SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet...
Transcript of SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet...
![Page 1: SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet and under sil cover –follow harness to kick panel Remove rubber door seal and](https://reader030.fdocuments.in/reader030/viewer/2022040904/5e778f08d7c2f37a4e7416ba/html5/thumbnails/1.jpg)
SAIC T60 AUTOMATIC HARD LID
INSTALLATION
Remove sports bars and place on cushioned surface
Open fittings sleeve
![Page 2: SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet and under sil cover –follow harness to kick panel Remove rubber door seal and](https://reader030.fdocuments.in/reader030/viewer/2022040904/5e778f08d7c2f37a4e7416ba/html5/thumbnails/2.jpg)
Sports bar brackets
Remount feet with spacer washers under infil moulding
Install foam seal up front across tubliner
![Page 3: SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet and under sil cover –follow harness to kick panel Remove rubber door seal and](https://reader030.fdocuments.in/reader030/viewer/2022040904/5e778f08d7c2f37a4e7416ba/html5/thumbnails/3.jpg)
Replace sports bars and mount support bracket
Mount hinges on lid , put on vehicle, centre and mark female hinge position . mount hinges with
self tapping bolts thru liner.
![Page 4: SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet and under sil cover –follow harness to kick panel Remove rubber door seal and](https://reader030.fdocuments.in/reader030/viewer/2022040904/5e778f08d7c2f37a4e7416ba/html5/thumbnails/4.jpg)
Remove male lid hinge and assemble (lubricate pins) replace lid and re attach .
Attach pre assembled closed strut to lid and lay back to mount on tub edge
![Page 5: SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet and under sil cover –follow harness to kick panel Remove rubber door seal and](https://reader030.fdocuments.in/reader030/viewer/2022040904/5e778f08d7c2f37a4e7416ba/html5/thumbnails/5.jpg)
Attach support bracket and drill mount botton support bolt . attach thru tub with nyloc knut
Inser stabiliser bolt and tighten
![Page 6: SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet and under sil cover –follow harness to kick panel Remove rubber door seal and](https://reader030.fdocuments.in/reader030/viewer/2022040904/5e778f08d7c2f37a4e7416ba/html5/thumbnails/6.jpg)
Feed wire thru tub use grommet to protect wire thru the hole feed wire thru chassis on drivers side
With a bit plastic blue tongue attached to wire come out near the underside of the drivers seat.
![Page 7: SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet and under sil cover –follow harness to kick panel Remove rubber door seal and](https://reader030.fdocuments.in/reader030/viewer/2022040904/5e778f08d7c2f37a4e7416ba/html5/thumbnails/7.jpg)
Come up attach grommet and under sil cover –follow harness to kick panel
Remove rubber door seal and kick panel , attach control module to inside of panel feed power wire
across underneath Intrument panel and go thru the firewall to the battery
![Page 8: SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet and under sil cover –follow harness to kick panel Remove rubber door seal and](https://reader030.fdocuments.in/reader030/viewer/2022040904/5e778f08d7c2f37a4e7416ba/html5/thumbnails/8.jpg)
Mount isolater swich on kick panel and leave 5A safety fuse accessible . attach to battery with
separate 10 Amp fuse
![Page 9: SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet and under sil cover –follow harness to kick panel Remove rubber door seal and](https://reader030.fdocuments.in/reader030/viewer/2022040904/5e778f08d7c2f37a4e7416ba/html5/thumbnails/9.jpg)
Pierce grommet and feed wire thru fire wall
Use conduit on wire anywhere under the bonnet , use cable ties to secure.
![Page 10: SAIC T60 AUTOMATIC HARD LID INSTALLATION Fitting guide.pdf · 2018-07-18 · Come up attach grommet and under sil cover –follow harness to kick panel Remove rubber door seal and](https://reader030.fdocuments.in/reader030/viewer/2022040904/5e778f08d7c2f37a4e7416ba/html5/thumbnails/10.jpg)