Sche Wiring
Transcript of Sche Wiring
-
8/12/2019 Sche Wiring
1/21PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
2/21
You will need this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep this manual and invoice in a safe and dry place for future reference.
-- - -
- --
1. Cluttered benches and dark areas
invite accidents.
2. - - -- - - - - -- - Power tools create
SKU 96838 -- - PAGE 2
-- - - - - -- -
-- - - - - -
-
Electr ica l Requi rem ents A l ternator Type: S ing le Phase , BrushO u tpu t : 3000W Ra ted / 3500W PeakRa ted Vo l tage : 120 VAC, 20 A m p 60Hz 120 /240 VAC, 12 .5 Amp 60 Hz
A C R ec ep ta c le s : 12 0 V A C , 3- P ro n g G ro u nd in g P lu g (Q ty . 2 )120 /240 VA C, 4-B lade Tw ist lock P lug (Qty. 1)
NEM A L14 -30DC R ecep tac le : 12 VDC O u tpu t Te rm ina l w i th Cap Screws(Qty 1)Ci rcu i t Breaker : 13 Am pOver load Protect ion: Reset tab le Ci rcu i t Pro tect ion
Engine Speci f ica t ions Engine Type: 4-Stroke, Overhead Valve, S ing le Cyl inderEngine Star t Type: Reco i lEng ine Disp lacemen t: 196ccEng ine Speed : 3600 RPMOi l Cap aci ty : 20 Flu id OuncesFuel Type: Un leaded Gasol ineFuel Capaci ty : 3 .96 Gal lonsRecom mended O i l Type : F -SAE 30W (Above 32!)
F -SAE 5W-30W (Be low 32 ! )Run T ime : 15 Hou rs Con t inuous Run T ime on Fu l l Tank @50% LoadEPA Cer t i f ied (Phase I I , Category A)
Ove ra l l Dimensions 21-1 /2 "Long x 16-3 /4 "W ide x 17 -1 /2 " High
Ne t We igh t 98 Pounds
- - - -
- - --
- -
- - -
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
3/21
1. - -- -
- A moment of inattention whileoperating power tools may result in serious personal injury.
2. -- - - - Loose
clothes, jewelry, or long hair can be caught in moving parts.
SKU 96838 -- - PAGE 3
3. - - - - - - -
4. - - - Awrench or a key that is left attached to a rotating part of the machine may result
in personal injury.
5. - Properfooting and balance enables better control of the power tool in unexpected
situations.
6. - - - Always wear
ANSI approved safety impact goggles when using this product. ANSI
approved hearing protection must also be used.
1. - The correcttool will do the job better and safer at the rate for which it is designed.
2. - - - Any tool that cannot be controlled with its power switch is dangerous and
must be replaced.
3. - -- Toolsare dangerous in the hands of untrained users.
4. - Properly maintained tools are less likely to malfunctionand are easier to control. Do not use a damaged tool. Tag damaged
3. -- -- Distractions can cause you to lose control. Provide barriers or shields as
needed.
sparks which may ignite the dust or fumes.
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
4/21
-
- - Many accidents are caused by poorlymaintained tools.
SKU 96838 -- - PAGE 4
6. - --- Accessories that may be suitable for one tool may become hazardous
when used on another tool.
1. - - - Service
or maintenance performed by unqualified personnel could result in a risk of injury.
2. - - - -- - -
Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
1. -
- - - - -
Before each use, check the oil level. Never run the Engine with low or no
engine oil. Running the Engine with low or no oil will permanently damage the
unit.
2. - - These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
5. - - -
tools -until repaired.
3. - - - - - -
4. - - - -
5. - Serious injury could result if the Generator
is tipped.
6. - Turn off theEngine before leaving.
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
5/21
-
8/12/2019 Sche Wiring
6/21
-
2. - - --
-
3. - -
1. - - - --
2. - - - -
If swallowed, seek medical treatment immediately. Do not inducevomiting if fuel is swallowed. For skin contact, immediately wash with soap and
water. For eye contact, immediately flush eyes with clean water.
1. - - - - -
Always wear ANSI approved hearing protection when operating or working
around the Generator when it is running.
SKU 96838 -- - PAGE 6
1. All connections and conduits from the Generator to the load must only be installed
by trained and licensed electricians, and - - --
-
2. -
- --
3. If an extension cord (not included) is used, make sure to use only UL listed cords
having the correct gauge and length.
4. Do not attempt to connect or disconnect load connections while standing in
water, or on wet or soggy ground.
5. Do not touch electrically energized parts of the Generator and interconnecting
cables or conductors with any part of the body, or with any non-insulated
conductive object.
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
7/21
SKU 96838 -- - PAGE 7
7. Be sure the Engine#s Ignition Switch (20) is in its $OFF"position before moving
the Generator before performing any service, maintenance, or cleaning
procedures on the unit.
8. Keep all electrical equipment clean and dry. Replace any wiring where the
insulation is cracked, cut, abraded, or otherwise degraded. Replace terminals
that are worn, discolored, or corroded. Keep terminals clean and tight.
11. Use only Class BC or Class ABC fire extinguishers on electrical fires.
10. Guard against electric shock. Prevent body contact with grounded surfaces such
as pipes, radiators, ranges, and refrigerator enclosures.
9. Insulate all connections and disconnected wires.
6. Connect the Generator only to a load or electrical system (120 volt, 240 volt, or
12 volt) that is compatible with the electrical characteristics and rated capacities
of the Generator.
PDF !"#"pdfFactory" $#%&'( )www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
8/21
MISC. PRECAUTIONS
1. People with pacemakers should consult their physician(s)
before using this product. Operation of electrical equipment in close proximity to
a heart pacemaker could cause interference to or failure of the pacemaker.
2. The warnings and precautions discussed in this manual cannot
cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot
be built into this product, but must be supplied by the operator.
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts Lists on page 17
are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
PRODUCT FEATURES
SKU 96838 For technical questions, please call 1-800-444-3353 PAGE 8
1. 240 VAC Outlet (72): Use to connect electrical devices that run 240 volt, 60 Hz,
single phase, AC current. (See Figure B.)
2. Ground Terminal (10): Connect grounding wires here to properly ground unit.
(See Figure B.)
FIGURE B
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
9/21
3. Used to connect electrical devices that run 120 volt, 60Hz, single phase, AC current.
4. Use to switch between 120 and 240 volt output.
5. Reset switch that protects the Generator from electrical
overload.
6. Use for charging 12 volt, automotive type
batteries only.
7. - Location for checking and filling engine oil.
8. Used to enable starting and stopping of Engine.
9. Pull cord for starting Engine.
10. Traps dirt and water from fuel before it enters Engine.
11. Allows fuel to enter Engine.
12. A removable, cleanable, sponge-like element that limits theamount of dirt pulled into the Engine.
13. Adjusts the amount of air entering the Engine.
14. Indicates the amount of fuel in the Fuel Tank.
15. Provides access to the Fuel Tank for adding fuel.
16. Provides readings of voltage output.
SKU 96838 -- - PAGE 9
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
10/21
-
8/12/2019 Sche Wiring
11/21
-
8/12/2019 Sche Wiring
12/21
SKU 96838 -- - PAGE 12
the amount of unleaded gasoline. When necessary, refill the Fuel Tank, only after
Engine is OFF and cooled down.
3. Periodically, make sure to check the Fuel Filter (46) for excessive dirtand debris. If necessary, remove the Fuel Filter and clean with compressed air.
1. Check to make sure the Ignition Switch (20) is in its position.
2. Make sure to unplug any load from the Generator beforestarting to prevent permanent damage to any appliances, tools, or equipment.
1. Turn the Engine Fuel Valve (78) to its position. Then, turn the Engine
Choke Lever (79) to its position. No choke is required if theEngine is warm. Make sure the Engine Choke Lever is in the positionwhen starting a warm Engine.
2. Turn the Engine Ignition (20) to its position. Grasp the Starter Handle on
the Recoil Starter (75) and pull slowly until resistance is felt. Allow the Rope to
rewind slowly. Then, pull the Handle with a rapid, full arm stroke. Allow the Rope
to rewind slowly. If necessary, repeat this procedure until the Engine starts.
3. When the Engine starts, slowly move the Choke Lever (79) to its position.
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
13/21
SKU 96838 -- - PAGE 13
4. Allow the Generator to run at no load for five minutes after each
start-up so that the Engine and Generator can stabilize.
1. Start the Engine, and allow the Engine and Generator to run and warm up for
five minutes after starting with no electrical load.
2. Connect 120V AC appliances, tools, and equipment to the
two 120 VAC Outlets (71). Connect 240 AC appliances, tools, and equipment
to the one 240 VAC Outlet (72). Connect 12V DC appliances, tools, and
equipment to the 12 VDC Charging Terminal (69).
3. Never exceed the rated capacity for this Generator, as seriousdamage to the Generator and/or appliances, tools, and equipment could result
from an overload. Starting and running wattage requirements should always becalculated when matching this Generator#s wattage capacity to the appliance,
tool, or equipment.
4. Most appliances, tools, and equipment will list on the motor nameplate the
starting and running voltage and amperage requirements. Use the following
formula to convert voltage and amperage to wattage:
5. To determine the approximate wattage requirement for most appliances, tools,
and equipment with $inductive"type motors, multiply the wattage that was
calculated by 2 times to assure adequate Generator capacity.
6. The starting and running wattage for $resistant"loads are the same.Example: a 100 Watt light bulb requires only 100 Watts to start. Most resistant
loads will be listed in wattage.
7. Always power the largest electric motor first. Then, plug in other appliances,
tools, and equipment one at a time.
Connect $inductive" load appliances, tools, and equipment first. Inductive loads consist of small hand tools and some small appliances. Connect the items that require the most wattage first.
Connect any lights next.
Voltage sensitive appliances, tools, and equipment should be the last to beconnected to the Generator. Plug voltage sensitive items such as T.V.#s, VCR#s,
microwaves, and cordless telephones into a UL listed voltage surge protector
(not included). Then, connect the UL Listed surge protector into the Generator.
r
r
- - - - -
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
14/21
SKU 96838 -- - PAGE 14
8. Failure to connect and operate appliances, tools, and equipment
in this sequence can cause damage to the Generator, appliances, tools, and
equipment and will void the warranty on this Generator.
9. Once the Engine is running, simply connect the 120 volt appliances, tools, andequipment into the 120 VAC Outlets (71). Connect a 240 volt appliance, tool, or
equipment into the 240 VAC Outlet (72). Or connect a 12 volt appliance, tool,
or equipment into the 12 VDC Charging Terminal (69).
10. If Engine speed or voltage fluctuates with a load below 250
Watts, move the Engine Choke Lever (79) to the position.
11. When finished using the Generator, disconnect all electrical loads. Close Fuel
Valve (78) until carburetor runs dry, then shut off Ignition Switch (20).
1. Always make sure the Engine#s Ignition Switch (20) is in itsposition prior to performing any service, maintenance, or cleaning of the
Generator or Engine.
2. -inspect the general condition of the Generator and Engine.
Check for loose screws, misalignment or binding of moving parts, cracked or
broken parts, loose hose connections, and any other condition that may affect
the safe operation of the Generator and Engine. If abnormal noise or vibration
occurs, have the problem corrected before further use.
-
3.
Keep the Generator clean and dry at all times.
The Generator should not be operated or stored in locations that include excessive moisture, dust, flammable or corrosive vapors. If these substances
are on the Generator, clean with a cloth or soft brush.
Do not use a garden hose or anything with liquid to clean the Generator.
Liquid may enter the cooling air slots and could damage the interior workings
of the Generator.
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
15/21
SKU 96838 -- - PAGE 15
4.
6. - Before storing, drain all fuel out of theGenerator#s Fuel Tank. If this is not followed, old fuel in the Generator#s Fuel
Tank may clog the Carburetor of the Engine and prevent the Generator from
starting until cleaned out. Then, make sure to store the unit in a clean, dry, safe
location out of reach of children and other unauthorized people.
7. - - - - -
5. For additional reference to the care and maintenance of the Engine,refer to the Engine manufacturer#s service manual.
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
PDF !"#"pdfFactory" $#%&'( )www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
16/21
SKU 96838 -- - PAGE 16
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
17/21
-
8/12/2019 Sche Wiring
18/21
ASSEMBLY DIAGRAM
SKU 96838 For technical questions, please call 1-800-444-3353 PAGE 18
71
72
PDF !"#"pdfFactory" $#%&'( )www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
19/21
WIRING DIAGRAM
SKU 96838 For technical questions, please call 1-800-444-3353 PAGE 19
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
20/21
SKU 96838 -- - PAGE 20
-- - - -- -
The California Air Resources Board (herein CARB), the United States Environmental Protection Agency (herein EPA),
and Harbor Freight Tools% (herein HFT) are pleased to explain the emission control system warranty on your 1995
and later Small Off-Road Engine (herei n engine). In California, the engine must be designed, built and equipped to meetthe State#s stringent anti-smog standards. Elsewhere within the United States, new off-road, spark-ignition engines
certified for model year 1997 and later, must meet similar standards set forth by the EPA. HFT must warrant the
emission control system on your engine for the periods of time described below, provided there has been no abuse,
neglect or improper maintenance of your engine.
Your emission control system may include parts such as the carburetor or fuel-injection system, and the ignition
system. Also included may be hoses, belts, connectors and other emission-related assemblies.
Where a warrantable condition exists, HFT will repair your engine at no cost to you including diagnosis, parts and
labor.
-
The 1995 and later engines are warranted for two (2) years. If any emission-related part on your engine is defective, the
part will be repaired or repl aced by HFT.
- -- -
Engines are warranted for a period of two (2) years relative to emission control parts defects, subject to the provisions set
forth below. If any emission related part on your engine is defective, the part will be repaired or replaced by HFT.
- ---
- As the engine owner, you are responsible for the performance of the required maintenance listed in your Owner#s
Manual. HFT recommends that you retain all r eceipts covering maintenance on your engine, but HFT cannot deny
warranty solely for the lack of receipts or fo r your failure to ensure the performance of all s cheduled maintenance.
- As the engine owner, you should, however, be aware that HFT may deny you warranty coverage if your engine or a part
has failed due to abuse, neglect, improper m aintenance, or unapproved modifications.
- You are responsible for shipping your engine to a HFT warranty station as soon as a problem exists. Contact the HFT
Customer Service department at the number below to make shipping arrangements. The warranty repairs should be
completed in a reasonable amount of t ime, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact the Harbor Freight Tools
Customer Service Department at 1-800-444-3353.
- -- - --
HFT warrants to a first retail purchaser and each subsequent purchaser that the engine is free from defects inmaterials and workmanship that cause the failure of warranted parts for a period of two (2) years after the date
of delivery to the first retail purchaser.
Repair or replacement of any warranted part will be performed at no charge to the owner if the work is performed
through a warranty station authorized by HFT. For emissions warranty service, contact the HFT Customer Service
Department at 1-800-444-3353.
- -
Coverage under this warranty shall also extend to the failure of any engine components caused by the failure of any
warranted part while it is still covered under this warranty.
--
Warranty claims shall be filed in accordance with the provisions of the HFT warranty policy explained in the box
at the top of the previous page. HFT shall not be liable for any loss of use of the engine, for any alternative usage,
for any damage to goods, loss of time, or inconvenience. Warranty coverage shall also be excluded for any part
which fails, malfunctions, or is damaged due to failure to follow the maintenance and operating instructions set
forth in the Owner#s Manual including, but not limited to:
(a) use of parts which are not authorized by HFT
(b) improper installation, adjustment or repair of the engine or of any warranted part unless performed by an
authorized warranty center
(c) failure to follow recommendations on fuel use contained in the Owner#s Manual
(d) improper or inadequate maintenance of any warranted parts
(e) repairs performed outside of the authorized warranty service dealers
(f) alterations by changing, adding to or removing parts from the engine.
PDF !"#"pdfFactory" $#%&'(www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/ -
8/12/2019 Sche Wiring
21/21
SKU 96838 -- - PAGE 21
Component parts which are not scheduled for replacement as required maintenance or are scheduled only for
regular inspection to the effect of $repair or replace as necessary" are warranted for the warranty period. Anywarranted part which is scheduled for replacement as r equired maintenance is warranted for the period of t ime up
to the first scheduled replacement point for that part. Any replacement part, provided it is equivalent in durability
and performance, may be used in performance of maintenance or repairs. The owner is responsible for
commissioning a qualified technician/mechanic to perform all required maintenance, as outlined in the -
section on page 14 and 15 of this manual.
-
-
i ) Carburetor and i ts in terna l parts .
i i) Fuel pump ( if so equipped).
i i i) Cold start enrichment system.
-
i ) Intake p ipe /man ifold.
ii) A ir c le an er.
-i) Spark plug.
i i) Magneto igni t ion sys tem.
- - -
i) Ex ha ust pi pe s tud .
ii) Muffler.
i i i) Catalytic converter ( i f so equipped).
-- - - --
i) Vacuum, temperature and time sensitive valves and switches.
i i) Hoses, belts, connectors, and assemblies.
-- - - -- - --
-- -
- - -- - - -- - - - - - - - - - - -- - - - - - - -- - - - - - - - - -- - - - - - -- - - - - -
- - - - - - - - -- - - - - - -- - - -
- - - - - - - -