4000665 Rev. B

Operation Guide

Full documentation available online: www.eSightEyewear.com/ManualsPrint documentation available at no charge: 1-855-837-4448 ext 555 Warranty information available online: www.eSightEyewear.com/Warranty

Stationary

a) Tilt Down

• Reading• Watching TV• Crafts

Mobile & Stationary

b) Tilt Half-Up

• Sightseeing• Grocery shopping • Working on a

computer

Social & Mobile

c) Fully Up

• Speaking with someone

• Walking in a mall• Eating dinner

5. Use

Safety Be safe. Before using eSight, read the Safety and Care booklet.

4. Control

magnify

hold to power focus

contrast

Do not drive or operate any motorized vehicle.Do not walk with eSight in the fully down position.Do not use eSight in rainy, snowy, or stormy conditions.Do not use unapproved batteries, power supplies or cords, as this may cause serious injury, fire, or battery explosion.

1.2.3.4.

5. Do not use the wireless features of eSight in a hospital, on an aircraft, or near equipment that can be interfered with by radio frequency.

4000558 Rev. A © Copyright 2017, eSight Corporation. All rights reserved.

1. Replace the forehead band. Follow the instructions in the eSight 3 User Guide.

2. To adjust, hold the forehead band as shown, and slide the ratchet strip

forward or backward to enlarge or shorten the band.

3. Put on eSight 3, then connect and adjust the headstrap.

When properly fitted, you’ll have a slight gap of approximately 1 mm between

the top of your frames and your forehead. See “Achieving the Perfect Fit” in

the eSight 3 User Guide.

HOLD

SLIDE

Adjustable Forehead Band

Adjusting the ZoomZoom In or OutRotate Up or Down

Spot ZoomPush and Hold to Temporarily Zoom Out to the Full Field of View

Powering the Eyewear

ON / Resume – Push & Hold

OFF – Push & Hold. Slide Finger on Trackpadto Highlight SHUTDOWN.Push Trackpad.

STANDBY – Push & Hold. Push again to select STANDBY.

Attach the Eyeglass Frames

Slide eyeglass frames into headset until headset magnet lines up with metal dot on both sides of eyeglass frames.

When frames are lined up with the magnet, you should hear a “click”.

Unlock / Lock Menu

Push & Hold5 Seconds

Open Menu /Select Option

PushGo Back / Exit Menu

Push Once /Push until Menu Gone

Unlock / Lock the Controller

Push & Hold5 Seconds

Browse Menu

Slide Fingeron Trackpad

Using the Menu

Lower Bioptic Position Upper Bioptic Position Fully Up

Adjusting the FocusRotate Up or Down to Adjust Focus• Fine-tune Focus in Auto Focus Mode

• Adjust Focus in Manual Focus Modes

Adjusting the ContrastRotate to Adjust Contrast

Push to Switch Focus Mode2 – Near Manual

3 – Far Manual

1 – Auto

Push to Switch Contrast Mode2 - Black on White3 - White on Black4 - Black on Yellow5 - Blue on White6 - Blue on Yellow7 - Yellow on Blue8 - Grayscale1 - Normal (Full Color)

“click”

A B

The eSight 3 headset can be tilted through a wide range of positions. Below are common positions and their uses.

Tilt the Headset Daily Usage

Wear your eSight 3

Tighten the Headstrap

• Headset fully down• Allows you to use your peripheral vision and look directly at the displays• Useful for activities like reading, crafts, and watching T.V.

• Headset is partially upright to view with displays and lenses

• Allows you to use your peripheral vision and glance up into the headset displays for greater detail

• Useful for mobility and working with screens

• Headset fully up

• Can use frame lenses

• Cannot view displays

• Useful when you need the headset out of the way temporarily

TIP If your Eyewear is too close or too far away from your face, adjust the forehead band for the proper fit. See the eSight 3 User Guide for instructions.

4000372 Rev. B September, 2017

Attach the Left HeadstrapBPut connector over magnetic contact point on forehead band

The Perfect Fit• Frames worn like a pair of spectacles• Forehead band fits snugly against your forehead• Headstrap fits snugly around your head.• Headset and frames should feel weightless on the bridge of your nose• Headset and frames should not move when you shake your head

CPut on eSight 3A

b)

a)

d)

Use the USB cable in the pouch

Connect cable to controller and power block

c) Plug power blockinto wall socket

100-240 V

View Charge IndicatorWait until light is GREENeSight 3 must be charged prior to first use.

a) Adjust as needed (from back of head)

b) Remove eSight from head to adjust forehead strap as needed

Plug intothe Wall

0% Charging 100%

3. Adjust1. Charge

FLIP

4000558 Rev. A © Copyright 2017, eSight Corporation. All rights reserved.

1. Replace the forehead band. Follow the instructions in the eSight 3 User Guide.

2. To adjust, hold the forehead band as shown, and slide the ratchet strip

forward or backward to enlarge or shorten the band.

3. Put on eSight 3, then connect and adjust the headstrap.

When properly fitted, you’ll have a slight gap of approximately 1 mm between

the top of your frames and your forehead. See “Achieving the Perfect Fit” in

the eSight 3 User Guide.

HOLD

SLIDE

Adjustable Forehead Band

Adjusting the ZoomZoom In or OutRotate Up or Down

Spot ZoomPush and Hold to Temporarily Zoom Out to the Full Field of View

Powering the Eyewear

ON / Resume – Push & Hold

OFF – Push & Hold. Slide Finger on Trackpadto Highlight SHUTDOWN.Push Trackpad.

STANDBY – Push & Hold. Push again to select STANDBY.

Attach the Eyeglass Frames

Slide eyeglass frames into headset until headset magnet lines up with metal dot on both sides of eyeglass frames.

When frames are lined up with the magnet, you should hear a “click”.

Unlock / Lock Menu

Push & Hold5 Seconds

Open Menu /Select Option

PushGo Back / Exit Menu

Push Once /Push until Menu Gone

Unlock / Lock the Controller

Push & Hold5 Seconds

Browse Menu

Slide Fingeron Trackpad

Using the Menu

Lower Bioptic Position Upper Bioptic Position Fully Up

Adjusting the FocusRotate Up or Down to Adjust Focus• Fine-tune Focus in

Auto Focus Mode

• Adjust Focus inManual Focus Modes

Adjusting the ContrastRotate to Adjust Contrast

Push to Switch Focus Mode2 – Near Manual

3 – Far Manual

1 – Auto

Push to Switch Contrast Mode2 - Black on White3 - White on Black4 - Black on Yellow5 - Blue on White6 - Blue on Yellow7 - Yellow on Blue8 - Grayscale1 - Normal (Full Color)

“click”

A B

The eSight 3 headset can be tilted through a wide range of positions. Below are common positions and their uses.

Tilt the Headset Daily Usage

Wear your eSight 3

Tighten the Headstrap

• Headset fully down• Allows you to use

your peripheral visionand look directly atthe displays

• Useful for activities likereading, crafts, andwatching T.V.

• Headset is partiallyupright to view with displays and lenses

• Allows you to use yourperipheral vision andglance up into theheadset displays forgreater detail

• Useful for mobility andworking with screens

• Headset fully up

• Can use frame lenses

• Cannot view displays

• Useful when you needthe headset out of theway temporarily

TIP If your Eyewear is too close or too far away from your face, adjust the forehead band for the proper fit. See the eSight 3 User Guide for instructions.

4000372 Rev. B September, 2017

Attach the Left HeadstrapBPut connector over magnetic contact point on forehead band

The Perfect Fit• Frames worn like a pair of spectacles• Forehead band fits snugly against your forehead• Headstrap fits snugly around your head.• Headset and frames should feel weightless on the

bridge of your nose• Headset and frames should not move when you shake your head

CPut on eSight 3A

b)

a)

d)

Use the USB cable in the pouch

Connect cable to controller and power block

c) Plug power blockinto wall socket

100-240 V

View Charge IndicatorWait until light is GREENeSight 3 must be charged prior to fi rst use.

a) Insert glasses

b) Put eSight on head like a pair of glasses

a) Adjust as needed (from back of head)

b) Remove eSight from head to adjust forehead strap as needed

Plug intothe Wall

0% Charging 100%

Adjusting the ZoomZoom In or OutRotate Up or Down

Spot ZoomPush and Hold to Temporarily Zoom Out to the Full Field of View

Powering the Eyewear

ON / Resume – Push & Hold

OFF – Push & Hold. Slide Finger on Trackpadto Highlight SHUTDOWN.Push Trackpad.

STANDBY – Push & Hold. Push again to select STANDBY.

Attach the Eyeglass Frames

Slide eyeglass frames into headset until headset magnet lines up with metal dot on both sides of eyeglass frames.

When frames are lined up with the magnet, you should hear a “click”.

Unlock / Lock Menu

Push & Hold5 Seconds

Open Menu /Select Option

PushGo Back / Exit Menu

Push Once /Push until Menu Gone

Unlock / Lock the Controller

Push & Hold5 Seconds

Browse Menu

Slide Fingeron Trackpad

Using the Menu

Lower Bioptic Position Upper Bioptic Position Fully Up

Adjusting the FocusRotate Up or Down to Adjust Focus• Fine-tune Focus in

Auto Focus Mode

• Adjust Focus inManual Focus Modes

Adjusting the ContrastRotate to Adjust Contrast

Push to Switch Focus Mode2 – Near Manual

3 – Far Manual

1 – Auto

Push to Switch Contrast Mode2 - Black on White3 - White on Black4 - Black on Yellow5 - Blue on White6 - Blue on Yellow7 - Yellow on Blue8 - Grayscale1 - Normal (Full Color)

“click”

A B

The eSight 3 headset can be tilted through a wide range of positions. Below are common positions and their uses.

Tilt the Headset Daily Usage

Wear your eSight 3

Tighten the Headstrap

• Headset fully down• Allows you to use

your peripheral visionand look directly atthe displays

• Useful for activities likereading, crafts, andwatching T.V.

• Headset is partiallyupright to view with displays and lenses

• Allows you to use yourperipheral vision andglance up into theheadset displays forgreater detail

• Useful for mobility andworking with screens

• Headset fully up

• Can use frame lenses

• Cannot view displays

• Useful when you needthe headset out of theway temporarily

TIP If your Eyewear is too close or too far away from your face, adjust the forehead band for the proper fit. See the eSight 3 User Guide for instructions.

4000372 Rev. B September, 2017

Attach the Left HeadstrapBPut connector over magnetic contact point on forehead band

The Perfect Fit• Frames worn like a pair of spectacles• Forehead band fits snugly against your forehead• Headstrap fits snugly around your head.• Headset and frames should feel weightless on the

bridge of your nose• Headset and frames should not move when you shake your head

CPut on eSight 3Ac) Wrap strap around head. Fasten magnetically.

Adjusting the ZoomZoom In or OutRotate Up or Down

Spot ZoomPush and Hold to Temporarily Zoom Out to the Full Field of View

Powering the Eyewear

ON / Resume – Push & Hold

OFF – Push & Hold. Slide Finger on Trackpadto Highlight SHUTDOWN.Push Trackpad.

STANDBY – Push & Hold. Push again to select STANDBY.

Attach the Eyeglass Frames

Slide eyeglass frames into headset until headset magnet lines up with metal dot on both sides of eyeglass frames.

When frames are lined up with the magnet, you should hear a “click”.

Unlock / Lock Menu

Push & Hold5 Seconds

Open Menu /Select Option

PushGo Back / Exit Menu

Push Once /Push until Menu Gone

Unlock / Lock the Controller

Push & Hold5 Seconds

Browse Menu

Slide Fingeron Trackpad

Using the Menu

Lower Bioptic Position Upper Bioptic Position Fully Up

Adjusting the FocusRotate Up or Down to Adjust Focus• Fine-tune Focus in

Auto Focus Mode

• Adjust Focus inManual Focus Modes

Adjusting the ContrastRotate to Adjust Contrast

Push to Switch Focus Mode2 – Near Manual

3 – Far Manual

1 – Auto

Push to Switch Contrast Mode2 - Black on White3 - White on Black4 - Black on Yellow5 - Blue on White6 - Blue on Yellow7 - Yellow on Blue8 - Grayscale1 - Normal (Full Color)

“click”

A B

The eSight 3 headset can be tilted through a wide range of positions. Below are common positions and their uses.

Tilt the Headset Daily Usage

Wear your eSight 3

Tighten the Headstrap

• Headset fully down• Allows you to use

your peripheral visionand look directly atthe displays

• Useful for activities likereading, crafts, andwatching T.V.

• Headset is partiallyupright to view with displays and lenses

• Allows you to use yourperipheral vision andglance up into theheadset displays forgreater detail

• Useful for mobility andworking with screens

• Headset fully up

• Can use frame lenses

• Cannot view displays

• Useful when you needthe headset out of theway temporarily

TIP If your Eyewear is too close or too far away from your face, adjust the forehead band for the proper fit. See the eSight 3 User Guide for instructions.

4000372 Rev. B September, 2017

Attach the Left HeadstrapBPut connector over magnetic contact point on forehead band

The Perfect Fit• Frames worn like a pair of spectacles• Forehead band fits snugly against your forehead• Headstrap fits snugly around your head.• Headset and frames should feel weightless on the

bridge of your nose• Headset and frames should not move when you shake your head

CPut on eSight 3A

2. Wear 3. Adjust1. Charge

FLIP