Revive Your Antique Pinfire Handguns

Revive your antique pinfire handgunsKITS PRICE LIST : http://hlebooks.com/pinfire/prices.htm

7mm Belgian made pinfire revolver

Vintage pinfire cartridgesLeft : 7mm - Right 9mm

PDF créé avec la version d'essai pdfFactory www.gs2i.fr/fineprint/pdffactory.htm

http://hlebooks.com/pinfire/prices.htm

http://www.gs2i.fr/fineprint/pdffactory.htm


To revive vintage pinfire handguns today is not a simple matter. Of sure, you will find here and there some vintage pinfire cartridges made about 100 years ago at prices in accordance with their rarity (sometimes $50 a piece), but it is not certain - to say the least - that the old primer mixture will again ignite the powder when crushing the pin.

11/12mm reloading kit is AVAILABLE

KITS PRICE LIST : http://hlebooks.com/pinfire/prices.htm





Reloading kit for pinfire cartridges (7mm, 9mm & 11mm)

9mm pinfire basic kitContent (packed in wood box) : 9mm pinfire dies and tools + 12 reloadable cases + 12 percussion cap holders + 1 powder measuring cup

+ 12 firing pins + 25 lead bullets




Firing pins and cap holders are stored in a pretty threaded wood box (French fashion !!!)




KITS PRICE LIST

How does it work

One quite innovative element of this kit is the threaded percussion cap holder. It is a massive piece of brass which no doubt can be used several times before being worn out.




Being threaded at its base, the holder can accommodate a rod that will help greatly to position the holder inside the cartridge case.

Note that each kit (7mm or 9mm) has its own specific cap holder with different technical characteristics (the hole section). The firing pins of both kits being of different size and thickness.




The inside bottom of the 9mm case is thicker - with a shoulder - to adapt the cap holder, while the 7mm case is straight with the cap holder sliding in it with a little play.




1) Screw the threaded rod to the base of the percussion cap holder, and slide a fresh cap into the holder with the cap's opening facing the small hole in the holder.




Note that the percussion cap MUST be flush with the holder. If it remains beyond the holder's edge, as shown above, the holder pin hole, and the case pin hole, will not aligne perfectly and you will have difficulties to enter the firing pin.




2) Drive the cap holder to the bottom of the cartridge case, and insert the firing pin through the case hole into the hole of the cap holder.




Percussion cap not installed

Percussion cap installed

The cap holder is now retained in the bottom of the case by the firing pin. Note that when sticking the pin into the case, you can add before a drop of glue on the pin.

WARNING ! Before adding the bullet it is HIGHLY recommended to test one blank cartridge in the gun you intend to use. Especially if it is a revolver. You must be certain that the pin is - or can be - sufficiently pushed inside the case to allow a free rotation of the cylinder. It may be necessary in some cases to grind down the firing pin.




3) Unscrew the threaded rod from the cap holder, and fill the case with the right quantity of black powder.

Note that :

- for the 7mm caliber any black powder should work (coarse to fine granulation - Fg to FFFg). But if your gun is in very good shape, you can chose a fast burning powder with a finer granulation (FFFg).

- for the 9mm caliber, you should use a fast (fine granulation) powder (FFFg or FFFFg) because of the bullet important dragging inside the barrel, and the rather short case capacity.

The good choice will eventually be the result of experimenting different loads with your own gun.

You should not leave any gap of air between the powder and the bullet. Of course when filling the case you must leave enough space above the powder to allow the seating of the bullet into the case.

Black Powder comes in four granulations. Fg being the coarsest (slowest to burn), and FFFFg being the finest (fastest to burn). You will find the same grades under the following labels : 1Fg to 4fg or even 1F to 4F

Warning ! From now on, a sufficient blow onto the pin can ignite the primer and the powder.




Federal law allows unlicensed individuals to possess no more than 50 pounds of commercially manufactured black powder for use in antique firearms or replicas and reproductions of antique firearms for hunting, sporting or cultural purposes only. Any other use of black powder is a felony. Local ordinances may further restrict the possession and storage of black powder, It is your responsibility to know and obey local statutes and regulations.




Left : 7mm (about 4 grams) - Mid : 9mm (about 9 grams) - Right : 12mm (about 10,80 grams)

4) Place the cartridge case on the slit basement as shown above, and place a bullet onto the case opening. Then put the crimper block on the basement.




You will note that the bullet is shaped with a shoulder. This will help you to know how deep the bullet must be pushed inside the case. All the bullet body under the shoulder must be inside the case.

5) Inserting the bullet into the case with the required deepness, is precisely done thanks to a pushing tool.

This tool is a cylindrical casing into which is screwed a large rod with a concave under face to mate the bullet head profile, and a nut on its upper portion to set the right deepness of the rod that slides into the crimper block channel.

To determine the exact deepness you will install the first bullet by pushing it through the pushing tool (using a light non




marring hammer) until you feel - or better you see - that the bullet shoulder is at the cartridge case upper edge level.

Then, while maintaining the pushing rod in contact with the bullet's head, turn the pushing tool casing down until it is against the crimper block. When it is done, screw firmly the nut against the casing.

The pushing rod is set now at the right deepness for the cartridges to come.

For the next cartridges, just install the bullet on the case, put the pushing tool on the crimper block, and use a mallet to drive the bullet inside the case through the pushing tool rod (which is now firmly locked at the right height to the pushing body by the nut).

CRIMPING PUNCHES NO LONGER FURNISHED(Considered unuseful)

6) If for any reason you want the bullet to be more crimped by the case, you can use the two small punches furnished to this




effect.

The two punches must be inserted in the lateral holes of the crimper block as shown above. The space between the punches and the crimper block surface indicates the deepness of the penetration into the cartridge case when the blow will occur.

Take care to not puncture the cartridge case when performing this additionnal crimping.

To prevent a possible perforation of the cartridge case you can :

- Adjust the punches length by filing them down. - Or add a strip of adhesive tape around the crimper block to enlarge its diameter to the required thickness.- Or add washers to the punches.

In some revolvers, the firing pin, when positioned vertically, can affect the good rotation of the cylinder. You can solve the problem by slightly slanting (about 3 degrees) the firing pin toward the rear.

AFTER FIRING :




1) De-caping

Remove the firing pin. Screw the threaded rod into the percussion cap holder, and pull it out of the cartridge case.

If you want to re-use the case and the cap holder, do not forget to clean them. You can use hot water with some sort of current ammoniacal detergent.




8) To resize the case, use the crimper block as a swaging die (shown above). Do not forget to externally lubricate the case before forcing it into the tool.




9) When the case is resized, eject it with the rod furnished to this effect, by pushing it out of the crimper block as shown above. The case is now ready for another reloading.

If used in rather well calibrated guns with clean smooth chambers such cases should be reloaded five or six times before being discarded as a safety measure. But ALWAYS check attentively the case before any re-use. And specialy in the weaker area of the firing pin hole.




Test the 7mm Pinfire with our Mini Kit

Content : 5 lead bullets + 5 cartridge cases + 5 firing pins + 5 percussion cap holders, and a screw to hold the cap holder.Note that percussion cap shown are removed when shipping to the USA

This starting Mini Kit is sold for : US$36,00 Shipping by unregistered mail included




Test the 9mm Pinfire with our Mini Kitsame as above but in 9mm

Content : 5 lead bullets + 5 cartridge cases + 5 firing pins + 5 percussion cap holders.Note that percussion cap shown are removed when shipping to the USA


Test the 11/12mm Pinfire with our Starter Kit

Content : 5 lead bullets + 5 cartridge cases + 5 firing pins + 5 percussion cap holders.Note that percussion cap shown are removed when shipping to the USA


Basic one shell 16 gauge caliber kit for pinfire shotgun

User manual click here




Includes a brass case, a cap holder, a firing pin and a long screw

$32,00 shipping included (out of Europe shipment)

21,00 Euros shipping included (Europe shipment)

KITS PRICE LIST : http://hlebooks.com/pinfire/prices.htm

Email : [email protected]



mailto:[email protected]



Revive Your Antique Pinfire Handguns

Documents

Transcript of Revive Your Antique Pinfire Handguns