RITES · PDF fileRITES LTD. OPEN TENDER ... working load not less than specified incl. cost...

Signature of the tenderer 1 under seal of the firm

RITES LTD

OPEN TENDER NOTICE NO: 139/OT/RCF-BGB/Administrativ e Bldg/2012 Dated 14.02.2012

TENDER DOCUMENT FOR

Construction of Administrative building includi ng internal

electrification, GRP/SMC panelled overhead tank over steel structure staging, Pump house, Deep Tubewell boring, RCC Overground

Reservoir & pipeline network etc. in connection with Bogie & AC container manufacturing factory at Budge Budge of RCF

Part – 2 (FINANCIAL BID)

(PERCENTAGE RATE TENDER)

FEBRUARY – 2012

Issued to (Name of Tenderer):________________________________________ Address of tenderer:_________________________________________________ Signature of officer issuing the documents___________________ Designation _______________________________ Date of Issue___________________

RITES LTD (A Govt. of India Enterprise)

Regional Project Office, KOLKATA 56, C. R. Avenue, 2nd floor, Kolkata – 700 012

e.mail : [email protected] Phone No: (033) 2236 7118/7146/7162/7143(Fax)


PART – 2

FINANCIAL BID

SCHEDULE (BILL) OF QUANTITIES


RITES LTD.

OPEN TENDER NOTICE NO: 139/OT/RCF-BGB/Administrativ e Bldg/2012 Dated 14.02.2012

Name of work: Construction of Administrative building including internal electrification,

GRP/SMC panelled overhead tank over steel structure staging, Pump house, Deep Tubewell boring, RCC Overground Reservoir & pipeline network etc. in connection with Bogie & AC container manufacturing factory at Budge Budge of RCF

Completion Time: The time allowed for overall completion of the work is 9 (Nine) months but as per priority, construction upto 1st floor level of the Administrative Building shall be completed within 6 (Six) months 15th day after the date of issue of Letter of Acceptance or from the first day of handing over of the site, whichever is later, in accordance with the phasing, if any, indicated in the Tender Documents

RATE INDEX

( Percentage Rate Tender )

TENDERER SHOULD QUOTE THEIR RATES HERE UNDER ONLY

1. CIVIL ENGINEERING WORKS:

Sl. No Schedule No. Estimated Cost (In Rs.)

Quoted rates by bidders (Percentage above or below)

1 Schedule A

(RCC Bored Piling work)

68,76,924.30 Rate quoted are _________________ % (in

Figures)________________________

(in words) above /below * on schedule in A

2 Schedule B

(General works)


Figures)________________________

(in words) above /below * on schedule in B

3 Schedule B-I

(Brick work)


Figures)________________________

(in words) above /below * on schedule in B-I

4 Schedule B-II

(Concrete & Shuttering work)


Figures)________________________

(in words) above /below * on schedule in B-II

5 Schedule B-III

(Supply of Reinforcement

Steel)

1,52,59,200.00 Rate quoted are _________________ % (in

Figures)________________________

(in words) above /below * on schedule in B-III


6 Schedule B-IV

(Supply of Cement)


Figures)________________________

(in words) above /below * on schedule in B-IV

7 Schedule B-V

(plumbing & Sanitary works)


Figures)________________________

(in words) above /below * on schedule in B-V

8 Schedule C

(Supply & Installation of

Modular Workstation


Figures)________________________

(in words) above /below * on schedule in C

9 Schedule D

(Supply of GRP/SMC

panelled Overhead Tank over Steel

Structure Staging)


Figures)________________________

(in words) above /below * on schedule in D

10 Schedule E

(Deep Tubewell work)


Figures)________________________

(in words) above /below * on schedule in E

11 Schedule F

(Any other unforeseen items)


Figures)________________________

(in words) above /below * on schedule in F

12 Schedule G

(Internal Electrification

work)


Figures)________________________

(in words) above /below * on schedule in G

Total 6,68,59,532.00

* Strike out which is not applicable i) SIGNATURE OF AUTHORISED SIGNATORY OF TENDERER

ii) NAME OF SIGNATORY iii) NAME AND SEAL OF TENDERER

iv) DATE

v) PLACE


Note:

i) TENDERERS ARE REQUESTED TO QUOTE THEIR RATE IN THE PREVIOUS PAGE ONLY AND NOT IN SCHEDULES. BASIC RATES HAS BEEN SHOWN IN SCHEDULES FOR GUIDENCE.

ii) THE SUCCESSFUL BIDDER WHO WILL BE AWARDED THE WORK WILL HAVE TO SUBMIT TAX INVOICE BEFORE RECEIVING PAYMENT FROM RI TES’.


SCHEDULE OF QUANTITY

Sl. No. Description of Item Unit Qty. Rate

(Rs.) Amount

(Rs.)

Schedule - A (RCC Bored Piling work)

Boring, providing and installing bored cast-in-situ reinforced cement concrete pile of all length M-25 grade to carry a safe working load not less than specified incl. cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and pile to be embedded in the pile cap etc. all incl. removal of excavated earth with all lifts and leads beyond land boundary limit. Length of pile for payment shall be measured from founding level to cut off level of pile. Payment for steel reinforcement & cement will be made separately.

1

600mm dia. Piles Note:- i) The above rate includes mobilization & de-mobilization of equipment, breaking of foam concrete of cast piles, removal of bentonite muck from the factory premises etc complete in all respect.

M 3990 1658.91 6619050.90

2 Conducting load testing of a single pile upto following capacity in accordance with IS:2911 (Part-IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. with all labour, material, tool & plants, equipment, machinery, etc. complete as per drawing and specification, as directed by the Engineer -IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. with all labour, material, tool & plants, equipment, machinery, etc. complete as per drawing and specification, as directed by the Engineer Single pile above 50 tonne and upto 100 tonne capac ity - routine test

Each 4 38252.00 153008.00

3 Lateral load testing of single pile in accordance with I.S. Code of practice IS: 2911 ( Part IV )for determining safe allowable lateral load on pile for determining safe allowable lateral load on pile Vertical load capacity above 50 tonne and upto 100 tonne

Each 4 26216.35 104865.40

Cost of Schedule - A 6876924.30

Schedule - B (General works)

1 Earth work in excavation as per approved drawings and dumping at embankment site or spoil heap, within railway land, including 50m lead and 1.5m lift, the lead to be measured from the centre of gravity of excavation to centre of gravity of spoil heap; the lift to be measured from natural ground level and paid for in layers of 1.5m each including incidental work, as per specifications all kinds of soils The cost of earthwork in excavation is including of Shoring &

cum 1775 88.16 156484.00


Dewatering Extra for every additional lift of 1.5m or part thereof after the initial 1.5m for earth work in all soils

cum 670 8.62 5775.40

2 Extra over item 1 above for excavation in foundations for buildings and bridges to cover dressing to neat dimension and plumbing sides etc. Note : Dressing under this item is payable for the total quantity of excavation in foundation and not partly.

cum 1775 9.20 16330.00

3 Extra for lead of earthwork above initial lead of 50m in all kind of soils:

For every 50m or part thereof - lead over 50m and upto 150m cum 400 11.50 4600.00

For every 50m or part thereof - lead over 150m and upto 500m cum 1300 9.10 11830.00

4 Filling, watering and ramming earth in 15cm layers in floors and foundations with surplus earth from foundations including 50m lead and 1.5m lift.

cum 1225 20.40 24990.00

5 Supplying and filling sand in plinth and under floors including watering, ramming, consolidating and dressing complete. cum 572 359.67 205731.24

6 Flat Brick flooring with bricks of class designation 7.5 including cement slurry etc. complete in cement mortar r 1:4 (1 cement : 4 coarse sand) (with FPS Bricks)

Sqm 900 192.07 172863.00

7 Providing and fixing in position 12mm thick bitumen impregnated fibre board conforming to IS:1838 including cost of primer, sealing compound in expansion joints. (1200cm x 10.7m) /100

per cm

depth/ 100m length

130 491.66 63915.80

8 Treatment of expansion joints by cleaning the joint and surfaces abutting the expansion joint, applying two coats of primer on the cleaned surfaces at the opening of the joint, filling the joint (to a depth equaling half the width) with the paste of a two-component polysulphide based sealant with base-curing agent weight ratio of 12.33:1 and a sp.gr. of cure in natural air for at least a day, providing the edges of the treatment with two coats of a paste of octadecanoic acid based cementitious waterproofing compound and acrylic-styrene based copolymer waterproofing material in the weight ration of 1:3

metre 130 950.54 123570.20


9 Water proofing of roofs and exposed concrete surfac es using polymeric waterproofing compound by cleaning and drying the surface; applying two coats (DFT of 200-300 micron) of translucent brown coloured phenolic resin based single component high performance polymeric waterproofing compound @ 0.6 litre per sqm, with demonstrable properties of resistance to water and acid; spraying a layer of dry coarse sand on the second coat when still wet; removing excess sand on the following day; permitting to coatings to cure and dry naturally for 3-7 days; providing a 12mm thick cement-sand (1:4) cover plaster; curing the plaster; the treatment shall be impermeable under a waterhead of 20m (removal of existing damaged waterproofing system, PCC, Lime Terracing etc., if any to be paid extra under separate item).

Sqm 645 275.34 177594.30

10 Making drain mouth on roof waterproof by cleaning the surface of the structure at the location of drain mouth; lowering the drain mouth to the level of the concrete roof; chipping thorough cleaning; mixing throughly an octadecanoic acid based cementitious waterproofing compound in the weight ratio of 50 cement (OPC or slag) and 3 waterproofing compound; placing the drain mouth in its final position, followed by filling of the annular space around the drain pipe with a paste of waterproofing compound-cement; sealing the edges of the drain mouth with acrylic-styrene based copolymer waterproofing compound

Each 12 465.88 5590.56

11 Water proofing surface treatment inside walls and floors of water reservoirs by cleaning the surface, preparing the surface by acid etching, treating the surface with a two layer plaster, first layer shall be 7/6 mm thick with octadecanic acid based cementitious waterproofing compound and cement in the weight ratio of 3:50 for waterproofing compound and cement-sand (1:2 on floors of basements and tunnels, 1:3 elsewhere) plaster (12mm thick on floor, 8mm thick on vertical surfaces and at ceiling) and curing the plastered surface paring the surface by acid etching, treating the surface with a two layer plaster, first layer shall be 7/6 mm thick with octadecanic acid based cementitious waterproofing compound and cement in the weight ratio of 3:50 for waterproofing compound and cement-sand (1:2 on floors of basements and tunnels, 1:3 elsewhere) plaster (12mm thick on floor, 8mm thick on vertical surfaces and at ceiling) and curing the plastered surface Inside Water Reservoir

Sqm 450 389.97 175486.50

12 Arresting water leakages at isolated locations (points of leakage), at cracks and at construction joints with a putty of cement (OPC or slag), modified with a cementitious quick setting compound in a weight ratio of 1:10 and modified with a silica waterproofing compound having the properties of making cement quick setting and non-shrinking in quantities to suit the water pressure conditions at the site and finally topping the plugged material with a surface waterproofing treatment with a putty of cement (OPC or slag), modified with a cementitious quick setting compound in a weight ratio of 1:10 and modified with a silica waterproofing compound having the properties of making cement quick setting and non-shrinking in quantities to suit the water pressure conditions at the site and finally topping the plugged

Each 15 477.33 7159.95


material with a surface waterproofing treatment For Leakage points

13 15mm cement plaster finished with a floating coat of neat cement of mix - 1:4h a floating coat of neat cement of mix - 1:4 (1 cement : 4 fine sand) Sqm 4325 71.56 309497.00

14 20mm cement plaster on the rough side of single or half brick wall of mix - 1:4 (1 cement : 4 fine sand) of single or half brick wall of mix - 1:4 (1 cement : 4 fine sand)

Sqm 1610 83.37 134225.70

15 Cement plaster to ceiling of mix - 12mm thick - 12mm thick 1:4 (1 cement : 4 fine sand)

Sqm 2040 62.44 127377.60

16 Providing and applying plaster of Paris putty of 2mm average thickness over plastered surface to prepare the surface even and smooth complete Sqm 6400 76.54 489856.00

17 Applying one coat of cement primer of approved brand and manufacture on wall surface Sqm 6530 25.16 164294.80

18 Finishing walls with Acrylic smooth interior paint of required shade on new work (two or more coats applied @1.67 litre/10sqm over and including base coat of water proofing cement paint applied @2.20 kg/10aqm

Sqm 6530 86.47 564649.10

19 Extra for appiying water proofing cementpaint as primer applied @ 2.2kg/ 10sqm instead of primer for exterior finishing Sqm 1480 2.86 4232.80

20 Finishing walls with Acrylic smooth Exterior paint of required shade on new work (two or more coats applied @1.67 litre/10sqm over and including base coat of water proofing cement paint applied @2.20 kg/10aqm

Sqm 1630 91.31 148835.30

21 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coats applied @ 0.90 litre/10sqm over an under coat of primer applied @ 0.80 litre/10sqm of approved brand or manufacture. Deduct cost of applying priming coat red oxide zink chormate. (72.63-10.52=62.11)

Sqm 194 62.11 12049.34

22 Providing and fixing ceramic tiles conforming to IS:15622 of manufacturers approved by railway in all colours, shades, design and abrasion resistance class as approved by the Engineer-in-Charge in floors and landings over 20mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) including pointing in white cement mixed with pigment of matching shade complete of Group B-I-a of IS:15622 (Vitrified tiles) of size above 400mm x 400mm upto 600mm x 600mm (For entire floor area except bathroom, Reception area, Staircase & Corridor area )

Sqm 1200 1102.32 1322784.00


23 Of Group B-II Clause 5.1 (for abrasion resistance ) of IS:15622 (Ceramic Floor Tiles ) of size 400mm x 400mm and above (For bathroom floor) Sqm 95 598.88 56893.60

24 Providing and fixing 1st quality ceramic tiles conforming to Group B-III (Ceramic wall tiles ) of IS: 15622 of manufacturers approved by railway in all colours, shades, and design as approved by the Engineer-in-charge in skirting, risers of steps and dado over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mixed with pigment of matching shade complete 200 x 300 mm (For bathroom wall, kitchen & Pantry w all)

Sqm 332 673.17 223492.44

25 Providing and fixing 10mm thick heavy duty acid and/or alkali resistant factory made tiles conforming to Group V-RD series of approved make and colour using acid and /or alkali resisting mortar bedding and joint filled with acid and /or alkali resistin cement as per IS : 4457 complete including cost of acid and /or alkali resistin cement in flooring on a bed of 10mm thick mortar 1:4 (For CMT laboratory)

Sqm 45 1076.43 48439.35

26 Kota stone slab flooring of size up to 60cm×60cm over 20mm (average) thick base of 1:4 cement morter (1cement : 4 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete t : 4 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete 20 mm thick (For Staircase, Corridor area, Reception area)

Sqm 770 1169.69 900661.30

27 Providing and fixing 18mm thick mirror polished, machine cut for kitchen platforms , facias and similar locations of required size of approved shade, colour & texture laid over 20mm thick base cement mortar 1:4 (1 cement:4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. complete at all levels. Granite Black-Area of slab over 1.0 sqm but upto 2. 0 sqm or larger (For Kitchenette & Pantry)

Sqm 8 3646.55 29172.40

28 Providing wood work in frames of doors, windows, clerestory windows and other frames and trusses, wrought, framed and fixed in position : Sal wood

Cudm 3500 52.03 182105.00

29 Providing and fixing flush door shutters to IS: 2202 Part-I non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3-ply veneering with vertical grains of cross bands and face veneers on both faces of shutters 35 mm thick including ISI marked stainless steel butt hinges with necessary screws

Sqm 175 1352.28 236649.00


30 French spirit polishing Two or more coats on new work including a coat of wood filler Sqm 225 121.10 27247.50

31 Providing and fixing anodised aluminium work for doors, windows ventilators and partitions with extruded built-up standard tubular and other sections of approved make conforming to IS:733 and IS:1285, anodised transparent or dyed to required shade according to IS:1868 (Minimum anodic coating of grade AC - 15), fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free straight, mitered and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws, all complete as per architectural drawings and directions of Engineer-in-charge. (Glazing & panelling to be paid for separately) For fixed portion

Kg 2000 494.56 989120.00

For openable/sliding portions and fixing hinges/pivots, PVC/neoprene gasket required and making provision for fixing of fittings. (Fittings shall be paid for separately) Kg 1500 514.02 771030.00

32 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) With float/frosted glass panes of 4mm thikness (weight not less than 10.0 kg/sqm)

Sqm 320 907.36 290355.20

33 Supplying, providing and fixing white colour sliding uPVC Door complete, consisting of uPVC frame of size 95mmx60m m and uPVC shutter of size 66mmx42mm with 1.2mm thick GI section reinforcement wherever required, produced by ISO 9001:2000 and ISO 14001:2004 certified company. Door shutter will consist either of 5mm thick float glass or galvanised wire gauge or solid PVC panel alongwith complete fittings, e.g. pulley/rollers, transmission gear and handle for operating door.

Sqm 32 7031.94 225022.08

34 Supplying and fixing rolling shutters of approved make as per IS:6248, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5cm long wire spring grade no. 2 and M.S. top cover of required thickness for rolling shutters : 80x1.25mm M.S. laths with 1.25mm thick top cover.

sqm 75 2470.18 185263.50

Providing and fixing ball bearing for rolling shutt ers. Each 10 447.40 4474.00


35 providing & fixing in position Collapsible steel shutters with vertical channels 20mmx10mmx2mm and braced with flat iron diagonals 20mmx5mm size with top and bottom rail of T-iron 40mmx40mmx6mm with 40mm dia. Steel pulleys complete with bolts, nuts, locking arrangement, stoppers,handles and hold fasts including applying a priming coat of approved steel primer.

sqm 10 3457.49 34574.90

36 Providing and fixing M.S. fan clamp of 16mm dia MS bar bent to shape with hooked ends in RCC slabs during laying including painting the exposed portion of loop, all as per standard design complete Each 95 108.40 10298.00

37 Steel work welded in built-up sections / farmed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladders, raillings, brakets, gates and similar works.

Kg 2550 100.50 256275.00

38 Providing and fixing hand rail by welding etc. to steel ladders railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. E.R.W. tubes 40mm nominal dia

Kg 90 137.98 12418.20

39 Providing and fixing MS round or square bars / flats or grills in frames in window and clerestory windows sqm 66 63.83 4212.78

40 Providing and fixing copper oxidised brass 100mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality) Each 82 906.79 74356.78

41 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws etc. complete (best make of approved quality) Single rubber stopper

Each 70 37.93 2655.10

42 Providing and fixing IS:3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete Hardwyn make (Eddy) or equivalent

Each 12 1481.86 17782.32

43 Providing and fixing Nickel chromium plated brass tower bolts (barrel type) with necessary screws etc. complete:200mm x 10mm

Each 70 189.29 13250.30


44 Providing and fixing at all hight false ceiling of 12mm thick tapered edge gypsum board conforming to IS:2095-Part I, including providing and fixing of frame work made of special section power pressed from M.S. sheet and galvanised with zinc coating of grade 350 as per IS:277 and consisting of angle cleats of size 25mm x 1.6mm long with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with stener 12mm dia x 40mm long with 6mm dia bolts to the angle hangers of 25mm x 25mm x 0.55mm of required length and other of angel hanger being fixed with nuts and bolts to G.I. chanels 45mm x 15mm x 0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall fixed in a direction perpendicular to

Sqm 110 733.85 80723.50

G.I. channel with connection slipd made out of 2.64mm dia x 230mm long gypsum board with seiling section and primeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long,the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive all screws @ 230mm interval including jointing square edges of the gypsum board with recommended filler,paper tapes,finisher and as per manufacturerers specification and also including the cost of making openings for light fittings,grills,diffucers, cutouts mace with frame of perimeter channels suitably fixed all complete as per drawing as per specification and direction of the Engineer-in-charge but excluding the cost of painting.

45 Structural steel work welded in built up sections, trusses and framed work , girders, stagings, racks, etc. including cutting, bending, straightening, hoisting, fixing in position including applying a priming coat of approved steel primer complete - upto 6m height above GL In RSJ, tees, angles and channels

Kg 450 100.34 45153.00

Erecting roof trusses including rivetting for work upto 10m height above GL quintal 45 226.26 10181.70

Extra over item no. 43 above for every subsequent 5 m height or part thereof over 10m height above GL quintal 45 56.57 2545.65

46 Providing and fixing 0.55mm TCT Standing Seam/clip lock profile for roofing comprising Zincalume / Galvalum e base steel of metal thickness 0.5mm and coated with Zinc-Aluminium coating of AZ-150 (150 gsm) as per AS:1397-1993 (total of both sides) and parmanently colour coated with 20 microns Super Polyester/SMP colour coating over a 5 micron primer and a back coat of 5 micron over a 5 micron primer. Standing Seam sheets to be profiled to desired length & width of 400mm to 770mm, having profile depth of 31mm to 61mm with a unique concealed clip made from GI, one portion of the clip (lower) fastened to purlin and upper part gets attached to roofing sheet. Thereby providing an absolutely puncture-less roof with concealed clip crimped / locked together by a mechanical sewing machine

Sqm 15 861.40 12921.00

Cost of Schedule - B 9176996.19


Schedule - B-I (Brick works)

1 Brick work with non-modular (FPS) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6t mortar 1:6 (1 cement : 6 fine sand)

Cum 750 2163.97 1622977.50

2 Extra over item no. 1 above for brick work in super structure beyond plinth level upto floor two level. cum 685 151.99 104113.15

3 Extra for brickwork in superstructure beyond second floor level for every 3m or part thereof cum 85 287.47 24434.95

4 Half brick masonry with bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Sqm 225 265.31 59694.75

5 Extra for half brick masonry in superstructure abov e plinth level upto floor two level Sqm 225 42.15 9483.75

Cost of Schedule - B-I 1820704.10

Schedule - B-II (Concrete & Shuttering works)

1 Providing and laying Plain Cement Concrete up to plinth in retaining walls, walls (any thickness) including attached plasters, columns, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets etc, excluding the cost of cement and of shuttering, centering. 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size)

cum 182 2325.34 423211.88

2 Providing and laying in position M25 grade concrete for reinforced concrete structural elements but excluding cost of centering, shuttering, reinforcement, cement and Admixtures in recommended proportion (as per IS:9103) to accelarate, retard setting of concrete, Improve workability without impairing strength and durability as per direction of Engineer in charge i) For Pile Cap, Tie beam, Pedestal etc.

cum 425 2732.49 1161308.25

ii) All works upto Plinth level Cum 179 2732.49 489115.71

iii) All works in buildings above plinth level upto floor two level cum 670 3004.22 2012827.40

iv) Extra for RCC work in superstructure above floo r two level for every floor or part thereof cum 60 316.54 18992.40


3 Supplying & mixing high range poly carboxylate ether base water reducing admixture Plast Super-C700 conforming to IS:9103-1999 (to be added @1% by weight of cement) for CC & RCC work for controlling water cement ratio and for gaining early strength

Kg 11000 77.03 847330.00

4 Centering and shuttering including strutting, propping etc. and removal of form work for Fundations, footings, bases of columns,

Sqm 425 146.28 62169.00

5 Centering and shuttering including strutting, propping etc. and removal of form for Pile caps,Tie beam, plinth beam, column, Pedestal h beam, column, Pedestal etc.

Sqm 2474 145.90 360956.60

Suspended floors, roofs, landings, balconies, FOB s labs, walkway slabs and access platform Sqm 440 234.36 103118.40

Lintels, beams, plinth beams, bed blocks, girders, cantilevers etc. Sqm 1650 208.55 344107.50

Columns, pillars etc. Sqm 1400 297.00 415800.00

Stairs (excluding landings) except spiral staircase s Sqm 380 289.10 109858.00

6 Centering and shuttering including strutting, propping etc. and removal of form for

Walls (any thickness) including attached plasters, buttresses, plinth and string courses etc.

Sqm 300 239.00 71700.00

6 Extra for additional height in centering, shuttering wherever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m for every additional height of 1 metre or part there of in suspended floors, roofs, landing, beams and balconies (plan area to be measured)

Sqm 3850 92.10 354585.00

7 Supplying & applying shuttering oil for mould releasing,having (flash point 54 degree C and specific gravity 0.88±0.02) for concrete formwork to be applied either brush or with spray machine to the entire satisfaction Engineer incharge.

Sqm 7033 6.43 45222.19

Cost of Schedule - B-II 6820302.33

Schedule - B-III (Supply of Reinforcement Steel)

1 Supplying reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete l complete Thermo-Mechanically Treated bars

Kg 220000 69.36 15259200.00


Cost of Schedule - B-III 15259200.00

Schedule - B-IV (Supply of Cement)

1 Ordinary Portland Cement Grade-43 / Portland Slag C ement MT 1181 7302.50 8624252.50

Cost of Schedule - B-IV 8624252.50

Schedule - B-V (Plumbing & Sanitary works)

1 Providing and fixing on wall face unplasticised Rigid PVC single socketed rain water pipes conforming to IS:13592 Type-A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion 110mm dia.

Metre 150 232.69 34903.50

2 Providing and fixing on wall face unplasticised PVC moulded fittings /accessories for unplasticised - Rigid PVC rain water pipes conforming to IS:13592 Type-A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion Coupler, 110mm

Each 55 204.64 11255.20

Single tee with door, 110mm x 110mm x 110mm Each 35 393.77 13781.95

3 Providing and fixing on wall face unplasticised PVC moulded bend and shoe for unplasticised-Rigid PVC rain water pipes conforming to IS:13592 Type-A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion shoe (Plain), Shoe (Plain) 110mm dia. shoe

Each 50 283.77 14188.50

4 Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete 110mm

Each 100 127.22 12722.00

5 Providing and fixing white, vitreous china water closet squatting pan (Indian type) Long pattern W.C. pan of size 580mm Each 6 792.18 4753.08

6 Providing and fixing a pair of white, vitreous china foot rests of standard pattern for squatting pan water closet or in urinals: 250mm x 130mm x 30mm Pair 10 237.81 2378.10


7 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litres low level white vitreous china flushing cistern and C.P flush bend with fittings & C.I./M.S. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito-proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors, wherever required : W.C. pan with ISI marked white solid plastic seat and lid.

Each 25 4263.34 106583.50

8 Providing and fixing white, vitreous china flat back half stall urinal of 580mm x 380mm x 350mm with white P.V.C. automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS:2556, C.I. trap with outlet grating and other coupling in C.P. brass including painting of fittings and cutting and making good the walls and floors, wherever required : Range of two half stall urinals with 5 litres P.V.C. automatic flushing cistern.

Each 15 7359.21 110388.15

9 Supplying and fixing marble stone 20mm to 25mm thic k in masonry or concrete as a purdha to urinal range etc. Stone to be machine cut and well polished on all faces and the edges to be moulded by semi circular rounding & polishing. Marble shall be any one of the following: Makrana Chalk Doongri

sqm 12 1802.13 21625.56

10 Providing and fixing white, vitreous china squatting plate urinal with integral longitudinal flush pipe Each 6 1280.44 7682.64

11 Providing and fixing wash basin with C.I./M.S. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls, wherever required : White, vitreous china wash basin size 630mm x 450mm with a pair of 15mm C.P. brass pillar taps.

Each 25 1993.27 49831.75

12 Providing and fixing white, vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. Each 25 1110.13 27753.25

13 Providing and fixing PTMT Bottle Trap for Wash basin and sink : Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 250mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 270gm.

Each 25 476.99 11924.75

14 Providing and fixing PVC connector 15mm size with non-corrosive PTMT couplings in both ends 15mm dia. 450mm long. Each 25 77.12 1928.00

15 Providing and fixing Stainless Steel AISI-304 (18/8) kitchen sink with drain board as per IS:13983 with C.I. brackets and stainless stel plug 40mm including painting of fittings and brackets, cuting and making good the walls, wherever required : 510mm x 1040mm bowl depth 250mm

Each 5 6262.30 31311.50


16 Providing and fixing 600mm x 450mm bevelled edge mirror , 5.5mm thick of float glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Each 20 850.23 17004.60

17 Providing and fixing 600mmx120mmx5mm glass shelf with edges round or supported on anodised aluminium angle frame with c.p. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs etc. complete

Each 20 480.17 9603.40

18 Providing and fixing Towel rail (C.P.) brass 15mm dia x 600mm long having approx. weight 500gm Each 20 350.48 7009.60

19 Providing and fixing Soap dish (C.P. Brass) having approx. weight 220 gm Each 20 157.28 3145.60

20 Providing and fixing Liquid soap container (C.P. Brass) having approx weight 240 gm.

Each 20 189.08 3781.60

21 Providing and fixing C.P. brass grating with openable lid : Grating 100mm nominal dia and 12mm high domed shape having weight not less than 25 gm Each 20 123.82 2476.40

22 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete : flexible pipe 32mm dia.

Each 25 78.20 1955.00

23 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete : Semi-rigid pipe 32mm dia. Each 25 55.75 1393.75

24 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors : 100mm inlet and 100mm outiet sand cast iron S&S as per IS:1729

Each 25 851.02 21275.50

25 Providing and fixing Toilet paper holder (C.P. Brass) having approx. weight 250 gm

Each 22 240.18 5283.96

26 Providing and fixing Coat hook 'J' type two way (C.P. Brass) Each 11 101.14 1112.54

27 Supplying and fixing half round white glazed earthen ware drains 100mm dia. With cement sand mortar 1:3 mix and joints grouted with neat cement slurry of the matching colour : M 50 186.20 9310.00


28 Providing and fixing soil, waste and vent pipes 100mm dia. Centrifugally cast (spun) iron S & S pipe as per IS:3989 metre 125 701.93 87741.25

29 Providing and fixing soil, waste and vent pipes 75mm dia . Centrifugally cast (spun) iron S & S pipe as per IS:3989 metre 150 599.50 89925.00

30 Providing and fixing M.S. holder-bat clamps of approved design to sand cast iron/cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. for 100mm dia. pipe

Each 35 105.82 3703.70

31 Providing and fixing M.S. holder-bat clamps of approved design to sand cast iron/cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. for 75mm dia. pipe

Each 70 101.39 7097.30

32 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diamet er 100mm Each 60 75.25 4515.00

33 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter 75mm Each 70 65.15 4560.50

34 Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete 100mm dia. Sand cast iron S&S as per IS-3989 Each 40 490.15 19606.00

35 Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete 75mm dia. Sand cast iron S&S as per IS-3989 Each 70 354.12 24788.40

36 Providing and fixing plain bend of required degree 100mm dia. Sand cast iron S&S as per IS-3989 Each 50 400.52 20026.00

37 Providing and fixing plain bend of required degree 75mm dia. Sand cast iron S&S as per IS-3989 Each 20 327.66 6553.20

38 Painting two or more coats on, sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate, grey or buff etc. over a coat of primer (of approved quality) to give an even shade for new work 100mm diameter pipe

metre 170 25.87 4397.90


39 Painting two or more coats on, sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate, grey or buff etc. over a coat of primer (of approved quality) to give an even shade for new work Upto 75mm diameter pipe

metre 250 19.71 4927.50

40 Providing & fixing single equal plain junction of required degree with access door, insertion rubber wash 3mm thick, bolts and nuts complete : 100mm x 100mm x 100mm sand cast iron S&S as per IS-3989

Each 40 641.67 25666.80

41 Providing & fixing single equal plain junction of required degree with access door, insertion rubber wash 3mm thick, bolts and nuts complete : 75mm x 75mm x 75mm sand cast iron S&S as per IS-3989

Each 40 473.65 18946.00

42 Providing and fixing 8cm dia. PVC plain bend of the required degree including jointing and cost of spun yarn and sand etc. complete. Each 40 181.46 7258.40

Providing and fixing terminal guard : 100mm sand cast iron S&S as per IS-3989 Each 40 337.32 13492.80

43

Providing and fixing terminal guard : 75mm sand cast iron S&S as per IS-3989 Each 40 257.68 10307.20

44 Providing and fixing 110mm PVC offset including jointing and cost of squn yarn and sand etc. complete : with 15cm projection Each 20 216.31 4326.20

45 Supplying, fixing and fittings cowls to vent pipes : Wire cowls for pipes of size 50/75 mm dia. Each 20 103.18 2063.60

46 Providing and fixing brackets comprising of aluminium painted standard steel clip and cast iron base for 110mm pipes, including cost of screws etc. and drilling of holes and making good the walls including cost of sand etc. complete.

Each 100 82.54 8254.00

47 Providing and fixing 110x110x110mm dia. PVC plain branch (single equal junction) of the required degree including jointing and the cost of spun yarn and sand etc. complete. Each 30 134.77 4043.10

48 Providing, laying and jointing glazed stoneware pipes grade 'A' as per IS:651 including bends etc. with stiff mixture of cement mortar in the proportion of 1:1 (1cement : 1 fine sand) including testing of joints etc. complete : 300mm diameter

M 130 889.98 115697.40

230mm diameter M 85 539.49 45856.65


49 Providing and fixing square-mouth S.W. gully trap grade 'A' complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300mm size (inside) the weight of cover to be not less than 4.50kg and frame to be not less than 2.70kg as per standard design : 150x100mm size 'P' type with F.P.S. bricks class designation 7.5

Each 10 1266.81 12668.10

50 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes including bends etc with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete upto 800mm dia : 300mm dia. R.C.C. pipe.

M 40 483.44 19337.60

250mm dia R.C.C pipe M 285 382.87 109117.95

51 Supplying, fitting & fixing in position reinforced cement polymer concrete (RCPC) manhole cover and frame to match with IS:12592 with cement concrete 1:2:4 for embedding the manhole cover frame: 25 MT load bearing capacity manhole cover provided with 2 nos. lifter lock fitted with matching frame (size of cover : 630mm dia x 100mm thick and size of frame: 790mm dia x 185mm thick)

Each 35 1714.61 60011.35

52 Constructing brick masonry road gully chamber 50cm x 45cm x 60cm with bricks of class designation 7.5 in cement mortar 1:4 including 500mm x 450mm precast RCC horizontal grating with frame complete as per standard design 1:4 including 500mm x 450mm precast RCC horizontal grating with frame complete as per standard design With FPS bricks

Each 15 2326.89 34903.35

53 Constructing brick masonry mahhole in cement mortar 1:4 (1 cement : 4 coarse sand) R.C.C. top slab with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90cm x 80cm and 45cm deep including C.I. cover with frame (light duty) 455mm x 610mm internal dimensions total weight of cover and frame to be not less than 38kg (weight of cover 23kg and weight of frame 15 kg) with F.P.S. bricks class designation 7.5

Each 5 4673.34 23366.70


54 Constructing grease trap 80x40x46cm (inside) with one brick thick brick masonry wall with inlet and outlet drain with bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 fine sand) plastered 12mm thick with 1:4 (1 cement : 4 coarse sand) finished with a floating coat of neat cement on inside and exposed surfaces having two stone/RCC baffied walls 34.5cm deep and third one 19cm deep, each 40mm thick and 45cm long embedded 2.5cm on either side in brick masonry, 40mm thick 100x60cm stone/RCC cover and 7.5cm thick bed concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) with 40mm flooring in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size) with a floating coat of neat cement including all earth excavation, refilling and disposal of surplus earth complete as per standard design : with F.P.S. bricks

Each 3 1557.77 4673.31

55 Making soak pit 2.5m diameter, 3m deep with 45x45cm dry brick honey comb shaft with bricks of class designation 7.5 and S.W. drain pipes 100mm diameter, 1.8m long complete as per standard design, including excavation complete : with F.P.S. bricks

Each 3 12619.61 37858.83

56 Supplying, fitting & fixing in position reinforced cement polymer concrete (RCPC) manhole cover and frame to match with IS:12592 with cement concrete 1:2:4 for embedding the manhole cover frame: 3 MT load bearing capacity manhole cover provided with 2 nos. lifter lock fitted with matching frame ( size of cover: 440mm dia x 50mm thick and size of frame:750mm dia x 150mm thick)

Each 8 1232.99 9863.92

Providing and fixing medium grade G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the wall etc. : Concealed pipe including painting with anti-corrosive bitumestic paint, cutting chase and making good the wall 15mm dia. nominal bore

M 870 195.86 170398.20

57

20mm dia. nominal bore M 305 242.17 73861.85

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall s etc. Internal work - Exposed on wall 25mm dia. Nominal bore

M 150 292.33 43849.50

40mm dia. Nominal bore M 175 355.79 62263.25


58



Making connection of medium grade G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete ution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete 50mm to 80mm nominal bore.

Each 18 609.47 10970.46

59

25mm to 40mm nominal bore. Each 120 247.60 29712.00

60 Providing and fixing PP-R Brass Ball Valve fusion welded, having thermal stability for hot & cold water supply and testing of joints complete as per direction of engineer in charge 20mm Ball Valve. Each 38 761.73 28945.74

61 Providing and fixing PP-R Gate Valve fusion welded, having thermal stability for hot & cold water supply and testing of joints complete as per direction of engineer in charge 25mm Gate Valve

Each 6 575.20 3451.20

62 Providing and fixing PP-R Male adopter conforming to PN-25 rating with marking on each fitting, fusion welded, having thermal stability for hot & cold water supply and testing of joints complete as per direction of engineer in charge 20mm adopter for PPR-GI connection.

Each 70 227.39 15917.30

63 Providing and fixing gun metal non-return valve of 80mm nominal bore approved quality (screwed end) : vertical Each 2 5759.88 11519.76

64 Providing and fixing gun metal non-return valve of 40mm nominal bore approved quality (screwed end) :vertical Each 8 1683.36 13466.88

65 Providing and fixing C.P. brass bib cock , 15mm nominal bore of approved quality conforming to IS:8931 Each 110 469.88 51686.80

66 Providing and fixing C.P brass long nose bib cock , 15mm nominal bore, of approved quality conforming to IS standards and weighing not less than 810gm

Each 25 464.19 11604.75

67 Providing and fixing C.P brass stop cock , 15mm nominal bore, (concealed) of standard design and of approved quality conforming to IS:8931

Each 140 404.48 56627.20

68 Polyethylene Vinyl Chloride water storage tank with cover and suitable locking arrangement litre 10000 8.63 86300.00

69 Hoisting, fitting and fixing in position plastic moulded water storage tank including making connection of intake, delivery, outlet and overflow pipes etc. with all lead & lift upto all stories. (cost of tanks/fittings to be paid separately) 2500 litre capacity tank

Each 4 1701.31 6805.24

Cost of Schedule - B-V 2143860.87


Schedule - C (Supply & Installation of Modular Work station)

Supplying, providing and fixing Running Counter/Workstation made of 19mm BWR block board with low height partition having lamination on it. The size of each table will be 600mm depth x 750mm height x 1500mm length having 1 no. pedestal with 1 no. drawer and 1 no. cup board with keyboard tray. All edges of the board should be properly beading with 5mm thick teak wood. The below portion of the BWR ply should be painted with enamel paint. All exposed wooden beading should be french polishing. In addition with that supplying, providing and fitting of 62mm thick wooden partition (1200 mm height) made of 50 x 50mm Sal wood frame with a span of 600mm vertically and horizontally. Fixing BWR 6mm ply on both side finished with laminate including all other necessary fitting and fixing complete. Supplying and fixing 12mm soft board above 900mm height from ground level cover with approved colour and make cloth with all other necessary fittings and fixing complete.

1

All wood leaping should be teak wood and all exposed wooden portion should be polished.Providing & fixing electrical circuit from DB to switch board with 2.5mm multi core cable with 1.5mm proper earthing; supply & fixing of switch board with 1.5mm cable, providing & fixing of 15 AMP. switch of Anchor make with fuse; supplying & fixing of 5 pin, 5 AMP. Socket of Anchor make and supplying & fixing of 2 x 4 Tube light, mirror optic fittings with tube including all necessary fitting and fixing complete

Each set

40 25192.88 1007715.20

Cost of Schedule - C 1007715.20

Schedule - D (Supply & Installation of FRP Water st orage tank including water pipeline & fire water pi peline network)

1 Supplying, fabricating, erecting, fitting, fixing in position of GRP/SMC panelled water storage tank (Binani make or it's eq uivalent), having storage capacity 1,12,000 litre, size : 8m x 7m x 2m on a 16m height staging as per IS: 14399 . The rates includes all fasteners, UPVC inside support, ladder, HDG outside bracing, FRP manhole cover, PVC ventilator complete in all r espect . The tank should have factory fitted provision for inlet, outlet, overflow, wash pipe line and provision for one additional delivery pipe line for future use of dia as specified by engineer at site. The work complete in all respect with contractor's tools, plants, lab our, material, scaffolding and removing the same after completion of work . The contractor has to submit 10 years guarranty certificate against any leakage, manufacturing defects etc.

KL 112 11500.00 1288000.00

2 Structural steel work welded in built up sections, trusses and framed work, girders, stagings , racks, etc. including cutting, bending, straightening, hoisting, fixing in position including applying a priming coat of approved steel primer complete - upto 16m height above GL built up sections, trusses and framed work, girders, stagings, racks, etc. including cutting, bending, straightening, hoisting, fixing in position including applying a priming coat of approved steel primer complete -

Kg 40000 100.34 4013600.00


upto 16m height above GL In RSJ, tees, angles and channels

Providing and laying S&S centrifugally cast (Spun) Ductile Iron pipes conforming to IS:8329 of class K-7 upto 500mm dia.

3

100mm dia. Ductile Iron Class K-7 pipes metre 450 941.65 423742.50

4 Providing and fixing medium grade G.I. pipes complete with G.I. fittings including trenching and refilling etc. ; External work

25mm dia. Nominal bore metre 80 236.37 18909.60



5 Providing and fixing gun metal non-return valve of 80mm nominal bore approved quality (screwed end) : vertical

Each 4 5759.88 23039.52

Providing & Laying S&S C.I. standard specials,e.g. tees, bends, collars, tapers caps etc. (Heavy class)

6

Upto 300mm dia Qtl. 8 6669.09 53352.72

Supplying and jointing-in-position cast iron flanged, end foot valve with strainer (of cast iron/galvanized iron) swing type tested to withstand a pressure of 2kg/sqcm. Complete in all respects, conforming to IS: 4038

7

80mm size Each 20 1266.57 25331.40

Total Cost of Schedule-D 6002614.76

Schedule - E (Deep Tubewell work)

1 Drilling and boring hole of sinking of 300×200mm dia by using hydraullic rotary drilling machine either direct or reverse circulating method in any kind of soil upto required depth by using 600mm dia drill bit as per IS:2800(PT. I & II) of 1979 including cost of cutting mud and mud pit. The rate includes supply of all tools and plants required to complete the work in all respect.

M 300 1150.00 345000.00

2 Supplying 300mm dia PVC pipe of '80 SCHEDULE' having wall thickness 18mm of "ori-plast" or any other approved brand confirming to ASTMD-1785

M 50 4200.00 210000.00


3 Supplying 200mm dia PVC pipe of '80 SCHEDULE' having wall thickness 12.7mm of "ori-plast" or any other approved brand confirming to ASTMD-1785

M 250 2100.00 525000.00

4 Supply of 200mm dia reinforced glass fibre strainer 6mm thick PIONEER or VMT make or approved brand.

M 30 3050.00 91500.00

5 Fitting, fixing,jointing and lowering the tube well assemble inside the bore hole including supply of centre guide. M 300 120.00 36000.00

6 Gravel packing in annular space of bore hole of the tube well assemble upto housing pipe including supply of pea gravel (2mm-5mm) size. Gravel should be washed before use. cum 40 1200.00 48000.00

7 Supplying following PVC accessories and specials for tube well assemble- a) Top cap 300mm dia-1no. b) Reducer 300×200mm dia- 1no. C) Tail plug 200mm dia- 1no. SET 1 9000.00 9000.00

8 Geophysical investigation of acquifer by electro logging method. The rate includes hire charges of tools and plants required for the execution of the work. Each 1 10000.00 10000.00

Total of Schedule-E 1274500.00

Schedule - F (Any other unforseen items)

1 Any other unforseen item which is not covered under the above schedule of works will be executed from Unifi ed Standard Schedule of Rates/Eastern Railway-2011 ( B asic Cost:- Rs. 10,00,000/-)

LS LS At Par 1000000.00

Total of Schedule-F 1000000.00

Schedule - G (Internal Electrification including su pply, installation & commissioning of 6 passengers Lift)

Unit rate Amt Sl

No Description of item Unit Qty

( Rs) in Rs 01 Supply & wiring of concealed light / fan/call bell/ 5 amps socket points No 724 302.70 219154.80


02 Supply & concealed wiring by 4 sq. mm single core copper cable for 5/15 amps socket points & submain wire from DB to individual switch board

Rmt 2670 55.03 146930.10

03 Supply & concealed wiring for submain from Main DB to Sub DB by 6 Sqmm single core copper cable

Rmt 240 99.00 23760.00


Rmt 210 210.32 44167.20


Rmt 40 316.92 12676.80

06 Supply, fixing & commissioning of 6 pin, 5/15 amps sockets. No 69 121.00 8349.00

07 Supply, fixing & commissioning of 1 X 28 W T- 5 Box type FL fittings No. 176 609.00 107184.00

08 Supply, fixing & commissioning of 2 X 28 W T- 5 Box type FL fittings No 50 1606.00 80300.00

09 Supply, fixing & commissioning of decorative 2 X 28 W T- 5 Miror optics FL fittings

No 68 2740.00 186320.00

10 Supply, fixing & commissioning of CFL fitting with 11W lamp No 62 225.00 13950.00

11 Supply, fixing & commissioning of Bulk Head fitting with 11W CFL lamp

No 5 1586.00 7930.00

12 Supply, fixing of Call bell No 22 287.00 6314.00

13 Supply, fixing of 1400 mm sweep, ceiling fan No 101 1606.00 162206.00

14 Supply, fixing of stepped type electronic fan regulator No 101 150.00 15150.00

15 Supply & fixing of Wall bracket fan 400 mm sweep

No. 49 2355.00 115395.00

16 Supply & fixing of 300mm sweep exhaust fan No 33 1412.48 46611.84

17 Supply, fixing & commissioning of computer board No 60 118.70 7122.00


18 Supply, fixing & commissioning of SPN DB DD 12 way with one DPMCB, 40 amps & 10 SPMCB, 6 amps

Set 15 11224.04 168360.60

19 Supply, fixing & commissioning of TPN DB DD 4 way with one FPMCB, 80 amps & 8 SPMCB, 25 amps

Set 2 14847.36 29694.72

20 Supply, fixing & commissioning of TPN DB DD 4 way with one FPMCB, 125amps, 8 SPMCB, 25 amps & 4 SPMCB 32 apms

Set 1 9154.93 9154.93

21 Supply, fixing & commissioning of cubical LT panel containing one FPMCB, 125amps, busber 200 amps & 3 FPMCB, 80 amps

Set 1 42260.78 42260.78

22 Supply & laying of LT PVC/XLPE armoured aluminium 1100V grade cable of size 3.5 core 35 sq mm

RMT 50 260.69 13034.50

23 Supply, erection , testing & commissioning of submersable pupm set 25 HP complete

Set 1 314584.00 314584.00

24 Supply, installation, testing & commissioning of electrically driven main fire pump suitable for automatic operation

set 1 403652.46 403652.46

25 Supply, installation, testing & commissioning of diesel engine driven main fire pump suitable for automatic operation .

set 1 806892.13 806892.13

26 Supply, installation, testing & commissioning of Electrically driven jockey fire pump suitable for automatic operation .

set 1 54542.68 54542.68

27 Supply, installation, testing & commissioning of main circuit control panel in fire control room against fire fighting

Set 1 117000.00 117000.00

28 Supply, fixing, testing and commissioning of double flanged sluice valve. 0.00

(a) 100 mm dia No 2 9700.00 19400.00

(b) 150 mm dia No 2 12850.00 25700.00

( c) 80 mm dia No 1 8100.00 8100.00 29 Supply, fixing, testing and commissioning of butter fly valve. 0.00

(a) 200 mm dia No 7 9700.00 67900.00 (b) 100 mm dia No 2 5300.00 10600.00 ( c) 80 mm dia No 5 3000.00 15000.00


(d) 65 mm dia No 1 2650.00 2650.00

30

Supply, Installation, testing and commissioning of stainless steel stainer 200 mm dia

No 1 2900.00 2900.00

31

Supply, Installation, testing and commissioning of Ball valve.

31a 25 NB No 11 1300.00 14300.00

31b 50 NB No 3 3300.00 9900.00

32

Supply, installation, testing and commissioning of presure gauge No 4 1500.00 6000.00

33

Supply, installation, testing and commissioning of presure vacuum gauge No 1 2000.00 2000.00

34

Supply , Installation, testing and commissioning of non return valve. No

34 a

150 mm dia No 3 8100.00 24300.00

34b 65 mm dia No 1 4100.00 4100.00

34c 100 mm dia No 1 5500.00 5500.00

35

Design, supply and fixing of hydro pneumatic tank No 1 26000.00 26000.00

36

Supply, installation & testing of air release valve. No 2 2100.00 4200.00

37

Supply & fixing of pressure switch ( Normal type ) . No 2 3200.00 6400.00

38

Supply & fixing of pressure switch ( Differential type ) . No 1 3700.00 3700.00

39

Design, supply and installation of diesel tank No 1 14500.00 14500.00

40

Supplying and fixing of single headed external yard hydrant valve No 3 12000.00 36000.00

41

Supply & fixing of single headed internal hydrant valve No 6 8000.00 48000.00

42

Protection for hydrants provided in the paved area after supplying the required material

No 2 7000.00 14000.00

43

Supply, laying, testing & commissioning of MS pipe.

43a 200 mm dia Mtrs 15 3500.00 52500.00

43b 150 mm dia Mtrs 30 2600.00 78000.00

43c 100 mm dia Mtrs 150 1600.00 240000.00

43d 80 mm dia Mtrs 50 1150.00 57500.00

43e 50 mm dia Mtrs 10 900.00 9000.00

43f 25 mm dis Mtrs 30 650.00 19500.00

44 Laying of MS pipes of various sizes Mtrs 40 800.00 32000.00

45

Supplying and fixing of MS pedestal mounted type hose boxes No 6 2200.00 13200.00


46

Supply of reinforced rubber lined hose with gun metal coupling of dia 63 mm

No 6 5200.00 31200.00

47 Supply of Gun metal branch pipe. No 6 1650.00 9900.00

48

Supply, installation & testing of Small Bore Hose reel No 6 5600.00 33600.00

49

Supply and fixing of 4 way fire brigade connection . No 1 9200.00 9200.00

50

Supply. Installation, testing and commissioning of addressable Fire detection and alarm panel

No 1 127000.00 127000.00

51

Supply installation testing and commissioning of Analogue addressable heat detector with transmitter, receiver and power supply

No 36 900.00 32400.00

52 Addressable manual call point No 6 1600.00 9600.00

53 Addressable loop powered sounder No 5 2200.00 11000.00

54

Supply and laying of FRLS, PVC insulated sheathed armoured multistrand shielded copper cables, 2 X 1.5 sq. mm

Mtrs 400 130.00 52000.00

55

Supply,fixing, testing and commissioning of dual chamber, dual source ionization type smoke detector with base and hardware

No 6 2600.00 15600.00

56

Supply, fixing testing and commissioning of optical smoke detector with base and hardware for mounting

No 6 2600.00 15600.00

57

Charges for preperation of drawings plan and other documents LS 1 160000.00 160000.00

58

Design, drawing, supply, erection, testing & commissioning of autometic monospace 6 passenger elevator.

No 1 1448005.00 1448005.00

59

In service comprehensive maintenance contact of elevator for a period of 2 year after warrenty period of 1 year

No 1 100000.00 100000.00

60

Supply & erection of GI pipe earthing complete Set 46 1652.00 75992.00

61

Supply & laying of 63 mm inner dia, 3.5 mm wall thichness PVC pipe for cable protection

mt 50 168.94 8447.00

62

Supply, installation, testing & commissioning of water cooler Set 3 38018.82 114056.46

63

Supply, errection, testing & commissioning of 2 Tone split Air conditioner

Set 8 36043.00 288344.00

64

Supply & erection of main LT control panel Set 1 147059.94 147059.94


65

Supply & erection of sub LT control panel for Adminstrative building Set 1 115046.00 115046.00

66 Supply & erection of sub isolator for lift Set 1 12863.39 12863.39

Total of Schedule - G 6852461.33

Total Cost of Schedule - A + B + B-I + B-II + B-III + B-IV + B-V + C + D + E + F + G 66859531.58

Say 66859532.00

Rupees Six Crore Sixty Eight Lakh Fifty Nine Thousa nd Five Hundred Thirty Two Only

RITES · PDF fileRITES LTD. OPEN TENDER ... working load not less than specified incl. cost...

Documents

Transcript of RITES · PDF fileRITES LTD. OPEN TENDER ... working load not less than specified incl. cost...