Rubber Torsion Axle and Trailer Components Torsion Axle and Trailer Components Phone Email Web 9...
Transcript of Rubber Torsion Axle and Trailer Components Torsion Axle and Trailer Components Phone Email Web 9...
Rubber Torsion Axle and Trailer Components
Phone
Web
9 Lathams Road , Carrum Downs , VIC 3201
03 9775 1762 Fax: 03 9775 [email protected]
1
�
Transtyle Rubber Torsion Axle
If you’re looking for a softer, high quality ride, without ongoing maintenance and repairs, look no further than Transtyle Rubber Torsion Axles. Transtyle rubber torsion axles offer a significant improvement to ride quality in comparison to the conventional spring axles because both sides of the axle operate independently from each another. The rubber elastomer springs also help to smooth out the ride by absorbing at lot of the bumps; hence it is also a quieter ride. Our axles are virtually maintenance free and have no leaf springs that will rust.
How does the Rubber Torsion System Work?
Four natural rubber cords within the main structure of the axle beam surround the steel torsion bar. The wheel/hub spindle is attached to a lever, called the torsion arm assembly. This assembly comprises of the torsion arm, torsion bar and spindle. When load is applied to the trailer the torsion arm assembly pivots around the torsion bar, causing a rolling or compressive resistance in the rubber cords inside the axle beam.
����
Spindle
Brake flange
Bracket
Inner shaft
Axle beam
Rubber cord
Torsion armStainless steel wear sleeve
2
�
���������������������
A����������������������������� ������BB���� ����>���
����������� �������� P������ � ����QS�����T�U�SSS����W�� ���X���Y
����������� ������� P������ � ���U�ZQS����T�U�QSS��������U��SS���
����������� ������� P������ � ���Z�SSS���T�Z�ZSS��������Z�QSS���
����������� �������� P������ � ���Z��QS��������[�SSS���
A��������BB���� ����>������� ��B������������������� ��?�A������������� ���������� ��
$�'�#�=�!E#�(!"�\#�=��#J'!!#+�#���#-=���'�#J';�=N#&�#�!�"����'8"!�#��#�#E$!!#%"�/#�(!"N#J='-=#'�#�8�'!�%!"#
�����X�� �����>������]�X�����>�?��A��]�������>�� ���������B������ ������ ������������B����
�&#�'�#!&J"�#&�#�="#���'!"�H##�="#�(!"#%"�/�#��"#"'�="�#=&�#;'4#*�!8��'^";#&�#"!"-��&4!��";#+�'�=#E&�#
-&��&�'&�#4�&�"-�'&�H##_!!#&E#&$�#�&��'&�#��/�#��;#'��"�#/"��!#�=�E��#��"#;�-�&/"�#4!��";#+�'�=#E&�#
����� ������ �������� ���
������������������O����� ��������������� ��>����� ������������������������ZQ`������ ���>������� ��
b����K����[�SSS��������gAj��������� ��������>������ZSSS��������� ������� ���� �?�
�������������������O�����������B������>����������� ������������������������� � �������USS�������
��������������������������?�
������!"�����������
_!!#&E#&$�#�(!"�#-&/"#J'�=#&$�#�������!"#k�"��"#(-=��*"#����"/H#�='�#����"/#'�#�="#/&��#")"-�'8"#
�����������������B� ����������� ��������������������?�
'�=#�="#�������!"#k�"��"#(-=��*"#����"/N#*�"��"#'�#4$/4";#�=�&$*=#�="#=$%#8'�#�="#*�"��"#^"�p#
�����������������������������?�q��� ������������������B� ������������������> ������
��#�="#�"��#&E#�="#�4'�;!"H#��$�"#�=��#�="#�"�!#4!$*#=��#%""�#�"/&8";#�&#�!!&J#�="#*�"��"#�&#v&J#
������?
z���������������� �� �������B� ���������������> ��������������������������� ���?��
�&��'�$"#�$/4#�"J#*�"��"#�=�&$*=#�="#����"/#$��'!#�&$#��"#�%!"#�&#�""#�#��"�;�#v&J#&E#�"J#
������� ����������> ����������������
�� ���� ��� ������������������������������
=��#%""�#v$�=";#&$�H##��-"#!$%�'-��'&�#'�#
������������������������?
O����� ��������������� ��>����� ������������������������ZQ`������ ���>������� ��
����gAj��������� ��������>������ZSSS��������� ������� ���� �?b����K����[�SSS����
When using for tandem axle trailers, it must allow for 20% decrease in axle capacity. Eg = two axles 2,500 kgs capacity will be suitable for 4,000 kgs ATM tandem trailers. And 25 % for tri-axle trailers. Eg = three axles 2,000 kgs capacity will be suitable for 4,500 kgs.
Removable Seal Plug
3
TWO PIECE TORSION AXLE TECHNICAL INFORMATION
DIMSERIES 2 AXLE
1250 KG - 1500 KG -1700 KGSERIES 3 AXLE
2000 KG - 2200 KG - 2500 KGSERIES 4 AXLE
2750 KG - 3000 KG
A
B
C
D
E
F
212
470
340
110
65
620
242
550
340
120
75
730
242
550
340
135
90
730
TWO PIECE AXLE DIMENSIONS (MM)
A
B
C ( MIN)
DE
12.50
(F)
85.0
(20)
5
��
��������������������Torsion Axles Order Information �
��������� �
�� ���������� ����������� �
�� ����� ����������������������������������������������������������������������
�� �������������� ���!���"� #���$�������������������������������� ��%����������
�&����� '������ � �&�(������������������������ �&�)#���*����������
���%������ +�����%������������������(�������%�������������, ����������%�����
���%��)������ ����� �������� ��� ��������
����� �������� ��� ���������%������
����� �������� �*����������������������������������������������������������������������
������ ��)� �&�������-�&�����������
����%�������� ����!��!�������������������������.�!�����
)����!������%�������
)����!������%����
����������!#���������������������������������������
�&�������������������������
�&������
����������!#��������������������������������������
+����/��.����������0������!������� ������������ ���0���123�!������������� �������������!�143�
0������5�� ������� ���
����!�������&� ����� �����������0������� �&�0������� �&�0������!�)����!������%������
)����!�������%�����������������
�
�� �Axle Series Axle Style Hub Face (Min) Overhang (Min) Series 2 Straight Axle 1250mm 155mmSeries 2 VShape Axle 2100mm 155mm Series 3 & 4 Straight Axle 1250mm 195mm Series 3 & 4 VShape Axle 2100mm 195mm
��
�9
Series #2 Axles components
Hub and Rotor
Lazy Hub ( Hot Dip Galvanize ) Ford 5 Stud Pattern Complete with Bearings, Seal and studs Inner bearing = L68149 / Cup L68111 Outer bearing = L 44649/ Cup L44610 Seal = 171255 UC /TC Part Number = HB1002
UFP 9.75” Integral Hub (Dacromet Plated) Ford 5 Stud Pattern Complete with Bearing, Seal and Studs Inner bearing = L 68149/ Cup L68111 Outer bearing = L 44649/ Cup L44610 Seal = 171255 UC /TC Part Number = HB0975
10” Integral Hub (Dacromet Plated) Ford 5 Stud Pattern Complete with Bearing, Seal and Studs Inner bearing = L 68149/ Cup L68111 Outer bearing = L 44649 / Cup L44610 Seal = 171255 UC /TC Part Number = HB1001
10” Electric drum/hub (Painted ) Ford 5 Stud Pattern Complete with Bearing, Seal and Studs Inner bearing = L 68149/Cup L68111 Outer bearing = L 44649/Cup L44610 Seal = 171255UC/TC Part Number = HB1003 10
10” Vsuit 24mFord Part 10” Vsuit Ford Part K22SingStainBrasBrakSuita Part K22StainSingStainBrasSuita Part UFPAlumBrakSuita( No Part
Ventilated for hub ovmm thickned 5 studs pat Number =
Ventilated Hub Over d 5 Stud Pat Number =5 Caliper agle Stainlessnless Steel ss Fittings,ke Pads Incable for 10t Number =5 Caliper anless steel gle Stainlessnless Steel ss Fittings, able for10”t Number = DB35 Alumminum Pistke pad incluable for 9.7ote ) R/H ant Number =
rotor ( Dacer rotor, ss attern = DR1001
Rotor ( StaRotor attern = DR1002 assembly (Ds Steel PistSlider Sleecluded ” and 12” R= CP1001 assembly ( SBody s Steel PistSlider SleeBrake Pads” and 12”Ro= CP1002 minum Caliton uded 75’ UFP disnd L/H diff= CP1003
cromet )
ainless Stee
Dacromet pton, eve, Rotor24mmStainless Stton, eve s Included.otor24mmTiper Body c 22mm thferent parts
el )
plated ) mThicknessteel ) Thickness
hick s
s
11
CalipSuitaCalip Part CalipSuitaCalip Part CalipSuitaCalip Part
per Mountiable for 10per t Number =
per Mountiable for 10per t Number =per Mountiable for 10per t Number =
ing Bracket” Integral R= BR1001
ing Bracket” Hub Over= BR1002 ing Bracket” Hub Over
= BR 1003
t ( DacromRotor with
t (Dacromer Rotor wit
t (Stainlessr Rotor wit
et Plated)K225
et Plated) th K225
s Steel) th K225
12
Series #3 and #4 Axles components
12” Lazy Hub (Hot Dip Galvanize ) Land cruiser 6 Stud Patten Complete with Bearings, Seal and Studs Inner bearing = 25580/Cup 25520 Outer bearing = 15123 /Cup 15245 Seal = 225255 Part Number = HB1202
12” Integral Hub (Dacromet Plated) Land cruiser 6 Stud Pattern Complete with Bearing, Seal and Studs Inner bearing = 25580/Cup 25520 Outer bearing = 15123/Cup 15245 Seal = 225255UC Part Number = HB1201
12” Electric drum /hub (painted ) Complete with Bearing, Seal and Studs Landcruiser 6 Stud Pattern Inner bearing = 25580/Cup 25520 Outer bearing = 15123/Cup 15245 Seal = 225255UC Part number = HB 1203
12” Ventilated Rotor ( Dacromet Plated ) Suitable for hub over rotor , 24mm thickness Landcruiser 6 Stud Pattern Part Number = DR1203
13
12” Vesuitabl24mmLandcr Part N K225 CSingle StainleBrass FBrake Suit fo Part N K225 CStainleSingle StainleBrass FSuit fo Part N CaliperSuitabIntegr Part N CaliperSuitabwith 2 Part N
entilated Role for Hub m thickness ruiser 6 Stuumber = DCaliper asseStainless Sess Steel SliFittings, Pads Includr 10” and 1umber = CPCaliper asseess steel BoStainless Sess Steel SliFittings, Brr10” and 1umber = CPr Mountingble for 12” Hral Rotor, wumber = BR
r Mountingle for 12” H25 CaliperNumber = B
otor ( StainOver Rotor ud Pattern R1202 embly (DaSteel Pistonider Sleeve ded 12” Rotor24P1001 embly ( Staody Steel Pistonider Sleeverake Pads In2”Rotor24P1002
g Bracket (Hub Over Rwith 225 CaR1201
g Bracket (Hub Over RBR1202
nless Steel )r
acrometplatn, e, 4mmThickainless Steen, e ncluded. mmThickn
(Dacromet Rotor and liper
(Stainless SRotor and In
)
ted ) kness el )
ness
Plated)
Steel) ntegral Rot
tor,
14
Stainless Steel Caliper Mounting Bolt Bolted caliper to caliper mounting bracket Set of 2 bolts for 1 caliper Part Number = BP1002
15
Hubs and rotors
Complete 12” Stainless Steel Brake Kit Includes: 1 x Stainless Steel 12” Rotor 1 x Stainless Steel 225 Caliper 1x Stainless Caliper Bracket Land cruiser 6 studs Patten (Hub Shown in Picture not include ) Part Number = BS 1002
Complete 10” Stainless Steel Brake Kit Includes: 1xStainless Steel 10” Rotor 1x Stainless Steel 225 Caliper 1x Stainless Caliper Bracket Ford 5 studs Patten (Hub Shown in Picture not include ) Part Number = BS 1001
10” Integral Hub (Dacromet Plated) Ford 5 Stud Pattern Complete with Bearing, Seal and Studs Inner bearing = L 68149 /Cup L68111 Outer bearing = L 44649/Cup L44610 Seal = 171255UC/TC Part Number = HB1001
12” Integral Hub (Dacromet Plated) Land cruiser 6 Stud Pattern Complete with Bearing, Seal and Studs Inner bearing = 25580/Cup 25520 Outer bearing = 15123/Cup 15245 Seal = 225255U Part Number = HB1202
16
UFP 9.7” Integral Hub ( Dacromet Plated ) 5 Stud Ford Pattern Complete with Bearing, Seal and Studs Inner bearing = L 68149 /Cup L68111 Outer bearing = L 44649/Cup L44610 Seal = 171255UC/TC Part Number = HB0975
10” Lazy Hub (Hot Dip Galvanize ) Ford 5 studs Patten Complete with Bearings, Seal and Studs Inner bearing = L68149/Cup L68111 Outer bearing = L 44649/Cup L44610 Seal = 171255UC/TC Part Number = HB1002
12” Lazy Hub (Hot Dip Galvanize) Land cruiser 6 Stud Patten Complete with Bearings, Seal and Studs Inner bearing = 25580/Cup 25520 Outer bearing = 15123/Cup 15245 Seal = 225255U Part Number = HB1202
10” Ventilated rotor (DacrometPlated ) Suitable for Lazy Hub ( hub over rotor ) 24mm thickness Ford 5 studs pattern Part Number = DR1001
10” Stainless Steel Ventilated Rotor Suitable for Lazy Hub ( Hub Over Rotor ) Ford 5 Stud Pattern Part Number = DR1002
12” Ventilated Rotor (DacrometPlated ) Suitable for Lazy Hub (Hub over rotor) 24mm thickness Landcruiser 6 Stud Pattern Part Number = DR12001 17
12” Stainless Steel Ventilated Rotor Ssuitable for Lazy Hub ( Hub Over Rotor ) 24mm thickness Landcruiser 6 Stud Pattern Part Number = DR1202
10” Electric drum/hub (Painted ) Complete with Bearing, Seal and Studs Ford 5 Stud Pattern Inner bearing = L 68149/Cup L68111 Outer bearing = L 44649/Cup L44610 Seal = 171255UC/TC Part Number = HB1003
12” Electric drum /hub (painted ) Complete with Bearing, Seal and Studs Landcruiser 6 Stud Pattern Inner bearing = 25580/Cup 25520 Outer bearing = 15123/Cup 15245 Seal = 225255U Part number = HB 1203
Bearings Set suitable for 10” Hub Including Bearing and Seal Inner bearing = L68149 /Cup L68111 Outer bearing = L44649/Cup L44610 Seal = 171255UC/TC Part Number = BB1001
Bearings Set suitable for 12” Hub Including Bearings and Seal Inner bearing = 25580/Cup 25520 Outer bearing = 15123/Cup 15245 Seal =225255UC Part Number = BB1002
18
Grease Cap 50mm suitable for 10” Hub Part Number = CR1001
Grease Cap 62mm suitable for 12” Hub Part Number = CR1002
Transtyle Oil Bearing lubrication 50mm Suitable for 10” Hub Set of 2 for 1 axle Part Number = CR1003
Transtyle Oil Bearing lubrication 62mm Suitable for 12” Hub Set of 2 for 1 axle Part Number = CR1004
Stainless Steel Bearing Buddy 50mm Part Number = CR1005 Stainless Steel Bearing Buddy 62mm Part Number = CR 1006
19
Brake Components
Dexter Brake actuator 1600psi Suitable for 2 to 6 Wheels Disc Brakes Part Number = DT1001
Breakaway Kit ,9 Amp/Hour Including: Battery, Battery Carry Box , Safety Switch Part Number = DT1002
AL/KO SensabrakeIQ7 1000psi suitable for Tandem Axles Part Number = DT1003
Dexter Brake Controller DX2 suitable for Dexter Brake Actuator Parts Number = DT1004 20
Tekonsha Brake controller Primus 90160 Part Number =DT1005
10” Electric backing plate brake assembly (with hand brake ) Part Number = EB0001
12” Electric backing plate brake Assembly ( with hand brake ) Part Number =EB0002
Brake Master Cylinder 3/4” Part Number = BM1001
Brake Master Cylinder 7/8” Part Number = BM1002
21
Brake 3/4” BPart N 7/8” BPart N 1” BrPart N
OverrCylindAvaila3/4” BPart N 7/8” BPart N 1” Bra Part N Brake Part N K225 SingleSleeveBrakeSuitab Part N K225 StainlSingle StainlBrass Suit fo Part N
e Master Cy Available Brake MasNumber=BMBrake MastNumber=BMrake MasteNumber=BMride Couplider able with Brake MasNumber=BMBrake MastNumber=BMake Master Number=BMe Master CyNumber = B
Caliper asse Stainless Se, Brass Fite Pads Incluble for 10” aNumber = CCaliper assess steel Boe Stainless Sless Steel SFittings, Bor10” and 1Number = C
ylinder Kit with ter CylindeM1004 ter CylindeM1005 r Cylinder M1006 ng kit withter CylindeM1007 ter CylindeM1008 Cylinder M1009
ylinder BracBM1010 sembly (DaSteel Pistonttings, uded and 12” RoCP1001 sy ( Stainleody Steel PistonSlider Sleevrake Pads I12”Rotor24CP1002
er r
h Brake Maer r
cket
acromet pln, Stainless otor 24mmss Steel ) n, ve Included. 4mmThickn
aster
ated ) s Steel Slidem thick
ness
er
22
UFP DB35 Aluminum Caliper Body Aluminum Piston Brake pad included Suitable for 9.75’ UFP disc 22mm thick ( Note ) R/H and L/H different parts Part Number = CP1003
Ceramic Brake Pad suit for Kodiak 225 Caliper Set for 2 calipers Part Number = BP1001
Stainless Steel Mounting Bolt 11mm Bolts Caliper to Mounting Bracket (set of 2) for 1 caliper Part Number = BP1002
Stainless Steel Caliper 225 Piston Part number = BP1003
Bleeder (Brass) suitable for 225 Caliper Part number = BP1004
L Connector (Brass) Connects Hydraulic Brake Line to Caliper Part number = BP1005
23
Brake Line adapter ( Brass ) Part Number=BP1006
Brake Line straight Join ( Brass) Part Number=BP1007
24
Caliper Brackets
Caliper Mounting Bracket (Dacromet Plated) Suitable for 10” Integral Rotor with K225 Caliper Part Number = BR100
Caliper Mounting Bracket (Dacromet Plated) Suitable for 10” Hub Over Rotor with K225 Caliper Part Number = BR1002
Caliper Mounting Bracket (Stainless Steel) Suitable for 10” Hub Over Rotor with K225 Caliper Part Number = BR100
Caliper Mounting Bracket (Dacromet Plated) Suitable for 12” Hub Over Rotor and Integral Rotor, with 225 Caliper Part Number = BR1201
Caliper Mounting Bracket (Stainless Steel) Suitable for 12” Hub Over Rotor and Integral Rotor, with 225 Caliper Part Number = PR1202
25
Stainless Steel Braided Flexible Brake Line
SAVE TIME AND MONEYBY USING TRANSTYLE FLEXIBLE BRAKE LINES. THIS IS A MORE EFFICIENT METHOD OF INSTALLING HYDRAULIC BRAKE LINES – NO SPECIAL EQUIPMENT NEEDED AND LESS FITTINGS ARE REQUIRED.� TRANSTYLE FLEXIBLE BRAKE LINES WITH THE STAINLESS STEEL CONNECTOR WILL NOT RUST AND IS ABLE TO HOLD PRESSURE UP TO 3000 PSI.
Braided Stainless Steel Flexible Brake Line With Stainless Steel Connector 600mm Length Part Number = FB0600 26
Braided Stainless Steel Flexible Brake Line With Stainless Steel Connector 1300mm Length Part Number = FB1300
Braided Stainless Steel Flexible Brake Line With Stainless Steel Connector 2000mm length Part Number = FB2000
Braided Stainless Steel Flexible Brake Line With Stainless Steel Connector 5500mm Length Part Number = FB550
Braided Stainless Steel Flexible Brake Line With Stainless Steel Connector 6500mm length Part Number = FB6500
3 Ways Connector Stainless steel Part Number = CB0003
4 Ways Connector Stainless Steel Part Number = CB0004
27
Single Axle Kit Braided Stainless Steel Flexible Brake Line - Single Axle Kit Kit Consists of the Following: 1 x 5500mm Flexible Line 1 x 2000mm 1 x 500mm 1 x 3 Way Connector Part Number = FB0001
Tandem Axles Kit Braided Stainless Steel Flexible Brake Line Tandem Axles Kit Kit Consists of the Following 1 x 5500mm Flexible Line 1 x 2000mm 2 x 1300mm 2 x 600mm 1 x 3 Way Connector 1 x 4 Way Connector Part Number = FB0002
28
Tri Axles Kit Braided Stainless Steel Flexible Brake Line Tri Axle Kit Kit Consists of the Following: 1 x 6500mm Flexible Line 2 x 2000mm 2 x 1300mm 4 x 600mm 2x 4 Way Connector 1 x 3 Way Connector Part Number = FB0003
29
Couplings / Jockey wheels / Winches
Non Brake Coupling suit for 50mm Tow Ball Capacity 2000kg Part Number = CL0001
Override Coupling suit for 50mm Tow Ball Capacity 2000kg Part Number = CL0002
Electric Coupling suit for 50mm Tow Ball Capacity 3500kg Part Number = CL0003
Electric Coupling suitable for 70mm Tow Ball Capacity 4500kg Part Number = CL0004
Tow Ball 70mm capacity 4500kg Parts Number = CL0005
Tow Ball 50mm capacity 3500kg Part number = CL0006 30
Stinger 150mm Drop When only the best will do! The perfect drop bar for boat, RV, horse float, any towed mass. Solid bar aluminium fits a 2" (50mm) standard receiver. Tow Rating 2.9T Part Number = CL0012
Rapid Hitch Specifications • 4" Rapid Hitch • 50mm Chromed Tow Ball • Fits Standard 2"/50mm receiver • 3500kgs Trailer GVW • Aluminium Super Alloy (Solid Bar) • 30% Stronger than Steel • ADR Approved Tow Balls • Polished Finish Match Locking Keys Part number = CL0007
Rapid Hitch Specifications • 4" Rapid Hitch • 50/70mm Chromed Tow Ball • Fits Standard 2"/50mm receiver • 4500kgs Trailer GVW • Aluminium Super Alloy (Solid Bar) • 30% Stronger than Steel • ADR Approved Tow Balls • Polished Finish • Match Locking Keys Part Number = CL0008
Rapid Hitch Specifications • 6" Rapid Hitch • 50/70mm Chromed Tow Ball • Fits Standard 2"/50mm receiver • 4500kgs Trailer GVW • 250mm Vertical Adjustment • Aluminium Super Alloy (Solid Bar) • 30% Stronger than Steel • ADR Approved Tow Balls • Polished Finish • Match Locking Keys Part Number = CL0009
31
Stinger 50mm Drop When only the best will do! The perfect drop bar for boat, RV, horse float, any towed mass. Solid bar aluminium fits a 2" (50mm) standard receiver. Tow Rating 2.9T Part Number = CL0010
Stinger 100mm Drop When only the best will do! The perfect drop bar for boat, RV, horse float, any towed mass. Solid bar aluminium fits a 2" (50mm) standard receiver. Tow Rating 2.9T Part Number = CL0011
Fulton Jockey Wheel F2 Fulton Jockey wheel 750kg Part Number =JK 0001
Fulton Jockey Wheel 680KG Part Number = JK 0002
32
Fulton Jock Part Numb
Bulldog Pa4500kg Part Numb
AL/KO Joc500kg Part Numb
AL/KO Joc300kg 250 Part Numb
key Wheel Fber = JK 000
ark Leg - SQ ber = JK 000
ckey Wheel ber = JK 000
ckey Wheel 0mm wheel ber = JK 000
F2 Swivel Pl03
SW Side - 04
Auto Retra05
with Clam 06
late
ct
mp
33
Trojan Swing up Jockey Wheel 120kg 150mm Solid rubber wheel Part Number = JK0007
ARK Swing up Jockey Wheel 500kg 200mm solid Rubber Wheel Part Number= JK0008
AL/KO Boat Winch Heavy Duty Gear Ratio 10: 1 / 5 :1 / 1 : 1 Part Number= WK 0001
AL/KO Boat Winch Heavy Duty Gear Ratio 5 : 1 / 1 : 1 Part Number =WK 0002
AL/K0 Boat Winch Heavy Duty 1200kgGear Ratio: 15:1, 5:1 and 1:1 Part Number = WK 0003 34
F2 Fulton T Part Numb F2 Fulton T1450kg Part Numb F2 Fulton T2 speed , 1 Part Numb Fulton Tra Part Numb
Trailer Winber =WK 00
Trailer Winber =WK 00Trailer Win1450kg
ber = WK 00
ailer Winch ber = WK 00
nch 900KG004
nch Heavy D005 nch Heavy D006
800kg 007
Duty
Duty
35
ROLLERS AND BRACKETS
Keel Roller 12” Polyurethane , Suitable for Fiberglass Boats Pin Hole = 26mm Part Number = RL0001R
Keel Roller 12” Polyurethane , Suitable for Fiberglass Boats Pin Hole = 26mm Part Number = RL0001B Keel Roller 12” Polyurethane , Suitable for Fiberglass Boats Pin Hole = 26mm Part Number = RL0001C
Keel Roller 8” Polyurethane , Suitable for Fiberglass Boats Pin Hole = 16mm Part Number = RL0002B
Keel Roller 8” Hard Plastic Suitable for Aluminium Boats Pin Hole = 16mm Part Number = RL0002
36
Wobbler Roller Part Number = RL0003
V Roller Set 3 Piece Suitable for all Boat Types Part Number = RL0017
V Block Soft Poly Suitable for all Boat Types Part Number = RL0016
Heavy duty V Block Poly Suitable for all Boat Types Part Number = RL0018
Keel Roller Shaft 24mm Galvanized Suitable for 12” Keel Roller Complete with washer and pin Part Number = RL0012
Keel Roller Shaft 16mm Galvanized Suitable for 10” Keel Roller Complete with washer and pin Part Number = RL0013
37
Single Wobble Roller Arm Set Part Number = RL0004 Note : Sale as loose parts
Single Swing Arm Wobble Roller Set Part Number = RL0005 Note : Sale as loose parts
Double Swing Arm Wobble Roller Set Part Number = RL0006 Note : Sale as loose parts
Double Wobble Roller Swing Arm Galvanized Part Number = RL0007
Single Wobble Roller Swing Arm Galvanized Part Number = RL0008
Swing Arm Bracket (Galvanized ) Set of Two Suit 50mm to 75mm s/q Cross Member Part Number = RL0009 38
Wobbler Roller Swing Plate Galvanized Part number = RL0010
Galvanize Backing Plate 10mm Thick Suitable for 40mm skids support with 75mm cross member 12mm holes Parts Number = RL0018
Galvanize Backing Plate 10mm Thick Suitable for 40mm skids support with 90mm cross member 12mm holes Parts Number =RL0019
Swing Plate Rubber Cushion Price Per Meter Part Number = RL0011
Aluminum Single Keel Roller Set 12” Part Number = RL0014
Aluminum Single Keel Roller Set 12” with Side Bracket Part Number = RL0015
39
Aluminum front V support ( Front Center Guide ) Part Number = AP001
Aluminum Keel Roller Support 12” with Side Bracket Part Number = AP0011
Aluminum Center Guide Support Bracket Part Number = AP001
Aluminum Skids Support Set Suitable for 40mm x 90mm Transtyle Plastic Skids Sale with bolts Part Number = AP0013
Aluminum Skids Support Set Suitable for 65mm x 90mm Transtyle Plastic Skids Sale with Bolts Part Number = AP0014
Aluminum Skids Bracket Suitable for 40mm x 90mm Transtyle Plastic Skids Part Number = AP0015
40
Aluminium Skids Bracket Suitable for 65mm x 90mm Transtyle Plastic Skids Part Number = AP0016
Aluminum Skids Support Post Size 40mm x 40mm Parts Number = AP0017 Price : $ 15.00 +gst
Aluminum Keel Roller Ladder Suitable for 200mm Keel Rollers Roller Shaft 16mm Length = 3.0m Number Rollers = 13 Note : Sale with without rollers Part Number= AP001
Aluminum Keel Roller Ladder Suitable for 300mm Keel Rollers Roller Shaft 24mm Length = 3.45m Number Rollers = 11 Note : Sale without rollers Part Number= AP0019
Transtyle Plastic Skids Size 40mm x 90mm x 3.6m Part Number =PL0001
41
Transtyle Size 65mm Part Numb We carry a Stainle Bolts andPrice sale SS - UM10X25XM10X45X1M10X75X9M10X85X1M10X85X1M12X40X1M12X40X1M12X75X1M12X75X1M12X88X1M12X100XM12X105X
Plastic Skidm x 90mm xber = PL000all different ess Steel d U Bolts inwith nuts aU BOLTS 60mm 115mm 90mm 110mm 120mm 140mm 155mm 100m 175mm 185mm X135,mm X240mm
ds x 3.6m 02 size of stock and washer
42
Wheels and Tyres Aluminium Wheel Rim 14x6 Offset = 0 Ford 5 Stud Pattern Load capacity = 865kg Part Number = WR 0001 Available with L/T Tire Fitted
Aluminium Wheel Rim 15x6 Offset = 0 Land cruiser 6 Stud Pattern Load capacity = 1185kg Part Number = WR 0002 Available with L/T Tire Fitted
Aluminium Wheel Rim 15x6.5 Offset = -10 Landcruiser 6 Stud Pattern Load capacity = 1185kg Part Number = WR 0003 Available with L/T Tire Fitted
Aluminum Wheel Rim Size available : 13X5 , 5 Studs Capacity = 750kg 14X6 , 5 Studs Capacity = 1000kg 15X7 , 6 Studs Capacity = 1,200kg Part Number = WR 0004 A Part Number = WR 0004 B Part Number = WR 0004 C * Available with L/T Tire Fitted 43
Aluminum Wheel Rim Size available : 14X6 , 4 and 5 Studs Capacity =1050kg Parts Number = WR 0005 * Available with L/T Tire Fitted
Aluminum Wheel Rim Size available : 16X8 , 5 and 6 Studs Capacity =1200kg Parts Number = WR 0006 * Available with L/T Tire Fitted
Aluminum Wheel RimSize available : 13X5 , 4 and 5 Studs Capacity= 830kg Parts Number = WR 0007A 14X6 , 4 ,5and6 Studs Capacity=1050kg Parts Number = WR 0007B 15X7 4 ,5and6 Studs Capacity=1400kg Parts Number = WR 0007C 16X8 4 -5and6 Studs Capacity=1400kg Parts Number = WR 0007D 17X8 5 and 6 Studs Capacity= 1400kg Parts Number = WR 0007E Available with L/T Tire Fitted
Aluminium Wheel Rim Size 13x5 Offset = 0Ford 5 Studs Load capacity 750kg Part Number = WR 0008A Aluminium Wheel Rim Size 14x6 Offset = 0 Ford 5 Studs Load capacity 865kg Part Number = WR 0008B Aluminium Wheel Rim Size 15x6.5 Offset = 0 Landcruiser 6 Stud Pattern Load capacity = 1185kg Part Number = WR 0008C Available with L/T Tire Fitted Chrome Wheel Nuts suitable for all of the above alloy rims are available 44
Aluminium Fenders and Brackets Aluminium Tread Plate. Single Fender suitable for 13” and 14” wheel. Length = 750mm Height = 370mm Width = 230mm Thickness = 3.0mmPart Number : AP0001
Aluminium Tread Plate. Single Fender suitable for 14” and 15” wheel. Length = 800mm Height = 370mm Width = 240mm Thickness = 3.0mm Part Number : AP0002
Aluminium Tread Plate. Double Fender suitable for 13” and 14” wheel. Length = 1550mm Height = 450mm Width= 245mm Thickness = 3.5mm Part Number : AP0003 Aluminium Tread Plate. Double Fender suitable for 14” and 15” wheel. Length = 1600mm Height = 450mm Width= 250mm Thickness = 3.5mm Part Number : AP0004 45
Aluminium Tread Plate. Three Axle Fender suitable for 14” and 15” wheel. Length = 2380mm Height = 450mm Width = 250mm Thickness =3.5mm Part Number = AP0005 Fender Bracket suitable for all fender above Length = 450mm Width = 100mm Height = 45mm Thickness = 6mm Parts Number = AP0006 Aluminium Winch Post suitable for 100mm Draw Bar. Height = 800mm Size 100mm x 100mm x 6mm thick Part Number: AP0007 Aluminium Winch Post suitable for 100mm Draw Bar. Height = 800mm Size 100mm x 100mm x 6mm thick Part Number: AP0008
46
Aluminium Winch Post suitable for 75mm Draw Bar. Height = 800mm Size = 75mm x 75mm x 6mm thick Part Number : AP0009 Aluminium Winch Stand suitable for 100mm Winch Post. Part Number: AP0010 Aluminium Winch Stand suitable for 75mm Winch Post. Part Number : AP0011 Aluminium Spare Wheel Hanger suitable for 13” -14” and 15” Tyre. Part Number : AP0012
47
LED Lighting
LED Tail Lamp Set Fully Waterproof and Submersible ADR Compliant. Suits 12v Option of round or rectangular plug �Comes with 8M cables from lamp to gooseneck, 2.1m and 2m electric cable to the plug. Part Number = LE0001
LED Tail Lamp L/H Fully Waterproof and Submersible ADR Compliant. Suits 12v Size: 200x113x28mm Part Number = LE0002 LED Tail Lamp R/H Number plate light include Part Number = LE0003 LED Side / Clearance Lamp Fully Waterproof and Submersible. ADR compliant. Suits 12v Option of Red, Yellow or Clear Part Number = LE 0004R LE 0004W LE 0004A
48
LEDPart Traito sq Part Traito Rou Part
D Number Pt Number =
iler Plug Adquare plugt Number =
iler Plug Adund plug t Number =
Plate Light = LE0005
dapter fromg = LE0006
dapter from= LE0007
m 7 pins ro
m 7 pins sq
und
uare
49
All orders received by Transtyle Australia are an indication that the customer had read, fully understands, and accepts all of the terms and conditions of this warranty policy.
This warranty policy is applicable only to spare parts and does not apply to trailers purchased from Transtyle Australia.
(1) Warranty CoverageTranstyle Australia warrants their products to be free from defects in workmanship and material under normal use and service. The use of these products for other than their intended use or any alternations made to a product will render void all terms of this warranty.The exclusive remedy offered under this warranty is repair or replacement of the defective item only. Transtyle Australia shall determine and their discretion, whether repair or replacement is appropriate. Transtyle Australia’s obligation under this warranty is limited to the repair or replacement of the defective part and is not liable for any incidental or consequential damage to property or persons. On discovery of any defect in the Goods, the Customer must immediately notify the Company in writing of such defect.
consent of the Company to do so. Any avoidable consequential damage arising as a result of failure to seek advice from Transtyle will render any warranty claim invalid and void.These Terms do not affect the rights, entitlements and remedies conferred by the Trade Practices Act 1974.
(2) Warranty DurationThe warranty periods listed below are effective from the date of original invoice and extends only to the original purchaser of the product only.All parts in this catalogue are covered with a 12 month warrant.With the exception of the following:
(a) Rubber Torsion Axles5 yrs: Torsion axle beams from structural defects5 yrs: Torsion axle arms from structural defects2 yrs: Torsion axle rubber cordsNot covered: Wheel bearings, seals, spindles and brake pads.
(3) Warranty ExclusionsThis warranty does not extend to or cover defects caused by:• Normal usage wear and tear• Unreasonable operation and/or use• Accidents• Off-road use• Failure to provide reasonable and/or necessary maintenance• Improper installation or assembly performed by another party other than Transtyle Australia.• Any alterations made to parts supplied• Non standard production parts• Improper wiring of the brakes to the trailers or tow vehicle• The attachment of the axle assembly to the trailer• Alignment• Improper wheel nut torque• The welding of supplemental mounting brackets or members to exiting axle beam• Transtyle Australia will not be responsible for additional costs incurred for replacement, removal or reinstallation
of any parts supplied. This includes but is not limited to towing costs, storage costs, labour costs, travel costs, postage and freight costs, loss of income or any other cost or loss incurred. The liability of Transtyle Australia is limited to the repair or replacement of the product purchased only.
(4) Warranty Service
To obtain warranty service, the following information must be supplied by the purchaser:• Proof of purchase• Full contact details of purchaser• Where applicable, serial number, of product• Detailed description of the defect
50