COMMERCIAL VERTICAL CLADDING

MC760

0800 ROOFNZ (0800 766 369)www.metalcraftroofing.co.nz

Architectural / Specification EnquiriesPh: 09 274 0408

Mobile: 027 603 1096Email: Frances.charles@unitedindustries.co.nzCVMC760

00 / 20 COVER SHEET01 / 20 PARAPET AND BALUSTRADE CAPPING02 / 20 SOFFIT03 / 20 FLUSH WINDOW HEAD04 / 20 FLUSH WINDOW SILL05 / 20 FLUSH WINDOW JAMB05A / 20 FLUSH WINDOW JAMB ALTERNATIVE OPTION06 / 20 RECESSED WINDOW HEAD07 / 20 RECESSED WINDOW SILL08 / 20 RECESSED WINDOW JAMB08A / 20 RECESSED WINDOW JAMB ALTERNATIVE OPTION09 / 20 BUTT WINDOW HEAD10 / 20 BUTT WINDOW SILL11 / 20 BUTT WINDOW JAMB11A / 20 BUTT WINDOW JAMB ALTERNATIVE OPTION12 / 20 METERBOX HEAD13 / 20 METERBOX SILL14 / 20 METERBOX JAMB15 / 20 INTERNAL CORNER16 / 20 EXTERNAL CORNER17 / 20 SOAKER FLASHING18 / 20 BOTTOM OF CLADDING (FLUSH)19 / 20 BOTTOM OF CLADDING (RECESSED)20 / 20 3D WINDOW FLASHINGS

DETAIL LIST

PRE-FINISHED PARAPET CAP FLASHINGNO FIXINGS ON TOP OF FLASHING

BUILDING PAPER SHOWN DASHED

PRE-FINISHED SELF DRILLING / TAPPINGSCREW WITH RUBBER WASHER

METALCRAFT MC760 VERTICALCLADDING

METALCRAFT MSS PURLINBY ENGINEER

CONTINUOUS TIMBER PACKING

MIN

. 5.00°

BUILDING PAPER TO PROVIDESEPARATION OF METAL CAPPINGAND TIMBER SHOWN DASHED

Z

CLE

ARAN

CE

25m

m

5 GAP

20

15

ALTERNATIVE OPTIONBIRDS BEAK EDGE

PRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8gWAFER-TEK SCREW

HEMMED EDGE

STOPENDS TO WALL CLADDING

COMPRESSIBLE FOAM SEAL. REFERTO MRM CODE OF PRACTICE VERSION2.2 /2012 FOR REQUIRMENT.

CLE

ARAN

CE

25m

m

Z

20mm CAVITY

CATEGORY A

1. NORMAL EXPOSURE2. ROOF PITCH >10°

MIN. 50mm (VERTICALLY DOWN FACE - SMOOTH)

MIN. 75mm (VERTICALLY DOWN FACE - PROFILED)

CATEGORY B

1. EXPOSED (HIGHER RISK)2. WIND LOAD EXCEEDS 1.5kPa.3. ROOF PITCH <10°

MIN. 75mm (VERTICALLY DOWN FACE - SMOOTH)

MIN. 100mm (VERTICALLY DOWN FACE - PROFILED)

Z

SITUATION 1

1. LOW, MEDIUM, HIGH WIND ZONES2. ROOF PITCH ≥ 10°

MIN. 50mm

SITUATION 2

1. VERY HIGH WIND ZONE2. ALL ROOF PITCHES

MIN. 70mmZ

SITUATION 3

1. EXTRA HIGH WIND ZONE2. ALL ROOF PITCHES

MIN. 90mm

PLEASE REFER TO E2 FOR FURTHER INFORMATION ON FLASHING COVER WIDTHS.

PLEASE REFER TO MRM CODE OF PRACTICE VERSION 2.2/2012 FOR FURTHER INFORMATION ON FLASHING COVER WIDTHS.

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 01 / 20

PARAPET AND BALUSTRADE CAPPING

2015

METALCRAFT MSS PURLINBY ENGINEER

INTERNAL WALL LINING

METALCRAFT MSS PURLIN BY ENGINEER

20mm CAVITY

SEPARATE BATTEN ANDFLASHING WITH EPDM ASREQUIRED

BARGE BOARD

SOFFIT LINING

METALCRAFTMSS PURLIN BYENGINEER

PRE-FINISHED SELFDRILLING/TAPPING SCREWWITH RUBBER WASHER

INTERNAL CEILING LINING

COMPRESSIBLE FOAM SEAL. REFER TO MRM CODEOF PRACTICE VERSION 2.2 /2012 FOR REQUIRMENT.

PRE-FINISHEDSOFFIT FLASHING

PRE-FINISHED FLAT HEAD WAFER-TEK SCREWFOR FLASHING

BUILDING PAPER SHOWNDASHED

METALCRAFT MC760 VERTICALCLADDING

PRE-FINISHED POP RIVETBEDDED IN SILICONE OR PRE-FINISHED 8g WAFER-TEKSCREW

STOPENDS TO WALL CLADDING

MIN. 50mm

CO

VER

CLA

DD

ING

60m

m (M

IN. 3

5mm

)

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 02 / 20

SOFFIT

2015

BUILDING PAPER DRESSED INTOOPENING WITH FLEXIBLE FLASHINGTAPE INSTALLED OVER WRAP TOCORNERS AT HEAD

TEMPORARY PACKER IF REQUIRED,REMOVED AFTER FIXING

EXTRA BUILDING PAPER OVER WINDOWHEAD FLASHING SHOWN DASHED

INTERNAL WALL LINING METALCRAFT MC760 VERTICALCLADDING

PRE-FINISHED WINDOW HEADFLASHING WITH 15° FALL

DOUBLE GLAZING WINDOW JOINERY

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD, SILLAND JAMB

WINDOW HEAD LINER

LINE OF WINDOW JAMBLINER BEHIND

STOPENDS TO HEAD FLASHING

LINE OF JAMB FLASHING BEHIND

METALCRAFT MSS PURLIN BYENGINEER

PRE-FINISHED SELF DRILLING / TAPPINGSCREW WITH RUBBER WASHER

PRE-FINISHED FLAT HEAD WAFER-TEK SCREW FOR FLASHING

CAVITY CLOSER AS REQUIRED TO NZBC

COMPRESSIBLE FOAM SEAL TOFILL OVERLAP OF FLASHING

5mm

GAP

DR

IP E

DG

E TO

CLA

DD

ING

MIN

. 15m

m G

AP

MIN

. 75m

m W

ITH

OU

T H

EM

ED

GE

MIN

. 50m

m C

OVE

R

MIN

. 10m

m C

OVE

R

SU

GG

EST

MIN

. 50m

m

DIM

ENS

ION

TO

SU

IT

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 03 / 20

FLUSH WINDOW HEAD

2015

METALCRAFT MC760 VERTICALCLADDING

BUILDING PAPER SHOWN DASHED

WINDOW SILL SUPPORT BAR

LINE OF WINDOW JAMBLINER BEHIND

WINDOW SILL LINER

MIN. 8mm PACKER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

COMPRESSIBLE FOAM SEAL. REFERTO MRM CODE OF PRACTICE VERSION2.2 /2012 FOR REQUIRMENT.

METALCRAFT MSS PURLIN BYENGINEER

INTERNAL WALL LINING

STOPENDS TO SILL FLASHING

LINE OF JAMB FLASHING BEHIND

20mm CAVITY

FLEXIBLE FLASHING TAPE OVER BUILDINGPAPER FOR FULL WIDTH/DEPTH SILL

PRE-FINISHED WINDOW SILL FLASHING

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

PRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8g WAFER-TEK SCREW

PRE-FINISHED SECONDARY FLASHING

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

DOUBLE GLAZING WINDOW JOINERY

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

MIN

. 8m

m C

OV

ER

CO

VER

CLA

DD

ING

65m

m (M

IN. 3

5mm

)

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 04 / 20

FLUSH WINDOW SILL

2015

METALCRAFT MC760 VERTICALCLADDING

BUILDING PAPER SHOWN DASHED

DOUBLE GLAZING WINDOWJOINERY

LINE OF WINDOW SILL LINERBELOW

WINDOW JAMB LINER

TIMBER PACKER

AIRSEAL ON BACKING ROD TORUN CONTINUOUSLY AROUNDHEAD, SILL AND JAMB

20mm JAMB BATTEN

INTERNAL WALL LINING

LINE OF SILL FLASHING BELOW

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

METALCRAFT MSS PURLIN BY ENGINEER

LINE OF SILL FLASHING BELOW

PRE-FINISHED WINDOW JAMBFLASHING

MIN. 10mm COVER

FLEXIBLE FLASHING TAPEOVER BUILDING PAPER FORFULL WIDTH/DEPTH SILL

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

5mm

GAP

MIN. 2 CRESTS

PRE-FINISHED SECONDARYFLASHING

LINE OF HEAD FLASHING ABOVE

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

COMPRESSIBLE FOAMSEAL TO FILL OVERLAPOF FLASHING

PRE-FINISHED POPRIVET BEDDED INSILICONE OR PRE-FINISHED 8gWAFER-TEK SCREW

5mm

GAP

LINE OF HEAD FLASHING ABOVE

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 05 / 20

FLUSH WINDOW JAMB

2015

METALCRAFT MC760 VERTICALCLADDING

BUILDING PAPER SHOWN DASHED

DOUBLE GLAZING WINDOW JOINERY

LINE OF WINDOW SILL LINER BELOW

WINDOW JAMB LINER

TIMBER PACKER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

20mm JAMB BATTEN

INTERNAL WALL LINING

LINE OF SILL FLASHING BELOW

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

METALCRAFT MSS PURLIN BY ENGINEER

PRE-FINISHED FIXING BRACKET WITHPRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8g WAFER-TEK SCREW

LINE OF SILL FLASHING BELOW

PRE-FINISHED WINDOW JAMBFLASHING

MIN. 10mm COVER

FLEXIBLE FLASHING TAPE OVERBUILDING PAPER FOR FULLWIDTH/DEPTH SILL

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

5mm

GAP

PRE-FINISHED SECONDARYFLASHING

LINE OF HEAD FLASHING ABOVE

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

COMPRESSIBLE FOAM SEAL TO FILLOVERLAP OF FLASHING

SUGGEST MIN. 50mm

DIMENSION TO SUIT

LINE OF HEAD FLASHING ABOVE

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 05A / 20

FLUSH WINDOW JAMB ALTERNATIVE OPTION

2015

BUILDING PAPER DRESSED INTOOPENING WITH FLEXIBLE FLASHINGTAPE INSTALLED OVER WRAP TOCORNERS AT HEAD

TEMPORARY PACKER IF REQUIRED,REMOVED AFTER FIXING

EXTRA BUILDING PAPER OVER WINDOWHEAD FLASHING SHOWN DASHED

INTERNAL WALL LINING METALCRAFT MC760 VERTICALCLADDING

PRE-FINISHED WINDOW HEADFLASHING WITH 15° FALL

DOUBLE GLAZING WINDOW JOINERY

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

WINDOW HEAD LINER

LINE OF WINDOW JAMBLINER BEHIND

STOPENDS TO HEAD FLASHING

LINE OF JAMB FLASHING BEHIND

METALCRAFT MSS PURLINS BYENGINEER

PRE-FINISHED SELF DRILLING /TAPPING SCREW WITH RUBBERWASHER

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

PRE-FINISHED WINDOW HEADFLASHING WITH 15° FALL

CAVITY CLOSER AS REQUIRED TONZBC

5mm

GAP

DR

IP E

DG

E TO

CLA

DD

ING

MIN

. 15m

m G

AP

MIN

. 75m

m W

ITH

OU

T H

EM

ED

GE

MIN

. 50m

m C

OVE

R

MIN

. 10m

m C

OVE

R

SU

GG

EST

MIN

. 50m

m

DIM

ENS

ION

TO

SU

IT

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 06 / 20

RECESSED WINDOW HEAD

2015

METALCRAFT MC760 VERTICALCLADDING

BUILDING PAPER SHOWN DASHED

STOPENDS TO SILL FLASHING

LINE OF WINDOW JAMBLINER BEHIND

WINDOW SILL LINER

MIN. 8mm PACKER

AIRSEAL ON BACKING ROD TORUN CONTINUOUSLY AROUNDHEAD, SILL AND JAMB

INTERNAL WALL LINING

PRE-FINISHED WINDOW SILL FLASHING

LINE OF JAMB FLASHING BEHIND

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

20mm CAVITY

FLEXIBLE FLASHING TAPE OVERBUILDING PAPER FOR FULLWIDTH/DEPTH SILL

DOUBLE GLAZING WINDOW JOINERY

METALCRAFT MSS PURLIN BYENGINEER

COMPRESSIBLE FOAM SEAL. REFERTO MRM CODE OF PRACTICE VERSION2.2 /2012 FOR REQUIRMENT.

PRE-FINISHED SECONDARY FLASHING

PRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8gWAFER-TEK SCREW

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

WINDOW SILL SUPPORT BAR

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

5mm

GAP

MIN

. 8m

m C

OV

ER

CO

VER

CLA

DD

ING

70m

m (M

IN. 3

5mm

)

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 07 / 20

RECESSED WINDOW SILL

2015

METALCRAFT MC760 VERTICALCLADDING

BUILDING PAPER SHOWN DASHED

DOUBLE GLAZING WINDOWJOINERY

LINE OF WINDOW SILL LINERBELOW

WINDOW JAMB LINER

TIMBER PACKER

AIRSEAL ON BACKING ROD TORUN CONTINUOUSLY AROUNDHEAD, SILL AND JAMB

20mm JAMB BATTEN

INTERNAL WALL LINING

LINE OF HEAD FLASHING ABOVE

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

METALCRAFT MSS PURLIN BY ENGINEER

LINE OF SILL FLASHING BELOW

PRE-FINISHEDWINDOW JAMBFLASHING

MIN. 10mm COVER

FLEXIBLE FLASHING TAPEOVER BUILDING PAPER FORFULL WIDTH/DEPTH SILL

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

PRE-FINISHED SECONDARYFLASHING

LINE OF HEAD FLASHING ABOVE

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

PRE-FINISHED POP RIVETBEDDED IN SILICONE ORPRE-FINISHED 8g WAFER-TEK SCREW

MIN. 2 CRESTS 5mm GAP

5mm

GAP

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 08 / 20

RECESSED WINDOW JAMB

2015

PRE-FINISHED FIXING BRACKET WITH PRE-FINISHED POP RIVET BEDDED IN SILICONEOR PRE-FINISHED 8g WAFER-TEK SCREW

DOUBLE GLAZING WINDOW JOINERY

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

METALCRAFT MC760 VERTICALCLADDING

MIN. 10mm COVER

INTERNAL WALL LINING

BUILDING PAPER SHOWN DASHED

LINE OF WINDOW SILL LINER BELOW

WINDOW JAMB LINER

TIMBER PACKER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

20mm JAMB BATTEN

FLEXIBLE FLASHING TAPE OVER BUILDINGPAPER FOR FULL WIDTH/DEPTH SILL

METALCRAFT MSS PURLIN BYENGINEER

PRE-FINISHED SECONDARYFLASHING

LINE OF SILL FLASHING BELOW

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

LINE OF HEAD FLASHING ABOVE

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

PRE-FINISHED WINDOW JAMB FLASHING 5mm GAP

SUGGEST 50mm

DIMENSION TO SUIT

5mm

GAP

LINE OF HEAD FLASHING ABOVE

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 08A / 20

RECESSED WINDOW JAMB ALTERNATIVE OPTION

2015

BUILDING PAPER DRESSED INTOOPENING WITH FLEXIBLE FLASHINGTAPE INSTALLED OVER WRAP TOCORNERS AT HEAD

TEMPORARY PACKER IF REQUIRED,REMOVED AFTER FIXING

EXTRA BUILDING PAPER OVERWINDOW HEAD FLASHING SHOWNDASHED

INTERNAL WALL LINING METALCRAFT MC760 VERTICALCLADDING

PRE-FINISHED WINDOW HEADFLASHING WITH 15° FALL

DOUBLE GLAZING WINDOW JOINERY

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

WINDOW HEAD LINER

LINE OF WINDOW JAMBLINER BEHIND

STOPENDS TO HEAD FLASHING

LINE OF JAMB FLASHING BEHIND

METALCRAFT MSS PURLINS BYENGINEER

PRE-FINISHED SELF DRILLING /TAPPING SCREW WITH RUBBERWASHER

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

PRE-FINISHED WINDOW HEADFLASHING WITH 15° FALL

CAVITY CLOSER AS REQUIRED TONZBC

DR

IP E

DG

E TO

CLA

DD

ING

MIN

. 15m

m G

AP

5mm

GAP M

IN. 7

5mm

WIT

HO

UT

HE

M E

DG

E

MIN

. 50m

m C

OVE

R

MIN

. 10m

m C

OVE

R

SU

GG

EST

MIN

. 50m

m

DIM

ENS

ION

TO

SU

IT

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 09 / 20

BUTT WINDOW HEAD

2015

METALCRAFT MC760 VERTICALCLADDING

BUILDING PAPER SHOWN DASHED

PRE-FINISHED WINDOW SILL FLASHING

LINE OF WINDOW JAMBLINER BEHIND

WINDOW SILL LINER

MIN. 8mm PACKER

AIRSEAL ON BACKING ROD TORUN CONTINUOUSLY AROUNDHEAD, SILL AND JAMB

INTERNAL WALL LINING

STOPENDS TO SILL FLASHING

LINE OF JAMB FLASHING BEHIND

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

20mm CAVITY

FLEXIBLE FLASHING TAPE OVERBUILDING PAPER FOR FULLWIDTH/DEPTH SILL

DOUBLE GLAZING WINDOW JOINERY

METALCRAFT MSS PURLIN BYENGINEER

COMPRESSIBLE FOAM SEAL. REFERTO MRM CODE OF PRACTICE VERSION2.2 /2012 FOR REQUIRMENT.

PRE-FINISHED SECONDARY FLASHING

PRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8gWAFER-TEK SCREW

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

WINDOW SILL SUPPORT BAR

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

5mm

GAP

CO

VER

CLA

DD

ING

60m

m (M

IN. 3

5mm

)M

IN. 8

mm

CO

VER

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 10 / 20

BUTT WINDOW SILL

2015

METALCRAFT MC760 VERTICALCLADDING

BUILDING PAPER SHOWN DASHED

DOUBLE GLAZING WINDOWJOINERY

LINE OF WINDOW SILL LINERBELOW

WINDOW JAMB LINER

TIMBER PACKER

AIRSEAL ON BACKING ROD TORUN CONTINUOUSLY AROUNDHEAD, SILL AND JAMB

20mm JAMB BATTEN

INTERNAL WALL LINING

LINE OF HEAD FLASHING ABOVE

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

METALCRAFT MSS PURLIN BY ENGINEER

LINE OF SILL FLASHING BELOW

PRE-FINISHED WINDOWJAMB FLASHING MIN. 10mm COVER

FLEXIBLE FLASHING TAPEOVER BUILDING PAPER FORFULL WIDTH/DEPTH SILL

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

PRE-FINISHED SECONDARYFLASHING

LINE OF HEAD FLASHING ABOVE

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

PRE-FINISHED POP RIVETBEDDED IN SILICONE ORPRE-FINISHED 8g WAFER-TEK SCREW

MIN. 2 CRESTS 5mm GAP

5mm

GAP

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 11 / 20

BUTT WINDOW JAMB

2015

PRE-FINISHED WINDOW JAMB FLASHING

DOUBLE GLAZING WINDOW JOINERY

LINE OF SILL FLASHING BELOWMETALCRAFT MC760 VERTICALCLADDING

MIN. 10mm COVER

5mm GAP

INTERNAL WALL LINING

BUILDING PAPER SHOWN DASHED

LINE OF WINDOW SILL LINER BELOW

WINDOW JAMB LINER

TIMBER PACKER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

20mm JAMB BATTEN

FLEXIBLE FLASHING TAPE OVER BUILDINGPAPER FOR FULL WIDTH/DEPTH SILL

METALCRAFT MSS PURLIN BYENGINEER

SUGGEST MIN. 50mm

DIMENSION TO SUIT

PRE-FINISHED SECONDARYFLASHING

LINE OF SILL FLASHING BELOW

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

LINE OF HEAD FLASHING ABOVE

LINE OF HEAD FLASHING ABOVE

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

PRE-FINISHED FIXING BRACKET WITH PRE-FINISHED POP RIVET BEDDED IN SILICONEOR PRE-FINISHED 8g WAFER-TEK SCREW

5mm

GAP

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 11A / 20

BUTT WINDOW JAMB ALTERNATIVE OPTION

2015

BUILDING PAPER DRESSED INTOOPENING WITH FLEXIBLE FLASHINGTAPE INSTALLED OVER WRAP TOCORNERS AT HEAD

TEMPORARY PACKER IF REQUIRED,REMOVED AFTER FIXING

EXTRA BUILDING PAPER OVER WINDOWHEAD FLASHING SHOWN DASHED

METALCRAFT MC760 VERTICALCLADDING

PRE-FINISHED HEAD FLASHINGWITH 15° FALL

PRE-FINISHED SELF DRILLING / TAPPINGSCREW WITH RUBBER WASHER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD, SILLAND JAMB

METER BOX STOPENDS TO HEAD FLASHING

LINE OF JAMB FLASHING BEHIND

PRE-FINISHED 'U' BRACKET FIXED TOMETERBOX BEFORE INSTALLATION

METAL ANGLE TO BE CONTINUOUSAROUND METER BOX.

INTERNAL WALL LINING

METALCRAFT MSS PURLINS BYENGINEER

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

CAVITY CLOSER AS REQUIRED TO NZBC

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

5mm

GAP

DR

IP E

DG

E TO

CLA

DD

ING

MIN

. 15m

m G

AP

MIN

. 75m

m W

ITH

OU

T H

EM

ED

GE

MIN

. 50m

m C

OVE

R

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 12 / 20

METERBOX HEAD

2015

METALCRAFT MC760 VERTICALCLADDING

BUILDING PAPER SHOWN DASHED

METER BOX

MIN. 8mm PACKER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

METALCRAFT MSS PURLIN BYENGINEER

PRE-FINISHED SECONDARY FLASHING

INTERNAL WALL LINING LINE OF JAMB FLASHING BEHIND

20mm CAVITY

FLEXIBLE FLASHING TAPE OVER BUILDINGPAPER FOR FULL WIDTH/DEPTH SILL

METAL ANGLE TO BE CONTINUOUSAROUND METER BOX. PRE-FINISHED FLASHING FIXED TO

METAL ANGLE

PRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8g WAFER-TEK SCREW

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

STOPENDS TO SILL FLASHING

COMPRESSIBLE FOAM SEAL. REFERTO MRM CODE OF PRACTICE VERSION2.2 /2012 FOR REQUIRMENT.

STOPENDS TO WALL CLADDING

PRE-FINISHED SELF DRILLING / TAPPINGSCREW WITH RUBBER WASHER

CO

VER

CLA

DD

ING

60m

m (M

IN. 3

5mm

)

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 13 / 20

METERBOX SILL

2015

METALCRAFT MC760 VERTICALCLADDING

BUILDING PAPER SHOWN DASHEDMETER BOX

TIMBER PACKER

20mm JAMB BATTEN

LINE OF SILL FLASHING BELOW

FLEXIBLE FLASHING TAPE OVERBUILDING PAPER FOR FULLWIDTH/DEPTH SILL

PRE-FINISHED SELF DRILLING/TAPPINGSCREW WITH RUBBER WASHER

LINE OF HEAD FLASHING ABOVE

PRE-FINISHED JAMB FLASHINGFIXED TO METERBOX BEFOREINSTALLATION

AIRSEAL ON BACKING ROD

METAL ANGLE TO BE CONTINUOUSAROUND METER BOX.

INTERNAL WALL LINING METALCRAFT MSS PURLINBY ENGINEER

AIRSEAL ON BACKING ROD TO RUNCONTINUOUSLY AROUND HEAD,SILL AND JAMB

SEPARATE BATTEN AND FLASHINGWITH EPDM AS REQUIRED

PRE-FINISHED FLAT HEAD WAFER-TEK SCREW FOR FLASHING

SUGGEST MIN. 50mm

DIMENSION TO SUITPRE-FINISHED POP RIVET BEDDED INSILICONE OR PRE-FINISHED 8gWAFER-TEK SCREW

LINE OF HEAD FLASHING ABOVE

LINE OF SILL FLASHING BELOW

20mm CAVITY

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 14 / 20

METERBOX JAMB

2015

METALCRAFT MC760VERTICAL CLADDING

20mm CAVITY

PRE-FINISHED INTERNALCORNER FLASHING

BUILDING PAPER SHOWNDASHED

STRUCTURAL COLUMN BYENGINEER

METALCRAFT MSS PURLINBY ENGINEER

PRE-FINISHED FLAT HEADWAFER-TEK SCREWWITH EPDM WASHER

PRE-FINISHED SECONDARYFLASHING

SEPARATE BATTEN ANDFLASHING WITH EPDM ASREQUIRED

PRE-FINISHED FLAT HEADWAFER-TEK FOR FLASHING

MIN. 2 CRESTS

PRE-FINISHED POP RIVETBEDDED IN SILICONE ORPRE-FINISHED 8g WAFER-TEK SCREW

5mm

GAP

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 15 / 20

INTERNAL CORNER

2015

METALCRAFT MSS PURLIN BY ENGINEER

20mm CAVITY

PRE-FINISHED FLAT HEAD WAFER-TEKSCREW FOR FLASHING

PRE-FINISHED EXTERNALCORNER FLASHING

SEPARATE BATTEN ANDFLASHING WITH EPDM ASREQUIRED

BUILDING PAPER SHOWNDASHED

METALCRAFT MC760VERTICAL CLADDING

STRUCTURAL COLUMN BY ENGINEER

5mm

GAP

PRE-FINISHED FLAT HEADWAFER-TEK SCREW WITHEPDM WASHER

PRE-FINISHEDSECONDARY FLASHING

PRE-FINISHED POP RIVETBEDDED IN SILICONE ORPRE-FINISHED 8g WAFER-TEK SCREW

MIN. 2 CRESTS

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 16 / 20

EXTERNAL CORNER

2015

BUILDING PAPER SHOWNDASHED

METALCRAFT MC760VERTICAL CLADDING

PRE-FINISHED FLAT HEADWAFER-TEK SCREW FORFLASHINGINTERNAL WALL LINING

SEPARATE BATTEN ANDFLASHING WITH EPDM ASREQUIRED

METALCRAFT MSS PURLINBY ENGINEER

PRE-FINISHED SOAKERFLASHING TO LINE UP WITHWINDOW JAMB ABOVE

20 mm CAVITY

METALCRAFT MSS PURLIN BYENGINEER

SOAKER FLASHING ONLY REQUIRED TOLINE UP WITH WINDOW JAMB ABOVE.REFER TO MRM CODE OF PRACTICEVERSION 2.2 /2012 FOR REQUIRMENT.

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 17 / 20

SOAKER FLASHING

2015

BUILDING PAPER SHOWN DASHED

INTERNAL WALL LINING

METALCRAFT MC760 VERTICALCLADDING

PRE-FINISHED FLAT HEAD WAFER-TEK SCREW FOR FLASHING

CAVITY CLOSER AS REQUIRED TONZBC

PRE-PRIMED SKIRTING

CONCRETE SLAB

MIN

. 50m

m L

AP

VEN

TILA

TIO

N G

AP

3 - 5

mm

GAP

DR

IP E

DG

E TO

CLA

DD

ING

MIN

. 15m

m G

AP

METALCRAFT MSS PURLIN BYENGINEER

PRE-FINISHED SELF DRILLING / TAPPINGSCREW WITH RUBBER WASHER

20mm CAVITY

PRE-FINISHED NON-PERFORATEDCLOSURE FLASHING WITH 10° FALL

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 18 / 20

BOTTOM OF CLADDING (FLUSH)

2015

BUILDING PAPER OVER FLASHINGSHOWN DASHED

METALCRAFT MC760 VERTICALCLADDING

PRE-FINISHED SELF DRILLING / TAPPINGSCREW WITH RUBBER WASHER

PRE-FINISHED NON-PERFORATEDCLOSURE FLASHING WITH 10° FALL

MIN

. 75m

m C

OVE

R

3 - 5

mm

VEN

TILA

TIO

N G

AP

INTERNAL WALL LINING

PRE-PRIMED SKIRTING

CONCRETE SLAB

CAVITY CLOSER AS REQUIRED TONZBC

5 GAP

20

15

ALTERNATIVE OPTIONBIRDS BEAK EDGE

PRE-FINISHED FLAT HEAD WAFER-TEK SCREW FOR FLASHING

20mm CAVITY

MIN

. 50m

m L

AP

HEMMED EDGE

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760

- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.

ScaleDate Sheet

- CAVITY SYSTEM FOR VERTICAL CLADDING : 20mm NOMINAL THICK(VERTICALLY DRAINING) HORIZONTAL CAVITY SYSTEM WITH BATTENSAS APPLICABLE TO SUPPORT CLADDINGS & FLASHINGS TO NZBC.

1 : 2 19 / 20

BOTTOM OF CLADDING (RECESSED)

2015

Reference

DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRMcode of pratice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanismsis the responsibility of the designer. Construction detail can vary for wall cladding. The underlay isdetailed as a single line for simplicity and is indicative only. Building paper type and method ofinstallation should comply with underlay manufacturers recommendations and NZBC regulations.

COMMERCIAL VERTICAL CLADDINGMC760

CVMC760 ScaleDate Sheet 20 / 20

3D WINDOW FLASHINGS

2015

HEAD FLASHING

JAMB FLASHING

SILL FLASHING

FLUSH WINDOW FLASHINGS RECESSED WINDOW FLASHINGS

HEAD FLASHING

JAMB FLASHING

SILL FLASHING

METALCRAFTMC760 VERTICALCLADDING

ALUMINIUMWINDOWJOINERY

COMPRESSIBLEFOAM SEALBEHIND TO FILLOVERLAP OFFLASHING

ALUMINIUMWINDOWJOINERY

METALCRAFTMC760 VERTICALCLADDING