Rtd
-
Upload
narendra-kumar-dewangan -
Category
Technology
-
view
5.258 -
download
1
Transcript of Rtd
![Page 1: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/1.jpg)
Ch E 441 - Chemical Kinetics and Reaction Engineering
Residence Time Distributionsin Chemical Reactors
![Page 2: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/2.jpg)
Residence Time Distributions• The assumption of a “perfectly mixed” reactor
often falls short of reality.• Residence time distributions are used to model
the imperfect mixing behavior of real reactors.– Cumulative age, F(t)– External age, E(t)– Internal age, I(t)
![Page 3: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/3.jpg)
Residence Time Distributions• Gas-liquid CSTR (A(g) + B(l) C(l))
– Reaction occurs at gas-liquid interface– Liquid phase is perfectly mixed– Rate is proportional to bubble surface area– Residence time of gas bubble in reactor is
proportional to bubble volume• Larger bubble escape rapidly• Smaller bubbles may remain in reactor until consumed
– Understanding of RTDs is necessary for analysis
![Page 4: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/4.jpg)
Residence Time Distributions• PBR
– Sections of the catalyst bed may offer less resistance to flow, resulting in a preferred pathway through the bed.
– Molecules flowing through the “channel” do not spend as much time in the PBR as those taking another path.
– Consequently, there is a distribution of residence time for the PBR.
![Page 5: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/5.jpg)
Residence Time Distributions• CSTR
– Short-circuiting may occur (the direct movement of material from inlet to outlet.
– Dead zones may exist (regions with a minimum of mixing and thus virtually no reaction takes place).
![Page 6: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/6.jpg)
Residence Time Distributions• Concepts that must be addressed in approaching
a solution to such problems:– distribution of residence times occurs– quality of mixing varies with position in reactor– a model must used to describe the phenomenon
• Accounting for nonideality requires– knowledge of macromixing (RTD)– application of the RTD to a reactor (micromixing) to
predict reactor performance.
![Page 7: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/7.jpg)
RTD Functions• In any reactor, the RTD can affect performance
– Ideal Plug Flow and Batch Reactors• Every atom leaving reactor is assumed to have resided in
the reactor for exactly the same duration. No axial mixing.– Ideal CSTR
• Some atoms leave almost immediately, others remain almost forever. Many leave after spending a period of time near the mean residence time. Perfect mixing.
• RTD is characteristic of mixing in a reactor.• RTDs are not unique to reactor type.
Different reactor types can have the same RTD.
![Page 8: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/8.jpg)
Measurement of RTD• RTD is measured experimentally by use of an
inert tracer injected into the reactor at t = 0. Tracer concentration is measured at effluent as a function of time.
• Tracer must be non-reactive and non-absorbing on reactor walls/internals.
• Tracer is typically colored or radioactive to allow detection and quantification.
• Common methods of injection are pulse and step inputs.
![Page 9: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/9.jpg)
Pulse Input RTD Measurement• An amount of tracer No is suddenly (all at once)
injected into the feed of a reactor vessel with flow at a steady state.
• Outlet concentration is measured as a function of time.
reactor
injection detection
feed effluent
![Page 10: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/10.jpg)
Pulse Input RTD Measurement
reactor
injection detection
feed effluent
pulse injection
C
t0 +-
pulse response
C
t0 +-
![Page 11: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/11.jpg)
Pulse Input RTD Measurement• Injection pulse in system of single-input and
single-output, where only flow (no dispersion) carries tracer material across system boundaries.
• The amount of tracer materialN leaving the reactor between t and t+t for a volumetric flowrate of is
where t is sufficiently small that the concentration of tracer C(t) is essentially constant over the time interval.
ttCN
![Page 12: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/12.jpg)
Pulse Input RTD Measurement• Dividing by total amount of tracer injected, No
yields the fraction of material that has a residence time between t and t+t:
• where E(t) represents the residence-time distribution function.
ttEtN
tC
N
N
oo
0 dttC
tCtE
![Page 13: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/13.jpg)
Step Input RTD Measurementstep injection
C
t
step response
C
t
reactor
injection detection
feed effluent
![Page 14: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/14.jpg)
Step Input RTD Measurement• In general, the output concentration from a
vessel is related to the input function by the convolution integral (Levenspiel):
where the inlet concentration takes the form of either a perfect pulse input (Dirac delta function), imperfect pulse injection, or a step input.
dt'tE 'ttCtCt
0inout
![Page 15: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/15.jpg)
Step Input RTD Measurement
t
0o
t
0inout dt'tE Cdt'tE 'ttCtC
• Considering a step input in tracer concentration for a system of constant :
0tC
0t0tC
oo
constant can be broughtoutside the integral
![Page 16: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/16.jpg)
• Divide by Co
– F(t) fraction of molecules that have spent a time t or less in reactor (Cumulative age)
• Differentiate to obtain RTD function E(t)
Step Input RTD Measurement
tF'dt'tE C
C t
0stepo
out
stepo
out
C
C
dt
dtE
![Page 17: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/17.jpg)
Step Input RTD Measurement• Advantages
– Easier to carry out experimentally than pulse test– Total amount tracer in feed need not be known
• Disadvantages– Often difficult to maintain a constant tracer
concentration in feed.– differentiation of data, often leads to large error.– Requires large amount of tracer, which in some cases
can be expensive.
![Page 18: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/18.jpg)
RTD Characteristics• E(t) is sometimes called the exit-age distribution
function. • If the age of an atom is regarded as the amount
of time it spends in the reactor, E(t) is the age distribution of the effluent.
• E(t) is the most often used distribution function for reactor analysis.
![Page 19: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/19.jpg)
• Fraction of exit stream that has resided in the reactor for a period of time shorter than a given value of t:
• Fraction of exit stream that has resided in the reactor for a period of time longer than a given value of t:
Integral Relationships
tFdttE t
0
tF1dttE t
![Page 20: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/20.jpg)
Integral Relationships
![Page 21: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/21.jpg)
Mean Residence Time
0
0
0m dttE t
dttE
dttE tt
• The nominal holding time, , is equal to the mean residence time, tm.
• The mean value of the time is the first moment of the RTD function, E(t).
• can be used to determine reactor volume
![Page 22: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/22.jpg)
• 1st moment – mean residence time
• 2nd moment – variance (extent of spread of the RTD)
• 3rd moment – skewness (extent RTD is skewed relative to the mean)
Other Moments of the RTD
0
2m
2 dttEt-t
0
3m
13 dttEt-t s 23
![Page 23: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/23.jpg)
Normalized RTD Function, E()
t
• A normalized RTD is often used to allow comparison of flow profiles inside reactors of different sizes, where
tEE
etEE
e1
tE tfor an ideal CSTR
![Page 24: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/24.jpg)
Internal-Age Distribution, I()• Fraction of material inside the reactor that has
been inside for a period of time between and +
0dE1
1I
![Page 25: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/25.jpg)
RTD in a Batch or PFR• Simplest case• Spike at t = (or = 1) of infinite height and zero
width with an area of one
ttE
0x
0x0x
1dxx
gdxxxg
![Page 26: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/26.jpg)
• Effluent concentration is identical to that of reactor contents.
• A material balance for t > 0 on inert tracer injected as a pulse at t = 0
RTD in a CSTR
dt
dCVC0
acc out -in
t0eCtC
![Page 27: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/27.jpg)
RTD in a CSTR• Recall definition of E(t), and substitute:
dt
dCVC0
acc out -in
t0eCtC
t
0
t0
t0
0
e
dteC
eC
dttC
tCtE
![Page 28: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/28.jpg)
Ideal Reactor Response to Pulse
E
t
Batch/PFR
E
CSTR
1
1
![Page 29: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/29.jpg)
Laminar Flow RTD
2
2o
2
max R
r1
R
2
R
r1UU
• Velocity profile in a pipe (cylindrical coordinates) is parabolic according to:
• Time for passage of an element of fluid is
22o
2
Rr1
1
2Rr1
1
2
LR
rU
Lrt
![Page 30: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/30.jpg)
• The fraction of total fluid passing between r and r+dr is d/0:
Laminar Flow RTD
00
rdr2rUd
rdr
R
t4rdr
Rr1
2
R
4dt 2
22
22
2Rr1
1
2rt
![Page 31: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/31.jpg)
Laminar Flow RTD• Combining
dtt2
dtt4
R2
t
Lrdr2
t
Ld3
2
2
2
000
00
rdr2rUd
rdr
R
t4rdr
Rr1
2
R
4dt 2
22
22
![Page 32: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/32.jpg)
Laminar Flow RTD• The minimum time the fluid will spend in the
reactor is
• Therefore, the complete RTD function is
22
V
R
R
U2
L
U
Lt
02
2
avgmax
23
22
tt2
t0tE
5.0
2
15.00
E3
![Page 33: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/33.jpg)
Laminar Flow RTD• The RTD appears graphically as
5.0
2
15.00
E3E
1
0.5
![Page 34: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/34.jpg)
RTD of PFR and CSTR in series• CSTR (s) followed by PFR (p)
– CSTR output will be delayed by a time of p
ps
tp
te
t0
tE sp
![Page 35: Rtd](https://reader031.fdocuments.in/reader031/viewer/2022013101/55657075d8b42a95028b467c/html5/thumbnails/35.jpg)
RTD of PFR and CSTR in series• PFR (p) followed by CSTR (s)
– PFR output will delayed the introduction of the pulse to the CSTR by a time of p
Regardless of the order, the RTD is the same. However, the RTD is not a complete description of structure for a particular reactor or system of reactors (see Example 13-4).
ps
tp
te
t0
tE sp