SAILOR SYSTEM 5000 GMDSS CONSOLE - peel.dk System 5000 GMDSS Console (Technical... · TECHNICAL...

TECHNICAL MANUAL

SAILOR SYSTEM 5000 GMDSS CONSOLE

Disclaimer

Any responsibility or liability for loss or damage in connection with the use of this product and theaccompanying documentation is disclaimed by Thrane & Thrane. The information in this manual isprovided for information purposes only, is subject to change without notice and may contain errors orinaccuracies.

Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on thisinformation should acquire the most current version e.g. from the Thrane & Thrane Extranet athttp://extranet.thrane.com.

Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, inwhole or in part, of this manual from any other source.

0935

Console 5000

0930

CONTENTS

1 General information .......................................................................... 1-1

2 Installation ......................................................................................... 2-12.1 Dimensions.......................................................................................... 2-12.2 Drilling and cutting template ................................................................ 2-42.2.1 Tabletop mounting for 325mm and 400mm section ............................ 2-42.2.2 Tabletop mounting for 3 x 400mm section .......................................... 2-42.2.3 Bulkhead mounting for 325mm and 400mm section ........................... 2-52.2.4 Bulkhead mounting for 3 x 400mm section ......................................... 2-52.2.5 Earth stubs mounting .......................................................................... 2-62.2.6 Placement of print ............................................................................... 2-62.3 Mounting the console onto the bulkhead............................................. 2-72.4 Paper roll ............................................................................................. 2-92.5 Control units ........................................................................................ 2-92.6 Message terminal ................................................................................ 2-102.7 Factory configuration of the console ................................................... 2-11

3 Electrical installation ........................................................................ 3-13.1 TT-3606E opt. 003 NMEA Adapter for mini-C ..................................... 3-13.2 Grounding cables ................................................................................ 3-23.3 Console light........................................................................................ 3-33.4 Connection board ................................................................................ 3-43.5 Schematic connection board ............................................................... 3-5

4 Installation cables ............................................................................. 4-14.1 Console wiring system ........................................................................ 4-14.2 Internal cables overview ...................................................................... 4-24.2.1 Internal cables 2 section console w/ MF/HF Radiotelex, mini-C and VHF ....... 4-44.2.2 Internal cables 3 section console w/ MF/HF Radiotelex, mini-C and VHF ....... 4-54.2.3 Internal cables 3 section console w/ MF/HF, 2 x mini-C and VHF ...... 4-64.2.4 Internal cables 1 section console w/ MF/HF and VHF......................... 4-74.3 Installation external cabling ................................................................. 4-84.3.1 External cabling - Emergency light, Battery Panel and position source ........ 4-84.3.2 External cabling - Alarm Panel ............................................................ 4-94.3.3 External cabling - VHF ........................................................................ 4-94.3.4 External cabling - MF/HF..................................................................... 4-104.3.5 External cabling - mini-C and Power supply ........................................ 4-10

1 General information Console 5000

1-10815

1 General information

With the System 5000 GMDSS console, all the communication equipment of the ship can be combinedin one small, compact console.

One of the main purposes of the console is to make the best possible use of the limited space on boarda ship. Furthermore, the fact that all the equipment is kept in the same place makes installation easy andfast. Finally, the modular structure of the system means that it can easily be altered if for example a needto have it extended should arise.

The standard console includes the following: Emergency light, battery panel, and connection board.Furthermore, the console is designed with removable front plates for easy service and maintenance.

The console can be configured to match any maritime communication need. On the following pages,some typical configurations are shown.

1 General information Console 5000

1-2 0815

2 Installation Console 5000

2-10929

2 Installation

2.1 DimensionsConsole type numbers and part numbers refer to console hardware only, i.e. an empty console with only batterypanel, emergency light and connection board(s) installed.

Equipment illustrated for reference only.

Type: 5135CConsole part no.: 405135C-THRxx

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

1645

40

550

0

99-127880

2 pcs. CU51x0 MF/HF Control UnitTT-3043CP Console Panel3 pcs. H1252B Parallel Printer3 pcs. TT-3606E Message Terminal

Weight:excl. units 60 kg.incl. units 89 kg.


BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

1245

40

550

0

375

99-126990

CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP-2 Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal


Type: 5134BConsole part no.: 405134B-THRxx

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

1170

405500

375

99-127178

CU51x0 MF/HF Control UnitTT-3043CP-2 Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal


Type: 5134FConsole part no.: 405134F-THRxx

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

1445

405500

375

99-129806

CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP-2 Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal1 pcs. TT-3670 IP Handset



2-2 0930

Type: 5134GConsole part no.: 405134G-THRxx

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

1645

405500

375

99-129805

CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP-2 Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal



BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

1245

40

550

0

375

99-126991

CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal


Type: 5133GConsole part no.: 405133G-THRxx

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

1645

405500

375

99-129807

CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal



BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

1445

405500

375

99-129808

CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal1 pcs. TT-3670 IP Handset



2-3


BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

845

40

550

0

375

99-126992

CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP Console Panel2 pcs. H1252B Parallel PrinterTT-3606E Message Terminal



BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

1045

405500

375

99-129809

CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP Console Panel2 pcs. H1252B Parallel PrinterTT-3606E Message Terminal1 pcs. TT-3670 IP Handset


Type: 5132BConsole part no.: 405132B-THRxx

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

770

40

550

0

375

99-127179

CU51x0 MF/HF Control UnitTT-3043CP Console Panel2 pcs. H1252B Parallel PrinterTT-3606E Message Terminal


Type: 5131AConsole part no.: 405131A-THRxx

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

445

405

375

99-126993

CU51x0 MF/HF Control UnitRT502x VHF Radio


0930


2-4

2.2 Drilling and cutting templateThe console can be placed and mounted, in several different ways, to ensure optimal integration into theuser environment.

2.2.1 Tabletop mounting for 325mm and 400mm section

35846A

Cut for cable entry

for 325mm section.

325

25

375

300

115

85

65

4 mounting holes (ø6)

150

400


Cut for cable entry

for 400mm section.

25

NB! The table must be sufficiently supported

to carry the console.

****

Drilling template Drilling template

775

727.5

700

400

372.5

327.5

300

75

47.5

0 720

380

320

55

2.2.2 Tabletop mounting for 3 x 400mm section

99-126894

Cut for cable entry

400

25

375

300

115

85

65

150

400


Cut for cable entry

25

NB! The table must be sufficiently supported

to carry the console.

****

400


Cut for cable entry

for 400mm section.

Drilling template


1250

1202.5

1175

875

847.5

802.5

775

475

447.5

402.5

375

75

47.5

0 1195

855

795

455

395

55

0815


2-5

2.2.3 Bulkhead mounting for 325mm and 400mm section

Earth stubs entry. Earth stubs entry.

35847B

100 100

0

405

254

300

25

****

**25**

for 325mm section.

Drilling template

for 400mm section.

Drilling template

775

700

637.5

400

387.5

350

312.5

300

75

62.5

0

400325

2.2.4 Bulkhead mounting for 3 x 400mm section


99-126895

100 100

0

405

300 ****

****

for 400mm section.

Drilling template

Earth stubs entry.

100

**

0

261.3

167.3

73.3

254

130.3

2525

400400400

1250

1203

1175

1033

1017

875

847

775

743.5

545.5

475

375

343.5

145.5

75

0

* To avoid vibration noise, the console should be fastened with screws onto the bulkhead.

** Space from last left- and righthand section to wall.(22.5 + spacing = 25mm)

0815


2-6

2.2.5 Earth stubs mounting


99-127882

100 100

Earth stubs entry.

100

100mm

40mm

15mm

30mm

copper

4 pcs. M6 bolts

Earth stubs made of steel and

welded to the steel bulkhead.

15mm

100mmx0.5mm

0

187.5

587.5

987.5

2.2.6 Placement of print

Earth stubs entry Earth stubs entry

99-129820

100 100

Earth stubs entry

100

Mini-C

Interconnection

Board (1)

Mini-C

Interconnection

Board (2)

Connection

Board (1)

Connection

Board (2)

0930


2-7

2.3 Mounting the console onto the bulkheadWhen the console is placed on a table, the back of the console can be attached onto the bulkhead.This allows for free access to the connection board and wiring while installing.

1 Remove the rear (back cover) panels, by removing all 6 screws in each panel.(These will not be needed further and may be discharged of).

2 Remove the edge-profile, from top of the right end of the console (3 screws).3 Remove the plate on the right end of the console (5 screws).

99-126994

2

3

1

4 Remove all key-hole screws from the back.5 Using a hacksaw, cut away the back part, of the bottom plate, by following the pre-cut lines.

Do this on sections, where connection boards are fitted.

99-126995

*

**

**

*

4

5

9

0815


2-8

6 Mount all key-hole screws, from the inside of the console.

99-126996

6

**

7 Fasten the console to the bulkhead,with 2 screws per section.

8 Loosen key-hole screws and lift up the front part.

7

Lift here

99-127884

8

12

*

*

*

*

*

*

*

*

*

*

*

*

9 At this point connection board wiring may be donewhile having free access to the connection boards.

10 Fit the front part back onto the key-hole screws.11 Fasten key-hole screws.12 Fasten the console to the table, with four screws per section13 Reinstall the plate, removed in step 3.14 Reinstall the edge-profile, removed in step 2.

0815


2-9

2.4 Paper roll

99-126893

min. 680 Clearance required above console

to open top for access to

printer paper roll.

2.5 Control units

99-127913

4 screws M4x4

6 screws M4x6

4 screws M4x8

0815


2-10 0815

2.6 Message terminal

37209B

4 screws M4x10


2-11

2.7 Factory configuration of the consoleWhen the System 5000 Console is ordered along with the relevant equipment sets and Service Pack partnumber (Service Pack denotes factory installation of units in console) the configuration of the equipmentwill be as per the following notation:

In consoles with two handsets and hence two radio control units, the left side handset is always associatedwith the upper most control unit (MF/HF CU).Supplied with the Console accessory kit are self adhesive labels which may be used to mark therespective handsets for MF/HF and VHF, for ease of identification (Fig. 1).

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

99-128517

MF/HF

VHF

MF/HF 2

Fig.1

Equipment configuration:With two TT-3000EB mini-C installed (Fig. 2) the printer and Message Terminal/keyboard associated with#1 mini-C (part of primary GMDSS equipment) is installed in the left hand side of the console and theassociated mini-C Alarm Panel being the left hand one. The #2 mini-C equipment (part of duplicationGMDSS equipment) is installed in the right hand side, the mini-C Alarm Panel being the right hand one.Both Message Terminals will be configured with the Capsat application software program.The MF/HF controller is installed as the upper most unit (as part of System #1 or primary GMDSSequipment) and the #1 VHF installed below the MF/HF Control Unit also as part of the #1 System orprimary GMDSS equipment.

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

99-128512

#1 mini-C

#1 printer

#1 keyboard

#2 mini-C

#2 printer

#2 keyboard

Fig.2

0815


2-12

With one TT-3000EB mini-C and the full MF/HF Radio Telex installed (Fig. 3) the MF/HF Control unit isinstalled as the upper most unit being part of System #1 or primary GMDSS equipment with associatedRadio Telex Message terminal/keyboard and printer installed in the left hand side of the console. Samenotation applies in case of the GMDSS Radio Telex solution without Message Terminal (2-sectionconsole - Fig. 4).The #1 VHF is installed below the MF/HF Control Unit as part of the #1 System or primary GMDSSequipment.The TT-3000EB mini-C is installed in the right hand side of the console being part of System #2 orduplication GMDSS equipment. In the case of two Message Terminals (Fig. 3) these are configured withthe Radio Telex application software program and the Capsat application software program respectively.

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

99-128513

Radiotelex #2 mini-C

mini-C printer

Keyboard

Radiotelex printer

Keyboard

Fig. 3

BATTERY

ALARM

V

1GENCY

EMER-

LIGHT

BATTERY 1

BATTERY 2

2

A

2AC1

ALARM

MUTE/

1 - 2

BATT

DIM

TEST

99-128531

Radiotelex

#2 mini-C

#2 mini-C printer

KeyboardKeyboard

printer

Fig. 4

3 Electrical Installation Console 5000

3-10815

3 Electrical installation

3.1 TT-3606E opt. 003 NMEA Adapter for mini-CIn case the position information generated by the build in GPS receiver of the TT-3026C mini-CTransceiver is required for feeding to other external communication equipment like VHF radios etc., theTT-3606E Opt. 003 NMEA Adapter is required to adapt the information into proper NMEA signal levels.

99-127912

When installing the TT-3606E Opt. 003 NMEA Adapter in the console, the cover of the Adapter box maybe discarded of.

Please refer to the installation manual delivered with the TT-3606E Opt. 003 NMEA Adapter for furtherinstallation information (TT 98-124401). Manual is also available for download from the T&T Extranet/eSupport download area.


3-2 0815

3.2 Grounding cablesGrounding of all external cable screens to the console is important in order to reduce risc of noise andinterference in the GMDSS installation.

The screen of each external cable must be properly terminated to the support bracket by means of a cablelug properly secured to the support bracket with a screw.

99-127906

All internal cable screens are grounded to the support bracket using tie wraps.

99-127907


3-30815

3.3 Console light

Functional descriptionThe intention is to supply the console workplace, with sufficient ambient light for working. If desired, thelight can be turned off completely, so that it does not distract the ship operator, for example during nighttime. However when required the light can be turned on quickly, by means of a switch.

By turning the dimming potentiometer clockwise, the light intensity increases, and correspondinglyturning the potentiometer anti clockwise decreases the light intensity.

The light can be switched on or off, by pushing the to-way switch located just below the dimmingpotentiometer.

If an external two-way light switch is installed for remote control of this console light, this switch shouldbe connected to the appropriate terminals on the primary connection board.

The gooseneck lamp is fed by a regulated DC voltage. The max. voltage supplied to the gooseneck lampis around above 12VDC.

The gooseneck lamp comprise a 3 pin XLR-plug with a release button. Pin 2 carries positive supplyvoltage (+), pin 3 is connected to DC-. Pin 1 is not connected.

The supply for the dimming module is routed from the emergency batteries, through the connection board.

The light source is either by white LED´s or red LED´s. The use of LED´s greatly reduces currentconsumption and heat dissipation normally associated with incandescent lamps.

24V_Light+

24V-

Battery switch

External

circuit

Dimming

Gooseneck

connection

If an external switch is not installed, a jumper wire

GND

24V-

should be placed between "24V_Light+" and "M1".99-126892

M1

M2

3

21


3-4 0815

3.4 Connection boardThe connection board has been designed, so that connectors are grouped in relation to products.

Each connector has been given a unique name and designator in order to clearly identify the connector.Also where the wires are mounted into terminal strips, each connection has been named. The first digitof a designator, is a consecutive number, and the second digit is a digit only used for connectionsbelonging to that group. Every designator starts with an „X“, to indicate that this is a type of connector.For example, the first connector for VHF connection carries the designator „X21“, the second connector„X22“ and so on.

The only connector that differs from the above description, is the connector „Remote“, also designated„X71“. This connector joins the remote function for both „MINI-C“ and „TELEX“.

In consoles with two connection boards, the primary equipment connects to the left connection board. Theduplication equipment connects to the right connection board. This means that for example in commu-nications systems with two VHF radios, the primary VHF is the one located in the console and connectsto the left connection board. The duplication VHF will, if connected through the console connect, to theright hand side connection board.

Component location connection board

X44

X43


3-5

3.5 Schematic connection board

0815


3-6 0815

4 Installation cables Console 5000

4-10815

4 Installation cables

4.1 Console wiring systemThe internal wiring of the console has been grouped and numbered in the following drawings, so that eachcable is easily identified by its unique identifier.

NumberingThe numbering is grouped in three digits, as indicated below. The type of signal carried is also indicatedin the table listing the internal cables.

X.Y.ZZ

C7 = Primary internal 1 = RF/Antenna X.2.00 through 19 = Control/DataC8 = Duplication, backup, internal 2 = Signals X.2.20 through 29 = Relay outputC9 = Common internal 3 = DC power X.2.30 through 39 = Ext. signal

4 = AC power X.3.00 through 09 = Heavy duty DC (distribution)

X.3.10 through 19 = Single power


4-2 1035

4.2 Internal cables overview

Cable No. Cable type From/To From/To Part No. Signal Conn.

C7.1.00 PL-PL RT50xx RF-Plug 527830 VHF Main RF 1:1C7.1.01 PL-PL RT50xx RF-Plug 527830 VHF DSC RF 1:1

C7.2.00 9-9 pole Sub D CU51x0 MF/HF 56.123 AUX 1:1C7.2.01 9-9 pole Sub D CU51x0 MF/HF 56.123 SCAN-BUS 1:1C7.2.02 Centronics 25 pole Data Terminal/CU Printer Supplied Message 1:1C7.2.03 2 pole mini-C Remote 56.121 On/Off 2C7.2.04 9-9 pole Sub D Data Terminal TT-3616C Supplied Data 1:1C7.2.05 Multi Cable TT-3616C TT-3043CP-2 37-122732-A Data 3C7.2.06 15-15 pole Sub D RT50xx 37-126527 Option 8C7.2.07 15-15 pole Sub D RT50xx 37-126528 SPARC-II 9C7.2.12 8 pole mini din Printer Paper switch 56.122 Control 4C7.2.14 9-9 pole Sub D Data Terminal CU51x0 MF/HF Supplied Data 1:1

C7.3.10 Power Cable Printer Supplied DC supply MC7.3.11 Power Cable Data Terminal Supplied DC supply MC7.3.12 Power Cable TT-3616C 37-123214-B DC supply 5C7.3.13 Power Cable RT50xx Supplied DC supply M

C8.1.00 PL-PL RT50xx RF-Plug 527830 VHF Main RF 1:1C8.1.01 PL-PL RT50xx RF-Plug 527830 VHF DSC RF 1-1

C8.2.00 15-15 pole Sub D RT50xx 37-126527 Option 8C8.2.01 15-15 pole Sub D RT50xx 37-126528 SPARC-II 9C8.2.02 Centronics 25 pole Data Terminal Printer Supplied Message 1:1C8.2.03 9-9 pole Sub D Data Terminal TT-3616C Supplied Data 1:1C8.2.04 Multi Cable TT-3616C TT-3043CP-2 37-122732-A Data 3C8.2.05 2 pole mini-C Remote 56.121 On/Off 2C8.2.06 8 pole mini din Printer Paper switch 56.122 Control 4

C8.3.10 Power Cable RT50xx Supplied DC supply MC8.3.11 Power Cable Printer Supplied DC supply MC8.3.12 Power Cable Data Terminal Supplied DC supply MC8.3.13 Power Cable TT-3616C 37-123214-B DC supply 5

C9.2.01 9-9 pole Sub D Battery Panel 56.123 Batt Sense 1:1C9.2.02 9-9 pole Sub D Battery Panel 56.123 Batt Sense 1:1

C9.3.10 Cable, 2 pole Emg. light/gooseneck 37-126773 DC supply 6C9.3.11 Cable, 4 pole Emg. light-dimmer 37-126772 DC supply 7

Notes:- Where „From/To“ is left blank, the cable is terminated at the connection board 59-126095.

See relevant internal wiring diagrams, for further information.

- „Supplied“ = Designates cable that is supplied with a product, and therefore does not have its ownpart number.

- M = Consult the technical manual for the product.

- Where „Conn.“ is marked with „1:1“, this means that the cable ends are wired pin number 1 to pinnumber 1, pin number 2 to pin number 2, and so on for further pin numbers.Other markings at „Conn.“, refers to cable wiring connection drawings, at the following pages.

2: mini-C Remote, 2 pole:The two wires are soldered on to two terminals, on an on/off push-button switch.


4-30815

3: Multi cable, TT3043CP-2:TT-3616C TT-3043CP-2+9VDC, White Pin 1GND, Brown Pin 2I/O 0, Red Pin 3I/O 1, Gray Pin 4I/O 2, Yellow Pin 5I/O 3, Green Pin 6I 4, Blue Pin 7I 5, Pink Pin 8

Pin 9, Not connectedPin 10, Not connectedPin 11, Not connectedPin 12, Not connected

Please refer to the installation manual delivered with the TT-3000EB mini-C GMDSS system for furtherinstallation information (TT 98-122414).

4: mini din, paper switch:The two conductors are soldered respectively to pin 1 and pin 2, of the paper switch.Screen is soldered to the bracket for the paper switch.

5: Power cable, TT-3616C:Connection board TT-3616CPin 1, +24V, Red DC +Pin 2, -24V, Black DC -Pin 3, Remote, White Remote On/Off

6: Cable, 2 pole, Emg. light/gooseneck lamp:Connection board Gooseneck lampPin 1 Gooseneck + Pin 2, Light supplyPin 2 - Light Pin 3, Light ref.

7: Cable, 4 pole, Emg. light-dimmer:Dimmer Connection boardPin 1 Pin 2, - LightPin 2 Pin 1, M1Pin 3 Pin 3, M2Pin 4 Pin 4, Gooseneck +

8: Option, 15 pole SUB D connector:Only wire numbers 12, 13 and the screen, is fed through this cable.All other pin numbers has no connection.

9: SPARC-II, 15 pole SUB D connector:Only wire numbers 2, 3, 6, 7 and the screen, is fed through this cable.All other pin numbers has no connection.


4-4 1035

4.2.1 Internal cables 2 section console w/ MF/HF Radiotelex, mini-C and VHF

99-1

2632

8-A

Prin

ter

On/

Off

Key

boar

d

Bat

tery

Pan

elP

rinte

r

Dat

a T

erm

inal

Inte

rcon

nect

ion

Boa

rdT

T-3

616C

RT

50xx

(rea

r vi

ew)

MF

/HF

CU

51x0

min

i-CT

T-3

043C

P

Key

boar

d

Ligh

tE

mer

genc

y

C7.

2.00

C7.

2.01

C7.

2.12 C7.

1.00

C7.

1.01

C7.2.07C

8.3.

13C

8.3.

12C

8.3.

11C

8.2.

05

C8.

2.03

C8.

2.04

C8.

2.02

C8.

2.06

C9.

2.02

C9.

2.01

C9.

3.11

C9.3.10

C7.3.13

C7.2.06C

7.3.

10

C7.

2.02

Han

dset

AU

XS

CA

N-B

US

Key

boar

dD

ata

Prin

ter

Bat

tery

1B

atte

ry 2

Bat

tery

1B

atte

ry 2


4-51035

4.2.2 Internal cables 3 section console w/ MF/HF Radiotelex, mini-C and VHF

99-1

2632

9-APrin

ter

Key

boar

d

Prin

ter

Dat

a T

erm

inal

Inte

rcon

nect

ion

Boa

rdT

T-3

616C

MF

/HF

CU

51x0

Key

boar

d

Dat

a T

erm

inal

Bat

tery

Pan

el

RT

50xx

(rea

r vi

ew)

On/

Off

min

i-CT

T-3

043C

P

Ligh

tE

mer

genc

y

On/

Off

C7.

2.00

C7.

2.01

C7.

2.12

C7.

3.11

C7.

3.10

C7.

2.06

C7.

2.07

C7.

1.00

C7.

1.01

C8.

3.13

C8.

3.12

C8.

3.11

C8.

2.05

C8.

2.03

C8.

2.04

C8.

2.02

C8.

2.06

C9.

2.02

C9.

2.01

C9.

3.11

C9.3.10

C7.

2.02

C7.3.13

C7.

2.14

C7.2.03

Han

dset

AU

XS

CA

N-B

US

Key

boar

dD

ata

Prin

ter

Bat

tery

1B

atte

ry 2

Bat

tery

1B

atte

ry 2


4-6

4.2.3 Internal cables 3 section console w/ MF/HF, 2 x mini-C and VHF

99-1

2633

1-APrin

ter

Key

boar

d

Bat

tery

Pan

elP

rinte

r

Dat

a T

erm

inal

Inte

rcon

nect

ion

Boa

rdT

T-3

616C

RT

50xx

(rea

r vi

ew)

MF

/HF

CU

51x0 K

eybo

ard

Dat

a T

erm

inal

Inte

rcon

nect

ion

Boa

rdT

T-3

616C

On/

Off

On/

Off

min

i-CT

T-3

043C

P-2

Ligh

tE

mer

genc

y

C7.

2.00

C7.

2.01

C7.

2.12

C7.

2.02

C7.

3.12

C7.

3.11

C7.

3.10

C7.

2.03

C7.

2.04

C7.

2.05

C7.

2.06

C7.

1.00

C7.

1.01

C7.

3.13

C8.

3.13

C8.

3.12

C8.

3.11

C8.

2.05

C8.

2.03

C8.

2.04

C8.

2.02

C8.

2.06

C9.

2.02

C9.

2.01

C9.3.10

C9.

3.11

C7.

2.07

Han

dset

AU

XS

CA

N-B

US

Key

boar

dD

ata

Prin

ter

Bat

tery

1B

atte

ry 2

Bat

tery

1B

atte

ry 2

1035


4-7

4.2.4 Internal cables 1 section console w/ MF/HF and VHF

99-126332-A

Battery Panel

RT50xx(rear view)

MF/HFCU51x0

LightEmergency

C7.2.01

C7.2.00

C7.1.00 C7.1.01

C7.

2.06

C7.

2.07

C7.

3.13

C9.2.01C9.

3.10

C9.3.11Handset AUX SCAN-BUS

Keyboard Data Printer

Battery 1 Battery 2Battery 1 Battery 2

1035


4-8

4.3 Installation external cabling

4.3.1 External cabling - Emergency light, Battery Panel and position source

99-127898

M1

24V+

External switch

24V-

24V+

Charger

M21

2

3

GND

NMEA -

Position source

NMEA +

-SHUNT

+SHUNT

Power supply/Charger

+VBAT

External shunt box/

1

2

3

AC ALR 1

AC ALR 2

-VBAT4

5

6

24V DC-

24V DC+

AC ALR 07

8

9

1

2

1

2

3

1

2

3

4

5

6

7

8

9

0815


4-9

4.3.2 External cabling - Alarm Panel

99-127899

GND

SPARC-BUS -

MF/HF - X4

SPARC-BUS + 3

5

2

+24V 9

5065

GND

SPARC-BUS -

VHF - X3

SPARC-BUS + 3

5

2

+24V 9

D-sub

D-sub

D-sub

D-sub

To # 1 mini-C connection board

To # 2 mini-C connection board

1

2

3

4

1

2

3

4

3,7

4,5

8,9

1,2GND

Data +

Data +

VCC IN

3,7

4,5

8,9

1,2GND

Data +

Data +

VCC IN

4.3.3 External cabling - VHF

99-127900

24V DC+

24V DC-

Power Supply

1

2

0815


4-10

4.3.4 External cabling - MF/HF

99-127901

24V DC +

24V DC -

Power Supply

+24V7

Rx AF+8

Transceiver

SCAN-BUS

AF -5

GND6

Data -3

AF +4

Supply on1

Data +2

Rx AF-9

1

2

7

8

5

6

3

4

1

2

9

D-sub

4.3.5 External cabling - mini-C and Power supply

99-127902

24V DC +

24V DC -

Power Supply

1

2

0815

Thrane & Thrane A/S • [email protected] • www.thrane.com

TT-98-127000-THR-C Issue: C/1035

SAILOR SYSTEM 5000 GMDSS CONSOLE - peel.dk System 5000 GMDSS Console (Technical... · TECHNICAL...

Documents

Transcript of SAILOR SYSTEM 5000 GMDSS CONSOLE - peel.dk System 5000 GMDSS Console (Technical... · TECHNICAL...