Ronda 8040 N Complete Technical Documentation
description
Transcript of Ronda 8040 N Complete Technical Documentation
-
RONDA mastertech 8000
XXL Chronographs,
Retrograde and Big Date
Caliber 8040.N 15'''
Product Specifications
Analog quartz movement
Line mastertech
Caliber 8040.N
Size 15'''
Version Swiss Made 13 Jewels / gold plated
Standard battery life 48 months
Hand fitting height 1
Features
Repairable metal watch movement
Very long battery life
Power saving mechanism with pullled out stem: Reduction
of consumption approximately 70%
Very easy handling by two pushers
Big date with quick change
Date: 07.04.2015 www.ronda.ch Page: 1
-
RONDA mastertech Caliber 8040.N 15'''
Functions
3 eyes
Chronograph
Center stop second (1/1
sec)
1/10 seconds up to 30
minutes
30 minute counter
10 hour counter
ADD and SPLIT functions
Day Retrograde
Big date
Small second
Technical Specifications
Diameter Total 34.60 mm
Case fitting 33.80 mm
Movement height 5.60 mm
Height over standard battery 5.60 mm
Movement rest 0.60 mm
Height over stem 3.30 mm
Length of stem travel 1.00 mm
Stem thread 0.90 mm
Standard battery 395
Standard battery life 48 months
Battery voltage 1.5 V
Current consumption typical 1.48 A (Date
Mechanism not in
Gear)
Current consumption maximum 2 A (Date
Mechanism not in
Gear)
Useful torque second typical 6 Nm
Useful torque minute typical 300 Nm
Useful torque center stop second typical 7 Nm
Operating temperature 0 - 50 C
Instantaneous rate -10/ +20 sec/month
Resistance to magnetic fields 18.8 Oe
Resistance against shock NIHS 91-10
Date: 07.04.2015 www.ronda.ch Page: 2
-
Scurit entre l'aiguille des seconde et le verreSicherheit zwischen Sekundenzeiger und GlasSecurity between second hand and glass
: min 0.50 mm: min 0.50 mm
: min 0.50 mm
Poussoirs / Drcker / Pushers
courseWeg 1.30way
Position pousseGedrckte Stellung R 16.20 50Pushed in
+200-0
3.3
+
70 0
1.
4 20
0
1.8
10
6.5
14.14
1.41
16.22
13.06
Position zum entfernen der StellwellePosition to remove the stem
Position pour extraire la tige
PileBatterie 395 9.50 x 2.70Battery
S 0.
9Co
urs
e / W
eg
/ Tra
vel :
1.
00
S 0.
9
30
30
S 0.9
1
9.72
S 0
.9
6.68
14.85
5.6
2.8
min
5.
85
min
3.
05
3.3
+ 15
00
-
+ 70
0
0.00 - 0.15
0.00 - 0.22 34.6
+0 -30
1
.1
33.8 +0 -300.
6 10
Vis / Schraube / Screw No. : 4000.323 Vis / Schraube / Screw No. : 4000.324(R 16.28 3x)
0.43
2.1
0.3
0.8
1.2
3.95
(R 16.28 3x)
0.28
2.6
0.3
1.2
00No. 5000.3678040.N
Sous rserve de modificationsAenderungen vorbehalten
Modifications reserved
FrameUhrwerkgestellCage
RONDA
15'''
16 Mai 2008
Modified
Scale 10 : 1 (5 : 1) (A3H)+/- 20 m
mgIssued
ToleranceReleased
12 Feb 2010flA 5198
Yes
-
30
b
De
Dt
T
P
1
.4 200
Dp
Dp
30
b
Dp
0
a b
T
P
Dt
De
a
b
1.
6 0-10
0
D
p
0.
4
30 2
Dp
20
a b
T
P
Dt
De
a
b
0
.4
10 2
1
.6 0-100
Dp
20
Dp
15
a b
T
P
Dt
De
0.4
15 2
1
.6 0-100
Dp
a
b
15
Dp a b
10
T
Dt
De
P
1
.6 0-100
Dp
0
.4
20 2a
b
10
00No. 5000.3908xxx.x
Sous rserve de modificationsAenderungen vorbehalten
Modifications reserved
Angle of pusher A and BWinkel der Drcker A und BAngle des poussoirs A et B
RONDA
Modified
Scale 2.5 : 1 (10 : 1) (A3H)+/- 20 m
flIssued
ToleranceReleased
12 Feb 2010flA 5198
YES
22 Sep 2009
-
0.5 max.
0.250 0.900 +6 -4
1.500 +4 -2
0.7 0.5 max.
GE
F
Ajustement aiguille des heuresStundenzeigerpassungHour hand fitting
CylindriqueZylindrischCylindrical
Ajustement aiguille des minutesMinutenzeigerpassungMinute hand fitting
Petite secondeKleine SekundeSmall second
Aiguille des joursTageszeiger
Day hand
J
Compteur 1 aiguille1 Zeiger Zhler1 Hand counter
Ajustement aiguille des secondes chronoStopp-SekundenzeigerpassungChrono second hand fitting
Heures / minutes / secondes chronoStunden / Minuten / Stopp-Sekunden
Hours / minutes / chrono seconds
02No. 3316.1228040.N
Sous rserve de modificationsAenderungen vorbehalten
Modifications reserved
Hand fitting heightsZeigerwerkhhenAiguillages
RONDA
15 '''
02 Jun 2008
Modified
Scale 20 : 1 (A3H)m
mgIssued
ToleranceYesReleased
Masse / Masse / weight
A ig .
d e
s s e
c .
c hr o
no
S to
p p-
S ek u
nd e
nz e
i ge
r
C hr o
no
s e
c on
d h a
nd
A ig u
i l l e
c om
p te
ur
mi n
ut e
Z h l
er
Z ei g
er
Mi n
ut e
C ou
nt e
r h a
nd
mi n
ut e
Balourd / Unwucht / unbalance0.06
A ig .
p e
t i te
s e
c on
d es
K le
i ne
S e
k un
d en
z ei g
er
S ma
l l s e
c on
d h a
nd
A ig .
d e
s m
i nu
t es
Mi n
ut e
nz e
i ge
r
Mi n
ut e
h a
nd
A ig .
d e
s h e
ur e
s
S tu
nd e
nz e
i ge
r
Ho
ur
h an
d
Inertie / Massentrgheit / InertiaForce de chassage / Aufpresskraft / Force
0.80
40
30
0.80
10
0.07
10
0.03
40 30 30
gmm 2Nm
mg
N
--- ---
max.
max.
max.
max.
A ig .
d e
s j o u
r s
r t r o
g ra
d eT a
g es a
nz e
i ge
r r e
t r og r
ad
Da
y h a
nd
r et r o
g ra
d e Lors de la pose d'aiguilles, le mouvementdoit tre soutenu.Beim Zeigersetzen muss das Werkabgesttzt werden.The movement needs to be supportedfor hand setting.
A ig u
i l l e
c om
p te
ur
1 /1 0
s e
c .
Z h l
er
Z ei g
er
1 /1 0
S e
k .C o
un
t er
h an
d 1 /
1 0
s ec .
0.02
30
10
30
30 10 10
0.40
1.0
30
1.01.00.41.0
0.200
Ajustement aiguilleZeigerpassungHand fitting
Appui cadranZifferblattauflageDial seat
ConicitKonizittConicity2%
* En cas de donnes diffrentes, veuillez contacter le service aprs-vente * Bei abweichenden Werten, bitte technischen Kundendienst anfragen * In case of different values, please contact the customer service
S ou
s l ' a
i gu
i l le
d e
s j o u
r s
r t r o
g ra
d eU n
t er
T ag e
s ze
i ge
r r e
t r og r
ad
U nd e
r D
ay
h an
d r e
t r og r
ad e
S ou
s l ' a
i gu
i l le
d e
s s e
c on
d es
c hr o
no
U nt e
r
S to
p p-
S ek u
nd e
nz e
i ge
rU n
d er
c hr o
no
s e
c on
d h a
nd
S ou
s l ' a
i gu
i l le
d e
p e
t i te
s e
c on
d eU n
t er
k l
ei n
e
S ek u
nd e
nz e
i ge
rU n
d er
s ma
l l s e
c on
d h a
nd
S ou
s l ' a
i gu
i l le
c o
mp t
eu
r 1
ai g
ui l l
eU n
t er
Z e
i ge
r 1
Z ei g
er
Z h l
er
U nd e
r h a
nd
1 h a
nd
c ou
nt e
r
1.101.55
S ou
s l ' a
i gu
i l le
d e
s h e
ur e
sU n
t er
S t
un
d en
z ei g
er
U nd e
r h o
ur
h an
d
S ou
s l ' a
i gu
i l le
d e
s m
i nu
t es
U nt e
r
Mi n
ut e
nz e
i ge
rU n
d er
mi n
ut e
h a
nd
Peinture comprise / inkl. Farbe / Paint includedEpaisseur maximum du cadran
Maximale ZifferblattdickeMaximum dial thickness
0.552.10 0.550.55
E pa
i ss e
ur
d es
ai g
ui l l
es
Z ei g
er d
i ck e
Ha
nd s
t h
i ck n
es s
0.15
AiguillagesZeigerwerkhhe
Hand fitting height
No
1
-
P et i t
e
s ec o
nd e
K le
i ne
S e
k un
d eS m
al l
s ec o
nd
P ig n
on
c o
mp t
eu
rZ
h le
r t ri e
bC o
un
t er
p in
i on
J J
P ig n
on
d e
s s e
c on
d es
c hr o
no
S to
p p-
S ek u
nd e
nt r i
eb
C hr o
no
s e
c on
d p i
ni o
n
C ha
us s
eM
i nu
t en
r oh r
C an
no
n-
p in
i on
Ro
ue
d e
s h e
ur e
sS t
un
d en
r ad
Ho
ur
wh e
el
Dpassement Hhe ber Zifferblattauflage
Height over dial seat
2.61
G
1.95 1.521
AiguillagesZeigerwerkhhe
Hand fitting height
E FNo H
1.15
-
1.00 1.00 1.00
J
P ig n
on
d e
s j o u
r s
r t r o
g ra
d eT a
g es a
nz e
i ge
t r ie
b r e
t r og r
ad
Da
y p i
ni o
n
r et r o
g ra
d e1
ai g
.
1 Z e
i ge
r1
Ha
nd
N
1.05
J
0 .3 5
ConicitKonizittConicity2%
0 .3J
+6 -4 0.206
0 .3
0 .3
+6 -4 0.206
Ajustement aiguilleZeigerpassungHand fitting
HConicitKonizittConicity2%
0 .3
0.256 +6-4
0.5 max.
0.200
15 Okt 2014 dhA 13275
N N
-
RONDA 8040.B, 8040.N
Tige (dimensions / forces)Stellwelle (Dimensionen / Krfte)Stem (dimensions / forces)
Issued
---
Scale
Tolerance
10:1 (A3)
00
07 Sep 2012
No.
ds5222
Sous rserve de modificationsAenderungen vorbehalten
Modifications reserved
5030.023
Modified
Released YES
---
A 11741ds5222
L2
L
S
L1L3
No. d'articleArtikelnummerPart number
L L1
3000.203.CO
L2 L3 S DCouleur de la couronneKronenfarbeCrown color
21.30 11.67 28.57 11.12 1.100.90
gris fonc
UN 7005
Tige de travail (intgre dans le mouvement)Arbeitstellwelle (im Werk eingebaut)Working stem (implemented in the movement)
Code
dunkelgraudark grey
No. d'articleArtikelnummerPart number
L L1
3000.203
L2 L3 S D
21.30 11.67 28.57 11.12 1.100.90
Tige (normale) / Stellwelle (normal) / Stem (normal)
No. d'articleArtikelnummerPart number
L4 L5(min)
3000.040
L6 S1 S2 D1
12.00 1.90 2.45 0.90 1.350.90
Rallonge de tige / Stellwelle Verlngerung / Stem extension S2
L4
L5
S1 D1
d'encageage / Gehusepassungs- / Case fitting
Bote / Gehuse / Case
0.02 - 0.10
Couronne normaleNormale KroneNormal crown
D
L6
Force min.Kraft min.Force min.
10 N
Force max.Kraft max.Force max.
15 N
Couronne visseGeschraubte KroneScrewed crown
-
DOMVT096e T2 Information
Version: 1.1
Prozess: 3.1.3
Casing instructions RONDA mastertech 8040.N nd. Dat:30.04.2010
5331 (RONDA WEB PAGE)
Ersteller: fb5163 Geprft: hh5160 Freigabe IQ Soft: ah5256 / ea5250
Information & references Case & pushers Frame drawing Dial, positions of counters & day Dial drawing Hand fitting heights & specifications for hands Hand fitting heights drawing Adjustment of functions Users manual
Dial & hand setting 1. Note the by the working hand indicated day (example: 2 = TUE = Tuesday) 2. Remove working hands 3. Set dial 4. Set WEEKDAY hand to the same day (example: 2 = TUE = Tuesday)
or
1. Stem in position 3: Turn crown forwards until weekday hand has jumped back to Position 1
2. Remove working hands 3. Set dial 4. Set WEEKDAY hand to Monday
5. Set SECOND hand, HOUR and MINUTE counters to arbitrary index 6. Stem in position 2: Turn crown backwards until date 02 is indicated 7. Stem in position 3: Turn crown forwards until date has jumped from 02 to 03 8. Set HOUR and MINUTE hands to 12 oclock 9. Set SECOND counter to arbitrary index
Calendar changing phases & times Date ~ 1 - 2 h Weekday ~ - 2 h after the date change
Initialisation of chronograph hands 10. To ensure proper positioning of the chronograph hands to the zero position, a complete initialisation must be
issued after the hand setting operation is completed. Viz.: Each counter must be adjusted 1x to the zero position. 11. End: Push stem back in position 1.
Movement holder
Remark During the date setting with quick mode (stem in position 2), the speed may not exceed 5 days / second.
Pull out stem in position 3
Keep pushers A & B depressed for at least 2 seconds
Adjust the counter to the zero position by activating pusher A
Press pusher B one time Change to the next counter
A Hand setting T Stem removal Part number H 80XX.1A4 Part number H 80XX.1T
The movement needs to be supported for hand setting.
Maximal force: Hour & minute hands: max. 40N All other hands: max. 30N
For removal of the stem, the stem must be pushed into position 1 (pressed in) prior to apply pressure to the setting lever.
Information re BIG DATE An extreme acceleration in setting the date with quick mode (BIG DATE) can induce a false date indication. The synchronization is re-established by setting the date from 01 till 31 (stem in position 2).
A
B
1 2 3
-
Wichtig! Die Hhe der Absttzschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster lhauteur des vis de support au pralable de chaque srie. Important! Adjust height of support screws prior to each series.
Erstellt: fb5163 Geprft: hh5160 Freigabe IQ-Soft: ah5256 / ea5250 Seite 1/8
Werkhalter T2 Porte-pice T2
Movement holder T2
DOMVT004
Version: 1.9
Verwendung & bersicht Utilisation & Vue densemble
Utilisation & Overview
Prozess: 3.1.3
nd.-Dat.: 04.04.2014 5110, 5112, 5150, 5151, 5152, 5160, 5161, 5163, 5164, 5166, 5310, 5311, 5312, RTC, RHK Ermano, Pine Precision AF Switzerland SA, Horotec SA, Tschudin & Schneider
A Zeiger setzen
T Stellwelle entfernen Diverses
Poser les aiguilles Enlever la tige Divers
Hand setting Stem removal Various
Kalibergruppe Artikelnummer
Artikelnummer
Artikelnummer Groupe de calibre Numro darticle Numro darticle Numro darticle Calibre group Part number Part number Part number
Z60 H ZXX.1A H ZXX.1T
Z60
8000-8499 H 80XX.1A H 80XX.1T
8040.B 8040.N
7000-7999 H 7XXX.1A H 7XXX.1T
700X.B 700X.L 700X.N 700X.P
-
Wichtig! Die Hhe der Absttzschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster lhauteur des vis de support au pralable de chaque srie. Important! Adjust height of support screws prior to each series.
DOMVT004 / Version: 1.9 / Prozess: 3.1.3 / nd.-Dat.: 04.04.2014 Seite 2/8
A Zeiger setzen
T Stellwelle entfernen
P Alarm-Check
Poser les aiguilles Enlever la tige Contrle dalarme
Hand setting Stem removal Alarm check
Kalibergruppe Artikelnummer
Artikelnummer
Artikelnummer Groupe de calibre Numro darticle Numro darticle Numro darticle Calibre group Part number Part number Part number
6000-6999 H 6XXX.1A H 6XXX.1T
6XXX.B 6XXX.D
Swiss Made Swiss Parts
4000-5999.B/.C/.D/.E H 5XXX.1A H 5XXX.1T H 5XXX.1P
4XXX.B 5XXX.B 5XXX.C 5XXX.D 5XXX.E
4000-5999.F H 5XXX.FA H 5XXX.1T H 5XXX.1P
5XXX.F (4XXX.B) (5XXX.B) (5XXX.C) (5XXX.D) (5XXX.E)
-
Wichtig! Die Hhe der Absttzschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster lhauteur des vis de support au pralable de chaque srie. Important! Adjust height of support screws prior to each series.
DOMVT004 / Version: 1.9 / Prozess: 3.1.3 / nd.-Dat.: 04.04.2014 Seite 3/8
A Zeiger setzen
T Stellwelle entfernen Diverses
Poser les aiguilles Enlever la tige Divers
Hand setting Stem removal Various
Kalibergruppe Artikelnummer
Artikelnummer
Artikelnummer Groupe de calibre Numro darticle Numro darticle Numro darticle Calibre group Part number Part number Part number
3500-3999 H 35XX.1A H 35XX.1T
3520.D 3540.D
1062-1069 H 106X.1A H 106X.1T
1062 1063 1064 1069
Swiss Made Swiss Parts
6h
6h
1062
- - - -
1063
-
-
1064
-
-
1069
- - - -
1042 H 1042.1A H 1042.1T
1042
-
Wichtig! Die Hhe der Absttzschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster lhauteur des vis de support au pralable de chaque srie. Important! Adjust height of support screws prior to each series.
DOMVT004 / Version: 1.9 / Prozess: 3.1.3 / nd.-Dat.: 04.04.2014 Seite 4/8
A Zeiger setzen
T Stellwelle entfernen Diverses
Poser les aiguilles Enlever la tige Divers
Hand setting Stem removal Various
Kalibergruppe Artikelnummer
Artikelnummer
Artikelnummer Groupe de calibre Numro darticle Numro darticle Numro darticle Calibre group Part number Part number Part number
1032 H 1032.1A H 1032.1T
1032
1012-1019 H 101X.1A H 101X.1T
1012 1013 1014 1015 1016 1019
1002-1009 H 100X.1A H 100X.1T
1002 1003 1004 1005 1006 1009
-
Wichtig! Die Hhe der Absttzschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster lhauteur des vis de support au pralable de chaque srie. Important! Adjust height of support screws prior to each series.
DOMVT004 / Version: 1.9 / Prozess: 3.1.3 / nd.-Dat.: 04.04.2014 Seite 5/8
A Zeiger setzen
T Stellwelle entfernen Diverses
Poser les aiguilles Enlever la tige Divers
Hand setting Stem removal Various
Kalibergruppe Artikelnummer
Artikelnummer
Artikelnummer Groupe de calibre Numro darticle Numro darticle Numro darticle Calibre group Part number Part number Part number
782-788 H 78X.1A H 78X.1T
782 783 784 785 788
Swiss Made Swiss Parts
772-775 H 77X.1A H 77X.1T
772 773 774 775
Swiss Made Swiss Parts
-
Wichtig! Die Hhe der Absttzschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster lhauteur des vis de support au pralable de chaque srie. Important! Adjust height of support screws prior to each series.
DOMVT004 / Version: 1.9 / Prozess: 3.1.3 / nd.-Dat.: 04.04.2014 Seite 6/8
A Zeiger setzen
T Stellwelle entfernen Diverses
Poser les aiguilles Enlever la tige Divers
Hand setting Stem removal Various
Kalibergruppe Artikelnummer
Artikelnummer
Artikelnummer Groupe de calibre Numro darticle Numro darticle Numro darticle Calibre group Part number Part number Part number
762-763 H 76X.1A H 76X.1T
762 762E 763 763E
Swiss Made Swiss Parts
762
- -
762E
- -
763
-
763E
751-753 H 75X.1A H 75X.1T
751 753
Swiss Made Swiss Parts
751
- -
753
-
Wichtig! Die Hhe der Absttzschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster lhauteur des vis de support au pralable de chaque srie. Important! Adjust height of support screws prior to each series.
DOMVT004 / Version: 1.9 / Prozess: 3.1.3 / nd.-Dat.: 04.04.2014 Seite 7/8
A Zeiger setzen
T Stellwelle entfernen Diverses
Poser les aiguilles Enlever la tige Divers
Hand setting Stem removal Various
Kalibergruppe Artikelnummer
Artikelnummer
Artikelnummer Groupe de calibre Numro darticle Numro darticle Numro darticle Calibre group Part number Part number Part number
712-715 H 71X.1A H 71X.1T
712 713 714 715
Swiss Made Swiss Parts
702-708 H 70X.1A H 70X.1T
702 703 704 705 708 (706)
Swiss Made Swiss Parts
706 H 706.1A H 70X.1T
706.1 706.2 706.3 706.B
Swiss Made Swiss Parts
6h
6h
-
Wichtig! Die Hhe der Absttzschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster lhauteur des vis de support au pralable de chaque srie. Important! Adjust height of support screws prior to each series.
DOMVT004 / Version: 1.9 / Prozess: 3.1.3 / nd.-Dat.: 04.04.2014 Seite 8/8
A Zeiger setzen
T Stellwelle entfernen Diverses
Poser les aiguilles Enlever la tige Divers
Hand setting Stem removal Various
Kalibergruppe Artikelnummer
Artikelnummer
Artikelnummer Groupe de calibre Numro darticle Numro darticle Numro darticle Calibre group Part number Part number Part number
582-585 H 58X.1A H 58X.1T
582 583 585
512-519 H 51X.1A H 51X.1T
512 513 515 517 519
502-509 H 50X.1A H 50X.1T
502 503 505 507 509
-
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
I II III
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
I II III
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
I II III
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
III65,5% = 40mm Druchmesser
III
A
65,5% = 40mm Druchmesser
III
B
65,5% = 40mm Druchmesser
III
A
65,5% = 40mm Druchmesser
IIII II
65,5% = 40mm Druchmesser
III
B
65,5% = 40mm Druchmesser
III
A
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
I II III
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
I II III
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
1 7
30
1020
10 123
456789
II IIII
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 2
30
1020
10 123
456789
I II III
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
0 1
30
1020
10 123
456789
I II
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
3 1
30
1020
10 123
456789
I II
MON
TUE W
ED THU FRI SAT SUN
15
60
30
45
2 3
30
1020
10 123
456789
15
60
30
45
2 3
30
1020
10 123
456789
Display elements 8040.N
Minute hand110 second counter (houer counter after 30 minutes)
Day of the week handHour handMinute counterSecond counterSecond handDate
Chronograph: Basic function(Start / Stop / Reset)
Example: Start: Press push-button A.
Stop: to stop the timing, press push-button A once more and read the chronograph counters:
4 min / 38 sec / 710 sec
Zero positioning: Press push-button B. (The chronograph hands will be reset to
their zero positions.)
Chronograph: Accumulated timingExample: Start: (start timing)
Stop: (e.g. 15 min 5 sec following )
Restart: (timing is resumed)
* Stop: (e.g. 5 min 12 sec following ) = 20 min 17 sec (The accumulated measured time is shown)
Reset: The chronograph hands are returned to
their zero positions.
Please note:* Following , the accumulation of the
timing can be continued by pressing push-button A (Restart / Stop, Restart / Stop, ).
Chronograph: Intermediate or interval timingExample: Start: (start timing) Display interval: e.g. 20 minutes 17 seconds (timing
continues in the background) Making up the measured time: (the chronograph hands are quickly
advanced to the ongoing measured time.) Stop: (Final time is displayed) Reset: The chronograph hands are returned to
their zero position.
Please note: * Following , further intervals or inter-
mediates can be displayed by pressing push-button B (display interval / make up measured time, ...).
*
Adjusting the chronograph hands to zero positionExample: One or several chronograph hands are not in their correct zero positions and have to be adjusted (e.g. following a battery change).
Pull out the crown to position III (all chronograph hands are in their correct or incorrect zero position.)
Keep push-buttons A and B depressed simultaneously for at least 2 seconds (the second counter hand rotates by 360 corrective mode is activated.)
Adjusting the second counter handSingle step
65,5% = 40mm Druchmesser
III
A 1 x shortContinuous
65,5% = 40mm Druchmesser
III
A long
Adjusting the next hand B
65,5% = 40mm Druchmesser
III
Adjusting the 110 second counter hand (position 3h)Single step
65,5% = 40mm Druchmesser
III
A 1 x shortContinuous
65,5% = 40mm Druchmesser
III
A long
Adjusting the next hand B
65,5% = 40mm Druchmesser
III
Adjusting the minute counter hand (position 9h)Single step
65,5% = 40mm Druchmesser
III
A 1 x shortContinuous
65,5% = 40mm Druchmesser
III
A long
Returning the crown to position I
Termination of the chronograph hands adjustment (can be carried out at any time).
Setting the time
*Pull out the crown to position III (the watch stops).
Turn the crown until you reach the correct time 8:45.
* Push the crown back into position I.
Please note:* In order to set the time to the exact second, must be pulled out when the second hand is in position 60. Once the hour and minute hands have been set, must be pushed back into position I at the exact second.
Setting the date (quick mode)
Pull out the crown to position II (the watch continues to run).
Turn the crown anticlockwise until the correct date 01 appears.
Push the crown back into position I.
Please note:During the date changing phase between approx. 8 PM and 12 PM; the date must be set to the date of the following day.
An extreme acceleration in setting the date with quick mode can induce a false date indi-cation. The synchronization is re-established by setting the date from 01 till 31 (crown in position II).
Setting the date, day of the week (8040.N), time
Example: Date / time on the watch: 17 / 01:25 / MON Present date / time: 23 / 20:35 / SAT
Pull out the crown to position III (the watch stops).
Turn the crown until yesterdays day of the week FRI appears.
Push the crown to position II.
Turn the crown anticlockwise until yesterdays date appears 22 .
* Pull out the crown to position III (the watch stops). Turn the crown until the correct date 23 and day of the week SAT appears.
** Continue to turn the crown until the correct time 8:35 PM appears.
Push the crown back into position I.
Please note:* To set your watch to the exact second,
please refer to the chapter entitled setting the time.
** Please observe the AM/PM clock rhythm.
Users Manual English
RONDA mastertech Movement Cal. 8040.N & 8040.B
04 / 2014
Battery type: 395 (diameter 9.5 mm x 2.6 mm / SR 927 SW)Accuracy: +20 / -10 seconds per month
Display elements 8040.B
Minute hand110 second counter (houer counter after 30 minutes)
Date
Hour hand
Minute counter
Second counter
Second hand
Description of the display and control buttons
Control buttons
Push-button A & BCrown
Control buttons
Push-button A & BCrown
B B
A A
You have decided to buy a watch, which was assembled by a watch- maker using a Ronda movement. Please note that no watches are produced or distributed under the Ronda Brand.
In case of repairs, guarantee claims and questions concerning the functioning of a watch, purchasers and consumers should contact their retailer or the watch manufacturer, for which the relevant information can be found in the sales or guarantee documentation provided with the watch.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
01
05
02
06
03
07
04
08
-
Technical instructions 8040.N
10/2013 V RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 1
2000.700.CO Main plate1.
3406.038 Pusher jumper A2. Put the yellow jumper between the two posts on the closer side.-#13;
3406.030 Pusher jumper B3. Put the grey jumper between the two posts on the further side.
3305.364.CO Canon pinion (Aig.1)4.
A2030.029 Center bridge5. Center bride held by 2 screws 4000.250.
4000.250 Screw6.
3406.040 Friction spring7. Friction spring held by 1 screw 4000.250.
4000.250 Screw8.
3622.055 Stator9.
3622.054 Stator chrono10. Mark |1| on stator.
3715.119.RK Rotor11.
3715.119.RK Rotor12.
B
3147.073.CO Intermediate wheel13.
3147.074.CO Intermediate wheel chrono14.
3122.067.CO Third wheel15.
3136.180.CO Chronograph wheel16.
3136.179.CO Second wheel17.
3136.178.CO Small second wheel18.
3004.203.CO Reverse wheel19.
C
-
Technical instructions 8040.N
10/2013 V RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 2
2020.188.G Train wheel bridge20. Train wheel bridge held by 2 screws 4000.250. Mark |2|.
4000.250 Screw21.
3622.039 Stator counter (cpt 6h and 9h and chrono)22.
3402.012.CO Minute counting wheel23.
3715.120.RK Rotor24.
3147.076.CO Intermediate wheel (counter 30min)25.
D
2020.191.G Counter train wheel Bridge26. Train wheel bridge held by 2 screws 40000.250. Mark |2|.
4000.250 Screw27.
3622.039 Stator counter28.
3402.013.CO Counting wheel (1/10 s)29.
3715.120.RK Rotor30.
3147.075.CO Intermediate wheel (counter 1/10 s)31.
2020.190.G Counter train wheel bridge32. Train wheel bridge held by 2 screws 40000.250. Mark |2|.
4000.250 Screw33.
E
3016.029 Stop lever34. Stop lever held by 1 screw 4000.249.
4000.249 Screw35.
2130.222 Maintaining plate36. Maintaining plate held by 1 screw 4000.248.
4000.248 Screw37.
F
-
Technical instructions 8040.N
10/2013 V RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 3
3621.072.RK Coil centre38. Attention: Please hold the coil only on the grey coil core.
3621.055.RK Coil counter39. Attention: Please hold the coil only on the grey coil core.
3621.055.RK Coil counter40. Attention: Please hold the coil only on the grey coil core.
3621.055.RK Coil counter41. Attention: Please hold the coil only on the grey coil core.
4000.250 Screw42.G
3603.089 Battery insulator43.
3601.134 Pusher contact spring44.
3612.218 Electronic module45. Electronic module held by 6 screws. (Electronic measurements may berealised now.)
4000.248 Screw46. 4 screws 4000.248 for pressing the module on the coils.
4000.250 Screw47. 2 screws 4000.248 for pressing the module on the 2 posts.
3601.132.G Lateral bridle48. Lateral bridle held by 1 screw 4000.250.
4000.250 Screw49.
H
3603.090 Circuit insulator50.
2130.206.G.M01.8040N Electronic module cover51. Electronic module cover held by 4 screws 4000.250.
4000.250 Screw52.
3600.010.HGF Battery 39553.
3601.133.G Bridle +54. Bridle + held by 2 screws 4000.250.
4000.250 Screw55.
I
-
Technical instructions 8040.N
10/2013 V RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 4
2000.700.CO Main plate56.
J
3017.054.CO Setting lever57.
3001.046 Sliding pinion58.
3015.088 Yoke (3 positions)59.
3905.063 Setting lever jumper60. Lever held by 1 screw 4000.282.
4000.282 Screw61.
K
3004.200 Corrector setting wheel62.
3004.200 Corrector setting wheel63.
3015.087.CO Setting wheel yoke64.
L
-
Technical instructions 8040.N
10/2013 V RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 5
2130.208 Setting mecanism cover65. Setting meca cover held by 4 screws 4000.305.
4000.305 Screw66.
3000.203.CO Setting stem67.
3004.222 Intermediate setting wheel68.
3007.079.CO Minute wheel69.
2130.209 Minute train bridge70. Minute train bridge held by 3 screws 4000.278.
4000.278 Screw71.
M
2000.672.G Main plate retro72. Minute plate retro held by 4 screws 4000.248.
4000.248 Screw73.
N3004.220 Tens indicator driving wheel74. The short tooth of the tens indicator driving wheel must point to thecenter of the movement.
3500.072 Tens jumper75.
2130.187 Tens jumper maintaining plate76. Tens jumper maintaining plate held by 2 screws 4000.279. Tensioningthe spring arm.
4000.279 Screw77.
3301.292.CO Hour wheel78.
3004.208.CO Date indicator driving wheel79.
3147.061 Intermediate date wheel80.
O
-
Technical instructions 8040.N
10/2013 V RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 6
3404.006.CO Day cam81. Place parts as shown on graphics.
3406.032 Day rack82.
3406.031 Day rack lever83.
3147.066.CO Date corrector setting wheel84.
3507.059.CO Date corrector wheel85.P
2130.191 Date indicator plate86.
3905.068 Date corrector spring87. Date corrector spring held by 1 screw 4000.244.
4000.244 Screw88.
3905.066 Day rack lever spring89. Tensioning the spring arm.
3500.068 Date jumper90.
3500.069 Day jumper91. Tensioning the spring arm.
Q
-
Technical instructions 8040.N
10/2013 V RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 7
3504.234.AD.1.A Units indicator (standard)92. Nick of the indicator at 3 o`clock.
2130.192 Date indicator maintaining plate93. Date indicator maintaining plate held by 1 screw.
4000.250 Screw94.
3905.064 Date jumper spring95. Insert the date jumper spring in the previous opening.
3004.244 Day finger96. Stem pos III: Turn crown forwards until the date jumps. Stem pos II:Move the date until the nick is at 3 o`clock. Position the end of the
teeth against the day came pinion while turning softly incounterclockwise direction.
3004.212 Days driving wheel97. Insert the tooth of the wheel in the flange gap, while turning softly incounterclockwise direction to ensure correct position of the day finger.
3401.086.FI Day indicator pinion98.
3147.062 Tens intermediate wheel99. Arrow positioning radially outwards.
3504.231.AD.1.A Tens indicator (standard)100. Nick of the indicator at 3 o`clock.
3315.003 Friction spring101.
2130.193.G Date mecanism maintaining plate102. Date maca maintaining plate held by 3 screws 4000.320.
4000.320 Screw103.
3506.077.G Intermediate Dial support104. Polished version first.
3506.076.G Dial support105.
8200 Moebius 8200106.
9014 Moebius 9014107.
124 Jismaa 124108.
9020 Moebius 9020109.
R
S
-
10/2013 RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] EM 1
Electronic measurements
8040.N
Battery 395
Voltage 1.55 V
Setting stem in position I, calendar not in gear, 60 s measuring interval for rate and consumption:
Typical consumption Maximal consumption
1.48 A 2.00 A
Rate -10s/M. .. +20s/M.
Lower working voltage limit 1.20 V
Hold down the electrical module to allow the electronic flow.
Setting stem in position III, 60 s measuring interval:
Typical consumption Maximal consumption
0.10 A 0.30 A
-
10/2013 RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] EM 2
Electronic measurements
8040.N
Coil resistance M1 1.50 k .. 1.70 k
Coil resistance M2 1.68 k .. 1.88 k
Coil resistance M3 1.68 k .. 1.88 k
Coil resistance M4 1.68 k .. 1.88 k
Coil isolation M1/M2/M3/M4 k
Signal generator (4.9 ms, 8 Hz):
Lower working voltage limit M2/M3/M4 1.20 V
-
Technical instructions 8040.N
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 1
2000.700.CO Main plate1.
3406.038 Pusher jumper A2. Put the yellow jumper between the two posts on the closer side.
3406.030 Pusher jumper B3. Put the grey jumper between the two posts on the further side.
3305.364.CO Canon pinion (Aig.1)4.
A2030.029 Center bridge5. Center bride held by 2 screws 4000.250.
4000.250 Screw6.
3406.040 Friction spring7. Friction spring held by 1 screw 4000.250.
4000.250 Screw8.
3622.055 Stator9.
3622.054 Stator chrono10. Mark |1| on stator.
3715.119.RK Rotor11.
3715.119.RK Rotor12.
B
3147.073.CO Intermediate wheel13.
3147.074.CO Intermediate wheel chrono14.
3122.067.CO Third wheel15.
3136.180.CO Chronograph wheel16.
3136.179.CO Second wheel17.
3136.178.CO Small second wheel18.
3004.203.CO Reverse wheel19.
C
-
Technical instructions 8040.N
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 2
2020.188.G Train wheel bridge20. Train wheel bridge held by 2 screws 4000.250.
4000.250 Screw21.
3622.039 Stator counter (cpt 6h and 9h and chrono)22.
3402.012.CO Minute counting wheel (30min)23.
3715.120.RK Rotor24.
3147.076.CO Intermediate wheel (counter 30min)25.
D
2020.191.G Counter train wheel Bridge (2h30)26. Train wheel bridge held by 2 screws 40000.250. Mark |2|.
4000.250 Screw27.
3622.039 Stator counter28.
3402.013.CO Counting wheel (1/10 s)29.
3715.120.RK Rotor30.
3147.075.CO Intermediate wheel (counter 1/10 s)31.
2020.190.G Counter train wheel bridge32. Train wheel bridge held by 2 screws 40000.250. Mark |1|.
4000.250 Screw33.
E
3016.029 Stop lever34. Stop lever held by 1 screw 4000.249.
4000.249 Screw35.
2130.222 Maintaining plate36. Maintaining plate held by 1 screw 4000.248.
4000.248 Screw37.
F
-
Technical instructions 8040.N
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 3
3621.072.RK Coil centre38. Attention: Please hold the coil only on the grey coil core.
3621.055.RK Coil counter39. Attention: Please hold the coil only on the grey coil core.
3621.055.RK Coil counter40. Attention: Please hold the coil only on the grey coil core.
3621.055.RK Coil counter41. Attention: Please hold the coil only on the grey coil core.
4000.250 Screw42.G
3603.089 Battery insulator43.
3601.134 Pusher contact spring44.
3612.218 Electronic module45. Electronic module held by 6 screws.
4000.248 Screw46. 4 screws 4000.248 for pressing the module on the coils.
4000.250 Screw47. 2 screws 4000.248 for pressing the module on the 2 posts.
3601.132.G Lateral bridle48. Lateral bridle held by 1 screw 4000.250.
4000.250 Screw49.
H
3603.090 Circuit insulator50.
2130.206.G.M01.8040N Electronic module cover51. Electronic module cover held by 4 screws 4000.250.
4000.250 Screw52.
3600.010.HGF Battery 39553.
3601.133.G Bridle +54. Bridle + held by 2 screws 4000.250.
4000.250 Screw55.
I
-
Technical instructions 8040.N
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 4
2000.700.CO Main plate56. .
J
3017.054.CO Setting lever57.
3001.046 Sliding pinion58.
3015.088 Yoke (3 positions)59.
3905.063 Setting lever jumper60. Lever held by 1 screw 4000.282.
4000.282 Screw61.
K
3004.200 Corrector setting wheel62.
3004.200 Corrector setting wheel63.
3015.087.CO Setting wheel yoke64.
L
-
Technical instructions 8040.N
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 5
2130.208 Setting mecanism cover65. Setting meca cover held by 4 screws 4000.305.
4000.305 Screw66.
3000.203.CO Setting stem67.
3004.222 Intermediate setting wheel68.
3007.079.CO Minute wheel69.
2130.209 Minute train bridge70. Minute train bridge held by 3 screws 4000.278.
4000.278 Screw71.
M
2000.672.G Main plate retro72. Minute plate retro held by 4 screws 4000.248.
4000.248 Screw73.
N3004.220 Tens indicator driving wheel74. The short tooth of the tens indicator driving wheel must point to thecenter of the movement.
3500.072 Tens jumper75.
2130.187 Tens jumper maintaining plate76. Tens jumper maintaining plate held by 2 screws 4000.279. Tensioningthe spring arm.
4000.279 Screw77.
3301.292.CO Hour wheel78.
3004.208.CO Date indicator driving wheel79.
3147.061 Intermediate date wheel80.
O
-
Technical instructions 8040.N
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 6
3404.006.CO Day cam81. Place parts as shown on graphics.
3406.032 Day rack82.
3406.031 Day rack lever83.
3147.066.CO Date corrector setting wheel84.
3507.059.CO Date corrector wheel85.P
2130.191 Date indicator plate86.
3905.068 Date corrector spring87. Date corrector spring held by 1 screw 4000.244.
4000.244 Screw88.
3905.066 Day rack lever spring89. Tensioning the spring arm.
3500.068 Date jumper90.
3500.069 Day jumper91. Tensioning the spring arm.
Q
-
Technical instructions 8040.N
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 7
3504.234.AD.1.A Units indicator (standard)92. Nick of the indicator at 3 o`clock.
2130.192 Date indicator maintaining plate93. Date indicator maintaining plate held by 1 screw4000.250.
4000.250 Screw94.
3905.064 Date jumper spring95. Insert the date jumper spring in the previous opening.
3907.047 Day finger flange96. Stem pos III: Turn crown forwards until the date jumps. Stem pos II:Move the date until the nick is at 3 o`clock.
3004.211 Day finger97. Position the end of the teeth against the day came pinion while turningsoftly in counterclockwise direction.
3004.212 Days driving wheel98. Insert the tooth of the wheel in the flange gap, while turning softly incounterclockwise direction to ensure correct position of the day finger.
3401.086.FI Day indicator pinion99.
3147.062 Tens intermediate wheel100. Arrow positioning radially outwards.
3504.231.AD.1.A Tens indicator (standard)101. Nick of the indicator at 3 o`clock.
3315.003 Friction spring102.
2130.193.G Date mecanism maintaining plate103. Date maca maintaining plate held by 3 screws 4000.320.
4000.320 Screw104.
3506.077.G Intermediate Dial support105. Polished version first.
3506.076.G Dial support106.
8200 Moebius 8200107.
9014 Moebius 9014108.
124 Jismaa 124109.
9020 Moebius 9020110.
R
S
-
10/2013 RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] EM 1
Electronic measurements
8040.N
Battery 395
Voltage 1.55 V
Setting stem in position I, calendar not in gear, 60 s measuring interval for rate and consumption:
Typical consumption Maximal consumption
1.48 A 2.00 A
Rate -10s/M. .. +20s/M.
Lower working voltage limit 1.20 V
Hold down the electrical module to allow the electronic flow.
Setting stem in position III, 60 s measuring interval:
Typical consumption Maximal consumption
0.10 A 0.30 A
-
10/2013 RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] EM 2
Electronic measurements
8040.N
Coil resistance M1 1.50 k .. 1.70 k
Coil resistance M2 1.68 k .. 1.88 k
Coil resistance M3 1.68 k .. 1.88 k
Coil resistance M4 1.68 k .. 1.88 k
Coil isolation M1/M2/M3/M4 k
Signal generator (4.9 ms, 8 Hz):
Lower working voltage limit M2/M3/M4 1.20 V
Powered by TCPDF (www.tcpdf.org)