Rev P PART'S MANUAL - Home - RhinoAg out the Warranty Registration Form in full and return it within...
Transcript of Rev P PART'S MANUAL - Home - RhinoAg out the Warranty Registration Form in full and return it within...
© 201 Alamo Group Inc.
RHINO®
1020 S. Sangamon Ave.Gibson City, IL 60936800-446-5158Email: [email protected]
PART'S MANUALAn Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOWthe Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Servis-Rhino (800-446-5158) to obtain a Free copy before operating the equipment.
TW14
ROTARY MOWERRev 11 Part No. 00792245P
TO THE OWNER/OPERATOR/DEALERAll implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator whorecognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement tobe used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Formin full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Cardand on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophicfailure with possible injury or death.
PARTS SECTION
Parts Section – 1
Parts Section – 2©2016 Alamo Group Inc.
For maximum safety and to guarantee optimum product reliability, always use genuine Servis-Rhino Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to:
The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong tothe basic machine featured in this manual. Part Numbers and Descriptions are given to helplocate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organizationordering the parts, who should be charged, and if possible, the serial number of the machinefor which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correctpart number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stockedand are subject to special handling. Request a quotation for such parts before sending aPurchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals.
PARTS ORDERING GUIDE
RHINO®
1020 S. Sangamon Ave.Gibson City, IL 60936800-446-5158Email: [email protected]
PART NAME INDEX
A-FRAME ASSEMBLY................................................................................................................................................................................ 4
BLADE CARRIER ASSEMBLY.................................................................................................................................................................. 5
CANISTER ASSEMBLY.............................................................................................................................................................................. 7
DECALS......................................................................................................................................................................................................... 8
DEFLECTOR ASSEMBLY......................................................................................................................................................................... 10
DRIVELINE ASSEMBLY - 00789312 CAT3 SLIP CLUTCH.................................................................................................................. 11
DRIVELINE ASSEMBLY - 00789314 CAT3 SHEAR BOLT................................................................................................................... 13
GEARBOX ASSEMBLY - 50075165 540RPM.......................................................................................................................................... 15
GEARBOX ATTACHMENT...................................................................................................................................................................... 17
TAILWHEEL ASSEMBLY......................................................................................................................................................................... 19
©2016 Alamo Group Inc. Parts Section -3
TW14
A-FRAME ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION1 00757949 1 TOP LINK
2 00792230 2 BRACE, REAR TW14
3 00764839 2 A-FRAME BAR
4 00757953 1 BUSHING 1-1/4X7/32X3 A-FRAME
5 37107B12 1 CLEVIS PIN, TOP LINK - CAT. I
6 37107B13 1 PIN, HAIR CLIP
7 00037200 1 NUT,HEX TOPLOCK 3/4 NC GR.C PL
8 00603500 2 ASY,CAT.1 HITCH PIN W/LW & NUT
9 2196 2 CLIP (LYNCH PIN), 13/32 DIA.
10 00001800 2 LOCKNUT TLM 1/2 NC PLC
11 00749130 2 HHCS 1/2-13UNC 1-3/4 PL5
12 00748598 1 HEXB 3/4-10 UNC 5-1/2 PL 5
©2016 Alamo Group Inc. Parts Section -4
TW14
BLANK INTENTIONALLY
©2016 Alamo Group Inc.
TW14
BLADE CARRIER ASSEMBLY
©2016 Alamo Group Inc. Parts Section -5
TW14
BLADE CARRIER ASSEMBLY
Continued...
ITEM PART NO. QTY. DESCRIPTION1 00792191 1 WDMT, 15IN BLADE CARRIER
2 00781343 2 BLADE, FAN CCW, 16-1/2 CTR-TIP
3 00750226 2 NUT TOPLOCK 7/8 NF PLC
4 00761535 2 WASHER,7/8" STRUCTURAL - PLAIN
5 00781320 2 BLADE BOLT 7/8 DIA X 3 LG
©2016 Alamo Group Inc. Parts Section -6
TW14
CANISTER ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION1 00776031 1 CANISTER, PARTS MANUAL
2 00780878 3 RIVET, 3/16 POP X 15/32" G.R.
©2016 Alamo Group Inc. Parts Section -7
TW14
DECALS
©2016 Alamo Group Inc. Parts Section -8
TW14
DECALS
Continued...
ITEM PART NO. QTY. DESCRIPTION1 02738332 2 RED OBLONG REFLECTOR
2 00792240 1 MODEL TW14 - S/N
3 00781352 1 SHEET, SINGLE SPINDEL SAFETY DECAL
3.1 D614 2 DANGER THROWN OBJECT
3.2 D388 1 DANGER PTO
3.3 00756004 1 DANGER-SHIELD MISSING
4 00792239 1 SHEET, DECAL LOGO-TW14
4.1 D395 1 WARNING-BLADE ATTACHMENT
4.2 D590 1 DANGER/GREASE LOCATION
D814 1 DANGER/GREASE LOCATION
4.3 00760657 1 SAFETY WARNING
4.4 D137 1 BLADE ROTATION CCW
4.5 00792190 2 RHINO-BLACK 6" TALL
©2016 Alamo Group Inc. Parts Section -9
TW14
DEFLECTOR ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION1 00792227 1 BAND, TW14 REAR
2 00792232 1 DEFLECTOR, RUBBER TW14
3 4528 17 NUT, HEX LOCK 3/8-16 FLG WHIZ
4 26168 5 CRG-BLT 3/8 X 1 GR5
5 00011400 12 HEXB 3/8" NC X 1" PL5
6 00011100 4 FLATWASHER 3/8 PL STD
7 00792200 1 WDMT, DECK-TW14
©2016 Alamo Group Inc. Parts Section -10
TW14
DRIVELINE ASSEMBLY - 00789312 CAT3 SLIP CLUTCH
©2016 Alamo Group Inc. Parts Section -11
TW14
DRIVELINE ASSEMBLY - 00789312 CAT3 SLIP CLUTCH
ITEM PART NO. QTY.
8 00756004 1
9 00756005 1
11 00789310 1
12 00789311 1
14 00789044 1
DESCRIPTION COMPLETE DRIVESLINE
YOKE WITH COLLAR
COLLAR KIT
CROSS KIT
FRICTION CLUTCH
SPRING AND BOLT KIT
CLUTCH PAD
BOLT, 1/2 UNC X 3 GR8
NUT, TOPLOCK 1/2-13
SAFETY DECAL INNER
SAFETY DECAL OUTER
OUTER SHIELD BEARING
INNER SHIELD BEARING
SHIELD COMPLETE
©2016 Alamo Group Inc. Parts Section -12
TW14
00789312SP 1
1 1
2 1
3 2
4 1
5 8
6 1
7 1
00789304
00789305
00789306
00789307
00789308
76194
00753013
00001800 1
DRIVELINE ASSEMBLY - 00789314 CAT3 SHEAR BOLT
©2016 Alamo Group Inc. Parts Section -13
TW14
DRIVELINE ASSEMBLY - 00789314 CAT3 SHEAR BOLT
Continued...
4 00756004 1
5 00756005 1
6 00789315 1
7 314013C 1
00001800 1
SAFETY DECAL, INNER
SAFETY DECAL, OUTER
COMPLETE SHIELD KIT
BOLT, 1/2 UNC X 3 GR2
NUT, TOPLOCK 1/2-13
©2016 Alamo Group Inc. Parts Section -14
TW14
ITEM PART NO. QTY.00789314 1
1 1
2 2
3
00789317
00789306
00789316 1
DESCRIPTIONDRIVELINE ASSY.
PUSH PIN YOKE ASSY
CROSS BEARING KIT
YOKE, PLAIN BORE
GEARBOX ASSEMBLY - 50075165 540RPM
©2016 Alamo Group Inc. Parts Section -15
TW14
GEARBOX ASSEMBLY - 50075165 540RPM
Continued...
ITEM PART NO. QTY. DESCRIPTION50075165 1 GEARBOX ASSEMBLY
1 N/A 1 HOUSING
2 81630 1 SPACER
3 81631 3 RETAINING RING
4 50075908 1 PINION
5 70229 1 BEARING ASSY.
6 81634 1 SHAFT, INPUT
7 88851 1 PLUG, PRESSURE RELIEF
8 50075892 1 GEAR, INPUT
9 50052055 1 SHIM, .50MM
50052053 1 SHIM, .15MM
50052054 1 SHIM, .30MM
10 81637 1 RETAINING RING
11 88879 1 SEAL
12 50029491 1 CAP
13 20034 10 CAPSCREW 3/8” X 1’ GR.5
14 15812 10 LOCKWASHER 3/8”
15 70256 3 BEARING ASSY.
16 50052058 1 SHIM, .50MM
50052056 1 SHIM, .15MM
50052057 1 SHIM, .30MM
17 81643 1 CAP
18 81644 1 SEAL
19 88873 1 HEX NUT, SLOTTED 1”
20 81648 1 COTTER PIN
21 69BH 1 PIPE PLUG
22 81445 1 SNAP RING, DRIVELINE RETAINER
©2016 Alamo Group Inc. Parts Section -16
TW14
GEARBOX ATTACHMENT
©2016 Alamo Group Inc. Parts Section -17
TW14
GEARBOX ATTACHMENT
Continued...
ITEM PART NO. QTY. DESCRIPTION1 50075165 1 ASSY, GEARBOX
2 00785946 1 KIT/ GEARBOX SHIELD & RING
3 00023500 4 FLATWASHER, 5/16 PL
4 00035900 4 BOLT, HEX HD 5/16 X 3/4 GR5
5 00695100 4 NUT, TOPLOCK 5/8 NC PLC
6 00756077 4 WASHER,5/8 HARDENED
7 02845500 4 HEXB, 5/8 NC X 2 PL5
©2016 Alamo Group Inc. Parts Section -18
TW14
TAILWHEEL ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION1 00792222 1 WDMT, TAILWHEEL TW14/15/16
2 00787394 1 ASY, WHEEL FORK & SOLID TIRE, 15 X 4-1/2"
3 00792226 1 PLATE,TAILWHEEL ADJUST-TW14/15/16
4 4528 4 NUT, HEX LOCK 3/8-16 FLG WHIZ
5 00011400 2 HEXB 3/8" NC X 1" PL5
6 00001800 2 LOCKNUT TLM 1/2 NC PLC
7 00749130 2 HHCS 1/2-13UNC 1-3/4 PL5
©2016 Alamo Group Inc. Parts Section -19
TW14
BLANK INTENTIONALLY
©2016 Alamo Group Inc.
TW14
LIMITED WARRANTY
1. LIMITED WARRANTIES1.01. Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal
purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased are free from defects in material or workmanship.
1.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.
1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,
lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal
in your Operator’s Manual.1.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any
nature on behalf of Manufacturer.2. REMEDIES AND PROCEDURES.
2.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturerwithin 30 days of purchase.
2.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased thegoods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based.
2.03. Purchaser is responsible for returning the goods in question to the Dealer.
service due to defects in material or workmanship, Manufacturer will:(a) Repair or replace the defective goods or part(s) or(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)
by Manufacturer.The choice of remedy shall belong to Manufacturer.
2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the trans-
portation cost for the goods or part(s) from the Dealer to the designated factory.3. LIMITATION OF LIABILITY.
3.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIESWITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.3.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR
USE OF THE GOODS.3.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO
PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.
3.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.
4. MISCELLANEOUS.4.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,
Texas.4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall
be deemed to be a waiver of any other term.4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the
invalidity of such provision shall not invalidate any other provisions herein.
KEEP FOR YOUR RECORDS
Servis-Rhino Implement Model _______________________________ Serial Number ________________________________
Date Purchased ___________________________________________ Dealer ______________________________________
ATTENTION: READ YOUR OPERATOR'S MANUAL
SERVIS-RHINO
1020 S. Sangamon Ave.Gibson City, IL 60936800-446-5158Email: [email protected]
RHINO®
TO THE OWNER/OPERATOR/DEALER
The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety require-ments of tractor operators:
REQUIRED OF THE OWNER:
1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and3. Ensure that each employee uses such Seatbelt while the tractor is moving; and
-tected area provided by the ROPS.
REQUIRED OF THE OPERATOR
1. Securely fasten seatbelt if the tractor has a ROPS.2. Where possible, avoid operating the tractor near ditches, embankments, and holes.3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.4. Stay off slopes too steep for safe operation.5. Watch where you are going - especially at row ends, on roads, and around trees.6. Do not permit others to ride.7. Operate the tractor smoothly - no jerky turns, starts, or stops.8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.9. When the tractor is stopped, set brakes securely and use park lock, if available.
Part No. 00792245PTW14Printed U.S.A.