THANK YOU FOR CHOOSING KϋRYAKYN! PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND PROPERTY DAM-AGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAU-TIONS, AND NOTICES REGARDING THE INSTALLATION, USE, AND CARE OF THIS PRODUCT.

MAKE SURE THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT: 1 Satin Black Right Transmission Cover 1 Satin Black Left Transmission Cover 1 Hardware Kit containing: 1 Transmission Cover Bracket 2 Cable Ties 3 M5 X 0.8 X 10MM Button Socket Head Cap Screws 1 Installation instructions TOOLS SUGGESTED: Set of metric hex wrenches, long socket extension, set of metric hex bit sockets, in lbs (Nm) torque wrench

STEP 1 Read and understand all steps in the instructions before starting the installation.

Park the motorcycle on a hard, level surface and turn IGN OFF. Allow the engine and exhaust system to cool.

INSTALLATION

CUSTOMER SERVICE 877.370.3604 (toll free)

INSTALLATION QUESTIONS

techsupport@kuryakyn.com or call 715.247.2983

LIMITED WARRANTY

Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of defects in

materials and workmanship for a period of one (1) year from the date of purchase by the

consumer excepting the following provisions:

● Küryakyn shall have no obligation in the event the customer is unable to provide a receipt

showing the date the customer purchased the product(s).

●The product must be properly installed,

maintained and operated under normal conditions.

●Küryakyn makes no warranty, expressed or

implied, with respect to any gold plated products.

●Küryakyn shall not be liable for any

consequential and incidental damages, including labor and paint, resulting from failure of a

Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or

for any breech of contract or duty between Küryakyn and a customer.

●Küryakyn products are often intended for use in

specific applications. Küryakyn makes no warranty if a Küryakyn product is used in

applications other than intended.

●Küryakyn electrical products are warranted for one (1) year from the date of purchase by the

consumer. L.E.D.’S contained in components of Küryakyn products will be warranted for defects in materials and workmanship for 3 years from

the date of purchase where as all other components shall be warranted for one(1) year.

This includes, but is not limited to; control modules, wiring, chrome & other components.

●Küryakyn makes no warranty of any kind in

regard to other manufacturer¹s products distributed by Küryakyn. Küryakyn will pass on

all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but ultimately, responsibility for disposition of the warranty claim lies

with the manufacturer.

ABOUT OUR CATALOG For purchasing Küryakyn® products, you

can receive a complete catalog free of charge. Send the Proof-of-Purchase below with your

address to: Küryakyn 454 County Road V V

Somerset, WI 54025-9031 Please indicate either Accessories Catalog for

Harley-Davidson® or GL & Metric Cruisers.

Be sure to ask your local dealer about other Küryakyn® products, the motorcycle parts and

accessories designed for riders by riders.

©2005 Küryakyn USA® All Rights reserved.

SATIN BLACK REAR TRANSMISSION CENTER COVER — VICTORY

7623-22MC-1214 -cont.-

THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.

This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality or damage the product itself or the product to which it is being attached.

This indication alerts you to the fact that ignoring the contents described herein can result in minor or moderate potential injury.

7623

These installation instructions contain important information. Ensure that the end user receives this copy and is aware of its importance for future reference.

Working around the sharp edges of the cylinder-head fins exposes your hands to injury. Wear protective gloves to prevent serious injury.

YOU WILL BE WORKING AROUND THE ENGINE AND EXHAUST SYSTEM DURING INSTALLATION. ENSURE THAT THE ENGINE AND EXHAUST SYSTEM HAVE FULLY COOLED TO PREVENT INJURY.

PAGE

2

SATIN BLACK REAR TRANSMISSION CENTER COVER — VICTORY

-cont.-

INSTALLATION

STEP 2 Refer to PIC 1. On the clutch-side (left) of the engine case, locate the OEM clutch-cable-bracket.

STEP 3 Refer to PIC 2. From the brake-side (right) of the bike, locate the upper clutch-cable-bracket screw (M6); remove the upper screw and set it aside for now, it will be reused.

STEP 4 Refer to PIC 3. Locate the included Transmission Cover

Bracket in the kit. Position the Bracket against the cable bracket; align the holes and loosely secure the Bracket with the M6 screw from STEP 3. Leave the screw loose for now to allow for adjustment.

STEP 5 Refer to PIC 4. Secure the breather hose to the clutch

cable housing with an included Cable Tie. Do not over tighten the Cable Tie to allow for adjustment of the hose. Ensure that the hose does not get pulled out of the rubber crankcase fitting.

STEP 6 Refer to PIC 5. Locate the Left Transmission Cover in the kit.

Secure the Cover to the Bracket using two of the included screws; begin both screws in their threads before finish-tightening them.

NOTE: Ensure that the breather hose is centered in

the Left Cover cut-out to prevent damage from abrasion. Adjust the rubber crankcase fitting if necessary; compress the tabs on the clamp, then rotate the fitting. Ensure that the hose will not get pinched, rub exces-sively, or get pulled out of the fitting.

STEP 7 Press down on the front of the Cover

and finish-tighten the M6 screw under-neath.

FRONT OF BIKE

VIEW OF THE CLUTCH-SIDE (LEFT) ENGINE CASE PIC 1

OEM CLUTCH CABLE BRACKET

REMOVE THE UPPER CLUTCH-CABLE -BRACKET SCREW (M6)

FRONT OF BIKE

VIEWED FROM BRAKE-SIDE (RIGHT)

PIC 2

SECURE THE TRANSMISSION COVER BRACKET WITH THE EXISTING SCREW

PIC 3 VIEW FROM CLUTCH-SIDE (LEFT)

FRONT OF BIKE

PIC 5 VIEW FROM CLUTCH-SIDE (LEFT)

SECURE THE COVER TO THE BRACKET

SECURE BREATHER HOSE TO CLUTCH CABLE WITH CABLE TIE

PIC 4 VIEW FROM CLUTCH-SIDE (LEFT)

PAGE

3

STEP 8 On the brake-side (right) of the bike, remove the M6 screw from the drive belt cover as shown in PIC 6; set the screw aside, it will be reused later.

NOTE: Ensure that the metal spacer and rub-ber bushing remain in the drive belt cover.

STEP 7 Refer to PIC 7. Locate the Right Transmission Cover in

the kit. STEP 8 Refer to PIC 8. Attach the Right Transmission Cover to

the drive belt cover with the M6 screw removed in STEP 8; leave the screw snug for now to allow for adjustment.

STEP 11 Refer to PIC 8. Press down on the rear of the Right

Transmission Cover and torque the M6 screw to 85 in lbs (9.5 Nm).

STEP 12 Refer to PIC 6 and 8. Ensure that the seams are still

aligned; tighten the center screw. If necessary, loosen the screws, adjust the covers, then retighten the screws.

SATIN BLACK REAR TRANSMISSION CENTER COVER — VICTORY

Ride On! INSTALLATION

It is the end user’s responsibility to ensure that all of the fasteners (including pre-assembled) are tightened before operation of the motorcy-cle. Küryakyn will not provide warranty coverage on products or compo-nents lost due to improper installation or lack of maintenance. Periodic in-spection and maintenance are required on all fasteners.

PIC 6 PIC 6 BRAKE-SIDE (RIGHT)

REMOVE THE M6 SCREW

PIC 7 PARTS SHOWN ASSEMBLED OFF OF THE BIKE FOR CLARITY

BRAKE-SIDE (RIGHT) COVER

CLUTCH-SIDE (LEFT) COVER

ALIGN SEAMS

M6 SCREW

CENTER SCREW

TIPS FOR PROPER CARE: Your new SATIN BLACK product requires special attention when

cleaning. Some cleaning products or procedures can actually damage the product.

Thoroughly clean the product often with a soft cloth, mild soap

and water. Regular cleaning keeps contaminates from building up.

Rinse thoroughly with FRESH water. Use only cleaning products that are formulated for SATIN BLACK

paint. DO NOT USE products containing abrasives to clean the SATIN

BLACK product. Never use steel or brass wool, wire brushes, polishing wheels, rubbing or polishing compounds on the prod-uct.

PIC 7 PIC 8 BRAKE-SIDE (RIGHT)

SECURE THE COVERS WITH THE REMAINING BUTTON HEAD SCREW

PRESS DOWN ON THE REAR OF THE RIGHT COVER AND TIGHTEN THE M6 SCREW