Review of IC-92AD
description
Transcript of Review of IC-92AD
![Page 2: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/2.jpg)
Capabilities• Dual band, dual VFO transceiver
• VFO-a: Wide band receive; FM only• VFO-b: FM and D-STAR capable
• Four power settings• 5 W (H), 2.5 W (M), 0.5 W (L), 100 mW (S)
• 850 memories for VFO-a • 450 memories for VFO-b
![Page 3: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/3.jpg)
Basic Controls• PTT• Volume Control• Memory/Freq Selector• Microphone• VFO a/b Selector• Lock Key• VFO/Mem/Call
Buttons
![Page 4: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/4.jpg)
Review of the Keypad
• Most common functions available from the keypad
• Direct frequency entry
• Backlit keypad for operation in dim environments
![Page 5: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/5.jpg)
What is on the DisplayPrimary
VFO
Freq/Mem Label
Mem Chan
Battery Level
Bank ChanModulation
Mode S-Meter
Repeater Offset
Tone/Squelch
![Page 6: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/6.jpg)
• VFO is used to tune to an arbitrary frequency• Don’t forget repeater offset, tone, squelch
• Memories allow all the settings to be stored for quick retrieval
VFO vs. Memories
VFO
000
001
002
003
004
W7GLB
147.080
446.000
Simplex
TSQL
156.7103.5
DUP+
![Page 7: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/7.jpg)
IC-92AD Memory Structure
• The memories for VFO-a and VFO-b are completely separate
• Each VFO has a pre-assigned number of memories and 2 call memories• VFO-a: 850 • VFO-b: 450
![Page 8: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/8.jpg)
Saving VFO to Memory• First step is to set the VFO with all the settings to program
the memory with• Frequency, tone, offset, squelch, power
• Press and hold for 1 second • Rotate channel selector dial to find blank memory or
desired memory entry to program
• Use and to set bank and memory label• Press and hold for 1 second to program
![Page 9: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/9.jpg)
ICOM Memory Banks
• Memory banks are used to organize programmed memories into functional groups
• 26 banks ( A – Z )
• Up to 100 memories per bank ( 00 – 99 )
• Great to use for traveling between areas or “modes”• normal use, public service events, emcomm and interop channels
![Page 10: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/10.jpg)
Critical Menu Functions• Menus on both VFOs
• SET MODE• Power save, Weather alert, Attenuator, Lock
• DUP/TONE• Repeater and CTCSS tone, DTCS code, Offset
• D-STAR Menus ( VFO-b)• CALL SIGN (also press for 1 second—triple beep)
• Modify UR, RPT1 (R1), RPT2 (R2) and MYCALL (MY)• DV SET MODE
• DV DATA TX, GPS TX MODE
![Page 11: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/11.jpg)
Setting Power Levels• Each band (i.e. 2m or 70cm) has separate power level
settings
• Press and hold for 1 second to switch power levels• High(5W) -> Med(2.5W) -> Low(0.5W) -> Super Low(100mW)
• Tip: Rotate channel selector while holding
![Page 12: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/12.jpg)
Setting Subaudible Tones• Subaudible tone and DTCS are set in the
DUP/TONE menu• Subaudible tone has both repeater (TX) and CTCSS (RX)
settings
• Don’t forget to enable the squelch setting!!!• Hold for 1 second to set TONE, TSQL or DTCS• Tip: Rotate channel selector while holding
![Page 13: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/13.jpg)
Setting Repeater Offset• Standard band offsets are already programmed into the
IC-92AD• Non standard offset can be set through the OFFSET entry
in the DUP/TONE menu
• Hold for 1 second to switch positive, negative and no offset
• Tip: Rotate channel selector while holding
![Page 14: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/14.jpg)
Setting Modulation Mode• The IC-92AD can use FM, FM-N (narrow band), WFM
(wide band, RX only), DV (D-STAR) and AM (RX only) modulation modes
• AM is also used in the aircraft bands
• Hold for 1 second to switch modes• Tip: Rotate channel selector while holding
![Page 15: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/15.jpg)
Two Minute Intro to D-STAR• D-STAR allow simultaneous transmission of voice and
data at the same time
• D-STAR does not use tone or DTCS
• D-STAR still uses repeater offsets
• D-STAR introduces Call Sign memories to enable transmission to be routed through repeater or over the internet
![Page 16: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/16.jpg)
D-Star Addressing• Four items are necessary in order to communicate on the
D-Star network
• UR: The final destination of your transmission. Used for callsign routing, linking and unlinking from reflectors, and STARnet Digital talk groups.
• RPT1: Your entry point in to the D-Star network. This is almost always the callsign of the the local repeater and the port you are using.
• RPT2: Used for cross banding and sending transmissions over the internet through the gateway. Most of the time this is set to the callsign of the repeater with the port of “G” to access the gateway.
• MY: The callsign that you are transmitting with. Allows others to see who is transmitting and how to transmit back to you.
![Page 17: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/17.jpg)
Special Broadcast Callsign
• To address all users, the UR memory gets set to CQCQCQ.
• Most of the time when you transmit on D-STAR your UR memory will be set to CQCQCQ.
• If you are really not sure what your UR memory should be set to, start with setting it to CQCQCQ and try to make contact.
![Page 18: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/18.jpg)
Special UR Callsigns
• When working with a repeater, there are two callsigns to invoke special functions. Always use the callsign of the repeater in the UR.
• Use an eighth character of I to request link status.
• Use an eighth character of E to request an echo test.
• RPT2 must be set to the repeater’s gateway port.
![Page 19: Review of IC-92AD](https://reader035.fdocuments.in/reader035/viewer/2022062315/568164c0550346895dd6d2f9/html5/thumbnails/19.jpg)
Go Forth and Play• The only real way to learn the radio is to play with it and
make mistakes. We have all made the mistakes
•Don’t worry!
• Become regular participants on Nets (not just the one for your club)
• Get up on the Mike and Key repeater (K7LED) and talk to lots of people. Awful lot of experience out there that you can learn from
•Most of all just have fun