Sawtooth Generator
-
Upload
oliver-twiste -
Category
Documents
-
view
225 -
download
3
Transcript of Sawtooth Generator
-
7/27/2019 Sawtooth Generator
1/23
Block 5
Wave shaping Circuits
-
7/27/2019 Sawtooth Generator
2/23
3c. Identify Sawtooth Generator Operating
Principles
-
7/27/2019 Sawtooth Generator
3/23
SAWTOOTH
PURPOSE To produce a sawtoothwaveform. One input cycle will produce
one output cycle.Also known as sweep, time/base,time/division, seconds/division, or ramp
generator.
This circuit is considered a relaxation
oscillator.
-
7/27/2019 Sawtooth Generator
4/23
Parts of sawtooth waveform
Sweep time/electrical length
(Time allowed to charge)
Rest or flyback time (Discharge Time)
Physical length (Amplitude)
Slope (Rate of rise/percent of curve) PRT
PRF
-
7/27/2019 Sawtooth Generator
5/23
-
7/27/2019 Sawtooth Generator
6/23
The Sawtooth Generator, produces a waveform that
will have a linear rise characteristic. RISE over RUN
SLOPE
2 2
2
1
1
-
7/27/2019 Sawtooth Generator
7/23
Simple Sawtooth Circuit
-
7/27/2019 Sawtooth Generator
8/23
100
90
80
70
60
50
40
30
20
10
0.5 1 2 3 4 5
CURVE RC CIRCUIT LR CIRCUIT
A
B
CAPACITOR VOLT AGEON CHARGE
INDUCTOR CURRENTOR RESISTOR VOLTAGEON BUILD-UP
CAPACITOR VOLT AGEON DISCHARGE
INDUCTOR CURRENTOR RESISTOR VOLTAGEON DECAY
RESISTOR VOLTAGEOR CAPACITOR CUR-RENT ON CHARGE ORDISCHARGE
INDUCTOR VOLTAGE ONBUILD-UP OR DECAY
A
B
0.5 1 2 3 4 5
AQR30020010-9307-999
TIME IN THE TIME CONSTANTS
Universal Time Constant Chart
Referring to theUniversal Time
Constant Chart,you will find thatthe most linearpart of the curve
is the first 10%of the first timeconstant.
-
7/27/2019 Sawtooth Generator
9/23
Sawtooth Generator
-
7/27/2019 Sawtooth Generator
10/23
Purpose of Components
R1 Provides forward bias for Q1.
C1
Input signal coupling capacitorQ1 Serves as charge and discharge
switch for the RC network consisting of
R2 and C2.
R2/C2 RC network that produces the
slope/ramp portion of the output wave.
-
7/27/2019 Sawtooth Generator
11/23
Sawtooth Generator Operation
C2 charges through R2 developingthe output slope when Q1 is cutoffby the negative gate.
+1.2V
-
7/27/2019 Sawtooth Generator
12/23
Sawtooth Generator Operation
C2 discharges through Q1 when Q1issaturated (conducting) by thepositive gate and this is the flyback
time.+1.2V
-
7/27/2019 Sawtooth Generator
13/23
Relationships
RC
teLengthNegativeGa
Amplitude
teLengthNegativeGaRCLinearity
-
7/27/2019 Sawtooth Generator
14/23
Gate Length Linearity
Relationship
TIME
GATE
INCREASE IN
GATE LENGTH
AMPLITUDE
A. INCREASING GATE LENGTH
TIME
GATE
DECREASE IN
GATE LENGTH
AMPLITUDE
B. DECREASING GATE LENGTH
-
7/27/2019 Sawtooth Generator
15/23
RC
Linearity Relationship
INCREASINGR OR C
AMPLITUDE
TIME TIME
GATE
A. INCREASING R or C
DECREASINGR OR C
AMPLITUDE
GATE
B. DECREASING R or C
AQR2E020010-9704-1119
Increases Linearity Decreases Linearity
Before After
-
7/27/2019 Sawtooth Generator
16/23
Block 5
Summary 3c
Parts of the Waveform
Sawtooth Generator components
Circuit operation
Parameter Changes
-
7/27/2019 Sawtooth Generator
17/23
Sawtooth Generator
Appraisal
-
7/27/2019 Sawtooth Generator
18/23
Sawtooth Generator
1. In the sawtooth generator circuit, a positive gateapplied to the base of Q1 will ________ C2.
a. chargeb. discharge
-
7/27/2019 Sawtooth Generator
19/23
Sawtooth Generator
2. In the sawtooth generator circuit, the rate of voltagechange across capacitor C2 is almost linear
during the first ____ of the capacitor charge time.a. 1%
b. 5%
c. 10%
d. 20%
-
7/27/2019 Sawtooth Generator
20/23
Sawtooth Generator
3. The linearity of the sawtooth waveform is controlledby
a. R2b. C2
c. negative input gate duration
d. all of the above
-
7/27/2019 Sawtooth Generator
21/23
Sawtooth Generator
4. A negative gate applied to the base of Q1 will_____ Q1 and allow C2 to ______ through R2.
a. cutoff; chargeb. cutoff; discharge
c. saturate; charge
d. saturate; discharge
-
7/27/2019 Sawtooth Generator
22/23
Appraisal Answers
1. B
2. C
3. D4. A
-
7/27/2019 Sawtooth Generator
23/23
The End