S3 SUPER SLICER - DewEze · 2019-11-13 · S3 Statement of Warranty Harper Industries, Inc. (HII)...
Transcript of S3 SUPER SLICER - DewEze · 2019-11-13 · S3 Statement of Warranty Harper Industries, Inc. (HII)...
-
S3
S3 SUPER SLICER
3-2020
OPERATOR’S & PARTSMANUAL
-
S31
-
S3
Thank you for purchasing a Deweze S3
TO THE OWNER OR OPERATOR:
As with all Harper products, the S3s have been thoroughly tested and built to provide a sturdy, de-pendable product. The S3 is equipped with hydraulics, which allows it to be used for a wide range of lifting and hauling tasks. This manual is written as an aid to operating and maintaining the DewEze S3. Read and understand the manual thoroughly before operation to avoid damage to the unit or injury to the operator or bystanders.
A S3 can present hazards to an operator who follows unsafe procedures in either the operation or maintenance of the unit. Therefore, SAFETY WARNINGS are present at certain locations in the text. Harper Industries is not responsible for accidents or injuries that result from the misuse or lack of maintenance of the S3.
SYMBOL: SAFETY WARNING!
MEANING: Failure to understand and obey this warning may result in injury to you or others. Whenever this symbol is used, please pay very close attention to the information presented, and make sure you fully understand. If you do not, contact your dealer or Harper Industries for clarifica-tion.
151 E. HWY. 160 Harper, KS 67058(620) 896-7381 • Fax (620) 896-7129
Toll Free 800-835-1042Email [email protected]
Website www.deweze.com
© 2019 Harper Industries, Inc.The Harper and DewEze names are registered trademarks of Harper Industries, Inc. All other brand and productnames are trade-
marks or registered trademarks of their respective companies.
1
-
S3
Statement of Warranty
Harper Industries, Inc. (HII) warrants to each purchaser of a new DewEze S3 from an authorized dealer or representative, that such equipment is free of manufacturer’s defects in workmanship and materials which appear while in normal service for a period of ONE YEAR commencing with delivery to the original user.
The obligation of HII under this warranty is expressly limited, at our option, to replacement or repair at a service facility designated by Harper Industries or at the manufacturing plant in Harper, KS. A part will be replaced after inspection discloses it to have been defective. This warranty does not apply to defects caused by damage or unreasonable use (includ-ing failure to provide reasonable and necessary maintenance, or by performing functions without genuine DewEze S3 accessories) while in the possession of the consumer.
Warranty is limited to parts, labor and ground freight delivery of replacement parts. HII shall not be liable for the consequential damages of any kind, including but not limited to consequential labor costs or transportation charges in connection with replacement or repair of defective parts.
This warranty does not apply to parts subjected to misuse, abuse, alteration, improper or inadequate maintenance, or normal wear (including belts, chains, sickles).
Harper Industries makes no warranty with respect to trade accessories. They are subject to the warranties of their respective manufacturers.
ANY IMPLIED OR STATUTORY WARRANTIES, INCLUDING ANY WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. HII makes no other ex-press warranty, nor is anyone authorized to make any on behalf of HII.
For further information please contact your nearest DewEze S3 dealer.
RECORDSDate of Purchase ______ / ______ / ______
Dealer’s Name _________________________________ Dealer’s Phone _________________________________ Serial Number Machine __________________________
2 3
-
S3
Table of ContentsOPERATOR SECTIONTo the Owner or Operator...............................................Warranty Statement........................................................Table of Contents............................................................Specifications..................................................................Safety Guidelines............................................................Set-Up Instructions.........................................................Operation Hydraulic Requirements................................... Loading Instructions.......................................... Feeding Instructions.........................................Adjustments Feed Rate......................................................... Flow Control Valve Adjustments.......................Maintenance Schedule....................................................
PARTS SECTION Table and Feed Chain...................................... Trailer Assembly............................................... Backboard and Sides....................................... Safety Shields................................................... Sickle Height Adjustment.................................. Twine Box - Optional......................................... Decals...............................................................
Sickle Drive Assembly...................................... PTO Kit............................................................. Hydraulic Option............................................... Hydraulic Option Schematic.............................
3
123456
788
89
10
1.11.21.31.41.51.61.7
2.12.22.32.4
-
S3
Specifications
4 5
Power Hydraulic or PTO poweredDimensions 91.63” H x 148” L x 119” W (in field position)Weight 2750 lbs. w/ trailerCutting Device 81” Sickle Bar - 27 individual sickle sections (knives)Shipping Width 91.63” H x 148” L 102.0” WTire Pressure 35 psi cold
NOTE: Following publication of this manual, certain changes in standard equipment and options may have occurred which would not be included in these pages. Your Harper dealer is the best source for up-to-date information.
-
S3
Safety Guidelines
• Use genuine factory parts or parts with equivalent characteristics, includ- ing type, strength and material. Fail- ure to do so may result in product mal- function and possible injury to the op- erator and/or others.• If hardware is not secure, or if some of the hardware is over-tightened, equip- ment failure may result, posing poss- ible safety hazards.• To prevent possible eye injury, always wear SAFETY GLASSES while oper- ating equipment.• Replace locknuts and locking screws if you can tighten them without feeling considerable resistance for several turns before they are completely tight. Replace them with factory authorized parts or their equivalent.
Guards & Shields• Keep all safety devices in place.• Replace all worn, damaged, unusable, missing or lost safety shields and guards before operating the equip- ment.• Keep the equipment in good operating condition.• Table safety stops have been provided by the manufacturer and we do not recommend removing them for any reason. See parts page 1.5.
Safety Decals• If safety related or instructional decals become illegible or are removed, re- place them immediately. New decals may be obtained from your local Harp- er Dealer.• If you replace parts that have such decals attached to them, make sure the decals are replaced with current versions, and are on the replacement parts before the machine is operated again.
HydraulicsTo prevent serious injury or death:• Relieve pressure on system before repairing, adjusting or disconnecting any hydraulic hose or fitting.• Wear proper hand and eye protection when searching for leaks.• Use wood or cardboard instead of hands when looking for leaks.• Keep all hoses, fittings and compo- nents in good operating condition.• Do not use any type of heat or flame (welding, soldering, cutting torch, etc.) near pressurized hydraulic lines.
SAFETY WARNING!HIGH-PRESSURE FLUID HAZARD!Escaping fluid under pressure can pene-trate skin causing serious injury or death.
5
-
S3
Set-Up Instructions
Your S3 is shipped from the factory in a “knocked-down” position to make it easier to transport. If it is necessary for you to trans-port your S3 you will again need to “knock it down” in order to get within the legal limits of most public roads. If transport is necessary or if you have received your machine in the “knocked-down” position follow the instruc-tions below to set it up correctly.
1. Raise the backboard (1) into an up- right position and secure loosely with two 1/2” bolts (5) provided on each end. (See Fig. 1)
2. Set sides (2) in place and fasten down with five 5/16” bolts (3) located on the table sides.
3. Tighten top hold-down brackets (4). (See Fig. 1).
4. Tighten four 1/2” bolts described in instruction 1 above.
5. Slide table into feeding position (fig 3) and secure with bolts. The feeding position is marked on the underside of the table with bolt hole slots. The slots are located on the trailer on the angle iron rails the table is sitting on. The feeding position bolt hole slots are on the feed of the slicer. They are shown in figures 4 & 5.
SAFETY WARNING!OPERATING THE S3 LIFTING ARM WITH THE TABLE IN THE ROAD/TRANSPORT POSITION WILL DO DAMAGE TO THE LIFT ARM LINKAGE!
6 7
Fig. 1
1
2
3
4
5
Fig. 2
Fig. 3
Feed Position
Transport Position
-
S3
Fig. 4
Fig. 5
For PTO machines we have installed a PTO stand for your convenience. It also contains key slots for your hydraulic hoses. The PTO shaft rests in the cutout on top of the stand and the hydraulic hoses insert into the key slots. When using S3, be sure PTO stand is in down (working) posi- tion. Do so by pulling pin and pushing down. Then reinstall pin.
Operation
NOTE: BEFORE OPERATING YOUR NEW S3 MAKE A COMPLETE INSPECTION OF ALL COMPONENTS TO INSURE THAT ALL THE NUTS AND BOLTS ARE TIGHT AND THAT NO DAMAGE HAS OCCURRED DUR-ING SHIPPING.
HYDRAULIC REQUIREMENTSYour new DEWEZE S3 is designed to be used as a mobile feeding unit mounted on a trailer or as a stationary unit in a permanent installation. Regardless of the type of use the S3 WILL REQUIRE 15 GPM (gallons per minute) of hydraulic oil flow and a minimum of 1800 PSI (pounds per square inch) hy-draulic pressure to operate properly. Be sure that the hydraulic system you intend to use is functioning properly and that the oil is clean and of good quality.
Two hydraulic remotes are required to oper-ate the trailer mounted S3. One is to control the lift arm for loading the bales and the other is to operate the slicer table. Each remote must be capable of reversible flow. You may want to mark the remotes to make sure that you hook up the hydraulics the same way each time you use the machine.
NOTE: When using a hydraulically driven S3 III continuously (for more than 3 bales in 10 minutes) the following adjustments must be made to tractors equipped with a high flow, pressure compensated loadsense hydraulic system.
7
Pin
-
S3
LOADING INSTRUCTIONS (Trailer Mounted Unit Only)
Approach the bale on its right side with the lift arm lowered to the ground. Cradle the bale in the lift fork by moving forward so that the bale is against the back of the fork. Lift the bale all the way up so that the bale rolls onto the table slats. Move the bale toward the sickle by activating the feeder and stop as the bale reaches the sickle. To load and carry a second bale, repeat the above process and raise the second bale until it rests snuggly against the first.
NOTE: Be sure to raise the lift arm to the upright position and latch the safety chain whenever you transport your S3 on the road!
FEEDING INSTRUCTIONS
To engage the feeding operation of the S3, idle the tractor engine, engage the slicer table hydraulics and increase the engine speed to the tractor manufacturer’s suggested rated speed. On a PTO slicer the PTO RPM is 540. To engage the PTO we recommend idling the engine, engaging the PTO then accelerating the tractor’s engine to rated speed for correct 540 PTO RPM operation.
SAFETY WARNING!Stay clear of the table and cutter bar when the machine is in operation!
If the system stalls, reverse the slats and try again. If stalling continues, increase the RPMs of the tractor about 10 percent.
NOTE: Always wait until the first bale has been processed completely and the table slats have stopped before loading the second bale onto the table.
8 9
1. Flow (speed) must be controlled on the tractor remote outlet. To set this speed first set the Slicer flow as outlined in the manual. Secondly, turn the flow control toward the “turtle” on the tractor selective control outlet until the speed begins to decrease. Stop turning as soon as you can notice a decrease in speed. Failure to follow these procedures may result in the overheating of the tractor hydraulic system, as the system will be at maximum flow and pressure. (Load is sensed at the tractor selective control valve and if this valve is wide open the system is at constant maximum pressure / flow.
2. The alternative to the above is to buy a “flow limiter valve” and attach it between the quick disconnect and the hose on the pressure side.
3. On PTO model S3 III, flow must also be regulated at the selective control outlet for the slat motor.
NOTE: If the above instructions are not fol-lowed, the following symptoms may develop:
Rapid heating of the tractor hydraulic oil, this will show up as a loss of speed on the hydraulic motor speed. These motorsloseefficiencyrapidlywhenoil over heats.
-
S3
NOTE: The backboard will slide up or down in relation to the sideboards without loosen-ing any other bolts. As shown in figure 1, arrow 1, on page 6.
Suggestion: When adjusting the sickle and the backboard sliding with it, loosen the bolts and nuts shown in the Fig. 1, arrow 4 on page 6 . There are nuts, bolts, and straps on both the front and rear sides of the machine.
3. Retighten the four 5/8” bolts loosened in step one on previous page.
FLOW CONTROL VALVE ADJUSTMENT
The flow control valve on the right controls the speed of the sickle. Loosen the knob on the valve to adjust the lever and move the le-ver to a higher number to increase the speed. To lower the number is to decrease speed. After moving the lever, tighten the knob to hold the lever in place.
For initial setting of the valves, set each adjusting lever on “2”. Fine tune the speed of the sickle and slats by adjusting the valves individually to get the proper cutting for the type of hay you are processing.
FEEDING RATE
The feeding rate may be adjusted by chang-ing the speed of the feeder chain, or by adjusting the distance between the sickle and the table slats. To change this distance, use the following procedure.
SAFETY WARNING!Turn off tractor and disconnect the hydrau-lic hoses before making any adjustments to the sickle! Failure to do so could result in serious personal injury!
1. Loosen the two 5/8” hex bolts (1) and two 5/8” carriage bolts (2) that hold the sickle bar in place. (See Fig. 3)
2. Screw the 3/4” all thread adjustment bolts (3) in or out at each end of the sickle. Make sure that each end is adjusted so that the sickle is parallel with the table slats. Use a tape measure to gauge each end.
Adjustments
9
2
3
1
-
S3
TRAILER MAINTENANCEMONTHLY (Or every 100 bales) Grease the linkage of the lift arm to avoid binding and rust.
ANNUALLY Clean and repack the wheel bearings.
TABLE MAINTENANCEMONTHLY (Or every 100 bales) Grease Shumacher gear box with MAX 5 shots of lithium based grease every 50 operating hours.
Knife-head bearing should be greased every 12 operating hours with 1 shot of grease.
Check the conveyor chain for tightness. The chain should not swag more than 6” from the bottom of the table at the center. Adjust the take-up roller equally at each end for maximum chain life.
Take-up Roller
Maintenance
10
-
S311
Lubricate the system drive chains with chain oil. - Non-detergent petroleum based or synthetic, multigrade 20/50 oil.
Inspect Schumacher drive belt for stretching from normal wear, tighten belt as necessary. Inspect for unusual/excessive belt wear such as fraying, glazing, or other abnormalities, replace as necessary. part # 440081 - 25-30 lbs. of tension with 3/4” deflection between tensioner pulley and Schumacher pulley.
Inspect sickle sections for wear, and replace as necessary.
Remove lower Schumacher shield and remove excess hay from drive area.
BI-ANNUALLY Check belt tension - 25-30 lbs. with 3/4” deflection between tensioner pulley and Schumacher pulley.
DRIVE SHAFT MAINTENANCEMONTHLY (Or every 100 bales) Grease all grease zerks on the drive shaft. (Zerks located at each end and one in the middle of the shaft.)
Inspect and replace any broken or missing safety shields. Check for loose bolts on drive shaft.
-
S3
-
S3
PARTS SECTION
-
S3
-
S3
Table of ContentsPARTS SECTION Table and Feed Chain...................................... Trailer Assembly............................................... Backboard and Sides....................................... Safety Shields................................................... Table Safety Stops........................................... Sickle Height Adjustment.................................. Twine Box - Optional......................................... Decals...............................................................
Sickle Drive Assembly...................................... PTO Kit............................................................. Sickle Assy........................................................ PTO Holder....................................................... Hydraulic Hoses............................................... Hydraulic Option............................................... Hydraulic Option Schematic.............................
1.11.21.31.41.51.61.71.8
2.12.22.32.42.52.62.7
-
S31.1
4050
16Pa
rts L
ist
ITEM
QTY
PAR
T #
DES
CR
IPTI
ON
15
1104
00BO
LT, 3
/8-1
6 X
2.0
24
1104
02Bo
lt, 3
/8-1
6 X
1.25
in C
arria
ge3
411
0419
BO
LT, 1
/2-1
3 X
1.7
54
411
0420
BO
LT, 3
/8-1
6 X
1.0
54
1104
25B
OLT
, 3/8
-16
X 1
.25
62
1104
29B
OLT
, 1/2
-13
X 1
.57
311
0437
BOLT
, 3/8
-16
X 0
.75,
WIZ
FLA
NG
E8
126
1105
61B
OLT
, 1/4
-20
X .7
59
611
0610
NU
T, 1
/2-1
310
211
0615
NU
T, 1
/2-1
3, U
NIT
OR
QU
E LO
CK
1112
611
0630
NU
T, 1
/4-2
0 LO
CK
(NYL
ON
INSE
RT)
121
1106
45N
UT,
3/8
-16
WIZ
FLA
NG
E13
211
0658
WAS
HER
, 1/2
" FLA
T ST
AN
DAR
D14
1611
0672
WA
SHER
, 3/8
" LO
CK
1521
1106
76W
ASH
ER, 3
/8" F
LAT
STA
ND
ARD
1612
1108
26N
UT,
3/8
-16
GR
517
134
0007
Spr
ocke
t, 60
30 X
1.2
518
140
0014
DEC
AL, S
HIE
LD R
EMO
VED
191
4050
15as
sem
bly,
driv
e ch
ain
cove
r20
541
0232
Bear
ing
Inse
rt, 2
.83,
1.2
5" e
c Lk
Parts
Lis
tIT
EMQ
TYPA
RT
#D
ESC
RIP
TIO
N21
841
0233
Flan
ge, 2
Hol
e22
441
0238
Key
, 1/4
X 1
/4 X
2.2
523
241
0243
BEAR
ING
, 2fn
g Sd
1.3
7524
241
0281
ADJU
STM
ENT
BR
AC
KET
ASS
Y25
141
0365
MO
TOR
AD
J. P
LATE
261
4103
70Sh
ield
, Sla
t Mot
or27
141
0375
SPR
OC
KET,
60b
10 X
1.0
281
4104
42C
onne
ctin
g Li
nk, #
60 C
hain
293
4111
17C
hain
, Fee
der
3010
4111
35SL
AT31
141
1137
SHAF
T, S
LAT
DR
IVE
323
4111
70H
alf L
ink,
Offs
et, 2
060h
331
4111
71W
ELD
MEN
T, S
LAT
RO
LLE
R34
241
1294
CEN
TER
BE
AR
ING
MO
UN
T35
1141
5003
Toot
hed
Slat
361
4150
04W
eldm
ent,
Tabl
e37
142
0128
Mot
or, E
aton
101
-101
4 (1
4.1
CI)
381
4400
34C
hain
, Sla
t Driv
e39
344
0070
Spr
ocke
t,206
2b13
x1.2
5k2s
s,tim
e40
144
0078
DR
IVE
sha
ft
Tabl
e an
d fe
ed c
hain
11/1
3/19
-
S3ii 1.1
DE
TAIL
HSC
ALE
0.1
2 : 1
4050
16
H
37
31
30
26
7
277
2
4
20
29
39
38
1715
4023
23
18
28
10
6
41
24
162215
17
1
25
34
8
1136
1235
16
1
21
32
40
17
1516
522
Add
blu
e lo
ctite
to s
et s
crew
s an
das
not
ed (1
)
14
14
21
1
-
S3iii 1.1
DET
AIL
ASC
ALE
0.1
: 1
DE
TAIL
BS
CA
LE .1
:1D
ETA
IL C
SCA
LE 0
.1 :
1
DET
AIL
DS
CA
LE 0
.1 :
1
4050
16
A
B
C
D
18
323
9
-
S3iv 1.1
DE
TAIL
AS
CAL
E 1
/ 10
DE
TAIL
BS
CA
LE 1
/ 10
4050
16
AB
3
9
913
-
S31.2
DET
AIL
ASC
ALE
0.06
: 1
A
27
25
15
2616
12
26
9
4
7
13
17
8
10
11
2223
24
19
14
18
Trai
ler a
ssem
bly
and
parts
11/1
8/20
19
20.2
.1.1
21.2
8.4
21.2
8.2
21.2
8.1
21.2
8.7
21.2
8.8
21.2
8.3
20.2
.1.3
20.2
.1.4
21.2
8.5
20.2
.1.2
15
28
-
S3ii 1.2
Parts
Lis
tIT
EMQ
TYPA
RT
#D
ESC
RIP
TIO
N1
510
2009
Cov
er P
late
25
1020
10C
lam
p Bo
dy3
411
0323
Bol
t, 1/
4-20
X1
3/8
49
1104
19BO
LT, 1
/2-1
3 X
1.75
51
1104
91BO
LT, 5
/16-
18 X
2.7
56
911
0610
NU
T, 1
/2-1
37
911
0658
WA
SHER
, 1/2
" FLA
T ST
AND
ARD
82
1106
64W
ASH
ER, 1
" FLA
T SA
E9
911
0666
WA
SHER
, 1/2
" LO
CK
102
1106
73W
ASH
ER, 1
/4" F
LAT
STA
ND
ARD
111
1520
04H
OLD
ER
, MAN
UAL
122
2000
06D
ECAL
, DEW
EZE
RE
D O
N M
ETA
LIC
131
4100
22PI
N, S
WIN
G A
RM
141
4100
26O
UTE
R F
OR
K A
SSY
152
4100
37W
ELD
MEN
T, P
IN16
141
0069
PIN
, OU
TTE
R F
OR
K17
141
0176
PIN
, CYL
BA
SE
181
4103
99BA
LE K
ICKE
R A
SSY
191
4107
15B
ASIC
FO
RK
ASSY
, SLI
CER
ON
LY20
141
1159
Wel
dmen
t, Tr
aile
r, S3
Parts
Lis
tIT
EMQ
TYPA
RT
#D
ESC
RIP
TIO
N20
.2.1
.12
4100
40S
PIN
DLE
- 35
-6LM
-S20
.2.1
.22
5101
75C
OTT
ER P
IN, 3
/16
X 2
20.2
.1.3
211
0654
Was
her,
1.75
X .8
15 S
pind
le20
.2.1
.42
1106
13N
UT,
CA
STLE
3/4
-16
212
4130
01H
UB
CO
MP
LETE
, 35-
6LM
21.2
8.1
141
0111
Hub
6X6
in21
.28.
21
4101
04/4
101
14IN
NER
RAC
E AN
D B
EAR
ING
21.2
8.3
141
0103
/410
115
OU
TER
RA
CE
AND
BEA
RIN
G
21.2
8.4
141
0105
SEA
L21
.28.
51
4101
12D
UST
CAP
21.2
8.7
611
3006
Stud
9/1
6-18
21.2
8.8
611
3007
Nut
9/1
6-18
222
4200
05C
OU
PLER
, PIO
NEE
R M
ALE
231
4200
06H
OSE
, .37
X 2
06.4
8 6
MB/
6-8M
P24
142
0011
Hos
e .3
7 X
224.
48 6
mb/
6-8m
p25
142
0014
CYL
IND
ER 4
.0 X
18
265
5101
75C
OTT
ER P
IN, 3
/16
X 2
272
7105
86SC
REW
, 1/4
X 1
TEK
SE
LF-T
AP28
182
0097
CLA
MP
BO
DY
Trai
ler p
arts
list
11/1
8/20
19
-
S31.3
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMBO
LT, 3
/8-1
6 X
1.25
1104
2512
1W
ASH
ER, 3
/8" L
OC
K11
0672
122
WAS
HER
, 3/8
" FLA
T ST
AND
ARD
1106
7612
3N
UT,
3/8
-16
GR
511
0826
124
Side
, fro
nt, a
ssem
bly
4050
081
5S
IDE,
RIG
HT/
BAC
K41
0076
16
BAC
KBO
ARD
ASS
EMBL
Y41
0196
17
Back
boar
d an
d si
des
1
34
2
6
7
11/2
1/20
19
5
-
S31.4
DET
AIL
ASC
ALE
0.06
: 1
DET
AIL
BSC
ALE
0.08
: 1
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMC
LIP,
HAI
RPI
N21
0326
21
Shie
ld, b
elt,
com
plet
e40
5005
12
Shie
ld, b
elt,
door
com
plet
e40
5006
13
Shie
ld, b
elt,
mov
ing,
com
plet
e40
5007
14
A
B
SAFE
TY S
HIE
LDS
11/1
3/20
19
2 3
4Oth
er s
hiel
ds s
how
n w
ith th
eir r
espe
ctiv
e di
agra
ms
2
4
3
1
2103
26 c
lip in
stal
led
here
-
S3
DET
AIL
ASC
ALE
1 / 5
DET
AIL
BSC
ALE
1 / 5
A
B
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMBO
LT, 1
/2-1
3 X
1.25
1104
422
1N
UT,
1/2
-13
1106
104
2Ta
ble,
com
plet
e41
5007
13
Trai
ler C
ompl
ete
4150
101
4
11/1
9/20
19Ta
ble
safe
ty s
tops
2
1
2
1
2
2
4
3
1.5
-
S31.6
DET
AIL
ASC
ALE
1 / 1
0 DET
AIL
BSC
ALE
1 / 1
0
DET
AIL
CSC
ALE
1 / 1
0
A
B
C
Sick
le H
eigh
t Adj
ustm
ent
11/1
3/20
19
Loos
en n
uts
on o
ppos
ite s
ide
Use
jack
scr
ewfo
r adj
ustm
ent
Loos
en fo
r adj
ustm
ent
jack
scr
ew
jack
scr
ew
-
S31.7
Part
s Li
st
DES
CRIP
TIO
NPA
RT #
QTY
ITEM
BOLT
, 3/8
-16
X 1.
011
0420
41
NU
T, 3
/8-1
6, U
NIT
ORQ
UE
LOCK
1106
214
2
WA
SHER
, 3/8
" FLA
T ST
AN
DA
RD11
0676
83
PUSH
NU
T, W
ASH
ER C
AP
STYL
E11
2011
34
CLEV
IS P
IN, S
TD Z
P 1/
4 X
1 5/
811
2095
35
wel
dmen
t, ne
t wra
p bo
x, b
otto
m41
5008
16
SCRE
W, 1
0-24
X1.2
5 PA
N H
EAD
PH
PS11
0339
16.
1
NU
T, 1
0-24
LO
CK N
YLO
N IN
SERT
1106
311
6.2
Keep
er, D
raw
Lat
ch11
2106
16.
3
bott
om, n
et w
rap
box,
S3
4115
451
6.4
fron
t, ne
t wra
p bo
x, S
341
1546
16.
5
wel
dmen
t, ne
t wra
p bo
x lid
4150
091
7
SCRE
W, 1
0-24
X1.2
5 PA
N H
EAD
PH
PS11
0339
27.
1
NU
T, 1
0-24
LO
CK N
YLO
N IN
SERT
1106
312
7.2
LATC
H, R
UBB
ER T
-HA
ND
LE D
RAW
1121
051
7.3
lid, n
et w
rap
box,
S3
4115
471
7.4
7.3
6.1
6.2
6.3
6.5
57.
4
2
31
7.1 4
6.4
7.4
7.2
OPT
ION
AL
TWIN
E BO
X
-
S3
-
S31.8
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMD
ecal
, Dew
eze
Red
on
Blac
k20
0005
31
Dec
al, D
ange
r Mov
ing
Sic
kle
4000
124
2D
ECAL
, SH
IELD
REM
OV
ED40
0014
23
S3 d
ecal
4000
933
4Su
per S
licer
(sm
all)
deca
l40
0094
35
S3 s
traig
ht s
tripe
4000
952
6S3
sca
llope
d st
ripe
deca
l40
0096
27
DEC
ALS
AND
SAF
ETY
DEC
ALS
7
45
6
2
3
45 11
/13/
2019
11
Oth
er s
afet
y de
cals
sho
wn
with
thei
r res
pect
ive
diag
ram
s
-
S3ii 1.8
2.62
5
20.9
61
2.62
5
22.8
96
.342
.342
6.20
0
6.20
0
24.0
0024
.000
26.9
23
28.8
75
DEC
AL P
LAC
EMEN
T11
/13/
19
-
S32.1
Part
s Li
st
DES
CRI
PTIO
NPA
RT #
QTY
ITEM
BOLT
, 1/2
-13
X 2.
511
0403
31
BOLT
, 1/2
-13
X 1.
7511
0419
42
BOLT
, 5/8
-11
X 3.
7511
0510
13
NU
T, 1
/2-1
3 W
IZ F
LAN
GE
1105
888
4
NU
T, 1
/2-1
311
0610
35
WA
SHER
, 1/2
" FLA
T ST
AN
DA
RD11
0658
106
WA
SHER
, 5/8
" FLA
T SA
E11
0663
27
WA
SHER
, 1/2
INT.
TO
OTH
LO
CK11
1172
48
Schu
mac
her P
ro D
rive
4400
721
9
pulle
y 18
0mm
dia
met
er44
0073
110
QD
SF
1 3/
8" d
rive
bush
ing
4400
791
11
1 C
85 S
F44
0080
112
pulle
y, 6
inch
, Don
Dye
4420
061
13
Belt,
C11
544
0081
114
Sick
le D
rive
Ass
embl
y11
/13/
2019
5 6
1
2
73
910
13
14
1112
This
dia
gram
cov
ers
the
basi
c dr
ive
asse
mbl
yfo
r bot
h hy
drau
lic a
nd P
TO S
licer
s
4
8
-
S32.2
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMSe
tScr
ew, 3
/8-1
6 X
0.7
511
0325
21
BOLT
, M6x
1 x
45, G
r 8.8
1111
834
2N
ut, M
6 x
1, T
op L
ock
1111
844
3KE
Y 5/
16" X
5/1
6" X
1 1
/4"
4103
891
4PT
O s
haft,
CV
4430
021
5
4
2
3
5
PTO
kit
12/2
0/19
Wei
ght:
11.5
7 lb
mas
s
1
Parts
2 a
nd 3
can
be
foun
d on
the
right
sid
e of
the
Schu
mac
her g
ear b
ox m
ount
ass
embl
y
-
S32.3
DET
AIL
ASC
ALE
0.16
: 1
DET
AIL
BSC
ALE
0.08
: 1
4050
12
A
B
12.1
.512
.3
12.2
12.1
.2
7.2
7.1
11
65
102
4
3
Sick
le A
ssem
bly
11/2
0/19
1
6
1389
2
4
3
12.1
.1
12.1
.3
12.1
.4
-
S3ii 2.3
Par
ts L
ist
ITE
MQ
TYP
AR
T #
DE
SCR
IPTI
ON
120
1100
54B
olt,
7/16
-14
X 2
.5 in
Car
riage
26
1105
35B
OLT
, 7/1
6-14
X 1
.53
2611
0641
NU
T, 7
/16-
144
2611
0671
WA
SH
ER
, 7/1
6" L
OC
K5
140
0014
DEC
AL,
SH
IELD
RE
MO
VE
D6
2340
0031
Stu
b G
uard
, Sup
er S
licer
II7
140
5013
asse
mbl
y, s
ickl
e en
d co
ver
7.1
141
1542
shie
ld, s
ickl
e en
d pl
ate
7.2
150
0038
Dec
al, D
ange
r Kee
p C
over
s In
Pla
ce8
941
0710
PLA
TE, S
TUB
GU
AR
D A
DJ.
910
4107
11S
HIM
, STU
B G
UA
RD
101
4115
39P
late
, not
ched
stu
b gu
ard,
adj
Par
ts L
ist
ITE
MQ
TYP
AR
T #
DE
SC
RIP
TIO
N11
141
5005
Wel
dmen
t, S
ickl
e m
ount
, S3
121
4400
77co
mpl
ete,
sic
kle
assy
12.1
144
0076
sick
le, a
ssy,
S3
12.1
.11
4101
92S
ickl
e B
ar12
.1.2
2741
0193
Sic
kle
Sec
tion,
3"
12.1
.354
1106
30N
UT,
1/4
-20
LOC
K (N
YLO
N IN
SE
RT)
12.1
.443
1105
61B
OLT
, 1/4
-20
X .7
512
.1.5
1111
0430
BO
LT, 1
/4-2
0 X
1-1
/412
.21
4420
04S
chum
ache
r sic
kle
conn
ecto
r12
.31
4420
05S
chum
ache
r nyl
on b
ushi
ng13
2051
0161
SetS
crew
, 3/8
-16
X 0
.5
Sic
kle
parts
list
11/2
0/19
-
S32.4
PTO
HO
LDER
Part
s Li
st
DES
CRIP
TIO
NPA
RT #
QTY
ITEM
Pin,
Lin
ch, .
25 X
3.0
1021
291
1
BOLT
, U, S
QU
ARE
3/8
X 4
X 4
3/4
1103
631
2
BOLT
, 5/1
6-18
X 3
.25
1105
362
3
NU
T, 5
/16-
18, U
NIT
ORQ
UE
LOCK
1106
002
4
PTO
sha
ft h
olde
r41
1557
15
Base
, PTO
hol
der,
right
4115
581
6
Base
, PTO
hol
der,
left
4115
591
7
This
sid
e to
war
d to
ngue
of m
achi
ne
5 Wei
ght:
3.41
lbm
ass
3
2
1
6
4
7
3/8
nut p
rovi
ded
with
110
363
U b
olt
-
S32.5
DET
AIL
ASC
ALE
0.10
: 1
DET
AIL
BSC
ALE
0.08
: 1
A
B
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMH
ose
.5 X
99.
2 8-
10fjx
/8-8
mp
4201
372
1H
ose
.500
X 7
1.78
8-1
0fjx
/8-1
0fjx
4201
431
2H
ose
.5 X
87.
28 8
-10f
jx/8
-10f
jx42
0144
13
valv
e, fl
ow c
ontro
l,-10
SAE
(FC
R51
-10-
2600
)42
0147
14
Hyd
raul
ic h
oses
Seco
ndar
y hy
drau
lic fl
ow c
ontro
lva
lve
inst
alle
d he
re o
n hy
drau
lic s
licer
11
32
11/2
0/19
23
End
of #
2 ho
se in
stal
led
here
on P
TO s
licer
End
of #
3 ho
sein
stal
led
here
on P
TO s
licer
Hyd
raul
ic k
it di
agra
m p
rovi
ded
on h
ydra
ulic
opt
ion
page
Hyd
raul
ic k
it: #
4250
01
-
S32.6
DET
AIL
ASC
ALE
1 / 5
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMBO
LT, 5
/16-
18 X
1-1
/211
0377
21
BOLT
, 1/4
-20
X 2.
511
0410
22
BOLT
, 3/8
-16
X 1.
011
0420
63
NU
T, 5
/16-
1811
0608
24
NU
T, 1
/4-2
011
0609
25
WA
SHER
, 1/4
" LO
CK
1106
672
6W
ASH
ER, 3
/8" L
OC
K11
0672
67
WA
SHER
, 5/1
6" L
OC
K11
0674
28
NU
T, 3
/8-1
6 G
R 5
1108
262
9AD
APT
ER
, 10M
J-10
FJX9
012
0217
210
ADA
PTE
R, 1
0MJ-
10M
B90
1202
243
11AD
APT
ER
, 10M
J-10
MB
1202
512
12A
DAP
TER
, 10M
J-10
MJ-
10M
B12
0258
113
ADA
PTE
R, 1
0MJ-
10FJ
X45
1207
301
14C
oupl
er, S
proc
ket,
flex,
1" K
ss41
0229
115
Cha
in, M
otor
Driv
e C
oupl
er41
0230
116
Cou
pler
, Spr
ocke
t, fle
x, 1
3/8
K41
0262
117
KEY
5/16
" X 5
/16"
X 1
1/4
"41
0389
118
Con
nect
ing
Link
, #60
Cha
in41
0442
119
Mou
nt p
late
, Hyd
raul
ic b
elt d
rive
mot
or, S
341
1540
120
brac
ket,
hydr
aulic
val
ve41
1549
121
Mot
or, S
chum
ache
r Driv
e 10
1-10
11-0
0942
0139
122
Hos
e .5
X 2
7.28
8-1
0fjx
/8-1
0fjx
4201
401
23H
ose
.5 X
21.
28 8
-10f
jx/8
-10f
jx42
0141
124
Hos
e .5
X 1
0.78
8-1
0fjx
/8-1
0fjx
4201
421
25va
lve,
flow
con
trol,-
10 S
AE(F
CR
51-1
0-26
00)
4201
471
26
A
14
21
2
3
22
13
10
25
2423
20
22
20
16
1
17 21 25
84
56
19
Hyd
raul
ic o
ptio
n11
/19/
2019
11
12
11
127
9
15
26
18
2.7
-
S3
Sick
lem
otor
Tabl
em
otor
IN
CF
EX
IN
CF
EX
From
trac
tor
to s
licer
From
slic
erto
trac
tor
Hyd
raul
ic o
ptio
n sc
hem
atic
11/1
9/20
19
4201
41
4201
40
4201
42
4201
43
4201
44
4200
48
4201
3942
0128
1202
58
1202
58
4201
37
4201
37
2.7
-
S3
NOTES
Harper Industries, Inc.151 E. Highway 160Harper, KS 67058
Website: www.harperindustries.com
Telephone: 620-896-7381Toll-Free: 800-835-1042Fax: 620-896-7129
E-mail: [email protected]