Seam Ripper Kit
2
Diagram A - Parts List Seam Ripper Kit #PKSR1 Single Blade (small Style A) #PKSR2 Double Blade (large & small Style B) #PKSRNXX Necklace (Style C) #PKSR3 Stilleto (Style A) Kit Features • Style A - Single Blade, small ripper with clip. Reverses into handle for safety. • Style B - Double Blade, small & large rippers. • Style C single small blade w/ magnetic necklace chain catch. • Sharp blade reverses into handle for safety. • 8mm tubes Required Accessories • 7mm, Pen Mandrel • 8mm Drill Bit #PKPARK-8MM • 8mm Barrel Trimmer (use from #PKTRIMKIT) • 3 pc. Bushings Set #PKSRBU (use 2 of the 3 in the set for each style) • 2 part glue, epoxy or Insta-cure (cyanoacrylate). PSI Woodworking Products PKSRXX Preparing the Blank • Prepare and cut a blank of 3/4” or larger, to the length of the brass tube (add 1/16” for trimming) • Drill a 8mm hole through the center of the blank. • Spread glue over the tube, insert into blank with a twisting motion to spread the glue evenly inside. • Center the tube inside the blank. • When glue is dry. Trim the ends of the blank flush to the tube. Clip Cap Tube style C 2-1/4” Single Blade - Style - A & C Large Seam Ripper Retaining Spring 3-1/8” Double Blade - Style - B Single Blade Necklace Large & Small Blades Larger Blade Smaller Blade Small Blade Stored Position Protective Ball Small Seam Ripper Small Seam Ripper Protective Ball A C B © 2012 PSI Woodworking • Philadelphia, PA 19115 v06/12 Retaining Spring Retaining Spring Magnetic Cap Magnetic Clasp & Chain Tube Style A Style A Style C Style C Tube style A 3-1/8” Stilleto Stilleto
Transcript of Seam Ripper Kit
Diagram A - Parts List
Seam Ripper Kit #PKSR1 Single Blade (small Style A) #PKSR2 Double Blade (large & small Style B) #PKSRNXX Necklace (Style C)#PKSR3 Stilleto (Style A) Kit Features •StyleA-SingleBlade,smallripperwithclip. Reversesintohandleforsafety.•StyleB-DoubleBlade,small&largerippers.•StyleCsinglesmallbladew/magneticnecklacechaincatch.•Sharpbladereversesintohandleforsafety.•8mmtubes
Required Accessories •7mm,PenMandrel•8mmDrillBit#PKPARK-8MM•8mmBarrelTrimmer(usefrom#PKTRIMKIT)•3pc.BushingsSet#PKSRBU(use2ofthe3inthesetforeachstyle)•2partglue,epoxyorInsta-cure(cyanoacrylate).
PSI Woodworking ProductsPKSRXX
Preparing the Blank•Prepareandcutablankof3/4”orlarger,tothelengthofthebrasstube(add1/16”fortrimming)•Drilla8mmholethroughthecenteroftheblank.•Spreadglueoverthetube,insertintoblankwithatwistingmotiontospreadtheglueevenlyinside.•Centerthetubeinsidetheblank.•Whenglueisdry.Trimtheendsoftheblankflushtothetube.
Clip
CapTube style C 2-1/4”
Single Blade - Style - A & C
Large Seam Ripper
Retaining Spring
3-1/8”
Double Blade - Style - B
Single Blade
Necklace
Large & Small Blades
Larger Blade
Smaller Blade
Small Blade
Stored Position
Protective BallSmall Seam Ripper
Small Seam Ripper
Protective Ball
A
C
B
© 2012 PSI Woodworking • Philadelphia, PA 19115 v06/12
Retaining Spring
Retaining Spring
Magnetic Cap
Magnetic Clasp & Chain
Tube
Style A
Style A
Style C
Style C
Tube style A 3-1/8”
Stilleto
Stilleto
Diagram B - Turning the Blank
PSI Woodworking ProductsPKSRXX
© 2012 PSI Woodworking • Philadelphia, PA 19115 v03/12
HeadstockSpacer Bushings Spacer Bushings
End Bushing(Larger)
End Bushing(Smaller) Lock Nut
Live Center
Mandrel
Tube
Use Smaller End Bushing: Style A , CUse Larger End Bushing: Style B
Turning the Blank•PlacethebushingsandblankonthemandrelaccordingtoDiagramB.•UsethelargerendbushingonstyleAandasmallerbushingontheotherend.ForstyleB&Cusethelargerbushingonbothends.•Threadontheknurlednutandhandtightentoholdallitemsinplace.•Slidethetailstocktothemandrelshaft,(donotovertighten,itcoulddamagethemandrel)lockinplace.•Turnthehandleendsdown,flushwiththebushingsusingthelathetools,graduallyincreasing thegradesofsandpaper.•FinishthewoodwithfrictionpolishoruseanyPSIprojectfinishofyourchoice.
AssemblyFor Single style A & C:•Placetheclipovertheextensionofthecap.Pressthisassemblyintothe upperendofthehandlewithsmallerdiameter.•Or(fornecklaceStyleC)Pressthemagneticcap,narrowendinfirstintotheupperendofthebarrel.For Styles A , B & C:•Squeezetheretainingspringtoasmallroundcircle(DONOTCREASE) andinsertintoopeningattheend(s).Pushin,flushtothesurface.•Slidetheseamripperassemblyinandoutwithbothendstoassure asecurefit.•Ifspringdoesnotholdinproperly(i.e.thespringslidesintothetube), TakeaQ-tipanddipintoCAglueinsertthespringandallowtheCA todry.Thespringshouldnowoperateproperly.•Whennotinuse,reversetheripperassemblytosafelystoretheblade(s).•Insertthechainthroughthesmallringonthemagneticbar,locktheclasp.•Insertthebarintothemagneticcap.
Style A & B & C
Diagram E - Bushing #PKSRBU
ø.430"-0 ø.375"-0ø.430"-0
Larger Smaller
ø.248"-0
Hole size
Knurled Nut
