Saab 9-3 4D/5D M03 ......The Tele1 connection is located adjacent to the lower edge of the centre...
Transcript of Saab 9-3 4D/5D M03 ......The Tele1 connection is located adjacent to the lower edge of the centre...
900Installation instructionsSCdefault
MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE
SITdefault
Saab 9-3 4D/5D M03-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3Saab 9-5 M01- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17Handsfree kit, mobile phone
Accessories Part No. Group Date Instruction Part No. Replaces
32 025 90732 026 144 9:89-31 May 07 32 025 872 Nov 06
F930A592
2 32 025 872
F930A488
1x 1x 1x
1x
1x1x
11x
32 025 872 3
Saab 9-3 4D/5D M03-
Saab 9-3 4D/5D M03-
1 Ignition in OFF position.2 Remove the floor console’s right-hand side
piece. 3 Remove the lower glove box screws.4 Remove the inner glove box screws.
F930A491
3
F930A489
1
F930A490
2
C
A
B
B
F930A492
4
4 32 025 872
Saab 9-3 4D/5D M03-
5 Unplug the connector for the glove box lighting(A). Cars with ACC: Remove the coolant hose fromthe glove box (B).
6 Remove the cover plate from the A-pillar trim. 7 Remove the retaining screw.8 Grip the upper edge of the A-pillar trim and care-
fully pull out and up.
7
F930A495
F930A493
5
AB
F930A494
6
F930A496
8
32 025 872 5
Saab 9-3 4D/5D M03-
9 Remove the rear cover. 10 Remove the front cover. 11 Remove the screws. 12 Remove the centre cover.
F930A499
11
F930A497
9
F930A498
10
F930A500
12
6 32 025 872
Saab 9-3 4D/5D M03-
13 Cars with rain sensor: Remove the cover.14 Fit the adhesive tape onto the microphone.15 Fit the microphone.16 Insert the microphone cable through the hole in
the headlining by the roof console.
F930A503
15
F930A501
13
F930A502
14
F930A504
16
32 025 872 7
Saab 9-3 4D/5D M03-
17 Route the microphone cable on under the head-lining towards the windscreen. Press in the cen-tre cover and draw the microphone cable tight atthe same time.
18 Route the microphone cable under the headlin-ing.
19 Secure the microphone cable to the A-pillar.20 Route the microphone cable under the panel,
and on to the centre console and secure it.
ImportantSecure the wiring harness firmly so that there is norisk of chafing and rattling.
F930A507
19
F930A505
17
F930A506
18
F930A508
20
8 32 025 872
Saab 9-3 4D/5D M03-
Fit the keypad in accordance with one of the alterna-tives.
F930A509
22.1-22.5
21.1-21.7
32 025 872 9
Saab 9-3 4D/5D M03-
21 Fitting the keypad, alternative 1: 21.1 Remove the ashtray/storage compart-
ment.21.2 Remove the ACC panel.21.3 Fit the keypad to the console and mark out
the cable route. 21.4 Cut out from the console for the cable.
F930A513
21.3
F930A511
A
21.1
B
F930A512
BA
21.2
F930A514
21.4
10 32 025 872
Saab 9-3 4D/5D M03-
21.5 Fit the keypad to the console.21.6 Route the cable down behind the radio
down towards the air bellows and secure it.
21.7 Fit the ACC panel (A). Check that the key-pad’s cable is located in the groove. Fit theashtray/storage compartment (B).
ImportantSecure the wiring harness firmly so that there is norisk of chafing and rattling.
F930A516
A
B
21.7
F930A515
21.5
F930A517
21.6
32 025 872 11
Saab 9-3 4D/5D M03-
22 Fitting the keypad, alternative 2: 22.1 Remove the cover. 22.2 Route the cable along the right-hand side,
down towards the air bellows.22.3 Route the cable in the dashboard’s groove. 22.4 Fit the cover.
F930A520
22.3
F930A518
A
B
22.1
F930A519
22.2
22.4
F930A521
A
B
12 32 025 872
Saab 9-3 4D/5D M03-
22.5 Fit the keypad and adjust any excess cablelength.
23 Connect the control module (A), microphone (B)and keypad (C) to the adapter harness.
24 Secure the control module using two cable tiesto the panel member.
25 Release the Tele1 connection from the car’scable harness by cutting the tape. The Tele1connection is located adjacent to the lower edgeof the centre console on the right-hand side.
F930A524
24
F930A522
22.5
F930A523
23
A B C
F930A525
25
32 025 872 13
Saab 9-3 4D/5D M03-
26 Connect the adapter harness to the car’s Tel 1connection and secure the wiring.
27 Secure the wiring to the panel member.
28 Cars with rain sensor: Fit the cover.29 Fit the screws to the cover.
ImportantSecure the wiring harness firmly so that there is norisk of chafing and rattling.
F930A527
26
F930A528
27
F930A529
28
F930A530
29
14 32 025 872
Saab 9-3 4D/5D M03-
30 Fit the front cover. 31 Fit the rear cover.32 Align the A-pillar trim in position. Take care not
to damage the inflatable curtain.
33 Fit the retaining screw.Tightening torque: 5 Nm (4 lbf ft).
WARNINGTake care not to damage the inflatable curtain.Damage could result in the inflatable curtain notproviding the intended protection to the occupantsin the event of a collision.
F930A533
32
F930A531
30
F930A532
31
F930A534
5Nm(4lbf ft)
33
32 025 872 15
Saab 9-3 4D/5D M03-
34 Fit the cover plate to the A-pillar trim. 35 Plug in the connector for the glove box lighting
(A). Cars with ACC: Fit the coolant hose for theglove box (B).
36 Fit the inner glove box screws.37 Fit the lower glove box screws.
F930A537
36
F930A535
34
F930A536
35
AB
F930A538
37
16 32 025 872
Saab 9-3 4D/5D M03-
38 Fit the floor console’s right-hand side piece.
F930A539
38
A
C
B
32 025 872 17
Saab 9-5 M01-
Saab 9-5 M01-
1 Ignition in OFF position.2 Remove the radio/navigation unit, M01-05:
2.1 Insert the special tools into the intendedholes until the tools engage and pull outthe unit.
2.2 Remove the compartment.2.3 Unplug the connectors.
E930A429
M01-052.2
E930A427
1
E930A428
M01-052.1 A
B
CLICK
E930A430
M01-052.3
18 32 025 872
Saab 9-5 M01-
3 Remove the radio/navigation unit, M06- 3.1 Remove the plugs and remove the screws.3.2 Pull the unit out and unplug the connectors
and disconnect the antenna connection.4 Remove the ACC panel.
E930A433
4 A
B
3.1
E930A431
M06-
E930A432
M06-3.2
32 025 872 19
Saab 9-5 M01-
5 Remove the lower section of the dashboard onthe driver’s side: 5.1 Remove the data link connector (A)5.2 Remove the lower panel (B).5.3 Remove the clip (C).5.4 Remove the floor lighting (D).
E930A434
C
B
B
A
D
B
5
20 32 025 872
Saab 9-5 M01-
6 Remove the cover to the fuses. 7 Remove the A-pillar trim (secured with clips).
Remove the upper clip (A) from the trim.
8 Remove the sun visor’s screws and allow thesun visor to hang down.
9 Remove the glass cover (A), the retaining screw(B) and lower the cover.
WARNINGTake care not to damage or loosen the energyabsorbers. Damaged or loosened energy absorb-ers must not be refitted. In appropriate cases, thewhole of the headlining must be replaced. A dam-aged energy absorber could provide reduced pro-tection to the head in the event of impact.
E930A437
8
E930A435
6
E930A436
7 A
E930A438
9
BA
32 025 872 21
Saab 9-5 M01-
10 Fit the adhesive tape to the microphone. 11 Press the microphone in on the outside of the
cover, beside the car’s original microphone.12 Route the microphone cable up, under the
headlining and on, down around the A-pillar. 13 Secure the microphone cable up against the
existing cable ties.
E930A441
12
E930A439
10
E930A440
11
E930A442
13
22 32 025 872
Saab 9-5 M01-
14 Press the cover in, fit the retaining screw (B) andthe glass cover (A).
E930A443
14
A
B
32 025 872 23
Saab 9-5 M01-
15 Route and secure the microphone cable: Route the cable under the panel, towards thecentre console and in behind the radio/naviga-tion unit Secure the cable under the panel.
ImportantSecure the wiring harness firmly so that there is norisk of chafing and rattling.
E930A444
24 32 025 872
Saab 9-5 M01-
16 Remove the cover for the heating and ventila-tion unit.
17 Fold aside the floor carpet.18 Cars with diesel engine:
18.1 Remove the sound absorber.18.2 Cut out the top insulation layer.
E930A448
18.1
E930A446
16
E930A447
17
E930A445
18.2
32 025 872 25
Saab 9-5 M01-
19 Position the adapter harness. 20 Connect the control module to the adapter har-
ness.21 Align the control module and secure the wiring.
22 Cars with diesel engine: Fit the soundabsorber.
ImportantSecure the wiring harness firmly so that there is norisk of chafing and rattling.
E930A451
21
E930A449
19
E930A450
20
E930A452
22
26 32 025 872
Saab 9-5 M01-
23 Refit the floor carpet. 24 Fit the cover for the heating and ventilation unit.25 Cut the tape around the Tele1 connection on the
car’s wiring harness. 26 Connect the adapter harness to the car’s Tele1
connection.
E930A455
25
E930A453
23
E930A454
24
E930A456
26
32 025 872 27
Saab 9-5 M01-
27 Connect the adapter harnesses.
E930A457
27
28 32 025 872
Saab 9-5 M01-
Fit the keypad in accordance with one of the alterna-tives.
E930A458
29.1-29.4
28.1-28.14
32 025 872 29
Saab 9-5 M01-
28 Fitting the keypad, alternative 1:
28.1 Remove the storage compartment (A).28.2 Automatic transmission: Remove the
surround (B).28.3 Manual gearbox: Lift up the gear lever
gaiter (C).28.4 Remove the cover’s screws (D) and
unplug the connector (E).
ImportantThis location is not an option for cars equippedwith ashtray, as the ashtray would come into con-tact with the keypad when extended.
28.1-28.4
E930A460
A A
B
C
D
E
30 32 025 872
Saab 9-5 M01-
28.5 Measure out the keypad location and drill a3 mm hole.
28.6 Cut/drill a groove straight out. 28.7 Connect the keypad to the adapter har-
ness.28.8 Secure the wiring.
E930A463
28.7
E930A461
30mm(1.2in)
3mm (0.1in)
20mm(0.8in)
28.5
E930A462
28.6
E930A459
28.8
32 025 872 31
Saab 9-5 M01-
28.9 Plug in the connector (E) and fit the cover’sscrews (D).
28.10Manual gearbox: Fit the gear lever gaiter(C).
28.1128.12Fit the storage compartment (A).
E930A464
A A
B
C
D
E
28.9-28.12
32 32 025 872
Saab 9-5 M01-
28.13Secure the keypad’s wiring harness.
28.14Fit the keypad.
ImportantSecure the wiring harness firmly so that there is norisk of chafing and rattling.
E930A465
28.13
E930A466
28.14
32 025 872 33
Saab 9-5 M01-
29 Fitting the keypad, alternative 2: 29.1 Carefully prize out the switch panel and
route the keypad cable between the switchpanel and the dashboard.
29.2 Fit the keypad.29.3 Connect the keypad to the adapter har-
ness.29.4 Secure the wiring.
E930A469
29.3
E930A467
29.1
E930A468
29.2
E930A470
29.4
34 32 025 872
Saab 9-5 M01-
30 Secure the wiring together with the car’s wiringharness.
31 Fit the sun visor’s screws.32 Fit the lower section of the trim in place, fit the
clip (A) with the loop down in the trim and pressthe trim into all of the clips.
33 Fit the cover to the fuses.
ImportantSecure the wiring harness firmly so that there is norisk of chafing and rattling.
WARNINGTake care not to damage or loosen the energyabsorbers. Damaged or loosened energy absorb-ers must not be refitted. In appropriate cases, thewhole of the headlining must be replaced. A dam-aged energy absorber could provide reduced pro-tection to the head in the event of impact.
E930A473
32 A
E930A471
30
E930A472
31
E930A474
33
32 025 872 35
Saab 9-5 M01-
34 Fit the lower section of the dashboard: 34.1 Connect the floor lighting (D).34.2 Fit the clip (C).34.3 Fit the lower panel (B).34.4 Fit the data link connector (A)
E930A475
C
B
B
A
D
B
34
36 32 025 872
Saab 9-5 M01-
35 Fit the ACC panel. 36 Fit the radio/navigation unit, M01-05:
36.1 Plug in the connectors.36.2 Fit the compartment.36.3 Insert the unit.
36.2
E930A478
M01-05
E930A476
35
E930A477
M01-0536.1
E930A479
M01-0536.3
32 025 872 37
Saab 9-5 M01-
37 Fit the radio/navigation unit, M06- 37.1 Plug in the connectors.37.2 Insert the unit, fit the screws and the plugs.
E930A480
M06-37.1 37.2
E930A481
M06-