Safety Ladders: Hot Dip Galvanized/Stainless Steel · Part No. BS-STR- Stainless steel, pickled...

Christian Dalloz Holding Deutschland GmbH & Co. KG, D-95015 Hof, P.O.Box 16 46, Phone +49/92 81/83 02-0, Fax +49/92 81/36 26, [email protected]

Technical specifications are subject to change without notice.

B 1

Safety in Action Fall Protection Systems

06.2

006

Safety Ladders: Hot Dip Galvanized/Stainless Steel

Y-SparGuide-rail profile: 50 x 32 mm. Comes withjoint plate. Mounting brackets extra to order.Recommended mounting distance 1400 mm- max. 1680 mm. Installation of bracket toladder is carried out through the rectangularcut outs in the back of the guide-rail. See pageB 3. Maximum section length: 4480 mm. Rungdistance: 280 mm centres. Step width perside: 150 mm

Galvanized steelWeight: 5,0 kg per metrePart No. YST-<length in mm>

Stainless steel, pickledWeight: 5,0 kg per metrePart No. YA4-<length in mm>

Y-Spar with anti-slipping rungsPerforated rungs for use in slipperyconditions, e.g. in manholes. Guide-railprofile: 50 x 32 mm. Comes with joint plate.Mounting brackets extra to order. Recom-mendet mounting distance 1400 mm - max.1680 mm. Installation of bracket to ladder iscarried out through the rectangular cut outsin the back of the guide-rail. See page B 3.Maximum section length: 4480 mm. Rungdistance: 280 mm centres. Step width perside: 150 mm

Galvanized steelWeight: 5,0 kg per metrePart No. YST-<length in mm>-L

Stainless steel, pickledWeight: 5,0 kg per metrePart No. YA4-<length in mm>-L



B 2


06.2

006

Safety Ladders: Hot Dip Galvanized/Stainless Steel

ConnectorsTo connect Y-ladders. Complete with allmounting screws. Included in the delivery ofeach Y-ladder (page B 1). Must be used whenan existing ladder is cut and reconnected.

Weight: 0,6 kg/eachPart No. 17370



B 3


06.2

006

Fixing points for Y-spar made of galvanized/stainless steel. Using a recommendedmounting distance between brackets of 1.400 mm up to a max. of 1.680 mm.

Warning:For design reasons the guide rail of the ladder must be reinforced if, at the end of the ladder run,the guide-rail rises more than 380 mm above the last mounting bracket. Projections of more than380 mm without extra reinforcement are not permitted. The SÖLL guide rail reinforcementmade of galvanized steel/stainless steel 50 mm x 30 mm x 3 mm is bolted onto the guide rail fromthe back at a distance of 560 mm and must extend down over at least two mounting brackets.

Following ladder section lengthare available upon request:

560 mm840 mm

1120 mm1400 mm1680 mm1960 mm2240 mm4480 mm

Ladder length = 4480 mmRung distance = 280 mm



B 4


06.2

006

Smallest radii for ladders made of galvanized/stainless steel,shown in mm:

Important information for planning:

Bending Y-spar ladder aluminium: Part No. YST-<Typ>Bending Twin ladder aluminium Part No. YA4-<Typ>

Typ 1 Typ 2 Typ 3 Typ 4 Typ 5

The length of the bend depends on the bending radius and on the angle (type 1 + ) and/or off-set (typed 3 - 5).

A = Bottom edge of ladder to salient point of structure

B =Of-set (mm)

C = Angle (max. 15 °)D = Bottom edge to centre of obstruction

E = Width of obstructionF = Upper edge of ladder to off-set

G =Of-set (max. 260 mm)



B 5


06.2

006

Top End-Stop, spring activatedPrevents the fall arrester from either beinginserted incorrectly or accidentally slippingout of the guide-rail. For fitting to the very topof the ladder system. Comes with all fixings.

Stainless steel, pickledWeight: 0,2 kg/eachPart No. 21050

Safety Ladders: Hot Dip Galvanized/Stainless SteelEnd-Stops

Bottom End-Stop, spring activatedPrevents the fall arrester from either beinginserted incorrectly or accidentally slippingout of the guide-rail. For fitting to the verybeginning of the ladder system. Comes withall fixings.


Rigid End-StopDoes not allow the fall arrester being taken outof the very top ladder section. Comes with allfixings.




B 6


06.2

006

Mounting bracketComes with installation elements for fixingladder to bracket. Wall attachment must bedrilled to suit site conditions. Minimum boltdiameter for wall fixing: M 16. Projection in5mm steps of 70 to max. 280mm. By movingand turning the bracket, each point of thestructure can be reached (variable fixingdistance).

Weight: depending on the projection

Galvanized steelPart No. BB-SSTR-<projection in mm>

Stainless steel, pickledPart No. BB-SA4R-<projection in mm>

Special projections (i.e., 163 mm) are realisedby using supporting dishes.

Safety Ladders: Hot Dip Galvanized/Stainless SteelMounting brackets

Note:The projection „L“ is subject to the type of the bracket.



B 7


06.2

006


ClampProjection of 1000mm possible. Comes withall installation elements. When ordering,please state the exact mast diameter „D“ andthe projection „L“.

Material thickness „z“ of the clamp shares:-> till Ø 210 mm "z" = 6 mm-> from Ø 220 mm "z" = 8 mm

Weight: Depending on mast diameter

Mast diameter: min. 60 mmMast diameter: max. 1500 mm

Galvanized steelPart No. BS-STR-<Ø in mm>

Stainless steel, pickledPart No. BS-A4R-<Ø in mm>




B 8


06.2

006


Angle Corner Mounting BracketFor use on corner struts of lattice masts.Projection: 150 mm. Comes with all installationelements. Different projection upon request.Support structure must be checked forsufficient strength. Made of galvanized steel.

For angle leg dimension up to100 mm x 100 mmWeight: 1,2 kg/eachPart No. 11025

For angle leg dimension from110 mm x 110 mm up to 140 mm x 140 mmWeight: 1,4 kg/eachPart No. 14696

For angle leg dimension from 150 mm x 150 mm up to 180 mm x 180 mmWeight: 1,6 kg/eachPart No. 14698

For angle leg dimension from190 mm x 190 mm up to 220 mm x 220 mmWeight: 2,2 kg/eachPart No. 14699For angle leg dimension from230 mm x 230 mm up to 260 mm x 260 mmWeight: 2,4 kg/eachPart No. 14700

With cable holder upon request

Mounting bracketFor refitting safety ladders to under-constructions made of round tube steel. Comeswith all installation elements. Support structuremust be checked for sufficient strength.

Galvanized steelWeight: 1,4 kg/eachPart No. 11222





B 9


06.2

006

Mounting bracketwith adjustable projections. Complete with allladder mounting elements. Wall attachmentmust be adapted to suit the structuralconditions. Min. dimensions M 16.

Galvanized steelWeight: 2,5 kg/each

L = 150 - 225 mmPart No. BB-VSTR 150-225

L = 225 - 300 mmPart No. BB-VSTR 225-300L = 300 - 375 mmPart No. BB-VSTR 300-375

Stainless steel, pickledWeight: 2,5 kg/each

L = 150 - 225 mmPart No. BB-VA4R 150-225

Greater projections upon request.


Fixing clampwith adjustable projection. Complete with allladder fixing elements. When ordering, pleaseindicate the exact mast diameter as well asthe projection span.

Weight: depends on mast diameter

Mast diameter: min. 60 mmMast diameter: max. 1500 mm

Galvanized steel

Projection spans:L = 200 - 275 mmL = 276 - 350 mm

Part No. BS-VSTR-<Ø in mm>




B 10


06.2

006

Adapterfor connection of mounting bracket 15563 andsteel ladder.



Weld-On bracketBecomes fixed to the structure by welding.Projection: 150 mm. Other projections up to280 mm max. upon request.

Untreated steel S235JRG2CWeight: 0,75 kg/eachPart No. 12732Galvanized steel S235JRG2CWeight: 0,75 kg/eachPart No. 16629


BracketFor use on tubular mast members of 20 - 70mm diameter. Made from galvanized steel.Comes with galvanized steel installationelements. Support structure must be checkedfor sufficient strength.





B 11


06.2

006

Mounting bracket with adapterwith adjustable projection. Suitable in area ofladder bends. Complete with all laddermounting elements. Wall attachment must beadapted to suit the structural conditions. Min.dimensions M 16.

Galvanized steelWeight: 3,0 kg/each

L = 220 - 295 mmPart No. BB-VSTAD 220-295L = 295 - 370 mmPart No. BB-VSTAD 295-370

L = 370 - 445 mmPart No. BB-VSTAD 370-445

Greater projections upon request.


Examples for the application




B 12


06.2

006

Mounting bracketfor inside diagonal struts of lattice towers.Please supply strut measurements.

Galvanized steelPart No. BB-DI


Mounting bracketfor outside diagonal struts of lattice towers.Please supply strut measurements.

Galvanized steelPart No. BB-DA

Mounting bracketfor diagonal crossings of lattice towers. Pleasesupply strut measurements.

Galvanized steelPart No. BB-DK




B 13


06.2

006


Mounting bracketFor installation on brickwork. (see chapterTB). Projection possible until 1000mm.Comes with installation elements for fixingladder to bracket. When ordering, pleasestate projection „L“.

Weight: depending on the projection.

Galvanized steelPart No. BB-MSTR-<projection in mm>Stainless steel, pickledPart No. BB-MA4R-<projection in mm>




B 14


06.2

006

Safety Ladders: Hot Dip Galvanized/Stainless SteelFootrests

Folding FootrestUnfolds to allow unrestricted climber access.Complete with fixings.


Stainless steel, pickledUpon request

Pivotable Footrestfor steel/stainless steel ladders. Comes withall installation elements.

Weight: 18 kg/each

Hinge on left sideGalvanized steelPart No. 16551Hinge on right sideGalvanized steelPart No. 16550

Stainless steel, pickled upon request.



B 15


06.2

006


Footrest with Two Working PlatformsTo provide working access adjacent to theladder, e. g. for working on offset antennasect. Footrest and platform unfold to allowunrestricted climber access. For use by oneperson only. For rung distance: 280 mm.Complete with fixings. Please specify mastdiameter.

Weight: Depends on mast diameter.Width 150 mm

Galvanized steelPart No. 15395

Stainless steel upon request.

Wall and corner mounting bracket onreqest.



B 16


06.2

006

Footrest with One Working Platform(on left side)To provide working access adjacent to theladder, e. g. for working on offset antennasect. Footrest and platform unfold to allowunrestricted climber access. For use by oneperson only. For rung distance: 280 mm.Complete with fixings. Please specify mastdiameter.

Weight: Depends on mast diameter.Width 150 mm


Stainless steel upon request


Footrest with One Working Platform(on right side)To provide working access adjacent to theladder, e. g. for working on offset antennasect. Footrest and platform unfold to allowunrestricted climber access. For use by oneperson only. For rung distance: 280 mm.Complete with fixings. Please specify mastdiameter.Weight: Depends on mast diameter.Width 150 mm


Stainless steel upon request





B 17


06.2

006

Cover Plate, steelFor Y-Spar steel ladder. Comes without laddersection. Prevents unauthorized people fromclimbing the ladder. Comes with padlock.Length: 2000 mm.

Weight: 16,0 kg/each

Cover Plate with handles for Y-Spar ladderGalvanized steelPart No. 11354

Cover Plate with handles for Twin-ladderGalvanized steelPart No. 17436

Cover Plate, aluminiumfor galvanized steel ladders. See page A 22.

The foldable ladder PivotLoc is also possibleas an alternative to the cover plate, pls. SeeA23.

Safety Ladders: Hot Dip Galvanized/Stainless SteelCover Plate



B 18


06.2

006

Safety Ladders: Hot Dip Galvanized/Stainless SteelCover Plate

Cover platefor Söll-steel ladders. Comes with laddersection. Prevents from unauthorized climbingof the ladder. Hinged on left side and securedby padlock.

Weight: 30,0 kg/each

With recess - Galvanized steelPart No. 22054

The foldable ladder PivotLoc is also possibleas an alternative to the cover plate, pls. SeeA23.



B 19


06.2

006

Safety Ladders: Hot Dip Galvanized/Stainless SteelRecess

RecessTo insert and take out the fall arrester. As thefall protection does not have any protectionfunction within the recess, there must be andend stop „below“ above the 2. notch above therecess. The end stop must be orderedseparately.

The recess may only be provided at thebeginning of the climbway.

At the beginning of climbway involving therisk of falling for the user, it is not allowedto utilize the recess.

In case the fall arrester will be taken outfrom the climbway during its course, thanan exit section has to be used.

At the time of ordering the part of theladder with recesses must be marked withan "A" or the notice "with recess".



B 20


06.2

006

Safety Ladders: Hot Dip Galvanized/Stainless SteelExit Section

Exit SectionUsed for secure removing/inserting the fallarrester from/into the guide-rail, e.g. onplatforms. See page B 19. Comes with fixingsand setting out/drilling jig to enable accurateinstallation. May be also refitted into alreadyexisting Söll steel ladders.



Factory assembly of the exit sectionAt the time of ordering, the part of the ladderwith the factory assemled exit section must bemarked with "AV" or the notice "with assemledexit section". In the case of assembly at thefactory please also specify the installationheight.

Please note:Installation is only possible between two rungs.

Possibility heights for installation in aladder section of 4480 mm

Height from bottom ladder section 560 mm between 2. and 3. rung 840 mm between 3. and 4. rung

1.120 mm between 4. and 5. rung 1.400 mm between 5. and 6. rung 1.680 mm between 6. and 7. rung 1.960 mm between 7. and 8. rung 2.240 mm between 8. and 9. rung 2.520 mm between 9. and 10. rung 2.800 mm between 10. and 11. rung 3.080 mm between 11. and 12. rung 3.360 mm between 12. and 13. rung 3.640 mm between 13. and 14. rung 3.920 mm between 14. and 15. rung

Recommended installing height aboveplatform: approx. 1.000 mm.



B 21


06.2

007

TurntableFor safe transfer from vertical to horizontal.Made of stainless steel plate and aluminiumrail section. Please specify the profile of thehorizontal and vertical guide-rail.

Stainless SteelWeight: 2,6 kg/each

Bending radius horizontal guide rail> 1000 mmPart No. 11607

Bending radius horizontal guide rail< 1000 mmPart No. 20349

Cost for mounting turntable onto a Y-Spargalvanized steelPart No. 16884

Safety Ladders: Hot Dip Galvanized/Stainless SteelAccessories

Ho-Ver turn tableFor safe change of travel direction fromvertical to horizontal to vertical travel. Thedirection of travel can only be changed to theleft or to the right. Available also with releaseoption in the pivoting part. Consult Sölltechnical support department for otherinstallation combinations.

Weight: 5,0kg per 1 unit

Stainless steel pickledPart No. 22322Release option (without illustration).Part No. 22495



B 22


06.2

006

Mounting bracket with adjustableprojectionProjection: 120 mm up to 160 mm. Comeswith all installation elements. To be used formounting turntable Part No. 11607 only.




Mounting bracket with adjustableprojectionProjection: 160 mm up to 200 mm. Comeswith all installation elements. To be used formounting turntable Part No. 11607 only.






B 23


06.2

006


Shaft entering deviceFor safe entry into manholes. The device isinserted into the female coupling on the top ofthe guide-rail in the manhole. This device canbe moved from one manhole ladder to another.


Female Coupling for Shaft Entering DeviceThis device is fixed to the top of the guide-railin the manhole.




B 24


06.2

006

Rotary Exit SectionUsed for leaving the top end of the laddersystem by inserting the fall arrester into therotary and turning either side safely onto theplatform behind the ladder. Please specifytotal ladder length up to the rotary disk. Seepage B 24. Made of anodized aluminium alloy.

With footrest (independently pivotableplatforms)Weight: 16,9 kg/eachPart No. 17053

Without footrestWeight: 12,5 kg/eachPart No. 16666

Cost for mounting rotary exit section onto avertical Söll Aluminium ladder by Söll.Part No. 16604

Safety Ladders: Hot Dip Galvanized/Stainless SteelRotary Exit Section



B 25


06.2

006

Pivoting roof exitTo be used in confined spaces. For a safetransfer to a surface behind the climbingway. Anchoring on the left side. Completewith all fixing elements. To be fixed on thecentral spar of the hot dop galvanized/stainless steel ladder. (Pls. See page B 27b).


Safety Ladders: Hot Dip Galvanized/Stainless SteelPivoting roof exit



B 26


06.2

006

Twisted Change over railGuide rail with 90° bend allows transfer fromvertical to horizontal direction. To be usedonly with fall arrester Compact/Comfortor Söll-Fall arresters, which have beenincluded into the delivery programme afterMarch 2003. Length of guide rail: 2240 mm.The guide rail is also turned 90° in the area ofthe bend so that in the horizontal area the leadis towards the side. A mounting is required forthis area (not part of scope of supply). Suppliedcomplete with joining piece, fixing cross andtop end stop.

Clockwise turn

Hot Dip Galvanized SteelPart No. 16315

Stainless steel, pickledPart No. 22311

Anti-clockwise turnMust be not used in connection with a turntable!

Hot Dip Galvanized SteelPart No. 16292Stainless steel, pickledPart No. 22310

Safety Ladders: Hot Dip Galvanized/Stainless SteelTwisted change over rail



B 27


06.2

006

Safety Ladders: Hot Dip Galvanized/Stainless SteelTwisted change over rail

Support strutFor supporting a twisted change over rail.Complete with rail attachment screws. Maxi-mum height 1370 mm.

Hot Dip Galvanized SteelPart No. 17509

Explanation:When used combined with the change overrail (Part No. 16315/16292), the 1.096 mmsupport has to be ordered.

Reinforcement/StrengtheningIs required, when the distance between lastmounting point and top-end of the ladder/railexceeds 380 mm. It must be bolted onto theguide-rail at a distance of 560 mm and mustextend down over at least two mountingbrackets. Square tube 50x30x3 mm. See pageB 4. Comes with all installation elements.

Galvanized steelWeight: 3,3 per metrePart No. HV-ST-<length in mm>

Stainless steel, pickledWeight: 3,3 per metrePart No. HV-A4-<length in mm>



B 28


06.2

006

RoundaboutFor a safe transfer between two differentvertical climbing routes without disconnectingthe fall arrester from the guide-rail or theclimber. Minimum mast diameter: 200 mm,Maximum mast diameter: 1000 mm.Comprising two horizontal rods which enablesthe transfer of the guide-rail section togetherwith the fall arrester to the other ladder. Madeof galvanized steel with aluminium guide-railsection. Comes with all fixing elements. Foradded safety and ease of movement, werecommend fitting a hand-rail section (PartNo. HL) and an open steel flooring transferplatform (Part No. UP). Please specify mastdiameter, offset angle, projection and laddertype.

Weight: depending on dimensions, approx.25 kg.

For mast diameter from 200 to 350 mmPart No. 16352For mast diameter from 351 to 500 mmPart No. 18700For mast diameter from 501 to 700 mmPart No. 18701For mast diameter from 701 to 1000 mmPart No. 18702

Safety Ladders: Hot Dip Glavanized/Stainlees SteelAccessories

Installation exampleRoundabout with hand rail and transferplatform.

Roundabouts for climbing ways withspecial projections are available uponrequest.



B 29


06.2

006


HandrailIdeal for use with roundabout. Can also beused on its own. Minimum mast diameter: 90mm. Made of galvanized steel. Complete withmounting elements. Please specify mastdiameter and offset angle.

Weight: depending on dimensionsPart No. HL-<segment size>-<Ø in mm>

It is not considered as an anchoragepoint according EN standard 795.

Transfer PlatformIdeal for use with roundabout. Can also beused on its own. Minimum mast diameter: 100mm. Made of galvanized steel. Complete withmounting elements. Please specify mastdiameter and offset angle.

Weight: depending on dimensionsPart No. UP-<segment size>-<Ø in mm>



B 30


06.2

006

Identification platefor Fall Protection Systems - Climbing Ladders.Cover plate assembled in factory.

Part No. 19876 not graved

engraved

Part No. Denomination 20885 Y-Spar Galvanized Steel 20886 Y-Spar Stainless Steel

20889 Y-Spar Galvanized Steel with anti-slipping rungs

20890 Y-Spar Stainless Steel with anti-slipping rungs


Safety Ladders: Hot Dip Galvanized/Stainless Steel · Part No. BS-STR- Stainless steel, pickled...

Documents

Transcript of Safety Ladders: Hot Dip Galvanized/Stainless Steel · Part No. BS-STR- Stainless steel, pickled...