SEBAL Expert Training
description
Transcript of SEBAL Expert Training
![Page 1: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/1.jpg)
SEBAL Expert Training
Presented by
The University of Idaho and
The Idaho Department of Water Resources
Aug. 19-23, 2002
Idaho State University
Pocatello, ID
![Page 2: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/2.jpg)
The Trainers
Richard G. Allen,University of Idaho,
Kimberly Research Station
Wim M. Bastiaanssen
WaterWatch,Wageningen, The Netherlands
Ralf Waters
![Page 3: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/3.jpg)
SEBAL
Surface Energy Balance Algorithm for Land Developed by
– Dr. Wim Bastiaanssen, International Institute for Aerospace Survey and Earth Sciences, The Netherlands
applied in a wide range of international settings
brought to the U.S. by Univ. Idaho in 2000 in cooperation with Idaho Department of Water Resources and NASA/Raytheon
![Page 4: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/4.jpg)
Why Satellites?
Typical method for ET:– weather data are gathered from fixed points -- assumed to
extrapolate over large areas– “crop coefficients” assume “well-watered” situation
(impacts of stress are difficult to quantify)
Satellite imagery:– energy balance is applied at each “pixel” to map spatial
variation– areas where water shortage reduces ET are identified– little or no ground data are required– valid for natural vegetation
![Page 5: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/5.jpg)
Definition of Remote Sensing:
The art and science of acquiring information using anon-contact device
![Page 6: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/6.jpg)
SEBAL
UI/IDWR Modifications– digital elevation models for radiation balances in
mountains(using slope / aspect / sun angle)
– ET at known points tied to alfalfa reference using weather data from Agrimet
– testing with lysimeter (ET) data from Bear River basin (during 2000) from USDA-ARS at Kimberly (during 2001)
![Page 7: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/7.jpg)
How SEBAL Works
SEBAL keys off:– reflectance of light energy– vegetation indices– surface temperature– relative variation in surface temperature– general wind speed (from ground station)
![Page 8: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/8.jpg)
Satellite Compatibility
SEBAL needs both short wave and thermal bands
SEBAL can use images from:– NASA-Landsat (30 m, each 8 or 16 days)
- since 1982
– NOAA-AVHRR (advanced very high resolution radiometer) (1 km, daily) - since 1980’s
– NASA-MODIS (moderate resolution imaging spectroradiometer) (500 m, daily) - since 1999
– NASA-ASTER (Advanced Spaceborne Thermal Emission and Reflection Radiometer) (15 m, 8 days) - since 1999
![Page 9: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/9.jpg)
Image Processing
ERDAS Imagine used to process Landsat images
• SEBAL equations programmed and edited in Model Maker function
• 20 functions / steps run per image
![Page 10: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/10.jpg)
Various amounts of reflection
Wavelength in Microns0 0.4 0.6 0.8 1.2 1.6 2.0 2.4
Band: 1 2 3 4 5 7
Visible Near Infrared
Landsat Band 6 is the long-wave “thermal” band and is used for surface temperature
What Landsat Sees
Land Surface
![Page 11: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/11.jpg)
Evapotranspiration at time of overpass
Oakley Fan, Idaho, July 7, 1989
What We Can See With SEBAL
![Page 12: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/12.jpg)
Uses of ET Maps
Extension / Verification of Pumping or Diversion Records
Recharge to the Snake Plain Aquifer Feedback to Producers regarding crop
health and impacts of irrigation uniformity and adequacy
![Page 13: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/13.jpg)
Why Use SEBAL?
ET via Satellite using SEBAL can provide dependable (i.e. accurate) information
ET can be determined remotely ET can be determined over large spatial
scales ET can be aggregated over space and time
![Page 14: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/14.jpg)
Future Applications
ET from natural systems– wetlands– rangeland– forests/mountains
use scintillometers and eddy correlation to improve elevation-impacted algorithms in SEBAL
– hazardous waste sites ET from cities
– changes in ET as land use changes
![Page 15: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/15.jpg)
![Page 16: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/16.jpg)
![Page 17: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/17.jpg)
Reflected
![Page 18: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/18.jpg)
Net Radiation = radiation in – radiation out
![Page 19: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/19.jpg)
ET is calculated as a “residual” of the energy balance
ET = R - G - Hn
Rn
G
H ET
The energy balance includes all major sources (Rn) and consumers (ET, G, H) of energy
Basic Truth: Evaporation consumes Energy
Energy Balance for ET
![Page 20: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/20.jpg)
Vegetation Surface
ShortwaveRadiation
LongwaveRadiation
RSRS
(Incident shortwave)
(Reflected shortwave)
RL
(Incident longwave)
(1-o)RL
RL
(emitted longwave)
(reflected longwave)
Net Surface Radiation = Gains – Losses
Rn = (1-)RS + RL - RL - (1-o)RL
Surface Radiation Balance
![Page 21: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/21.jpg)
Preparing the Image
A layered spectral band image is created from the geo-rectified disk using ERDAS Imagine software.
A subset image is created if a smaller area is to be studied.
![Page 22: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/22.jpg)
Layering – Landsat 7
Band 6 (low & high)
Bands 1-5,7
![Page 23: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/23.jpg)
Bands 1-7 in order
Layering – Landsat 5
![Page 24: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/24.jpg)
Final Layering Order – Landsat 5
![Page 25: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/25.jpg)
Creating a Subset Image
![Page 26: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/26.jpg)
Creating a Subset Image
![Page 27: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/27.jpg)
Obtaining Header File Information
Get the following from the header file:
– Overpass date and time– Latitude and Longitude of image center– Sun elevation angle (b) at overpass time– Gain and bias ofr each and (Landsat 7 only)
![Page 28: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/28.jpg)
Method A
Applicable for these satellites and formats:
– Landsat 5 if original image in NLAPS format– Landsat 7 ETM+ if original image is NLAPS or
FAST
![Page 29: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/29.jpg)
Locating the Header File for Landsat 7ETM+
![Page 30: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/30.jpg)
Locating the Header File for Landsat 5TM
![Page 31: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/31.jpg)
Acquiring Header File Information (Landsat 5 - Method A)
GWT
![Page 32: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/32.jpg)
Biases Gains
Header File for Landsat 7 (bands 1-5,7)
![Page 33: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/33.jpg)
Header File for Landsat 7 (band 6)
GainsBiases
Low gain
High gain
![Page 34: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/34.jpg)
Header File for Landsat 7 (latitude and sun elevation)
![Page 35: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/35.jpg)
DOY
GWT
Acquiring Header File Information (Method B)
![Page 36: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/36.jpg)
Example of Weather Data
![Page 37: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/37.jpg)
Reference ET Definition File of REF-ET Software
![Page 38: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/38.jpg)
Ref-ET Weather Station Data
![Page 39: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/39.jpg)
Ref-ET Output and Equations
![Page 40: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/40.jpg)
Reference ET Results
![Page 41: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/41.jpg)
![Page 42: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/42.jpg)
hours13112t 2
timage (Local Time) = 17:57 – 7:00 = 10:57 am
DSTperiodtimelocalimage
1 FlagtFlag2
1
t
tt
)(
int
ttt 12
t1 = int 10+57/60 + ½ - 0 (1) + 1 = 12 hours
1
For August 22, 2000: image time is 17:57 GMT
Apply the correction:
Calculating the Wind Speed for the Time of the Image
Δt = 1
![Page 43: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/43.jpg)
Estimate Wind Speed at 10:57 am
Interpolate between the value for 12:00 (1.4 m/s) and the value for 13:00 (1.9 m/s)
• U = 1.4+(1.9-1.4)[(10+57/60) – (10+1/2)] = 1.63 m/s
• To estimate ETr for 10:57 AM:Interpolate between the values for 12:00 (.59) and
for 13:00 (.72)
• ETr = .59+(.72-.59) [(10+57/60) – (10+1/2)] = 0.65 mm/hr
![Page 44: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/44.jpg)
Vegetation Surface
ShortwaveRadiation
LongwaveRadiation
RS
RS
(Incident shortwave)
(Reflected shortwave)
RL
(Incident longwave)
(1-o)RL RL
(emitted longwave)
(reflected longwave)
Net Surface Radiation = Gains – Losses
Rn = (1-)RS + RL - RL - (1-o)RL
Surface Radiation Balance
![Page 45: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/45.jpg)
RS↓ calculator
RL↑ model_09
RL↓ calculator
to
a model_03
TS model_08
model_06
model_02
Tbb model_07
L model_01
model_04
NDVI SAVI LAI model_05
Rn = (1-RS↓ + RL↓ - RL↑ - (1-RL↓
Flow Chart – Net Surface Radiation
![Page 46: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/46.jpg)
LMINDNLMINLMAX
L
255
Radiance Equation for Landsat 5
![Page 47: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/47.jpg)
L = (Gain × DN) + Bias
Radiance Equation for Landsat 7
![Page 48: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/48.jpg)
Model 01 – Radiance for Landsat 7c
![Page 49: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/49.jpg)
Enter values from Table 6.1 in Appendix 6
Model 01 – Radiance for Landsat 5
![Page 50: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/50.jpg)
LMINDNLMINLMAX
L
255
Writing the Model for Radiance
![Page 51: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/51.jpg)
rdESUN
L
cos
Reflectivity Equation
365
2DOYcos033.01d r
For August 22, 2000: Sun elevation angle () = 51.560, = (90 - ) = 38.440
DOY = 235, dr = 0.980
![Page 52: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/52.jpg)
Model_02 - ReflectivityFrom Table 6.3
![Page 53: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/53.jpg)
Writing the Model for Reflectivity
rdESUN
L
cos
![Page 54: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/54.jpg)
Top of Atmosphere
Land Surface
Air
Sun
Satellite Sensor
Solar Radiation Reflectance at Land Surface
Reflectance at air
Solar Radiation and Reflectance
![Page 55: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/55.jpg)
toa = Σ (×)
Albedo for the Top of Atmosphere
ESUN
ESUN
![Page 56: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/56.jpg)
Model_03 - Albedo for the Top of Atmosphere
From Table 6.4
![Page 57: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/57.jpg)
2
_
sw
radiancepathtoa
Surface Albedo Equation
sw = 0.75 + 2 × 10-5 × z
For Kimberly: z = 1195 meters,sw = 0.774
path_radiance ~ 0.03
![Page 58: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/58.jpg)
Model_04 - Surface Albedo
![Page 59: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/59.jpg)
Albedo: White is high (0.6) Dark blue is low (.02)
Surface Albedo Map
![Page 60: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/60.jpg)
Two dark bare fields showing a very low albedo.
Surface Albedo for Bare Fields
![Page 61: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/61.jpg)
Fresh snow 0.80 – 0.85Old snow and ice 0.30 – 0.70Black soil 0.08 – 0.14Clay 0.16 – 0.23White-yellow sand 0.34 – 0.40Gray-white sand 0.18 – 0.23Grass or pasture 0.15 – 0.25Corn field 0.14 – 0.22Rice field 0.17 – 0.22Coniferous forest 0.10 – 0.15Deciduous forest 0.15 – 0.20Water 0.025 – 0.348
(depending on solar elevation angle)
Typical Surface Albedo Valuse
![Page 62: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/62.jpg)
Gsc solar constant (1367 W/m2)
dr inverse squared relative Earth-Sun distance
sw one-way transmissivity
Rs↓ = Gsc × cos ×dr × sw
For August 22, 2000: Rs = 812.2 W/m2
Incoming solar Radiation (Rs )
![Page 63: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/63.jpg)
Vegetation Indices
NDVI = (/ ()
SAVI = (1 + L) (L +
91.0
59.0
69.0ln
IDSAVI
LAI
SAVIID = 1.1(
For Southern Idaho: L = 0.1
We set LAI 6.0
![Page 64: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/64.jpg)
Model_05 – NDVI, SAVI, LAI
![Page 65: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/65.jpg)
NDVI Image
Dark green – high NDVI
Yellow green – low NDVI
![Page 66: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/66.jpg)
LAI Image
Dark green – high LAI
Yellow green – low LAI
![Page 67: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/67.jpg)
Surface Emissivity (o)
0 = 1.009 + 0.047 × ln(NDVI)
For snow; > 0.47, o = 0.999
For water; NDVI < 0, o = 0.999
For desert; o < 0.9, o = 0.9
![Page 68: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/68.jpg)
Model_06 – Surface Emissivity
![Page 69: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/69.jpg)
Effective at Satellite Temperature
1ln
6
1
2
L
K
KTbb
K1 and K2 are given in Table 1 of the manual.
![Page 70: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/70.jpg)
Model_07 – Effective at Satellite Temperature
![Page 71: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/71.jpg)
Surface Temperature
25.00bb
s
TT
Systematic errors that largely self-cancel in SEBAL:
1) Atmospheric transmissivity losses are not accounted for.
2) Thermal radiation from the atmosphere is not accounted for.
Fortunately, in SEBAL, the use of a “floating” air-surface temperature function and the anchoring of ET at well-watered and dry pixels usually eliminates the need to applyatmospheric correction.
![Page 72: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/72.jpg)
Model_08 – Surface Temperature
![Page 73: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/73.jpg)
Surface Temperature Image
Red – hot (600C)
Blue – cold (200C)
![Page 74: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/74.jpg)
Surface Temperature Image
White – cold
Dark red - hot
![Page 75: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/75.jpg)
Outgoing Longwave Radiation (RL)
RL↑ = o σ T4
Where
ε= emissivity
T = absolute radiant temperature in degrees Kelvin
= Stefan-Boltzmann constant (5.67 10-8 W / (m2 – K4)
![Page 76: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/76.jpg)
Model_09 – Outgoing Longwave Radiation
![Page 77: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/77.jpg)
Outgoing Longwave RadiationImage and Histogram
![Page 78: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/78.jpg)
![Page 79: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/79.jpg)
Selection of “Anchor Pixels”
• The SEBAL process utilizes two “anchor” pixels to fix boundary conditions for the energy balance.
• “Cold” pixel: a wet, well-irrigated crop surface with full cover Ts Tair
• “Hot” pixel: a dry, bare agricultural field ET 0
![Page 80: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/80.jpg)
Incoming Longwave Radiation (RL)
• RL↓ = a × σ × Ta4
a = atmospheric emissivity = 0.85 × (-ln tsw).09 for southern Idaho
Ta Tcold at the “cold” pixel
• RL↓ = 0.85 × (-ln sw).09 × σ × Tcold4
• For August 22, 2000: sw = 0.774, Tcold = 292.5 K, RL↓ = 311.0 W/m2
![Page 81: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/81.jpg)
Net Surface Radiation Flux (Rn)
Rn = (1-)RS↓ + RL↓ - RL↑ - (1-o)RL↓
![Page 82: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/82.jpg)
Model_10 – Net Surface Radiation
![Page 83: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/83.jpg)
Net Surface Radiation Image and Histogram
Light – high Rn
Dark – low Rn
![Page 84: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/84.jpg)
Surface Energy Budget Equation
Rn = G + H + ET
ET = Rn – G – H
![Page 85: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/85.jpg)
Soil Heat Flux (G)
G/Rn = Ts/(0.0038)(1 - .98NDVI4)
G = G/Rn Rn
Flag for clear, deep water and snow: If NDVI < 0; assume clear water, G/Rn = 0.5
If Ts < 4 oC and > 0.45; assume snow, G/Rn = 0.5
![Page 86: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/86.jpg)
Model_11 – G/Rn and G
![Page 87: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/87.jpg)
G/Rn Image and Histogram
![Page 88: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/88.jpg)
Soil Heat Flux Image and Histogram
Light – high G
Dark – low G
![Page 89: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/89.jpg)
Surface Type G/Rn
Deep, Clear Water 0.5Snow 0.5Desert 0.2 – 0.4Agriculture 0.05 – 0.15Bare soil 0.2 – 0.4Full cover alfalfa 0.04Clipped Grass 0.1Rock 0.2 – 0.6
G/Rn for Various Surfaces
These values represent daytime conditions
![Page 90: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/90.jpg)
Sensible Heat Flux (H)
H = (×cp × dT) / rah
HrahdT
rah = the aerodynamic resistance to heat transport (s/m).
ku
z
zln
r*
1
2
ah
z1
z2
dT = the near surface temperature difference (K).
![Page 91: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/91.jpg)
om
x
x
z
z
kuu
ln
*
Friction Velocity (u*)
ux is wind speed (m/s) at height zx above ground.
zom is the momentum roughness length (m).
zom can be calculated in many ways:
– For agricultural areas: zom = 0.12 height of vegetation (h)
– From a land-use map– As a function of NDVI and surface albedo
![Page 92: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/92.jpg)
Zero Plane Displacement (d) and Momentum Roughness Length (zom)
The wind speed goes to zero at the height (d + zom).
![Page 93: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/93.jpg)
Calculations for the Weather Station
For August 22, 2000:
zx = 2.0 m, ux = 1.63 m/s,
h = 0.3 m, zom = 0.120.3 = .036 m
u* = 0.166 m/s
k
zuu om
200ln
*200
u200 = 3.49 m/s
![Page 94: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/94.jpg)
Iterative Process to Compute H
![Page 95: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/95.jpg)
omz
kuu
200ln
* 200
Friction Velocity (u*) for Each Pixel
u200 is assumed to be constant for all pixels
zom for each pixel is found from a land-use map
For agricultural fields, zom = 0.12hFor our area, h = 0.15LAIzom = 0.018 × LAI
![Page 96: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/96.jpg)
Model_12 – Roughness Length
Water; zom = 0.0005 m
Manmade structures; zom = 0.1 m
Forests; zom = 0.5 m
Grassland; zom = 0.02 m
Desert with vegetation; zom = 0.1 m
Snow; zom = 0.005 mFor agricultural fields: Zom = 0.018 LAI
![Page 97: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/97.jpg)
Insert coordinates from LAI image
Setting the Size of the Land-use Map
![Page 98: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/98.jpg)
ku
zz
rah
*
ln1
2
Aerodynamic Resistance to Heat Transport (rah) for Each Pixel
z1 height above zero-plane displacement height (d)
of crop canopy z1 0.1 m
z2 below height of surface boundary layer
z2 2.0 m
![Page 99: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/99.jpg)
Model_13 – Friction Velocity and Aerodynamic Resistance to Heat Transport
![Page 100: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/100.jpg)
Near Surface Temperature Difference (dT)
To compute the sensible heat flux (H), define near surface temperature difference (dT) for each pixel
dT = Ts – Ta
Ta is unknown
SEBAL assumes a linear relationship between Ts and dT:
dT = b + aTs
![Page 101: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/101.jpg)
How SEBAL is “Trained”
SEBAL is “trained” for an image by fixing dT at the 2 “anchor” pixels:– At the “cold” pixel: Hcold = Rn – G - ETcold
where ETcold = 1.05 × ETr
dTcold = Hcold × rah / ( × cp)
– At the “hot” pixel: Hhot = Rn – G - EThot where EThot = 0
dThot = Hhot × rah / ( × cp)
![Page 102: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/102.jpg)
How SEBAL is “Trained”
Once Ts and dT are computed for the “anchor” pixels,the relationship dT = b + aTs can be defined.
![Page 103: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/103.jpg)
Graph of dT vs Ts
Correlation coefficients a and b are computed
![Page 104: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/104.jpg)
Sensible Heat Flux (H)
dT for each pixel is computed using: dT = b + aTs
H = (×cp × dT) / rah
![Page 105: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/105.jpg)
Model_14 – Sensible Heat Flux
![Page 106: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/106.jpg)
10oC 10oC10oC
9oC9oC9oC
11oC 11oC11oC12oC
8oC
10oC
11oC
10oC 10oC
10oC
10oC9oC
: Direction of Force
StableNeutralUnstable
StableNeutralUnstable
100m
100m
The direction of force for an sudden movement of air
The tendency of air movement
Atmospheric Stability
![Page 107: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/107.jpg)
ku
z
z
rzh
ah
*
)(1
2
2ln
Stability Correction for u*and rah
• New values for dT are computed for the “anchor” pixels.• New values for a and b are computed.• A corrected value for H is computed.• The stability correction is repeated until H stabilizes.
)200(0
200
200ln
*
mmmz
kuu
![Page 108: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/108.jpg)
![Page 109: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/109.jpg)
Instantaneous ET (ETinst)
ET (W/m2) = Rn – G – H
ET
hrmmETinst 3600)/(
![Page 110: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/110.jpg)
r
inst
ET
ETETrF
Reference ET Fraction (ETrF)
ETr is the reference ET calculated for the time of the image.
For August 22, 2000, ETr = 0.65 mm/hr
![Page 111: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/111.jpg)
Model_25 – Instantaneous ET and ETrF
![Page 112: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/112.jpg)
24-Hour Evapotranspiration (ET24)
24_24 rETETrFET Path 39: Am. Falls -24-hour ET
8/07/00
9/08/01
![Page 113: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/113.jpg)
Seasonal Evapotranspiration (ETseasonal)
Assume ETrF computed for time of image is
constant for entire period represented by image.
Assume ET for entire area of interest changes in proportion to change in ETr at weather station.
![Page 114: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/114.jpg)
Seasonal Evapotranspiration (ETseasonal)
Step 1: Decide the length of the season Step 2: Determine period represented by each satellite image Step 3: Compute the cumulative ETr for period represented by image. Step 4: Compute the cumulative ET for each period
(n = length of period in days)
Step 5: Compute the seasonal ET
n
irperiodrperiod i
ETFETET1
24
ETseasonal = ETperiod
![Page 115: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/115.jpg)
0
100
200
300
400
500
Total
Lysimeter SEBAL
Validation of SEBAL
ET - July-Oct., mm Montpelier, 1985
SEBAL
405 mmLysimeter
388 mm
![Page 116: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/116.jpg)
0100200300400500600700800
Total
Lysimeter SEBAL
Lysimeter
718 mmSEBAL
714 mm
Sugar Beets
Validation of SEBAL
ET - April-Sept., mm - Kimberly, 1989
![Page 117: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/117.jpg)
![Page 118: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/118.jpg)
Conclusions
ET can be determined for a complete year for large areas
ET can be aggregated over space and time
![Page 119: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/119.jpg)
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
Aug-98
Sep-98
Oct-98
Nov-98
Dec-98
Jan-99
Feb-99
Mar-99
Apr-99
May-99
Jun-99
Jul-99
Fra
cti
on
(-)
0
0.2
0.4
0.6
0.8
1
1.2
1.4R
elat
ive
soil
wet
nes
s (-
) Relative w ater supplyOverall consumed ratioRelative soil w etness
The Future
ET maps will be used to assess Irrigation Performance
ET maps and associated products will be used to assess crop productivity
![Page 120: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/120.jpg)
The key is to look up !
![Page 121: SEBAL Expert Training](https://reader031.fdocuments.in/reader031/viewer/2022012406/568153f7550346895dc1f7f6/html5/thumbnails/121.jpg)