Scaffolding Works
-
Upload
novy-jamboy-ragmac -
Category
Documents
-
view
222 -
download
0
Transcript of Scaffolding Works
-
7/29/2019 Scaffolding Works
1/17
SCAFFOLDING
BAMBOOSCAFFOLDINGSTANDARDS
-
7/29/2019 Scaffolding Works
2/17
SCAFFOLDING
Thickness
Diameter
> 10mm
> 75mm
Specifications for:
Bamboo Standards & Members
Thickness
Diameter
> 10mm
> 75mm
Bamboo 1
st
Ledgers
Thickness
Diameter
> 10mm
> 40mm
Bamboo Other Ledgers & Braces
1. > 3 years
2. Straight and
3. free from cracks, gnarls,
irregular knots, dry rot, worm-
eaten spots and other defects
external diameter found along
the bamboo member
-
7/29/2019 Scaffolding Works
3/17
SCAFFOLDING
-
7/29/2019 Scaffolding Works
4/17
SCAFFOLDING
nominal width
ultimate strength
5.5~6.0mm
> 50 Kgf
Nylon Strips
for knotting bamboo members
1. All knots should be tightened
with at least 5 rounds of nylonstrips (tight & secure)
2. The ends of the nylon strips
should be crossed and
twisted to form a single
twisted end which passesthrough the knot twice to give
one round turn for proper
anchorage
nominal thickness 0.85~1.0mm
1. any two of members should
be tied up first and then theremaining one should be tied
up on top of them
2. tail of one bamboo member
should be connected to the
head of the other
ledgers/braces/rakers
posts/standards
>2m
1.5~2m
distance between twoknottings on the
overlapping portion of
the bamboo members
-
7/29/2019 Scaffolding Works
5/17
SCAFFOLDING
Overlapping
-
7/29/2019 Scaffolding Works
6/17
SCAFFOLDING
Erecting
bottom level to top level
interior part to exterior part
< 1 storey if on top of a buildingcantilever portion at top should
be properly tied and secured
against wind
Dismantling
top level to bottom level
exterior part to interior part
from non-load parts to load-parts
Scaffolds must be
immediately removed once
the works are completed
-
7/29/2019 Scaffolding Works
7/17
SCAFFOLDING
Guard-rails and toe-boards
When persons are liable to
fall from height
Top guard-rail between 900mm and 1,150mmabove the platform
Intermediateguard-rail
between 450mm and 600mmabove the platform
Otherwise, 2 horizontal bamboo members
spaced at intervals between 750mm to 900mm
Toe-board > 200mmabove the platform
For PKI, toe-boards may not be
installed unless absolutely necessary
-
7/29/2019 Scaffolding Works
8/17
SCAFFOLDING
Working Platform
shall be not less than 400mmin width
Every board or plank
> 200mm in width
> 25mm in thickness
1. straight-grained
2. free from irregular knots,
dry rot, worm holes, cracks & other
defects affecting its strength
OR
> 150mm in width
> 50mm in thickness
Every board or plank
Shall not protrude beyond its end support to more than 150mm
Rest on at least 3 supports to prevent undue or unequal sagging
-
7/29/2019 Scaffolding Works
9/17
SCAFFOLDING
-
7/29/2019 Scaffolding Works
10/17
SCAFFOLDING
Number of Working Platforms
For a scaffold less than 15m in height:
< 2 working platforms for light duty purpose
< 1 working platform for heavy duty purpose
-
7/29/2019 Scaffolding Works
11/17
SCAFFOLDING
Safety Belt
-last resort for fall prevention
-if it is impractical to provide safety net
-attached to a secure anchorage point or an independent lifeline
Bamboo members may be used for anchorage purpose.
-
7/29/2019 Scaffolding Works
12/17
SCAFFOLDING
40mm
Can be used as bracing, other ledger
but not as standard or post
110mm
10mm
Can be used as
standard or post
-
7/29/2019 Scaffolding Works
13/17
SCAFFOLDING
Presence of large cracks
-
7/29/2019 Scaffolding Works
14/17
SCAFFOLDING
1 2 3 4 5 6
At least 5 rounds of nylon
rope
The ends of the rope
should be crossed &
twisted and pass through
the knot twice
Knotting
-
7/29/2019 Scaffolding Works
15/17
SCAFFOLDING
Working platform
510mm
250mm
Width > 400mm
45mm
Platform Member
Width > 200mmThickness > 25mm
-
7/29/2019 Scaffolding Works
16/17
SCAFFOLDING
NO Guard Rail
Guard-rails & toe-boards
should be installed when
there is danger of falling.
-
7/29/2019 Scaffolding Works
17/17
SCAFFOLDING
Pointed ends should not be
allowed for both ledgers &posts