Scania Engine Data 1588878
-
Upload
anderson-mylonas -
Category
Documents
-
view
630 -
download
23
Transcript of Scania Engine Data 1588878
031110031015
Engine data
Industrial diesels12-series with EMS
Industrial & Marine Engines
Part No. 1 588 87
Section 5
8 © Scania CV AB Sweden
ContentsEngine program.................................................................................................... 3Standard equipment ............................................................................................. 3Basic data ............................................................................................................. 4Technical data and cooling equipment recommendation..................................... 6
DI12 54A, order ref. 10-70................................................................................ 6DI12 56A, order ref. 10-71................................................................................ 8DI12 56A, order ref. 10-72.............................................................................. 10
Basic dimensionsDI12................................................................................................................. 12
Equipment list .................................................................................................... 14
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
2 © Scania Industrial & Marine Engines 031110Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
031110 © Scania Industrial & Marine Engines
Latest modification date: 031015
Engine program
12 series engines with EMS for all-speed applications
1) Optimized for Clark´s 36000 transmission 2) Optimized for Clark´s 42000 transmissionAll engines comply with Stage 2 EURO exhaust emission regulations.
Ratings IFN: Intermittent service
Descriptions of ratings and other power information, see “General”
Standard equipmentUnit injectors and EMSCoordinatorMain Supply BoxFuel filter cartridgeTurbo chargerAir-to-water charge air cooler (DI engines).Oil cleanerOil filterOil coolerAlternator: 1-pole, 65A, 28 V, incl. relay and connection for tachometer, see “Equipment data”Starter: 1-pole, 6.7 kW, 24 V, see “Equipment data”Flywheel, see “Equipment data”Silumin flywheel housing, SAE1 flange, see “Equipment data”Front mounted engine brackets, see “Equipment data”. Mainly for transportation purposesOperator’s manual
IFN, 2100 r/min
DI12 54A, order ref 10-70 1) kW (hp) 243 (330)
DI12 56A, order ref 10-71 kW (hp) 272 (370)
DI12 56A, order ref 10-72 2) kW (hp) 280 (381)
3Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
Latest modification date: 030401
4 © Scania Industrial & Marine EnginesPart No. 1 588 878
Basic data
GeneralConfiguration and number of cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 in-lineWorking principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 strokeBore x stroke mm . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 x 154Displacement dm3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11,70Compression ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18:1Firing order . . . . . . . . . . . . . . . . . . . . .1 - 5 - 3 - 6 - 2 - 4Piston speed
at 1500 r/min m/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7,70at 1800 r/min m/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9,24
Rotation, seen from flywheel end . . . . . . . . . . . . . . . . . . . . Counter clockwiseMoment of inertia
with flywheel for 14” coupling kgm2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2,74Number of teeths on flywheel ring gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158Weight approx.,
with fan but excl. oil and coolant kg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 995
Lubrication systemOil capacity dm3, min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Oil consumption g/kWh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0,3Oil change intervals h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400Oil grade . . . . . . . . . . . . . . . . . . CE or CF acc. to API
CCMC D5Acea E3-96
Oil PressureNormal bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 6Minimum permitted bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0,7
Oil temperatureMaximum permitted °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Oil cleaner . . . . . . . . . . . . . . . . . Paper and CentrifugalFiltration Micron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7
Oil filter for turbo charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PaperOil cooler . . . . . . . . . . . . . . . . .Water cooled/Full flow
031110
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
031110 © Scania Industrial & Marine Engines
Latest modification date: 030401
Injection systemType . . . . . . . . . . . . . . . Electronic Unit InjectorsGovernor Scania Engine Management System (EMS)Fuel filter . . . . . . . . . . . . . . . . . . . Paper filter element
Cooling systemCoolant volume, excl. radiator dm3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Coolant temperature °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 - 85Number of thermostats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Opening temperature °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Intake systemPermissible pressure drop in intake systemwith cleaned or new filter mmWc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300Permissible pressure drop in intake systemwith blocked (dirty) filter mmWc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500
Electrical system, optional equipmentType . . . . . . . . . . . . . . . . . . . . . 1-pole, 24 V, DC
Optional . . . . . . . . . . . . . . . . . . . . . 2-pole, 24 V, DCStarter, standard equipment . . . . . . . . . . . . . . . . . 1-pole, 24 V - 6.7 kW
Optional . . . . . . . . . . . . . . . . . 2-pole, 24 V - 6.7 kWAlternator, standard equipment . . . . . . . . . . . . . . . . . . . 1-pole, 28 V - 65 A
Optional . . . . . . . . . . . . . . . . . . . 2-pole, 28 V - 65 A. . . . . . . . . . . . . . . . . . . 1-pole, 28 V - 90 A
5Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
Latest modification date: 030401
6 © Scania Industrial & Marine EnginesPart No. 1 588 878
Technical data and cooling equipment recommendation
DI12 54A, order ref. 10-70
Rating acc. to
Engine speed, r/min
1200 1500 1800 2100
Gross power kW (hp) IFN 187 (254) 237 (322) 240 (326) 243 (330)Gross torque Nm (kpm) IFN 1488 (152) 1509 (154) 1273 (130) 1105 (113)Spec. fuel consumption g/kWh (g/hph)
full load 195 (143) 193 (142) 193 (142) 222 (163)3/4 load 199 (146) 199 (146) 194 (143) 229 (168)1/2 load 199 (146) 205 (151) 205 (151) 241 (177)
Heat rejection kWto cooling water 102 129 137 179to exhaust gas 130 165 164 205to surrounding air 21 21 21 24
Air consumption kg/min 14 22 25 30Exhaust flow kg/min 15 23 26 31Exhaust temperature °C 502 437 388 398
IFN, 2100 r/min
Air-on temp.
35 °C 50 °C
Radiatorfront area m2 1.0 1.0weight kg 55 55
Coolant pump flow dm3/min 420 420Fan
type Puller PullerØ mm 787 787power losses kW 21 21number of drive belts (poly-V) 1 1speed ratio 1:1.08 1:1.08
Air flowfree air flow m3/s 9.8 9.8pressure reserve mm Wc 35 30
031110
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
031110 © Scania Industrial & Marine Engines
Latest modification date: 030401
DI12 54A, order ref. 10-70
2200
TORQUENmNm9,81---------- kpm=
200
220
240
280
260
OUTPUTkW
kW x 1.36 = hp
380 hp
360
340
320
300
280
180
1200
1000
120
1401400
1200 1400 1600 1800 2000
SPECIFIC FUELCONSUMPTIONg/kWhg kWh⁄
1,36------------------ g hph⁄=
160 g/hph
210
200150
160 kpm
100
260
240
160
1600
220
r/min
220
190 140
IFN
Max torque1589 Nm/1400 r/min
IFN
IFN
7Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
Latest modification date: 030401
8 © Scania Industrial & Marine EnginesPart No. 1 588 878
Technical data and cooling equipment recommendation
DI12 56A, order ref. 10-71
Rating acc. to
Engine speed, r/min
1200 1500 1800 2100
Gross power kW (hp) IFN 200 (272) 272 (370) 272 (370) 272 (370)Gross torque Nm (kpm) IFN 1592 (162) 1732 (177) 1443 (147) 1237 (126)Spec. fuel consumption g/kWh (g/hph)
full load 197 (145) 190 (140) 192 (141) 214 (157)3/4 load 202 (149) 200 (147) 197 (145) 224 (165)1/2 load 207 (152) 206 (151) 207 (152) 238 (175)
Heat rejection kWto cooling water 109 138 145 180to exhaust gas 143 186 186 222to surrounding air 23 24 23 26
Air consumption kg/min 14 22 27 33Exhaust flow kg/min 15 23 28 34Exhaust temperature °C 549 464 401 393
IFN, 2100 r/min
Air-on temp.
35 °C 50 °C
Radiatorfront area m2 1.0 1.0weight kg 55 55
Coolant pump flow dm3/min 420 420Fan
type Puller PullerØ mm 787 787power losses kW 21 21number of drive belts (poly-V) 1 1speed ratio 1:1.08 1:1.08
Air flowfree air flow m3/s 9.8 9.8pressure reserve mm Wc 35 30
031110
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
031110 © Scania Industrial & Marine Engines
Latest modification date: 030401
DI12 56A, order ref. 10-71
2200
TORQUENmNm9,81---------- kpm=
220
240
260
300
280
OUTPUTkW
kW x 1.36 = hp
400 hp
380
360
340
320
300
200
1400
1200
140
1601600
1200 1400 1600 1800 2000
SPECIFIC FUELCONSUMPTIONg/kWhg kWh⁄
1,36------------------ g hph⁄=
160 g/hph
200
190
150
180 kpm
120
280
260
180
1800
210
r/min
240
180
140
IFN
Max torque1780 Nm/1400 r/min
IFN
IFN
9Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
Latest modification date: 030401
10 © Scania Industrial & Marine EnginesPart No. 1 588 878
Technical data and cooling equipment recommendation
DI12 56A, order ref. 10-72
Rating acc. to
Engine speed, r/min
1200 1500 1800 2100
Gross power kW (hp) IFN 224 (305) 294 (400) 294 (400) 280 (381)Gross torque Nm (kpm) IFN 1783 (182) 1872 (191) 1560 (159) 1273 (130)Spec. fuel consumption g/kWh (g/hph)
full load 200 (147) 193 (142) 196 (144) 217 (160)3/4 load 201 (148) 199 (146) 195 (143) 223 (164)1/2 load 205 (151) 204 (150) 205 (151) 237 (174)
Heat rejection kWto cooling water 127 155 163 198to exhaust gas 160 206 210 240to surrounding air 26 26 26 28
Air consumption kg/min 15 23 28 33Exhaust flow kg/min 16 24 29 34Exhaust temperature °C 567 486 431 425
IFN, 2100 r/min
Air-on temp.
35 °C 50 °C
Radiatorfront area m2 1.0 1.0weight kg 55 55
Coolant pump flow dm3/min 420 420Fan
type Puller PullerØ mm 787 787power losses kW 21 21number of drive belts (poly-V) 1 1speed ratio 1:1.08 1:1.08
Air flowfree air flow m3/s 9.8 9.8pressure reserve mm Wc 25 20
031110
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
031110 © Scania Industrial & Marine Engines
Latest modification date: 030401
DI12 56A, order ref. 10-72
2200
TORQUENmNm9,81---------- kpm=
220
240
260
300
280
OUTPUTkW
kW x 1.36 = hp
400 hp
380
360
340
320
300
200
1400
1200
140
1601600
1200 1400 1600 1800 2000
SPECIFIC FUELCONSUMPTIONg/kWhg kWh⁄
1,36------------------ g hph⁄=
160 g/hph
210
200150
120
280
260
1800
220
r/min190 140
IFN
Max torque1937 Nm/1400 r/min
2000 190 kpm
180
IFN
IFN
11Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
Latest modification date: 030401
12 © Scania Industrial & Marine EnginesPart No. 1 588 878
Basic dimensions
DI12
Function of xyz-coordinates is found in “Equipment data”.*Further information in “Equipment data”.
1. Fuel inlet (Insert connection for plastic pipe Ø 12 mm)*
x ~ -783y ~ -296z ~ +414
2. Fuel return (Insert connection for plastic pipe Ø 12 mm)*
x ~ -325y ~ -296z ~ +103
3. Air intake (Ø 101.6 mm) x -947y +293z +359
4. Exhaust outlet x -702y +293z +359
5. Oil filler* x -1077y -73z +676
6. Oil dipstick*7. Oil drain plug x -634
y -58z -437
8. Connection for engine speed sensor (2x)
9. Coolant inlet (pipe Ø 57 mm) x -1259y +365z +79
10. Coolant outlet (pipe Ø 57 mm) x -1111y +278z +465
11. Drain tap for coolant12. Connection to expansion tank
(pipe Ø 32 mm)x -1177y +287z +337
13. To cab heater inlet14. From cab heater outlet15. Oil pressure sensor16. Connection for coolant temperature
sensor/monitor (2 x M14x1.5)*
1
4
x+ x x-
x- x x+
z-z
z+
y- y y+
7
2
85
13
z-z
z+
3
1116
10
14
9
6
12
15
031110
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
031110 © Scania Industrial & Marine Engines
Latest modification date: 030401
Dimensional drawing
DI12
This sketch is intended only as general sales information and must not be used for any installation purposes. See also “General”
Drawing No. 1 520 626
399
779
396
403
360
379
252
~ 0*
~ 610*
~ 21
0*
* The values for center of gravity applies for engines with standard equipment including coolant.Cooling equipment such as fan, fanring and protective grating are not included.
1434 - 1456 depending on fan type
13Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
Equipment listLatest modification date: 031107
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
10 ENGINE WITH STANDARD EQUIPMENT IFN, kW (hp)Ref Description Drw No.-70 DI12 54A 243 (330) 1 520 626-71 DI12 56A 272 (370) 1 520 626-72 DI12 56A 280 (380) 1 520 626
36 MAIN SUPPLY BOX-02 S Cable harness, length 2 meter 1 505 526-03 O Cable harness, length 8 meter 1 505 526-04 O Cable harness, length 12 meter 1 505 526
37 COORDINATOR-02 S With 1 505 545
41 THROTTLE CONTROL-30 S Without-31 O Accelerator position sensor + cable harness 2 meter 1 364 185-32 O Accelerator position sensor + cable harness 8 meter 1 364 185
45 FLYWHEEL-01 S For use with truck clutch Pilot hole Ø 62 mm 1 402 380 (B)-10 O SAE 14” Pilot hole Ø 80 mm 1 390 317 (B)-11 O For Clark 15/16” Pilot hole Ø 52 mm 1 521 690
46 FLYWHEEL HOUSING-01 S Measurements according to SAE1 Material: Silumin 1 403 464
49 ENGINE SUSPENSION-01 S Front mounting brackets 1 402 865-19 O Fixed suspension, low 1 402 865-21 O Fixed suspension, power pack type 1 402 865-22 O Fixed suspension, power pack type Front brackets only 1 402 865-25 O Stiff rubber suspension, low 1 402 865-26 O Stiff rubber suspension, low Front suspension only 1 402 865-27 O Stiff rubber suspension, power pack type 1 402 865-28 O Stiff rubber suspension, power pack type Front suspension only 1 402 865
14 © Scania Industrial & Marine Engines 031110Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
51 AIR CLEANERRef Description Drw No.-01 S Without-25 O Light duty, with paper insert.
Filter area 10.6 m2For separate mounting 1 399 298
-45 O Medium duty, with paper insert and pre-cleaner. Filter area 16 m2
For separate mounting 1 399 298
51A SAFETY CARTRIDGE FOR AIR CLEANER-00 S Without-01 O Safety cartridge for medium duty air
cleanerOnly for 51-45 1 399 298
55 TURBO CHARGER-02 S Side mounted turbo charger, low 1 403 464-21 O Side mounted turbo charger, high 1 405 277
56 EXHAUST PIPE-00 S Without-11 O Pointing rearwards With exhaust brake, req 55-02 1 424 506-21 O 90° bend Ø 114, adjustable direction. 1 424 507
57 EXHAUST FITTINGS, shipped loose-00 O Without-40 S Flange Ø 89-102, not with 56-21 1 383 334-41 O Flange Ø 114, requires 56-21 1 383 334-42 O Flange Ø 130, requires 56-21 1 383 334-43 O Flange Ø 155, requires 56-21 1 383 334-51 O Flange and compensator Ø 114, requires 56-21 1 383 334-52 O Flange and compensator Ø 130, requires 56-21 1 383 334-53 O Flange and compensator Ø 155, requires 56-21 1 383 334-54 O Compensator for exhaust brake Requires 56-11 1 383 334
58 SILENCER, shipped loose-00 S Without-31 O Truck type with clamps Ø 115 1 331 676-32 O Truck type with flanges Ø 115 1 331 676-33 O Truck type with flanges Ø 130 1 331 676-34 O Truck type with flanges Ø 155 1 331 676-36 O Industrial type, with flanges Ø 130, straight outlet 1 379 683-37 O Industrial type, with flanges Ø 155, straight outlet 1 379 683
031110 © Scania Industrial & Marine Engines 15Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
60 OIL SUMPRef Description Drw No.-05 S Deep front oil sump Oil dipstick on left or right hand side.
Drain plug on low left hand side.1 422 908
-06 O Deep front oil sump Oil dipstick on right hand side. Drain plug on low left hand side. Equipped for checking oil level with running engine.
1 422 908
-07 O Low oil sump Oil dipstick on left or right hand side. 1 422 908
60A OIL DIPSTICK-01 S On right hand side (in oil sump) 1 407 418-02 O On left hand side in engine block. Not with 60-07 1 407 418
61 OIL FILLER-01 S In valve cover 1 403 464-02 O On left hand side (in engine block) Not with 60A-02 or 60-07 1 407 419-03 O In valve cover and on left hand side
(in engine block), 1:st cylNot with 60-07 1 407 419
-03A O In valve cover and on left hand side (in engine block), 5:th cyl
Not with 60-07
62 OIL DRAINING-01 S With magnetic drain plug Under 1 403 464-10 O With hand pump Right hand side (delivered loose) 1 407 848-11 O With hand pump Left hand side (delivered loose) 1 407 848-12 O With hand pump With tap (delivered loose) 1 407 848
66 CRANKSHAFT PULLEY-00 S Standard-14 O With 2 extra grooves Ø 260 mm. For fan ratio 1:1,08 only 1 404 595
-15 O With 2 extra grooves Ø 192 mm. For fan ratio 1:1,08 only 1 404 595
-16 O With 3 extra grooves Ø 260 mm. Without fan only 1 404 595-17 O For poly-V belt Ø 260 mm. For fan ratio 1:1,08 only 1 404 595
16 © Scania Industrial & Marine Engines 031110Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
72 FANRef Description Drw No.-01 S Without fan Without radiator-02 O Prepared for fan Ratio 1:1 Without radiator-03 O Prepared for fan Ratio 1:1,08 Without radiator-07 O Puller Ø 711 mm, ratio 1:1,08 1 385 758-08 O Pusher Ø 711 mm, ratio 1:1,08 1 385 757-09 O Puller Ø 787 mm, ratio 1:1,08. Not with 92A 1 385 760-10 O Pusher Ø 787 mm, ratio 1:1,08. Not with 92A 1 385 759-19 O Puller Ø 787 mm, ratio 1:1. Req alternator 1 385 760-20 O Pusher Ø 787 mm, ratio 1:1. Req alternator 1 385 759
75 RADIATOR AND FAN COVER -00 S Without-21 O 0.75 m2
Not for DC enginesWith fan cover for fan Ø 711 mm 1 407 843
-22 O 0.75 m2 Not for DC engines
With fan cover for fan Ø 711 mm, frame and front grating
1 407 843
-25 O 1.0 m2 With fan cover Not for fan Ø 711 mm
1 407 843
-26 O 1.0 m2 With fan cover, frame and front grating.Not for fan Ø 711mm
1 407 844
-35 O 1.2 m2
Not for DC enginesWith fan cover, Not for fan Ø 711 mm and Ø 787 mm
1 413 544
-36 O 1.2 m2
Not for DC enginesWith fan cover, frame and front grating.Not for fan Ø 711 mm and Ø 787 mm
1 413 545
75A LEVEL MONITOR-00 S Without-13 O Level monitor in expansion tank 1-pole, with 75- only 1 342 316
76 FAN RING-00 S Without-21 O Fan ring with sealing 1 407 485-22 O As 76-21 but with protective grating 1 407 485
80 STARTER-05 O Without-11 S 1-pole 6.7 kW 1 413 727-14 O 2-pole 6.7 kW 1 413 727
031110 © Scania Industrial & Marine Engines 17Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
81 ALTERNATORRef Description Drw No.-03 O Without-20 S 1-pole 65 A 1 404 225-22 O 2-pole 65 A 1 404 225-25 O 1-pole 100 A 1 516 176
82 INSTRUMENT PANEL-01 S With connector kit Req 80-, 81- 1 505 526-40 O Panel, 2-pole 1 505 510-41 O Panel, 2-pole with cupboard 1 505 510 /
1 462 237
89 ENGINE HEATER-00 S Without-11 O 1100W / 220V, plug-in type Approved for use in Sweden, Norway,
Finland, Germany and Austria1 412 624
-23 O 500W / 220V, external Approved for use in Sweden, Norway, Denmark, Finland, Germany, Austria, Switzerland, Iceland, Holland and Belgium
1 407 215-24 O 1500W / 220V, external 1 407 215
90 FRONT MOUNTED POWER TAKE-OFFImportant!
Max. total torque capacity for front end of crankshaft is 1200 Nm.Total torque demands for coupling and drive must never exceed this value.
-00 S Without-20 O Stub shaft for connection of flexible
couplingFor engine without fan onlyNot with 66-15 or -17Max torque 635 Nm
1 404 875
91 SIDE MOUNTED POWER TAKE-OFF-00 S Without-13 O 1,19 x engine speed SAE B, 2-hole, 13 teeth 1 405 720
-13A O Prepared for side mounted PTO Note! see sect.7 1 376 355
92 AIR COMPRESSOR-00 S Without-01 O 2-cylinder, liquid cooled, incl unloader
valveCapacity 380 - 600 l/min at 2100 r/min.Air inlet not connected
1 520 638
92A AC COMPRESSOR-00 S Without-01 O With Not with 72-09, -10 1 404 227
18 © Scania Industrial & Marine Engines 031110Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
93 HYDRAULIC PUMPRef Description Drw No.-00 S Without-12 O Capacity: 16 l/min at 150 bar int., 25-30
bar cont.Without pressure reduction valve 1 404 226
-13 O Capacity: 22 l/min at 150 bar int., 25-30 bar cont.
Without pressure reduction valve 1 404 226
95 PROTECTION COVERS-01 S Standard-04 O With covers for drive belts. with 81- (alternator), Not with 72- 1 432 956-04 O With covers for drive belts. without 81- (alternator), Not with 72- 1 431 749
98B CORRISION PROTECTION-00 S Without-01 O 10 litre corrosion inhibitor. (mix water 90% with inhibitor 10%.)
98C FUEL PRE-FILTER C-00 O Without fuel pre-filter Requires a pre-filter from an external
manufacturer. If no filter is mounted, the engine warranty is not valid.
C-01 S Fuel pre-filter with water separator 1 407 701C-02 O Fuel pre-filter with water separator and
heater1 407 701
98P CONVERTER OIL COOLER-01 S Without-02 O Connection for converter 1 424 243
99 SPECIAL EQUIPMENTA-01 O Tool kitL-31 S Crankcase ventilation Open, direction downwardsL-36 O Crankcase ventilation In valve cover, for external connection 1 405 725L-38 O Crankcase ventilation Internal ventilation 1 405 359N-01 O Scania International ServiceQ-31 O With parts catalogue x1Q-32 O With parts catalogue x2Q-33 O With parts catalogue x3
031110 © Scania Industrial & Marine Engines 19Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
Ideas and opinions about this book?
The ambition with this book is to give you all the information you may need working with Scania engines. However, there can be parts of this book that could be described in another way or some information you wish to be added.
When you have suggestions for improvements, or you find faulty information, please copy this page, write down your opinions and send by telefax or mail to the adress below.
Your remarks may help us to further improve the following editions.
Thank you in advance for your co-operation
Sender:
Suggestion / Remark:
Mail to Scania CV ABIndustrial and Marine EnginesDept. IMSS-151 87 Södertälje, Sweden
Telefax Sales +46 - 8 55 38 29 93 (int)08 55 38 29 93 (nat)
After sales +46 - 8 55 38 98 12(int)08 55 38 98 12(nat)
Telephone +46 - 8 55 38 10 00 (int), 08 55 38 10 00 (nat)
20 © Scania Industrial & Marine Engines 031110Part No. 1 588 878