Keying by UNSW Locksmiths

C.6.2.1 Type 2 - Hardware & Lock Selection

C.6.2.1.1 Type 2A - Plantrooms “T” Section Meeting Stiles

Electronic Mortice Lock Lockwood 3572ELEM1 (left or right) Lever Furniture (Cylinder hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Automatic Flush Bolt Sabre 940 SSS Floor Ferrule Doric DN205 Door Coordinator Glynn Johnson COR-2 Filler Bar Glynn Johnson FB Door Closer Lockwood 7726 SSS Power Transfer Device Lockwood LC8810CP Swipe Card Cardax 3: Card reader Door Stop Lockwood A250 SCP 100 X 100 X 2.5 Hinges x 3 Lockwood 10000BB SSS

C.6.2.1.2 Type 2B - Fire Isolated Passages / Fire Stair - Bullnose Meeting Stiles (Non Secure)

162 X 162 Push Plate (“PUSH”) Lockwood 20007WN SSS 162 X 162 Pull Plate (“PULL”) Lockwood 20124XN/16 SSS Top Latch with Non-Electric Strike Lockwood 8530-105 & Padde NE Top Latch with Double Bevel Roller Strike

Lockwood 8530-305 & Padde DB

Door Closer Lockwood 7726 SSS Floor Door Stop Lockwood A250 SCP 100 X 100 X 2.5 Hinges x 3 Lockwood 10000BB SSS

C.6.2.1.3 Type 2C - Fire Isolated Passages / Fire Stair - Rebate Meeting Stiles (Non Secure)

UNSW

21/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

162 X 162 Push Plate (“PUSH”) Lockwood 20007WN SSS 162 X 162 Pull Plate (“PULL”) Lockwood 20124XN/16 SSS Top Latch with Non-Electric Strike Lockwood 8530-105 & Padde NE Top Latch with Double Bevel Roller Strike

Lockwood 8530-305 & Padde DB

Door Closer Lockwood 7726 SSS Door Coordinator Glynn Johnson COR-2 Filler Bar Glynn Johnson FB Floor Door Stop Lockwood A250 SCP 100 X 100 X 2.5 Hinges x 3 Lockwood 10000BB SSS

C.6.2.1.4 Type 2C - Switchboards “T” Section Meeting Stiles

Lock/Latches Boyd: 391 cylinder with

EFCO: 507 R.N.L. scp Door Closer LCN: Super stock 1461 scp Sequence Closer Glynn Johnson: Cor 2 x FB series Latches Sabre: 940 scp auto flush bolts Hinges Satin stainless steel fixed pin hinges

C.6.3 Type 3 - Single Leaf Solid Core Signage: UNSW standard Keying by UNSW locksmiths

C.6.3.1.1 Options Available for Quality/Security

Option 1 Commercial quality

Maximum security Minimum 40mm door thickness Lockwood 3572Z SC

Option 2 Commercial Quality Maximum security Nominal 40mm door thickness Lockwood 3572Z SC

Option 3 Light commercial Low security Minimum 38mm door thickness Lockwood 3572Z SC

UNSW

22/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

C.6.3.2 Type 3 - Hardware & Lock Selection

C.6.3.2.1 Type 3A - Office (Option 1)

Commercial Quality Maximum security door thickness 40mm

MINIMUM Mortise Lock Lockwood 3572Z SC Lever Furniture (Cylinder Hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closer (if required) LCN Super Stock 1461 SCP Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Hinges Satin stainless steel fixed pin hinges

C.6.3.2.2 Type 3A - Office (Option 2)

Commercial Quality Maximum security door thickness 40mm

NOMINAL Mortise Lock Lockwood 3572Z SC Lever Furniture (Cylinder Hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closer (if required) LCN: Super stock 1461 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Hinges Satin stainless steel fixed pin hinges

C.6.3.2.3 Type 3A - Office (Option 3)

Light Commercial Low security door thickness 38mm MINIMUM Mortise Lock Lockwood 3572Z SC Lever Furniture (Cylinder Hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closer (if required) LCN: Super stock 1461 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Hinges Satin stainless steel fixed pin hinges

C.6.3.2.4 Type 3B - Lecture Rooms, Classroom (Option 1)

Commercial Quality Maximum security door thickness 40mm

MINIMUM

UNSW

23/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Mortise Lock Lockwood 3572X SC Lever Furniture (Cylinder Hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closer (if required) LCN: Super stock 1461 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Security Viewer (Blackout)

EFCO: Security viewer (reversed) x 2 One (1) at 1000 high One (1) at 1600 high

Hinges Satin stainless steel fixed pin hinges

C.6.3.2.5 Type 3B - Lecture Rooms, Classroom (Option 2)

Commercial Quality Maximum security door thickness 40mm

NOMINAL Mortise Lock Lockwood 3572X SC Lever Furniture (Cylinder Hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closer (if required) LCN: Super stock1460 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Security Viewer (Blackout)

EFCO: Security viewer (reversed) x 2 One (1) at 1000 high One (1) at 1600 high

Highes Satin stainless steel fixed pin hinges

C.6.3.2.6 Type 3B - Lecture Rooms, Classroom (Option CATS) Electric Strike

Commercial Quality Maximum security door thickness 40mm

MINIMUM Mortise Lock Lockwood 3572Z SC Lever Furniture (Cylinder Hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Electric Strike Padde: ES 2000 Swipe Card Cardax 3: Card Reader Door Closer LCN: Super stock 1460 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Security Viewer (Blackout)

EFCO: Security viewer (reversed) x 2 One (1) at 1000 high One (1) at 1600 high

Hinges Satin stainless steel fixed pin hinges Note: If Cardax access is required, see Section B

UNSW

24/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

C.6.3.2.7 Type 3C - Emergency Egress Doors (Stairwells Secure Areas)

Lock/Latches (Panic bar, if required)

Von Duprin: 2227 EOF (panic bar) silver finish

Door Closer LCN: Super stock 1461 scp Reed Switch Sentrol: 1078 reed switch (connected to

Cardax) see Section BDoor Stop Boyd: DS 110 scp Hinges Satin stainless steel pin hinges

C.6.4 Type 4 - Double Leaf Solid Core 40mm minimum rebate section Signage: UNSW standard Keying by UNSW locksmiths To be specified as required.

C.6.5 Type 5 - Auto Sliding Doors Frameless and Aluminium

C.6.5.1 Preferred Suppliers and Installers: Auto Entry Unit 1/391 Park Road Regents Park NSW 2143

02 9644 2000 02 9645 6977

oentry @ msn.com.au

FRB Industries Pty Ltd 121 Bath Road Kirrawee NSW 2232 02 9545 1611 02 9545 1616

C.6.5.2 Type 5 - Hardware & Lock Selection

C.6.5.2.1 Type 5A

Main Entry Doors to Building Note: If Cardax access is required, see Section B

C.6.5.2.2 Type 5B

Emergency Egress Doors (Normally Closed - Aluminium)

Lock/Latches (Panic bars x 2)

Von Duprin: 33277 EOF

Door Closer x 2 LCN: Super stock 1461 scp Reed Switch (Connected to Cardax)

Sentrol: 1078 reed switch (1 per leaf)

UNSW

25/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Hinges Satin stainless steel fixed pin hinges

C.6.6 Type 6 - Double Leaf Aluminium Doors (1 Leaf fixed with mid rail)

C.6.6.1 Type 6 - Hardware & Lock Selection

C.6.6.1.1 Type 6A

Aluminium door stiles to be sized in width to suit Lockwood 3572 series mortise lock.

C.6.6.1.1.1 Entry Doors to Departments/Sections/Retail

Lock/Latches Lockwood 3572Z SC (classroom) Or Lockwood 3572Z SC (entrance) Or Lockwood 3572 SC (storeroom)

Lever Furniture (Cylinder hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Door Closers LCN: Super stock 1461 scp Flush Bolts x 2 Doric: DN 201 flush bolts

(inactive leaf – edge side) Or Sabre: 940 auto flush bolts (inactive leaf – edge side) Or Von Duprin: 33277 EOF (Inactive leaf – edge side)

Door Stop Boyd: DS 110 scp Hinges Satin stainless steel fixed pin hinges

C.6.6.1.1.2 Entry Doors to Departments/Sections/Retail (Electronic Access)

Electronic Mortise Lock (for Classroom, Entrance & Storeroom applications)

Lockwood 3572ELEN1 SC

Lever Furniture (Cylinder hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Swipe Card Cardax 3: Card Reader Door Closers LCN: Super stock 1461 scp Flush Bolts x 2 Doric: DN 201 flush bolts

(inactive leaf – edge side)

UNSW

26/27

Design & Construction Requirements (Rev 5)

Last Updated July 2007

Or Sabre: 940 auto flush bolts (inactive leaf – edge side) Or Von Duprin: 33277 EOF (Inactive leaf – edge side)

Door Stop Boyd: DS 110 scp Hinges Satin stainless steel fixed pin hinges

C.7 SIGNAGE

C.7.1 Background The University of New South Wales has a standardised and cohesive signage system based on overall simple rectilinear shapes using standardised typeface, colours and sizes. Signs are classified into types each with an individual specific function.

The UNSW Signage Coordination Officer has the role of directing location specific and detailed design, based on the University’s signage standard (manual). The role includes briefing and liaising with the project team in the pre-construction phase of projects and the engagement and directing of the nominated signage sub-contractor during the construction phase. The signage officer is to be involved prior to the commencement of the documentation phase of any project.

Enquiries and requests should be directed to:

Ricardo Artigas Signage Coordination Officer. Campus Services

C.7.2 General Aluminium is the preferred construction material for all signs. Sign message panels will be rigid, stable and not subject to distortion or corrosion. Support posts for freestanding signs will utilise purpose designed aluminium extrusion to allow the use of inter-changeable sign faces. All fixing devices are to be tamper-resistant and where possible concealed. Approved direct photo deposit methods of reproduction are preferred for symbol and text elements. Intended methods of manufacture and installation should be clearly specified.

UNSW

27/27

Design & Construction Requirements (Rev 5)