Samsung An15vs Samtron 56v 56e Samsung 551v s

COLOR MONITORChassis ModelAN15V* 551V, 551S

56V, 56E

ManualSERVICECOLOR MONITOR CONTENTS

1. Precautions

2. Product Specifications

3. Disassembly & Reassembly

4. Alignment & Adjustments

5. Troubleshooting

6. Exploded View & Parts List

7. Electrical Parts List

8. Block Diagram

9. Wiring Diagram

10. Schematic Diagrams

CONFIDENTIAL

WARNINGS1. For continued safety, do not attempt to modify the

circuit board.

2. Disconnect the AC power before servicing.

3. When the chassis is operating, semiconductorheatsinks are potential shock hazards.

1-1-1 Servicing the High Voltage and CRT :WARNING:A high voltage adjusted to the wrong

value may cause excessive X-ray

emissions.

1. When servicing the high voltage system, removethe static charge by connecting a 10 kohm resistorin series with an insulated wire (such as a testprobe) between the chassis and the anode lead.

2. When troubleshooting a monitor with excessivelyHV, avoid being unnecessarily close to the monitor.Do not operate the monitor for longer than isnecessary to locate the cause of excessive voltage.

3. High voltage should always be kept at the ratedvalue, no higher. Only when high voltage isexcessive are X-rays capable of penetrating the shellof the CRT, including the lead in glass material.Operation at high voltages may also cause failure ofthe CRT or high voltage circuitry.

4. When the HV regulator is operating properly, thereis no possibility of an X-ray problem. Make sure theHV does not exceed its specified value and that it isregulating correctly.

5. The CRT is especially designed to prohibit X-ray emissions. To ensure continued X-rayprotection, replace the CRT only with one that isthe same or equivalent type as the original.

6. Handle the CRT only when wearing shatterproofgoggles and after completely discharging the highvoltage anode.

7. Do not lift the CRT by the neck.

1-1-2 Fire and Shock Hazard :Before returning the monitor to the user, perform thefollowing safety checks:

1. Inspect each lead dress to make certain that theleads are not pinched or that hardware is notlodged between the chassis and other metal parts inthe monitor.

2. Inspect all protective devices such as nonmetalliccontrol knobs, insulating materials, cabinet backs,adjustment and compartment covers or shields,isolation resistor-capacitor networks, mechanicalinsulators, etc.

3. Leakage Current Hot Check (Figure 1-1): WARNING: Do not use an isolation transformer during

this test.Use a leakage current tester or a metering systemthat complies with American National StandardsInstitute (ANSI C101.1, Leakage Current forAppliances), and Underwriters Laboratories (ULPublication UL1410, 59.7).

4. With the unit completely reassembled, plug the ACline cord directly into a 120V AC outlet. With theunit’s AC switch first in the ON position and thenOFF, measure the current between a known earthground (metal water pipe, conduit, etc.) and allexposed metal parts, including: metal cabinets,screwheads and control shafts. The currentmeasured should not exceed 0.5 milliamp. Reversethe power-plug prongs in the AC outlet and repeatthe test.

Figure 1-1. Leakage Current Test Circuit

1-1-3 Product Safety NoticesSome electrical and mechanical parts have specialsafety-related characteristics which are often notevident from visual inspection. The protection they givemay not be obtained by replacing them withcomponents rated for higher voltage, wattage, etc. Partsthat have special safety characteristics are identified by

on schematics and parts lists. A substitutereplacement that does not have the same safetycharacteristics as the recommended replacement partmight create shock, fire and / or other hazards. Productsafety is under review continuously and newinstructions are issued whenever appropriate.

Components identified by on schematics and partslists must be sealed by a soldering iron afterreplacement and adjustment.

AN15V* 1-1

1 Precautions

1-1 Safety Precautions

!

DEVICEUNDERTEST

TEST ALLEXPOSED METAL

SURFACES

(READING SHOULDNOT BE ABOVE 0.5mA)

LEAKAGECURRENTTESTER

2-WIRE CORD

ALSO TEST WITHPLUG REVERSED

(USING AC ADAPTERPLUG AS REQUIRED) EARTH

GROUND

CONFIDENTIAL

1. Servicing precautions are printed on the cabinet,and should be followed closely.

2. Always unplug the unit’s AC power cord from theAC power source before attempting to: (a) removeor reinstall any component or assembly, (b)disconnect PCB plugs or connectors, (c) connect alltest components in parallel with an electrolyticcapacitor.

3. Some components are raised above the printedcircuit board for safety. An insulation tube or tapeis sometimes used. The internal wiring issometimes clamped to prevent contact withthermally hot components. Reinstall all suchelements to their original position.

4. After servicing, always check that the screws,components and wiring have been correctlyreinstalled. Make sure that the area around theserviced part has not been damaged.

1. Immediately before handling any semiconductorcomponents or assemblies, drain the electrostaticcharge from your body by touching a known earthground. Alternatively, wear a discharging wrist-strap device. To avoid a shock hazard, be sure toremove the wrist strap before applying power tothe monitor.

2. After removing an ESD-equipped assembly, place iton a conductive surface such as aluminum foil toprevent accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These cangenerate electrical charges sufficient to damageESDs.

4. Use only a grounded-tip soldering iron to solder ordesolder ESDs.

5. Use only an anti-static solder removal device. Somesolder removal devices not classified as “anti-static”can generate electrical charges sufficient to damageESDs.

5. Check the insulation between the blades of the ACplug and accessible conductive parts (examples:metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect thepower cord from the AC source and turn the powerswitch ON. Connect an insulation resistance meter(500 V) to the blades of the AC plug.

The insulation resistance between each blade of theAC plug and accessible conductive parts (seeabove) should be greater than 1 megohm.

7. Never defeat any of the +B voltage interlocks. Donot apply AC power to the unit (or any of itsassemblies) unless all solid-state heat sinks arecorrectly installed.

8. Always connect a test instrument’s ground lead tothe instrument chassis ground before connectingthe positive lead; always remove the instrument’sground lead last.

6. Do not remove a replacement ESD from itsprotective package until you are ready to install it.Most replacement ESDs are packaged with leadsthat are electrically shorted together by conductivefoam, aluminum foil or other conductive materials.

7. Immediately before removing the protectivematerial from the leads of a replacement ESD,touch the protective material to the chassis orcircuit assembly into which the device will beinstalled.

Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions.

8. Minimize body motions when handlingunpackaged replacement ESDs. Motions such asbrushing clothes together, or lifting your foot froma carpeted floor can generate enough staticelectricity to damage an ESD.

9. Indicates ESDs on the Schematic Diagram inthis manual.

1 Precautions

1-2 AN15V*

CONFIDENTIAL

1-3 Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonlycalled Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

1-2 Servicing Precautions

WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances

create conflict between the servicing precautions and safety precautions, always

follow the safety precautions.

WARNING2: A high voltage adjusted to the wrong value may cause excessive X-ray emissions.

WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.

AN15V* 2-1

2 Product Specifications

2-1 Specifications

Picture Tube: 15-Inch (38 cm): 13.8-inch (35 cm) viewable,Full-square flat-face tube, 90˚ Deflection, Semi- tint, Non-glare, Invar shadow mask,Anti-static silica coating, 0.28 mm Dot pitch

Scanning Frequency Horizontal 30 KHz ~ 55 KHz (Automatic) Vertical 50 Hz ~ 120 Hz (Automatic)

Display Colors Unlimited colors

Maximum Resolution Horizontal 1024 Dots Vertical 768 Lines

Input Video Signal Analog, 0.7 Vp-p positive at 75 Ω, internally terminated

Input Sync Signal Separate Sync : TTL level positive/negative

Maximum Pixel Clock rate 65 MHz

Active Display Horizontal : 267 mm ± 4 mm, Vertical : 200 mm ± 4 mm

Input Voltage AC 90 ~ 264 Volts, 60 Hz / 50 Hz ± 3 Hz

Power Consumption 80 Watt (max)

Dimensions (W x D x H)With Base 14.01 x 14.92 x 14.54 Inches (356 x 379 x 369.5 mm)

Weight (Net/Gross) 11.5 kg (25.35 lbs) / Standard : 13.3 kg (29.32 lbs), Special : 13.4 kg (29.54 lbs)

Environmental Considerations Operating Temperature : 32°F ~ 104°F (0°C ~ 40°C)Humidity : 10 % ~ 80 %Storage Temperature : –4°F ~ 113°F (–20°C ~ 45°C)Humidity : 5 % ~ 95 %

• Above models comply with SWEDAC (MPR II) recommendations for reduced electromagnetic fields.• Designs and specifications are subject to change without prior notice.

Item Description

CONFIDENTIAL

CONFIDENTIAL2 Product Specifications

2-2 AN15V*

2-2 Pin Assignments

5

15

Figure 2-1. Male Type Figure 2-2. Male Type

SyncType

Pin No.MacintoshSeparate

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Red

Green

Blue

N-C

GND (DDC Return)

GND-R

GND-G

GND-B

N-C

GND-Sync./Self-Test

N-C

DDC Data

H-Sync.

V-Sync.

DDC Clock

GND-R

Red

H/V Sync.

Sense 0

Green

GND-G

Sense 1

Reserved

Blue

Sense 2

GND

V-Sync.

GND-B

GND

H-Sync.

2 Product Specifications

AN15V* 2-3

Q R S

P

O

Video

Sync Sync

Horizontal Vertical

C D E

P

O

B

A

Video

Sync Sync

Separate Sync

2-3 Timing Chart

This section of the service manual describes the timing that the computer industry recognizes as standardfor computer-generated video signals.

C D

A O

E

B P

Video

Sync Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width

C : Back porch D : Active time Q : Back porch R : Active time

E : Front porch S : Front porch

fH (kHz)

A µsec

B µsec

C µsec

D µsec

E µsec

fV (Hz)

O msec

P msec

Q msec

R msec

S msec

ClockFrequency(MHz)

PolarityH.Sync

V.Sync

Remark

IBM VESA

800/85 Hz800 x 600

VGA3/60 Hz640 x 480

VGA2/70 Hz720 x 400

31.469

31.778

3.813

1.907

25.422

0.636

70.087

14.268

0.064

1.080

12.711

0.413

28.322

Negative

Positive

Separate

31.469

31.778

3.813

1.907

25.422

0.636

59.940

16.683

0.064

1.048

15.253

0.318

25.175

Negative

Negative

Separate

43.269

23.111

1.556

2.222

17.778

1.556

85.008

11.764

0.671

0.578

11.093

0.023

36.000

Negative

Negative

Separate

53.674

18.631

1.138

2.702

14.222

0.569

85.061

11.756

0.056

0.503

11.179

0.019

56.250

Positive

Positive

Separate

640/85 Hz640 x 480

Table 2-1 Timing Chart

Mode

Timing

37.500

26.667

2.032

3.810

20.317

0.508

75.000

13.333

0.080

0.427

12.800

0.027

31.500

Negative

Negative

Separate

640/75 Hz640 x 480

CONFIDENTIAL

CONFIDENTIAL2 Product Specifications

2-4 AN15V*

Memo

3-1-1 Before making Disassembly1. Disconnect or power cord from the monitor.2. With a pad beneath it, stand the monitor on its

front with the screen facing downward andthe base close to you.

3-1-2 Cabinet Disassembly1. Remove the Stand from the monitor.

(Refer to Stand manual)2. Remove 2 screws on the Rear cover.

3. Incline the monitor by lifting the rear of themonitor.

4. Push the Opening jig each groove along thetop of the monitor till it makes a “ttak” sound.(2 grooves : Left and Right, Make sure eachsnap is disengaged.)

5. Pull the Rear Cover up off the monitor.

AN15V* 3-1

3 Disassembly and ReassemblyThis section of the service manual describes the disassembly and reassembly procedures for theAN15V* monitor.

WARNING: This monitor contains electrostatically sensitive devices. Use with caution whenhandling these components.

3-1 Disassembly

Cautions:1. Disconnect the monitor from the power source before disassembly.2. To remove the Rear Cover, you must use the special opening jig tool.

Figure 1

Figure 2

Figure 3

Figure 4

CONFIDENTIAL

6. Remove the Shield.(TCO 95)

7. Using pinch-nose pliers or ling-nose pliers,acrefully disconnect the Anode Cap from theCRT.

Warning: Do not touch the Anode contacton the CRT (High Voltage mayremain).

3-1-3 Removing the CRT Socket PCB1. Complete all previous steps.2. Lift up the Video Spring and remove the CRT

Socket PCB from the CRT.

3. Disconnect all connectors on the CRT SocketPCB.

4. Using a solder iron, disconnect Ground (GND)on the back of the Video Shield and removethe Shield Cap.

5. Remove the screw on the front of the ShieldSocket.

6. Desolder the 4 tabs on the CRT Socket PCBand remove Shield.

7. Place the Video PCB on a flat, level surfacethat is protected from static electricity.

3-1-4 Removing the Main PCB1. Complete all previous steps.2. Disconnect the Degaussing Coil at CN603 on

the Main PCB.3. Disconnect all easily accessible ground wires

on the PCB and Bottom Chassis.4. Disconnect the DY connector at the CN404

connector on the Main .5. Using the jig, release the snaps (2) connecting

the Front Cover and the PCB then lift up theBottom to separate the two Shield.

6. Disconnect the Sub PCB connector at theCN201 connector on the Main PCB.

7. Remove the screws on the back and alongeach side of the Bottom Chassis.

8. Carefully lift the Main PCB Ass’y and removethe remaining ground wires.

9. Place the Main PCB Ass’y on a flat, levelsurface that is protected from static electricity.

3-1-5 CRT Ass’y Disassembly1. Complete all previous steps.2. Straighten the Degaussing Coil Assembly

coated metal ties and lift the Coil Ass’y fromthe CRT.

3. Remove the four corner screws and lift theCRT up and away from the Front CoverAssembly and place it on a padded surface.

Caution: Do not lift the CRT by the neck.If you will be returning this CRT tothe monitor, be sure to place the CRTface downward on a protective pad.

3 Disassembly and Reassembly

3-2 AN15V*

CONFIDENTIAL

3-2 Reassembly

Reassembly procedures are in the reverse order of Disassembly procedures.

Figure 6

Figure 7

Figure 5

4-1-1 Before Making Adjustments

4-1-1 (a) ORIENTATIONWhen servicing, always face the monitor to theeast.

4-1-1 (b) WARM-UP TIMEThe monitor must be on for 30 minutes beforestarting alignment. Warm-up time is especiallycritical in color temperature and white balanceadjustments.

4-1-1 (c) SIGNALAnalog, 0.7 Vp-p positive at 75 ohm, internalterminationSync: TTL level, negative/positive

4-1-1 (d) SCANNING FREQUENCY

Horizontal: 30 KHz ~ 55 KHz (Automatic)Vertical: 50 Hz ~ 120 Hz (Automatic)

Unless otherwise specified, adjust at the 800 x 600 mode (54 KHz/85 Hz).

4-1-2 Required Equipment

The following equipment may be necessary foradjustment procedures:

4-1-2 (a) DISPLAY CONTROL ADJUSTMENT1. Non-metallic (–) screwdriver:

1.5, 2.5, 3 mm2. Non-metallic (+) screwdriver:

1.5, 2.5, 3 mm3. Digital Multimeter (DMM), or

Digital Voltmeter4. Signal generator, or

DM200 software5. Personal computer

4-1-2 (b) COLOR ADJUSTMENTS1. All equipment listed in 4-1-2 (a), above2. Color analyzer, or any luminance

measurement equipment

AN15V* 4-1

4 Alignment and AdjustmentsThis section of the service manual explains how to make permanent adjustments to the monitor. Directionsare given for adjustments using the monitor Interface Board Ver. 1.1 and software (Softjig).

4-1 Adjustment Conditions

Caution: Changes made without the Softjig are saved only to the user mode settings. As such, thesettings are not permanently stored and may be inadvertently deleted by the user.

CONFIDENTIAL

4 Alignment and Adjustments

4-2 AN15V*

CONFIDENTIAL

4-2-1 HIGH VOLTAGE Signal: 800 x 600 (54 KHz/85 Hz)Display image: Full White PatternContrast: Maximum Brightness: Maximum Limit: 25.0 kV ± 0.2 kVMeasure the hight voltage level at the anode cap.High voltage should be within the limit as above.

4-2-2 CENTER RASTERAdjust VR401 so that the back raster comes to thecenter when you apply each basic mode.

SCREEN VOLTAGE ADJUSTMENT This can only SDI CRT conditions.Signal: 800 x 600 (54 KHz/85 Hz)Display image: Don’t careContrast: Minimum Brightness: Minimum Limit: 480 ± 10V

Adjust screen VR of T501.

4-2-3 CenteringCentering means to position the center point ofthe display in the middle of the display area.Horizontal size and position and vertical size andposition control the centering of the display.

Adjust the horizontal size and vertical size to theiroptimal settings: 267 mm (H) x 200 mm.

Adjust the horizontal position and verticalposition to ≤ 5.0 mm of the center point of thescreen.

|A – B| ≤ 5.0 mm. |C – D| ≤ 5.0 mm.

Figure 4-3. Centering

4-2-3 (a-1) HORIZONTAL SIZE ADJUSTMENT

CONDITIONSScanning frequency: 54 KHz/85 HzDisplay image: Crosshatch patternBrightness: MaximumContrast: Maximum

Use control bar after selecting “SIZE B+” in leftmenu to adjust the horizontal size of the displaypattern to 255 mm . (Tolerance: ± 4 mm.)

4-2-3 (a-2) HORIZONTAL SIZE ADJUSTMENTUse control bar after selecting “H-SIZE” in leftmenu to adjust the horizontal size of the displaypattern to 267 mm . (Tolerance: ± 4 mm.)

4-2-3 (b) VERTICAL SIZE ADJUSTMENT

CONDITIONSScanning frequency: 54 KHz/85 Hz Display image: Crosshatch patternBrightness: MaximumContrast: Maximum

Use control bar after selecting “V-SIZE” in leftmenu to adjust the vertical size of the displaypattern to 200 mm. (Tolerance: ± 4 mm.)

4-2-3 (c) HORIZONTAL POSITION ADJUSTMENT

CONDITIONSScanning frequency: 54 KHz/85 Hz Display image: Crosshatch pattern

Use control bar after selecting “H-POSITION” inleft menu to center the horizontal image on theraster.

4-2-3 (d) VERTICAL POSITION ADJUSTMENT

CONDITIONSScanning frequency: 54 KHz/85 Hz Display image: Crosshatch pattern

Use control bar after selecting “V-POSITION” inleft menu to center the vertical image on theraster.

4-2-4 LinearityLinearity affects the symmetry of images as theyappear on the screen. Unless each row or columnof blocks in a crosshatch pattern is of equal size,or within the tolerances shown in Table 4-1 animage appears distorted, elongated or squashed.

Horizontal Linearity = 2x x100

Vertical Linearity = 2x x100

Table 4-1

Preset Mode : 54KHz / 85HzPre-load Mode : Refer to Timing Chart

4-2 Display Control Adjustments

C

A

DISPLAY AREA

EDGE OF BEZELB

DX max-X minX max+X min

Y max-Y minY max+Y min

Preset mode ≤ 4% ≤ 8%

Adjacent Linearity Entire Linearity

Pre-load mode (48kHz~) ≤ 5% ≤ 14%

4-2-4 (a) HORIZONTAL LINEARITY ADJUSTMENTCONDITIONSScanning frequency: 54 KHz/85 Hz Display image: Crosshatch patternBrightness: MaximumContrast: MaximumTo adjust the Horizontal Linearity, refer to Table4-1 for the tolerance range.Increase or decrease H_LIN to optimize theimage.

4-2-4 (b) VERTICAL LINEARITY ADJUSTMENT

CONDITIONSScanning frequency: 54 KHz/85 HzDisplay image: Crosshatch patternBrightness: MaximumContrast: MaximumTo adjust the Vertical Linearity, refer to Table 4-1for the tolerance range.Use control bar after selecting “V-LINEARITYBAL” in left menu to optimize the image.

4-2-5 Trapezoid AdjustmentCONDITIONSScanning frequency: 54 KHz/85 HzDisplay image: Crosshatch patternBrightness: MaximumContrast: Maximum

Use control bar after selecting “TRAPEZOID” inleft menu to make the image area rectangular.

Figure 4-4. Trapezoid

4-2-6 Pinbalance AdjustmentCONDITIONSScanning frequency: 54 KHz/85 HzDisplay image: Crosshatch patternBrightness: MaximumContrast: Maximum

Use control bar after selecting “PINBALANCE” inleft menu to optimize the image.

4-2-7 Parallelogram AdjustmentCONDITIONSScanning Frequency: 54 KHz/85 HzDisplay image: Crosshatch patternBrightness: MaximumContrast: Maximum

Use control bar after selecting “PARALLEL” inleft menu to make the image area rectangular.

Figure 4-6. Parallelogram

4-2-8 Side Pincushion Adjustment

CONDITIONSScanning frequency: 54 KHz/85 HzDisplay image: Crosshatch pattern

Use control bar after selecting “PINCUSHION” inleft menu to straighten the sides of the image area.

4-2-9 Degauss

No adjustments are available for the degaussingcircuit. The degaussing circuit can effectivelyfunction only once per 30 minutes.

4-2-10 To Delete the User Mode DataTo delete the adjustment data from the usermodes, click “@4: USER DELETE” in right ment.

4-2-11 Save the DataTo save the adjustment data for a mode, press“@3: ALL MODE SAVE” in right ment.


AN15V* 4-3

CONFIDENTIAL

| A – B | < 4 mm

A

B B

A

D1 D2 D1

Figure 4-5. Pinbalance

| D1 |, | D2 | ≤ 2.0 mm

4 mm

Figure 4-7. Pincushion

| C1 |, | C2 | ≤ 2.0 mm, | D1 |, | D2 | ≤ 2.0 mm.

D1

C2

D2

C1


4-4 AN15V*

CONFIDENTIAL

CAUTION : Check below condition before coloradjustment Video signal : Analog 0.7Vp-p (at 75 Ω)Sync : TTL level (H, V seperatesignal)

* Select “Color” in Softjig menu for color adjustment.

4-3-1 Color Coordinates (Temperature)

Color temperature is a measurement of theradiant energy transmitted by a color. Forcomputer monitors, the color temperature refersto the radiant energy transmitted by white. Colorcoordinates are the X and Y coordinates on thechromaticity diagram of wavelengths for thevisible spectrum.

CONDITIONSMeasurement instrument: Color analyzerScanning frequency: 54 KHz/85 HzDisplay image: White flat field at

center of display areaLuminance: Maximum

PROCEDUREUse the directions in sections 4-3-2 through 4-3-3to adjust the color coordinates for:9300K to x = 0.283 ± 0.015, y = 0.298 ± 0.0156500K to x = 0.313 ± 0.015, y = 0.329 ± 0.015

4-3-2 Color Adjustments for 9300K

4-3-2 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONSScanning frequency: 54 KHz/85 HzDisplay image: Back raster patternBrightness: MaximumContrast: Maximum

1. Select “@1: CHANNEL 1” in right menu tocontrol the color for 9300K.

2. Adjust the luminance of the back raster tobetween 0.5 to 0.7 ft-L using contron bar afterselecting “GREEN CUTOFF” in the menu.

3. Use control bar after selecting “BLUECUTOFF” in left menu to set the “y”coordinate to 0.298 ± 0.015

4. Use control bar after selecting “REDCUTOFF” in left menu to 0.283 ± 0.015

* If color values would not be matched desirable values, repeat sequence 3 and 4 after readjusting“GREEN CUTOFF” control a little different.

4-3-2 (b) WHITE BALANCE ADJUSTMENTCONDITIONSScanning frequency: 54 KHz/85 Hz Display image: White box patternBrightness: 0.06ft-L at Back Raster

Pattern DisplayContrast: Maximum

1. Use control bar after selecting “RED GAIN”,“GREEN GAIN” and “BLUE GAIN” to adjustthe luminance to 50 ft-L with the colorcoordinates ranged for 9300K to x = 0.283 ± 0.015, y = 0.298 ± 0.015.

Figure 4-8. White Box Pattern

4-3-2 (c) ABL ADJUSTMENT

CONDITIONSScanning frequency: 54 KHz/85 Hz Display image: Full white patternBrightness: MaximumContrast: Maximum

Figure 4-9. Full White Pattern

1. Check the ABL. If it is not within thespecifications, use the ABL controls to adjustit. (38 ± 1 ft-L )

2. Select “@4: COLOR SAVE” to save the data.3. Select “@6: ALL COLOR SAVE” to save the

CH2.

4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION

CONDITIONSScanning frequency: 54 KHz/85 Hz

1/3H-1/2H

1/3V-1/2V

FRONT BEZEL OPENING

BACK RASTER

WHITE WINDOW

FRONT BEZEL OPENING

BACK RASTER

WHITE WINDOW

4-3 Color Adjustments


AN15V* 4-5

CONFIDENTIALDisplay image: Back raster pattern

Full White PatternX-Y Coordinates: x = 0.283 ± 0.015,

y = 0.298 ± 0.015ABL Luminance Refer to 4-3-2(c)Brightness: MaximumContrast: 5 ft-L, 24 ft-L

1. Check whether the color coordinates of theback raster satisfy the above spec.If they do not, return to 4-3-2 (a) and readjustall settings.

2. Display a full white pattern.

3. Select “Geometry” in softjig menu.4. Select “@7: 5-ft “ in right menu.5. Check whether the white coordinates of the

video meet the above coordinates spec.6. Select “@8: 24-ft “ in right menu.7. Check whether the white coordinates of the

video satisfies the above spec.If they do not, return to 4-3-2 (a) and readjustall settings.

Select “Color” and click “@2: CHANNEL 2”for color ajdustment for 6500KRepeat the sequence of 9300K adjustment.The luminance values the same as 9300K, butthe color coordinated of back raster and whitebox are : x = 0.313 ± 0.015 y = 0.329 ± 0.015

4-3-3 Luminance Uniformity Check

Luminance is considered uniform only if the ratioof lowest to highest brightness areas on the screenis not less than 7.5:10.


(800 x 600)Display image: White flat fieldBrightness: Cut off point at 24 ft-LContrast: Maximum

PROCEDUREMeasure luminance at nine points on the displayscreen (see figure below).

4-3-4 Focus Adjustment


(800 x 600)Display image: “H” character patternBrightness: Cut off pointContrast: Maximum

PROCEDURE1. Adjust the Focus VR on the FBT to display the

sharpest image possible.2. Use Locktite to seal the Focus VR in position.

4-3-5 Color Purity AdjustmentColor purity is the absence of undesired color.Conspicuous mislanding (unexpected color in auniform field) within the display area shall not bevisible at a distance of 50 cm from the CRTsurface.

CONDITIONSOrientation: Monitor facing eastScanning frequency: 54 KHz/85 HzDisplay image: White flat fieldLuminance: Cut off point at the center

of the display area

Note: Color purity adjustments should only beattempted by qualified personnel.

PROCEDUREFor trained and experienced service technicians only.

Use the following procedure to correct minorcolor purity problems:

1. Make sure the display is not affected byexternal magnetic fields.

2. Make sure the spacing between the PCMassembly and the CRT stem is 29 mm ± 1 mm.

3. Display a green pattern over the entire displayarea.

4. Adjust the purity magnet rings on the PCMassembly to display a pure green pattern.(Optimum setting: x = 0.295 ± 0.015, y = 0.594 ± 0.015)

Table 4-2. Color Purity Tolerances(For 9300K color adjustment: x = 0.283 ± 0.015, y = 0.298 ± 0.015)

5. When you have the PCMs properly adjusted,carefully glue them together to prevent theirmovement during shipping.Figure 4-10. Luminance Uniformity Check Locations

Red: x = 0.640 ± 0.015 y = 0.323 ± 0.015

Green: x = 0.295 ± 0.015 y = 0.594 ± 0.015

Blue: x = 0.142 ± 0.015 y = 0.066 ± 0.015

Memo


4-6 AN15V*

CONFIDENTIAL

CONFIDENTIAL

AN15V* 5-1

5 Troubleshooting

5-1 Parts Level Troubleshooting

Notes: Check the following circuits.• No raster appears: Power circuit, Horizontal output circuit.• High voltage develops but no raster appears: Video output circuits.• High voltage does not develop: Horizontal output circuits.

5-1-1 No Power Supply

Chirping noise exists? Check and replace IC601.

Check and replace D601 and FH_1.

Done.

No

Yes

Repeating start? Check and replace D606.

No

Yes

IC601 Pin 1 waveform is right? Check and replace Q602, IC605,OP202 and IC602.

Yes

No

C622 Voltage is 13 V ± 0.5V?Check and replace IC201, IC301,

IC401, IC605, Q402,Q404, Q613,and Q614.

Yes

No

Operate normally? Replace Main board.

Yes

Verify voltages.

No

1

WAVEFORMS

1 100 V (IC601, #1)

CH1 P-P = 100 V CH1 RMS = 350.2 V

CONFIDENTIAL5 Troubleshooting

5-2 AN15V*

5-1-2 DPMS Failure

Make No H/V Sync.(power off mode)

Check signal source H/V Sync. video level.

LED blinks? Check IC201 Pin 40.

Yes

No

+12 V line off? Check IC201 Pin 5, Pin 6 and Q610,Q602 operation condition.

Yes

No

Q602 Basevoltage exists? Refer to 5-1-1 No Power Supply.

Done

Yes

No

IC601 Pin 1 Outputvoltage exists?

Check IC201 Pin 5.Check and replace Q602 and IC201.

No2

WAVEFORMS

2 100 V (IC601, #1)

CH1 P-P = 100 V CH1 RMS = 325.8 V


AN15V* 5-3

5-1-3 H_Deflection Failure

Does Horizontal pluse signalappear at at Pin 26 of IC605? Check IC605.

Yes

No

Does 20 Vp-p signal appear at Collector of Q400? Check Q400.

Yes

No

Check D406, Q404 and T401.

4

Does PWM output signal appear at Pin 28 (B_drv) of IC605?

Check IC605.

Check 12 V line.

Yes

No Does DC 12V appear at Pin 29 of IC605?

Yes

No3

5-1-4 S Correction Failure

S1~S2 signals are right at eachfrequency block?

Check S1 ~ S2 signal.

Check and replace Q404, Q410, Q411, Q415, and Q416.

Yes

Check and replace IC201.No

5

WAVEFORMS

3 5.00 V (IC605, #28)

4 1.00 V (IC605, #26)

5 5.00 V (Q400, Collector)


5-4 AN15V*

5-1-5 H_Lin. Failure Check and replace T402

5-1-6 Invariable H_Size

IC605 Pin 28 voltage varies withdifferent B_Drv DAC values?

Q402 Gate output duty varies withdifferent B_Drv DAC values?

Check some parts around Q402, IC605 Pin 4 ~ 6.

Yes

No


5-1-7 Abnormal H_Size

IC605 Pin 24 output duty varies with different B+ offset

DAC values?

Q408 Collector waveform isright?

Check and replace Q405, Q406, Q407, and Q408.

Check some parts around D409 and L401.

Yes

Yes

No


6

WAVEFORMS



AN15V* 5-5

5-1-8 Side Pin or Trap Failure

IC605 Pin 24 output exists?

Yes

Check and replace IC605.

Refer to 5-1-7 Abnormal H_Size.

5-1-9 Para. or Pin Balance Failure

IC605 Pin 24 output varies withdifferent DAC values?

No

Replace IC605.

No7

Refer to 5-1-7 Abnormal H_Size.Yes

WAVEFORMS

7 1.00 V (IC605, #24)


5-6 AN15V*

5-1-10 V Deflection Failure

13V and –10V lines are on?

IC605 Pin 23 output exists? Check and replace IC605.

Yes

Yes

No

Refer to 5-1-1 No Power SupplyNo

IC300 Pin 6 output exists? Check and replace some parts around IC300.

Yes

No

Check DY connector connection.

8

9

5-1-11 V Size or Position Variation Failure

IC605 Pin 23 output varies withdifferent DAC values?

Yes

Check and replace IC201 and IC605.


No

WAVEFORMS

8 1.00 V (IC605, #23)

9 10.0 V (IC300, #6)


AN15V* 5-7

5-1-12 High Voltage Failure

IC605 Pin 28 OSC pulse exists?

Q402 Gate driving pulse exists? Check and replace Q401, Q417.

Yes

Yes

No

Check and replace IC605and +12 V line.

No

Q402 Drain pulse exists? Check and replace Q402, D401Check 50V line and L402.

Yes

No

Done

10

3

IC101 Pin 8 input exists and varies with different patterns? Check and replace IC101.

Input full white pattern to monitor.

Yes

No

T501 Pin 8 output exists? Check and replace T501.

Yes

No

IC201 Pin 26 output exists andvaries with different patterns? Check and replace IC201.

Yes

No

Done

Check CN102.

5-1-13 ABL Failure

11

WAVEFORMS

3 5.00 V (IC605, #28)

CH1 P-P = 2.00 V CH1 RMS = 5.868 V

10 5.00 V (Q402, Gate)

CH1 P-P = 2.00 V CH1 RMS = 7.692V

11 50.0 V (Q402, Drain)

CH1 P-P = 50.0 V CH1 RMS = 73.7V


5-8 AN15V*

5-1-14 Dynamic Focus Failure (This comonly TSB CRT)

T502 Pin 6 output is right?

Yes

Replace the C432.No

T502 Pin 1 input is right? Check and replace T502.

Yes

No

Check the connection between FBTFocus pin and CRT Socket PCB.

13

12WAVEFORMS

12 50.0 V (T502, #6)

CH1 P-P = 50.0 V CH1 RMS = 75.6 V

13 100 V (T502, #1)

CH1 P-P = 100V CH1 RMS = 124.0 V


AN15V* 5-9

5-1-15 No Video

IC101 Pin 12, 14 and 16 inputs are right?

IC101 Pin 18, 21 and 24 outputs are right? Check I2C bus and +12V line.

Yes

Yes

No

Check the signal cable connection.No

IC102 Pin 9, 10 and 11 outputs are right?

Check +12V, +80V line. Check and replace IC102.

Yes

No

Cathode DC levels are right? Check +80V line.Check and replace IC104.

Yes

No

G2 voltage is right? Check G2 wire, CRT Socket board and FBT.

Change CRT.

Yes

Done.

No

Check signal cable and connection.

14

15

16

WAVEFORMS

14 1.00 V (IC101 #12,14,16)

15 0.5 V (IC101 #18,21,24)

16 20.0 V (IC102, #9,10,11)


5-10 AN15V*

5-1-16 Micom Failure

IC201 Pin 11 input voltage is 5V?

IC201 Pin 13 and 14inputs are right? Check C202, C203 and X201.

Yes

Yes

No

Check Q608.No

IC201 Pin 18 input is right? Check and replace IC201 and R206.

Yes

No

All in/output values are right? Replace IC201.

Yes

No

Done

17

WAVEFORMS

17 2.00 V (IC201, #13, 14)


AN15V* 5-11

5-1-17 OSD Failure

IC101 Pin 32 input is right?

IC101 Pin 1 input is right? Check CN102 Pin 8.

Yes

Yes

No

Check CN102 Pin 14.Check and replace R117,

C117 and IC101.

No

IC101 Pin 29 and 30 inputs are right? Check IC201 Pin 41 and 42.

Yes

No

IC101 Pin 18, 21 and 24 outputs are right? Check and replace IC101.


Yes

Done

No

18

19

20

Check CN102 and connector Assy.WAVEFORMS

18 2.00 V (IC101, #32)

19 2.00 V (IC101, #1)

20 1.00 V (IC101, #18,21,24)


5-12 AN15V*

5-1-18 User Control Failure

Does the DC level change at Pin 38 of IC201 when you

push the button S/W?

Yes

Check the button.(SW201 ~ SW204)

No

Check IC201.

RL601 operation is right?

Q601 base input is right? Check and replace Q601.

Yes

Yes

No

Check D-coil and TH601.No

IC201 Pin 4 output is right? Check and replace IC201.

Yes

No

Done

Check degaussing connector.

5-1-19 Degaussing Failure


AN15V* 5-13

5-2 General Troubleshooting

5-2-1 No Picture

LED blinks?

LED is green color? Check Micom.

Check G2 voltage, high voltage and R, G, B cathode voltage.

Yes

Yes

No

Refer to 5-2-2 Shut down.No

5-2-2 Shut Down

Blinking LED’s?

Scan failure?Check horizontal, vertical deflection

system and check power supplysecondary voltages.

Yes

Yes

Check power supply.No


Done

No

Video failure? Check Video board.

No

Yes


5-14 AN15V*

5-2-3 Missing Color

Proper Video levels areon CN101 (D-Sub) Pin 1, 3 and 5?

Proper Video signal ison all cathodes? Refer to 5-1-15 No Video.

Yes

Yes

No

Check signal generator.No

Proper DC voltage ison all cathodes?

Check IC101 Pin 17, 20 and 23.Check IC104.

Yes

Yes

No

G2 voltage is right? Check T501. No

Heater voltage is right? Check D608, Q604 and T601.No

Yes

Check D504, Q502 and T501.No

Yes

Yes

G1 voltage is right?No

Replace CRT.

Done

21

WAVEFORMS

21 10.0 V (R,G,B, Video)

CH1 P-P = 10.0V CH1 RMS = 17.02V


AN15V* 5-15

G2 voltage is right?

Blank pulse is on Pin 3 of IC605? Check IC605.

Yes

Yes

No

Check T501.No

V_FLB pulse is on Collector of Q502? Check Q502.

Done

Yes

No

Does approve the Vertical pulse on the CRT Socket G1? Check CN102 and CN201.

Yes

No

Check white balance adjustment.

5-2-4 Visible Retrace

22

23

WAVEFORMS


23 50.00 V (CRT Socket, G1)


5-16 AN15V*

Signals are right?

Signals at Pin 28 and 29 of IC201 are right? Check IC201.

Yes

Yes

No

Check Video Cable.No

Signals at Pin 1 and 2 of IC605 are right? Check IC605.

Check circuits on Main board.

Yes

Done

No

Check input signals Pin 2 and 3 of CN202.

5-2-5 Unsynchronized Image


AN15V* 5-17

The convergence is now within spec.?

Readjust convergence.

No

DoneYes

The convergence is now within spec.? Done

Yes

Change CRT and readjustconvergence.

No

Done

Try readjusting convergence.

5-2-6 Misconvergence


5-18 AN15V*

Improved focus?

Check focus leads from FBT to CRT Socket.

Check the CRT Socket.

No

Aging monitor and check for focuschange.

Yes

Dynamic focus circuit is right? Refer to 5-1-14 Dynamic Focus Failure.

Replace the CRT and verify focus.

Yes

No

Adjust focus VR of FBT.

5-2-7 Poor Focus

5-2-8 Purity Failure

Purity is right?

Degaussing circuit is right? Refer to 5-1-19 Degaussing Failure.

Replace CRT and verify purity.

Yes

No

No

DoneYes

Degaussing

(SDI CRT)

(Toshiba CRT)

CONFIDENTIAL

AN15V* 6-1

6 Exploded View and Parts List

6-1 AN15VS

6-2 AN15VT

6 Exploded View & Parts List

6-2 AN15V*

CONFIDENTIAL

CONFIDENTIAL

AN15V* 7-1

- BH94-00827C ASSY PCB MAIN AN15VS SNAAN_LABEL BH68-00446D LABEL AN-STICKER,ART-PAPER 100G,15,15,BLACK,YELLOWC409 2306-000248 C-FILM,MPPF 680nF,5%,250V,BK,26.5x16.5mm,2C419 2301-001206 C-FILM,PPF 4.4nF,5%,2.5KV,BK,29x21x13,20C601 2301-001195 C-FILM,MPPF 150nF,10%,275VAC,BK,26x16.5x7,C602 2301-001195 C-FILM,MPPF 150nF,10%,275VAC,BK,26x16.5x7,C608 2401-003392 C-AL 180uF,20%,450V,GP,BK,25x45,10CIS BH39-00405A CBF SIGNAL AN15/17**,15P/06P,07P,20276-N,1500MM,UL20276,IVORY,D-SUB/MALE,ATT. TYPECIS1 0201-001096 ADHESIVE-HM #3748,YEL,8500CPS,- SNACIS11 BH71-00110A SHIELD BOTTOM PN15VT,SECC ,T1.0 SNACIS12 BH68-00001A LABEL-MARK CDT ART-PAPER 100G,-,WHT,BLK,-,ALL,CDT SNACIS13 BH72-00025A GUIDE-POWER CDA4507,ABS,V0,IV16 SNACIS14 BH72-00026A SHAFT-POWER CDA4507,ABS,V0,IV16 SNACIS15 BH72-00261A SHEET ABS-LMF IB10LO,AL+PET,-,-,-,-,-,- SNACIS16 BH73-60304C RUBBER-SUPPORT DP15LT,CR V0,GRAY,-,14*7*10,-,- SNACIS2 0202-001044 SOLDER-WIRE. S63S-W3.0,S63S,D3,63Sn/37Pb,- SNACIS21 6502-000001 CABLE CLAMP DAWH-5NB,D15,L35,NYLON66,NTR SNACIS22 6502-000001 CABLE CLAMP DAWH-5NB,D15,L35,NYLON66,NTR SNACIS3 0202-001046 SOLDER-WIRE FLUX CF-110VH-2A,-,-,-,- SNACIS31 BH39-00323D LEAD CONNECTOR-ASSY OT17LO,8.0*0.16TA*16,35068-9822,35750-1010,BK,150MM,8.0*0.16TA*16CIS4 0202-001222 SOLDER-WIRE FLUX RS-107,RS60-1.2AA,D1.2,SN60/PB40,- SNACIS5 0204-001095 THINNER #4520,-,-,- SNACN201 3711-003895 CONNECTOR-HEADER BOX,13P,1R,2mm,STRAIGHT,SN SNACN202 3711-003873 CONNECTOR-HEADER BOX,7P,1R,2mm,STRAIGHT,SN SNACN404 3711-003989 CONNECTOR-HEADER NOWALL,4P,1R,8mm,STRAIGHT,SN SNACN502_WIRE BH39-00401A LEAD CONNECTOR-ASSY DT15LT,UL1007#22,UL/CSA,3(2)P,BLK,#22,YBNH250-03,BK,170MM,1007#22CN601 3721-001053 PLUG-AC POWER 3P,-,-,NICN604 BH39-00288A CBF HARNESS PN17LO,UL1007,UL/CSA,2P/2P,130MM,BLU/WHT,AWG26,YBNH200,SMP250,-,-,-,-,-,-,CBF-COD406 0402-001025 DIODE-RECTIFIER ERD07-15,1.5KV,1.5A,-,TPD409 0402-001295 DIODE-RECTIFIER GUR460L-5700,600V,4A,DO-201AD,BKD601 0402-000103 DIODE-BRIDGE D2SBA60,600V,1.5A,SIP-4,STD608 0402-000016 DIODE-RECTIFIER UF5404,400V,3A,DO-201AD,TPD609 0402-001295 DIODE-RECTIFIER GUR460L-5700,600V,4A,DO-201AD,BKFBT_CORE 3301-000233 CORE-FERRITE ZZ,18x9.5x28mm,-,- SNAFBT+H/S 6003-000122 SCREW-TAPTITE BH,+,B,M4,L12,ZPC(YEL),SWRCH18 SNAFUSE 3601-001302 FUSE-AXIAL LEAD 250V,3.15A,SLOW-BLOW,CERAMIC,5X20MM SNAIC_SOCKET 3704-001071 SOCKET-IC 42P,DIP,SN,1.778mmIC605 1204-002013 IC-DEF. PROCESSOR STV6888,DIP,32P,400MIL,PLASTIC,13.2V,-,0TO+70C,ST,100KHZL401 BH27-00131A COIL CHOKE 150UH,AN17K,150UH,10%,0.35OHM,2.5A,AR8X25,72.5TS,18X39MM,11MM,BKL402 BH27-00131A COIL CHOKE 150UH,AN17K,150UH,10%,0.35OHM,2.5A,AR8X25,72.5TS,18X39MM,11MM,BKL403 BH27-20342U COIL-CHOKE -,8.2MH(250KHz),10%,DR8*11,-,-,-,-,10.5OHM,-,-,-,BULKL601 BH29-00002A FILTER LINE NOISE AN15VS,20MH,0.42OHM,1.5KV,20MH,22X17X34MM,220V,TR,20MH,100MOHM,-10CTO+85COP201 0601-001147 LED ROUND,GRN,4.75mm,565nm SNAOP202 0604-001018 PHOTO-COUPLER DAR-TR,63-125%,200mW,DIP-4,ST SNAQ410 0505-001676 FET-SILICON IRFU230B,N,200V,7.5A,0.4OHM,2.5W,I-PAKQ411 0505-001675 FET-SILICON IRF630B,N,200V,9A,0.4OHM,72W,TO-220RL601 3501-001111 RELAY-POWER 12Vdc,250mW,5A,1FormA,15mS,5mSSH/B+AC/SK 6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNASH/B+GND 6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNASH/B+PCB 6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNASH/B+SH/LM 6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNASW601 3403-001132 SWITCH-PUSH 30VDC,0.3A,DPST,SELF LOCK,-T401 BH26-00027A TRANS-HOR.DRIVE -,-,-,-,-,-,-,-,-,-,-,PL-3,EI 1916,310uH,-,-,-T402 BH27-00137A COIL LINEARITY 7.5UH,7.5UH,DR12X15,7MM,15X15X37MM,12X9T,27TS,TR,12%,0.03OHM,USTC0.12X30T501 BH26-00140A TRANS FBT FQM15A009,AN15VS,1.95MH,SM19C,FUR3757SU,0.65 OHM,162.0,12P,-10 ~60,BK,26.0KVT601 BH26-00145A TRANS SWITCHING EER3638,AN15V,90~264V,PL-3,DMR30,EER3638,350UHT602 BH26-00141A TRANS-SYNC AR0615(L-81),AN17L,5P,200UH,200UH,1.30 OHM,L-81,AR0630, BAR,18*13*18.5,BKTH601 1404-001264 THERMISTOR-PTC 4.5OHM,+30/-20%,220V,290VAC,21A,-,TR

!

!

!

Loc. No. Code No. Description Specification Remarks

7 Electrical Parts List7-1 Main PCB Parts

TH602 1404-001020 THERMISTOR-NTC 8ohm,15%,-,17mW/C,BK

CIS9 BH97-00330G ASSY MICOM AN15VSIC201 0903-001194 IC-MICROCONTROLLER 3P863,8Bit,SDIP,42P,600MIL,12MHz,ST,CMOS,PLASTIC,5V,-,-40to+85C,1040BYTE,48KBYTECIS BH46-00005V S/W MICOM AN15VS SNA

- BH97-00351A ASSY AUTO-MAIN AN15VS SNABD401 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD402 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD403 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD406 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD410 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD411 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD601 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD602 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD603 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD605 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNAC201 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2.C202 2201-000389 C-CERAMIC,DISC 0.022nF,5%,50V,NP0,TP,5x3,5C203 2201-000389 C-CERAMIC,DISC 0.022nF,5%,50V,NP0,TP,5x3,5C204 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mmC205 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C206 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C207 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C209 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5C210 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C211 2201-000146 C-CERAMIC,DISC 0.1nF,5%,50V,SL,TP,5x3.5,5C212 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5,5C213 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5C214 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5C215 2201-000146 C-CERAMIC,DISC 0.1nF,5%,50V,SL,TP,5x3.5,5C216 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5C300 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mmC301 2301-001049 C-FILM,MPEF 150nF,5%,100V,TP,10.5x5x14.5,5C302 2305-000412 C-FILM,MPEF 470nF,5%,63V,TP,-,5mmC303 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5C304 2305-000004 C-FILM,MPEF 220nF,10%,100V,TP,12.7x16,5mmC305 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5C306 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5C307 2401-000849 C-AL 220uF,20%,35V,GP,TP,10x12.5,5C308 2301-000014 C-FILM,PEF 6.8nF,5%,100V,TP,5.8x12.5mm,5mC310 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5,5C315 2301-000519 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x3x12.5,5mC316 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C401 2401-000031 C-AL 47uF,20%,16V,GP,TP,5x11,5C402 2305-000665 C-FILM,MPEF 100nF,5%,63V,TP,7.5x4.0x5.0mm,C403 2202-000573 C-CERAMIC,MLC-RADIAL 820pF,5%,50V,NPO,TP,5.1x3.2x5.C404 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mmC405 2201-000471 C-CERAMIC,DISC 0.33nF,10%,50V,Y5P,TP,4x3.5,5C406 2301-000203 C-FILM,PEF 2.7nF,5%,100V,TP,7x3.0x6.5mm,5C407 2401-000540 C-AL 150uF,20%,63V,LZ,TP,10x25,5C408 2201-000469 C-CERAMIC,DISC 0.33nF,10%,500V,Y5P,TP,5.5x3,5C410 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5C411 2301-000005 C-FILM,PEF 33nF,5%,100V,TP,5.8x12.5x3,5C412 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm,C413 2401-001012 C-AL 3.3UF,20%,50V,BP,TP,16X25,7.5C414 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5C415 2401-001222 C-AL 4.7UF,20%,160V,WT,TP,8X11.5MM,5C416 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5C421 2303-001029 C-FILM,PPF 5.2nF,5%,630V,TP,19x7x13,7.5C426 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5

7 Electrical Parts List

7-2 AN15V*


CONFIDENTIAL

C427 2306-000131 C-FILM,MPPF 150nF,5%,250V,TP,19x16x7.5,7.5C428 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5C429 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C430 2301-001162 C-FILM,MPPF 370nF,5%,250V,TP,19x18.5x12.5,C431 2306-000179 C-FILM,MPPF 300nF,5%,250V,TP,20x18.5x10.5,C432 2305-000310 C-FILM,MPEF 22nF,5%,250V,TP,14.5x8.8mm,7.5C433 2305-001003 C-FILM,MPEF 10nF,5%,250V,TP,13x4.5x9mm,7.5C434 2201-000132 C-CERAMIC,DISC 0.1nF,10%,500V,Y5P,TP,6.5x3,5C435 2201-000229 C-CERAMIC,DISC 0.15nF,10%,2kV,Y5P,TP,6.3x5,7.5C436 2201-000672 C-CERAMIC,DISC 0.82nF,10%,500V,Y5P,TP,6.5x3,5C440 2401-001914 C-AL 1uF,20%,50V,BP,TP,5x11,5C445 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5C461 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5C462 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mmC463 2401-000597 C-AL 1uF,20%,50V,GP,TP,4x7mm,1.5mmC501 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm,C502 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5C503 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP,8x3,5C504 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5,5C505 2401-000059 C-AL 220nF,20%,50V,GP,-,5x11,5C509 2401-002267 C-AL 2.2uF,20%,250V,GP,TP,8x11.5,5C510 2301-000294 C-FILM,PEF 56nF,5%,100V,TP,9.5x12.5mm,5mmC513 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,7.5x3.5,5C541 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5mC603 2201-000024 C-CERAMIC,DISC 4.7nF,20%,250VAC,Y5U,TP,16x7,7C604 2201-000024 C-CERAMIC,DISC 4.7nF,20%,250VAC,Y5U,TP,16x7,7C605 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm,C606 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mmC607 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C609 2401-000015 C-AL 33uF,20%,50V,WT,-,6.3x11mm,2.5C610 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5C611 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5C612 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5C613 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3x5,5C614 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5C615 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,7.5x3.5,5C616 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x7,5C617 2201-000023 C-CERAMIC,DISC 2.2nF,20%,125V,Y5U,TP,11x7,5C618 2401-000039 C-AL 1000uF,20%,16V,GP,TP,10x16,5C619 2401-001585 C-AL 47uF,20%,50V,WT,TP,8x11.5,5C620 2401-000887 C-AL 220uF,20%,63V,GP,TP,10x20,5C621 2401-001585 C-AL 47uF,20%,50V,WT,TP,8x11.5,5C622 2401-000039 C-AL 1000uF,20%,16V,GP,TP,10x16,5C623 2401-000039 C-AL 1000uF,20%,16V,GP,TP,10x16,5C624 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5mC625 2301-000174 C-FILM,PEF 15nF,5%,100V,TP,7.2x4.0x7.5mm,C626 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5C628 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5C629 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C630 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5C631 2401-000292 C-AL 100uF,20%,16V,WT,TP,8x11.5mm,5C632 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5C633 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C634 2401-000480 C-AL 10uF,20%,50V,GP,TP,5x11,5C643 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5,5CIS6 0203-001199 TAPE-KRAFT #53110,T0.1,W6,L2000M,BRN SNACIS7 0203-001200 TAPE-PAPER #53128,T0.15,W5.5,L2000M,BEIGE SNACIS8 0203-001201 TAPE-PAPER #FB-300,T0.16,W6,L2000M,R/BLU SNACN501 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNACN603 3711-000217 CONNECTOR-HEADER 1WALL,3P,1R,3.96mm,STRAIGHT,SN SNAD201 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TP


AN15V* 7-3


CONFIDENTIAL

D302 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD303 0402-000128 DIODE-RECTIFIER 1N4002GP,100V,1A,DO-41,TPD401 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TPD402 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TPD403 0402-000006 DIODE-RECTIFIER 1N4007GP,1000V,1A,DO-41,TPD404 0402-000006 DIODE-RECTIFIER 1N4007GP,1000V,1A,DO-41,TPD405 0402-000208 DIODE-RECTIFIER EK-04,40V,1.5A,DO-41D407 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TPD410 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD411 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD412 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD413 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD414 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD415 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD416 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD420 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD421 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPD501 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD504 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD505 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD506 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD508 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD509 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD510 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD511 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD513 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD600 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD602 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD604 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD605 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD606 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD607 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD610 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD611 0402-001118 DIODE-RECTIFIER UF1G,400V,1.2A,DO-204AL,TPD612 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD615 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWD616 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWD625 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD626 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD627 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD628 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD629 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD630 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPEY301 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY302 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY401 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY444 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY445 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY500 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY501 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY502 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY503 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY504 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY505 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY506 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY507 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY508 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY509 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY510 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY511 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY512 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNA


7-4 AN15V*


CONFIDENTIAL

EY601 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY602 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY603 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY604 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY605 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY606 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY607 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY608 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY609 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY610 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAGT603 BH71-40300A PIN HINGE BRASS,D2.36!,HEAT/SINK,SN SNAGT604 BH71-40300A PIN HINGE BRASS,D2.36!,HEAT/SINK,SN SNAIC202 1103-001149 IC-EEPROM 524C80D41,4KBit,DIP,8P,300MIL,10mS,5V,10%,PLASTIC,-25to+70C,10uA,CMOS,STIC602 1203-000002 IC-POSI.ADJUST REG. 431,TO-92,3P,-,PLASTIC,2.44/2.IC604 1203-002653 IC-POSI.FIXED REG. 78DL05,TO-92,3P,4.5X4.5MM,PLASTIC,4.8/5.2V,625MW,-40TO+85C,150MA,-,TPJP_DHHS BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP101 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP102 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP11 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP110 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP113 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP118 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP119 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP129 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP130 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP135 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP137 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP142 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP143 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP144 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP146 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP147 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP148 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP158 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP160 2004-001211 R-METAL 7.5Kohm,1%,1/4W,AA,TP,2.4x6.4mJP162 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP163 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP171 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP175 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP176 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP179 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP180 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP183 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP184 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP186 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP187 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP193 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP194 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP195 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP196 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP197 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP198 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP199 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP2 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP20 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP200 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP201 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP202 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP204 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP205 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP206 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.


AN15V* 7-5


CONFIDENTIAL

JP207 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP208 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP209 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP21 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP210 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP211 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP212 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP213 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP214 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP215 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP216 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP217 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP219 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP220 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP221 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP25 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP3 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP30 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP32 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP33 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP34 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP35 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP36 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP37 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP4 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP43 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP56 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP57 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP58 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP60 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP62 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP64 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP8 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP9 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP91 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP94 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.MP1.0 BH41-00217A PCB MAIN AN15V*,FR1,1,1.6T,247*247,MAINQ303 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q400 0501-000372 TR-SMALL SIGNAL KSC2383-Y,NPN,900000mW,TO-92L,TP,160-320Q401 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q403 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q405 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240Q406 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240Q407 0501-000140 TR-SMALL SIGNAL 2N5551,NPN,625mW,TO-92,TP,80-250Q415 0501-000412 TR-SMALL SIGNAL KSP42,NPN,625mW,TO-92,-,40Q416 0501-000412 TR-SMALL SIGNAL KSP42,NPN,625mW,TO-92,-,40Q420 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240Q499 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240Q502 0501-000143 TR-SMALL SIGNAL 2N6520,PNP,625mW,TO-92,TP,30-200Q601 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q602 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q604 0501-000404 TR-SMALL SIGNAL KSD1616-Y,NPN,750mW,TO-92,TP,135-270Q609 0501-002228 TR-SMALL SIGNAL KTA1281,PNP,1000mW,TO-92L,TP,120-240Q610 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q613 0501-002228 TR-SMALL SIGNAL KTA1281,PNP,1000mW,TO-92L,TP,120-240Q614 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240R200 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR201 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR202 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR203 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MMR204 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM


7-6 AN15V*


CONFIDENTIAL

R205 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR206 2001-000435 R-CARBON 1MOHM,5%,1/8W,AA,TP,1.8X3.2MMR207 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR208 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR209 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR212 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MMR213 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR214 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR215 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR216 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR217 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR218 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR219 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR220 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR221 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR222 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR223 2001-000554 R-CARBON 270OHM,5%,1/8W,AA,TP,1.8X3.2MMR224 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR225 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR229 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR235 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR236 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR300 2004-001202 R-METAL 68ohm,1%,1/4W,AA,TP,2.4x6.4mmR301 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR302 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR307 2001-000908 R-CARBON 62KOHM,5%,1/8W,AA,TP,1.8X3.2MMR308 2001-001053 R-CARBON(S) 1.5OHM,5%,1/2W,AA,TP,2.4X6.4MMR309 2004-001022 R-METAL 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4mR310 2003-000422 R-METAL OXIDE(S) 1.2ohm,5%,2W,AA,TP,4x12mmR311 2004-000853 R-METAL 390ohm,1%,1/4W,AA,TP,2.4x6.4mmR312 2004-000498 R-METAL 2.7Kohm,1%,1/4W,AA,TP,2.4x6.4mR313 2001-001015 R-CARBON 9.1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR314 2001-000539 R-CARBON 24KOHM,5%,1/8W,AA,TP,1.8X3.2MMR316 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MMR317 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR327 2001-000689 R-CARBON 390KOHM,5%,1/8W,AA,TP,1.8X3.2MMR328 2001-000356 R-CARBON 150KOHM,5%,1/8W,AA,TP,1.8X3.2MMR401 2004-000979 R-METAL 47Kohm,1%,1/4W,AA,TP,2.4x6.4mmR404 2004-001022 R-METAL 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4mR405 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR406 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MMR407 2001-001099 R-CARBON(S) 2.7KOHM,5%,1/2W,AA,TP,2.4X6.4MMR408 2003-000455 R-METAL OXIDE(S) 100ohm,5%,2W,AA,TP,4x12mmR411 2001-000333 R-CARBON 12OHM,5%,1/4W,AA,TP,2.4X6.4MMR412 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR413 2001-001048 R-CARBON(S) 1.2OHM,5%,1/2W,AA,TP,2.4X6.4MMR414 2001-001048 R-CARBON(S) 1.2OHM,5%,1/2W,AA,TP,2.4X6.4MMR415 2003-000429 R-METAL OXIDE(S) 1.5Kohm,5%,2W,AA,TP,4x12mmR416 2001-000107 R-CARBON(S) 150KOHM,5%,1/2W,AA,TP,2.4X6.4MMR417 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR418 2001-000613 R-CARBON 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MMR419 2001-000397 R-CARBON 180KOHM,5%,1/8W,AA,TP,1.8X3.2MMR420 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MMR423 2004-000698 R-METAL 3.3Kohm,1%,1/4W,AA,TP,2.4x6.4mR424 2004-000412 R-METAL 18Kohm,1%,1/4W,AA,TP,2.4x6.4mmR425 2001-001178 R-CARBON(S) 680OHM,5%,1/2W,AA,TP,2.4X6.4MMR426 2001-000110 R-CARBON 10OHM,5%,1/4W,AA,TP,2.4X6.4MMR427 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR428 2003-000736 R-METAL OXIDE(S) 560ohm,5%,3W,AA,TP,6x16mmR429 2001-000773 R-CARBON 470KOHM,5%,1/8W,AA,TP,1.8X3.2MMR430 2001-001078 R-CARBON(S) 15KOHM,5%,1/2W,AA,TP,2.4X6.4MM

!

!


AN15V* 7-7


CONFIDENTIAL

R431 2003-000438 R-METAL OXIDE(S) 1.5ohm,5%,3W,AA,TP,6x16mmR432 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4MMR436 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR437 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR438 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR439 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR442 2001-000938 R-CARBON 68OHM,5%,1/8W,AA,TP,1.8X3.2MMR443 2003-000650 R-METAL OXIDE(S) 330ohm,5%,2W,AA,TP,4x12mmR445 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4MMR446 2001-000117 R-CARBON(S) 68OHM,5%,1/2W,AA,TP,2.4X6.4MMR450 2004-000262 R-METAL 120Kohm,1%,1/4W,AA,TP,2.4x6.4mR452 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR453 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR454 2003-000650 R-METAL OXIDE(S) 330ohm,5%,2W,AA,TP,4x12mmR461 2001-000010 R-CARBON 68KOHM,5%,1/8W,AA,TP,1.8X3.2MMR500 2001-000435 R-CARBON 1MOHM,5%,1/8W,AA,TP,1.8X3.2MMR501 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MMR502 2004-000861 R-METAL 39Kohm,1%,1/4W,AA,TP,2.4x6.4mmR503 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR504 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MMR505 2004-000458 R-METAL 2.2Kohm,1%,1/4W,AA,TP,2.4x6.4mR506 2004-000284 R-METAL 12Kohm,1%,1/4W,AA,TP,2.4x6.4mmR507 2004-000216 R-METAL 10Kohm,1%,1/4W,AA,TP,2.4x6.4mmR510 2001-000273 R-CARBON 100KOHM,5%,1/8W,AA,TP,1.8X3.2MMR511 2001-000478 R-CARBON 2.7OHM,5%,1/4W,AA,TP,2.4X6.4MMR514 2001-001071 R-CARBON(S) 12KOHM,5%,1/2W,AA,TP,2.4X6.4MMR515 2001-001108 R-CARBON(S) 22KOHM,5%,1/2W,AA,TP,2.4X6.4MMR516 2001-001115 R-CARBON(S) 27KOHM,5%,1/2W,AA,TP,2.4X6.4MMR520 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MMR524 2001-000337 R-CARBON 130KOHM,5%,1/8W,AA,TP,1.8X3.2MMR526 2004-000825 R-METAL 36Kohm,1%,1/4W,AB,TP,2.4x6.4mmR529 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR530 2004-000193 R-METAL 100Kohm,1%,1/4W,AA,TP,2.4x6.4mR600 2001-001129 R-CARBON(S) 330KOHM,5%,1/2W,AA,TP,2.4X6.4MMR601 2001-001129 R-CARBON(S) 330KOHM,5%,1/2W,AA,TP,2.4X6.4MMR602 2001-000023 R-CARBON 47OHM,5%,1/4W,AA,TP,2.4X6.4MMR603 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR604 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MMR605 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR606 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR607 2003-000014 R-METAL OXIDE(S) 10Kohm,5%,3W,AA,TP,6x16mmR608 2001-000034 R-CARBON 220OHM,5%,1/4W,AA,TP,2.4X6.4MMR609 2002-001068 R-COMPOSITION 180Kohm,5%,1/2W,AA,TP,3.9x9mmR610 2002-001068 R-COMPOSITION 180Kohm,5%,1/2W,AA,TP,3.9x9mmR611 2001-000018 R-CARBON 6.8OHM,5%,1/4W,AA,TP,2.4X6.4MMR612 2003-000738 R-METAL OXIDE(S) 56Kohm,5%,2W,AA,TP,4x12mmR613 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR614 2001-001107 R-CARBON(S) 220ohm,5%,1/2W,AA,TP,2.4x6.4mmR615 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4MMR616 2001-000577 R-CARBON 2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR617 2001-001048 R-CARBON(S) 1.2OHM,5%,1/2W,AA,TP,2.4X6.4MMR618 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR620 2001-000508 R-CARBON 220KOHM,5%,1/8W,AA,TP,1.8X3.2MMR621 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR622 2001-000211 R-CARBON 1OHM,5%,1/4W,AA,TP,2.4X6.4MMR623 2004-001349 R-METAL 91Kohm,1%,1/4W,AA,TP,2.4x6.4mmR624 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MMR625 2004-000481 R-METAL 2.4Kohm,1%,1/4W,AA,TP,2.4x6.4mR626 2004-000498 R-METAL 2.7Kohm,1%,1/4W,AA,TP,2.4x6.4mR630 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM

!

!

!

!

!


7-8 AN15V*


CONFIDENTIAL

R631 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4MMR632 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR634 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR663 2001-000071 R-CARBON 22KOHM,5%,1/4W,AA,TP,2.4X6.4MMR664 2001-000062 R-CARBON 470OHM,5%,1/4W,AA,TP,2.4X6.4MMR667 2001-000211 R-CARBON 1OHM,5%,1/4W,AA,TP,2.4X6.4MMR668 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR674 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR676 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4MMR677 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR678 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMSK501 4715-000001 SURGE ABSORBER 1KV,+50-10%,-,-, SNATP501 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAVR401 2103-000493 VR-SEMI 5Kohm,30%,1/10W,SIDEX201 2801-000005 CRYSTAL-UNIT 8MHz,50ppm,28-AAM,S,35ohm,TPZD201 0403-000355 DIODE-ZENER UZ5.1BSB,4.97-5.18V,500MW,DO-35,TPZD202 0403-000355 DIODE-ZENER UZ5.1BSB,4.97-5.18V,500MW,DO-35,TPZD203 0403-000355 DIODE-ZENER UZ5.1BSB,4.97-5.18V,500MW,DO-35,TPZD204 0403-000355 DIODE-ZENER UZ5.1BSB,4.97-5.18V,500MW,DO-35,TPZD205 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD206 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD207 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD208 0403-000355 DIODE-ZENER UZ5.1BSB,4.97-5.18V,500MW,DO-35,TPZD209 0403-000348 DIODE-ZENER UZ36B,36V,33-39V,500mW,DO-35,TZD210 0403-001068 DIODE-ZENER UZ4.7BSA,4.7V,4.47-4.65V,500mWZD211 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD301 0403-000355 DIODE-ZENER UZ5.1BSB,4.97-5.18V,500MW,DO-35,TP

HS601 BP96-00064A ASSY HEAT SINK P H/S POWER,SPRING,6S0765RC,RUBBER SILICONCIS 1203-002642 IC-PWM CONTROLLER FS6S0765RCB-YDTU,TO-220(FORMING),5P,9.88X9.2MM,PLASTIC,14/16V,145W,-25TO+85C,17ACIS BH61-00004A SPRING ETC-TR CDA,CDB,SUS304,-,-,-,-,-,T0.5,-,-,- SNACIS BH62-00004A HEAT SINK-POWER -,T1,-,A1050S,DA/DB SNACIS BH62-20001B TUBE-RUBBER CSQ4357,W25*L20*T0.45,-,-,-,- SNA

HS301 BP96-00065A ASSY HEAT SINK P H/S V.IC,SPRING,STV9302A,OIL SILICONCIS 0205-001027 OIL-SILICON G746,-,- SNACIS 1204-002014 IC-VERTICAL DEF. STV9302A,HEPTAWATT,7P,10.22X15.45MM,PLASTIC,35V,-,-20TO+75C,ST,-CIS BH61-00004A SPRING ETC-TR CDA,CDB,SUS304,-,-,-,-,-,T0.5,-,-,- SNACIS BH62-00003B HEAT SINK-VERT A1050S,T1.0,T1.0,-,DA,DB SNA

HS501 BP96-00066D ASSY HEAT SINK P H/S FBT,SPRING,ST2001HI,DTV1500L,KTD2058,OIL SILICONCIS 0205-001027 OIL-SILICON G746,-,- SNACIS 0402-001454 DIODE-RECTIFIER DTV1500L,1500V,4A,DO-220FP,STCIS 0502-000465 TR-POWER KTD2058,NPN,25000mW,TO-220IS,ST,100-200CIS 0502-001232 TR-POWER ST2001HI,NPN,55000MW,ISOWATT218,ST,5-10CIS BH61-00004A SPRING ETC-TR CDA,CDB,SUS304,-,-,-,-,-,T0.5,-,-,- SNACIS BH61-70003A SPRING ETC CVT4857,STS304-W1/2H,W3.8,-,L30,L30,-,T0.5,DEGRE,W3.8,STS304-W1/2H SNACIS BH62-00015A HEAT SINK-FBT A1050S,T1.0,T1.0,-,- SNA

HS402 BP96-00068A ASSY HEAT SINK P H/S TR,SPRING,IRF630B,OIL SILICONCIS 0205-001027 OIL-SILICON G746,-,- SNACIS 0505-001675 FET-SILICON IRF630B,N,200V,9A,0.4OHM,72W,TO-220CIS BH61-00004A SPRING ETC-TR CDA,CDB,SUS304,-,-,-,-,-,T0.5,-,-,- SNACIS BH62-00008A HEAT SINK-TR -,SPC-1 L20*H45*T1,-,CDB SNA


AN15V* 7-9


CONFIDENTIAL


7-10 AN15V*


CONFIDENTIAL

CIS BH94-00828A ASSY PCB VIDEO AN15VS SNA15_NOR 3704-001169 SOCKET-CRT 12P,22.5PI,-,NI+SN,-CIS BH63-00056A SHIELD-VIDEO CAP AN17KS,SPTE ,T0.2CIS BH68-00001A LABEL-MARK CDT ART-PAPER 100G,-,WHT,BLK,-,ALL,CDT SNACIS1 0202-001044 SOLDER-WIRE. S63S-W3.0,S63S,D3,63Sn/37Pb,- SNACIS11 BH39-00134A CBF-HARNESS DT15LT,3*0.16TA,BLK,AWG18,35068-9822,EARTH CLIP,BK,100MMCIS12 6502-000127 CABLE CLAMP DAWH-18NB,ID15,-,NYLON66,NTR SNACIS13 BH39-00150A CBF-HARNESS ,160MM,8*0.16TA*16CIS14 6502-000001 CABLE CLAMP DAWH-5NB,D15,L35,NYLON66,NTR SNACIS2 0202-001046 SOLDER-WIRE FLUX CF-110VH-2A,-,-,-,- SNACIS3 0202-001222 SOLDER-WIRE FLUX RS-107,RS60-1.2AA,D1.2,SN60/PB40,- SNACIS34 6502-000127 CABLE CLAMP DAWH-18NB,ID15,-,NYLON66,NTR SNACIS4 0204-001095 THINNER #4520,-,-,- SNACIS8 BH63-00055A SHIELD-VIDEO AN17KS,SPTE ,T0.2CN101 3711-004228 CONNECTOR-HEADER BOX,6P,1R,2MM,ANGLE,SN SNACN102 BH39-00015A CBF-HARNESS 13P/14P,200MM,WHT/BLK/RED/BLU,UL1007,AWG26,SMH200-13/YBNH200-14IC101 1201-001947 IC-VIDEO AMP S1D2552X04,SDIP,32P,400MIL,-,-,PLASTIC,12.6V,1W,-20TO+75C,-,-,-,-,-,STSH/VID+H/S 6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNA

- BH97-00352A ASSY AUTO-VIDEO AN15VS SNABD101 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375GBD102 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375GBD103 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375GBD104 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375GBD105 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375GBD106 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375GC102 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C103 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5C106 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C107 2401-003034 C-AL 220uF,20%,16V,WT,TP,8x11.5,5C108 2401-000049 C-AL 47uF,20%,100V,WT,TP,10x16,5C113 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm,C114 2201-000117 C-CERAMIC,DISC 1.8nF,10%,500V,Y5P,TP,8.5x3,5C115 2401-000393 C-AL 10uF,20%,100V,WT,TP,8x11.5,5C117 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm,C119 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,7.5x3.5,5C120 2201-000285 C-CERAMIC,DISC 1nF,10%,1kV,Y5P,TP,8x5,5C121 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C123 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5C124 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mmC151 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C152 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C160 2301-000203 C-FILM,PEF 2.7nF,5%,100V,TP,7x3.0x6.5mm,5C161 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5C162 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5C163 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5CB01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3CB02 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5CB03 2201-000487 C-CERAMIC,DISC 33pF,5%,50V,SL,TP,5x3,5mCB04 2401-000055 C-AL 1uF,20%,160V,WT,TP,3x11,5mmCB06 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5CB08 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5,5CG01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3CG02 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5CG03 2201-000487 C-CERAMIC,DISC 33pF,5%,50V,SL,TP,5x3,5mCG04 2401-000055 C-AL 1uF,20%,160V,WT,TP,3x11,5mmCG06 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5CG08 2201-000234 C-CERAMIC,DISC 0.15nF,5%,50V,NP0,TP,9x3,5CIS5 0203-001199 TAPE-KRAFT #53110,T0.1,W6,L2000M,BRN SNACIS6 0203-001200 TAPE-PAPER #53128,T0.15,W5.5,L2000M,BEIGE SNACR01 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3

7-2 Video PCB Parts

CR02 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5CR03 2201-000487 C-CERAMIC,DISC 33pF,5%,50V,SL,TP,5x3,5mCR04 2401-000055 C-AL 1uF,20%,160V,WT,TP,3x11,5mmCR06 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5CR08 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5,5DB01 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDB02 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDB03 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDB04 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDB05 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDG01 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDG02 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDG03 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDG04 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDG05 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDR01 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDR02 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDR03 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDR04 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDR05 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPEY1 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY2 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY3 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY4 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY5 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAG2 BH71-40300A PIN HINGE BRASS,D2.36!,HEAT/SINK,SN SNAGND BH71-40300A PIN HINGE BRASS,D2.36!,HEAT/SINK,SN SNAIC104 BH13-00022A IC HYBRID-BIAS CLAMP LM2480NA,PN15H/17L,8P,0to+70C,DIP,3mA,85V,STJP162 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP182 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP183 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP184 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP188 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP191 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP197 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP198 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP199 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP200 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP201 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP202 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP203 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP204 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP205 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP207 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP208 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.L101 2701-000112 INDUCTOR-AXIAL 100uH,10%,3x7mmL103 2701-000319 INDUCTOR-AXIAL 470NH,10%,3X7MMLB01 2701-000319 INDUCTOR-AXIAL 470NH,10%,3X7MMLG01 2701-000319 INDUCTOR-AXIAL 470NH,10%,3X7MMLR01 2701-000319 INDUCTOR-AXIAL 470NH,10%,3X7MMMP1.0 BH41-00218A PCB AN15V*,FR1,1,1.6T,247*247MM,6,VIDEOR101 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MMR102 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR103 2001-001138 R-CARBON(S) 390OHM,5%,1/2W,AA,TP,2.4X6.4MMR104 2001-001138 R-CARBON(S) 390OHM,5%,1/2W,AA,TP,2.4X6.4MMR105 2001-000947 R-CARBON 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MMR107 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR108 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MMR109 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MMR117 2001-000924 R-CARBON 680OHM,5%,1/8W,AA,TP,1.8X3.2MMR118 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MM


AN15V* 7-11


CONFIDENTIAL

R119 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MMR124 2001-001195 R-CARBON(S) 82OHM,5%,1/2W,AA,TP,2.4X6.4MMR130 2003-002282 R-METAL OXIDE(S) 39OHM,5%,1W,AF,TP,3.3X9MMRB01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MMRB02 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MMRB03 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MMRB05 2001-000702 R-CARBON 39KOHM,5%,1/8W,AA,TP,1.8X3.2MMRB07 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MMRB08 2001-000325 R-CARBON 120OHM,5%,1/8W,AA,TP,1.8X3.2MMRB09 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MMRB10 2003-002281 R-METAL OXIDE(S) 120OHM,5%,1W,AF,TP,3.3X9MMRB15 2001-000938 R-CARBON 68OHM,5%,1/8W,AA,TP,1.8X3.2MMRG01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MMRG02 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MMRG03 2001-000857 R-CARBON 560OHM,5%,1/8W,AA,TP,1.8X3.2MMRG05 2001-000702 R-CARBON 39KOHM,5%,1/8W,AA,TP,1.8X3.2MMRG07 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MMRG08 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMRG09 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MMRG10 2001-001077 R-CARBON(S) 150OHM,5%,1/2W,AA,TP,2.4X6.4MMRG15 2001-000938 R-CARBON 68OHM,5%,1/8W,AA,TP,1.8X3.2MMRR01 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MMRR02 2001-000969 R-CARBON 75OHM,5%,1/8W,AA,TP,1.8X3.2MMRR03 2001-000780 R-CARBON 470OHM,5%,1/8W,AA,TP,1.8X3.2MMRR05 2001-000702 R-CARBON 39KOHM,5%,1/8W,AA,TP,1.8X3.2MMRR07 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MMRR08 2001-000376 R-CARBON 15OHM,5%,1/8W,AA,TP,1.8X3.2MMRR09 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MMRR10 2003-002281 R-METAL OXIDE(S) 120OHM,5%,1W,AF,TP,3.3X9MMRR15 2001-000938 R-CARBON 68OHM,5%,1/8W,AA,TP,1.8X3.2MMSK101 1405-001064 SURGE ABSORBER 400V,20%,-,-,AXIALSK102 4715-000001 SURGE ABSORBER 1KV,+50-10%,-,-, SNASKB01 4715-000102 SURGE ABSORBER 200V,20%,1000A,-,RADIAL SNASKG01 4715-001065 SURGE ABSORBER 200V,20%,-,-,AXIALSKR01 4715-000102 SURGE ABSORBER 200V,20%,1000A,-,RADIAL SNAZD101 0403-000355 DIODE-ZENER UZ5.1BSB,4.97-5.18V,500MW,DO-35,TP

HS103 BP96-00063B ASSY HEAT SINK P H/S VIDEO,SCREW+NUT,STV9555,OIL SILICONCIS 0205-001027 OIL-SILICON G746,-,- SNACIS 1201-001917 IC-VIDEO AMP STV9555,CLIPWATT,11P,20X11MM,TRIPLE,20DB,PLASTIC,115V,4.79W,-,-,-,-,-,-,STCIS 6006-001009 SCREW-ASS’Y MACH WSP,BH,+,M3(WOD6),L12,ZPC(YEL) SNACIS 6021-000118 NUT-HEXAGON 1C,M3,ZPC(YEL),SM20C SNACIS BH62-00006A HEAT SINK-VIDEO -,A1050S T2.0,-,DB SNA


7-12 AN15V*


CONFIDENTIAL

- BH90-00257A ASSY STAND PN17HT,ABS HB,IV16,W/W SNACIS BH75-00274A UNIT-STAND PN15VT,-,ABS HB,-,IV16,-,-CIS BH60-00030A FASTENER-BAND PN17LT,ST+PVC,P0.4,-,150,YELLOW,-,-,- SNACIS BH61-40002A FOOT-RUBBER -,NR,PMS428U,GA4237,-,-,- SNACIS BH63-30103A FELT-STAND MCM1755,FELT,T1.0,W10,L4CIS BH68-20366A LABEL-MARK STAND -,ART PAPER 100(S),-,-,-,-,-,WHT ,-,- SNACIS BH68-70306A CARD-STAND CVM4967PWS(SKD),WONSTROW,CHAIN SNACIS BH69-30348C BAG-PE HDPE,T0.02,W350*L430,Y,-,CGB51 SNACIS BH72-00277A STAND TOP PN15VT,ABS,HB,IV16 SNACIS BH72-60740A STAND BASE-USB CHB5807,ABS,HB,IV16 SNA

- BH90-00348A ASSY COVER FRONT AQ15VS,ABS V0,IV16 SNAC/F+C/R 6003-000009 SCREW-TAPTITE BH,+,B,M4,L16,ZPC(YEL),SWRCH18 SNAC/F+CDT 6006-001119 SCREW-ASS’Y TAPT WC,BH,+,M5,L25,ZPC(YEL),SWRCH18A SNACIS BH90-00002A ASSY COVER FRONT AQ15VS,-,ABS V0,-,IV16,-,-,-CIS 6107-001036 SPRING-CS PI9.4,D0.6,L15,WHT,STS304WPB SNACIS BH59-00182A PBA SUB-FUNCTION PN17HT,DB-PN17HT,SAMSUNG,-,FUNCTION,-,- SNAD3 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWR231 2001-000241 R-CARBON 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MMR233 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MMR234 2001-000563 R-CARBON 27KOHM,5%,1/8W,AA,TP,1.8X3.2MMR232 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MMSW201 3404-000243 SWITCH-TACT 15V,20mA,160gf+-50gf,6x3.4mm,SSW202 3404-000243 SWITCH-TACT 15V,20mA,160gf+-50gf,6x3.4mm,SSW203 3404-000243 SWITCH-TACT 15V,20mA,160gf+-50gf,6x3.4mm,SSW204 3404-000243 SWITCH-TACT 15V,20mA,160gf+-50gf,6x3.4mm,SCN2 BH39-00255A CBF HARNESS PN17HT,UL1007#26,UL/CSA,2P,150MM,BLU/WHT,AWG26,SMH250-02,60-9073-3018-02CIS BH41-00117A PCB CONTROL PN17HT,FR-1,1 LAYER,00,1.6t,13*84,PN17HT,-,CONTROL,CONTROL BOARD SNACIS BH64-00096A KNOB-FUNCTION AQ17LS,ABS,HB,IV16 SNACIS BH64-00133A KNOB POWER AQ15VS,ABS ,HB,IV16 SNACIS BH67-00018A LENS-LED PN15VT,ACRYL ,CLEAR,-,-,-,- SNACIS BH71-00121A EARTH PLATE PN17LT,SUS304,T0.15 SNACIS BH72-00334A COVER FRONT AQ15VS,ABS,V0,IV16 SNA

- BH90-00349A ASSY COVER REAR AQ15VS,ABS V0,IV16 SNACIS BH72-00335A COVER REAR AQ15VS,ABS,V0,IV16

- BH91-00793C ASSY CDT AN15VS SNA- BH91-00793S ASSY CDT-TM TM-AQ15VS SNA

CIS 0201-001052 ADHESIVE-CYA NO2/TOKYO/3BCO,WHT,-,- SNACIS 0203-000005 TAPE-ACETATE SGT730,T0.26,W19,L3000,BLK SNACIS 3302-000006 MAGNET-RUBBER AF,14G,1620-1980G,0.58-0.9MGOe SNACIS 3309-000002 MAGNET-SHEET 5x20x80mm,UL94V-0,2 SNACIS 6502-001019 CABLE CLAMP DAMC-10,ID9.9,T7.1,NYLON6.6,GRAY SNACIS BH03-10014A CDT-SN M36KUM35X02,-,15,0.28,-,MS-GUN,-,-,-,-,-,VLMF,4CIS BH03-00006C CDT M36LGE23X211(F6M1),54,15,0.28,-,22.5,FST,N/C,NH,EQ,-,ESF,NONE,4CIS BH68-30003B LABEL-HIGH VOLTAGE CKA4217(C),ART,100G,YEL,BLK,W30*L30,CDT-TUBE SNA

CIS BH96-00114A ASSY D-COIL P 15INCH,BH27-00129A,BH39-00413A

- BH91-00802C ASSY CHASSIS AN15VS

- BH92-00519B ASSY P/MATERIAL AQ15VSPN/XAZ,SEDA,BRAZIL SNAP/MATERIAL 0203-001100 TAPE-OPP MASKING OPP/W75/CLR,T0.05,W75,L800000,CLR SNAP/MATERIAL 0203-001159 TAPE-FILAMENT #8915,T0.15,W12,L55000,CLR SNAP/MATERIAL BH69-00260A BAG AIR DP17L,PE,0.2,1800,1000,NATURAL,- SNAP/MATERIAL BH69-00362A CUSHION-L/R(S) AQ15VS,EPS M50,-,-,-,-,-,-,- SNAP/MATERIAL BH69-30002C BAG-PE LDPE,T0.05,W2400,NO_PRINT SNAP/MATERIAL BH69-30348A BAG-PE HDPE,T0.02,W850*L800,Y,-,CGB51 SNAP/MATERIAL BH69-30360A BAG-AIR HDPE,T0.2,W1000*L1800,N,-,ALL SNAP/MATERIAL BH69-40380A PACKING-PAD DW-2,500X2200X200,-,CGK5527 SNA


AN15V* 7-13


CONFIDENTIAL7-3 Others

- BH92-00876A ASSY BOX AN15VS SNACIS BH68-00329A LABEL BAR CODE ALL,MPRII,DOM,EXPORT,ART-PAPER 90G,-,-,-,-,-,WHT,-,- SNACIS BH69-00384A BOX S/M551S,W/W(SMALL),CB-SW4,YEL,A-1,-,-,-,L466*W445*H366,- SNA

- BH92-00877A ASSY LABEL AN15VS SNALABEL BH68-00459B LABEL RATING B,PE,T0.05,109,50,SYNC,-,PE NATURE,-,- SNA

- BH92-00878A ASSY ACCESSORY AN15VS SNAUNIT/ACCESSORY BH96-00117A ASSY ACCESSORY AN15VS7L/EDCACCESSORY 0203-000214 TAPE-OPP MASKING OPP/W50/CLR,T0.05,W50,L400000, SNAACCESSORY BH39-10007A CBF POWER CORD DET,250V/6A,H05VV-F,LP-34A/KKPACCESSORY BH59-00335A S/W DRIVER-00 AN15VS,IB/DRIVER,SYNCMASTER,E/F/S/G/P/I/R/H/PO..ACCESSORY BH68-00374A CARD WARRANTY ASC List,Samsung,ART100G,Russian,EDC,295,210 SNAACCESSORY BH68-00376J MANUAL AN_QUICK SETUP GUIDE,SYNCMASTER,E/F/S/G/P/I..14LANGS,W/W,MOJO100G,298,420ACCESSORY BH68-00489A MANUAL RUSSIAN W/CARD,SER,RUSSIAN,RUSSIA,MOJO100G SNAACCESSORY BH68-70418A CARD-EU BLOC WARR SyncMaster,BASIC,EU,MOJO,100G, SNAACCESSORY BH69-30348D BAG-PE LDPE,T0.05,W240*L356,Y,-,CMG73 SNA- TM-AN15VS 2 TSB,MINI-NECK -


7-14 AN15V*


CONFIDENTIAL

8 Block Diagrams

AN15V* 8-1

CONFIDENTIAL

Memo

8 Block Diagrams

8-2 AN15V*

CONFIDENTIAL

CONFIDENTIAL

AN15V* 9-1

15 PIND-SUB

refer to pinassignment

ofproduct spec.

9 Wiring Diagram

Memo

9 Wiring Diagrams

9-2 AN15V*

CONFIDENTIAL

AN15V* 10-1

OFF_1

50V

C2051uF

EY610EYE1.5

1

KTA1281-YQ609

B

C

E

13V_1

1001/6W

R220

B

C

E

100K

1/4WMF

R530

SNAME

CN501

1

EMT

70V

R678

C436820PF500V

EYE2.2EY502

R432

1/2W

2N6520Q502

C602

150nF

56 1/8W

V_REG

H_DRV

EW_OUT

B_DRV

B_SENSE

V_BLK

ADJ_ACL

DY_H4

DY_V1

V_OUT

DY_V2

GND

GND

CLAMP

150uH

GND

VCAP

HPOS

HIGHLOW

PLL1F

HIGH

RESET

DEGAUSS

3W

SDA

TEST

S-Correction Table

ISENSE

SUB_SIZE

DDCDATA

S2

KEY1

VSYNC_IN

VGND

LOW LOW

ADJ_ACL

C0

FC1VCC

31 ~ 34.9

F/S Test Point

---------

HIGH

HEHT

MODE_SIZE

HIGH

S3

IIC_CLK

SIZE-ADJ

H-DY

LATCH

PLL2C

REGIN

R0

COMP

DDCCLK

NC

HSYNC_OUTVRB

VOUT

POWER_KEY

HVFOCUS

SCREEN

OFF_1

1.2UH

AC INPUT

LOW

VEHT

Freq [Hz] S1

D-C

OIL

L : NORMAL

MODEL-SEL

NC

H/V

1.2UH

8MHz

HSYNC

VAGCVSYNC_OUT

1.2UH

SCL

Option

AVREF

L : OFF MODE

1.2UH

S1

HREFX-IN

35 ~ 39.9

40 ~ 48.9

49 ~

IIC_DATA

TILT

5V

TSB CDT

MUR460

KEY2

S2

NC

LED

KEY3

FOCUS

VFOCUS

M

XRAY

HOUT

VSYNC

V-DY

MODE_REG

120uH

H : NORMAL

EWOUT

HSYNC_IN

STV6888

HUNLOCK

BOUT

X-OUT

AC90V~AC264V

SELFRASTER

OFF-MODE

OUT

NC

HGND

H : OFF MODE

HFLY

CC

IC604S78DL05

GND

IN

R620

1/2W180K

R610

100V

C41222nF

P

220K1/6W

2

34 5

678

KS24C041-C

IC202

1

10K1/8W

D502RGP02-12(T)

1

2

3

6

5

4

R603

500V

T402

SUPLECODE

C63410uF

C515

330pF

1/6W

R203

15K

50V

BH62-00004AHS601

R314

1/6W

R313

9.1K

R509

1/6W

24K

56 1/8W

12V

1/2W

330K

EY609

EYE1.51

R207

500V

1nFC615

R508

1N4148

D415

R513

1/2W

330K

1KV10nF

C512

1/2W47K

R510100K

1/8W

C516

330pF500V

1/6W

R523180K1/2W

KSC945-YQ401

B

C

E

R327390K

OT

1.6KV2.2nFC418

R443

3302W

MOE

slcon4pCN404

1

2

3

4

2N5551C-Y

Q407

B

C

MO

R415

2W

1.5K

R300

C517

330pF500V

1N4148D629

MF

1/4W68

C6221000uF

16V

R3165.6K

1/6W

D511

1N4148

50V

C410100uF

16V

MF

D607

1N4148

50V

220nF

R62391K

1/4W

1K1/2W

C505

UZ5.1BSB

ZD203

R676

RGP02-12(T)D512

ZD301

UZ5.1BSB

D

GS

EY6061

1/2W1.5

IRF630BQ410

KSC945-YQ602

B

C

E

R308

22pF50V

C203

HS402

C603

250V

4.70NF

1K1/8W

R4362.2K

1/8W

P

R427

C514

330pF500V

100V

6.80NFC308

C407150uF63V

Q415KSP42

B

C

E

R6162K

1/8W

BD601

B

C617

1N4148

D630

DRAIN1

F_B4

GND2

SYNC53

Vcc

125V2.2nF

B

C

E

IC601DP104C

47UF

50V

22

2.7

1/4W

C621

SHL

P

100V2.2nFC541

R511

22K1/6W

R406

R213 10K 1/8W

C620

63V220uF

C604

C504

1nF50V

1/4W

47

4.70NF

250V

1uF

R602

D6261N4148

50VC611

KSA733-YQ405

B

C

E

1SS244D421

R522330K

1/2W

1/8W

10KR634

R674

1/8W10K

1.21/2W

50V1uFC612

50V

1nFC310

R617

1N4148D513

1/8W

130KR524

500V

10nFC614

R605

4.7K1/8W

IC602

TL431CLP

A

K

R

P

100V2.7nF

C406

150K1/6W

EK-04

D405

R604

R328

1N4002GPD303

1.5K1/8W

Q613

KTA1281-YB

C

E

5V

1/8W10K

EYE1.5

EY508 1

2

3

5

4

R235

BH26-30302S

T602

1

1N4148

D416

D625

1N4148

P100V

10nFC404

D408

DTV56F

6.3V

1N4007GPD403

-140V

1M1/6W

R206

16V

47uFC303

HS301BH62-00003A

1K 1/8WR214

UZ36BZD209D3021N4148

TH601

D413TVR10G

4.7uF

50V

C216

1/6W100R302

CN502

slcon3p

1 2 3

6.3V

MP

63V

470nF

C302

1/6W47K

R317

1

12K1/4WMF

R506

IC300

1 2 3 4 5 6 7

EY301

D

GS

TDA9302H

6.8K

Q402

IRF630

5Kohm

R501

1/6W

1

1/4W

VR401

2.2K 1/8W

R622

16V

10uFC502

13V_1

R405

250VMP

12V

10uF50V

C43222nF

D420

1N4148

C445

C606

P100V

10nF

B

MPS

250V

C409680NF

C

E

12V

BFS3557AOLS1

BD406

180uF400V

Q420KSA733-Y

B

P100V

2.2nFC624

C608

1K1/8W

BD401

B

R677

B

1/6W

R30762K

R500

BD402

5V

1M1/6W

22K

1/2W

R515

R43015K1/2W

ZD205

UZ6.2BSB

EY401

1

R20110K

1/8W

R419180K1/6W

C307220UF

35V

R311

BD603

B

1/4W22K

1/4W

MF

390

C

E

R663

D404

12V

Q404KSC5802D610

1N4007GP

UZ5.1BSB

ZD202

UF4007(T)

R218

1/6W100

R309

MF1/4W

5.6K

25

26

R217

1/6W100

16

42

17

18

19

20

21 22

23

24

37

12

38

13

39

14

40

15

41

32

7

33

8

349

35

10

36

11

27

2

28

3

29

4

30

5

31

6

1N4148D602

IC201

KS88C6232N

1

MO

2W330

MP63V

100nFC402

R454

50V

C215

C610

16V

100uF

100pF

R219

1/8W10K

R618

1K1/8W

EYE2.21

C405330pF50V

1K

1/8W

R606

EY601

C462

10nF 100V P

50V1nF

C643

1/4W MFR502

39K

EYE1.5EY505 1

12V

C

E

C427

150nF250V

MPS

Q499

KSA733-YB

KSP42Q416

1/2W1K

R631

C2121nF

50V

C403820pF

50VMO

HS501BH62-00002A

470nF

C414

L403

7.1MH

50V

1/2W

C463

1uF 50V

12V

R4072.7K

12V

5V

C6162.2nF125V

R520

1/6W22K

220UFC201

16V

13

14

15

D609

31DF4

2

3

4

5

6

7 8

9

10

11

12

1N4148

D506

HFL1327XD-RC

T501_1

1

1000uF

C618

100nF50V

MO

16V

12K1/2WR514

C316

KSC945-YQ403 B

C

E

500V10nFC632

1

ZD208

UZ5.1BSB

100V

C3153.3nF

P

7

1/8W10KR209

CN202slcon7p

1

2

3

4

5

6

R408

MO

2W100

13V_2

R204

1/6W15K

R417

1/8W10K

R600

330K1/2W

13V

P

100V33nFC411

100V

1/6W

R4183.9K

B

C

E

P

C510

56nF

150nF

C601

Q303

KSC945-Y

R461

275VAC

1/6W

6.3V_1

1/6W68K

50V47UFC619

R202

10K

EYE1.5EY608

1

1N4148D501

Q614

KSC945-Y

B

C

E

3 4

50V1uF

C426

D601D2SBA60

12

EYE1.51

13V_1

1/6W

100

R229

D412

TVR10G

EY507

UF4007D605

36KR526

MF

1/4W

27K

1/2W

R516

13V

50V100pF

C211

R50415K

1/6W

MP250V

10nFC433

D411

1N4148

1N4148

D410

5.6K

1/4W

MF

R404

R608220

1/4W

160V4.70UF

C415

D504

UF1GD611

2201/2W

TVR10G

EY6051

R614

GT603

1

4

13V_1

1/4W1R667

L601

1 2

3

R215 1/6W100

B

C613220pF

1KV

BD410

BFS3557AOLS1

1001/6W

R601

1/2W

330KB

OP202LTV817M-SM

ANODE

CATHODE

COL

EY445

EYE1.51

1.2UH

BD600

3

-10V

BFS3557AOLS1BD605

B

-10V

SW601

JPS1275

1 2

12

13

16V

100UFC626

2

3

4

5

6

7

8

9

10

11

slcon13p

CN201

1

B

C E

2.4K1/4W

MF

R625

470UF

KSD1616-Y

Q604

4701/4W

C306

16V

C300

10NF100VP

R664

MPS250V

300nF

MO50V

100nFC607

C431

C206100nF

50VMO

150K1/4W

R420

R425

1/2W680

3

4

7

6

5

C435

150PF2KV

EI-1916T401

1

2

1/2W

1KR615

R429

1/6W

470K

R6132K

1/8W

C20410nF100V

P

PP

630V5.2nF

C421

12V

UZ5.1BSB

ZD201

EYE2.2

EY603 1

R507

10K

1/4WMF

ZD206

UZ6.2BSB

EYE1.51

R612

MO2W

56K

EY509EYE1.5

1

EY512

ERD07-15D406

FUSE2P

FH_1

L402

R503

10K1/8W

C202

22pF50V

EYE2.21

500V100PFC434

GUR460L-5700

D409

70V

EY604

R312

MF1/4W2.7K

1/2W

R44668

D628

1N4148

10K

R453

100 1/6WR216

MO3W

EY602EYE2.2

1

R428560

D414

1N4148

CN603slcon3p

1

2

3

50V

100nFC416

P100V

12V

7V

OP201LTL-10233W

370nF

250VP

C430

C600

1nF400V

R445

C4133.3UF50V

G5PA-1RL601

12

3

4

10

1/2W

EYE1.5

EY607

1

4.7K1/8W

R222

1/8W56R208

50V4.7uF

C209

470UF16V

C305

UF5404D608

R450120K

1/4WMF

50V

UZ6.2BSB

D618

EY511 1

47K1/4WMF

R401

EYE1.5

D615

UZ6.2BSB

1N4148D201

50V

1uFC207

R236

10K1/8W

P

100V

150nF

C301

OSD_5V

1K1/8W

R412

14

2

9

C631100uF16V

18

19

25

22

24

10

13

12

23

21

31

27

29

8

1

26

30

28

15

17

7

IC605

20

6

5

3

4

16

11

32

P

100V15nF

C625

D616UZ6.2BSB

C

E

P100V

22nFC605

Q408KTD2058-Y

B

R62110K

1/8W

101/4W

330pF

500V

C408

R426

D5091N4148

1N4148

D627

9

18

17

16

15

14

13

12

11

10

1

2

3

4

5

6

7

8

MF

1/4W3.3K

EER39*42mm

T601

1N4148D510

R423

R611

6.81/4W

ZD207

UZ6.2BSB

L401

C629

50VMO

100nF

FUSE

10K 1/8WR205

2W

1.2

MO

R310

R452

10K

R200 1/8W56

X201

Q0

Q1

R668 1K 1/8W

275VAC

UZ6.2BSBZD211

C628

10nF500V

22nF

C501

C503100nF

50V

1N4148D505

P100V

2.2K

1/4W

MF

R505

OSD_5V

R411

1/4W12

IRF630BQ411

D

GS

1N4148

D600R439

D612TVR10G

R416150K

1/2W

47K1/6W

BD403BFS3557AOLS1

B

1/8W3.3K

R212

16V47uFC401

C513

1nF

C633

1uF50V

UZ4.7BSAZD210

500V

50V4.7uF

C461

47K

1/6W

R437

CN601slcon3p

1 2 3

R223

FH1

1/6W270

50V10uF

C428

C609

33uF50V

TP501 1

50V

1.5

MO

R431

S-23(1KV),5MMSK501

1

12V

R630

1/6W47K

EY500EYE1.5

1/8W33KR480

D402UF4004

1/6W22K

R481

KSA733-Y

Q406

B

C

E

1.21/2W

TVR10GD606

R632

R413

BD602

1.2UH

B

1/8W10K

2.7K1/4W

MF

R626

T502EE-1916

1 4

8 6 5

C440

1uF50V

R225

ZD204

UZ5.1BSB

1/8W

1KR529

MP100V220nFC304

1

2

R221

1/8W4.7K

slcon2pCN604

GT604

1

UF4004D401

KSC945-YQ610

B

C

E

13V_2

C

E

1N4148D508

1

KSC2383-YQ400

B

50V1uF

C429

EYE1.5EY504

5V

EY444EYE1.5

1

1/6W

68R442

TH602

7V

12V

180K1/2W

CC

R609

SCK-083 C630470uF

16V

6.8K1/6W

P100V

100nFC213 C214

100uF

16V

R624

1/8W

2.2KR438

B

C

E

C623

16V1000uF

Q601KSC945-Y

EYE2.2

EY5031

EYE2.2EY5011

D604

UF4007

R4141.2

1/2W

5V

1N4148D624

1

UF4004D407

R301

EY510

EYE1.5

4.7K 1/8W

BFS3557AOLS1

BD411

B

C2101uF

50V

MO3W10K

R607

P2.5KV

4.4nFC419

1/6W

10KR470

18K1/4W

MF

R424

250V2.2uF

C509

EY302 1

50V

EYE1.5EY506 1

R224 1/8W56

VREF

VREF

DY_H3

50V_SENSE

SIZE_REG

S3

S3

TILT

DY_H4

OFF_2

AFC

ACL

OFF_1

V_MUTE

MODE_SIZE

SIZE_ADJ

MODE_REG

DEGAUSS

S2

S1

OFF_2

S_RASTER

DDCCLK

DDCDATA

50V_SENSE

HS_IN

B_DRV

AFCVS_IN

VS_OUT

B_SENSE

HS_OUT

ADJ_ACL

MODE_REG

S1S2MODE_SIZE

SIZE_REG

SIZE_ADJ

EW_OUT

DEGAUSS

H_DRV

DY_V1

DY_V2

DY_H3

S_RASTER

DDCCLK

DDCDATA

VS_IN

HS_IN

IICCLK

IICDATA

V_MUTE

V_BLK

G1

VS_OUT

G1IICDATA

ACLIICCLK

HS_OUT

AFC

HS_OUT

VS_OUTIICDATA

V_REG

IICCLK

AFCIICDATA

IICCLK

V_OUT17

9

22

1110

13

12

6

5

3

4

7

8

1 2

10 Schematic Diagrams

10-1 Main Part Schematic Diagram

CONFIDENTIAL

CONFIDENTIAL10 Schematic Diagrams

10-2 AN15V*

12 50.0 V (T502, #6)

CH1 P-P = 50.0 V CH1 RMS = 75.6 V

13 100 V (T502, #1)

CH1 P-P = 100V CH1 RMS = 124.0 V

1 100 V (IC601, #1)

CH1 P-P = 100 V CH1 RMS = 350.2 V

2 100 V (IC601, #1)

CH1 P-P = 100 V CH1 RMS = 325.8 V

3 5.00 V (IC605, #28) 4 1.00 V (IC605, #26) 5 5.00 V (Q400, Collector) 6 5.00 V (Q408, Collector)

7 1.00 V (IC605, #24) 8 1.00 V (IC605, #23) 9 10.0 V (IC300, #6) 10 5.00 V (Q402, Gate)

CH1 P-P = 2.00 V CH1 RMS = 7.692V

11 50.0 V (Q402, Drain)

CH1 P-P = 50.0 V CH1 RMS = 73.7V

17 2.00 V (IC201, #13, 14) 22 5.00 V (Q502, Collector)


AN15V* 10-3

10-2 AN15VS Normal Video Part Schematic Diagram

SDA

TDA9555

120 OHM

CLP_IN

CLAMP

BCLP

VCO_IN_P

GOUT

AC

L

RIN

GCT

V_SYNC

VCC2

ABL_IN

VSS

GND1

GND

AF

C

RCT

VREF1

IICDATA

G1

GIN

VFLB

KB2551

VSSA

120 OHM

ACL

VDDA

VREF

IICCLK

VCC1

CONT_CAP

GND2

VDD

GCLP

SCL

IICC

LK

VS

_OU

T

IICD

ATA

RCLP

BCT

ROUT

HFLB

BIN

CLA

MP

BOUT

VCC3

CG06100nF100V

1K 1/8W

1/8W3.3KR101

50V100nFC152

12V

R107

MO

1uFCB02

CG08150PF50V

CG04

160V1uF

50V

6RED

WSP-401MSK101

9BLUE

3G

1G

25

GN

D1

GN

D1

7 10G

ND

2

GREEN4

8H

EA

TE

RO

PE

N2

15_NORcrt_sock10p

R1195601/8W

G21

LB010.47uH

CR081NF50V

5V

CR02

50V1uF

1

1/2W390R103

100V100nFCR06

EY2

RR03470

100V100nFCB06

1/6W

1920212223242526

70V

89

10111213141516 17

18

2

28

329

4

30

5

31

6

32

7

IC101

1

27

C106100nF50VMO

1/4W

RG0975K

C118

50V1uFC162

BD104

B

100pF50V

SKG01SPARK_RA

100nFCG01

1/6W

75RG02

RB15

MO

50V

P100V

1/6W68

RR01

1/6W75

22NFC113

1UF

EY51

50V

CG02

560RB03

100nF50V

MO

6.3V

1/8W

C151

BD1011.2UH,3.5*5.7MM

B

CB01

10 11 12 13 14

MO50V100nF

1 2 3 4 5 6 7 8 9

6801/6W

slcon14pCN102

39K

R117

CN101slcon6p

1

2

3

4

5

6

RR05

HS103heat_sink

1SS244DB04

P100V10nFC124

0.47uHLG01

MO50V100nFC121

5V

1/4W75K

C11510UF100V

12V

RB0916V100UFC161

1/6W68RR15

L1030.47uH

EY41

500V1nFC119

DR011N4148

12V

16V470uFC103

CG0333PF50V

RG081/6W 100

6.3V

RB081201/6W

1

POW

RR10

DB05

1N4148

EY3

CB081NF50V

70V

1

1.2UH,3.5*5.7MMBD106

B

GND

1/6W

R109

C16047uF16V DB03

12_1V

70V

12K

SKB01

DMS-200D

1SS244

RG01DG021N4148 1/6W

75

100V47uF

C108

1/6W100R102

CR01100nF50V

MO

1SS244DR03

DMS-200D

SKR01

SK102

7.5KR105

C16310NF500V

1/6W

RG15681/6W

18K

1N4148DG01

DR021N4148

RG07

39KRB05

18K

C107220uF

16V

RB07RR0718K

R124

821/2W

RG10

1/2W150

75

1/6W

RB02

1SS244DR04

1.2UH,3.5*5.7MM

B

L101

100uH

BD102

DZ5.1BZD101

RB01751/6W

1N4148

12V

DB01

1SS244DG04

LR010.47uH

39KRG05

DB021N4148

560

1/8W

RG03

EY11

C12310nF500V

DG031SS244

UZ6.2BSBZD102

DG051N4148

MO1W39ohmR130

R1043901/2W

CB041uF160V

12V

M36KUK35X02(R)CRT1/6W

5.6K

C1021uF50V

D5

E

6F

7G

8H

R108

LM2480NAIC104

1A

2B

3C

4

R120

DR051N4148

RB10

1/4W30M

POW

500V

151/6WRR08

1.2UH,3.5X5.7MMBD103

B

1.8nFC114

75

1/6W

RR02

B

G1

1KV1nFC120

7V

DD

G1

BD105

5G

ND

A

8G

ND

P

6G

ND

S

1IN

1

2IN

2

4IN

3

11O

UT

1

10O

UT

2

9O

UT

3

3V

CC

TDA9556

IC103

C117

CR04

1uF160V

1/4W

75K

22NF100V

P

R118

RR09

50V33PFCB03

1/8W560

50V33PFCR03

B_OUT

G_OUT

R_OUT

G2

AFC

1515 2020

1919

1414

1616

2121

2323


10-4 AN15V*

14 1.00 V (IC101 #12,14,16) 15 0.5 V (IC101 #18,21,24) 16 20.0 V (IC102 #9,10,11) 19 2.00 V (IC101 #1)

20 1.00 V (IC101 #18,21,24) 23 50.00 V (CRT Socket, G1)21 10.0 V (R,G,B, Video)

CH1 P-P = 10.0V CH1 RMS = 17.02V


AN15V* 10-5

GND2

VCC2

VS

_OU

T

GIN

VFLB

CLP_IN

CONT_CAP

GND

VCO_IN_P

G1

IICCLK

VREF1

RCT

VDD

SDA

SCL

BIN

CLA

MP

IICDATA

V_SYNC

BOUTA

FC

VCC3

RIN

ROUT

BCLP

BCT

VDDA

VSS

IICD

ATA

CLAMP

VREF

GND1

GOUT

VCC1

GCT

HFLB

ABL_IN

IICC

LK

KB2551

AC

L

ACL

VSSA

120 OHM

120 OHMRCLP

GCLP

C117

1/6WRR08

22NF100V

P

BD1021.2UH,3.5*5.7MM

B

15

1

C106100nF50VMO

DB05

1N4148

GND

DB021N4148

C1021uF50V

RG01

R108

1/6W5.6K

1/6W75

R120

6.3V

RG081/6W 100

100V100nFCB06

1/4W30M

6

RG0718K

CG06100nF100V

CN101slcon6p

1

2

3

4

5

1/6W68RR15

1/6W

75RG02

12V

12V

POW

RB10

B

100V100nFCR06

BD1011.2UH,3.5X5.7MM

B

BD104

P

12V

50V1uFC162

C1602.7nF100V

RB0718K

MO50V100nFC152

RG15681/6W

1/8W

560RB03

1/6W

RR03470

1K 1/8W

CR081NF50V

70V

R107

RR02

CB041uF160V

1/4W75K

75

1/6W

1

L1030.47uH

RB09

BD103

B

EY4

DZ5.1BZD101

1.2UH,3.5X5.7MM

RR09

1/4W

75K

751/6W

DG051N4148

RB01

R1043901/2W

R1176801/6W

16V470uFC103

6.3V

RR01

1/6W75

75

1/6W

RB02

DB04

DR051N4148

M36KUK35X02(R)CRT

1SS244

CG04

160V1uF

G1

CR041uF160V

C121

G1

1SS244DG04

MO50V100nF

CR01100nF50VMO

5601/8W

SKR01SPARK_RA

R124

821/2W

R119

BK1

4

G1G2

6

7 GK

3

GND1

8

GND2

2

H

RK5

SPARK_RASKG01

15_MINIj_c8_1p

12 13 14

EY51

2 3 4 5 6 7 8 9 10 11

slcon14pCN102

1

50V1uFCB02

C107220UF

16V

1N4148 CB01100nF50V

MO

C16310NF500V

DG02

VD

D

BD105

B

5G

ND

A

8G

ND

P

6G

ND

S

1IN

1

2IN

2

4IN

3

11O

UT

1

10O

UT

2

9O

UT

3

3V

CC

7

TDA9556IC103

12V

12K

1/6W

R109

1/8W560R118

0.47uH

100V47uF

C108

39KRB05

LB01

26

5V

1SS244DB03

1516 17

1819202122232425

31

6

32

789

1011121314

1

27

2

28

3294

30

5

IC101

1.2UH,3.5*5.7MMBD106

B

16V100UFC161

HS103heat_sink

LG01

500V1nFC119

P100V10nFC124

0.47uH

12_1V

1SS244DR03

MO

50V100nFCG01

RB081201/6W

RR10

CG08150PF50V

SK102

POW

39KRG05

50V

CG021UF

1/6W100R102

75K

DB011N4148

1/4W

RG09

DG01

12V

C12310nF500V

1SS244

1N4148

1/8W3.3KR101

DG03

CB081NF50V

C11510UF100V

LR010.47uH

100uH

ZD102UZ6.2BSB

39K

L101

1/6W68RB15

RR05

1/6W7.5KR105

SKB01

DMS-200D

50V33PFCG03

C118

SK101WSP-401M

100pF50V

RG101501/2W

P100V

MO1W39ohmR130

G21

22NFC113

CR02

50V1uF

70V

RR0718K

70V

CR0333PF50V

G

8H

DR011N4148

1A

2B

3C

4D

5E

6F

7

EY11

LM2480NAIC104

1/2W390R103

560

1/8W

RG03

DR021N4148

5V

1SS244DR04

500V

MO50V100nFC151

1KV1nFC120

1.8nFC114

B_OUT

R_OUT

G_OUT

CB0333PF50V

G2

AFC

15 20

19

14

16

21

23

10-3 AN15VS MINI_MVT Video Part Schematic Diagram


10-6 AN15V*

14 1.00 V (IC101 #13, 14, 16) 15 0.5 V (IC101 #18,21,24) 16 20.0 V (IC102, #9, 10, 11) 19 2.00 V (IC101, #1)

20 1.00 V (IC101, #18,21,24) 23 50.00 V (CRT Socket, G1)21 10.0 V (R,G,B, Video)

CH1 P-P = 10.0V CH1 RMS = 17.02V

Samsung Electronics Co.,Ltd.416, Maetan-3Dong, Paldal-Gu, Suwon City, Kyungki-Do, Korea.Printed in KoreaP/N : BH82-00005E-00http://www.samsungmonitor.com (SyncMaster Worldwide)http://www.samsung-monitor.com (SyncMaster USA)http://www.sec.co.kr/monitor (Korea)

Samsung An15vs Samtron 56v 56e Samsung 551v s

Documents

Transcript of Samsung An15vs Samtron 56v 56e Samsung 551v s