RT-9600User's Manual V1.3e

8/10/2019 RT-9600User's Manual V1.3e

1/49

RT-9600

Semi-auto Chemistry Analyzer

Users Manual


2/49

RT9100 Semi-Automatic Biochemistry Analyzer Consumer Operating Instruction Manual

Copyright: Rayto Lie an! Analyti"al S"ien"es Co#$Lt!#

A!!ress: C%&'()$ *th+inghua ,n!ustrial l!g$ .anhai R!$ .anshan$

Shenzhen /106*$ 2#R# China

3C Representation: Shanghai ,nternational 4ol!ing Corp#5m473urope8

A!!ress: 3iestrasse 10$ &-0/*$ 4amurg$ 5ermanyTel: 00(9-(0-/*/ )a;: 00(9-(0-//*6

Re


3/49

RT-9600 Users Manual

4o= to use this manual

,ts greatly appre"iate! you e"ome the user o RT-9600 Semi-auto Chemistry

Analyzer#

In order to get the best effect, you must be familiar with our instruments and their functionsbefore erforming the clinical diagnostic tests!

This manual is the oerating guidance of RT-9600 "emi-auto #hemistry $naly%er of Rayto

#omany, which including the contents of instrument installation, daily test, &uality control,

and daily maintenance, etc! $s to the users who uses e'ternal rinter, lease refer to the

users manual of e'ternal rinter at the same time!

(lease reser)e all the ac*ing materials for the use of deosit, transortation and

maintenance in the future!

+ou may contact with your distributor if there is any roblem!

As to the instruments o !ierent arning: >arning in!i"ations must e oeye!$ so as to ensure>arning: >arning in!i"ations must e oeye!$ so as to ensure

the normal operation o instruments an! "orre"t an!the normal operation o instruments an! "orre"t an!

real test results# ol!-a"e is use! to ma?e thereal test results# ol!-a"e is use! to ma?e the

!ieren"e#!ieren"e#

!


4/49


5/49


The symbol indicates temerature range of the analy%ers during

storage and transortation!

#


6/49


>arning an! Saety ,n!i"ations

This instrument is only used for in )itro diagnosis, lease carefully read the following

warnings before the usage, and strictly obeys them!

>arning: 2lease "areully rea! the ollo=ing announ"ements eore using

this instrument#

Cut o the po=er sour"e at on"e i there is anormal smells or smo?es$

an! pull out the po=er plug rom the outlet# At the moment$ you must

imme!iately propose test appli"ations to the !istriutors an! the

agents o our "ompany# , it is "ontinuously use! un!er this "on!ition$

it may "ause ire$ ele"tri" sho"? or personnel "asualty#

.either loo! an! reagent nor metal pie"es o staple an! pin shoul! e

!roppe! into the instrument@ other=ise it =oul! lea! to short "ir"uit or

smo?e an! ire# , there is something anormal$ "ut o the po=er

sour"e at on"e$ an! pull out the po=er plug rom the outlet# At the

moment$ you must imme!iately propose test appli"ations to the

!istriutors an! the agents o our "ompany#

perators !ont tou"h the ele"tri" "ir"uit insi!e the instrument$

espe"ially =et han!s$ =hi"h may e easier to get ele"tri" sho"?#

Ruer glo


7/49


e sure not to insert the plug into the ele"tri"al outlet o alternating

"urrent o


8/49


Content

8ow to use this manual!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

"ymbols on the instrument!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!:

;arning and "afety Indications!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! "elect roer osition!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!=0

=!>!:! (ower source re&uirement!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!=0

=!>!!>! #onnect e'ternal rinter!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!==

=!>!6! Install @low-#ell!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!==

=!6! Main structure!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!=

=!6!=! @ront )iew!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!=

=!6!! Aeyboard and mouse!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!=:

=!6!:! 4ac* )iew!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!=:

=!6!

=!6!>! @low-#ell!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!=,:0,:B

@low-#ell @low-#ell

Interface R"-: bidirectional communication and U"4 interface,

etc!

.islay 3i&uid crystal dislay

(rint Internal rinter or e'ternal rinter

;or* en)ironment 0-H

"torage en)ironment -=0-H

;eight =0*g

?)erall dimensions :B0mmC3D708%608%

(ower inut 70J$

@use attern L>0

@use rated )alue :!=>$3>0J

#/# ,nstrument installation

## ,nstrument pening an! Sealing

=! Unac* the instrument ac*age, and remo)e the materials used in the

transortation! (lease reser)e the ac*ing bo' and materials well, and its

con)enient for you to reac* the instrument someday in the future!

! Ta*e the instrument out of the lastic ac*age!

:! $ccording to the ac*ing list, confirm the following stuffs should be included in the

ac*age

RT-9600 "emi-auto #hemistry $naly%er

Users manual

(ac*ing list

11


12/49


;arranty certificate

(ower line

E# certificate

Note: The product accessories should be in accordance with the packing

list. Please contact with the distributor when the accessories

are found not right.

## Sele"t proper position

In order to ensure the normal wor* of instrument, lease select the wor*ing laces that

meet the following re&uirements to ut RT-9600 Semi-auto Chemistry Analyzer:

;or*ing table without direct sunshineF

The surface of wor*ing table is flat, sace is enough, and there is no big sha*e

Ce!g! hydro e'tractorDF

o electromagnetic de)ice that roduces magnetic field aroundF

(laces without e'treme changes of temeratureF

(laces without lots of dust!

Attention: The work environment of instrument is that temperature is

between 0 !0 and relative humidit" is below #$%.

## 2o=er sour"e reBuirement

a!c!==0J0JK==JJ,

>08%608%

70J$

#(# Conne"t instrument to po=er sour"e

Insert the two ends of ower line in the instrument outlet and alternating current

outlet resecti)ely!

>arning : Alternating "urrent po=er must e =ell earthe!#

Alternating "urrent po=er must e stale# ,t is prohiite! to use

po=er sour"e =ith high-po=er eBuipments together$ an! its

etter to eBuip =ith


13/49


, there is smo?e$ anormal smell or strange soun! o

instrument$ "ut o the po=er at on"e$ an! "onta"t =ith the

!istriutor#

>hen po=er line is inserte! or pulle! out$ you must hol! plug

itsel$ not the po=er line#

#/# Conne"t e;ternal printer

=D 2nsure both the rinter and instrument is ower off!

D Insert one end of U"4 connecting cable into the U"4 interface soc*et of

rinter!

:D Insert the other end of U"4 connecting cable into the U"4 ort of

instrument!


14/49


=D ust as the abo)e figure, ush away the uer co)er of the instrument after unscrewing

the hand-rotating screw fi'ing the uer co)er!

D Ta*e off the adhesi)e tae used to fi' @low-#ell, and ta*e off the wraing materialsF

:D (ut @low-#ell in the thermostatic bath, ay attention to ma*e the light hole direction thesame with that of the light ath!

D Install the uer co)er again, and rotate the screw tightly!

>arning: &ont tou"h the light hole o )lo=-Cell$ so as to a


15/49


N Indicating lam = "tate indicating lam!

N Indicating lam "tate indicating lam!

N (aer feeding button Internal rinter mo)es aer outward!

N Rinse *ey "tart or sto the rinsing of instrument channels!N $siration tube ;hen the instrument wor* is in @low-#ell mode, ress asiration *ey, and

the samle is asirated through asiration tube to the @low-#ell!

N $siration *ey (ress asiration *ey when the figure indicates asiration, the instrument

will automatically asirate the samle into @low-#ell!

N Instrument labeling

N 3#. screen .islay the interfaces!

N (rinter co)er The installation osition of rinting aer in internal rinter!

## Deyoar! an! mouse

RT-9600 can connect U"4 mouse and U"4 Aeyboard!

## a"?


16/49


N 2thernet interface

3 $d/usting screw of screen brightness

4 U"4 interface

5 ". card soc*et

N #?M interfaceN (ower switch

N (eristaltic um

#(# ,nternal printer

RT-9600 Semi-auto Chemistry Analyzer can be e&uied with rofessional internal

temerature sensiti)e rinter!

;hen internal rinter is used, select 1Internal rinter5 in the 1"ystem "etting5-1Mode5!

#/# )lo=-Cell

?en theuer co)er, the internal art of colorimetric system includes

Thermostatic bath

@low-#ell brac*et

@low-#ell

1$


17/49


@igure =-< #olorimetric system

@igure =-> @low-#ell

#6# Sour"e light an! peristalti" pump

Light sour"e mo!ule

?en the uer co)er of instrument, light source module is at the bac* of grating system,

and comosed of light source lam, brac*et of light source, light source soc*et and lens!

1%


18/49


@igure =-6 3ight source module

2eristalti" pump system

(eristaltic um system consists eristaltic um generator, eristaltic um installation

board, eristaltic um and um tube! (eristaltic um is installed on the outside of the

board behind the instrument, and its easy to change the eristaltic um tube!

@igure =-B (eristaltic um system

1&


19/49


#*# 2rin"iple stru"ture igure 7nly or reeren"e8

@igure =-7 (rincile structure figure

19


20/49


peration

## 2o=er on

?en RT-9600 ower switch, indicating light is on, and the system begins to load!

The icture is as following

@igure -= system loading

$fter finishing loading and system initiali%ation, enter main menu, as figure -

@igure - main menu

The administration software of RT-9600 Semi-auto Chemistry Analyzer has fi)e

function modules of test setting, test, result searching, system setting and user identify!

The function of all the modules and the oerati)e methods refer to the following

sections!

Note: In order to ensure the normal startup of instrument, please don&t

switch the power on immediatel" after turning off the power suppl".

The interval between power on and off should be more than '0

seconds.

## Test setting

It includes 1Test setting5 and 1on-chemistry "etting5! ?nly administrator can edit item

0


21/49


arameters! CRefer to section !6, User identifyD!

### 3!it io"hemi"al item

The test arameters of each item of RT-9600 can be edited by users!

"elect 1Test "etting5 in the main menu, system will enter item selection window, as

figure -:

@igure -: Item selection window

$fter selecting the item to be edited, clic* 1?A5 button to enter arameter setting menu,

as figure -


22/49


@igure -> #hange test mode

Temerature "elect > , :0 , :B and ambient temerature to testF

;a)elength Inut the needed wa)elength within ::0-700nmF

.ual wa)elength test is only alicable to endoint method item! If secondary

wa)elength is not needed to set, lease inut 19995 in the wa)elength columnF

Reagent blan* It can be selectedF

4lan* tye It is only for endoint method item! "amle blan*, reagent blan* or

none can be selectedF

@actor It is able to be get by calibration test or inut according to the reagent

instructionsF

"amle )ol!, reagent )ol! and asirate )ol! The unit is u3, and the recommended

asirate )ol! is >00mlF

.elay time It needs a eriod of time for the samle to be stable after being

asirated into @low-#ell, and then begin to read! The unit is secondF

Read time Test time articiated in the calculation! The unit is secondF CReading

time of endoint method is fi'ed to be = second, and no setu is needed!D

(ress 1Result5 button in the arameter setting window, erform setu to the relatedarameters of test results! $s figure -6

@igure -6 Result arameters setting

Unit There are =0 fi'ing units to select! In addition, > units can be defined by users

in the system setting menu Crefer to section !>!=DF

.ecimal The number of digitals that the result reser)ing behind decimalsF

3inearity error ?nly for item setting of Ainetics methodF

3inearity limit "et the linear uer limit of item test resultsF

Reference range "et the normal range of item test resultsF

There are fi)e functional buttons under the arameter setting window, they are

1"tandard5, 1#ontrol5, 1"a)e5, 1(rint5 and 1Result5! If the item needs to set the arameter of calibration standard, clic* 1"tandard5


23/49


button, erform setu to the corresonding arameter in standard arameter

setting window C@igure -BDF

@igure -B "tandard arameter setting

o! of std! Inut the number of calibration standard! ;hen non-linear fitting

calculation method is used, the number of standard rearations should be :

at least! ?nly one standard number of two oints method is ermitted!

Reeat times $s to each standard rearation, all of them can erform

multile measurement of district mean while doing calibration test, and the

reeating time is allowed to be = to :!

#alculation method ;hen samle concentration and absorbance meet the

linear relation, straight line fitting should be selected! ?therwise, non-linearfitting is chosen, and a *ind of calculation method among oly line fitting, cubic

cur)e fitting, logarithmic fitting and inde'ing fitting should be selected!

"tandard concentration The inutting of standard rearation concentration

should meet the rogressi)e order from low to high!

If the item needs to set &uality control rearation arameters, clic* 1#ontrol5

button! The arameter of item &uality control rearation can be set in 1&uality

control setting5 window C@igure -7D, as well as select the rules of losing controlF

@igure -7 Euality control arameters setting

!


24/49


25/49


@igure -=0 on-chemistry test selecting window

$s to the => items in the list, users can select any item of them according to the

re&uirement, clic* 12dit5 button to enter editing window and inut the item name, item

result &uality C&ualitati)e or &uantitati)eD, result, reference )alue and unit C&ualitati)e

items ha)e no unitD! $s figure -==

@igure -== on-chemistry test setting window

## ,tem test

$fter finishing the arameter setu of item test, users can erform item test at once!

"elect 1Test5 in the main menu, system will enter item selection window! $fter selecting

the item to be tested in the list, clic* 1?A5 button to enter the test menu!

The current colorimetric mode C@low-#ell or #u)ette modeD is indicated on the right

uer corner of the test menu, and it can be re)ised during the system setu!

If @low-#ell test mode is selected, lease reare the samle to be tested

according to the indication column, and ress asiration *ey to asirate samlesF

If #u)ette mode is alied, lease lace the #u)ette according to the indication

column, and then ress asiration *ey to start readingF

Under the mode of #u)ette, asiration *ey only controls the start of reading, not thestart of eristaltic um!

#


26/49


### Asoran"e test

"elect 1$4"5 in the test item list, system will enter the absorbance test menu! $s figure

-=

@igure -= $bsorbance test

It can erform water blan*, reagent blan*, samle blan* and samle absorbance

testF

The number of tested samle is added automatically, and the samle number can

be changed by user according to the re&uirements at any timeF

#lic* 1(rint5 button, it can rint test result and cur)e chartsF

#lic* 14ac*5 button, the system will indicate the following information Cfigure -=:D,

and then turn bac* to the re)ious menu!

@igure -=: Rinsing indication

### 3n!point metho! test

Test rincile $fter mi'ing the reagent and samle, reaction reaches the endoint after

some time i!e! color or absorbance of reaction solution do not change any

longer at this time measure the absorbance )alue of reaction

solutionconcentration of reaction solution can be obtained according to 3ambert-4eer

$


27/49


3aw! RT-9600 ro)ides .ual wa)elength test method to some of test items in this

way some interference factor can be erased! Users can erform .ual wa)elength

setu according to the re&uirements of reagent instructions!

"elect an endoint method item from the test item list, clic* 1?A5 button, system will

enter the menu of endoint method test! $s figure -=


28/49


@igure -=> "tandard selection window

"elect the standard rearation to be tested Caccording to the standard arameter

setting, 7 standard rearations can be chosen at the mostD, clic* 1?A5F

"tandard test information aears in the indication column of the test menu, as figure -

=6, erform test oeration according to the indicationsF

@igure -=6 "tandard test

@inish calibration test, and the system will dislay new calibration result, as figure

@igure -=B ew calibration result

&


29/49


If the calibration test results of this time need to be sa)ed, clic* 1"a)e5 button, system

will automatically renew the calibration data of this item! ?therwise, clic* 1Oi)e u5

button, system will continue to use the old calibration data!

Note: )orrect calibration result is the important premise of the accurate

result of sample test. (n the precondition of not changing reagent

and no changes of machine environment, calibration test is not

necessar" to be performed ever"da".

Euality "ontrol test

Euality control test can erform effecti)e monitoring to the current accuracy of the

system! ;hen the results of &uality control test are abnormal, users ha)e to chec*

the current condition of system! Euality control test can be erformed at any time!

In the test menu, clic* 1#ontrol5 button, &uality control selection window will aear,

as figure -=7

@igure -=7 Euality control selection

"elect the &uality control rearations to be tested Caccording to the &uality control

arameter setting, : &uality control rearations can be chosen at the mostD, clic*

1?A5F

Euality control test information aears in the indication column of test menu

Cfigure -=9D, erform test oeration according to the indicationsF

9


30/49


31/49


enter the mode of Ainetics method test, as figure

@igure -= Ainetics method test

This item can test water blan*, reagent blan* and samle testF

.uring the test rocedure, &uality control test can be inserted! Ainetics test dose

not need calibration testF

The number of test samle will be added automatically, and the samle number

can be changed by user at any timeF

$ny data inter)al can be selected to calculate againF

The test results are not linear, when it e'ceeds linear error or linear test range,system can warn and indicateF

#lic* 1(rint5 button, test results and cur)e chart can be rintedF

#lic* 14ac*5 button, after indicating washing system, return to the uer menu!

Note:

*hen the test results of +inetics method occur nonlinear,

eceeding linear error range or eceeding linear test range, s"stem

can warn and indicate. At the moment, users can appl"

corresponding treatments according to the re-uirements.

*hen +inetics method appears nonlinear test results, users can

calculate again according to the fied data intervals of reaction

curve.

#(# Test result sear"hing

#(## Stan!ar! sear"hing

"elect 1#alibration5 in the main menu, system enters item selection window! "elect the

needed items from the list, clic* 1?A5 button, and system enters 1#alibration5 menu, as

!1


32/49


figure -

@igure - #hec* calibration data

@igure -: #hec* calibration cur)e

@igure - and figure -: are the calibration data and cur)e of item T( resecti)ely!

#lic* 1(rint5 button, calibration data and cur)e can be rinted!

#(## Euality "ontrol sear"h

"elect 1E# result5 in the main menu, system enters item selection window! "elect the

needed items from the list, clic* 1?A5 button, and system enters 1E# Result5 icture, as

figure -


33/49


@igure -< .ata chec*u of &uality control

"elect &uality control rearation and months in the window dislayed in the figure abo)e,

corresonding &uality control data will be dislayed in the list! #lic* 1#ur)e5 to chec* the

&uality control chart, as figure

@igure -> Euality control chart

@igure -: is the test results of &uality control of item $34 in "etember!

#lic* 1(rint5 button to erform the rint of &uality control results!

#lic* 1#lear5 button to clear the aointed results of &uality control!

#(## Report print

"elect 1reort rint5 in the main menu, system will enter the following window

!!


34/49


35/49


test results in the system!

"elect one or more atients clic* 1(rint5 button, system will rint the test reort of

corresonding atient! Cif all the records in the list need to be chosen, lease

select 1select all5 , otherwise, lease dont selectD

2atient inormation e!iting

#lic* 12dit5 button in the window of figure -B, enter atient information edit window, as

figure -7

@igure -7 (atient information edit window

Inut samle number and other atient information, and then clic* 1"a)e5! If the record

of this atient is e'isted, renew the atient records, or add a new atient recordF

Note:

ifferent patients must be marked b" different sample number in

the same date.

In order to ensure the check efficienc" of software, please clear the

old patient records in time.

Re


36/49


@igure -9 (atient test item 2diting

If the test results need to be re)ised, select the test records first! Inut the results in

the corresonding comiling frame below the list, and then clic* 1Re)ise5F

If need to add non-chemical item test results to e'ited atient record, clic* 1$dd5

button to enter the menu as the following figureF

@igure -:0 $dd non-biochemical items

"elect non-chemical items in the ull-down list, inut the corresonding results, and

then clic* 1"a)e5 to add a non-chemical item record to the current atient!

Note: (nl" administrator can revise the test result, common users can not

revise/

2rint y items

!$


37/49


@igure -:= Item reort window

In 14y item5 window, select the date, and select the items to be rinted, clic* 1(rint5 *ey!

(rint the result reorts of the selected items in the aointed date!

2rint history re"or!s

@igure -: 8istory record window

"elect the date in 18istory record5 window, and all the history records of the

corresonding date will be dislayed in the list!

"elect one or more records in the list, and then clic* 1.elete5 or 1(rint5!

"electing 1"elect all5 means to select all the records in the list!

#lic* 1#lear all5 to delete all the history records in the system!

Note: In order to ensure the check efficienc" of software, please clear the

old histor" records in time.

2rint or!er

!%


38/49


In the 1(rinter order5 window as figure -::, select any item, and then clic* 1U5 or

1.own5 *eys to change the rinting order of items in the reort! #lic* 1Initial5 *ey, the

rint order will return to the default setting, i!e! arrange by letter order!

@igure -:: (rint order

#/# System setup

#/## System parameter setup

"elect 1"ystem "etting5 in the main menu, system will enter system setu window! $s

figure -:


39/49


@igure -:> "ystem setting -

@igure -:6 "ystem setting -:

"ystem setu includes the following setu items

" " is the serial number of machine, this information setu is not oened to the

users!

8osital name Inut the name of the hosital using the instrument, this information will

be rinted in the reort title as hosital name!

.ate and time .islay the current time of system, users can re)ise and correct it!

User-defined unit RT-9600 allows users to define > units according to the re&uirements,

besides =0 fi'ing units! Re)ise the user-defined units, the unit selections, during

biochemical item arameters editing, will change too!

#olorimetric mode ;hen cu)ette is needed to erform test, lease select 1#u)ette5,

otherwise, select 1@low-#ell5 mode!

(rinter RT-9600 ro)ides internal rint and e'ternal rint modes! ;hen internal rint

mode is selected, users ha)e to aoint whether instant rint is needed! ;hen e'ternalrint mode is chosen, the rinter tye needs to be selected!

!9


40/49


"ystem temerature The left lower corner of the menu dislays the real time

temerature of the system!

Touch anel (erform calibration of touch anel Cotional functionD!

#/## System maintenan"e

In system setu menu, clic* 1Maintenance5 button to enter system maintenance

window, as figure -:B

@igure -:B "ystem maintenance-=

Temerature set the system temerature, ambient temerature, > , :0 or :B

can be selected!

#urrent temerature .islay the current temerature on real time of the system!

Temerature factor If the real temerature of system is not in accordance with target

temerature, users can erform ad/ustment!

$d/ustment method If the real temerature is lower than the target temerature,

increase the amount ad/ustment of temerature! ?n the contrary, reduce the amount of

ad/ustment of temerature! The inutting range of temerature ad/ustment is from

-!0 to !0 !

(um seed Regulate the rotation seed of eristaltic um while asirate fluid! There

are = to 7 *inds of methods from slow to &uic*! The default )alue is 6! 2mty )olume Regulate the time of system emtying after each samle test! The

bigger the emty amount is, the longer the time is! The default )alue is 700!

(um factor ;hen the asirate )olume of system has de)iation, the de)iation can be

eliminated by re)ising the calibration factors of eristaltic um

#alibration method ;hen the asirate )olume is smaller than e'ected, increase the

calibration factors of eristaltic um! ?n the contrary, reduce it!

"0


41/49


@igure -:7 "ystem maintenance-

Tyical =0 wa)elengths "elect this item, the system will scan the =0 default

wa)elengths C:B7, 60 and 6B0nmD

User-defined "can according to the aointed scanning wa)e band and scanning

inter)als!

4lan* scan #lic* 1scan5 button after selecting the scanning mode, the system will

erform scan to the water blan* )alue of each wa)elength automatically, and the

scanning results are to be dislayed in the list! #lic* 1rint5 button, and users can rint

the scanning results!

Note: efore the blank scanning, please ensure the 1low)ell or )uvette is

full of distilled water or other things to be tested.

@igure -:9 "ystem maintenance-:

"1


42/49


#hanging date of um tube Record the date of changing um tubes at the last time,

system will /udge whether it is needed to indicate users to relace a new one according

to this! The eriod of changing um tube is : months, and the system will indicate

while it is e'ired! #hanging date of lam Record the date of changing lams at the last time, system will

/udge whether it is needed to indicate users to relace a new one according to this! The

eriod of changing lams is 6 months, and the system will indicate while it is e'ired!

Note: 2"stem setup window is onl" open to the administration user.

After changing the pump tubes or lamps, please renew the changing

date, so as to ensure the indication of s"stem is correct.

#6# User i!entiy

"elect 1User identify5 in the main menu, system will enter identity setu window, as

figure -


43/49


results, it is suggested to *ee the assword of administrator secret!

In user identify window, users can select the login identity Cadministrator or common

user identityD! $t the same time, the assword of administrator can be re)ised! 4oth

selecting administrator identity and re)ising administrator assword need to inut theassword of administrator!

#*# Aout

#lic* 1Rayto5 icon in the main menu, the icture of system )ersion information occurs,

as figure -


44/49


asiration *ey! Turn off the ower suly after finishing washing according to the

indications!

# Maintenan"e

##


45/49


>arning: &ont leaarning: Must use the use o the spe"ii"ations aohen use is"hange!$ ori! to operate =ith ele"tri"ityG

### A!ustment o peristalti" pump tue

$fter the instrument is used for a long time, the osition of eristaltic um can be ad/usted!

The methods are

Rotate the loc* catch of eristaltic um tube cloc*wise, and oen the bac*late of

um tube!

Ta*e off the eristaltic um tube!

3oose the fi'ing steel wire on the connecter of um tube, rotate the um tube for

=70Q, and then refi' the steel wires!

Install the um tube well, and loc* Crotate the loc* catch of eristaltic um

countercloc*wiseD!

>arning: If the pump tube is not installed well, the instrument will not

aspirate.

### Change aspiration tue

If asiration tube Cor flow @low-#ellD is bloc*ed by miscellaneous ob/ects, syringe can be

used to clean and dredge! If the damage or bloc* of asiration tube is serious, you can

change an asiration tube! The methods are

(ull flow @low-#ell out!

Remo)e the asiration tube at the entrance, and change a new asiration

tube! $t one end of the new asiration tube, comass tube Cthe middleD is

sheathed first, and then fi'ing tube Cthe thic*estD is sheathed! (ay attention to

"#


46/49


lea)e =cm outside the comass tube! C$s figure :-=D!

@i' the fi'ing tube to the entrance of flow @low-#ell!

@igure :-= $siration tube connector at the entrance of flow @low-#ell

##(# Change o light sour"e lamp

(lease cut off the instrument ower suly before changing lam!

(ull out the connecting line of the light suort ower suly, and rotate out the screw =

and on the light source brac*et! Crefer to figure =-B 3ight source moduleD

Ta*e off the light source brac*et, change a new one, ut as the original way, and rotate

screw tightly!

#onnect the ower source connecting line of the light source unit well!

Ma*e the siral images in the middle of the seam of monochromator through lens by

slightly regulate the osition of light source with screw = and !

#(# Simple troule !isposal

Troule Shooting

=$naly%er can not be started! #hec* whether the instrument is switched on!

#hec* whether the ower lug is loosen!

#hec* the fuse!

#hec* the ower suly!

D The lam is not lighted! #hec* ower suly before changing bulbs!

If the lam is damaged, change lam!

:D (rinter can not be started! #hec* whether the ower lug is loosened!

#hec* ??@@ button of rinter!

#hec* the fuse of rinter!

D There is no fluid in the @low-#ell! #hec* whether eristaltic um is normally

running!

"$

$siration tubecomass tube

@i'ing tube


47/49


#hec* the connection of asiration tube and flow @low-#ell,

etc!

$siration tube is too long or too short!

$siration tube may be bloc*ed, and it should be cleared and

dredged!@low-#ell is )ery dirty!

6D There is no reading on the hotometer! #hec* whether the lam of hotometer is

lighted!

Try another wa)elength to read!

@low-#ell is not inserted to the bottom!

BD The .e)iation of water blan* is too big! #lean @low-#ell!

#hange new distilled water!

#hec* the lam of hotometer!

7D The result reroducibility is low! There are bubbles inside the @low-#ell, and it

should be washed!

#hec* the asiration condition of @low-#ell!

The amount of reagent is too little, and the )olume should be

increased!

#hange the lam of hotometer!

Reaction fluid is olluted!

The asiration tube has been inserted too dee into the @low-

#ell, ull it out slightly!9D The asiration )olume of @low-#ell not #hec* whether asiration tube is bloc*ed!

stable!

(eristaltic um tube should be changed!

=0D Euality control out of target )alue range! #hec* the )alid date of reagent!

#hec* whether the settings are correct, and whether it need

re)ise arameters!

Ma*e sure &uality control is not olluted!

Measure again with other methods!

#hec* the @low-#ell, use another reagent or &uality control to

test again!

"%


48/49


(# Appen!i;: &ata a"?up an! serial intera"e !ata transmission

.ata bac*u function can be used to erform data arameter e'ort and imort, and

the data also can be e'orted from serial interface!

#lic* 1data bac*u5 button in the main menu, enter data bac*u window, as figure


49/49

RT-9600User's Manual V1.3e

Documents

Transcript of RT-9600User's Manual V1.3e