Research Article Dynamic Modeling and Vibration Analysis ...
Transcript of Research Article Dynamic Modeling and Vibration Analysis ...
Research ArticleDynamic Modeling and Vibration Analysis for the Vehicles withRigid Wheels Based on Wheel-Terrain Interaction Mechanics
Jianfeng Wang,1,2 Yiqun Liu,1 Liang Ding,1 Bing Yan,3 Haibo Gao,1 Baoyu Song,1 Tie Gao,2
Yuzhou Hao,1 and Mingdi Sun2
1State Key Laboratory of Robotics and System, Harbin Institute of Technology, Harbin 150001, China2School of Automotive Engineering, Harbin Institute of Technology, Weihai, Shandong 264209, China3Beijing Institute of Astronautical Systems Engineering, Beijing 100076, China
Correspondence should be addressed to Liang Ding; [email protected]
Received 31 August 2014; Revised 16 February 2015; Accepted 16 February 2015
Academic Editor: Sakdirat Kaewunruen
Copyright ยฉ 2015 Jianfeng Wang et al. This is an open access article distributed under the Creative Commons Attribution License,which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
The contact mechanics for a rigid wheel and deformable terrain are complicated owing to the rigid flexible coupling characteristics.Bekkerโs equations are used as the basis to establish the equations of the sinking rolling wheel, to vertical load pressure relationship.Since vehicle movement on the Moon is a complex and on-going problem, the researcher is poised to simplify this problem ofvertical loading of the wheel. In this paper, the quarter kinetic models of a manned lunar rover, which are both based on the rigidroad and deformable lunar terrain, are used as the simulation models. With these kinetic models, the vibration simulations wereconducted. The simulation results indicate that the quarter kinetic model based on the deformable lunar terrain accurately reflectsthe deformable terrainโs influence on the vibration characteristics of a manned lunar rover. Additionally, with the quarter kineticmodel of the deformable terrain, the vibration simulations of a manned lunar rover were conducted, which include a parametricanalysis of the wheel parameters, vehicle speed, and suspension parameters. The results show that a manned lunar rover requires alower damping value and stiffness to achieve better vibration performance.
1. Introduction
As a part of the deep space detection project of China,astronauts will land on the Moon from 2020 to 2030 toestablish the lunar observation station and to detect availablemineral resources, which will be used to build the basicfacilities for further lunar exploration [1]. For the mannedlunar-landing project, the vehicle plays a key role, in makingit possible for the astronauts to complete long distanceexploration tasks with heavy equipment and to transportsamples back. Until now, the manned lunar rover vehiclesbelonging to the Project Apollo have been the main mannedvehicle that has landed on the Moon and completed seriousexploration [2, 3]. However, with the limitations of researchconditions, the studies of the American manned lunar roverare not perfect.
Given the enormous value of a manned lunar rover forlanding and exploration, the development of new mannedlunar rovers is rapidly occurring around theworld. Until now,
a number of manned lunar rovers with different conceptshave been designed and manufactured globally. Among theperformance considerations of themanned lunar rovers, boththe vibration performance and the ride comfort are essential.
At present, some researchers have studied the vibration ofthe lunar rover. Gao et al. established a vibration model withseven degrees of freedom for a planetary-wheel lunar roverand optimized the choice of suspension spring stiffness anddamping value [4]. At the same time, the authors proposed arevised method for equivalent surface roughness functions.In addition, this work established a kinetic model with 11degrees of freedom for a six-wheeled, rocker-style lunar roverto analyze the ride comfort. X.-L. Wang and R.-B. Wangbuilt a rigid-elastic coupling model for the lunar rover anddetermined the resonance frequency area by simulating thesurface roughness of the lunar terrain [5].
Considering the characteristics of a manned lunar roverand the contact model of the wheel and terrain, this paper
Hindawi Publishing CorporationShock and VibrationVolume 2015, Article ID 751890, 9 pageshttp://dx.doi.org/10.1155/2015/751890
2 Shock and Vibration
V
W
z
๐๐
Figure 1: Bekkerโs contact model.
establishes a quarter kineticmodel and analyzes the influenceof wheel size on the vibration performance.
In this paper, the contact model of a rigid wheel andlunar terrain is established based on Bekkerโs equations [6, 7].Moreover, the quarter kinetic model of a manned lunar roveris established, which is used to study the influence of wheelparameters, suspension parameters, and vehicle speed on thevibration performance.
2. Lunar Terrain Model
Lunar terrain is similar to the sandy environment of the Earthwith the addition of a variety of different-size meteoritesdistributed on the lunar surface [8, 9]. Therefore, the lunarterrain will cause vibrations of a manned lunar rover when itis moving on the lunar surface. Additionally, wheels on thelunar terrain will sink because of the plastic deformation andelastic deformation of the terrain under the normal pressureof the wheel. The contact model between the wheel and thelunar terrain is a very complex, nonlinear contact model.
For the analysis of the contact model between thewheel and lunar terrain, three effective methods include thesemiempirical method, finite element method, and analyticalmethod [10โ12]. Given the characters of a manned lunarrover, the semiempirical method is applied. Figure 1 showsthe relationship of the normal stress and the wheel sinkagein Bekkerโs model; the following describes the contact model[7, 11]:
๐ = (
๐๐
๐
+ ๐๐) โ ๐ง๐
. (1)
The variables are defined as follows: ๐ (Pa) is the meannormal stress under the plate, ๐ (m) is the short-edge lengthor the radius of plate, ๐ (dimensionless) is the sinkageexponent of the terrain, ๐ง (m) is the wheel sinkage, ๐
๐
(Pa/m๐โ1) is the cohesive modulus of the terrain in Bekkerโsmodel, and ๐
๐(Pa/m๐) is the frictionalmodulus of the terrain
in Bekkerโs model. For the study in this paper, the ๐๐=
1.4Pa/m๐โ1 and the ๐๐= 820 kPa/m๐โ1 [13].
When driving a manned lunar rover, the wheel drivingforce is mainly provided by the shear stress between thewheel and the lunar terrain. The shear performance of thelunar terrain is shown with the shear force versus shear
WT
fDP
๐๐
๐
๐(๐) ๐(๐)
๐1๐2
๐M
z2z
Figure 2: Wheel-soil interaction mechanics model.
displacement diagram. Based on Janosiโs terrain shearingmodel [14], the relationship of the terrain shear stress andshear displacement is described by
๐ = ๐max (1 โ ๐โ๐/๐0
) = (๐ + ๐ tan๐) (1 โ ๐โ๐/๐0) . (2)
The variables are defined as follows: ๐ (Pa) is the cohesionof the terrain, ๐ (โ) is the internal friction angle of the terrain,๐ (m) is the shear displacement of the terrain, and ๐
0is
the shear deformation modulus of the terrain. For the lunarterrain, the value of ๐ is in the range of 0.1 kPa to 2.5 kPa, and๐ is in the range of 25 to 50 degrees [13].
3. Wheel-Terrain Interaction Mechanics Model
For amovingmanned lunar rover, the wheels mainly bear thevertical force and longitudinal force. Figure 2 shows the stressdistribution of a spinning wheel. The variables are defined asfollows: ๐ (N โ m) is the driven torque of the wheel, ๐DP (N) isthe horizontal resistance force,๐ (N) is the vertical load, ๐
1
(โ) is the entrance angle of the wheel moving on the terrain,๐2(โ) is the leaving angle of the wheel moving on the terrain,
and ๐๐
(โ) is the angular position of the maximum stress ofthe terrain acting on wheel.
As shown in Figure 2, the force balance consists of a stresssystem including the shearing force, the normal force, driventorque, the horizontal resistance, and the vertical load force.The normal stress and the shear stress change with both theentrance angle and leaving angle of the wheel moving on theterrain.
Lunar terrain is a type of elastic-plastic soil. Therefore,the wheel sinkage happens under the effect of lunar gravityand vertical vibration. The wheel sinkage is determined bythe geometric parameters in Figure 2, and the relationship isshown in (3). In addition, the shear deformation, which is
Shock and Vibration 3
caused by the slipping between the wheel and the terrain, isdescribed by [15]
๐ง = ๐ (1 โ cos ๐1) , (3)
๐ = ๐ ((๐1โ ๐) โ (1 โ ๐ ) (sin ๐
1โ sin ๐)) . (4)
The variables are defined as follows: ๐ง (m) is the depthof the wheel sinkage, and also is the distance from the lowof wheel to the ground. ๐ (m) is the wheel radius, and ๐
(dimensionless) is the slip ratio of the wheel.When the wheel is in the static state, the normal stress
under the wheel is symmetrically distributed, and the max-imum stress occurs at the bottom-dead-center. If the wheelis in the rolling state, the maximum stress is in the frontpart of the wheel, which is caused by the wheel slipping.The following shows that the location of the maximum shearstress and normal stress on the wheel are coefficients of thewheel-soil interaction angel (dimensionless):
๐๐= (๐1+ ๐2|๐ |) ๐1. (5)
The normal and shear stress distribution equations of theWong-Reecemodel are shown by (6) and (7), respectively [15,16]. Consider the following:
๐1(๐) = (
๐๐
๐
+ ๐๐) ๐๐
(cos ๐ โ cos ๐1)๐
, (๐๐โค ๐ โค ๐
1) ,
๐2(๐) = (
๐๐
๐
+ ๐๐) ๐๐
[cos(๐1โ
๐ โ ๐2
๐๐โ ๐2
ร (๐1โ ๐๐))
โ cos ๐1]
๐
, (๐2โค ๐ < ๐
๐) ,
(6)
๐1(๐) = [๐ + ๐
1(๐) tan๐] (1 โ exp(โ
๐
๐0
)) ,
(๐๐โค ๐ โค ๐
1) ,
๐2(๐) = [๐ + ๐
2(๐) tan๐] (1 โ exp(โ
๐
๐0
)) ,
(๐2โค ๐ โค ๐
๐) .
(7)
As Figure 2 demonstrated, the vertical load on the wheelfrom the terrain consists of the vertical component of thenormal stress and the vertical component of the shear stress.From this, the vertical load on the wheel can be obtained by(8). In this equation, ๐ (m) is the width of the wheel:
๐ = ๐๐โซ
๐1
๐2
(๐ (๐) cos (๐) + ๐ (๐) sin (๐)) ๐๐. (8)
In order to achieve sufficient driving forces, lugs are addedto the rigid wheel to provide a larger shear force for themanned lunar rover. The contact model of the lunar terrainand rigid wheel with lugs is complicated; therefore, this paperdoes not consider the lugs. This paper mainly studies thesmooth rigid wheel and the vertical load. According to our
previous research [16, 17], the shear stress of the smooth rigidwheel has almost no influence on the vertical load, and, thus,it can be ignored. Simplifying the equation for the verticalload, we can write
๐ โ ๐๐โซ
๐1
๐2
๐ (๐) cos (๐) ๐๐
= ๐๐(โซ
๐๐
๐2
๐1(๐) cos (๐) ๐๐ + โซ
๐1
๐๐
๐2(๐) cos (๐) ๐๐) .
(9)
Equation (9) is a complex, nonlinear equation. Janosi etal. describe a method that has simplified (9) [14]. In thiswork, they describe ๐
๐= ๐๐ ๐๐
(cos ๐๐โ cos ๐
1)๐, where the
variable ๐๐ (dimensionless) is the equivalent sinkagemodulus
of the terrain, defined as ๐๐ = ๐๐/๐ + ๐
๐. Equation (10) shows
the simplified result of (6) [17]. Consider the following:
๐1(๐) โ ๐
๐ฟ
1(๐) =
๐๐(๐1โ ๐)
(๐1โ ๐๐)
(๐๐โค ๐ โค ๐
1) ,
๐2(๐) โ ๐
๐ฟ
2(๐) =
๐๐(๐ โ ๐
2)
(๐๐โ ๐2)
(๐2โค ๐ < ๐
๐) .
(10)
By substituting (10) into (9), we obtain
๐ =
2๐๐๐๐(1 โ cos ๐
1)
๐1
=
2๐๐ง๐๐
๐1
=
2๐๐๐ ๐ง๐+1
๐1
. (11)
The entrance angle of amanned lunar rover wheel is smalland changes with a change in the depth of the wheel sinkageand the slip angle. The wheel entrance angle is describes by
๐1= โ
2๐ง
๐
. (12)
Substituting (12) into (1) produces [17]
๐ =
2๐๐๐ ๐ง๐+1
๐1
โ โ2๐๐๐๐ ๐ง๐+1/2
. (13)
4. Kinetic Model of a Manned Lunar Rover
The quarter kinetic model is an efficient method to study thevibration performance of a moving manned lunar rover. Theassumptions of the quarter kinetic model are that the wheelis a single rigid body, only vertical vibration occurs, and thewheel must be in contact with the terrain.
4.1. Kinetic Model of a Manned Lunar Rover on a Rigid Road.In the studies of traditional vehicles, the deformation ofthe road surface is not taken into consideration in dynamicperformance, and the contact point is considered as a typeof effective simplified model for the contact area of thewheel and road. First, the quarter kinetic model of a mannedlunar rover on a nondeformable road was built as shown inFigure 3. The kinetic equations are described by
๐1๏ฟฝ๏ฟฝ1+ ๐ (๏ฟฝ๏ฟฝ
1โ ๏ฟฝ๏ฟฝ2) + ๐ (๐ง
1โ ๐ง2) = 0,
๐2๏ฟฝ๏ฟฝ2+ ๐ (๏ฟฝ๏ฟฝ
2โ ๏ฟฝ๏ฟฝ1) + ๐ (๐ง
2โ ๐ง1) = 0.
(14)
4 Shock and Vibration
k c
m1
m2
z1
z2zg
Figure 3: The quarter kinetic model of a manned lunar rover on arigid road.
k c
m1
m2
z1
z2
zg
Figure 4: The quarter kinetic model of a manned lunar rover on adeformable terrain.
The variables are defined as follows: ๐1(kg) is the
sprung mass, ๐2(kg) is the unsprung mass, ๐ (kN/m) is the
suspension stiffness, ๐ (kN/(m/s)) is the damping coefficientof the suspension, ๐ง
1(m) is the deformation of the sprung
mass, ๐ง2(m) is the deformation of the unsprungmass, and ๐ง
๐
(m) is the deformation of the ground.
4.2. Kinetic Model of a Manned Lunar Rover on a DeformableTerrain. The lunar terrain will sink when in contact withthe rigid wheel, which will press the wheel surface as seenin Figure 2. Figure 4 depicts the kinetic model of a mannedlunar rover on a deformable terrain. The definition of thevariables is the same as those in Figure 3. The kineticequations are described by
๐1๏ฟฝ๏ฟฝ1+ ๐ (๏ฟฝ๏ฟฝ
1โ ๏ฟฝ๏ฟฝ2) + ๐ (๐ง
1โ ๐ง2) = 0,
๐2๏ฟฝ๏ฟฝ2+ ๐ (๏ฟฝ๏ฟฝ
2โ ๏ฟฝ๏ฟฝ1) + ๐ (๐ง
2โ ๐ง1) = ฮ๐น
๐.
(15)
In (15), ฮ๐น๐(N) is the vertical load on the wheel, which
comes from the terrain, and is equal to ๐ (N). Combiningthis equation with (13) results in
ฮ๐น๐= ๐ = โ2๐๐๐
๐ ๐ง๐+1/2
. (16)
For (16), the sinkage exponent of the terrain relates tothe slip ratio. According the study of Ding et al. [16, 17], thesinkage exponent of the terrain can be treated as linear. Inthis case, the sinkage exponent is constant at ๐ = 1. Then, thevertical deformation of the rigid wheel mainly relates to theroughness of the lunar terrain.
5. Surface Unevenness Simulation ofthe Lunar Terrain
Since there are few studies on the surface roughness of thelunar terrain, the recent topography and geomorphologyare mainly at the kilometer level. Obviously, the size ofthe manned lunar rover has warranted the need for surfaceunevenness data at the meter level. The surface roughnessmodel was built based on the expressive method of roadroughness for traditional vehicles.The power spectral density(PSD) expression of the lunar terrain surface unevenness isdefined by [18]
๐บ๐(๐) = ๐บ
๐(๐0) โ (
๐
๐0
)
โ๐ค
, (๐ > 0) . (17)
The variables are defined as follows: ๐0is the reference
frequency, ๐บ๐(๐0) is the coefficient of the road roughness,
๐บ๐(๐) is the road roughness, and๐ค is the frequency exponent
that is experientially determined to be 2.The method used to filter white noise is a type of road
roughness reconstruction method, which has a high simula-tion precision [18].The road roughness equation constructedby this model is descried by.
๐ (๐ก) = 2๐๐0๐ (๐ก) = 2๐๐
0โ๐บ๐ (๐
0) V๐ค (๐ก) . (18)
The variables are defined as follows:๐0is the lower cut-off
frequency of the filter, ๐(๐ก) is the surface roughness amplitudeof a random road, and ๐ค(๐ก) is the uniformly distributed unitof white noise with an average value of 0 and intensity of 1.
6. Simulation and Analysis
Table 1 displays the vehicle parameters before the simulation.In the Chinese lunar exploration project [19], the mannedlunar rover should transport two astronauts, and the com-bined weight is 660 kg. Obviously, the wheel size has a vastinfluence on the mechanical properties. Referencing the sizeof the current lunar rover wheels, the width ranges from100mm to 300mm, and the radius ranges from 200mmto 500mm. Therefore, the wheel width was chosen to be230mm, and the radius was chosen to be 410mm. Thevelocity of the lunar rover ranges from 5 km/h to 18 km/h.In this study, the velocity used was 10 km/h. Table 1 contains
Shock and Vibration 5
Table 1: Parameters of the manned lunar rover used for thesimulations.
Number Parameter Value1 Wheel radius 410mm2 Wheel width 230mm3 Sprung mass 150 kg4 Unsprung mass 15 kg5 Suspension stiffness 6260N/m6 Suspension damper 5753Nโ s/m
the parameters of the manned lunar rover used in oursimulations.
In order to investigate the vibration performance of amanned lunar rover on both rigid road and deformableterrain, the kinetic models were simulated using (14) and(15), respectively. The PSD of the rigid road and deformableterrain was based on the road roughness of level E road fora traditional vehicle, which is shown in Figure 5. Figure 6shows that the vertical vibration acceleration of the lunarrover on the rigid road is much greater than that on thedeformable terrain. When the lunar rover moves on the rigidroad, the surface roughness transferred to the wheel directly,creating a vigorous vibration. However, once the lunar rovermoved on the deformable terrain, the terrain sinkage absorbsthe energy of the vibration, as it plays the role of a damper.On the Moon, most of the area is elastic-plastic terrain withfew areas covered bymeteorites of varying size.Therefore, thekinetic model of the lunar rover on the deformable terrainis more suitable to study the vibration performance of themanned lunar rover.
Through the wheel, themanned lunar rover and the lunarterrain interact. The parameters of the wheel affect not onlythe drive performance, but also the vibration performance ofthe manned lunar rover. Figure 6 shows the acceleration anddisplacement of the sprung mass of the lunar rover with dif-ferent wheel radii. The acceleration and displacement of thesprung mass decreased with a decrease in road deformation.The vibration acceleration was at a minimumwhen the wheelradius was 0.15m and increasedwith increasing wheel radius.
Figure 7 shows the acceleration of the manned lunarrover with different wheel widths. The wheel width had aconsiderable influence on the acceleration of the sprungmass.When the vibration acceleration was low, the wider wheelweakened the vibration; however, when the acceleration washigh, the wider wheel enhanced the vibration.
Figure 8 shows the acceleration and displacement ofthe manned lunar rover sprung mass with different vehiclevelocities. We observe that the vehicle velocity has littleinfluence on the acceleration but shows obvious effects onthe displacement. With an increase of vehicle velocity, thedisplacement of the sprung mass decreased gradually, whichwas a result of minor changes in the acceleration of thesprungmass under different vehicle velocities. Higher vehiclevelocities correlated with decreased response times of thesprung mass, which led to a reduction of the displacementof the sprung mass.
0 10 20 30 40โ15
โ10
โ5
0
5
10
15
Time (s)
Rigid roadDeformable road
Body
acce
lera
tion
(m/s2)
Figure 5: Comparison between the kinetic models of the rigid roadand deformable terrain.
0 10 20 30 40โ5
0
5
Time (s)
Body
acce
lera
tion
(m/s2)
r = 0.15mr = 0.35mr = 0.55m
Figure 6: Acceleration of the sprung mass of different wheel radii.
The acceleration and displacement of the sprung massof the manned lunar rover with different stiffnesses aredisplayed in Figure 9. The vibration variables indicatedminor changes when the suspension stiffness changed from3000N/m to 9000N/m. However, when the suspension stiff-ness changed from6000N/m to 60000N/m, obvious changesin vibration were observed. At a high stiffness, the sprungmass vibrated violently, indicating reduced ride comfort.
The damping coefficient also had a considerable effecton the vibration performance, as shown in Figure 10. Theacceleration is damped quickly at high suspension dampingcoefficients because a damperwith a high damping coefficientmore quickly absorbs the energy of vibrations. However, oncethe road simulation amplitude increased, the acceleration
6 Shock and Vibration
0 10 20 30 40โ5
โ4
โ3
โ2
โ1
0
1
2
3
4
5
Time (s)
Body
acce
lera
tion
(m/s2)
b = 0.1mb = 0.23mb = 0.35m
(a)
0 10 20 30 40
Body
pos
ition
(m)
Time (s)
b = 0.1mb = 0.23mb = 0.35m
0.3
0.2
0.1
0
โ0.1
โ0.2
โ0.3
โ0.4
(b)
Figure 7: Acceleration and displacement of the sprung mass with different wheel widths.
0 10 20 30 40โ5
โ4
โ3
โ2
โ1
0
1
2
3
4
5
Time (s)
Body
acce
lera
tion
(m/s2)
๏ฟฝ = 1.5m/s๏ฟฝ = 2.78m/s๏ฟฝ = 3.5m/s
(a)
0 10 20 30 40
Body
pos
ition
(m)
Time (s)
๏ฟฝ = 1.5m/s๏ฟฝ = 2.78m/s๏ฟฝ = 3.5m/s
0.3
0.2
0.1
0
โ0.1
โ0.2
โ0.3
โ0.4
(b)
Figure 8: Acceleration and displacement of the sprung mass with different vehicle velocities.
increased as well.Therefore, too high of a damping coefficientis not beneficial to the ride comfort of a manned lunar rover.
7. Conclusions
(1) The quarter kinetic model of a manned lunar rovercan adequately simulate the vibration performance ofthe vehicle. When the manned lunar rover was on thedeformable terrain, the vibration performance was
greatly affected by the stress between the wheel andterrain. Note that the quarter kinetic model can beused only under the condition that the wheels main-tain contact with the terrain. Further investigation isneeded for the vibration performance when the wheelloses contact with the terrain.
(2) The wheel size of the manned lunar rover affectedthe vibration of the sprung mass. A bigger wheel
Shock and Vibration 7
0 10 20 30 40โ6
โ4
โ2
0
2
4
6
Time (s)
Body
acce
lera
tion
(m/s2)
k = 3000N/mk = 6000N/mk = 9000N/m
(a)
0 10 20 30 40
Body
pos
ition
(m)
Time (s)
0.3
0.2
0.1
0
โ0.1
โ0.2
โ0.3
โ0.4
k = 3000N/mk = 6000N/mk = 9000N/m
(b)
0 10 20 30 40โ6
โ4
โ2
0
2
4
6
Time (s)
Body
acce
lera
tion
(m/s2)
k = 6000N/mk = 30000N/mk = 60000N/m
(c)
0 10 20 30 40Time (s)
k = 6000N/mk = 30000N/mk = 60000N/m
Body
pos
ition
(m)
0.3
0.2
0.1
0
โ0.1
โ0.2
โ0.3
โ0.4
(d)
Figure 9: Acceleration and displacement of the sprung mass with different suspension stiffnesses.
radius correlated with better obstacle-climbing per-formance, but also a higher acceleration of the sprungmass. In addition, the influence of the wheel widthon the vibration performance was found to be com-plicated, though mainly determined by the surfaceroughness of the lunar terrain. On a gentle road,a wider wheel decreased the vibration acceleration.While on a bumpy road, a wider wheel increased thevibration acceleration.
(3) The vehicle velocity had little influence on the vibra-tion acceleration but obvious effects on the vibra-tion displacement of the sprung mass of a mannedlunar rover. With an increase in vehicle velocity, thedisplacement of the sprung mass decreased. This is
because a high velocity shortens the action time of theacceleration, which changes minimally with differentvelocities, causing a decrease in the displacement ofthe sprung mass.
(4) The suspension conditions included the stiffness anddamping value. Lower stiffness indicated lower vibra-tion. Obviously, the vibration parameters were equalwhen the stiffness ranged over a small scale. Asopposed to the suspension stiffness, the variation inthe suspension damping value can greatly affect thevibration performance. At a high damping value, thesuspension was able to absorb the vibration energyon a massive scale but could not effectively decreasethe vibration acceleration amplitude. On the contrary,
8 Shock and Vibration
0 10 20 30 40โ8
โ6
โ4
โ2
0
2
4
6
8
Time (s)
Body
acce
lera
tion
(m/s2)
c = 3000Ns/mc = 10000Ns/mc = 50000Ns/m
(a)
0 10 20 30 40Time (s)
c = 3000Ns/mc = 10000Ns/mc = 50000Ns/m
Body
pos
ition
(m)
0.3
0.2
0.1
0
โ0.1
โ0.2
โ0.3
โ0.4
(b)
Figure 10: Acceleration and displacement of the sprung mass with different suspension damping values.
at a low damping value, the suspension could notabsorb the vibration energy effectively. Generally, thechoice of the damping value should consider variousperformance conditions of the manned lunar rover.
(5) In this paper, the shear force between the wheeland terrain was ignored. The vertical componentof the shear force had a considerable effect on thevertical load when the lunar rover required a largedriving force, which greatly affected the vibrationperformance.
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper.
Acknowledgments
This study was supported in part by the National NaturalScience Foundation of China (Grant no. 61370033/51275106),National Basic Research Program of China (Grant no.2013CB035502), the Fundamental Research Funds for theCentral Universities (Grant no. HIT.BRETIII.201411), S&TInnovation Project of CASC-HIT S&T Innovation Center(Grant no. CASC-HIT11-1A03), Foundation of Chinese StateKey Laboratory of Robotics and Systems (Grant No. SKLRS-2014-MS-09), and the โ111 Projectโ (Grant no. B07018).
References
[1] L. Long, โOn issues of China manned lunar exploration,โMissiles and Space Vehicles, no. 6, pp. 1โ5, 2010.
[2] R. D. Launius, โProject Apollo in Americanmemory andmyth,โinProceedings of the 7th International Conference and Expositionon Engineering, Construction, Operations and Business in Space,pp. 1โ13, March 2000.
[3] M. R. Grabois, โApollo: Learning from the past, for the future,โActa Astronautica, vol. 68, no. 7-8, pp. 1353โ1360, 2011.
[4] H.-B. Gao, Q.-X. Meng, Z.-Q. Deng, H.-T. Fang, J.-G. Tao,and M. Hu, โAnalysis of dynamic load between wheels of theplanetary wheel lunar rover and ground,โ Journal of HarbinInstitute of Technology, vol. 38, no. 4, pp. 523โ527, 2006.
[5] X.-L. Wang and R.-B. Wang, โAnalysis of lunar rover vibrationcharacteristics based on rigid-flexible coupled model,โ Journalof Jilin University (Engineering and Technology Edition), vol. 42,no. 2, pp. 279โ284, 2012.
[6] M. G. Bekker,Theory of Land Locomotion, University of Michi-gan Press, Ann Arbor, Mich, USA, 1956.
[7] M. G. Bekker, Introduction to Terrain-Vehicle Systems, Univer-sity of Michigan Press, Ann Arbor, Ill, USA, 1969.
[8] Y. Zhao, H. S. Lv, L. Li, L. Guo, and M. Zhang, โLunar terrainconstruction and application for Lunar Rover,โ InformationTechnology Journal, vol. 12, no. 23, pp. 7201โ7207, 2013.
[9] Q. Su, Y. Zhao, K. Yang, and S. Zhang, โLunar terrain andmineralโs abundance automatic analysis,โ Optik, vol. 125, no. 3,pp. 1278โ1282, 2014.
[10] S. Park, A. A. Popov, and D. J. Cole, โInfluence of soil deforma-tion on off-road heavy vehicle suspension vibration,โ Journal ofTerramechanics, vol. 41, no. 1, pp. 41โ68, 2004.
[11] G. Grant, L. Sean, andG. Richard, โOff-road vehicle locomotionusing Bekkerโs model,โ in The International Society for OpticalEngineering, vol. 4024 of Proceedings of SPIE, pp. 127โ136, 2000.
[12] G. Michel and C. Edouard, โA new soil-vehicle interactionmodel for predicting off road mobility performances,โ in Pro-ceedings of the 16th International Conference of the InternationalSociety for Terrain Vehicle Systems (ISTVS โ08), pp. 108โ113,Turin, Italy, November 2008.
Shock and Vibration 9
[13] L. Ding, H. Gao, Z. Deng, L. Xiong, J. Guo, and Y. Lu,โAn approach of identifying mechanical parameters for lunarsoil based on integrated wheel-soil interaction terramechanicsmodel of rovers,โ Acta Aeronautica et Astronautica Sinica, vol.32, no. 6, pp. 1112โ1123, 2011.
[14] Z. J. Janosi, R. A. Liston, L. A. Martin et al., โCommercial off-road vehicles,โ in Proceedings of the Automotive EngineeringCongress, SAE International, Detroit, Mich, USA, January 1970.
[15] J.-Y. Wong and A. R. Reece, โPrediction of rigid wheel per-formance based on the analysis of soil-wheel stresses part I.Performance of driven rigid wheels,โ Journal of Terramechanics,vol. 4, no. 1, pp. 81โ98, 1967.
[16] L. Ding, H.-B. Gao, Z.-Q. Deng, J.-G. Tao, and L.-B. Xiong,โWheel-soil interaction mechanics model for lunar rover:decoupling and application,โ Journal of Harbin Institute ofTechnology, vol. 43, no. 1, pp. 56โ61, 2011.
[17] L. Ding, H. Gao, Y. Li, G. Liu, and Z. Deng, โImproved explicit-form equations for estimating dynamic wheel sinkage andcompaction resistance on deformable terrain,โ Mechanism andMachine Theory, vol. 86, pp. 235โ264, 2015.
[18] Y.Wang, Ch. Li, and Z.Ma, โSimulation on vehicle ride comfortbased onADAMS/Cars ride,โMachineryDesign&Manufacture,no. 4, pp. 81โ82, 2010.
[19] Z.-Q. Deng, X.-B. Fan, H.-B. Gao, and L. Ding, โReview andkey techniques for locomotive system of manned lunar rovers,โJournal of Astronautics, vol. 33, no. 6, pp. 675โ689, 2012.
International Journal of
AerospaceEngineeringHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
RoboticsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Active and Passive Electronic Components
Control Scienceand Engineering
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
RotatingMachinery
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporation http://www.hindawi.com
Journal ofEngineeringVolume 2014
Submit your manuscripts athttp://www.hindawi.com
VLSI Design
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Shock and Vibration
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Civil EngineeringAdvances in
Acoustics and VibrationAdvances in
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Electrical and Computer Engineering
Journal of
Advances inOptoElectronics
Hindawi Publishing Corporation http://www.hindawi.com
Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
SensorsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Modelling & Simulation in EngineeringHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Chemical EngineeringInternational Journal of Antennas and
Propagation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Navigation and Observation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
DistributedSensor Networks
International Journal of