S700 Bike Computer User Manual - cyrusher.com · P04: Bike Auto Shutting-down Time Setting...

Cyrusher Sports Team

www.cyrusher.com

[email protected]

1 / 27

S700 Bike Computer User Manual

This bike computer user manual is only for Cyrusher XF500,Extrbici XF660 1000W, Cyrusher

XF690, Cyrusher XF770, Lankeleisi XT750,Lankeleisi G550,Lankeleisi T8 and Lankeleisi XT750

plus operations setting reference.

If you are using other Cyrusher or Lankeleisi Ebikes models, please contact Cyrusher Sports

Team for help.

Bike Computer Screen:

Technical Symbol Definition：

http://www.cyrusher.com/

mailto:[email protected]


www.cyrusher.com

[email protected]

2 / 27

AVG: Average Speed

MAX: Max. Speed

Speed: Real Time Speed

DST: Driving Mileage (Estimated how far you can drive based on the current battery capacity)

Front Light

Walk Mode/ Cruise Control/ Pedal Assistant Power Level and Number

Battery Remains

TRIP: Single Odometer

ODO: Total Odometer

TM: Bike Computer Working /Cycling Time ( it tells many hours the bike computer has started




www.cyrusher.com

[email protected]

3 / 27

for working)

ERR: Error Code

Operation Setting：

In default setting of S700 bike computer:

⚫ Please note that PAS 0 means only throttle works;

⚫ PAS 1-5 means only Pedal assistant works but throttle does not work.

1. Turn on/ Turn off bike computer: Press for seconds to turn or turn off the

bike computer;

2. Turn on/ Turn off bike front light: After turning on the bike computer and press

for 3 seconds to turn on or turn off front light.

3. Active walk mode(Optional) : After turning on the bike computer and press

for 3 seconds to active the walk mode

4. Increase/ Decrease PAS Level: After turning on the bike computer and press

to increase the PAS Level and Press to decrease PAS level.

5. ODO/TRIP/ERR/TIME Checking: After turning on the bike computer and press

one time to switch and check data of ODO/TRIP/ERR/TIME. (Images Below)




www.cyrusher.com

[email protected]

4 / 27

6. Enter Setting Mode: After turning on the bike computer and press

and together for 3 seconds to enter setting mode,

Then press to switch P level setting from P01 to P18

and press or to choose the right data code for each P level

setting.




www.cyrusher.com

[email protected]

5 / 27

7. Speed/AVG/Max Checking: After turning the bike computer, press +

for 3 seconds to switch and check data of Speed/AVG/Max.( Images Below)

P Level Setting Code Definition：

P01: Brightness Setting,

Range：1-3, 1 is darkest, 3 is brightest;

P02: Speed Unit Setting ( How to change the Speed Unit to Miles or KMS ?)

Range: 0-1; 0 is KM, 1 is Mile

In the setting modes, change the P02 code from 00000 to 00001 by press or

the speed unit will be in Miles/H;




www.cyrusher.com

[email protected]

6 / 27

P03: Working Voltage Setting,

Range: 24V,36V, 48V;

P04: Bike Auto Shutting-down Time Setting

Range：1-60

It means if you do not operate the bike computer or use the e-bike within the minutes range

from 1 to 60 minutes, the bike computer will shut down automatically;

P05: PAS Preference Setting

Range:

0 ---only shows 1-3 levels;

1 ----shows 1-5 levels;

2----shows 1-9 levels;

Just PAS level number are different, but top and lowest level power is the same, such as 3=

5=9 in different working modes;

P06: Wheel/rim diameter Setting (Inch)

Range: 20/22/26/28 (Normally, if 20 inch rim, setting number will be 22inch)

P07: Speed Monitor Setting,

Range: 1-100;

This technical setting is only for engineer setting, do not modify or change the setting.




www.cyrusher.com

[email protected]

7 / 27

P08: Speed Limit Setting.

Range: 1-100KM;

If setting data is 100KM,which means there is no speed limit, however, the real speed limit of

e-bike is controlled by motor and controller. You can only set the bike computer speed limit

within the given the range fixed by motor and controller. For example, if the motor and

controller fixed top speed limit is at 40KM/H, you can only set lower top limit such as 35KM/H,

then the e-bike will keep run within the top speed limit-- 35KM/H; If you set 50KM/H, the

real top speed limit is only 40KM/H;

P09: Zero boost or Non-Zero Boost Setting.

Range: 0 means zero boost; 1 means non zero boost.

In the zero boost also called hard boost which means, once you use the throttle or pedal

assistant, you get will push from the motor immediately; In non-zero boost, you have to use

pedal first to move the e-bike to some certain speed and the throttle or PAS will be active.

P10: Driving Modes Setting;

Range:

0 – PAS only, the throttle is not working;

1—throttle only, PAS is not working；

2—both throttle and PAS are working;

P11: PAS Sensitivity Setting

Range: 1-24,


P12: PAS Strength Setting

Range: 1-5,


P13: PAS Magnetic Sensor Setting

Range: 5/ 8/12


P14: Controller Max Current Limit Setting

Range: 1-20A;




www.cyrusher.com

[email protected]

8 / 27

P15: Controller Low voltage Setting.

Range: N/A,

Need to check with controller technical data sheet for reference;

P16: ODO, Total Odometer Clearance Setting

In setting mode, press for 5 seconds in setting mode, you can change and clear

the current total odometer to Zero.

P17: N/V

Range: 100（default）


P18: Bike Computer Reset Setting

In setting mode, press for 5 seconds in setting mode, reset the bike computer in

the bike computer default setting ONLY(not the e-bike) once SSSS shows on LCD.

.




www.cyrusher.com

[email protected]

9 / 27

Please note that the default setting is only for S700 bike computer itself and it is not same

default setting for each mode of electric bike. For example, although XF500 and XF770 are

using the same bike computer, however, their default setting number maybe different at the

same P Levels setting.

Error Codes：

Range/Problem/Solution：

00000--- Normal

00006---Low Battery Voltage---Need charge battery;

00007---Motor Failure---Check motor cable connection whether loose or damage;

00008---Throttle Failure—Check throttle cable connection whether loose or damage;

00009---Controller Failure—Check controller cable connection whether loose or damage or

incorrect connection;

00010---Data Receiving Failure—Check bike computer connection whether loose or damage

00011---Data Sending Failure—Check bike computer connection whether loose or damage;

Default Bike Computer Setting for XF770 Only (Images Below)

Other Models of e-bikes Default Setting are different in P06 as following:

XF500/G550---P06—22 inch;

T8/XF770/XT750---P06—26 inch;

XF660-1000W/XF690/XT750 Plus ---P06---28inch;




www.cyrusher.com

[email protected]

10 / 27




www.cyrusher.com

[email protected]

11 / 27




www.cyrusher.com

[email protected]

12 / 27




www.cyrusher.com

[email protected]

13 / 27




www.cyrusher.com

[email protected]

14 / 27




www.cyrusher.com

[email protected]

15 / 27




www.cyrusher.com

[email protected]

16 / 27




www.cyrusher.com

[email protected]

17 / 27




www.cyrusher.com

[email protected]

18 / 27




www.cyrusher.com

[email protected]

19 / 27




www.cyrusher.com

[email protected]

20 / 27




www.cyrusher.com

[email protected]

21 / 27




www.cyrusher.com

[email protected]

22 / 27




www.cyrusher.com

[email protected]

23 / 27




www.cyrusher.com

[email protected]

24 / 27




www.cyrusher.com

[email protected]

25 / 27




www.cyrusher.com

[email protected]

26 / 27




www.cyrusher.com

[email protected]

27 / 27



S700 Bike Computer User Manual - cyrusher.com · P04: Bike Auto Shutting-down Time Setting...

Documents

Transcript of S700 Bike Computer User Manual - cyrusher.com · P04: Bike Auto Shutting-down Time Setting...