First-order, buckling and post-buckling behaviour of GFRP ...
Research Article On the Shear Buckling of Clamped Narrow...
Transcript of Research Article On the Shear Buckling of Clamped Narrow...
-
Research ArticleOn the Shear Buckling of Clamped NarrowRectangular Orthotropic Plates
Seyed Rasoul Atashipour and Ulf Arne Girhammar
Department of Civil, Environmental and Natural Resources Engineering, Division of Structural andConstruction Engineering-Timber Structures, LuleaΜ University of Technology, 971 87 LuleaΜ, Sweden
Correspondence should be addressed to Seyed Rasoul Atashipour; [email protected]
Received 19 October 2015; Accepted 29 October 2015
Academic Editor: Francesco Tornabene
Copyright Β© 2015 S. R. Atashipour and U. A. Girhammar. This is an open access article distributed under the Creative CommonsAttribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work isproperly cited.
This paper deals with stability analysis of clamped rectangular orthotropic thin plates subjected to uniformly distributed shearload around the edges. Due to the nature of this problem, it is impossible to present mathematically exact analytical solution forthe governing differential equations. Consequently, all existing studies in the literature have been performed by means of differentnumerical approaches. Here, a closed-form approach is presented for simple and fast prediction of the critical buckling load ofclamped narrow rectangular orthotropic thin plates. Next, a practical modification factor is proposed to extend the validity of theobtained results for a wide range of plate aspect ratios. To demonstrate the efficiency and reliability of the proposed closed-formformulas, an accurate computational code is developed based on the classical plate theory (CPT) bymeans of differential quadraturemethod (DQM) for comparison purposes. Moreover, several finite element (FE) simulations are performed via ANSYS software.It is shown that simplicity, high accuracy, and rapid prediction of the critical load for different values of the plate aspect ratio andfor a wide range of effective geometric and mechanical parameters are the main advantages of the proposed closed-form formulasover other existing studies in the literature for the same problem.
1. Introduction
The shear buckling analysis of clamped composite plates isof great importance in design of many types of engineeringstructures. Unlike the problem of normal buckling of plates,the shear buckling problem of plates is mathematicallydescribed by differential equations having a term with odd-order of derivatives with respect to each of the planar spatialcoordinates. Therefore, their governing equations cannot besolved exactly. Such problems are almost always analysedand solved using different numerical approaches. Apart fromthe loading type, clamped boundary conditions at all plateedges make the problem more difficult for finding an exactanalytical solution.
During the past decades, many investigators have studiedthe shear buckling problem of rectangular plates. One of thefirst efforts dealing with shear buckling analysis of clampedisotropic plates with finite dimensions can be attributedto Budiansky and Conner [1] using Lagrangian multiplier
method. A useful review of the studies on the shear bucklingof both isotropic and orthotropic plates was presented byJohns [2]. Shear buckling analysis of antisymmetric cross ply,simply supported rectangular plates was carried out by Hui[3] using Galerkin procedure. Kosteletos [4] studied shearbuckling response of laminated composite rectangular plateswith clamped edges using Galerkin method. Biggers andPageau [5] computed shear buckling loads of both uniformand composite tailored plates using finite element method.Xiang et al. [6] employed pb-2 Rayleigh-Ritz approach toobtain critical shear loads of simply supported skew plates.Loughlan [7] studied the shear buckling of thin laminatedcomposite plates and examined the effect of bend-twistcoupling on their behaviour using a finite strip procedure.Lopatin and Korbut [8] utilized the finite difference methodto investigate the shear buckling of thin clamped orthotropicplates. Shufirn and Eisenberger [9] analysed the buckling ofthin plates under combined shear and normal compressiveloads using the multiterm extended Kantorovich method.
Hindawi Publishing CorporationMathematical Problems in EngineeringVolume 2015, Article ID 569356, 11 pageshttp://dx.doi.org/10.1155/2015/569356
-
2 Mathematical Problems in Engineering
The shear buckling load of rectangular composite platesconsisting of concentric rectangular layups was investigatedby Papadopoulos and Kassapoglou [10] by means of aRayleigh-Ritz approach. Wu et al. [11] calculated the criticalshear buckling loads of rectangular plates by the extendedspline collocation method (SCM). Uymaz and Aydogdu [12]carried out the shear buckling analysis of functionally gradedplates for various boundary conditions based on the Ritzmethod. Shariyat and Asemi [13] performed a nonlinearelasticity-based analysis for the shear buckling of rectangularorthotropic functionally graded (FG) plates surrounded byelastic foundations using a cubic B-spline finite elementapproach.
Evidently, all the above-mentioned numerical studieshave some deficiencies like convergence difficulties andbeing time-consuming compared to analytical and closed-form solutions. Therefore, it is not easy and time-efficientto predict the critical shear buckling loads and investigatethe effect of various parameters by the use of numericalsolution approaches. To the best of authorsβ knowledge, noclosed-form solution can be found in the literature for theshear buckling of composite rectangular plates with finitedimensions. To fill this apparent void, the present work iscarried out to provide efficient and reliable explicit formulasfor rapid prediction of the fundamental critical shear buck-ling loads of clamped orthotropic rectangular plates. Therange of validity of the proposed closed-form formulas isextended by introducing a practical modification factor. Also,in order to demonstrate the efficiency and reliability of theproposed closed-form formulas, an accurate computationalcode is developed bymeans of differential quadraturemethod(DQM) for comparison purposes. Moreover, several finiteelement (FE) simulations are performed via ANSYS software.
This paper is only devoted to a principle study of theshear buckling behavior and, for illustration, is applied to alaminated veneer lumber (LVL) panel. Other failure modes,such as the shear strength, are not included in the analysis.
2. Definition of the Problem andGoverning Equations
Consider a clamped narrow rectangular orthotropic plateof length π, width π, and thickness π‘, subjected to a uni-formly distributed shear load per length π
π₯π¦(Figure 1). The
coordinates system is shown in the figure. We employ theclassical plate theory (CPT) of Kirchhoff to study the shearbuckling of thin plates. The governing equation of CPT forthe orthotropic plates is expressed as
π·11
π4
π€
ππ₯4+ 2 (π·
12+ 2π·33)
π4
π€
ππ₯2ππ¦2+ π·22
π4
π€
ππ¦4
= 2ππ₯π¦
π2
π€
ππ₯ππ¦
,
(1)
whereπ€ is transverse displacement, andπ·ππare stiffness coef-
ficients of orthotropic materials and are defined as follows:
π·11=
πΈ1π‘3
12 (1 β ]12]21)
,
π·12=
]21πΈ1π‘3
12 (1 β ]12]21)
,
π·22=
πΈ2π‘3
12 (1 β ]12]21)
,
π·33=
1
12
πΊ12π‘3
(2)
in which πΈ1and πΈ
2are modulus of elasticity of orthotropic
material inπ₯ andπ¦directions, respectively;πΊ12is the in-plane
shear modulus and ]ππare the Poissonβs ratios.
The plate is assumed to be fully clamped. Thus, thefollowing boundary conditions should be considered at theplate edges:
π€|π₯=0,π
= 0,
π€|π¦=0,π
= 0,
(3a)
ππ€
ππ₯
π₯=0,π
= 0,
ππ€
ππ¦
π¦=0,π
= 0.
(3b)
3. An Efficient Closed-Form Solution
As mentioned earlier, no exact analytical approach exists forthe problem of shear buckling of rectangular orthotropicplates, not only due to the loading type, but also becauseof the fully clamped boundary conditions. The computa-tional numerical approaches are usually time-consumingfor obtaining the results with adequate accuracy. Therefore,it is reasonable to find an efficient method for predictingthe critical loads. Timoshenko and Gere [14] presented anapproximate solution for the shear buckling of narrow rectan-gular plates with the limitation of simply supported boundaryconditions and isotropic material. We start by extending themethod for the orthotropic narrow rectangular plates withclamped boundary conditions. To this end, we consider thefollowing expression for the transverse displacement of thebuckled plate:
π€ (π₯, π¦) = [1 β cos(2ππ
π¦)] β sin [ππ
(π₯ β πΌπ¦)] , (4)
where π and πΌ represent the length of half-waves of thebuckled plate and the slope of the nodal lines. Clearly, (4)satisfies the clamped edge conditions at the long edges π¦ =0, π. However, this approximate approach is not capable ofsatisfying the clamped boundary conditions at the two short
-
Mathematical Problems in Engineering 3
y
xa
b
tSxy
Sxy
Figure 1: Geometric configuration and coordinate system of a narrow rectangular orthotropic plate with fully clamped edges subjected to auniformly distributed shear load.
edges. The work done by the external forces and the strainenergy during the buckling of the plate are defined by
Ξπ = βπcr β«2π
0
β«
π
0
ππ€
ππ₯
ππ€
ππ¦
ππ₯ ππ¦,
Ξπ =
1
2
β«
2π
0
β«
π
0
[π·11(
π2
π€
ππ₯2)
2
+ π·22(
π2
π€
ππ¦2)
2
+ 2π·12(
π2
π€
ππ₯2)(
π2
π€
ππ¦2)
+ 4π·33(
π2
π€
ππ₯ππ¦
)
2
]ππ₯ππ¦.
(5)
By substituting the proposed form of the transverse displace-ment from (4) into (5) and equating the work of externalforces to the strain energy (i.e., Ξπ = Ξπ), a closed-formformula is obtained for the critical buckling load as
πcr =π2
π 2
6π4πΌ
{16π·22
+ 8 [(π·12+ 2π·33) + 3π·
22πΌ2
] (
π
π
)
2
+ 3 [π·11+ 2 (π·
12+ 2π·33) πΌ2
+ π·22πΌ4
] (
π
π
)
4
} .
(6)
The obtained formula for the critical buckling load should beminimized with respect to the unassigned parameters π andπΌ. To this end, we differentiate (6) one time with respect to π and then with respect to πΌ. It is easy to show that the resultedset of algebraic equations can be represented as
3π·11+ 4 (π·
12+ 2π·33) (
π
π
)
2
β 12π·22(
π
π
)
2
πΌ2
β 3π·22πΌ4
= 0,
3π·11+ 6 (π·
12+ 2π·33) πΌ2
+ 3π·22πΌ4
β 16π·22(
π
π
)
4
= 0.
(7)
Exact solution of the above set of equations can be repre-sented in the form
πΌ =
β2
2
β ββ
πΏ2(7πΏ1β 19πΏ
2
2/3)
βπΏ3+ πΏ4/β + β/3
+ 2πΏ3β
πΏ4
β
β
β
3
+ βπΏ3+
πΏ4
β
+
β
3
β πΏ2,
(8)
where
β =
3βπΏ5+ βπΏ2
5β 27πΏ
3
4.
(9)
Also, the parameter π is expressed in terms of πΌ as follows:
π =
π
2
4β3 (πΏ
1+ 2πΏ2πΌ2+ πΌ4). (10)
In (8) through (10), the coefficients πΏπ(π = 1, 2, . . . , 5) are
defined as
πΏ1=
π·11
π·22
,
πΏ2=
π·12
π·22
,
πΏ3= β
5
3
(
π·11
π·22
) +
20
9
(
π·12
π·22
)
2
,
πΏ4=
1
12
(
π·11
π·22
)
2
β
7
18
(
π·11
π·22
)(
π·12
π·22
)
2
+
49
108
(
π·12
π·22
)
4
,
πΏ5=
485
8
(
π·11
π·22
)
3
β
587
8
(
π·11
π·22
)
2
(
π·12
π·22
)
2
+
293
24
(
π·11
π·22
)(
π·12
π·22
)
4
+
181
216
(
π·12
π·22
)
6
(11)
in which
π·12= π·12+ 2π·33. (12)
-
4 Mathematical Problems in Engineering
For the isotropic case, πΏ1= πΏ2= 1 and, consequently, the
parameters πΌ and π from (8)β(11) are reduced to
πΌ =
1
4β3
,
π =
π
2
β1 + β3.
(13)
Therefore, the critical buckling load from (6) is reduced to
πcr =8
3
4β3 (β3 + 1)
π2
π·
π2. (14)
It is worth to rewrite the obtained closed-form formula in theconventional form as follows:
πcr = ππ π2
π·11
π2
. (15)
Therefore, the dimensionless coefficient ππ is represented in
the form
ππ =
4
3πΏ1πΌ
{β3 (πΏ1+ 2πΏ2πΌ2+ πΌ4) + πΏ2+ 3πΌ2
} (16)
in which the coefficients πΌ, β, and πΏπ(π = 1, 2, . . . , 5) are
defined by (8), (9), and (11).It will be shown that the obtained closed-form formulas
accurately predict the critical buckling load of a narrowrectangular orthotropic plate in shear with clamped edges.Apparently, the accuracy of the obtained closed-form for-mulas decreases when the plate aspect ratio decreases. Toenhance the validity range of the obtained formulas for lowervalues of the plate aspect ratio and generalize them, wepropose a simple practical modification factor (πΆmf ) to bemultiplied by the dimensionless coefficient π
π in the form:
πΆmf = 1 +3/πΈ + 1
4 [(π/π)4
+ 1]
. (17)
In the next section, a differential quadrature (DQ) code isdeveloped for comparison purposes to prove the high accu-racy of the proposed closed-form formulas for predicting thecritical buckling load of the rectangular orthotropic plates inshear with clamped edges. Evidently, fast and easy predictionof the critical buckling load is the main advantage of theobtained closed-form formulas over existing studies in theliterature based on time-consuming numerical approaches.
4. Differential Quadrature Solution
The differential quadrature method (DQM), as an appropri-ate method among various numerical solution approaches,has been mostly utilized by scientists for the eigen-bucklinganalysis of composite rectangular plates under in-plane nor-mal compressive loads (e.g., see [15β18]). Here, we employthis methodology to solve the problem of shear bucklingof clamped thin composite plates. To this end, we define
the transverse displacement π€ as a multipolynomial throughdiscretized pointsπ
π,π= π€(π₯
π, π¦π) in the domain:
π€ (π₯, π¦) =
ππ₯
β
π=1
ππ¦
β
π=1
ππ,πππ(π₯) ππ(π¦) , (18)
where ππ₯and π
π¦are the number of grid points in π₯ and
π¦ directions, respectively, and the Lagrange interpolationpolynomials π
π(π₯) and π
π(π¦) are defined in the form
ππ(π₯) =
ππ₯
β
π=1,π ΜΈ=π
π₯ β π₯π
π₯πβ π₯π
,
ππ(π¦) =
ππ¦
β
π=1,π ΜΈ=π
π¦ β π¦π
π¦πβ π¦π
.
(19)
It is assumed that the following equations are satisfied for thefunction π€(π₯, π¦) and its derivatives [19]:
π€(π)
π₯(π₯π, π¦π) =
ππ₯
β
π=1
π(π)
ππππ,π,
π = 1, 2, . . . , ππ₯; π = 1, 2, . . . , π
π₯β 1,
π€(π)
π¦(π₯π, π¦π) =
ππ¦
β
π=1
π(π)
ππππ,π,
π = 1, 2, . . . , ππ¦; π = 1, 2, . . . , π
π¦β 1,
(20)
where π and π are weighting coefficients in the DQM fordifferentiation of π€ with respect to π₯ of order π and π¦ oforderπ, respectively. Details on calculations of the weightingcoefficients, according to Shuβs general approach [19], aregiven in Appendix.
Substituting (20) into (1) results in the discretized govern-ing equation as follows:
π·11
ππ₯
β
π=1
π(4)
ππππ,π+ 2 (π·
12+ 2π·33)
ππ₯
β
π1=1
ππ¦
β
π2=1
π(2)
ππ1
π(2)
ππ2
ππ1 ,π2
+ π·22
ππ¦
β
π=1
π(4)
ππππ,π= 2ππ₯π¦
ππ₯
β
π1=1
ππ¦
β
π2=1
π(1)
ππ1
π(1)
ππ2
ππ1 ,π2
.
(21)
To obtain accurate results, the distribution of the grid pointsshould be denser at the edge-zones.Thus, an appropriate gridpoint distribution pattern is used as
π₯π
π
=
1
2
[1 β cos( π β 1ππ₯β 1
π)] , π = 1, 2, . . . , ππ₯,
π¦π
π
=
1
2
[1 β cos(π β 1
ππ¦β 1
π)] , π = 1, 2, . . . , ππ¦,
(22)
where π₯πand π¦
πare the coordinates of πth and πth grid
points, respectively. Figure 2 shows the mesh distribution ona narrow rectangular domain based on (22).
-
Mathematical Problems in Engineering 5
y
x23
j
Ny...
...
j+ 1
1 2 3 4 i NxΒ· Β· Β· Β· Β· Β·i β 1 i + 1 i + 2
Figure 2: Illustration of the DQ meshed narrow rectangular plate.
The boundary conditions (3a) and (3b) can be rewrittenin the form
π1,π= 0, at π₯ = 0,
πππ₯ ,π
= 0, at π₯ = π,(23a)
ππ,1= 0, at π¦ = 0,
ππ,ππ¦
= 0, at π¦ = π,(23b)
ππ₯
β
π=1
π(1)
1,πππ,π= 0, at π₯ = 0,
ππ₯
β
π=1
π(1)
ππ₯,πππ,π= 0, at π₯ = π,
(24a)
ππ¦
β
π=1
π(1)
1,πππ,π= 0, at π¦ = 0,
ππ¦
β
π=1
π(1)
ππ¦,πππ,π= 0, at π¦ = π.
(24b)
Clearly, (23a) and (23b) can be easily satisfied at the four edgesof the plate. However, (24a) and (24b) cannot be directlysubstituted into (21).This difficulty can be easily overcome byusing a simple method described by Shu and Du [20]. Basedon this approach, the two equations (24a) are coupled to givetwo solutionsπ
2,πandπ
ππ₯β1,πas follows:
π2,π=
1
πΌ0
ππ₯β2
β
π=3
π½πππ,π,
πππ₯β1,π
=
1
πΌ0
ππ₯β2
β
π=3
πΎπππ,π,
π = 3, 4, . . . , ππ¦β 2.
(25)
Using a similar method, the two equations (24b) can becoupled to give two solutions forπ
π,2andπ
π,ππ¦β1:
ππ,2=
1
πΌ0
ππ¦β2
β
π=3
π½πππ,π,
ππ,πβ1
=
1
πΌ0
ππ¦β2
β
π=3
πΎπππ,π,
π = 3, 4, . . . , ππ₯β 2.
(26)
The coefficients πΌ0, π½π, πΎπ, πΌ0, π½πand πΎπ, in (25) and (26), are
defined in Appendix.For the points near the four corners, π
2,2, πππ₯β1,2
,π2,ππ¦β1
, andπππ₯β1,ππ¦β1
can be determined by coupling (24a)and (24b) in the following form:
π2,2=
1
πΌ0πΌ0
ππ₯β2
β
π1=3
ππ¦β2
β
π2=3
π½ππ½πππ1 ,π2
,
πππ₯β1,2
=
1
πΌ0πΌ0
ππ₯β2
β
π1=3
ππ¦β2
β
π2=3
πΎππ½πππ1 ,π2
,
π2,ππ¦β1
=
1
πΌ0πΌ0
ππ₯β2
β
π1=3
ππ¦β2
β
π2=3
π½ππΎπππ1 ,π2
,
πππ₯β1,ππ¦β1
=
1
πΌ0πΌ0
ππ₯β2
β
π1=3
ππ¦β2
β
π2=3
πΎππΎπππ1 ,π2
.
(27)
Hence, the discretized governing equation (21) should beapplied for the interior mesh points in which 3 β€ π β€ π
π₯β 2,
3 β€ π β€ ππ¦β 2.
Applying the discretized governing equation (21) for allthe interior grid points (i.e., 3 β€ π β€ π
π₯β 2, 3 β€ π β€
ππ¦β 2) and satisfying the boundary conditions (23a) and
(23b) together with (25)β(27) will result in a set of algebraicequations in terms ofπ
ππ. These equations can be expressed
in the form of a matrix equation as follows:
AW β πcrBW = 0, (28)
-
6 Mathematical Problems in Engineering
where A and B are two matrices of the coefficients, andW isthe deflection vector in terms ofπ
π,π. Also, πcr is the critical
shear load per length (ππ₯π¦,cr). Generally, the set of algebraic
equations (28) should be of order (ππ₯Γ ππ¦) by (π
π₯Γ ππ¦).
However, the use of (25) and (26) for π2,π, πππ₯β1,π
, ππ,2,
ππ,ππ¦β1
and (27) for π2,2, πππ₯β1,2
, π2,ππ¦β1
and πππ₯β1,ππ¦β1
reduces the order of the algebraic equations to [ππ₯Γ ππ¦β
2(ππ₯+ ππ¦) + 12] by [π
π₯Γ ππ¦β 2(π
π₯+ ππ¦) + 12].
By taking advantage of the reduced algebraic equations,the size of the analysis domain decreases and, consequently,a finer mesh can be used resulting in more accurate eigenval-ues.
5. Numerical Results and Discussion
A mathematical code is developed according to the abovedescribedDQ solution to obtain the accurate critical bucklingloads and their corresponding mode shapes for compari-son studies. Also, some simulations were performed usingANSYS software. It should be pointed out that the assump-tions of the classical plate theory (CPT) are incorporated intothe simulations performed by ANSYS. The results obtainedfrom the proposed closed-form formulas are compared tothose obtained by the DQ code and ANSYS simulations toshow the reliability of the formulas.
To generalize the numerical results, the following dimen-sionless parameters are introduced:
ππ =
π2
π2π·11
πcr =π2
π‘
π2π·11
πcr,
πΈ =
πΈ2
πΈ1
,
πΊ =
2 (1 + ]12)
πΈ1
πΊ12,
(29)
where ππ is dimensionless shear buckling parameter in
terms of the critical load πcr (ππ₯π¦,cr) and the correspondingcritical shear stress πcr, π‘ is the thickness, and πΈ and πΊare dimensionless elasticity and shear moduli of orthotropicmaterial, respectively. As a special case, the orthotropic plateis converted to an isotropic one when πΈ = πΊ = 1.
Table 1 shows a convergence study of the DQ code aswell as comparison of the dimensionless shear bucklingparameter π
π obtained from the closed-form approach, DQ
solution, and those from [1] for fully clamped isotropic plates.The obtained buckling parameters are compared for variousvalues of the aspect ratio (π = π/π) and two different typesof buckling modes: symmetric and antisymmetric. It can beobserved from Table 1 that the obtained critical loads fromboth closed-form formulas and the DQ solution are in a verygood agreement with the results of [1] for different values ofthe aspect ratio. Also, the results of this table confirm theconvergence and stability of the obtained critical loads for allcases.
Variations of dimensionless fundamental shear bucklingparameter π
π versus the plate aspect ratio are depicted in
Figure 3 for different values of the dimensionless materialproperties: πΈ and πΊ. It can be seen from Figure 3 that
Accurate DQ codeClosed-form approach
S
AS
S
S
S
A
A
A
A
A: antisymmetricS: symmetric
S
AS
S
S
A
S
E = 2, G = 1
E = 1, G = 2
E = 1, G = 0.5
E = 1, G = 1(Isotropic)
E = 0.5, G = 1
4
6
8
10
12
14
16
18
20
1 1.5 2a/b
2.5 3 3.5 4
ks
Figure 3: The critical buckling load coefficient for rectangularorthotropic plates under pure uniform shear load versus the aspectratio for different material properties (]
21= 0.3).
the results of the proposed closed-form approach are invery good agreement with those of the time-consumingcomputational DQ solution for all cases, even for squareplates. It is worth noting that the introduced closed-formformulas only predict the fundamental critical loads, eithersymmetric or antisymmetricmode. Although the plate aspectratio influences the type of fundamental shear bucklingmode, their critical loads are very close to each other. Sincethe curves of this figure are provided in dimensionless form,they can be used for estimating the critical shear loads ofclamped orthotropic plates with a wide range of geometricand material properties.
To study the shear buckling of clamped narrow rectan-gular orthotropic plates, a special engineering panel is con-sidered called laminated veneer lumber (LVL). This timbersheathing,with the commercial nameofKerto-Q, is subjectedto a distributed uniform shear load. The mechanical andgeometric properties of LVL are as follows:
πΈ1= 10.5GPa,
πΈ2= 2.4GPa,
πΊ12= 0.6GPa,
]21= 0.05,
π = 3.0m,
π = 0.7275m,
π‘ = 0.027m.
(30)
-
Mathematical Problems in Engineering 7
Table 1: Convergence study and comparison of critical buckling load parameter (ππ ) of fully clamped isotropic rectangular plates with various
values of the aspect ratio (π = π/π) under uniform distributed shear load.
ππ₯Γ ππ¦
ππ = π2
πcr/ (π2
π·11)
π = 1.00 π = 1.25 π = 1.50 π = 2.00 π = 3.00
Sym. Antisym. Sym. Antisym. Sym. Antisym. Sym. Antisym. Sym. Antisym.7 Γ 7 14.938 16.335 12.543 13.488 11.619 12.129 11.358 10.618 12.696 12.9019 Γ 9 14.801 17.307 12.487 13.979 11.602 12.056 10.774 10.418 9.816 10.00511 Γ 11 14.643 16.904 12.347 13.658 11.457 11.797 10.579 10.251 9.568 9.70913 Γ 13 14.642 16.920 12.347 13.671 11.459 11.805 10.583 10.249 9.535 9.62615 Γ 15 14.642 16.919 12.347 13.670 11.458 11.804 10.582 10.248 9.568 9.63217 Γ 17 14.642 16.919 12.347 13.670 11.458 11.804 10.582 10.248 9.569 9.631Closed-form approach 14.382 β 12.374 β 11.170 β β 10.152 9.705 βReference [1] 14.64 β 12.35 β 11.45 11.79 10.58 10.32 9.57 9.64
Table 2: Convergence study and comparison of critical bucklingshear stress, πcr (MPa), of fully clamped orthotropic rectangular plate(LVL) with FEM simulation and the closed-form approach.
ππ₯Γ ππ¦
πcr (MPa)Symmetric mode Antisymmetric mode
7 Γ 7 42.788 43.7019 Γ 9 31.421 32.41011 Γ 11 30.484 31.10713 Γ 13 30.321 30.58215 Γ 15 30.334 30.62317 Γ 17 30.331 30.61719 Γ 19 30.332 30.618Closed-form approach 30.534 βANSYS simulation 30.410 30.694
In order to ensure convergence and accuracy of thedeveloped DQ code for the shear buckling loads of theorthotropic narrowplates, a convergence study is presented inTable 2 for the LVL sheathing. Also, the results are comparedwith those obtained from an accurate FE simulation viaANSYS software as well as the results of the closed-formapproach. It is evident that the obtained critical in-planeshear stresses from the closed-form formulas are in verygood agreement with those achieved from the DQ code andANSYS simulation.
In order to get a better physical sense of the symmetricand antisymmetric modes, the mode shapes of a squareisotropic clamped plate are provided via both the devel-oped DQ code and ANSYS simulation and are illustratedin Figure 4. Also, the symmetric and antisymmetric modeshapes of the LVL narrow rectangular plate are presented inFigure 5 to show the influence of the geometric shape on themode shapes. It can be seen that the mode shapes obtainedby the DQ code are the same as those obtained by ANSYSsimulation. Also, comparison between the correspondingmode shapes of Figures 4 and 5 reveals the fact that thenumber of half-waves increases by increasing the aspect ratio.
In Figure 6, the mode shape of the LVL obtained fromthe closed-form approximation is shown. It can be observedthat the mode shape predicted by this approximate method,
except at the two short edges, is similar to those of othermethods.
Variations of the in-plane shear stress of the clampedLVL plate versus different geometric and mechanical param-eters are shown in Figures 7 and 8, respectively. It shouldbe pointed out that the results in these two figures arepresented in dimensional form to more directly study theinfluence of various parameters on the critical in-plane shearstress. In both figures, the results of DQ code, closed-formapproach and FE simulation via ANSYS are provided toshow the reliability and efficiency of the developed closed-form approach for a wide variety of different geometricand material properties. In Figure 7, π denotes one of thegeometric properties relative to the reference value for theLVL panel and in Figure 8 πΎ represents one of the materialproperties. The subscript βLVLβ in the relative expressionsππ/πLVL and πΎπ/πΎLVL refers to the reference values of the LVL
panel (see (30)). It can be observed from Figure 7 that thecritical buckling stress considerably decreases as the width πof the LVL plate increases, whereas decreasing the length πresults in a small increase of the critical buckling stress. Also,it is evident that the critical stress significantly increases whenthe thickness of the plate increases. However, it should bementioned that for large thicknesses the classical plate theoryis no longer valid due to the neglect of the transverse sheardeformations.
Figure 8 reveals the fact that, by increasing any of thematerial properties, the critical buckling stress increases.It is also obvious that Youngβs modulus πΈ
2has the largest
effect and the shear modulus πΊ12
the smallest effect on thecritical buckling stress of the clamped narrow rectangularorthotropic plate subjected to uniform in-plane shear load.
Influence of Poissonβs ratio ]21
on the critical in-planeshear stress of the clamped LVL is shown in Figure 9 based onthe obtained closed-form formulas, DQ solution, andANSYSsimulations. It can be observed that increasing Poissonβs ratiocan slightly increase the critical shear stress.
In Figures 7β9, very good agreement between the curvesobtained from the closed-form approach and those based ontheDQ code as well as ANSYS simulation shows the accuracyand reliability of the proposed efficient closed-form formulafor all cases.
-
8 Mathematical Problems in Engineering
DQ code ANSYS simulation
(a)
DQ code ANSYS simulation
(b)
Figure 4: Contour plot of themode shape corresponding to the critical buckling loads of a fully clamped isotropic square plate: (a) symmetricmode, (b) antisymmetric mode.
DQ code
ANSYS simulation(a)
DQ code
ANSYS simulation(b)
Figure 5: Contour plot of the mode shape corresponding to the critical buckling loads of a fully clamped orthotropic rectangular plate (LVL):(a) symmetric mode, (b) antisymmetric mode.
-
Mathematical Problems in Engineering 9
Figure 6: Contour plot of the mode shape corresponding to thecritical buckling load of the orthotropic LVL plate based on theclosed-form approach.
0.5 0.75 1 1.25 1.5 1.75 20
20
40
60
80
100
120
Closed-form approachDQ code
ANSYS simulation
π3 = t
π1 = a
π2 = b
LVLref
πi/πLVL
πcr
Figure 7: Effect of different geometric properties on the criticalshear stress of the orthotropic LVL panel. The horizontal axis showsthe relative value of the geometric parameter with reference to thevalue of the LVL panel.
6. Conclusions
In this paper, the shear buckling of clamped narrow rectan-gular orthotropic plates was investigated. An efficient closed-form approach was presented to easily and fastly predict thecritical shear buckling loads and correspondingmode-shapesof the clamped narrow rectangular orthotropic plates. Also,a practical modification factor was proposed to extend thevalidity range of the obtained explicit formulas. To prove theaccuracy and effectiveness of the closed-form approach, anaccurate DQ code was developed and the critical bucklingloads and their corresponding mode shapes were extracted.Also, several accurate FE simulations using ANSYS softwarewere performed. It was shown that the proposed closed-formapproach can predict the critical buckling loads with theacceptable accuracy for a wide range of effective parameterswithout any computational effort. The effect of various geo-metric andmechanical parameters was investigated bymeansof three different methods: closed-form approach, DQ code,and ANSYS simulations. It was observed that the criticalbuckling load considerably decreases by increasing the widthπ of the narrow plates whereas decreasing the length π results
0.5 0.75 1 1.25 1.5 1.75 2
20
25
30
35
40
45
50
Closed-form approachDQ code
ANSYS simulationπ
cr
LVLref
πΎ2 = E2
πΎ1 = E1
πΎ3 = G12
πΎi/πΎLVL
Figure 8: Effect of different material properties on the critical shearstress of the orthotropic LVL panel. The horizontal axis shows therelative value of the material parameter with reference to the valueof the LVL panel.
0.5 0.75 1 1.25 1.5 1.75 2
20
25
30
35
40
45
50
Closed-form approachDQ code
ANSYS simulation
πcr LVLref
οΏ½12/(οΏ½12)LVL
Figure 9: Effect of Poissonβs ratio on the critical shear stress of theorthotropic LVL panel. The horizontal axis shows the relative valueof the material parameter with reference to the value of the LVLpanel.
-
10 Mathematical Problems in Engineering
in a very small increase of the critical buckling load. Also itwas shown, among different material properties, that Youngβsmodulus πΈ
2and the shear modulus πΊ
12have the largest and
smallest effects on the critical buckling load, respectively.
Appendix
Calculation of Weighting andOther Coefficients
The weighting coefficients for the first-order derivatives areexpressed as
π(1)
ππ=
πΌ(1)
(π₯π)
(π₯πβ π₯π) πΌ(1)(π₯π)
,
π(1)
ππ= β
ππ₯
β
π=1,π ΜΈ=π
π(1)
ππ
π, π = 1, 2, . . . , ππ₯, π ΜΈ= π
π(1)
ππ=
π½(1)
(π¦π)
(π¦πβ π¦π) π½(1)(π¦π)
,
π(1)
ππ= β
ππ¦
β
π=1,π ΜΈ=π
π(1)
ππ
π, π = 1, 2, . . . , ππ¦, π ΜΈ= π
(A.1)
in which the functions πΌ and π½ are represented in the form
πΌ(1)
(π₯π) =
ππ₯
β
π=1,π ΜΈ=π
(π₯πβ π₯π) ,
π½(1)
(π¦π) =
ππ¦
β
π=1,π ΜΈ=π
(π¦πβ π¦π) .
(A.2)
The higher-order weighting coefficients are expressed by thefollowing recursive relations:
π(π)
ππ= π(π
(1)
πππ(πβ1)
ππβ
π(πβ1)
ππ
π₯πβ π₯π
) ,
π(π)
ππ= β
ππ₯
β
π=1,π ΜΈ=π
π(π)
ππ
π, π = 1, 2, . . . , ππ₯; π = 2, 3, . . . , π
π₯β 1, π ΜΈ= π,
π(π)
ππ= π(π
(1)
πππ(πβ1)
ππβ
π(πβ1)
ππ
π¦πβ π¦π
) ,
π(π)
ππ= β
ππ¦
β
π=1,π ΜΈ=π
π(π)
ππ
π, π = 1, 2, . . . , ππ¦; π = 2, 3, . . . , π
π¦β 1, π ΜΈ= π.
(A.3)
The coefficients πΌ0, π½π, πΎπ, πΌ0, π½π, and πΎ
π, in (25) and (26),
are defined as
πΌ0= π(1)
ππ₯,2β π(1)
1,ππ₯β1β π(1)
1,2β π(1)
ππ₯ ,ππ₯β1,
π½π= π(1)
1,πβ π(1)
ππ₯,ππ₯β1β π(1)
1,ππ₯β1β π(1)
ππ₯,π,
πΎπ= π(1)
1,2β π(1)
ππ₯,πβ π(1)
1,πβ π(1)
ππ₯,2,
πΌ0= π(1)
ππ¦,2β π(1)
1,ππ¦β1β π(1)
1,2β π(1)
ππ¦,ππ¦β1,
π½π= π(1)
1,πβ π(1)
ππ¦ ,ππ¦β1β π(1)
1,ππ¦β1β π(1)
ππ¦,π,
πΎπ= π(1)
1,2β π(1)
ππ¦ ,πβ π(1)
1,πβ π(1)
ππ¦,2.
(A.4)
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper.
Acknowledgments
The authors would like to express their sincere appreciationfor the financial support from the Regional Council ofVaΜsterbotten, the County Administrative Board in Nor-rbotten, and The European Unionβs Structural Funds, TheRegional Fund.
References
[1] B. Budiansky and R. W. Connor, βBuckling stresses of clampedrectangular flat plates in shear,β Tech Note 1559, NACA, 1948.
[2] D. J. Johns, βShear buckling of isotropic and orthotropic plates:a review,β Aeronautical Research Council Report, Ministry ofDefense, HMSO, London, UK, 1971.
[3] D. Hui, βShear buckling of anti-symmetric cross ply rectangularplates,β Fibre Science and Technology, vol. 21, no. 4, pp. 327β340,1984.
[4] S. Kosteletos, βShear buckling response of laminated plates,βComposite Structures, vol. 20, no. 3, pp. 147β154, 1992.
[5] S. B. Biggers and S. S. Pageau, βShear buckling response oftailored composite plates,βAIAA Journal, vol. 32, no. 5, pp. 1100β1103, 1994.
[6] Y. Xiang, C. M. Wang, and S. Kitipornchai, βShear buckling ofsimply supported skew mindlin plates,β AIAA Journal, vol. 33,no. 2, pp. 377β378, 1995.
[7] J. Loughlan, βThe shear buckling behaviour of thin compositeplates with particular reference to the effects of bend-twistcoupling,β International Journal of Mechanical Sciences, vol. 43,no. 3, pp. 771β792, 2001.
[8] A. V. Lopatin and Y. B. Korbut, βBuckling of clampedorthotropic plate in shear,βComposite Structures, vol. 76, no. 1-2,pp. 94β98, 2006.
[9] I. Shufrin and M. Eisenberger, βShear buckling of thin plateswith constant in-plane stresses,β International Journal of Struc-tural Stability and Dynamics, vol. 7, no. 2, pp. 179β192, 2007.
[10] L. Papadopoulos and C. Kassapoglou, βShear buckling ofrectangular composite plates composed of concentric layups,β
-
Mathematical Problems in Engineering 11
Composites Part A: Applied Science and Manufacturing, vol. 38,no. 5, pp. 1425β1430, 2007.
[11] L.-Y. Wu, C.-H. Wu, and H.-H. Huang, βShear buckling ofthin plates using the spline collocation method,β InternationalJournal of Structural Stability and Dynamics, vol. 8, no. 4, pp.645β664, 2008.
[12] B. Uymaz andM. Aydogdu, βThree dimensional shear bucklingof FG plates with various boundary conditions,β CompositeStructures, vol. 96, pp. 670β682, 2013.
[13] M. Shariyat and K. Asemi, βThree-dimensional non-linearelasticity-based 3D cubic B-spline finite element shear bucklinganalysis of rectangular orthotropic FGM plates surrounded byelastic foundations,β Composites Part B: Engineering, vol. 56, pp.934β947, 2014.
[14] S. P. Timoshenko and J. M. Gere, Theory of Elastic Stability,International Student Edition, McGraw-Hill, 2nd edition, 1961.
[15] OΜ. Civalek, βApplication of differential quadrature (DQ) andharmonic differential quadrature (HDQ) for buckling analysisof thin isotropic plates and elastic columns,β Engineering Struc-tures, vol. 26, no. 2, pp. 171β186, 2004.
[16] A. N. Sherbourne and M. D. Pandey, βDifferential quadraturemethod in the buckling analysis of beams and composite plates,βComputers and Structures, vol. 40, no. 4, pp. 903β913, 1991.
[17] OΜ. Civalek, βFree vibration and buckling analyses of compositeplates with straight-sided quadrilateral domain based on DSCapproach,β Finite Elements in Analysis and Design, vol. 43, no.13, pp. 1013β1022, 2007.
[18] X. Wang, L. Gan, and Y. Zhang, βDifferential quadratureanalysis of the buckling of thin rectangular plates with cosine-distributed compressive loads on two opposite sides,β Advancesin Engineering Software, vol. 39, no. 6, pp. 497β504, 2008.
[19] C. Shu, Differential Quadrature and Its Application in Engineer-ing, Springer, London, UK, 2000.
[20] C. Shu and H. Du, βImplementation of clamped and simplysupported boundary conditions in the GDQ free vibrationanalysis of beams and plates,β International Journal of Solids andStructures, vol. 34, no. 7, pp. 819β835, 1997.
-
Submit your manuscripts athttp://www.hindawi.com
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Mathematical Problems in Engineering
Hindawi Publishing Corporationhttp://www.hindawi.com
Differential EquationsInternational Journal of
Volume 2014
Applied MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Probability and StatisticsHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Mathematical PhysicsAdvances in
Complex AnalysisJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
OptimizationJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
CombinatoricsHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Operations ResearchAdvances in
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Function Spaces
Abstract and Applied AnalysisHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of Mathematics and Mathematical Sciences
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Algebra
Discrete Dynamics in Nature and Society
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Decision SciencesAdvances in
Discrete MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com
Volume 2014 Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Stochastic AnalysisInternational Journal of