SAN_Host_Storage_commands v2.0.pdf
9
[email protected] :: MDS-SERIES (CISCO) COMMANDS :: http://www.cisco.com/en/US/products/ps5989/prod_command_reference_list.html MDS-SERIES Switch Commands ip address 191.168.123.234 255.255.255.0 View = ~ show running-config show environment ~ shows status of all installed hardware components show flogi database ~ shows database list of all FLOGI events show fcns database ~ shows database list of all N-ports logged in show vsan membership ~ shows list of VSAN members show interface brief ~ lists the interfaces and status MDS-SERIES Zoning Commands config terminal ~Enters configuration terminal fcalias ~creates an alias for a member zone name TestZone1 vsan 4 ~ creates a zone member pwwn 10:01:10:01:10:ab:cd:ef ~ adds node to the zone above no member pwwn <colon separated wwn> ~deletes member from zone zoneset name Zoneset1 vsan 4 ~ creates a zoneset member <zone name> ~adds zone to the ZoneSet above no zone name <zone name> vsan <vsan Id> ~ Deletes a zone zoneset activate name Zoneset1 vsan 4 zone copy active-zoneset full-Zoneset1 vsan 4 copy running-config start-up config ~ copy from source to startup configuration vsan database ~ go into vsan configuration mode vsan 4 interface fc3/21 ~move port 21 on module 3 to vsan 4 show zoneset ~ shows all zonesets that are active show zone vsan <#> ~ shows all zones active in vsan show zoneset active ~ displays the active zoneset show vsan ~ shows the vsans on the switch show zoneset active vsan <vsan Id> ~ Shows active zoneset :: B-SERIES (BROCADE) COMMANDS :: http://powerlink.emc.com/km/appmanager/km/secureDesktop?internalId=0b01406680024e88 B-SERIES Switch Commands ipAddrSet ~set the IP address of a Brocade switch switchShow ~ display switch info supportShow ~ full detailed switch info portShow # ~ display port info nsShow ~ Name server contents nsAllShow ~ NS for full fabric fabricShow ~ fabric information ad --create ~create a new Admin Domain. B-SERIES Zoning Commands aliCreate “Alias”, “20:00:00:e0:69:40:07:08” zoneCreate “Zone1”, “20:00:00:e0:69:40:07:08; 50:06:04:82:b8:90:c1:8d” cfgCreate “Test_cfg”, “Zone1; Zone2” cfgSave ~ saves zoning information across reboots cfgEnable “Test_cfg” ~enable a zoneset config, zoneShow or cfgShow ~ shows defined and effective zones and configurations zoneAdd ~ adds a member to a zone zoneRemove ~ removes a member from a zone zoneDelete ~ deletes a zone cfgAdd ~ adds a zone to a zone configuration cfgRemove ~ removes a zone from a zone configuration cfgDelete ~ deletes a zone from a zone configuration
description
SAN Switch Commands for Host Storage
Transcript of SAN_Host_Storage_commands v2.0.pdf
:: MDS-SERIES (CISCO) COMMANDS :: http://www.cisco.com/en/US/products/ps5989/prod_command_reference_list.html
MDS-SERIES Switch Commands ip address 191.168.123.234 255.255.255.0 View = ~ show running-config show environment ~ shows status of all installed hardware components show flogi database ~ shows database list of all FLOGI events show fcns database ~ shows database list of all N-ports logged in show vsan membership ~ shows list of VSAN members show interface brief ~ lists the interfaces and status
MDS-SERIES Zoning Commands config terminal ~Enters configuration terminal fcalias ~creates an alias for a member zone name TestZone1 vsan 4 ~ creates a zone member pwwn 10:01:10:01:10:ab:cd:ef ~ adds node to the zone above no member pwwn <colon separated wwn> ~deletes member from zone zoneset name Zoneset1 vsan 4 ~ creates a zoneset member <zone name> ~adds zone to the ZoneSet above no zone name <zone name> vsan <vsan Id> ~ Deletes a zone zoneset activate name Zoneset1 vsan 4 zone copy active-zoneset full-Zoneset1 vsan 4 copy running-config start-up config ~ copy from source to startup configuration vsan database ~ go into vsan configuration mode vsan 4 interface fc3/21 ~move port 21 on module 3 to vsan 4 show zoneset ~ shows all zonesets that are active show zone vsan <#> ~ shows all zones active in vsan show zoneset active ~ displays the active zoneset show vsan ~ shows the vsans on the switch show zoneset active vsan <vsan Id> ~ Shows active zoneset
:: B-SERIES (BROCADE) COMMANDS :: http://powerlink.emc.com/km/appmanager/km/secureDesktop?internalId=0b01406680024e88
B-SERIES Switch Commands ipAddrSet ~set the IP address of a Brocade switch switchShow ~ display switch info supportShow ~ full detailed switch info portShow # ~ display port info nsShow ~ Name server contents nsAllShow ~ NS for full fabric fabricShow ~ fabric information ad --create ~create a new Admin Domain.
B-SERIES Zoning Commands aliCreate “Alias”, “20:00:00:e0:69:40:07:08” zoneCreate “Zone1”, “20:00:00:e0:69:40:07:08; 50:06:04:82:b8:90:c1:8d” cfgCreate “Test_cfg”, “Zone1; Zone2” cfgSave ~ saves zoning information across reboots cfgEnable “Test_cfg” ~enable a zoneset config, zoneShow or cfgShow ~ shows defined and effective zones and configurations zoneAdd ~ adds a member to a zone zoneRemove ~ removes a member from a zone zoneDelete ~ deletes a zone cfgAdd ~ adds a zone to a zone configuration cfgRemove ~ removes a zone from a zone configuration cfgDelete ~ deletes a zone from a zone configuration
::Veritas VM HOST COMMANDS :: http://www.symantec.com/business/support/documentation.jsp?language=english&view=manuals&pid=15273
Veritas VM Device Commands vxdisk list ~ List all disks under volume manager control and give there status. vxdiskadd c1t2d3 ~ add or bring a disk under volume manager control vxdiskadmin ~ Interactive front end to the vxdisk program
Veritas VM Filesystem commands vxdisk init ~ Initialize Physical Volume vxdg init mydg mydg-01=c1t11d0 ~ Create Disk Group vxassist -g mydg make myvol <size> ~ Create Logical Volume mkfs -F vxfs /dev/vx/rdsk/mydg/myvol ~ create file system vxvol -g mydg stopall ~ stop a volume vxdg deport mydg ~ deport disk group vxdg import mydg ~ import disk group vxvol -g mydg startall ~ starting a imported volume
::VMware ESX HOST COMMANDS :: http://www.vmware.com/support/developer/vcli/
VMware ESX Device Commands esxcfg-info Print out device configurations esxcfg-module -l List modules loaded in the service console vmkfstools (-P, -q, -g) ~RDM Target LUN information esxcfg-advcfg esxcfg-resgrp esxcfg-auth ~A uthentication configuration VMware ESX Storage commands esxcfg-info –s ~General Storage Info vdf -h ~Disk Space Utilization fdisk /dev/sdX ~ esxcfg-scsidevs -A ~prints a mapping between the HBA and the devices esxcfg-nas -a ~Adds a new NAS file system to the ESX/ESXi host. esxcfg-boot Manage the boot partitions esxcfg-dumppart -l Manage the vmkdump partition esxcfg-mpath –l ~Path information esxcfg-vmhbadevs –m ~VMKernel-to-Service Console Device Mapping esxcfg-rescan <vmkernel adpter> ~scan for new disks esxcfg-swiscsi –e ~enable iSCSI initiator esxcfg-rescan ~Rescan LUNs on SCSI device esxcfg-resgrp ~Create, delete and list resource groups vmkpcidivy –q vmhba_devs ~map canonical name to Vmware file system
VMware ESX Networking commands esxcfg-firewall esxcfg-nics ~Presents physical NIC information esxcfg-route ~Enable or disable routing for vmknics esxcfg-swscsi ~Configures software iSCSIadapters esxcfg-vmhbadevs ~Maps COS device files to vmhbanames esxcfg-vmknic ~Create & configure VMkernel NICs esxcfg-vswif ~Create & configure vswifsfor the COS esxcfg-vswitch ~Create & configure virtual switches andport groups
:: Windows HOST COMMANDS :: http://support.microsoft.com/default.aspx/ph/3198?sid=26
Windows 2003 server SP1 Device Commands SystemInfo ~ Displays detailed configuration information about a computer and its operating system Shutdown /r /f ~ forced reboot Netstat ~ Displays active TCP connections, ports on which the computer is listening mstsc /v: 255.255.255.255 /console ~ launches a Remote desktop Connection net use \\ComputerName\ShareName\volume ~ Connects a computer to a computer shared resource FC ~ compares two files and displays the differences ChkDsk ~ check and repair disk problems Recover ~ Recover a damaged file from a defective disk. fcinfo /details ~ if fcinfo is installed ,this will list the HBA’s wwns
Windows 2003 server SP1 LVM Commands Diskpart rescan ~ Locates new disks that may have been added to the computer Diskpart list disk ~ Displays a list of disks and information about them, Diskpart detail disk ~ Displays the properties of the selected disk and the volumes on that disk.
wmic partition get BlockSize, StartingOffset, Name, Index ~find the starting offset Diskpart create partition primary align=64 ~create a properly offset partition MountVol ~ Creates, deletes, or lists a volume mount point. Diskpart assign ~ Assigns a drive letter or mount point to the volume with focus. Diskpart extend ~ Extends the volume with focus into next contiguous unallocated space Diskpart import ~ Imports a foreign disk group into the local computer's disk group Format /FS:filesystem ~ Specifies the type of the file system (FAT, FAT32, or NTFS). FSutil volume dismount
:: VI COMMANDS :: Cursor movements h ~ left one character l ~ right one character j ~ down one line k ~ up one line w ~ right one word b ~ back one word
Deleting, Yanking, and Pasting d ~ delete x ~ delete character cursor is on r ~ replace one character y ~ yank (copy into temporary buffer) Y ~ yank line cursor is on p ~ paste below cursor line (deleted or copied text)
Saving and Exiting u ~ undo last editing command ZZ ~ save and exit (hold down shift and press "z" twice) :wq! ~ write and quit even if it is read-only
:: FTP COMMANDS :: open <IP address> ~ undo last editing command close <IP address> ~ save and exit (hold down shift and press "z" twice) bin ~set to transfer for binary and text files hash ~display progress during get mget ~mutiple get – download files in to current directory mput ~multiple pu – upload files from current directory
:: AIX/IBM HOST COMMANDS :: http://publib.boulder.ibm.com/infocenter/pseries/v5r3/index.jsp?topic
AIX Software Installation /usr/lpp ~ Software Directory lslpp -L all ~ List installed software lslpp -f fileset ~ List all files instfix –i ~ List installed patches cp *.lpp /usr/sys/inst.images ~ copy lpp software to the install directory smit installp ~ Install a software package rmdev ~ Remove a device
AIX Device Commands lscfg ~ lists all comfigured components smit or smitty ~ system management utility lscfg –v l <interface> ~ lists all attributes (WWN’s) for a device emc_cfgmgr ~ configures symmetrix devices mkbcv ~ makes BCV visable to AIX to avoid locking during boot (1) chdev -l fcsX -a init_link=pt2pt –P ~ “To change INIT Link flags parameter” (2) chdev -l fscsiX -a fc_err_recov=fast_fail –P ~ “Fabric Event Error RECOVERY Policy” (3) cfgmgr –v ~ cofigures devices and optionally installs device software
AIX NFS Commands exportfs ~Lists all exported filesystems exportfs -a ~Exports all fs's in /etc/exports file exportfs -u (filesystem) ~Un-exports a filesystem mknfs ~Configures and starts NFS services rmnfs ~Stops and un-configures NFS services mknfsexp -d /directory ~Creates an NFS export directory mknfsmnt ~Creates an NFS mount directory mount hostname:/filesystem /mount-point ~Mount an NFS filesystem nfso -a ~Display NFS Options
AIX iSCSI Commands
smit iscsi
AIX Filesystem Commands http://the-welters.com/professional/aix/jfs-lvm.html lsdev –Cc disk ~ Device Listing and status mkdev ~ configures a disk device masking sue it is available as a physical volume chdev -l hdisk# -a pv=yes ~ Initialize Physical Volume lspv -l hdisk# ~ Disk Label mkvg -y myvg -s 16 hdisk2 ~ groups one or more physical devices into a volume group
mirrorvg ~Creates mirror volumes for all volumes in a volume group. extendvg myvg hdisk3 hdisk4 ~ Extend Volume Goup lsvg – l vgname ~ displays volumes, with a specified volume group mklv -y mylv myvg 16 ~ Make logical volume mklvcopy hd1 2 hdisk1 ~(2) makes a copy of lv should be followed up by syncvg command lslv ~ List Logical Volume
chfs -a freeze ~writes all dirty file system metadata and user data to the disk (use before BC & DR) crfs –v jfs –d mylv –m /myfs mount ~ mounts a filesystem varyoffvg myvg ~ Deactivate Volume Group exportvg myvg ~ Export Volume Group importvg -y myvg -f /dev/hdisk9 ~ Import Volume Group varyonvg myvg ~ Activate Volume Group
:: HP/UX HOST COMMANDS :: http://www.docs.hp.com/en/B2355-90681/index.html
HP/UX Software Installation sysdef ~ analyzes current running system swlist –l bundle ~ displays version and type of HP-UX swlist -l patch ~ List installed patches swreg –l depot /full/path/to/your/depot_file ~ Register a depot package for install swinstall ~ Install the Software depot
HP/UX Device Commands insf –e ~ install special device files ioscan -fnC disk ~ scans system hardware sam ~ System administration tool dd if=/dev/rdsk/c34t15d0 of=/dev/zero count=1 ~ makes HP register with a Clariion thru LUNZ device navicli –h <SP IP> register ~registers host with Clariion and tests agent install lsdev –C disk ~ list device drivers in the system mknod ~ makes a directory, special, or ordinary file /stand/system ~ system configuration file
HP SAN Commands fcmsutil /dev/fcd0 ~ List HBA wwn tdutil /dev/td0 ~ List HBA wwn
HP iSCSI Commands
http://docs.hp.com/en/T1452-90011/T1452-90011.pdf
HP NFS Commands /etc/exports ~file controls which file systems are exported to remote hosts and specify options /exported/directory example.emc.com ~Exports directory to host example.emc.com (found in /etc/exports) exportfs –a ~command to read /etc/export and export filesystem mount shadowman.emc.com:/misc/export /misc/local ~mount an NFS export from shadowman.emc.com to the dir /misc/local
HP/UX Filesystem commands pvcreate /dev/rdsk/c1t0d2 ~ creates a physical volume within a LVM volume group pvdisplay ~ display info about physical volumes within an LVM volume group ls -l /dev/*/group ~list the minor number of each vg in 6
th field (all not listed are available)
mkdir /dev/myvg ~Create directory entry in /dev for Volume Group mknod /dev/myvg/group c 64 0x010000 ~ Create a file for Volume Group vgcreate -s 16 /dev/myvg /dev/dsk/c1t0d0 ~ creates a LVM volume group vgextend /dev/myvg /dev/dsk/c1t0d1 ~ add disk to VG vgchange -a y myvg ~ Avtivate VG vgscan ~ scan physical volumes for LVM volume groups vgdisplay ~ displays info about LVM volume groups lvcreate -l 16 -n mylv /dev/myvg ~ creates LVM logical volumes lvcreate -m mylv /dev/myvg ~ creates mirrored logical volumes lvdisplay ~ displays LVM logical volumes newfs /dev/myvg/rmylv ~ Create file system mount /dev/myvg/mylv /myfs ~ Mount file system vgchange -a n myvg ~ Deactivate Volume Group vgexport myvg ~ Export Volume Group vgimport /dev/myvg /dev/dsk/c1t0d0 ~ Import Volume Group
:: Linux HOST COMMANDS :: http://www.redhat.com/docs/manuals/enterprise/RHEL-5-manual/en-US/
Linux Software Installation rpm –hiv
Linux Device Commands modeinfo lpfc | grep parm ~Emulex hba parameters modprobe -r lpfc ~unload Emulex driver lsmod | grep lpfc ~ modprobe lpfc ~ discover new disk /sys/class/scsi_host/host1/issue_lip ~ discover new disk dmesg |grep scsi ~list scsi devices /sys/class/scsi_host/host1/scan ~ discover new disk /usr/sbin/lpfc lun_scan all
Linux FC SAN Commands hbacmd list ~list Emulex hba hbacmd allnodeinfo xx:xx:xx:xx:xx:xx:xx:xx ~detail hba wwn info & device list more /sys/class/scsi_host/hostX/port_name ~ wwn on RHEL4 more /sys/class/fc_host/hostX/port_name ~ wwn on RHEL5
Linux iSCSI Commands yum install iscsi-initiator-utils ~install iSCSI soft initiator rpm -q srvadmin-deng iscsi-initiator-utils ~install iSCSI soft initiator rpm -ql iscsi-initiator-utils ~confiure iSCSI soft initiator iscsi-iname ~discover iqn iscsi-ls ~list adapters iscsiadm -m discovery -t -p 192.168.1.100 ~discover iSCSI target iscsiadm --mode node --targetname iqn ~
Linux NFS Commands
/etc/exports ~file controls which file systems are exported to remote hosts and specify options /exported/directory example.emc.com ~Exports directory to host example.emc.com (found in /etc/exports) exportfs –a ~command to read /etc/export and export filesystem mount shadowman.example.com:/misc/export /misc/local ~mount an NFS export redhat-config-nfs ~RedHat NFS tool
Linux Filesystem commands http://linux.about.com/od/commands/l/blcmdl_8m.htm pvcreate /dev/emcpowerX ~ initializes PhysicalVolume for later use by the Logical Volume Manager vgcreate VG_Name /dev/emcpowerX ~ creates a new volume group lvcreate --size 2000m --name LV_Name /dev/VG_Name ~creates 2000MB logical volume mkfs -t ext2 /dev/VG_Name/LV_Name ~ Make a file system on a logical volume mount -t ext2 /dev/VG_Name/LV_Name /mnt/FS_MountPoint ~ mount File system df –a ~display filesystems Fdisk /dev/sda ~ partition table manipulation pvdisplay ~ allows you to see the attributes of one or more physical volumes pvscan ~ scans all supported LVM block devices in the system for physical volumes vgdisplay ~display attributes of volume groups vgextend ~ allows you to add one or more initialized physical volumes vgscan ~ scan physical volumes for LVM volume groups
vgexport ~make volume groups unknown to the system
vgimport ~make volume groups known to the system lvdisplay ~display attributes of a logical volume lvextend ~ Extend logigal volume fsck ~Command used to check and repair a Linux filesystem
:: SUN/SOLARIS HOST COMMANDS :: http://developers.sun.com/openstorage/articles/opensolaris_storage_server.html
SOLARIS Software Installation ptree –a ~ Shows all running processes in a tree format showrev –p ~ Displays currently installed Solaris patches prtconf ~ prints system configurations pkginfo ~ lists installed software packages pkgadd ~ install software packages pkgrm ~ removes installed software packages
Solaris Device Commands cfgadm –a ~ list all cfgadm –c configure c4 ~ configure StorEdge Leadville driver.(Search for new devices) devfsadm –vC ~ searches for devices and also cleans up old update_drv -f sd -d –I ~ searches for devices drvconfig ~ generates special device files reboot -- -r ~ reboots system to discover configuration changes, and rebuild special files /etc/system ~ system files /kernel/drv/sd.conf ~ lists of available target ids and luns /kernel/drc/lpfc.conf ~ used for persistent binding on Emulex (qla22xx.conf for Qlogic) /var/adm/messages ~ system messages Solaris iSCSI Commands iscsiadm add static-config iqn.1999-08.com.array:sn.01234567,192.168.1.3:3260 ~map target iscsiadm add discovery-address 192.168.1.13:3260 iscsiadm modify discovery --isns enable iscsiadm list target –vS Target: iqn.1986-03.com devfsadm -Cv -i iscsi Solaris FC SAN Commands fcinfo hba-port ~ Lists information and WWNs fcinfo remote-port -p 10000000c937694f –ls ~ Lists the remote-port information fcadm create-fcoe-port -t nxge0 ~Creates a FCoE target port
Solaris NFS Commands share -F nfs -d "Cartman dir" / share2 mount -F nfs cartman:/share2 /cartman share -F nfs -o ro=sun.ucs.indiana.edu,rw=teak.uwsg.indiana.edu /reports ~ export (share) /reports /etc/dfs/dfstab ~ file to edit to make a share permanent shareall –F nfs ~ command to excute that will read /etc/dfs/dfstab and share to the network
SOLARIS Filesystem Commands *** Format and lable all devices before using zpool ***
zpool create spoon c3t6d9 ~create & mounts storage pool named spoon and mounts it at /spoon (no slice #)
zpool create spoon mirror emcpower3c emcpower4c ~create a RAID1 storage pool mounted at /spoon
zpool destroy –f spoon ~destroy a zpool
zfs create spoon/fs ~creates ZFS file system spoon/fs, automatically mounted at /spoon/fs.
zpool list ~list pools
format ~ Disk partit ioning and maintenance program
sysdef ~ Device Listing
prtvtoc ~ Disk Label
metadevadm ~ Checks device ID configuration.
metainit ~ Configures volumes.
metastat ~ Displays the status of volumes or hot spare pools.
metaset ~ Admin isters disk sets.
newfs –v ~ makes a UFS filesystem on disk drive or partition within a diskdrive
zfs snapshot pool/filesystem@Thursday ~Take a read-only snapshot of a file system
zfs ro llback pool/filesystem@Thursday ~Rollback live filesystem to snapshot
:: SOLUTIONS ENABLER COMMANDS :: http://powerlink.emc.com/km/appmanager/km/secureDesktop?internalId=0b014066800250af
Commands to see devices syminq ~ list all devides seen by host OS syminq -cids ~ list Clariion devices syminq hba –fibre ~ list HBA syminq –pdevfile ~List the location of devices sympd list ~ lists the Symmetrix devices that the host OS can see symdev list pd ~ lists the Symmetrix devices that the host OS can see symdisk
Symdev Commands symdev list ~ list all devices on symm symdev –sa –p list ~ list devices maped to that one FA symdev list –noport ~ list devices not mapped to any FE ports symdev list –clariion symdev show 0123 -v ~ vebose listing of one device
Symcfg Commands symcfg discover ~ discover the storage environment symcfg list ~ list local and remote symmetrixes symcfg list –FA all list ~ lists all fibre directors in a Symmetrix system symcfg list -dir all -address -available ~ sid 6196 ~ returns the next available LUN address symcfg list -lockn all ~ list of visible Symm exclusive locks symcfg -sid <sid> -lockn 15 release ~ release a lock on a Symmetrix array.
Symconfigure Commands symconfigure –sid <sid> -f <filename> preview ~ checks file to make sure it is ok to exe symconfigure –sid <sid> -f <filename> commit ~ makes the changes from file symconfigure –sid <sid> -f <filename> prepare
Symmaskdb Commands symmaskdb list devs ~ lists all devices accessible to an HBA on a specified Symmetrix system symmaskdb remove ~ removes the meta member devices symmaskdb backup ~ backs up a database to a specified file symmaskdb init ~ deletes and creates a new VCMDB symmaskdb list assignment ~lists deives already assigned symmaskdb list no_assignment ~lists deives not yet assigned
Symaccess Commands symaccess -sid <sid> -file <BackupFileName> backup ~ symaccess list hba -v ~ symaccess -sid <sid> list assignment -v ~ symaccess -sid <sid> list logins ~ symaccess create -name <GroupName> -type initiator -wwn <wwn> ~ symaccess create -name <GroupName> -type port -dirport <Dir>:<Port> ~ symaccess create -name <GroupName> -type storage devs <SymDevStart:SymDevEnd> ~ symaccess create view -name <GroupsAndViewName> -wwn ~
Symmask Commands symmask add devs ~ adds a device to the list of devices that a WWN can access in the database symmask remove devs ~ removes a device from the list of devices that a WWN can access in the database symmask refresh ~ refresh vcmdb to all FA ports symmask login ~ lists for each Fibre director which hosts and HBA’s are logged in to a Symmetrix system symmask list HBA’s ~ lists the WWN of the Fibre HBAs on this host symmask -sid <sid> -wwn 50060B000024F9F6 -dir 16C -p 1 set heterogeneous on HP_UX
Other SYMCLI Commands symsan ~list ports and LUN WWNs seen from a specific Symmetrix director and port symdg ~ creates/deletes/renames device groups symld ~ addes & removes devices to a deivce group symbcv ~ associates/disassociate BCV with device groups symmir ~ performs (split/establish/restore) BCV mirror commands against device groups symclone ~ performs (split/establish/restore/activate/terminate/recreate) symsnap ~ performs (restore/activate/terminate/recreate) symrdf ~ performs (split/establish/restore/failover/update/failback/suspend/resume) against RDF device groups symcg ~ Performs operations on a Symmetrix RDF composite group symrslv ~ Displays logical-to-physical mapping information about a logical object that is stored on a disk. symstat ~ Displays statistics information about a Symmetrix, any or all directors, a device group, a disk, or a device. symioctl ~ sends I/O control commands to application
:: NAVICLI COMMANDS :: http://powerlink.emc.com/km/appmanager/km/secureDesktop?internalId=0b01406680025003
naviseccli –h <SP IP> getsp ~ verify connectivity naviseccli –h <SP IP> register ~registers host with Clariion and tests agent install naviseccli –h <SP IP> storagegroup ~ list all info about existing groups naviseccli –h <SP IP> getrg -lunlist ~ list all existing raid groups and LUNS naviseccli –h <SP IP> getdisk ~ shows numbers of disks in storage array naviseccli –h <SP IP> getrg <rg id> ~ shows the number of raid groups naviseccli –h <SP IP> get lun <lun id> ~ lists all the disks naviseccli –h <SP IP> storagegroup -list ~ displays storage groups naviseccli –h <SP IP> getcache ~ shows the cache naviseccli –h <SP IP> port –list –sp ~list all the SP port’s wwpn naviseccli –h <SP IP> createrg ~create a raid group naviseccli –h <SP IP> bind –rg –cap –aa ~bind a lun naviseccli –h <SP IP> storagegroup –create –gname <name> ~ creates a new storage group naviseccli –h <SP IP> storagegroup –addhlu –gname <name> -hlu <#> -alu <#> ~ assigns LUNs to storage group naviseccli –h <SP IP> storagegroup –connecthost –host <hname> -gname <gname> ~ assigns host to storage group
:: POWERPATH COMMANDS ::
http://powerlink.emc.com/km/appmanager/km/secureDesktop?internalId=0b01406680025034 powermt ~ manage powerpath environment powercf ~ configure powerpath devices powermt display dev=all ~display PowerPath controlled devices powermt check powermt config emcpreg ~ manage powerpath license registration emcpupgrade ~ convert powerpath configuration files
:: INQ ::
ftp://ftp.lss.emc.com/pub/symm3000/inquiry/ Inq –h ~ list options and syntax Inq –hba ~ list hba wwn Inq –btl ~ display Bus Target and Lun Inq –showvol ~ display Symmetrix Volume Number. Inq –winvol ~ show Windows filesystems Inq -clariion ~ display CLARiiON device information inq -dev \\.\physicaldrive1 -page0 ~ Raw unformatted data on a single device inq -dev \\.\physicaldrive21 -pagec0 ~Raw formatted info on a Clariion volume
