RX10 & RX12 Scissor Lifts Maximum Productivity, Minimum Space

RX Scissor Lift Large capacity with a small footprint

* Shown with protective cover removed.

4 24 in. runways accept wide vehicles

Extra-Wide Runways

24 in.

4 Maximize ground clearance

Best-In-Class Drive-On height

1110

98

76

54

32

112

1110

98

76

53

112

1110

98

76

54

32

112

11 in.OTHERS 10 in.

RX12 8.75 in.RX10

Two Swing Air Jacks

4 Convenient air source for tools at front and rear

Integrated Air Line Kit

4 Sensors keep runway level

4 Safely stops if obstructed

Sensor Feedback System*

4 Instantaneous shutdown in event of hydraulic failure

Velocity Safety Fuses Safety Locks

RX10LT-IS shown with optional light kit

4 6,000-lb. capacity

4 Technicians’ favorite

Two Swing Air Jacks

4 12 secure positions

4 Lightweight design

Two Movable Work Steps

4 Prevent wheel spin in wet conditions

4 More effective than diamond tread or abrasive strips

Louvered Ramps

4 Complete operation from the console

4 Optional PowerSlide, Inflation Station and FIA control

Control Panel

4 Precision-fit teeth lock runways at 16 level height positions

Safety Locks

4Chromed pins and teflon bearings for long life

Pins and Bearings

4 Automatically fills or bleeds each tire

4 No hanging air lines

Inflation StationOPTIONAL

The hydraulic system speeds lowering times by 50%.

The system automatically slows the descent in the last several inches to ensure a soft landing.

The fast descent feature is standard with Inflation Station (IS) models.

Fast descent speed

STANDARDFASTDescent0:25 0:50

Lifts may be flush-mounted in a shallow recess. No more worries about lowered vehicles or expensive spoilers! This very tidy installation is ideal for “showcase” shops.

No additional charge for flush-mount option. Contact your Hunter Sales Representative for details.

Add F to any RX model number.

Flush-mount installation

Hunter Swing Air Jacks add capabilities for lifting vehicles off the runways during alignment procedures and other multi-service operations.

Each 6,000-lb. (2722-kg) capacity Swing Air Jack combines low drive-on height with high lifting capacity needed to handle a wide range of vehicles.

133-85-1 – 6,000-lb. Capacity Swing Air Jack

Swing air jacks

Stage 2 RX approach ramp extensions

147-113-1 Standard with RX12A.Optional with RX10, adds 12.75 in. to length. (2 required)

20-2169-1 Adds 27.25 in. to RX10 or 22.25 in. to RX12A.

20-2189-1 Adds 37.25 in. to RX10 or 32.25 in. to RX12A.

Approach ramp extensions

OPTIONAL

Drive-thru conversion kit

20-2498-1 – RX10, RX12A and RX16 drive-thru kit for camera sensors adds 52 in. to overall length.

20-2501-1 – RX10, RX12A and RX16 drive-thru kit for conventional sensors adds 63 in. to overall length.

Conversion kits

OPTIONAL

Hunter’s integrated AlignLights LED lighting system provides a bright and efficient light source underneath the vehicle.

AlignLights automatically turns on when the lift is raised and turns off when the lift is lowered to the floor.

AlignLights is an ALI-listed accessory.

20-2766-1 – AlignLights system

AlignLights systemOPTIONAL

Standard equipment4 Flush-mounted, full-floating slipplates (PowerSlide slipplates on PS and IS models)

4 Two movable work steps (not included with flush-mount installations)

4 Louvered ramps with built-in wheel stops

4 Front wheel stops

4 Two wheel chocks

4Built-in, full-length jack rails

4Built-in air line kit

4 Stainless steel turnplates (PowerSlide turnplates on PS and IS models)

Shown with optional aligner console, sensors, bar code reader, target support brackets, and lights.

Hunter offers two fully integrated options to enhance productivity

FIA allows WinAlign® aligners to control the lift features for ultimate productivity. Two patented designs offer greater flexibility and timesaving capabilities.

** Requires FIA equipped aligner with WinAlign 10.x software or greater.

Printouts show starting and final tire pressures.**

P O W E R S L I D E E D I T I O N

I N F L A T I O N S T A T I O N E D I T I O N

4Includes PowerSlide® slipplates and turnplates

4Automatically inflate all four tires simultaneously

4Record starting and final pressure**

4Hose recoils to keep work area clear

4Locks slipplates and turnplates with the touch of a button or automatically through an FIA-equipped aligner**

4No more struggles with lock pins

4Avoid wear and tear and extend the life of your turnplates

Minimize trips around the car1 Mount targets

2 Make adjustments

3 Remove targets

4 Jack vehicle and compensate sensors

5 Lower leveling legs (if equipped)

6 Remove slipplate and turnplate pins

7 Replace slipplate and turnplate pins

8 Raise leveling legs (if equipped)

Only3 Trips!

1 23

Yesterday's Technology

8 Trips

8 76 5

4 32

1

Form 6175-T Ford, 12/14Supersedes Form 6175-T, 07/14

Copyright © 2014, Hunter Engineering Company

www.hunte r.com

16(406 mm)

IN.

22(559 mm)

IN.

24 IN.(610 mm)

LEAVE AMPLE WORKSPACE BETWEENEQUIPMENT AND LIFT RACK

7 FT. - 4 1/2 IN.(2248 mm)

FORRX10 MODELS,

IN.20 FT. - 1 1/4(6128 mm)

FORRX10L MODELS,21 FT. - 2 1/4 IN.

(6458 mm)

39 - 54(991 - 1372 mm)

IN.

PRIOR TO LIFT INSTALLATION:

INSTALL 230VAC, 1 PHASE,60 HZ FOR 26 AMP DRAW NEARCONTROL CONSOLE LOCATION.

90-150 PSI (6.2-10.3 BAR) SHOPAIR MUST ALSO BE SUPPLIED.

16(406 mm)

IN.

11 5/8 IN.(295 mm)

OPTIONALEXTENDED

WHEEL STOP

FORRX12A MODELS,

IN.22 FT. - 2(6756 mm)

Because of continuing technological advances, specifications, models and options are subject to change without notice.

See Hunter Sales Representative for details on site requirement.

RX Plan View

The Hunter RX10 and RX12A Scissor Lifts have been certified under the program conducted by Automotive Lift Institute (ALI) and ETL Testing Laboratories to comply with Safety Standard ANSI/ALI, ALCTV and Electrical Standard ANSI/UL 201.

SpecificationsRX10 RX10L RX12A

Max. vehicle weight 10,000 lbs. (4536 kg) 10,000 lbs. (4536 kg) 12,000 lbs. (5443 kg)

Max. wheelbase

General service 171/167 in. (4343/4241 mm) 184/180 in. (4673/4572 mm) 184/180 in. (4673/4572 mm)

Two-wheel alignment 166/162 in. (4216/4115 mm) 179/175 in. (4547/4445 mm) 179/175 in. (4547/4445 mm)

Four-wheel alignment 158 in. (4013 mm) 158 in. (4013 mm) 158 in. (4013 mm)

Min. Four-wheel alignment 88 in. (2235 mm) 88 in. (2235 mm) 88 in. (2235 mm)

Lowered height 8.75 in. (222 mm) 8.75 in. (222 mm) 10 in. (254 mm)

Max. lifting height 72 in. (1829 mm) 72 in. (1829 mm) 71 in. (1803 mm)

All models

Alignment height All lock positions

Runway width 24 in. (609 mm)

Tread width

Min. inside 40 in. (1016 mm)

Max. outside 88 in. (2235 mm)

Air pressure 90-150 psi (6.2-10.3 bar)

Speed55 seconds (raise)

25-50 seconds (descent)

RX10JT RX10 with (2) 6,000-lb. swing air jacks and stainless steel turnplates

RX10LJT Long-deck RX10 with (2) 6,000-lb. swing air jacks and stainless steel turnplates

RX10T-PSRX10 with (2) 6,000-lb. swing air jacks, PowerSlide slipplates and turnplates and FIA

RX10LT-PSLong-deck RX10 with (2) 6,000-lb. swing air jacks, PowerSlide slipplates and turnplates and FIA

RX10T-ISRX10 with (2) 6,000-lb. swing air jacks, PowerSlide slipplates and turnplates, Inflation Station and FIA

RX10LT-ISLong-deck RX10 with (2) 6,000-lb. swing air jacks, PowerSlide slipplates and turnplates, Inflation Station and FIA

RX12AJT RX12 with (2) 6,000-lb. swing air jacks and stainless steel turnplates

RX12AT-PSRX12 with (2) 6,000-lb. swing air jacks, PowerSlide slipplates and turnplates and FIA

RX12AT-ISRX12 with (2) 6,000-lb. swing air jacks, PowerSlide slipplates and turnplates, Inflation Station and FIA

Add F to any RX model number (ex. RX10LJFT) for flush-mount installation

Models

surface/flush

Contact your Ford Field Service Engineer or your Rotunda Area Sales Manager.

1-800-ROTUNDA www.OneRotunda.com