sc-8000 (kelisa)
-
Upload
mohd-shahril -
Category
Documents
-
view
318 -
download
7
Transcript of sc-8000 (kelisa)
( 56392-U )
OWNER’S MANUAL & WARRANTY CARDRADIO & CD PLAYEROWNER’S MANUAL & WARRANTY CARDRADIO & CD PLAYER
INTRODUCTIONThis unit requires an automobile type 12volt negative ground power source. Please read this owner’s guide carefully before you start operating this unit.
CONTENTS
1. FEATURES ............................................ 2
2. GENERAL OPERATION ............................................ 3
3. TUNER OPERATION ............................................ 6
4. PLAYING COMPACT DISCS ............................................ 8
5. CAR CLOCK OPERATION .......................................... 10
6. CARE AND MAINTENANCE .......................................... 11
7. INSTALLATION .......................................... 12
8. RADIO WIRE CONNECTION .......................................... 13
9. CAR CLOCK WIRE CONNECTION .......................................... 14
10. HANDSFREE SYSTEM USER’S GUIDE .......................................... 15
11. AIR CLEANER/OZONIZER USER’S GUIDE .......................................... 22
12. SPECIFICATION .......................................... 24
13. CD TROUBLE SHOOTING GUIDE .......................................... 25
1
2
FEATURES
TUNER AUDIO CONTROL
• Digital PLL Tuning • Electronic Volume/Bass/Treble/Fader and Balance • Manual UP/DOWN Tuning Controls• Seek UP/DOWN Tuning • Power Output (25W x 4) Rms. • 18 FM Preset Memory • Mute• Automatic Store (AS) • Loudness • Preset Signal Scan (PS) • Built-in Noise Canceller (IAC)
GENERAL CD
• Colour LCD Multi-Mode Full information Display • Track UP/DOWN• Digital Quartz Clock • Repeat• Handsfree Mobilephone System • Intro Scan• Air Cleaner/Ozonizer • 24 Programme Memory • Random & Programme Play
GENERAL OPERATION
3
SWITCHING POWER ON (PWR) - 1
Press PWR button 1 to switch on the unit. Press button 1 again to switch off the power.
ADJUSTING AUDIO SELECT BUTTON (SEL) - 2
Press SEL button 2 to change the audio mode through volume, bass, treble, balance and fader function. When
VOL BAS TRE BAL FAD
Each mode appears on the display. When SEL button is pressed.
mode has not been adjusted for 3 seconds, display returns to normal radio or CD display.
FM
PLL SYNTHESIZER RADIO CD PLAYER SEL
6 MEMCLR5
PGM4
RDM3 RPT
A-B2
RPT1
SCNST
A.PS
LDMUTE
RESET
MONOST
CH
DISP
5 6
1 4 2
3
POWER BUTTON
LOUDNESS BUTTON RESET BUTTON
SELECT BUTTON
VOLUME KNOB
MUTEBUTTON
4
MIN NORMAL MAX
VOLUME
BASS
TREBLE
BALANCE
FADER
Turn the Volume Knob clockwise to increase the Volume level. Turn the Volume Knob anti-clockwise to decrease the Volume level.
Turn the Volume Knob clockwise to increase the Bass level. Turn the Volume Knob anti-clockwise to decrease the Bass level.
Turn the Volume Knob clockwise to increase the Treble level. Turn the Volume Knob anti-clockwise to decrease the Treble level.
Turn the Volume Knob clockwise to set the Right Balance. Turn the Volume Knob anti-clockwiseto set the Left Balance.
Turn the Volume Knob clockwise to set the Front speaker sound. Turn the Volume Knob anti-clockwise to set the Rear speaker sound.
Level Control KnobLevel Control Operation
Audio Mode Volume Knob
5
LOUDNESS (LD) - 5
Press the LD button 5 to enhance Bass and Treble at low listening level. “LOUD” will appear on the display when activated. Press again to turn it off.
RESET - 6
In case of abnormal operation or malfunction, use a pencil tip (or other non-metallic object) to press the RESET button 6 . It will return to initial off mode. You are required to turn on power to “activate” the unit.
VOLUME KNOB - 3To adjust the audio level, turn the Volume Knob clockwise to increase the audio level. Turn the Volume Knob anti-clockwise to decrease the audio level.
MUTE (MUTE) - 4
Press MUTE button 4 to decrease the volume to 1/10 of volume level. “MUTE” will appear on the display. Press the same button again to deactivate it.
Precaution! Set the fader control at centre position when using 2-speaker system.
TUNER OPERATION
6
PRESET BUTTON (1 to 6) - 1These buttons are used for preset station function in tuner mode. With this system, a total of 30 stations can be stored in the memory 6 each for the FM I, FM II, FM III and AM I, AM II.
- Preset Station Memory -
With this function, a total 18 stations can be stored in the memory, 6 each for the FM I, FM II and FM III.
1) Tune in the desired station manually or automatically.2) Press the preset button 1 at which you want to store that station for more than 3 second, then the station has been stored in the memory.
3) When your stations are preset at button 1 to 6, you can tune in them simply by pressing the desired button.4) The number of the button appears on the display.
- Preset Buttons and Preset Channel Indicators -
When your favourite stations are preset at buttons 1 to 6, you can tune them in simply by pressing the desired button. The number of the button appears on the display.
BAND BUTTON (FM) - 2This button is used to switch the reception band. The mode switches in order as shown below when “FM” button 2 is pressed.
/BUTTON
2 5 1
3
4A.PS BUTTON
BAND BUTTON STEREO INDICATOR (ST) PRESET BUTTON
FM
PLL SYNTHESIZER RADIO CD PLAYER SEL
6 MEMCLR5 PGM4 RDM3 RPT
A-B2 RPT1 SCNST
A.PS
LDMUTE
RESET
MONOST
CH
DISP
7
FM I FM II FM III MW I MW II
It can switch from CD mode to radio mode without eject the CD from the player.
- Manual Tuning - ( / )
Press the “ ” button 3 sequently in the tuner mode, then the frequency will be increased. Press the “ ” frequency will be decreased. The station frequency is appeared on the display.
- Auto Tuning - ( / )
Press the “ ” 3 button more than 1 second to automatically tune in the next higher receivable frequency, and the “ ” 3 button for a lower frequency. The tuning frequency appears on the display.
PRESET SCAN FUNCTION (A.PS) - 4
Use this function to check the stations stored in the preset memory. When the “A.PS” button 4 is pressed less than 3 seconds, the radio paused for 10 seconds at each station. (When you are not currently listening to a preset station or when you are listening to a preset station, scanning starts from the next station). Either press the “A.PS” button 4 again or press one of the preset buttons 1 to 6 to cancel the scanning operation.
AUTO STORE FUNCTION (A.PS) - 4This function automatically finds six stations with strong signals in the area and stores them in the memory for the (FM I, FM II and FM III) bands, depending on which band has been selected. It comes in handy when travelling far away from home and you do not know the frequency assignments of local stations. Press the “A.PS” button 4 for more than 3 second to automatically store the stations at preset memory channels 1 to 6. If fewer than six stations with strong signal are found, the operations is automatically stopped. Preset Station Scan will immediately follow from preset number 1 as soon as the auto is completed.
MONO (ST) - 5Press “ST” button 5 to select stereo or monaural (mono reception for radio station). You can sometimes improve reception of distant station by selecting mono operation.
PLAYING COMPACT DISCS
8
LISTENING TO THE CD PLAYER
1) With the label side up, insert a disc into disc slot 1 . Playback will start. Track number will be displayed. * Do not insert the disc with the label side down. Doing so may scratch the disc. * If the disc stops midway while it is being inserted or if there is no playback after a disc is inserted, something may be wrong with the disc. Eject the disc and check it.
2) Adjust volume and level control. (see page 4)
3) Press FM button 2 to interrupt disc-play and transfer to radio operation. Press “ ” button 3 again to resume disc-play at the begining of the last track played.
4) Eject the disc by pressing EJECT button 4 . * Do not leave the disc halfway into the unit. Doing so may cause the disc to be bent or dropped.
PLAY/PAUSE ( ) - 3
Press “ ” button 3 to pause play temporarily and press once again to resume play.
TRACK SELECT ( / ) - 5
- Press “ ” button 5 to forward to the next track.- Press “ ” button 5 to backward to the previous track.
Track number will appear on the display.
5
27
8 9 13 12 113
1 46
DISC SLOT10DISPLAYBUTTON
/BUTTON
BAND BUTTON
SCANBUTTON
REPEATBUTTON
REPEAT A-BBUTTON
RANDOMBUTTON
PROGRAMMEBUTTON
MEMORY CLEARBUTTON
CD SLOT INDICATIONWITH GREEN LIGHT LED
EJECTBUTTON
BUTTON
FM
PLL SYNTHESIZER RADIO CD PLAYER SEL
6 MEMCLR5
PGM4
RDM3 RPT
A-B2
RPT1
SCNST
A.PS
LDMUTE
RESET
MONOST
CH
DISP
9
CD SLOT INDICATION - 6This is use to indicate the insertion CD location. It is indicated with green light. CD is inserted on the left hand side of the green light.
INTRO SCAN (SCN) - 7Intro Scan function allows you to scan a disc, by playing the first 10 seconds of each track in order. Press SCN button 7 to activate intro scan. Once you hear the desired track, press again to resume its normal playback.
REPEAT (RPT) - 8
To repeat the music you are listening to, press RPT button 8 . RPT will appear on the display and current track will be repeated continuously. Press again to cancel the repeat mode.
REPEATING BETWEEN A AND B (RPT A-B) - 9
This function allows you to repeat a section between A and B in the disc, which you want to listen repeatedly. Press RPT A-B button 9 when start your desired sec-tion. “RPT-A” with running time will appear on the display. Press again when finish your desired section. “RPT-B” will appear on the display. The section A-B will be repeated continuously, until press the same button again.
DISPLAY (DISP) - 10
To display the running time & the remaining time for a track. Press the DISP button 10 to show the running time and press again to show the remaining time. Again, press to resume to normal mode.
MEMORY, PROGRAMME
This function lets you programme the play of selected tracks. Up to 24 selections can be programmed as following order.1) Select a desired track by pressing “ / ” button 5 buttons.2) Press MEM CLR button 11 to store up the track.3) Repeat steps 1 and 2 to memory additional tracks.4) Once programming is completed, press PGM button 12 to begin playback as programmed in sequence. At this time, “PGM” indicator and programmed track number will appear on the display.5) To stop programme play, press PGM button 12 again.6) To clear all the programme memory, press MEM CLR button 11 when playing in the programme play mode.
RANDOM - 13
This allows the unit to select a song randomly from CD. Press RDM button 13 to activate this function and “RDM” will appears on the LCD. Press again to deactivate this function.
10
CAR CLOCK OPERATION
SETTING THE CAR CLOCK
Press the “M” button to adjust minute. Press the “H” button to adjust hour. To preset the clock, press the “SET” button. The minute preset has divided to two parts which is 29 minutes past every hour and 30 minutes to every hour. For examples, if the time is 8.29 o’clock, depress the “SET” button for more than two seconds, the time will become 8.00 o’clock automatically. If the time is 8.30 o’clock, depress the “SET” button, the time will become 9.00 o’clock automatically.
H M SET
CAR CLOCK FRONT VIEW
11
CARE AND MAINTENANCE
DISCS
* Only use compact discs (optical digital discs) bearing the mark. (Figure 1)* Do not use cracked, scratched or warped discs.* Do not touch the disc’s playing side. Handle the disc as shown (Figure 2).* Do not affix any label on the disc.* Do not apply any vinyl record spray, antistatic agent, benzene, paint thinner or any other volatile chemicals.* Do not play a dirty disc. Use a soft cloth to clean a dirty disc as shown (Figure 3). Wipe the disc outward from the centre.* Do not place the disc in high temperatures and direct sunlight. (Figure 4)* Be sure to store the disc in its case.
CD PLAYING ENVIRONMENT
* Disc playback may be interrupted by sudden road shock.* When the air temperature is low and the car heater is turned on, condensation on the disc and internal parts of the unit may prevent proper playback operation. If this happened, turn off the unit and wait one hour until the condensation is gone. Also, use a soft cloth to wipe off any condensation from the disc.
(Figure 1)
(Figure 2)
(Figure 3)
(Figure 4)
INSTALLATION
1. Remove the instrument cluster panel from car dashboard.2. Install the radio set to the dashboard case provided and screw up with 5 x 13 TP (black).3. Replace the instrument cluster panel to the car dashboard.
12INSTRUMENT CLUSTER PANEL
CAR STEERINGCAR DASHBOARD
INSTALLATION BRACKETCLOCK ASSEMBLY
RADIO UNIT
H M SET
SCREW 4 ( 5 x 13 TP ) BLACK
FM
PLL SYNTHESIZER
RADIO
CD
PLAYER
SEL
6 MEMCLR
5
PGM4
RDM3 RPT
A-B2
RPT
1
SCNST
A.PS
LDMUTE
RESET
MONOST
CH
DISP
RADIO WIRE CONNECTION
13
Antenna Jack
2p BLACK
4p W
HIT
E
2p W
HIT
E
ADAPTOR
HANDPHONE WIRE BOX
EAR PHONE WIRE BOX
NOKIA
C
Orange
Red
Black
FRONT
REAR
ACC (12V)
To Car batt 12V
GroundRightLeft
+ Brown
- Brown/Yellow
+ Gray
- Gray/Yellow
+ Green
- Green/White
+ Blue
- Blue/White
Fuse 10A
Fuse 3A
CAR CLOCK WIRE CONNECTION
14
LIG
HTI
NG
+
GR
OU
ND
-
BAT
T+
AC
C +
RED, ACC (+)
BROWN, LIGHTING (+)
ORANGE, TO CAR BATT 12V (+)
BLACK, TO CAR BODY (-)
++
++
CAR CLOCK REAR VIEW
HANDSFREE INTEGRATED WITH AUDIO SYSTEM
SAFETY CAUTION:* IN ORDER TO ENSURE SAFETY, USER ARE STRICTLY ADVISE TO STOP THE CAR BY THE ROAD SIDE BEFORE MAKING ANY CALL.
PENGGABUNGAN ALAT BEBAS TANGAN DENGAN SISTEM AUDIO
AMARAN KESELAMATAN:* DEMI KESELAMATAN, PENGGUNA ADALAH DINASIHATKAN SUPAYA MENGHENTIKAN KERETA DI TEPI JALANRAYA SEMASA MEMBUAT SEBARANG PANGGILAN. 15
16
HOW TO USE THE HANDPHONE MAGNETIC HOLDER
1. Locate a suitable surface at the rear side of the handphone.2. Ensure the surface is free of oil, grease and dirt.3. Remove the protective film from the self adhesive metal plate and attach the metal plate to that surface. (Figure 1)4. Be sure the metal plate adheres firmly to the handphone.5. Place the handphone to the magnetic holder and ensure the metal plate adheres correctly to the holder by magnetic force.6. To remove the handphone from the magnetic holder, hold the handphone and press the release lever at the side of the magnetic holder and withdraw the handphone. (Figure 2)
PRECAUTION: Hold the handphone before pressing the release lever
Clean Surface
Remove protective film
Self-adhesivemetal plate
Attach
Rear Side of Handphone
Release Lever
(Figure 1) (Figure 2)
NOKIA
C
NOK IA
17
BAGAIMANA MENGGUNAKAN “MAGNETIC HOLDER” TELEFON BIMBIT
1. Pilih satu permukaan yang sesuai dibahagian belakang telefon bimbit.2. Pastikan permukaan itu bebas dari minyak, gris dan kotoran.3. Tanggalkan lapisan perlindungan dari plat logam berpelekat dan lekat pada bahagian permukaan tersebut. (Rajah 1)4. Pastikan plat logam melekat kuat pada telefon bimbit.5. Letak telefon bimbit ke “magnetic holder” dan pastikan plat logam melekat betul pada “holder” dengan tarikan magnet.6. Untuk menanggalkan telefon bimbit dari “magnetic holder”, pegang telefon bimbit dan tekan “release lever” disisi “magnetic holder” dan keluarkan telefon bimbit. (Rajah 2)
PERHATIAN : Pegang telefon bimbit sebelum
menekan ‘release lever’.
Plat logam berpelekat
Tanggalkan lapisan perlindungan
Permukaan bersih
Bahagian belakang telefon bimbit
Lekat
Release Lever
(Rajah 1) (Rajah 2)
NOKIA
NOKIA
C
18
HANDSFREE INTEGRATED WITH AUDIO SYSTEMCAUTION1. -a) Ensure the proper adaptor is being correctly hook up with your handphone. -b) Always connect the adaptor first before hook-up to your handphone. -c) Failure to follow the above sequence, (Figure 1) may cause your handphone system does not function properly. 2. Advisable volume tone on your handphone is at 70% level. The higher the volume level, the higher the possibility of causing double sided echo occurring.3. The volume level of incoming signal are control by the handphone only.4. Please set the handphone to the auto-answering mode, if it is available. The auto-answering will activate when any message is coming in. If the auto-answering mode is not available or user choose not to use this mode, you are required to press ‘receive’ key to start the conversation.5. The magnetic holder must stuck on firmly to the dashboard. (Figure 2) Before that, ensure the dashboard is clean and dry.
DIALING/ANSWERING A CALLWhile dialing or answering a call, audio output will be cut-off automatically. The receiving conversation can be heard from front-left speaker.
ENDING A CALLThe audio output will resume in about 10 seconds after ending a call.
EAR PHONE OPTION (only applicable with audio system power ‘on’)In order to have private conversation, press the mute button on earphone (Figure 3), the received conversation will switch from front-left speaker to earphone.
RETRACTABLE EARPHONE AND HANDPHONE (Figure 4)The maximum retractable length of Earphone and Handphone is at 1.1m. Failure to follow above instruction would cause the system does not function properly.
NOTES: The circuitry of Audio phone design is base on hand-phone model Nokia- 3210, 3310, 8210, 8250 and 8850. The usage of other type hand-phone may deviate the origin performance of the system. (Motorola V-Series can be con nected directly witout usage of adaptor.)
Figure 1
Figure 2
Figure 4
Figure 3
Step 1 Step 2 Step 3
Metal Plate
Car DashboardMagnetic Holder
Handphone Retractable
WireEarphone
Mute Button
NOK IA
C
NOK IA
C
NOK IA
C
19
NOKIANOKIA
NOKIA
C
F M
PLL SYNTHESIZER RADIO CD PLAYER
S E L
6 ME MC L R
5 P G M4 R DM
3 R P TA-B
2 R P T1 S C N
S T
A.P S
L DMUT E
RESET
MONOS T
C H
DIS P
HANDSFREE WIRE CONNECTION AND INSTALLATION
CAR DASHBOARD
MICROPHONEHANDPHONE
HANDPHONE HOLDER
SELF ADHESIVE METAL PLATE
PHONE WIRE BOX
MAGNETIC HOLDER
CAR STEERING
EAR PHONE
WIRE BOX (AUTO RETRACTABLE)
COIN COMPARTMENT
NOKIA
C
PH
ON
E W
IRE
BO
X
RADIO SET
CLOCK
4p BLACK
2p BLACK
2p BLACKMIC
4p W
HIT
E
2p W
HIT
E
ADAPTOR
EAR PHONE WIRE BOX
20
PENGGABUNGAN TELEFON BIMBIT DENGAN SISTEM AUDIOPERHATIAN1. -a) Pastikan adaptor sentiasa disambungkan dahulu dengan betul sebelum memasangnya pada telefon bimbit. -b) Sistem telefon bimbit tidak dapat berfungsi dengan betul sekiranya wayar dan adaptor tidak disambung dengan sempurna. (Rajah 1)2. Kekuatan kawalan bunyi pada telefon bimbit dinasihatkan pada kadar 70%. Semakin kuat kawalan bunyi dilaraskan, semakin kuatlah gema akan kedengaran.3. Kekuatan kawalan bunyi masuk hanya boleh dilaraskan dengan menggunakan telefon bimbit.4. Sila set telefon bimbit anda kepada mod “auto-answering”. Mod ini akan aktif apabila mesej diterima. Sekiranya tiada kemudahan ini atau pengguna memilih tidak menggunakan kemudahan ini, anda dikehendaki tekan butang “terima” untuk panggilan masuk.5. Tapak pemegang bermagnet mestilah dilekatkan kukuh di papan hempasan kereta. (Rajah 2) Sebelum itu, pastikan papan hempasan bersih dan kering.
PANGGILAN KELUAR/MASUKSemasa panggilan keluar/masuk berlaku, sistem output audio akan berhenti secara automatik. Anda akan dapat mendengar perbualan melalui pembesar suara di sebelah kiri bahagian hadapan.
PANGGILAN TAMATSetelah panggilan tamat, output audio mengambil masa 10 saat untuk memasang semula siaran radio.
PILIHAN (Hanya berfungsi semasa sistem audio ‘on’)Untuk perbualan peribadi, sila tekan butang “mute” di “earphone” (Rajah 3).
WAYAR BERGULUNG PADA EARPHONE DAN TELEFON BIMBIT (Rajah 4)Jarak maksimum yang boleh ditarik keluar daripada kotak wayar “Earphone” dan kotak wayar “Telefon” adalah 1.1 meter. Sebarang penggunaan yang melebihi jarak tersebut akan menjejaskan fungsi sistem ini.
NOTA: Penggabungan telefon bimbit dengan sistem audio ini direkabentuk berasaskan model Nokia-3210, 3310, 8210, 8250 dan 8850. Pengguna telefon bimbit yang lain mungkin akan menjejaskan spesifikasi asal sistem ini. (Motorola V-Series boleh disambungkan secara terus tanpa penggunaan adaptor.)
Rajah 1
Rajah 2
Rajah 4
Rajah 3
Plat Logam
Papan HempasanTapak Pemegang
Bermagnet
Butang Mute
EarphoneWayar
BergulungTelefonBimbit
NOK IA
C
NOK IA
C
NOK IA
C
21
PEMASANGAN DAN WAYAR SAMBUNGAN
EAR PHONEWIRE BOX (AUTO RETRACTABLE)KOTAK WAYAR “EAR PHONE”
COIN COMPARTMENTPENGISI DUIT SILING
CAR DASHBOARDPAPAN HEMPASAN
CAR STEERINGSTERING KERETA
MICROPHONEPEMBESAR SUARA
HANDPHONETELEFON BIMBIT HANDPHONE HOLDER
PEMEGANG TELEFON BIMBIT
MAGNETIC HOLDERTAPAK BERMAGNET
SELF ADHESIVE METAL PLATEPLAT LOGAM BERPELEKAT
PHONE WIRE BOXKOTAK WAYAR TELEFON
NOKIANOKIA
NOKIA
C
F M
PLL
SYNTHESIZER
RADIO
CD
PLAYER
S E L
6 ME MC L R
5
P G M4
R DM3 R P T
A-B
2
R P T1
S C NS T
A.P S
L DMUT E
RESET
MONOS T
C H
DIS P
NOKIA
C
PH
ON
E W
IRE
BO
X
RADIO SET
CLOCK
4p BLACK
2p BLACK
2p BLACKMIC
4p W
HIT
E
2p W
HIT
E
ADAPTOR
EAR PHONE WIRE BOX
22
1. ‘POWER’ - 1 : This power button is to manually switch ‘off’ and ‘on’ the unit when Acc is being on.
2. ‘ON’ LED - 2 : The ‘ON’ LED is light up when the unit is in operation. (‘STANDBY’ LED also will light up)
3. ‘STANDBY’ LED - 3 : Whenever the unit is being switch ‘off’ by power - 1 button, the unit will not in operation with only ‘STANDBY’ LED light up.
AC-2100 Air Cleaner User’s Guide
GENERAL OPERATIONAt initial stage the ozonizer being installed to the vehicle.
Whenever the ACC being turn - on, the unit will remain ‘OFF’. Users are required to manually switch ‘ON’ the power button of the unit in order to ‘ON’ the unit.
Whenever last condition is at power ‘ON’, re-on the ACC, unit will go to ‘ON’ mode.
Whenever last condition is at power ‘OFF’, re-on the ACC, unit will go to ‘OFF’ mode.
In overall, the unit will always maintain at last condition mode either ‘ON’ or ‘OFF’ whenever the ACC being on.
21
3
AIR CLEANER/OZONIZER CAN EFFECTIVELY ELIMINATE THE POLLUTANTS1. Stink in the car.2. Smoke.3. Bacteria and mold.4. Chemical gases.5. Odors.
CAUTION1. Ozone (03) is 1.7 times weighted than the air. Please place the unit at higher position for better efficiency.2. The unit is high frequency designed. Please do not clean or wipe it while using.3. Do not wash the unit.4. Do not insert anything in it’s outlet to wind which will cause damage.5. Please stop using ozonizer temporarily if you have a feeling of discomfort or if you are much stimulated or feel dizzy.6. When the car is fully filled with ozone, wind down the window for ventilation.
SPECIFICATIONType : AC-2100 Air CleanerDimensions : 129(L) x 140(W) x 64(H)mmWeight : 327.5 gram Output level of ozone (03) : 0.02ppm/8 hoursVoltage : DC 12VPower Consumption : 1.3W
23
24
SPECIFICATION
GENERAL
Power Supply Voltage : DC 12.0VRate : 14.4VDimensions : 182(W)x54.2(H)x171.5(D)mmWeight : Approximately 1.6KgsMute : Output 1/10 of volume levelCurrent Consumption : Less than 10ASpeaker Impedence : 4 to 8 ohmsGrounding System : Negative Type
FM TUNER
Frequency Range : 87.5 - 108MHzUsable Sensitivity : 10dB-3dB Limiting Sensitivity : 10dBSignal To Noise Ratio : 50dBStereo Separation : 30dB
CD PLAYER
System : Compact disc audio system Frequnecy Characteristics : 10 - 10,000Hz (±3dB)Signal To Noise Ratio : 70dBDynamic Range : 80dB
POWER AMPLIFIER
Maximum Power Output : 25W x 4Rms.Tone Controls (Bass) : ± 10dB (@100Hz)(Treble) : ± 10dB (@10KHz)Loudness Control : ± 10dB (100Hz)
CAR CLOCK
Operating Voltage : DC 14.4V (10.8V-16V allowable)Current Comsuption : 120mABack-up Current : 0.3mA
CD TROUBLE SHOOTING GUIDE
DISPLAY CAUSE TREATMENT
E-1
E-2, 3
E-4, 8, 7
E-6
E-7, 8
E-A
E-B
E-C
E-D
Eject the disc and re-insert when normal temperature
Eject the disc and re-insert
Insert the disc with the label side up or clean the pick-up lens with CD cleaner disc
Eject the disc and re-insert
Clean the disc or Replace the disc
Disc eject and re-insert
High temperature
Loading, Eject
The disc inserted with label side down or pick-up lens dirty
Electrical or mechanical fault
The disc dirty or scratched
Febias adjust
Focus offset adjust
Tracking balance
Tracking gain adjust
25
BETAMEK ELECTRONICS (M) SDN. BHD. IALAH SYARIKAT YANG MENJAMIN KELUARAN INI, TER-TAKLUK KEPADA SYARAT-SYARAT BERIKUT:1. SEKIRANYA DALAM KEADAAN KEGUNAAN BIASA
TERBUKTI KELUARAN INI ROSAK SENDIRI ATAU RO-SAK DARI SEGI PEMBUATANNYA DALAM TEMPOH 24 BULAN ATAU 50,000KM BERGANTUNG PADA YANG MANA BERLAKU DAHULU DARI TARIKH BELIAN, MAKA KEROSAKAN ITU AKAN DIPERBAIKI TANPA APA-APA BAYARAN.
2. PERKHIDMATAN JAMINAN AKAN HANYA DIBERI SETELAH PIHAK PEMBELI MENYERAHKAN KAD JAMINAN YANG SAH DAN YANG DICAP/DITANDATANGAN OLEH PIHAK/PIHAK-PIHAK YANG DIBERI KUASA.
3. JAMINAN INI TIDAK MELIPUTI PENGHAPUSAN STATIK KERETA, KEBISINGAN KENDERAAN, PEMBETULAN KEPADA MASALAH ANTENA, KOS YANG TERLIBAT UN-TUK MENANGGALKAN ATAU MEMASANG KELUARAN INI ATAU KEROSAKAN PITA, AKSESORI DAN LAIN-LAIN.
4. JAMINAN INI TIDAK MELIPUTI APA-APA KEROSAKAN YANG DISEBABKAN OLEH SALAH GUNA, SALAH LAKU, KECUAIAN, KEMALANGAN ATAU PEMBAIKAN/PEN-GUBAHSUAIAN YANG DILAKUKAN OLEH PIHAK YANG TIDAK DIBERI KUASA UNTUK BERBUAT DEMIKIAN.
5. JAMINAN INI TERBATAL SEKIRANYA NOMBOR SIRI DI BAHAGIAN ATAS RADIO TERTANGGAL DARIPADA UNIT INI ATAU LABEL JAMINAN DI BAHAGIAN BELAKANG
RADIO KOYAK.
BETAMEK ELECTRONICS (M) SDN. BHD, THE COMPANY GUARANTEED THIS PRODUCT WHICH SUBJECT TO THE FOLLOWING TERMS AND CONDITIONS:1. SHOULD THIS PRODUCT THEREOF UNDER NORMAL
USE AND CONDITIONS; BE PROVEN DEFECTIVE IN MATERIAL OR WORKMANSHIP WITHIN 24 MONTHS OR 50,000KM WHICHEVER COMES FIRST FROM THE DATE OF ORIGINAL PURCHASE, SUCH DEFECT (S) WILL BE REPAIRED WITHOUT ANY CHARGES.
2. WARRANTY SERVICE WILL BE ONLY DONE UPON PRESENTATION OF A VALID WARRANTY CARD DULY
STAMPED/SIGNED BY AUTHORISED PARTY/PARTIES.3. THIS WARRANTY DOES NOT EXTEND TO THE ELIMINATION OF CAR STATIC OR MOTOR NOISE, TO
CORRECTION OF ANTENNA PROBLEMS TO COSTS INCURRED FOR REMOVAL OR REINSTALLATION OF
THE PRODUCT, OR DAMAGE TO TAPES, ACCESSORIES ETC.
4. THIS WARRANTY DOES NOT COVER ANY DAMAGES CAUSED BY MISUSE, MISHANDLING, NEGLIGENCE OR ACCIDENT OR REPAIR/ALTERNATION BY UNAUTHO-RISED PARTY.
5. THIS WARRANTY SHALL BE VOID IF THE SERIAL NUMBER AT THE TOP COVER OF THE RADIO IS REMOVED FROM THE UNIT OR THE WARRANTY LABEL AT THE BACK OF THE RADIO IS TORN.
PERODUA SALES SDN BHD (66332U)(Wholly owned subsidiary of Perusahaan Otomobil Kedua Sdn Bhd)
Perodua Automotive Centre, Sungai Choh, Locked Bag No. 226,48009 Rawang, Selangor Darul Ehsan, Malaysia.Tel. No.: 03-6092 8888. Fax No.: 03-6091 5698
RC L701-08011ST Edition