Rhino-Rack Luggage Box Wall Hanger...
4
Rhino-Rack Luggage Box Wall Hanger (RWHMF) Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies. Keep these instructions in the vehicle’s glove box after installation is complete for future reference. Important Information When selecting a suitable wall to mount this hanger, ensure the wall has enough strength to support the luggage box. Always fix to wall studs or use appropriate concrete/ brick inserts. Do not fix to dry wall only. Wall Mount is designed for indoor use only. Always support luggage box with both hangers supplied in this kit. Recommendations Do not climb or hang from the storage racks. It is only intended to store luggage boxes only. Load Ratings The Wall Hanger’s load capacity is 30kg. Ensure that appropriate fasteners are used to suit the wall type (i.e. brick wall, plasterboard, wood, etc) Note for Dealers and Fitters It is your responsibility to ensure that this fitting instruction is given to the end user or client. Rhino-Rack 3 Pike Street, Rydalmere, NSW 2116, Australia. Document No: R417 (Ph) (02) 9638 4744 Prepared By: Kayle Everett Issue No: 02 (Fax) (02) 9638 4822 Authorised By: Chris Murty Issue Date: 24/06/2014 These instructions remain the property of Rhino-Rack Australia Pty Ltd and may not be used or changed for any other purpose than intended. Layout Page 1 of 4
Transcript of Rhino-Rack Luggage Box Wall Hanger...
Rhino-Rack Luggage Box Wall Hanger (RWHMF) Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies. Keep these instructions in the vehicle’s glove box after installation is complete for future reference.
Important Information
When selecting a suitable wall to mount this hanger, ensure the wall has enough strength to support the luggage box. Always fix to wall studs or use appropriate concrete/ brick inserts. Do not fix to dry wall only.
Wall Mount is designed for indoor use only. Always support luggage box with both hangers supplied in this kit.
RecommendationsDo not climb or hang from the storage racks. It is only intended to store luggage boxes only.
Load RatingsThe Wall Hanger’s load capacity is 30kg. Ensure that appropriate fasteners are used to suit the wall type (i.e. brick wall, plasterboard, wood, etc)
Note for Dealers and FittersIt is your responsibility to ensure that this fitting instruction is given to the end user or client.
Rhino-Rack3 Pike Street, Rydalmere, NSW 2116, Australia. Document No: R417 (Ph) (02) 9638 4744 Prepared By: Kayle Everett Issue No: 02(Fax) (02) 9638 4822 Authorised By: Chris Murty Issue Date: 24/06/2014
These instructions remain the property of Rhino-Rack Australia Pty Ltd and may not be used or changed for any other purpose than intended.
Layout
Page 1 of 4
Rhino-Rack Luggage Box Wall Mount (RWHMF)
Page 2 of 4
Tools Required: Tape measure, pencil/ pen, level, power drill (optional depending on wall type)
Item Component Name Qty Part No.
1 Upright Padded Arm 2 SP1392 Lower Padded Support 2 SP1403 Turn Wheel 2 SP1414 M6 Bolt, Washer and Nut 2 SP1425 Wall Bracket 2 SP1436 Wall Bracket Support 2 SP1447 Instruction 1 R417
Parts List
1. 2.
3.
Instructions1 To get the correct distance that will be used as a measurement between both wall mounted hangers, measure
the total length of your luggage box (x). Divide the distance (x) to find the correct spacing that should be used between your hangers (Y).
Top View
X/2=Y
4.
5.
6.
(X)
(Y)
Rhino-Rack Luggage Box Wall Mount (RWHMF) Rhino-Rack Luggage Box Wall Mount (RWHMF)
Page 3 of 4
Fitting Instruction
Mark the two holes that will serve as a reference point for dimension (Y). Note : These will be the two inner holes when both mounting brackets are in position on the wall.
3 Place item 2 onto the intended mounting surface. If mounting to timber walls, item 2 should be attached to wall studs.
Place item 2 against the intended mounting surface.
front view
Make sure item 2 is straight with a level.
4 5 Using the marks made in the previous step. Measure out the distance obtained in step 1 (y), place item 2 against the wall and mark as shown. Use a level to check item 2 is straight.
front view
2 Assemble the main body of the wall hanger. Place the Lower Padded Body inside the Wall Support Bracket. Fix in place with the Wall Bracket Supports, M6 Bolts and nuts. The Lower Padded Body’s locking pin will need to be pressed to allow it to fit into place when slideing in.
(Y)
(Y)
Rhino-Rack Luggage Box Wall Mount (RWHMF)
Page 4 of 4
7 Insert item 1 into item 2 as shown. Use item 3 to fix item 1 into place. Do not over tighten as adjustment may be needed at a later stage.
8 Place your luggage box onto the wall mounts. Adjust the mounts as required to fit. Place your luggage box onto the wall mounts so the weight is evenly distributed.Note: Ensure luggage box is emptybefore placing on wall mounts.
Adjust to length and tighten as required.
9 When not in use the mounts can be collapsed to remove any obstruction. Press in the locking spring pin and swing the arm against the wall.
Top View
Press the locking spring pin to free the arm.
Using appropriate hardware for the mounting surface. Attach both units.
Disclaimer: The user/ installer assumes total responsibility for the proper installation and use of this product. Rhino -Rack will not be held liable for damages or injuries resulting from the installation and/ or use of this product. If the installer is unsure of the requirements, he/ she should contact the company from which it was purchased.
6
1. 2.
3.
(Y)
