ROSSO MOTORS ELECTRIC ATVOWNERS MANUAL

Read and understand this manual Prior to Riding!

DO NOT RETURN TO STORE!Illustrations may not be an exact representation of actual product.

Table of Contents

General information: ..............................................................................................................................................3

Assembly: .................................................................................................................................................................5

Components definition: .......................................................................................................................................11

Maintenance and adjustments ...........................................................................................................................14

Troubleshooting ...................................................................................................................................................16

Wiring diagram: ....................................................................................................................................................17

Warranty ................................................................................................................................................................18

2

3

General Information:

WARNING:

Riding an electric ATV can be a dangerous. Like other electric rideable products, electric ATV’s are intended to move, and it is therefore possible to lose control, fall off and/or get into dangerous situations that no amount of care, instruction or expertise can eliminate safety equipment and other precautions.

RIDE AT YOUR OWN RISK AND USE COMMON SENSE.

This manual contains many warnings and cautions concerning the consequences of failing to main-tain, inspect or properly use your electric ATV. Because any incident can result in serious injury or even death, we do not repeat the warning of possible serious injury or death in each section as it is mentioned here. APPROPRIATE RIDER USE AND PARENTAL SUPERVISION are strongly advised.

This manual contains important safety information. It is your responsibility to review this information and make sure that all riders understand all warnings, cautions, instructions and safety topics and assure that young riders are able to safely and responsibly use this product.Rosso Motors recommends that you periodically review and reinforce the information in this manual with younger riders, and that you inspect and maintain your children’s ATV to ensure their safety and enjoyment.

A parent’s decision to allow his or her child to ride this product should be based on the child’s maturity, skill and ability to follow rules.

Keep this product away from children under the recommended rider age 3 - 8 years old and remem-ber that this product is intended for use only by persons who are, at a minimum, completely comfort-able and competent while operating the product.

DO NOT EXCEED THE WEIGHT LIMIT OF 90 lbs.

Rider weight does not necessarily mean a person’s size is appropriate to fit or maintain control of this electric ATV. Do not touch the brakes or electric motor on your electric ATV when in use and/or imme-diately after riding as they can become very hot.

Always check and obey any local laws or regulations which may affect the locations where the ATV Quad may be used.

Ride defensively.

Watch out for potential obstacles that could catch your wheel or force you to swerve suddenly or lose control.

Be careful to avoid pedestrians, skaters, skateboards, scooters, bikes, children or animals who may enter your path, and respect the rights and property of others.

Your kids ATV is meant to be used on private property and on closed courses and not on public streets or sidewalks , unless approved by your local traffic laws. Do not ride your electric ATV in any areas where pedestrians or vehicle traffic is present.

Do not activate the speed control on the hand grip unless you are sitting properly on the electric ATV and in a safe, outdoor environment suitable for riding.

This product was manufactured for performance and durability but is not impervious to damage. Jumping or other aggressive riding can over-stress and damage the product and the rider assumes all risks associated with high-stress activity.

Be careful and know your limitations. Risk of injury increases as the degree of riding difficultyincreases, the rider assumes all risk associated with aggressive riding activities.

Maintain a hold on the handlebars at all times.

Never carry passengers or allow more than one person at a time to ride the electric ATV.

Never use near steps or swimming pools.

Keep your fingers and other body parts away from the drive chain, steering system, wheels and allother moving components.

Never use headphones or a cell phone when riding.

Never hitch on to another product.

Do not ride the Rosso Motors on wet or icy weather and never immerse the electric ATV in water, as the electrical and drive components could be damaged by water or create other possible unsafeconditions.

Wet, slick, bumpy, uneven or rough surfaces may increase risks of use. Do not ride your electric ATV in mud, ice, puddles or water. Avoid excessive speeds that can be associated with downhill rides. Never risk damaging surfaces such as carpet or flooring by use of an electric four wheeler indoors.

Do not ride at night or when visibility is limited.

PROPER RIDING GEAR

Always wear proper protective equipment such as an approved safety helmet, elbow pads andkneepads.

A helmet may be legally required by your local laws or regulation in your area.

A long-sleeved shirt, long pants and gloves are recommended.

Always wear athletic shoes (lace-up shoes with rubber soles), never ride barefooted or in sandals, and keep shoelaces tied and out of the way of the wheels, motor and drive system.

4

Assembly:

• Rosso Motor’s electric ATV requires minimum assembly. • Please follow instructions below in order to get your electric ATV assembled properly. • The Rosso Motor’s ATV comes in 2 boxes, one contains the ATV and hardware and the other one contains battery.

1.Hardware box contents:

2.Uncrate the ATV and remove it from the metal frame

5

Reflectors Handlebar mount hardware

Allen keys

Speed limit switch keys

Spare fuses

Screwdriver

WrenchesFront Bumper

Charger

Brake Caliper mounting bolts

6

3.Handlebar installation:

Failure to properly adjust and tighten the bolts can result in a loss of control of your ATV. Attach handlebar clamps and gear position indicator

4. Front wheels installation (repeat steps below for right and left wheels)

Remove self-locking nut and Insert front wheel into the axle and tighten the nut

5.Inflate tires

Inflate tires to the correct PSI before first time and check pressure before each ride.Recommended tire pressure is: 7 PSI (Maximum: 20 PSI)

Gear position indicatorHandlebar clamp bolts

Handlebar clamp

Front axle

Self lock nut Front

wheel

7

6.Front brake calipers installation (repeat steps below for right and left wheels)

Step 1: Insert brake caliper and make sure the disc brake is located in between the brake pads:

Step 2: Attach caliper to the mount using

brake caliper mounting bolts and tighten them

Step 3: Adjust caliper by tighten or untighten caliper

alignment bolts – make sure the caliper is aligned

with the disc brake.

Disc brake

Brake pads

8

7.Rear shock absorber installation

Step 1: Raise rear end of the ATV

Step 2: Install shock absorber into the bottom mount and tighten the bolt

8.Battery installation

Step 1: Open battery bag and pull out connector plug

Step 2: Remove battery security plate and place battery into the casing

Shock absorber

Connector plug

Casing

9

Step 3: Insert positive (RED) wire with fast connector that connected to the ATV into the connector plug. Insert the wire until you hear “CLICK”. The wire should be sitting inside the plug permanently.

Step 4: Connect positive (RED) wire with ring terminal to the battery and tighten the screw

Step 5: Connect plugs - insert the wire until you hear “CLICK”

Step 5: Close battery bag, secure security plate and tighten the bolts

Connector plugwire

CLICK

Ring terminal

10

9.Seat installationInsert front mount and push rear of the seat down until it locks

10.Install reflectors (RED reflectors at the back of the ATV and ORANGE at the front)

11.Install front bumper –make sure top and bottom mount bolts are tighten

Rear Left & Right

Front Left & Right

Rear Center

Front mount

Top mount bolt

11

Components definition:

Operation controls:

1. Gear shifter switch

2. Gear position indicator

When gear shifter is in N (neutral) position – N (green light) is on When gear shifter is in R (reverse) position – R (red light) is on When gear shifter is in F (forward) position – both N and R lights are off

Controller

Rear brake

Motor

Seat

Rear brake Front brake

lever

Head lights

12

3.Ignition/Power switch

4.Battery level indicator Located on the right side of the handle bar, MAX (green) – battery capacity is full MID (yellow) – battery capacity is half full MIN (red) – battery capacity is battery needs to be charged

5.Headlight switch Located on the left side of the handle bar I – lights are ON 0 – lights are OFF

13

6.Parking brake Located on the right side brake lever To engage: squeeze front brake lever and press the brake knob To disengage: squeeze brake lever until the know pops up

7.Fuse Located at the front left side of the ATV Fuse specs: 250V-30A

8.Speed switch Located at the left center side of the ATV The switch intended to limit the speed of the ATV. DO NOT leave keys inside the switch while ATV is running 1 – High speed 0 – Low speed 2 - Medium speed

14

Maintenance and adjustments MAKE SURE THE INGITION (MAIN SWITCH) IS OFF BEFORE PERFORMING ANY MAINTANANCE OR ADJUSTMENTS

1.Brakes adjustment Failure to inspect and properly adjust brakes increases the risk accidents. Riding with worn brake pads can reduce braking performance and cause an accident. Check and adjust brakes before each ride

To adjust cable play on the left (rear) brake lever – tight/untighten adjuster To adjust cable play on the right (front) brake lever - tight/untighten adjusters

Calipers adjustment (front & rear) Untighten (do not remove completely) anchor nut and pull brake cable (see directions) until the pads are almost touching the rotor (disc brake)

15

2.Charging

Charge batteries for at least 12 hours before initial use! Charger might get warm during charging process; this situation is normal and notconcerning. If the charger does not get warm, it does not mean that it is not workingproperly.

Step 1: Turn main switch OFF Step 2: Plug the charger into the charging port (located underneath the fuse) Step 3: Plug charger into a wall – if the light on the charger do not lights up, check power to the outlet.

3.Chain adjustment

Riding an ATV with chain in poor condition or improperly adjusted can lead to serious injury. Always inspect, maintain and adjust the chain properly before each ride. Before adjusting the chain, make sure the motor is cool. Do not touch motor after use. Motor is (or can be) very hot.

Step 1: Unscrew (do not remove completely) motor mount nuts (front & rear)

16

Step 2: Adjust (tight/untighten) chain adjuster bolts as necessary – make sure both bolts are adjusted equally

Step 3: Tighten mount nuts

17

Wiring diagram:

18

Warranty

ROSSO MOTORS warranties this product to be free of manufacturing defects for a period of 90 days from date of purchase. This Limited Warranty does not cover normal wear and tear, tires, tubes or cables, or any damage, failure or loss caused by improper assembly, maintenance, or storage or use MANTERAY

This Limited Warranty is voided if the product is:

• used in a manner other than for recreation;

• modified in any way;

• rented.

ROSSO MOTORS is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product. This is a use at your own risk product and Rosso Motor’s in to responsible for any injury that result from the use of our products.