RESEARCH AND DEVELOPMENT OF STEELHEAD TROUT …
Transcript of RESEARCH AND DEVELOPMENT OF STEELHEAD TROUT …
RESEARCH AND DEVELOPMENT OF STEELHEAD TROUT Oncorhynchus mykiss
AQUACULTURE IN SEA CAGES
BY
MICHAEL DAVID CHAMBERS
B.S., University of Wisconsin, 1985
M.S., Texas A&M University, 1994
DISSERTATION
Submitted to the University of New Hampshire
in Partial Fulfillment of
the Requirements for the Degree of
Doctor of Philosophy
in
Zoology
December, 2013
UMI Number: 3579692
All rights reserved
INFORMATION TO ALL USERS The quality of this reproduction is dependent upon the quality of the copy submitted.
In the unlikely event that the author did not send a complete manuscript and there are missing pages, these will be noted. Also, if material had to be removed,
a note will indicate the deletion.
UMIDissertation PiiblishMig
UMI 3579692Published by ProQuest LLC 2014. Copyright in the Dissertation held by the Author.
Microform Edition © ProQuest LLC.All rights reserved. This work is protected against
unauthorized copying under Title 17, United States Code.
ProQuest LLC 789 East Eisenhower Parkway
P.O. Box 1346 Ann Arbor, Ml 48106-1346
This dissertation has been examined and approved.
Dissertation Director, Dr. W. Huntting Howell, Professor of Zoology,University of New Hampshire
Dr. Winsor H. Watson III, Professor of Zoology, University of New Hampshire
Dr. Richard Langan,Affiliate Professor of Biological Sciences, University of New Hampshire
Dr. Ey^fyn S. Sawyer,President and CEO, Sea Run Holdings, Freeport, ME
________________
Dr. Tim Dempster,Senior Lecturer, Department of Zoology, University of Melbourne
/he 6. Zo/3Date
DEDICATION
This dissertation is dedicated to my family here in New Hampshire and in
Wisconsin. My accomplishments during this journey would never have been possible
without your patience, love and support. And to my father who taught me a very
important life lesson, once you start something, you must finish it!
ACKNOWLEDGMENTS
Where to begin? Let’s start with the UNH BSC staff that makes everything
possible. They provide us with P-cards for purchasing power, they set up PO’s for
contracting outside venders and they process time sheets so that students and SCUBA
divers could get paid on time. For this, I’m gratefully indebted to Meriel Bunker,
Theresa Hammer, Nancy Wallingford, Tammy McGlone and Patrice MacNevin.
The UNH OOA program created the impetus for my research. I’m appreciative to
all the hard working personnel over the years that made the project possible. The names
are too many to mention and would add another chapter to this thesis so I’ll settle for the
most recent crew associated with the research. This includes Captains Tim McClare and
Gita George, divers extraordinaire Elizabeth Kintzing, Rob Love, Gunnar Ek, Graham
McKay and Tom Langley.
I’m very thankful to the following: 1.) UNH Facility Managers David Shay, Noel
Carlson, Nate Rennels and Deb Lampson as well as staff members and students, Jessica
Cranney, Chris Rillahan, Jon Bunker, and James Quadrino for collecting, processing data,
constructing cage systems and maintaining experiments, 2.) Captains Bryan Soares and
Debra Brewitt for their patience in sharing pier space, the crane and playing musical
chairs with the cage frames as they were relocated to and from the pier, 3.) NH Sea
Grant team Jon Pennock, Ken LaValley (now Cooperative Extension) Sally Nelson,
Jennifer Bedsole, Eric Chapman, Sarah Redmond (ME Sea Grant), Steve Jones, Gabby
Bradt, Rebecca Zeiber, Steve Adams and Dari ward (especially in borrowing water
sampling equipment) for their tremendous support during the research efforts. 4.) Sumner
IV
Brook Trout farms (Dick and Jess Pemier) and Great Bay Aquaculture (George Nardi)
for supplying juvenile steelhead trout and cod for the experiments. 5.) Our Norwegian
counter parts Pal Lader, Arne Fredheim, Erik Hoy, Martin Fore, Heidi Moe and Kevan
Frank for their aquaculture collaborations and the 6.) UNH Ocean Engineering
Department Jud DeCew, Barbaras Celikkol, Ken Baldwin , Rob Swift, Igor Tsukrov for
their technology guidance with systems design and operation.
A special thanks to Hunt Howell for his patience, fortitude, guidance and
friendship. He made this remarkable journey possible and so will forever be indebted. To
my committee members Win Watson, Richard Langan, Evelyn Sawyer and Tim
Dempster for their wisdom and guidance throughout the dissertation process.
Funding agencies primarily responsible for the research was: 1.) the International
Copper Association, especially Hal Stillman and Robert Dwyer for their expert opinion
on copper alloy applications, 2.) Riverdale Mills for generously contributing the Seawire
netting that was expedited to UNH by Jeff Beaton and Larry Walsh for the spring 2010
experiment 3.) The Norway Research Council for funding the BELAT project (Chapter 2).
This was made possible through a joint partnership between UNH, SINTEF Fisheries and
Aquaculture, and AquaCulture Engineering in Trondheim, Norway, 4.) NOAA
Saltonstall Kennedy Program award Number NA10NMF4270213 for their support in the
submerged trout research (Chapter 3) and 5.) NH Sea Grant for their financial support in
my aquaculture extension activities (Chapter 4).
I also want to recognize UNH for the use of their facilities especially the Judd
Gregg Marine Research Facility Pier. The pier was the launching area for the studies and
provided research vessels and crane to safely deploy cage systems and fish.
V
Finally, I want to acknowledge my family for their remarkable patience and
support during this amazing journey. Hopefully now, the time taken from them working
late nights and weekends can be paid back in full.
VI
TABLE OF CONTENTS
DEDICATION....................................................................................................................... Ill
ACKNOWLEDEMENTS..................................................................................................... IV
LIST OF TABLES................................................................................................................XII
LIST OF FIGURES.............................................................................................................XIII
ABSTRACT........................................................................................................................XVI
CHAPTER PAGE
INTRODUCTION.................................................................................................................. 1
I. EFFECTS OF BIOFOULING ON COMPARATIVE GROWTH AND SURVIVAL OF
JUVENILE ATLANTIC COD Gadus morhua CULTUREED IN OCEAN PENS 6
Abstract....................................................................................................................... 6
Introduction................................................................................................................. 7
Materials and Methods.............................................................................................. 9
Cage design............................................................................................................9
Stocking and Feeding...........................................................................................10
Behavioral and Environmental Monitoring........................................................ 10
Data Collection..................................................................................................... 11
Results........................................................................................................................12
VII
Environmental 12
Cod Performance..................................................................................................12
Bio-fouling........................................................................................................... 13
Copper Content Analysis.................................................................................... 13
Discussion................................................................................................................. 14
Conclusion................................................................................................................ 16
II. FIELD MEASUREMENTS OF STEELHEAD TROUT Oncorhynchus mykiss
DISTRIBUTION, SWIMMING BEHAVIOR AND RESPONSE TO WATER
CURRENT EXPOSURE IN A SEA CAGE...................................................................... 23
Abstract..................................................................................................................... 23
Introduction...............................................................................................................24
Materials and Methods............................................................................................ 27
Location................................................................................................................ 27
Cage Design.........................................................................................................28
Environmental Data Collection...........................................................................28
Telemetry Set U p .................................................................................................29
Net Transmitters...................................................................................................30
Fish Transmitters..................................................................................................30
Data Processing and Statistics.............................................................................31
Net Transmitters............................................................................................. 31
Fish Transmitters............................................................................................ 31
Results....................................................................................................................... 33
Vlll
Environmental..................................................................................................... 33
Net Deformation.................................................................................................. 33
Fish Swimming Behavioral and Distribution.................................................... 34
Discussion.................................................................................................................35
III. SUBMERGED CULTURE OF STEELHEAD TROUT Oncorhynchus mykiss FOR
OPEN OCEAN AQUACULTURE IN THE NORTHEASTERN UNIITED STATES . 49
Abstract.....................................................................................................................49
Introduction...............................................................................................................50
Materials and Methods............................................................................................ 52
Timing and Locations.......................................................................................... 52
Steelhead Trout................................................................................................... 53
Experiment 1 ....................................................................................................... 54
Experiment 2 ....................................................................................................... 55
Experiment 3 (Exposed Site)...............................................................................56
Growth, Condition and Fin Damage.................................................................. 57
Surface Rolling and Jumping Behavior.............................................................58
Statistical Analysis.............................................................................................. 58
Results.......................................................................................................................58
Experiment 1........................................................................................................58
Experiment 2 ........................................................................................................60
Experiment 3 ....................................................................................................... 62
Discussion.................................................................................................................63
IX
IV. TECHNOLOGY TRANSFER OF SMALL SCALE INTEGRATED MULITROPHIC
AQUACULTURE TO COMMERICAL FISHERMEN IN N H .......................................79
Abstract.....................................................................................................................79
Introduction...............................................................................................................80
Materials and Methods............................................................................................ 83
Permitting.............................................................................................................83
Integrated Multi-trophic Aquaculture................................................................ 85
Culture Technology........................................................................................85
Steelhead Trout............................................................................................... 86
Blue Mussels................................................................................................... 86
Sugar Kelp.......................................................................................................87
Technology Transfer to NH Fishermen.............................................................87
Environmental Monitoring..................................................................................88
Market Survey of Steelhead Trout..................................................................... 89
Results....................................................................................................................... 90
Demonstration of Integrated Multi-trophic Aquaculture..................................90
Steelhead Trout............................................................................................... 90
Blue Mussels................................................................................................... 91
Sugar Kelp.......................................................................................................92
Fate of Nitrogen ................................................................................................. 94
Technology Transfer to NH Fishermen.............................................................95
Environmental Monitoring..................................................................................97
Water Quality.................................................................................................. 97
X
Benthic and Video Sampling..........................................................................97
Market Survey of Steelhead Trout.......................................................................... 98
Steelhead Trout Economics for NH Fishermen..................................................... 98
Discussion............................................................................................................... 100
Dissertation Synopsis..........................................................................................................121
APPENDIX A. ANIMAL CARE AND USE APPRO VEAL 2013................................125
APPENDIX B. ANIMAL CARE AND USE APPROVEAL 2010................................126
APPENDIX C. NH FISH & GAME AQUACULTURE PERMIT 2013........................128
LIST OF REFERENCES....................................................................................................130
XI
LIST OF TABLES
TABLE TITLE PAGE
1.1 Growth performance of cod in nylon and copper cages............................................... 18
2.1 Environmental ranges at the experimental site during the study period......................39
2.2 Mean distances of trout from net tags during four sampling periods.......................... 40
3.1 Mean weights, lengths, condition and nose abrasion from the different treatments
in Experiment 1.............................................................................................................. 66
3.2 Specific growth rates of each of the indicated treatments at the end of
Experiments 1,2 and 3 ..................................................................................................67
3.3 Mean weights, lengths, condition and nose abrasion from Experiment 2 ...................68
3.4 Growth and condition index for Experiment 3 ............................................................. 69
4.1 Consumer survey form for steelhead trout market evaluation......................................103
4.2 Nitrogen inputs and outputs from integrated multi-trophic aquaculture..................... 104
4.3 Water quality data collected during the demonstration project....................................105
4.4 Water sampling for nitrogen content from three locations........................................... 106
4.5 Economic spreadsheet of steelhead trout production at 100 m3...................................107
4.6 Economic spreadsheet of steelhead trout production at 500 m3...................................108
4.7 Economic spreadsheet of steelhead trout production at 1000 m3.................................109
Xll
LIST OF FIGURES
FIGURE TITLE PAGE
1.1 Floating raft with six net pens under the UNH pier...................................................... 19
1.2 Mean weight gain of Atlantic cod cultured in nylon and copper nets.........................20
1.3 Mean total bio-foul weight from each cage at the termination of the experiment ....21
1.4 Chemical analysis conducted on cod muscle, liver and gill from the control and
treatment ........................................................................................................................22
2.1 Google Earth photos of Fort Point, New Castle, NH, USA and the Judd Gregg
Marine Research Pier..................................................................................................... 41
2.2 Experimental cage design showing placement of the 4 HTI hydrophones and 12
net pingers...................................................................................................................... 42
2.3 An HTI model 795Z acoustic transmitter being implanted into the abdominal
cavity of a steelhead trout..............................................................................................43
2.4 An example of current velocities at the test cage site during ebb and flood tides......44
2.5 An illustration of a single fish and group of four fish, tracked on June 17................ 45
2.6 Density plot showing the distribution of a single trout on June 18 from 0800-
0900h..............................................................................................................................46
2.7 Relationship between swimming speed and current speed recorded by a Modular
Acoustic Velocity Sensor current meter.......................................................................47
2.8 Mean swimming speeds of the seven fish during day and night intervals.................. 48
Xlll
3.1 Aerial photo of the Judd Gregg Marine Research Pier in New Castle, NH and
proximity to the experimental sites............................................................................... 70
3.2 Cage design used in Experiment 1..................................................................................71
3.3 Control and treatment cages for Experiment 2.............................................................. 72
3.4 Steelhead trout attached with a fitted Star-Oddi™ pitch and roll data storage tag ...73
3.5 Visual representations of subjective snout index...........................................................74
3.6 Number of fish jumps per cage sampling during Experiments 1, 2 and 3...................75
3.7 An example of pitch recordings, taken from a fish in the submerged and surface
cages...............................................................................................................................76
3.8 Survival of trout in Experiments 1, 2 and 3................................................................... 77
3.9 Bio-fouling of the hydroid Tubularia on a fish net....................................................... 78
4.1 Trout cages moored at the mouth of the Piscataqua River, NH ..................................110
4.2 Natural settlement of sugar kelp on the trout cages in the Piscataqua River, NH....... I l l
4.3 Fishermen harvesting steelhead trout for local markets in Portsmouth, NH............... 112
4.4 Juvenile mussel spat that settled on the New Zealand fuzzy rope suspended
around the cage platform................................................................................................ 113
4.5 Mussels being set into modified lobster pots for relaying offshore near Gunboat
Shoals, NH...................................................................................................................... 114
4.6 Juvenile sugar kelp lines being deployed for growout on a floating platform ...........115
4.7 Sugar kelp after 4 months growout in the Piscataqua River, N H .................................116
4.8 The fate of nitrogen from fish food to the environment............................................... 117
4.9 NH fishermen towing empty cages to site for growout of steelhead trout, mussels
and sugar kelp in the Piscataqua River, N H .................................................................118
XIV
4.10 Harvest of steelhead trout from the sea cages with the Portsmouth fishermen...........119
4.11 Diver with a Go Pro™ underwater camera filming a 30 m bottom transect under
the sea cages in the Piscataqua River, NH....................................................................120
XV
ABSTRACT
RESEARCH AND DEVELOPMENT OF STEELHEAD TROUT Oncorhynchus mykiss
AQUACULTURE IN SEA CAGES
by
Michael David Chambers
University of New Hampshire, December, 2013
The overall research goal was to develop technological, behavioral and
operational information that could enhance marine aquaculture in New England. Our first
study field tested a copper alloy cage material (Seawire) to reduce bio-fouling, a major
impediment to cage farming. We found that the Seawire significantly reduced bio-
fouling. In the second study we investigated a bio-telemetry system (Hydroacoustic
Technologies Incorporated) to monitor steelhead trout (Oncorhynchus mykiss) movement
inside a net pen as the net was deformed by strong tidal currents (~ 0.50 m / sec.). Results
showed that the net became deformed at currents > 0.2 m / s, and at current speeds of 0.5
m / s, the net lost > 30% of its volume. Trout swimming behavior was influenced by tidal
velocity. As velocity increased, trout exhibited rheotaxis, and used less of the cage
volume. No significant day/night differences were found in swimming depth or speed.
The third study explored the possibility that steelhead trout, a physostomous species,
could be held in submerged net pens for prolonged periods of time. Treatments were
sampled for growth, SGR, K, survival, skin and nose abrasions, and jumping behavior.
XVI
Results indicated that trout could be submerged for days to weeks with no negative
effects.
Finally, NH commercial fishermen were successfully trained on small-scale,
integrated multi-trophic aquaculture (IMTA) of steelhead trout, blue mussels (Mytilus
edulis) and sugar kelp (Saccharina latissima). The IMTA results demonstrated that
nutrient extraction by the mussel and kelp exceeded the nutrient input from trout
production. A simple economic analysis of small-scale trout aquaculture indicated a
profit could be made, which could supplement the income of commercial fishermen.
Lastly, market surveys and sales of steelhead trout suggested consumer demand for a
locally raised product. Taste, texture, smell, and color all rated excellent in the survey
forms.
XVII
INTRODUCTION
The global demand for seafood continues to rise while many wild fish and
shellfish stocks are at or beyond sustainable harvest levels (FAO, 2012). Fisheries catches
have been declining over the past two decades (Pauly et al., 2003), and many stocks are
currently overexploited (Myers and Worm, 2003, Naylor and Burke, 2005). Since the
mid-1990s, aquaculture has been primarily responsible for the growth in global fish
production as capture production has leveled off. Its contribution to total world fish
supply climbed steadily from 20.9 percent in 1995 to 40.3 percent in 2010 (FAO 2012).
In 2010, world marine farming production was estimated at 36.1 million tons with
a value of US$37.9 billion (FAO Statistics and Information Branch of the Fisheries and
Aquaculture Department, 2012). Nearly all ocean farming is conducted inshore, in
contrast to offshore aquaculture that is still in its infancy. Offshore aquaculture may be
defined as taking place in areas of the open ocean exposed to significant wind and wave
action, and where there is a requirement for equipment and servicing vessels to survive
and operate in severe sea conditions from time to time (Drumm, 2010).
Drivers at local and global levels provide impetus for aquaculture to move to the
unprotected waters of the open sea. There are issues of competition for space with other
users, problems with water quality, and oftentimes there is a negative public perception
of aquaculture’s environmental and aesthetic impacts (Kapetsky et al., 2013).
The U.S. is the third largest consumer of seafood in the world behind China and
Japan (FAO 2012). At present, the U.S. imports 85% of its seafood, half of which is
1
aquaculture products. Seafood produced overseas does not always adhere to strict
oversight on farm practices or environmental standards. As U.S. consumers demand safe
and sustainable seafood, the U.S. needs to develop responsible measures to produce
environmentally safe and sustainable aquaculture practices.
The US government invested in ocean aquaculture in 2005 with the development
of the National Offshore Aquaculture (http://aquaculture.noaa.gov/us/2007.html). It cites
the increasing global demand for seafood, notes that the U.S. seafood trade deficit is >
$10 billion, emphasizes the need for a safe and reliable seafood supply, and recommends
that the U.S. aquaculture industry grows at the rate of 4-6 million metric tons per year.
There is an obvious need for aquaculture development in the US. However, one of
the most difficult obstacles to overcome is finding locations for new aquaculture farms.
Because of the difficulties associated with inshore locations, it is assumed that most new
aquaculture activities will be developed offshore in the Exclusive Economic Zone (3-200
miles) where there are fewer conflicts with existing user groups, and less risk of
pollution. The high energy (winds and waves) of such exposed locations, however,
present significant technical challenges in the design, testing and construction of
aquaculture systems that are capable of surviving in these areas. In addition to these
technical challenges, there are many biological, regulatory, social and economic
problems to be solved.
The University of New Hampshire (UNH) established the Open Ocean
Aquaculture (OOA) research farm in 1999 (http://ooa.unh.edu/). The overall goal of the
project was to stimulate the further development of commercial offshore aquaculture in
New England. Also important was to work closely with commercial fishermen, coastal
2
communities, private industry, and fellow marine research scientists to develop
technologies for the aquaculture of native, cold-water finfish and shellfish species in
exposed oceanic environments. The site was located 12 km offshore and in 50 m water
depth, away from traditional fishing activities, recreational vessels and commercial
traffic. The project was successful in demonstrating and developing new submersible
cage (Chambers et al., 2011), mooring (DeCew et al., 2012), mussel longline
technologies (Langan et al., 2003) and remote feeding systems (Rice et al., 2003). In
addition, it successfully produced several cold tolerant marine fish species (Howell et al.,
2005; Chambers et al, 2006,2007; Rillahan et al., 2009, 2011), and collected and
transmitted environmental data from the remote location to shore, in real time (Irish et al.,
2004, 2011). Although the project succeeded in generating significant amounts of data
and new information, the high maintenance costs, exposed nature of the site, and slow
growth of the marine fish species created operational and economic challenges.
To overcome the challenges stated above, research at UNH helped develop a new
aquaculture model that could be adopted by fishermen. This model was smaller scale,
more affordable and pertinent to their existing infrastructure. Over the last five years, the
New England commercial fishing fleet has been faced with repeated management
measures established to rebuild declining stocks. By design, these measures have limited
fishing opportunities and significantly reduced the inshore small vessel fleet. More
recently, on May 1, 2010, a new management framework was established which changed
the regulation of fishing effort from a Days-at-Sea strategy to catch shares or a quota
system. The allocation groundfish fishermen received was conservative, and will result
in up to a 40% decrease in potential landings. This loss has been forecasted to reduce the
3
current groundfish fishing fleet by an additional 50% (NH Sea Grant, 2013). For many
local communities this will mean the loss of a historic fishing heritage. We see
aquaculture as an appropriate business alternative for the small vessel owner, to either
transition from wild harvest fisheries to farming, or to subsidize loss of income resulting
from limitations placed on individual landings.
Steelhead trout (Oncorhynchus mykiss) was considered for the new farming
model because of its unique characteristics for aquaculture. First, it has been
domesticated for >150 years, and is the basis for extensive commercial aquaculture
industries in Canada and Northern Europe. Second, unlike Atlantic salmon, the species
does not go through true smoltification, so juveniles > 100 g can go directly from a
freshwater hatchery to full strength seawater. Third, the species has a relatively fast
growth rate, reaching marketable size (1-3 kg) only 6-9 months after stocking at 100-
150g (www.dfo-mpo.gc.ca/Aquaculture/finfish/steelhead_e.htm). Finally, they are
disease resistant, are more temperature tolerant than Atlantic salmon, and have a high
market value.
Despite all the positive attributes for steelhead trout, a number of questions
remained concerning the usefulness for cage aquaculture in near shore New England
waters. First, was concern of their ability to survive in net environments located in high
current areas (> 0.35 m / sec), second, because of the nature of their swim bladder
(physostomous), it is not clear if they could tolerate prolonged periods of time away from
the surface, when cages need to submerged to avoid surface storm activity. Finally, it is
not clear if they could be grown economically and sold locally at a fair price. The overall
goal of my thesis research was to address these issues and determine if, in fact, it is
4
feasible to raise steelhead trout on a small scale in NH waters. To address these concerns,
studies were designed and conducted between 2009 -2013 to examine biological and
technical methods to sustainably culture steelhead trout. Chapter one investigates a new
material (Seawire) that reduces bio-fouling on sea cage systems. This is a major
impediment to cage culture, especially during the warmer summer months. Chapter two
examines the reaction of trout to net deformation caused by strong tidal currents. The
distorted environment and crowding can cause stress to fish in culture. Chapter three
considers moving trout culture offshore to exposed locations. Here, potential waves,
currents and temperature extremes can make surface culture difficult. Submerging fish
can alleviate these problems though trout need to gulp air to maintain the swim bladder
for buoyancy. Finally, in chapter four, lessons learned from the OOA project and chapters
1-3 were applied to help train local fishermen on aquaculture as a means of
supplementing their income while fishing. This applied component was critical in
transferring technology to a user group that could adopt culture methods that were
applicable with their existing infrastructure. We continue to work with NH fishers to
build a successful aquaculture industry.
5
CHAPTER I
EFFECTS OF BIOFOULING ON COMPARATIVE GROWTH AND SURVIVAL OF
JUVENIL ATLANTIC COD (Gadus morhua) CULTUREED IN OCEAN PENS
Abstract
Bio-fouling on net pens has been a major concern for the marine aquaculture
industry. As cage systems increase in size, so does the surface area for the attachment of
colonial organisms creating drag on the net, reduced water flow important to fish health,
and increased operational expenses due to net cleaning. To solve this problem, the
International Copper Association (ICA) has been developing copper alloy netting for sea
cages. Copper netting has unique properties that minimize bio-fouling, reduce the risk of
fish escapement, prevent predators from entering the net pen, and is recyclable. To test
the alloy netting, an experiment was designed to compare juvenile cod cultured in
traditional nylon nets with Cu netting produced by Luvata ([email protected]). Six
0.78 m3 cages were stocked with 200, 29 g Atlantic cod (Gadus morhua) and grown for 4
months in coastal waters of New Hampshire, USA. Results of the study indicated no
significant differences in cod growth, survival, FCR, SGR, and CF between the two
treatments. A proximate analysis also indicated no differences in Cu levels in cod muscle,
liver and gill tissues taken from the control fish and fish raised in the Cu cage. Nylon nets
with antifouling paint accumulated significantly more bio-fouling then the Cu nets and
materials that were in contact with the Cu netting (plastic cable ties) fouled heavily with
6
hydroids indicating minimal leaching to the environment. This study describes some of
the beneficial attributes of Cu netting, however future studies need to be conducted over a
longer period of time, on a larger scale, and in a more energetic environment to
definitively test the utility of this new product.
Introduction
The marine aquaculture industry is moving towards more environmentally
sustainable practices. A common issue with cage farming is the attachment of biological
communities to the culture net creating reduced water flow, decreased water quality and
excessive weight and drag on the cage floats (Fredriksson et al., 2003; Braithwaite and
McEvoy, 2005; Swift et al., 2006; Lader et al., 2008; de Nys and Guenther, 2009).
Aquaculture nets are prone to settlement and successional development of hydroids
(Green and Grizzle 2007) that significantly increase operational costs of farming due to
net cleaning (Hodson, et al., 1991; Braithwaite et al., 2007 and Solberg et al., 2002). To
combat this problem, the industry impregnates their nets with antifouling paints with
active ingredients such as cuprous oxide, cadmium and zinc (Hodson, et al., 1991;
Braithwaite et al., 2007 and Solberg et al., 2002; Dean et al., 2007; Brooks, 2003;
Brooks, 2000 and Voulvoulis et al., 1999. The active ingredients eventually leach out
over time (10-12 months) and thus fouling organism adheres to the net surface
(Braithwaite et al., 2007).
A new approach to circumvent this problem has been the development of new
containment materials that are stronger, resistant to bio-fouling and friendly to the
environment. The International Copper Association (ICA) has been investigating copper
alloy netting for fish farming (Chambers et al., 2011). Copper netting exhibits both
7
antifouling and anticorrosion properties. When copper netting is introduced into seawater,
an adherent protective patina layer is formed, that inhibits corrosion and resists the
attachment of fouling organisms. A clean net maintains water movement through the
cage for optimal fish health. Moreover, net cleaning is expensive, time consuming and
stressful to the fish. The strength of copper netting helps prevent escapement and deters
predators such as seals and sharks. Lastly, at the end of the copper netting shelf life, it can
be sold back to the manufacturer and recycled into another copper net or product.
Copper is naturally occurring in water, sediments and organisms, and is an
essential micronutrient for normal growth in plants and animals (Chester, 1990). As such,
fish diets for aquaculture maintain copper levels ranging from 5-14.8 mg / kg (Lie et al,
1989). Copper is also used as a biocide to treat fish disease including ectocommensal
ciliates (Noga, 2000), Amyloodinium (Van Duijn, 1973), Cryptocaryon (Tookwinas,
1990) and Monogenes (Thoney, 1990). Despite these positive attributes, it should be
noted that fish are much more sensitive to aqueous metals than humans, and too much
copper can cause metal poisoning. Copper toxicosis affects the gills, resulting in
osmoregulatory dysfunction, and can affect the kidney and liver (Cardeilhac & Whitaker,
1988). Therefore, oxidation levels from copper netting must be minimal for fish to
remain healthy.
Atlantic cod is one of the most valuable and commonly consumed species in the
western world, and declines of wild populations have brought a renewed interest in cod
aquaculture. In New England, research efforts have been underway at the University of
Hampshire’s (UNH), Open Ocean Aquaculture (OOA) site (http://ooa.unh.edu/) to
develop grow out technologies for this species (Chambers et al., 2006, 2007; Rillahan et
8
al., 2009, 2011). Recent developments in cod larval production in the US, Norway,
Canada and the UK have created a consistent supply of fingerlings for grow out in cages.
Despite successes in hatchery production, culture issues remain with ocean nursery and
grow out systems. One behavioral issue with cod is their tendency to bite at the net twine
creating holes through which the fish can escape (Moe et al. 2006). This has been a
problem in Norway that has slowed the expansion of the industry. It is clear that
alternative containment materials that reduce bio-fouling and escapement would be
beneficial to the industry.
The goal of this research was to compare the growth, survival and behavior of
juvenile Atlantic cod cultured in copper alloy and traditional, industry standard nylon net
pens with antifouling paint. It also compared fouling rates on the two net types, and
examined Cu levels that may have been absorbed into the fish from the copper netting.
The four month experiment was conducted at the UNH Marine Pier Facility in New
Castle, NH, USA during the spring and summer of 2010.
Methods and Materials
Cage design
A total of six floating cages were constructed, each with a volume of 0.78 m3.
These were attached to a wooden raft located near the UNH pier in Newcastle, NH, USA
(Fig. 1). Each cage frame was made from 2.5 cm diameter high density polyethylene pipe
(HDPE). Netting materials were stretched and cable tied to each frame. The three nylon
cages (control) were made from 1.25 cm x 1.25 cm mesh nylon coated with Flexgard™, a
cuprous oxide based antifouling paint (http://www.trademarkia.com/company-flexabar-
9
corporation-451575-page-1-2, New Jersey, USA). Flexgard is the industry standard
antifoul paint used for salmon aquaculture in the eastern US and Canada. The three
copper cages (treatment) utilized Seawire™, a copper silicone material produced by
Luvata ([email protected]. Appleton, WI USA). At the time of the experiment,
Luvata only produced a 2.5 cm x 2.5 cm mesh net. To match the copper net to the nylon
mesh size of 1.25 cm (the size necessary to maintain small cod in the cage), two pieces of
Seawire net were laid on top of each other and spaced to form a 1.25 cm x 1.25 cm mesh.
Cable ties and copper hog rings were used to secure the Seawire in place and keep it from
shifting into a larger mesh size.
Stocking and feed
Each cage was stocked at a density of 7.4 kg / m3 with 200, 29 ± 2.2 g cod
produced by Great Bay Aquaculture located in Newington, NH USA. Initially, the cod
were fed twice daily with a vibratory feeder at 1.5% body weight / day with a 3 mm,
Skretting™ Europa diet composed of 50% protein and 18% lipid (Portland, ME USA).
Later in the experiment, cod were hand fed to satiation, once daily.
Behavioral and environmental monitoring
Each cage was monitored with a Super Circuits ultra-high resolution camera
(Model # PC88WR-2, Austin, TX USA) and video was recorded on a Super Circuits 8
channel DVR (Model # DH200800D, Super Circuits, Austin, TX USA). Feeding,
swimming behavior and interactions with the nets were recorded on the DVR. Water
temperature, dissolved oxygen, salinity, pH, turbidity and tidal height were recorded
every 30 minutes with an YSI 6600 Multi-parameter Sonde (YSI, Yellow Springs, Ohio
USA). Light levels were monitored from the bottom of the cages with a HOBO Pendant
10
Temperature and Light Data Logger ( Onset Computer Corp, Cape Cod, MA USA), and
current speed and direction were measured periodically with a portable Marsh McBimey,
model 2000, flow meter (Hach Company, Berlin, MA USA).
Data collection
Random samples of 30 cod were collected monthly from each cage to measure
wet weight and total length. Fish were starved for 24 hours prior to sampling. At the
termination of the study, FCRs, based on 50 fish from each of the control and copper
nets, were calculated as [total feed weight fed * % dry matter] / [(mean harvest weight-
initial mean weight) * number of fish].
Standard indices of growth and condition of fish were calculated for each cage.
SGR (% day .) was calculated as [(In (W2) - In (W.)] / (t2 - t.) where W2and W. are the
mean live body weights at times t2 and t., respectively. Fulton’s condition factor was
calculated with the formula K = (W / L.) x 100, where W is the wet weight (g), and L is
the total length (cm).
Chemical analyses of 3 replicate tissue samples of gill, liver and muscle, each
weighing 5-10g and taken from 10 randomly selected fish from the copper alloy and
nylon nets, were run at the end of the experiment. Tissue samples were frozen in zip lock
bags and shipped to New Jersey Feed Labs in Trenton, NJ, USA. There, samples were
placed into a crucible and heated to 600°C for 2 hrs. The dry ash sample was then diluted
with hydrochloric acid and placed into an IC-AES (Inductively Coupled Plasma Atomic
Emission Spectrometry) to measure copper content (AOAC # 985.01)
Finally, each cage with fouling community was removed from the water and
weighed on an Ohaus ES series bench scale (Parsippany, NJ USA) for total weight.
11
Fouling organisms were identified and photographed. Each cage was then pressure
sprayed clean and re-weighed to obtain weight differences between fouled and clean
cages.
Unpaired t-tests were used to compare survival, FCR, SGR, K, copper uptake and
bio-fouling results between the control and treatment nets.
Results
Environmental
Environmental data collected during the study showed: a) current was
omnidirectional, and varied from 0.2 - 0.4 cm / sec; b) water temperature ranged from
6.4°C in April to 19.2°C in August; c) light levels in the bottom of net cages (-1.5 m)
ranged from 0-2 lumens / ft2; d) salinity ranged from 21.5 - 34.3 ppt.; and e) dissolved
oxygen ranged from 11.3 mg /1 in April to 6.3 mg /1 in August.
Cod performance
Fish increased in weight by 80.8 ± 2.2 g in the nylon cage and 84.9 ± 9.4 g in the
Cu cage during the 16 week trial (Figure 2 and Table 1). Mean weights from replicates in
each treatment were not significantly different (Kruskal-Wallis tests, P > 0.05) so all
replicate weights within treatment were combined. There was no significant difference in
mean weight (Unpaired t-test with Welch correction, P > 0.05) between fish raised in the
copper alloy and Flexgard treated nylon cages. Also not significantly different (Unpaired
t-tests, P > 0.05) were cod lengths, survival, FCR, SGR and K (Table 1).
In mid-May, three consecutive storms and runoff increased water turbidity in the
Piscataqua River. Shortly after this event, mortality was observed in all of the cages. Cod
12
postmortem samples (6 / cage) were submitted for necropsy at the UNH Veterinary
Diagnostic Laboratory in Durham, NH. The cod were diagnosed with Aeromonas
salmoncida septicemia, with focally marked fibrinonecrotizing dermatitis of the dorsal
fin. Consequently, slow chronic mortality was observed during the rest of the experiment
despite increased growth rates in all the cages.
Bio-fouling
As temperatures increased through the summer (up to 19°C), so did the amount of
bio-fouling on the HDPE frames and nylon nets. Organisms found on the two cage
treatments included the hydroid Tubularia crocea, the red gilled nudibranch (Coryphella
sp.), skeleton shrimp (Caprella sp.) and the tunicate Ciona intestinalis. Tubularia was the
dominant fouling species that reduced water flow through the cages. Bio-fouling rates
between the treated nylon net and copper netting were significantly different (T-test,
P<0.05). The mean (± SE) fouling weight (fouling community alone) of the nylon nets
was 22.8 ± 2.67 kg compared to a mean weight of 16.2 ± 2.95 kg for the copper net pens
(Figure 3). Fouling on the Cu cages only occurred on non-alloy materials (HDPE frame
and plastic cable ties). The 2 x 3 mm cable ties wrapped around the Cu twine had clumps
of Tubularia ranging from 125-180g. No fouling organisms were observed on the
Seawire netting.
Copper content analysis
Unpaired t-tests, with Welch corrections, were used to compare fish from copper
alloy cages (treatment) and the fish from the nylon Flexgard cages (control). There was
no significant difference (P > 0.05) in ppm copper between fish from the 2 cage types in
bodies (muscle) (P = 0.68), gills (P = 0.47) or livers (P = 0.52) (Fig. 4).
13
Discussion
Nylon nets covered with antifouling paint (Flexgard™) are commonly used to
prevent antifouling on aquaculture nets in North America. The disadvantages of these
nylon nets include wear, vulnerability to predators, susceptibility to cultured species with
biting behavior (e.g. cod), and bio-fouling once the antifouling coating is lost. Copper
alloy netting provides a new containment material that may resolve some of these issues.
Its strength, corrosion resistance, and antifouling properties provide longer wear, help to
maintain water flow, prevent escapement and exclude predators. Furthermore, because of
the reduced fouling communities and increased water flow, smaller mesh copper nets
could be used to hold juvenile fish. This would allow fingerling fish to be moved to net
pens at smaller sizes, thus reducing operating expenses associated with land based
hatcheries.
We found no significant differences in the growth, survival, FCR, SGR, and K
between cod cultured in the nylon nets with Flexgard antifoul paint and cod raised in the
copper nets. Despite the mortality caused by the bacteria infection Aeromonas
salmoncida, the survival of the fish in the control and treatment was similar. Moreover,
there were no difference in copper uptake in gill, liver and muscle tissue samples taken
from fish held in nylon cages with Flexgard™ antifoul paint (cuprous oxide based) and
the copper Seawire cages. Therefore, even though copper can be detrimental to fish, these
data indicate that the copper cages used for this experiment had no obvious negative
impact on fish growth or survival. Other findings were that nylon nets with antifouling
paint accumulated significantly more fouling biomass than the copper alloy nets, and that
the most abundant fouling organism, found on all cage frames, and on the twine of the
14
nylon nets, was the hydroid Tubularia crocea. Hydroids are common, and quickly settle
onto substrates before other species establish themselves (Harris, 1886; Harris & Irons,
1882 and Lovely, 1995). This species grew throughout the experiment, but remained
absent on all of the Seawire net material. The patina layer that forms on the Seawire net
helps prevent hydroid stolons from attaching. Hydroids use different attachments
methods on nylon nets that include growth between and around individual netting fibers
(de Nys and Guenther, 2009).
Cable ties that were used to secure the two layers of copper netting together did
foul with Tubularia. Hydroid colonies up to 180 g in weight were found on 2 x 3 mm
plastic ties that were in direct contact with the Seawire net. The significant fouling
growth on the cable tie, in direct contact with the Seawire, suggests localized copper
release. It also indicates that all fasteners used in copper alloy cage construction should
be made of similar copper fasteners to eliminate fouling.
Although this study found no adverse effects of copper alloy netting on cod,
future investigations should include longer term, commercial scale trials of copper alloy
netting. Inquiries should be conducted with marine fish species in cold, temperate and
tropical environments with different fouling communities. Other areas to research include
copper leaching into the environment over time and its effect on benthic communities
near the fish farm. Results of such studies will help determine copper netting shelf life,
corrosion strength, benefits to aquaculture and effects on the marine environment. The
data will also serve to guide the design and manufacture of future alloy nets for
aquaculture.
15
Conclusion
Bio-fouling is a major concern with cage farming throughout the world. At
present, the salmon farming industry uses nylon nets treated with an antifoul paint to
reduce bio-fouling. Seawire represents a new material that could deter bio-fouling while
minimizing escapement and preventing most predators from entering the cage
environment. Unlike nylon nets that are disposed of when worn out, Seawire maintains
its value and can be recycled. The cost of 2 cm mesh nylon net, treated with Flexgard is
$16.87 / m2 compared to Seawire with 2.4 cm mesh is $39.69 / m2. Despite the initial cost
difference, Seawire may be as cost effective as nylon by decreasing operational costs
associated with net cleaning, repair and rotation.
Seawire netting comes in roles 1.25 m x 31.25 m. Cages can be easily
manufactured to different dimensions with a pneumatic cutter and stapler. Seawire is a
welded copper mesh that maintains a rigid geometry even during high current episodes
when nylon nets can compress and loose volume. The rigidity may cause challenges in
the fabrication and deployment of commercial size cages. These operational methods and
expenses will need to be calculated to fully understand the cost benefits of using the wire
in an ocean environment.
Copper alloy netting has been investigated in larger scale systems in Tasmania,
Japan and more recently in Chile and Turkey. These cages used a UR30 woven copper
mesh of 40 mm for final grow out of larger fish. The woven net is collapsible on land and
is flexible in the water (http://www.ecosea.cl/). The mesh size is only available in large
sizes and not suitable for studies with juvenile fish. The cages used in the New
16
Hampshire field trial were small (0.78 m3) and in close proximity for replicate purposes
and may not illustrate commercial significance. Setting of the experiment under a pier
and with a new aquaculture species (cod) may not have been the best scenario for this
study. Bacterial infection played a major part in the survival of the cod juveniles despite
their continued growth. Future studies are warranted to reveal benefits and drawbacks of
copper netting in aquaculture.
17
Table 1.1. Growth performance of cod in nylon and copper cages. Means are ± SE. Unpaired T-tests showed no significant differences (P > 0.05) in any of the measured variables between cage types.______________________________________________
Nvlon cage Copper cageInitial weight (g) 29.2 ± 6.7 29.2 ± 6.7Final weight (g) 110.0 ± 1.25 114.1 ±2.28Weight gain (g) 80.8 ± 0.3 84.9 ± 1.3Initial length (cm) 15.4 ± 1.0 15.4 ± 1.0Final length (cm) 22.2 ±0.01 22.3 ±0.11Length gain (cm) 6.8 ± 0.02 6.9 ± 0.05Survival (%) 29.17 ± 1.20 27.67 ±2.41FCR 1.52 ±0.45 1.51 ±0.13SGR (%/day) 0.72 ± 0.07 0.75 ± 0.07Condition factor (K) 1.0 1.0
18
(A) (B)
Figure 1.1. Floating raft with six net pens under the UNH pier (A). Copper net pen stocked with 200, 29 g cod with auto feeder (B).
19
140
100
80
Nylon net
Copper net
April'10 May '10 June’10 July'10 Aug *10
Figure 1.2. Mean weight gain (±SE) of Atlantic cod cultured in nylon and copper nets. Mean weights from replicates in each treatment were not significantly different (Kruskal- Wallis tests, P>0.05) so all replicate weights within treatment were combined. There was no significant difference in mean weight (Unpaired t-test with Welch correction, P>0.05) between fish raised in the copper alloy and Flexgard™ treated nylon cages.
20
Figure 1.3. Mean total bio-foul weight (± SE) from each cage at the termination of the experiment. Bio-foul weight on the copper pens was significantly less (16.2 ± 1.70 kg) than the bio-foul weight on the nylon pens (22.8 ± 1.54 kg) (Unpaired T-test, P < 0.05).
21
M uscle Liver
Tissue
Figure 1.4. Chemical analysis conducted on cod muscle, liver and gill from the control, (nylon nets with Flexgard™ paint) and the treatment (copper Seawire pens). Unpaired t- tests, with Welch corrections, were used to compare the two, and there was no significant difference (P > 0.05) in ppm copper between fish from the 2 cage types in muscle (P = 0.68), gills (P = 0.47) or livers (P = 0.52).
22
CHAPTER n
FIELD MEASUREMENTS OF STEELHEAD TROUT Oncorhynchus mykiss
DISTRIBUTION, SWIMMING BEHAVIOR AND RESPONSE TO WATER
CURRENT EXPOSURE IN A SEA CAGE
Abstract
This study introduces a new way to measure the distribution and behavior of
steelhead trout in a sea cage in response to fluctuating tidal currents that deform the net.
Strong currents can significantly decrease the volume of net constraining fish to a
condensed area. An ultrasonic telemetry system (Hydroacoustic Technology Inc., model
291) was deployed around a 63 m3 sea cage stocked with 200 steelhead trout
(Oncorhynchus mykiss). Fish and cage movement were monitored using ultrasonic tags
implanted into the abdominal cavities of 8 sentinel trout, 12 more were attached around
the net bottom and midsection. The signals were detected by four omni-directional
hydrophones that were connected to a receiver on a nearby pier. Signals detected at 2
second intervals were used to plot 3 dimensional locations of both the fish and net. We
found that current flow inside the net was significantly reduced (32-53%) compared to
outside and that swimming behavior was influenced by tidal currents. As current speed
increased, the positions of fish became more restricted because they were swimming into
the current to maintain their position. In contrast, during slack tides, fish exhibited typical
23
schooling behavior and swam in a circular pattern. This study demonstrates the use of
acoustic telemetry on a small scale cage. This technology can be applied to a commercial
scale farm to improve fish welfare and cage design.
Introduction
Since the mid-1990s, aquaculture has been primarily responsible for the growth in
global fish production as capture production has leveled off. Its contribution to total
world fish supply climbed steadily from 20.9 percent in 1995 to 40.3 percent in 2010
(FAO 2012). Most marine aquaculture takes place in near shore waters that provide
protection from storms and easy access to the farms. However, these waters are prone to
user conflicts from traditional fishermen, commercial traffic, and recreational boaters.
Resistance also comes from seashore abutters who worry about their view-scape. Finally,
runoff from land can create unfavorable conditions for raising healthy fish. Moving
aquaculture production offshore into deeper, more energetic, waters alleviates some of
the above issues. However, moving into more exposed areas increases risk and operating
expenses, decreases days at sea to tend the farm, and creates technical challenges with
infrastructure.
Understanding high energy environments is essential to the biological
requirements of a marine fish. In ocean cage culture, fish are often exposed to more
intense physical and environmental perturbations (Oppedal, et el. 2010), which can lead
to increases in metabolism and thus reduced growth and even mortality. Stress responses
in farmed fish have been shown to result from environmental disturbances, farming
operations or high stocking densities (Begout & Lagardere 1993; Cooke et al., 2000;
24
Begout & Lagardere, 2004; Chandroo et al., 2005). Measuring and understanding these
stressors can help farmers improve their operations, increase production efficiency and
optimize fish welfare. When changes occur in a cage environment, natural defense
mechanisms, such as net avoidance behavior, take effect. These behaviors have evolved
to lessen the probability of death, to mitigate the higher metabolic costs incurred by
increased swimming, and / or to maintain physiological homeostasis (Olla et al. 1980,
Schreck et at. 1997).
Fish distribution within a net pen is affected by an array of parameters such as
temperature, feeding and light (Oppedal et al., 2001; Oppedal et al., 2007; Oppedal et al.,
2010). Distribution can also be effected indirectly by bio-fouling, since bio-fouling
increases net resistance to currents, which results in cage deformation and changes in
geometry (Lader et al., 2008; Braithwaithe et al, 2007; Swift et al., 2006; DeCew et al.,
2013; Ward et al., 2012). As cage culture moves further offshore into deeper waters,
larger nets can be used allowing fish to distribute into preferred areas within the cage
environment, e.g. above or below thermoclines, zones of higher oxygen, preferred light
levels and escapement from storm surge. Recent technological advances have made it
possible to investigate how individual fish, as well as groups of fish, respond to the
aforementioned parameters. For example, Rillahan et al. (2009, 2011) studied the
behavior of Atlantic cod in an offshore (12 km) submerged, bi-conical cage (Sea
Station™). They found that cod exhibited clear diurnal rhythms, with the highest
swimming activity during daytime hours. Analysis of cage utilization revealed that cod
did not use the entire cage volume, and that individual space use was limited to small
overlapping areas within the bottom half of the net. When the density of cod reached high
25
levels, as they grew, their typical diurnal pattern of independent swimming changed to
schooling behavior with no significant difference in day and night activity. Ward et al.
(2012) studied cod behavior in near shore, rectangular floating cages at stocking densities
ranging from 5-45 kg / m3). He found that at the lowest density the cod spent the majority
(~ 64%) of their time in the bottom third of the net pen. Then, as density increased, the
fish moved higher in the water column, and this behavior was most evident at night, at all
densities. At no time during the study were there any obvious occurrences of schooling
behavior, even at the highest density. Both of these studies illustrated the usefulness of
high resolution biotelemetry for continuously monitoring the behavior of cultured fish
under a variety of circumstances, and demonstrating how fish interact with each other and
the cage.
While investigations over the past 20 years have revealed a great deal about how
fish behave in net pens in calm to moderate conditions, little is known about how both the
nets, and the fish inside the nets, respond during the intermittent storm events that are
fairly typical for exposed offshore cages. During these storms the waves and currents
increase and net deformation is likely, which may, or may not, lead to alterations in the
normal behavior of the fish. One of the goals of this study was to determine if acoustic
telemetry could be used, as a tool, to monitor both the deformation of the net, and the
movements of the fish, in a net pen exposed to stronger than normal currents. We used a
63 m3 net pen moored at the mouth of a large estuary where tidal current were strong
enough to deform the net pen.
The test species was the steelhead trout (Oncorhynchus mykiss), that is
commercially grown in near shore, protected waters in Chile, Norway, Faroe Islands,
26
Canada, and to a limited extent in the USA (states of Washington and New Hampshire).
Despite its advantages as a species for aquaculture, very little is known about its behavior
in an aquaculture setting. Therefore, by using steelhead trout, we were able to gain
valuable information about this species, as well as data relevant to the response of fish to
strong currents and the resulting deformation of the net pen in which they resided.
Methods and Materials
A 63 m3 net pen was stocked with 200 steelhead trout (Oncorhynchus mykiss),
(Mean (± SD) fish weight 571.7 ± 170.8 g, length 35.6 ± 2.8 cm). Initial stocking density
was 1.8 kg / m3. A Hydroacoustic Technology Inc. acoustic telemetry system (HTI -
http://www.htisonar.com/), similar to the one used by Rillahan et al. (2009, 2011) and
Ward et al. (2012) to study cod behavior, was used to track fish behavior and net
deformation. Eight model 795Z transmitters were surgically implanted into the
abdominal cavity of individual fish to track their temporal and spatial distribution.
Twelve more transmitters were attached around the net (8-middle, 4-bottom) to monitor
the position of the net and deformation caused by tidal currents. Four hydrophones
hardwired to a receiver (Model 291), were used to monitor the positions of transmitters,
in three dimensions, using a suite of HTI programs. Transmitters in the fish and net
“pinged” every 1-3 seconds and theses acoustical signals were detected by each of the
hydrophones. These data were then used to calculate and plot the position of each
transmitter with a resolution of ~ 10 cm, every 2-5 seconds. Stored data were used to
determine the distribution and swimming activity of the fish and movements of the net.
Location
27
The study was conducted at the UNH Judd Gregg Pier Facility on Fort Point, New
Castle, NH, USA at the mouth of the Piscataqua River (Fig. 1). The telemetry receiver,
computer and video monitoring system were located in a small building at the end of the
pier adjacent to the experimental cage. The test cage was moored between two mooring
blocks (4 ton ea.) approximately 30 m from the end of the pier in a water depth of 8 m.
The site experienced 2 ebb and 2 flood cycles per day, with tidal amplitude ranging from
3-3.5 m.
Case design
The sea cage was constructed of two, 15 m circumference (10 cm dia.) high-
density polyethylene (HDPE) pipe that were bent into a ring and fused. One ring was
attached to the top of a 63 m3 cylindrical net measuring 4.6 m in diameter and 4 m in
depth. The second ring (sinker tube) was drilled with 1.25 cm holes and wrapped with a
1.25 cm dia. chain before attaching to the net bottom. The nylon net was made from a 2
mm twine and had a 2.5 x 2.5 cm knotless square mesh that was coated with a cuprous
oxide antifouling paint (Flexguard™). The HDPE rings and net were suspended from a 5
x 5 m floating platform (Fig. 2).
Environmental data collection
An Acoustic Data Current Profiler (ADCP) deployed on the ocean bottom (10 m
from the cage) recorded ambient water velocities and direction at 0.5 s intervals. A
Modular Acoustic Velocity Sensor (MAVS) suspended in the center of the cage 2 m
below surface measured water velocity every 1.0 seconds. Both current meters averaged
and stored data in 5 min bins. Additional environmental data (temperature, dissolved
28
oxygen, salinity, pH, tidal amplitude and turbidity) was collected by an YSI 6600 V2-2
Water Quality Sonde located at the end of the pier adjacent to the cage site (Table 1).
Telemetry set u p
The HTI model 291 telemetry-system (Hydroacoustic Technologies Inc., Seattle,
WA) utilizes four omni-directional hydrophones hardwired to a receiver to monitor the
positions of acoustic transmitters, in three dimensions, using a suite of HTI programs.
The hydrophones were mounted on aluminum posts (5 cm dia.) bolted to the comers of
the float platform, around the net. Two opposing hydrophones were set at a depth of 0.65
m, while the other two opposing hydrophones were at set at a depth of 2.5 m (Fig. 2).
Cabling for the hydrophones was integrated into a mooring line that ran to an
instrumentation shed on the pier. Hydrophones were hard-wired directly to a receiver,
and signals from each tag were transferred to a CPU for storage and analyses. Three-
dimensional positions of sentinel fish and selected points on the net pen were calculated
with a 10 cm resolution, every 2.0 seconds. HTI software was later used to display these
data in near real time (~ 1 minute delay) and also stored as raw data for future analyses.
These stored data points were subsequently processed to eliminate spurious detections
and thus improve the resolution and accuracy of the data. Values were calculated using
the methods previously described by Rillahan et al. (2009, 2011) and Ward et al. (2012).
The data were used to reveal the mean distribution and swimming speed of sentinel fish,
and changes in net geometry. Additional processing was conducted in Matlab and Excel,
data were imported into Tecplot for 3D visualization.
Net Transmitters
29
HTI model 795Z acoustic transmitters were used to monitor the position of the
net. Twelve tags were attached around the net (8-middle, 4-bottom) to monitor the
position of the net and deformation caused by tidal currents (Fig. 2). To isolate individual
transmitters from ambient noise and other transmitters, each was programmed to ping
with a unique inter-pulse interval, ranging from 2,000-3,100 ms. During post-processing,
data from repetitive signals were dissociated from background noise and then assigned to
the individual transmitters, allowing continuous and rapid sampling of multiple
transmitters.
Fish Transmitters
Approximately 200 steelhead trout were transferred from a local hatchery to the
UNH Pier Facility (New Castle, NH) in 1 ton insulated boxes filled with freshwater. The
trout were acclimated from freshwater to seawater (28 ppt.) over a 2 hr. period, and then
netted into the sea cage. Model 795Z transmitters were surgically implanted into the
abdominal cavities of eight individual fish to track their temporal and spatial distribution.
Prior to implanting, each tag was programmed to ping at inter-pulse intervals ranging
between 1100-1800 ms. Trout were anesthetized with tricaine methanesulfonate (MS222)
and the 2.5 x 0.8 cm tags were inserted intraperitonally through a 2 cm incision (Fig. 3) in
the abdominal wall. One suture was used to close the incision, and an external streamer
tag was placed into the dorsal musculature of the fish. The trout were then allowed to
recover for 30 min. before placement in the experimental sea cage. One week later, the
experiment was initiated. During this time, the HTI system was activated and calibrated.
30
To test the possible effect of the surgery and tags on the trout, nine fish were
randomly netted from the cage and transferred to a 2 m diameter x 1 m deep tank in the
UNH Coastal Marine laboratory. Three fish were surgically implanted with a ‘dummy’
tag (same as normal tags, but did not ping), three had surgery but had no ‘dummy’ tag
implanted, and the remaining three fish had no surgery. Fish were observed for tag
retention, initial weight and length verses final, and survival for one month. No difference
was observed between fish with and without tags.
Data processing and statistics
Net transmitters
Net deformation was estimated by determining the differences in net transmitter
(12) locations during slack, intermediate and fast tidal cycles. Changes in net volume
were calculated using scalar triple product, divergence and signed volume methods.
These volumetric calculations are summarized in DeCew et al. 2013.
Fish transmitters
The location of all the pingers was represented by X, Y, Z coordinates that were
calculated with the same frame of reference. Thus, fish could be localized with respect to
each other and with respect to the net. The mean positions of all tagged fish, during each
sampling period were used to calculate mean positions of individuals and groups of fish
during fast and slow current velocities and during night and day within the net pen.
Instantaneous swimming speeds were calculated by taking the square root of the sum of
the three-dimensional (X, Y, Z) distances the fish travelled during a time interval (ti to
t2), and dividing this by the length of the time interval (t2-ti).
31
V (((X2-X,)2) + ((Yr Y.)2) + ((ZrZ,)2)) / (t2-ti)
Mean swimming speeds were calculated during fast and slow current speeds, and
during the night (0200-0300 h) and day (1400-1500 h). Calculations were based on the
positions of the fish relative to the hydrophone array in a steady current, and thus do not
take into account for different ambient current speeds. An unpaired t-test was used to
compare day and night swimming speed (BL / s) of the same seven fish on June 18, 2010.
Linear regression analysis was used to examine the relationship between current speed
within the net pen and swimming speed.
Differences in fish depth were compared across six 1 hour time periods over 24
hours. The positions of fish were averaged individually, and as a group, to obtain a mean
depth estimate per sample period. In order to calculate the amount of the total cage
volume that was occupied by the fish at any given time (cage utilization) we used the
technique developed by Rillahan et al. (2011). First, we created a three dimensional
matrix (10m x 10m x 10m) that encompassed the cage, with grid spacing every 0.2 m in
the X, Y and Z axes dividing the net pen into 0.2 m3 units. Fish positional data was then
overlaid onto the grid and presence/absence was determined for each grid unit. Cage
volume use was then calculated by summing the total grid units utilized by a fish over the
sample period.
A combination of software programs was used to visualize and plot the
movements and positions of fish within the cage. Python Visual Studio 2.0 Alpha was
used to develop wire frame diagrams of the cage during the different tidal and current
episodes. These diagrams were then imported into TecPlot (Version 10) and fish tracks
32
were overlaid in the wire frame to show their movements relative to the modeled cage
environment.
Results
Environmental
Current flow at the study site was bidirectional, with the predominate flow along
the NW-SE vector which coincided with the direction of tidal flow into, and out of, the
river. Current direction was SE (mean 114°) during much of the tidal cycle due to local
bathymetry and eddies. Flow towards the W and NW was relatively slow (0.12 m/s), and
seen only briefly (about 1 hour), about two hours after slack low tide. Currents were
fastest (average 0.24 m/s) on the ebb tides (SE direction). Current speeds outside the net
(ADCP) reached 0.50 m/s during the ebb tide on June 18, 2010. However, current
velocities inside the cage (MAV) were reduced on average by 31% with a high of
approximately 50% (DeCew, et al. 2013). This current reduction was influenced by the
net twine diameter (2 mm) and fouling organisms that accumulated on the net (Fig. 4).
These field results are higher than tank tests (10-20%) conducted by Aames et al. (1990),
Fredheim (2005), and Patursson (2008).
Net Deformation
Net deformation was estimated by determining the differences in net tag (12) locations
during slack, intermediate and fast tidal cycles. Three methods were used to calculate
changes in net volume and included the scalar triple product method, divergence method
and the signed volume method. These volumetric calculations, and complete results, are
summarized in DeCew et al. 2013.
33
Fish Swimming Behavior and Distribution
Visual diagrams of the net pen illustrate individual (Fig. 5 a, b), group (Fig. 5 c,
d) and density plots (Fig. 6) of the trout tracked horizontally and vertically. This allowed
for 1 hour visual examinations in on June 17 and 18th on low and high current flows.
There were no significant differences (unpaired t-test, P > 0.05) in fish positions relative
to the net walls and bottom during high and low currents, or during night and day
intervals (Table 2).
Fish were more clustered together during periods with fast current speeds (Fig. 6
a, b), and less clustered during periods with slow current speeds (Fig. 6 c, d). This
influence of current speed was also manifested in terms of cage utilization. The fish
utilized less of the net volume (6.71 m3) during high currents (Fig. 6 a, b) and utilized
more net space during slow currents (14.2 m3), (Fig. 6 c, d).
Mean swimming speeds ranged from ~ 0 - 0.6 BL/s, varied between individuals,
varied over time for any given individual, and were negatively correlated with current
speed. Swimming speeds were faster during low currents and slower during high
currents (Fig. 7). Swimming speed decreased with increasing current speed because the
fish displayed rheotaxis, and simply held their position against the current. Because
current speed affected swimming speed, for day/night comparison of swimming speed,
we used data sets collected during different times of the day, but which had similar
current speeds. The comparison was made using data collected from the same four fish at
night on June 17 (0200-0300h) and during the day on June 26 (1100-1200h). Current
speeds were similar in the two time intervals (0.19 and 0.16 m/s day and night,
34
respectively). There was no significant difference (unpaired t-test, P=0.53) between
mean day (0.178 BL/s) and night (0.178 BL/s) swimming speeds (Fig. 8).
Mean (±SD) swimming depth, based on the same fish sampled during the
indicated time intervals in Table 2 ranged from 2-3 m, and did not differ over time
(ANOVA, p=0.82).
Discussion
The HTI biotelemetry system is a powerful acoustical tracking instrument that
holds promise for monitoring fish and net movement in real time. The UNH pilot scale
cage served well to evaluate the usefulness of the HTI system on a sea cage with
steelhead trout. Acoustic biotelemetry systems have been used in the past to monitor fish
movement (Bjordal et al., 1986; Floen et al., 1988; Kils, 1989; Juell et al., 1993; Begout
Anras & Lagadere, 2004; Rillahan et al., 2009, 2011) however they have not been used to
measure fish distribution relative to net deformation. In this study we examined how the
fish reacted to changes in the net environment during high and low tidal cycles, with
associated high and low currents. This and our companion study (DeCew et al. 2013)
revealed that nets did deform at high current speeds, which reduced the cage volume and
forced fish to reposition themselves. As expected, the trout tended to swim into the
current when it flowed at a high speed, and thus their position in the net pen was guided
by their reactions to both the current speed and direction, and net deformation. Current
flow inside the net was significantly reduced (32-53%) compared to outside current
velocities. We suspect volume deformation, at a given current speed, was even greater
with the addition of fouling communities over time. These results were similar to those
35
reported by Lader et al. (2008), who measured net volume reduction at two farms in
Norway, and reported that at one site, a current of 0.13 m / s resulted in 20% loss in cage
volume. At the other site, a current speed of 0.35 m / s caused a 40% net volume
reduction.
In contrast to steelhead trout, numerous studies have been conducted on Atlantic
salmon swimming behavior in larger sea cages (Sutterlin et al., 1979; Juell et al., 1993;
Magurran, 1993; Juell, 1995; Johansson et al., 2009; F0re et al, 2009; Oppedal et al.,
2011). Because of their larger volumes and depths, larger cages often have temperature,
salinity, oxygen, current speed and light gradients (Juell, 1995; Juell & Fosseidengen,
2004; Johansson et al., 2006, 2007; Oppedal et al., 2007), all of which can affect the
distribution and movements of the fish. Interactions between individuals, and the net
walls, also influence the behavior of the group (Fore et al., 2009). In general, fish occupy
areas where the suite of environmental conditions are optimal, and avoid the net walls.
Such gradients, and choices, were not present in our small cage, so it seems unlikely that
variables such as temperature, salinity, or dissolved oxygen affected our results. We did
observe positive rheotaxis (Dodson & Mayfield 1979), at high current speeds, and more
circular swimming patterns at slower speeds, which is similar to the observations of
Atlantic salmon (Kils, 1989; Pitcher et al., 1993; F0re et al., 2009). It has been shown that
in natural streams, orientation, depth, and area occupied by trout can change with current
speed (Pert & Erman, 1994). When current speeds were > 0.2 m/s, the trout generally
swam into the current and occasionally some would change direction and orient tail to the
current before circling back.
36
We found no significant differences between night and day swimming depths.
These results differ from those described by Cubitt et al. (2005), Johansson et al. (2006,
2007, 2009), Dempster, et al. (2008), and Korsoen et al. (2009). In those studies, Atlantic
salmon swimming depths appeared to be controlled by changes in light intensity. Salmon
descended at dawn, stayed deeper during the day, and then ascended at dusk to swim
closer to the surface. Our differing results were probably due to our small volume (63
m3), and shallow depth (4 m) sea cage, which may well have restricted normal diurnal
rhythms. Moreover, if the daily vertical migration is associated with light, the light levels
between the top and bottom of our small net pen only differed by a small amount. As
with Huse et al. (1993), Juell et al. (1995), and Femo et al. (1995) the fish avoided the net
sides and bottom as an anti-collision behavior.
Mean swimming speeds of the trout ranged from - 0 - 0.6 BL/s, which is similar
to the range seen in Atlantic salmon held in net pens (Oppedahl et al. 2011). The activity
of rainbow trout (mean weight 254 g), measured as average hourly distance traveled, was
reported by Begout Anras & Lagadere (2004). They found that fish held at their lowest
density (27 kg / m3) were more active during the day. We saw no statistical difference
between day and night swimming rates, but it is difficult to compare our results to theirs
because of differences in fish size, stocking density, containment structure, net volume
and current velocities.
Although the HTI system proved useful in this environment, it was not without its
problems. Enormous amounts of fish and cage positional data were collected during the 4
week study, but not all the data could be used. The tags used were all pinging at the same
frequency, but with different periods. Therefore, because of the number of tags in use at
37
one time, there were often overlaps among the 20 tags, which prevented us from
distinguishing individual tags at every moment. In addition, the small size of the
experimental cage, and thus the close proximity of the hydrophones, made it more
difficult to triangulate signals. Triangulation uses the time of arrival differences between
the different hydrophones to calculate the distance from the pingers to each hydrophone.
If they are close together, as in our situation, the time of arrival differences are very small
and this led to some loss of data that had a poor resolution. Another issue that may have
complicated data collection was vibration of the hydrophone posts during strong currents
and when fouled with marine seaweed and debris. While equipment set up (hydrophone
location), cabling and HTI containment would be more challenging at a remote, deep
water site, the results would likely improve on a larger scale cage with increased
distances between transmitter and hydrophones.
In summary, the HTI system was used successfully too simultaneously, and
accurately, monitor both the shape and volume of a net pen, and the fish within it. As
such, we believe it has great potential as an aquaculture research tool that can lead to
improvements in net design, mooring systems, and fish welfare.
38
Table 2.1. Environmental ranges at the experimental site during the study period (June 2010)._________________________________________________________________________________
Parameter
Oxygen:Temperature:Salinity:Tidal amplitude (relative to MLLW) Current speed outside the net (ADCP) Current speed inside the net (MAYS)
Range
7.7 - 10.3 ppm11.3 -16.9°C (3-4°C on tidal change) 26 - 33 PSU -0.3 to 3.3 m 0 - 0.50 m / s 0 - 0.37 m / s
39
Table 2.2. Mean distances of trout from net tags (one up current and one down current) during four sampling periods. There were no significant differences (unpaired t-test, P > 0.05) in distances relative to the net walls and bottom during high and low currents, or during night and day intervals. This indicates that fish were evenly distributed in the cage during slow and fast currents, and during the night and dav.__________________________________________________
CurrentSpeed(m/s)
Mean distance of fish to tae (m) Date Hour
# of fish
Net tag location
Day slow 0.083 2.32 6/26 1100 3 up currentNight slow 0.138 1.82 6/17 1400 4 up currentDay slow 0.083 2.32 6/26 1100 2 down currentNight slow 0.138 2.78 6/17 1400 4 down current
Day fast 0.52 1.45 6/18 0800 5 down currentNight fast 0.37 1.45 6/29 1900 5 up currentDay fast 0.52 2.84 6/18 0800 5 up currentNight fast 0.37 2.91 6/29 1900 5 down current
A. B.
Figure 2.1. Google Earth photos of Fort Point, New Castle, NH, USA and the Judd Gregg Marine Research Pier (A). The boxed in area (in A) magnifies the UNH Pier and experimental cage site (B).
41
Hydrophone mounts
Hydrophone^)
Weighted tower rim
Acoustic source location
Figure 2.2. Experimental cage design showing placement of the 4 HTI hydrophones and 12 net pingers (acoustic sources). Also shown is the Modular Acoustic Velocity Sensor suspended in the middle of the net. Positioning of the hydrophones at two different depths allows triangulating the position of fish in 3 dimensions.
42
1 uu>dd ~ ^ ' Y
% K
*
Figure 2.3. An HTI model 795Z acoustic transmitter (left) being implanted into the abdominal cavity of a steelhead trout (right).
43
outsid«ci|« (A O C 9)> M lid ttn«6/ 4/2010
04
0 3
C 0.15 U
01
20 24
Time
Figure 2.4. An example of current velocities at the test cage site during ebb and flood tides. Currents were measured inside the cage with a Modular Acoustic Velocity Sensor and outside the cage, 10 m away, with an Acoustic Doppler Current Profiler.
44
a. Top View of Middle Net Tags and Single Fish b. Side View o f Middle Net Tags and Single Fish
d. Side View o f Middle Net Tags and Four Fishc. Top View of Middle Net Tags and Four Fish
Figure 2.5. An illustration of a single fish (a, b), and group of four fish (c, d), tracked on June 17 during at a current speed of 0.14 m / s. Red dots indicate the location of the net tags.
45
Side View Current FlowCurrent Flow
Top MewSide View
Current flow Current flow
Figure 2.6. Density plot showing the distribution of a single trout on June 18 from 0800- 0900h, when the current velocity was 0.50 m / s (ebb tide). Panel a. is a side view of the cage while panel b. is a top view. During this one hour event, the fish used 6.71 m3 (10.6%) of the available net environment. Panels c. (side view) and d. (top view) depict the density plot of three trout during a slack tide (0.083 m/s) on June 26 at 1 lOOh. During slack tide, the fish used 14.2 m3 (22.5%) of the net environment. The mean weight of the fish was approximately 600g.
46
0.6 . - - - - - - - - - - - - - -- -■ —.... -. . . -. . . . . -
# Swim speed (BL/s) = 0.25-0.35 current speed (m/s)0.5 - • * 10.4
0.3 - •
0.2•9' -. t + . — 4 i + !
0.1 I : *w w
% •
0 - •0.00 0.05 0.10 0.15 0.20 0.25 0.30
Current speed (m/sec)
Figure 2.7. Relationship between swimming speed (BL / sec) and current speed (m / sec) recorded by a Modular Acoustic Velocity Sensor (MAVS) current meter that was suspended inside the fish cage. The slope of the line (-0.35) was significantly different than zero (Regression analysis; P=0.01).
47
Mea
n (±
SD)
swim
0.250
0.200
0.150
0.100
0.050
0.000
Day Night
Figure 2.8. Mean (±SD) swimming speeds (BL / sec) of the same seven fish during day (1400-1500h) and night intervals (0200-0300h) on June 18th.
48
CHAPTER n i
SUBMERGED CULTURE OF STEELHEAD TROUT Oncorhynchus mykiss FOR
OPEN OCEAN AQUACULTURE IN THE NORTHEASTERN UNITED STATES
Abstract
To meet growing seafood demands, the US aquaculture industry will need to
consider farming the open ocean in a responsible manner. However, offshore
environments can be energetic (seas > 8 m) and difficult to maintain surface cage
systems. To minimize potential storm damage, submerged culture technologies can be
employed to safeguard the infrastructure and product. Steelhead trout (Oncorhynchus
mykiss) have potential as an offshore species, though they have open air bladders
(physostomous), and need access to air to inflate their swim bladders. To address this
concern, three experiments were developed to explore the ability of O. mykiss to cope
with extended periods of submergence.. The studies used small (~300 g) and large
(~1000 g) trout, in cages that ranged from 3.7 to 68 m3, that were submerged for periods
of one to four weeks. Data storage tags (DST), sonar and video were used to quantify
their ability to manage with submergence. Results indicated differences in growth,
condition, and mortality among the treatments. The study suggests O. mykiss can be
submerged for days to weeks with no negative effects.
49
Introduction
The New England ground fishery has nearly collapsed because of overfishing and
habitat loss (Hennessey and Healey, 2000). This shortage has stimulated new ideas to
produce seafood and to provide economic opportunities for harvesters that have, or will,
become displaced from traditional fisheries (Hennessey and Healey, 2000). Among the
most logical of the long-term solutions is the further development of marine aquaculture,
which has the capacity to produce the needed seafood, provide economic opportunities
for displaced harvesters, and contribute to economic and community development,
particularly in New England.
It is widely accepted that new marine aquaculture development in the US will
occur offshore in less populated waters. The US government has attempted to facilitate
this by developing the National Offshore Aquaculture Act of 2005. In addition, regional
centers throughout the US (NH, HI, CA and FL) were funded in to explore hatchery,
nursery and grow out technologies for cage culture (Benetti, et al., 2010; Fredriksson, et
al., 2004; Tsukrov, et al., 2000; Chambers and Ostrowski, 1999 and Tamaru, et al 1998).
New marine finfish species, both temperate and tropical were successfully spawned,
raised in hatcheries and made available for ocean growout. Submerged cages (Sea
Station™) were preferred to help protect juvenile fish after they were transferred offshore
from turbulent conditions (e.g. wind and waves) at the surface. This later proved to be a
benefit in growout to escape winter storm events and hurricanes. Other benefits of
submerged culture were less ware on the culture system, more stable temperatures, and
less bio-fouling on the nets (Chambers and Howell, 2006).
50
Rainbow trout (O. mykiss), called steelhead when they transfer from fresh to salt
water, are commercially grown in protected waters in Chile, Norway, Faroe Islands,
Canada, and to a limited extent in the USA (Washington and New Hampshire). Steelhead
trout have great potential to succeed as an aquaculture species in New England. First,
they have been domesticated for >150 years and are the basis for recreational fisheries
and fresh water aquaculture throughout the world. As a result, juveniles are readily
available from numerous commercial hatcheries. Second, unlike Atlantic salmon, O.
mykiss does not go through true smoltification (internal metabolic processes that allows
fish to migrate from fresh to seawater), so juveniles can go directly from a freshwater
hatchery to full strength seawater (32 ppt.). Third, the species has a relatively fast growth
rates in sea cages, reaching marketable size (1-3 kg) in 8 months after stocking at 250g.
Finally, they are disease resistant, are more temperature tolerant than Atlantic salmon,
and have a high market value (>13.00 / kg).
Submerged cage culture has been successfully demonstrated for several species,
including Atlantic salmon (Oppedal et al., 2011; Dempster et al., 2008, 2009; Korspen et
al., 2009), Pacific threadfin (Ryan 2004), cobia (Rapp et al. 2007), Atlantic cod and
haddock (Chambers et al., 2006, 2007; Rillahan et al., 2009, 2011), and halibut (Howell
et al., 2005). Because suitable inshore aquaculture sites are becoming scarce, and winter
icing and storms can damage surface cages, there is growing interest in culturing
salmonid species in offshore, submerged sea cages. In addition to providing more
locations and avoiding ‘visual pollution’, submerged systems could reduce the risk of fish
escapees during storms (Naylor et al., 2005), and sea-lice infestations (Hevrpy et al.,
2003). Despite these advantages, submerged systems for salmonids are only beginning to
51
be considered, and much of the essential knowledge on how submergence will affect the
fish is lacking.
The uncertainty surrounding submergence is related to the assumption that
salmonids become negatively buoyant when submerged beneath a cage roof because they
cannot access the surface to gulp air to fill their swim bladders (Smith, 1982). Near shore,
sea cage studies in Norway demonstrated that Atlantic salmon cope with submergence
quite well (Oppedal et al., 2011; Dempster el al., 2008, 2009; Korspen et al., 2009;
Osland et al., 2001). They feed actively and grow well, albeit at a slower rate than those
in surface cages. Dempster et al. (2008) found that 1.7 kg salmon increased their
swimming speeds by 1.5 times when submerged, compared to fish in control cages, and
suggested that the slower growth was due to the increased energetic expenditure for
swimming. They noted, however, that temperature and light differences between fish held
in surface cages, verses deeper submerged cages, may also have contributed to the
observed growth differences.
To investigate the ability of steelhead trout to incur periods of submergence, three
experiments were conducted to test the null hypotheses that the behavior, growth,
incidence of fin damage, and mortality in submerged cages does not differ from trout
held in surface cages under similar environmental conditions.
Methods and Materials
Timing and Locations
The project lasted 24 months, and involved three separate, but related,
experiments. In the first, which occurred from June through August 2011, we studied
juvenile trout in small inshore cages located near the University’s Judd Gregg Marine
52
Research Pier (JGP) in New Castle, NH (Fig. 1). The second experiment took place from
October through December 2011, in the same location. This time, larger trout and cages
were used. The third and final experiment was conducted in the summer of 2012 (June -
August), at a study location ~ 0.8 km seaward from the JGP that had more exposure to
wind and waves.
Steelhead Trout
In all three experiments, juvenile steelhead trout were purchased from Sumner
Brook Trout Farm in Ossipee, NH. Sumner Brook acquires eyed eggs from Trout Lodge
in Sumner, WA. that were certified disease free and are all diploid. Fingerlings were
raised in flow through, freshwater raceways for 8 months to a size of ~ 150 g. Prior to fish
transfer to sea cages, the trout were fed a 3 mm, Skretting Bio-Transfer diet for 7 days.
This diet helps transition salmonid smolts from fresh to salt water environments. It has
elevated dietary salts that encourage the development of osmoregulatory ability, while
added betaine acts as an osmoprotectant by relieving gastrointestinal stress. Fish were
transported to the Jackson Estuarine Marine Lab in Great Bay, NH in insulated 1 m3
containers. Here, they were acclimated from freshwater to brackish bay water (20 ppt.) in
flow through, fiberglass tanks for two weeks. They were then moved to a sea cage near
the JGP for final acclimation to 30 ppt.
Fish were hand fed to satiation daily with a sinking, Bio Oregon Trout diet (45%
protein, 24% lipid), trout in submerged cages were fed through a flexible PVC hose that
extended from the surface down into the center of each cage 1 m. Underwater video
cameras were used to help determine feeding satiation in these treatments.
53
Because environmental variables can influence swimming behavior and depth of
salmonids (Johansson et al., 2006, 2007; Oppedal et al., 2001, 2007), we collected a
series of environmental measurements. HOBO® temperature loggers were installed 1 m
below the surface of each cage and an YSI 6600 V2-2 Water Quality Sonde, located at
the end of the pier adjacent to the cage site, collected additional environmental data
(temperature, dissolved oxygen, salinity, pH, tidal amplitude and turbidity). Lastly,
current speeds were measured weekly in each cage, at 1 m depth intervals. Finally,
mortalities, if any, were recorded daily.
Experiment 1
In experiment 1, six, 3.75 m3 cylindrical cages (Fig 2a.) were constructed from a
2.5 cm mesh Seawire™ netting. Seawire is a stiff, copper alloy net material that
minimizes bio-fouling that can reduce water flow and quality (Chambers et al., 2012). On
10th June 2011, each cage was stocked with 55 trout with a mean (± SEM) starting weight
of 255.6 (14.4) g and length of 27.6 (0.4) cm. The experimental design had two
treatments (A & B) and a control (C), each with two replicates, for a total of six cages.
Control cages (C1 and C2) were maintained at the surface throughout the study to allow
fish to gulp air. Treatment cages, each equipped with a nylon netting cover, were
submerged 1 m during the study to prevent fish from accessing the surface to fill their gas
bladders (Fig 2b.).
The replicate treatment cages Al and A2 were submerged for two weeks, brought
to the surface for one day, re-submerged for two weeks, brought to the surface for one
day, etc. until the experiment was complete after 8 weeks. The replicate treatment cages
B1 and B2 were submerged for 4 weeks, brought to the surface for one day, re
54
submerged for the next 4 weeks, and then brought to the surface at the end of the
experiment.
Data from replicate pairs were compared, and because there was no difference in
any of the measured variables (Mann-Whitney U tests, P > 0.1), data from the replicate
pairs were combined.
Experiment 2
In the second phase of the submergence project, two 68 m3 floating cages were
deployed at the aforementioned inshore site. Each of the 4.6 x 4.6 x 3.2 m cages were
constructed of 2.5 cm knotless nylon twine, and were supported at the surface by high-
density polyethylene floating frames with wooden walkways (Fig. 3). The control cage
was maintained at the surface so the trout could freely gulp air to fill their swim bladders
(Fig. 3. A.) while the treatment cage (submerged) had a nylon mesh net roof to retain the
fish from surfacing (Fig. 3. B.). These were then submerged 1 m below surface for
sequentially greater periods of time using a series of ropes and weights attached to the to
the float platform.
The second experiment began in October 2011, using fish retained from
experiment 1. Each cage was stocked with 84 trout with a mean (± SEM) weight of
1070.4 (53.7) g and a mean length of 41.3 (0.7) cm. The experimental design had a
single treatment (submerged) and a single surface control. Prior to the start of the
experiment, a random sample of 10 fish from the control and treatment cages were
captured, anesthetized, and fitted with electronic data storage tags (Star-Oddi™ tilt tags).
These tags, as shown in Figure 4, were attached externally, just anterio-laterally of the
dorsal fin. They recorded temperature (° C), depth (m), pitch angle (degrees head up or
55
head down) and roll angle (degrees side-to-side) at either 45 (pitch and roll) or 90
(temperature and depth) second intervals. To test tag retention and survival, six trout
were placed into a 2 m round fiberglass tank with flow through water at the UNH Coastal
Marine Laboratory (CML). Three of the trout were surgically implanted with dummy
Star-Oddi tags while the remaining three fish were not tagged. After 1 month, all six fish
had adapted to the tank, were feeding well and the three tags were still attached firmly to
the trout.
Delays with the cage manufacturer extended the trial into the fall. With
decreasing winter temperatures causing a cessation in feeding (< 5°C) and problems with
the DST tags becoming fouled in the net, the submergence schedules had to be modified.
Instead of the 2, 3 and 4 week schedule, the treatment cage was submerged for 17 days,
brought to the surface for 4 days while we reattached the data storage tags, and then re
submerged for 31 days (Nov. 4 through Dec. 5 ).
Experiment 3 (Exposed site)
In the second year of the research, the two inshore cages used in experiment 2
were towed seaward to an exposed location approximately 0.8 km from the original site.
Steelhead trout ~100 g were purchased in early May 2012 and held at the UNH Jackson
Estuarine Lab for 2 weeks to help transition them to brackish bay water (20ppt). In early
June, they were transferred to the UNH JGP (full strength salinity - 30ppt). They were
held in a net pen at the pier until they had increased to a mean weight of 308.1 g (+/-
81.1) and mean length 28.1 cm (+/- 1.8). Fish were transferred to the experimental pens
(200 / cage) on June 19th, and on June 20th, the treatment cage was submerged 2 m below
surface. Again, one cage served as a control and was maintained at the surface. The
56
experimental pen was raised to the surface on June 27th, one week later and the first set
of data was collected from fish (n = 25) in both the submerged and surface cages.
Following this 24 hour surface time, the cage was submerged for sequentially longer
periods of time (2, 3 and 4 weeks), each separated by 24 hours at the surface.
To quantify the fish swimming angles, a weighted vertical white line was placed
in the center of each cage to a depth of 1 m off the net bottom. A Go-Pro™ video
camera, mounted on a 2.3 m PVC pole, was lowered into each cage and attached to the
side net for 30 minutes on each sampling date. Video was captured as the fish passed by
the vertical white line, and later analyzed with Ethovision XT fish tracking software to
determine mean tilt angle as the fish moved past the vertical line.
Growth. Condition and Fin Damage
Fish were sampled bi-monthly throughout each experiment. A random sample of
25 fish from each cage was anesthetized with MS222, weighed and measured. Standard
indices of growth and condition were calculated for each sampling date. Specific growth
rate (SGR, % day'1) was calculated as ((In (W2 ) - In (W))) / (t2 -ti)) x 100, where W2 and
Wi are the mean live body weights at times t2 and ti, respectively. Fulton’s condition
factor (K) was calculated with the formula K = ((W/L3) x 100), where W is the wet
weight (g), and L is the total length (cm). During scheduled resurfacing of the treatment
cages, fish in both control and treatment cages were visually examined for fin damage
and/or snout abrasions that can be caused when the fish encounters the cage ‘roofs’ as
they try to surface to obtain air and refill their swim bladders. The degree of snout
damage was assigned using a subjective index from 1 (undamaged) to 5 (extreme
damage) based upon Hoyle et al. (2007).
57
Surface Rolling and Jumping Behavior
Jumping and rolling behavior of both the control (surface) and treatment
(submerged) cages were observed each time the treatment cages were brought to the
surface. When the treatment cages were raised, the total number of jumps and rolls in all
cages, during the first 30-min period, were counted. All counts were standardized to rolls
or jumps fish'1 h r_1 (e.g. Furevik et al., 1993; Juell & Fosseidengen, 1995).
Statistical Analyses
In Experiment 1, statistical analyses varied with experimental design. On those
dates when only one of the submerged treatments was brought to the surface,
comparisons to the control (surface) fish were made with Mann-Whitney U tests. On
those dates when both submerged treatments were resurfaced, either one-way ANOVA,
followed by Tukey-Kramer multiple comparison test, or a Kruskal-Wallis test, followed
by Dunn’s Multiple Comparison test (if the data were not normally distributed) were
used. Response variables compared included fish length and weight, survival percentage
(square root arcsine transformed), incidence of fin, snout and body injuries, and
condition. In Experiments 2 and 3, where there were not statistical replicates, differences
in the same response variables between treatments were compared using Mann-Whitney
U tests.
Results
Experiment 1
After 18 days of submergence, the fish in the surface cages (C) were significantly
heavier than those in the submerged cages (A) and also were in better condition (heavier
58
per unit length; Table 1). There were no differences in mean length or abrasions on the
snout between surface and submerged fish. On the second sampling date both treatments
(2 and 4 weeks submergence, A and B respectively) were sampled, along with the control
(surface) cages (C). There were no significant differences in mean lengths or snout
condition (ANOVA, P > 0.05) between treatments, or between treatments and the
controls. Fish in the surface (control) cages were significantly heavier than those
submerged for 2 weeks (P < 0.05), but no different than those that had been submerged
for 4 weeks (ANOVA, P > 0.05). There was no difference in the condition of the fish
submerged for 2 and 4 weeks (ANOVA, P > 0.05), but the condition of the control
(surface) fish was significantly higher that both treatments (ANOVA, P < 0.05). On the
third sampling date fish in the control (surface) cage were significantly (Mann-Whitney
U-test, P < 0.05) heavier, longer, and in better condition than those in the 2 weeks
submergence treatment (A). There were no differences, however, in snout abrasions
(Mann-Whitney U-test, P > 0.05) between the treatment and control fish. At the end of
the experiment, on August 11th, fish in the surface (control) cages were significantly
heavier and longer than those in both of the treatment cages (ANOVA, P < 0.01). Fish in
the control cages (C) were also in significantly better condition (ANOVA, P < 0.001)
than those in the 2 weeks submergence treatment (A), but not better than those in the 4
weeks submergence (B) treatment (ANOVA, P > 0.05). There was no difference in
condition between fish in the two treatments, or between nose abrasions in the fish in two
treatments and the control (ANOVA, P > 0.05). Overall, trout in the control cages had
significantly better weight, length, condition and less nose abrasions than fish that were
submerged for 2 weeks and 4 weeks.
59
At the end of the 2 and 4 week intervals, trout in the submerged cages were
brought to the surface. In all cases, fish that had been submerged, jumped more
frequently than control (surface maintained) fish, presumably to fill their depleted swim
bladders with air (Fig. 6).
Mean (+/- SE) survival rates for treatments A and B, and the control (C), in
Experiment 1 were 66.4% (+/-6.3), 40.9% (+/-10.0), and 90.9% (+/- 5.4), respectively
(Fig. 7). After square root arcsine transformation of these data, an analysis of variance
(ANOVA) found that the means were not significantly different (P > 0.05). The
relatively low survival in Treatments A and B were caused by either bacterial or viral
infection, characterized by skin lesions, and perhaps exacerbated by the periodic
submergence of these two treatments.
Trout survival was the lowest during the two week submergence period. This may
be due to the additive handling and submergence over the eight week trial.
Specific growth rates (SGR) were calculated for fish in each treatment (A, B) and
the control (C) in both Experiments 1 and 2 (Table 2). In Experiment 1, growth rates
were highest in the surface control fish (C), intermediate in the 4 weeks submergence
treatment (B), and lowest in the 2 weeks submergence treatment (A). The lower growth
rate of fish in the 2 weeks submergence treatment compared to fish in the 4 weeks
submergence treatment may have been due to the stress associated with more frequent
handling during sampling.
Experiment 2
In experiment two, 17 days after submergence, there were no differences in mean
weight, mean length, mean condition or mean nose abrasions between surface and
60
submerged fish (Mann-Whitney U-tests, P > 0.05; Table 3). However, on the final
sampling date, after the treatment fish had been submerged continuously for 31 days, fish
held at the surface (control) were significantly heavier than fish that had been submerged
(Mann-Whitney U-test, P < 0.05). In fact, surface fish gained weight more than twice as
fast as submerged fish. There were no significant differences in mean length, mean
condition or mean nose abrasions between surface and submerged fish (Mann-Whitney
U-tests, P > 0.05).
On both sampling dates, fish that had been submerged jumped more frequently
than control (surface maintained) fish, presumably to fill their depleted swim bladders
with air (Fig. 6).
Survival was good in both the surface (88%) and submerged cage (92%). No
statistical comparison was possible due to single replicates, and the cause of death from
the few fish that died is unknown.
As indicated above, the pitch and roll tags were attached externally (Fig. 4.)
because internal (surgical) placement would have made it difficult, if not impossible, to
get the pitch and roll axes of the tag aligned with the same axes of the fish. Because the
tags were external, some became snagged in the cage netting, effectively changing their
orientation relative to the axes of the fish. For this reason, pitch and roll data from
several of the tags was suspect, and therefore not used.
While acute pitch angles (20-30°) were common as the individual fish moved up
and down in the cage, mean weekly pitch angle did not change over the course of
experiment 2, in either the surface (control) or submerged cages (Fig. 7). Mean weekly
pitch angle in fish held in both the surface and submerged cages varied from -3° to +3 °.
61
If submerged fish were compensating for lost buoyancy by swimming upward, we would
have expected a ‘heads up’ (+) orientation to develop over time, but this was not
apparent.
Experiment 3
Results were similar in the 1, 2, and 3 week submergence periods and can be
found in Table 4. Mean lengths did vary between the surface and submerged treatment
during week one and week two periods. During the first week submergence, the surface
cage was significantly longer that the submerged cage. This reversed during the second
week submergence with the submerged fish becoming significantly longer than the
surface. After this point, length, weight, specific growth rates (Table 2) and body
abrasions were all similar.
Most notable in Experiment 3 was survival and jumping events (upon resurfacing)
during the third and fourth week submergence trials. At samplings 1 and 2 weeks after
submergence, survival was similar at 99% (surface) and 98% (submerged). After 3 weeks
submergence, the survival was again similar at 83% and 84% respectfully. A divergence
occurred after 4 weeks submergence with a survival of 74 % in the surface and 43% in
the subsurface cage (Fig. 6). Also interesting was jumping events decreased when the
trout were resurfaced at the third and fourth intervals perhaps indicating that fish in both
cages were under stress (Fig. 8). During this time period, high temperatures (> 16°C) and
heavy bio-fouling of the hydroid Tubularia recruited onto the net and cage frames.
Ethovison XT fish tracking software was used to analyze the underwater video of
trout swimming angle past a vertical line suspended within the center of the cages.
Results indicated no differences in swimming angle + 3° in both the control and treatment
62
cages.
Discussion
The three experiments conducted to test differences between steelhead trout held
in surface verses subsurface cages showed varied results. At the end of Experiments 1
and 2, fish maintained at the surface were significantly heavier than those in submerged
cages, but in Experiment 3 there were no differences. Location and cage size may have
been responsible for these observed differences. Experiment 1, done with relatively
small fish (-300 g), was conducted in small diameter (1.25 m), cylindrical copper-alloy
cages at an inshore site exposed to fast tidal currents (0.5 m / s). Snout damage was
severe in all treatments and more so in the submerged cages, probably because of the
small cage size and copper-alloy cage material. Submerged fish may have incurred more
nose abrasions in trying to reach the surface to access air. Survival was poor in the
submerged cages, suggesting that the stresses of snout damage and submergence were
additive.
In Experiment 2, fish (-1000 g), and cages (68 m3) were larger and made of soft
nylon mesh, snout damage was virtually non-existent, and survival was good in both the
surface and submerged cage. At the conclusion, surface fish were significantly heavier,
indicating that submergence alone can have negative effects on growth performance. It
should be noted, however, that fish were submerged for 31 days, which is probably a
longer time than would be necessary in an aquaculture application that would avoid a
storm, phytoplankton and jellyfish bloom and or warm surface temperatures during the
summer (> 16°C). The mechanisms for compromised growth, however, remain elusive.
63
We saw no change in the swimming angle and vertical depth, which would have
suggested severe swim bladder depletion as reported by Dempster et al. (2008,2009) and
Korsoen et al. (2009).
In the third experiment, with smaller trout again, 1 and 2 week submergence
period indicated now significant differences between the surface and subsurface cages.
However, during the 3 and 4 submergence periods, survival and jumping changed
significantly in both treatments that may have been brought on by changes in the cage
environment. The cause of this was probably due to warm water temperatures (> 16°C)
and heavy bio-fouling of Tubularia on the nets. Tublaria has a flowery head with
stinging nematocysts that can irritate the outer mucous membrane of fish (Fig. 9).
Anecdotal evidence has shown this to be more of a problem during July and August when
surface water temperatures can reach up to 20°C. The trout were not vaccinated in any of
the above experiments that may have safe guarded them during this exposure. Secondary
bacterial infections caused by stress (temperature and bio-fouling) may have altered
survival rates and jumping behavior. An indication of this stress can be seen in the
jumping data in Figure 6. Here, jumping in both cages decreased by the end of the
experiment.
While we do not have conclusive data, we believe that steelhead trout can be
submerged for days to weeks with no negative effects, and this is an important finding for
those interested in culturing this species. We were logistically unable to conduct the
experiments in deep (> 10m) water, and hence our submerged cages, while below the
surface, were still relatively shallow. Because pressure (depth) may have an effect on the
behavior and physiology of forcibly submerged fish, these experiments should be
64
repeated in cages submerged to greater depths (> 10 m) in open ocean conditions.
Duration of successful submergence will depend on the species, size, temporal season,
and depth (Dempster et al., 2008, 2009).
Ultimately, cage submergence can be used as an effective management tool to
temporarily escape adverse situations at sea. The additional cost associated with
submergence must be taken into consideration by farmers and balanced out with the
potential risk of maintaining live stock at the surface. As fish farming expands offshore,
it will be important to develop management tools that can measure fish welfare, biology
and oceanographic data in real time. With this, farm managers can react appropriately to
safeguard their product in varying ocean conditions.
65
T able 3.1. M ean w eights, lengths, cond itions and nose abrasion ind ices o f the fish in the 2 w eek subm ergence treatm ent (A ), the 4 w eek subm ergence treatm ent (B ) and the surface contro l (C ) on the sam pling dates in E xperim en t 1. C om parisons betw een fish in the treatm ents and con tro l, fo r each o f the lis ted response variab les, w ere m ade w ith e ith er M ann-W hitney U -tests (June 29 and Ju ly .29) o r A nalysis o f V ariance (Ju ly 14 and A ugust 1U.____________________ ;_________________________________________________________________________________
S am plingD ate T reat
M ean w eight (s)
M eanlength (cm )
M eancondition
M eansnou t
6/29/2011 A 328.9 ± 10.4 29.5 ± 0 .26 1.26 1.7C 360.5 ± 9 .8 29 .6 ± 0 .2 6 1.37 1.5
C om parison C > A ( P < 0 .0 5 ) A = C /P < 0 .05) C > A f P < 0 .0001) A = C (P > 0.05)
7/14/2011 A 372.1 ± 12.9 30.6 ± 0 .2 8 1.27 1.9B 377.2 ± 1 3 .8 30.7 ± 0 .3 0 1.28 1.6C 414.7 ± 14.9 30.9 ± 0 .3 1 1.37 1.7
C om parisons A = B (P < 0 .05) C > A (P < 0 .05) C = B (P > 0 .05)
A = B = C (P < 0 .05) A = B (P < 0 .05) C > A ( P < 0 .0 1 ) C > B fP < 0 .01)
A = B = C (P < 0 .05)
7/29/2011 A 404.5 ± 6 3 .9 31.4 ± 4 .9 1.25 1.6C 498 .2 ± 7 .3 8 32.8 ± 0 .3 7 1.39 1.7
C om parison C > A / p < o . o n C > A f P c O . O l ) C > A f P < 0 .0001) A = C (P > 0 .05)
8/11/2011 A 427 .2 ± 19.5 32.4 ± 0 .3 7 1.22 1.9B 459 ± 19.1 32.4 ± 0 .4 0 1.32 1.9C 560.5 ± 18.2 34.1 ± 0 .3 1 1.39 2.2
C om parison A = B (P > 0 .05) A = B (P > 0 .05) A = B ( P > 0 .0 5 ) A = B = C ( P > 0 . 0 5 )C > A ( P < 0 . 0 0 I ) C > A ( P < 0 . 0 0 1 ) B = C (P > 0.05)C > B f P < 0 . 0 1 ) C > B / P < 0 . 0 1 ) _____________ C > A ( P < 0 . 0 0 1 ) __________________________
Table 3.2. Specific growth rates (SGR (%/d)) of each of the indicated treatments at the end of Experiments 1.2 and 3._______________________________________________
Experiment Treatment Duration SGR f%/d)
1 A 8 weeks 0.8561 B 8 weeks 0.9761 C (control) 8 weeks 1.309
2 Submerged 7 weeks 0.3262 Surface 7 weeks 0.695
3 Submerged 10 weeks 1.163 Surface 10 weeks 1.33
67
Table 3.3. Mean weights, lengths, conditions and nose abrasion indices of the fish in the submerged and control cage on each of the sampling dates in Experiment 2. Comparisons between fish in the treatment and control, for each of the listed response. variables, were made with Mann-Whitnev U-tests._______________________________________________________
Sampling Mean Mean Mean MeanDate Treatment weight (s) length condition snout
10/27/2011 Submerged 1132.3 ± 58.9 41.5 ±0.66 1.59 ±0.08 1.0 ±0Surface 1183.8 ±67.4 41.0 ±0.79 1.73 ±0.13 1.2 ±0.2
Comparison Sub = Surf Sub = Surf Sub = Surf Sub = Surf2 week sub (P > 0.05) (P> 0.05) (P> 0.05) (P> 0.05)
12/6/2011 Submerged 1301.7 ±93.4 42.3 ±0.73 1.1 ±0.09 1±0Surface 1579 ±80.5 44.2 ±0.61 1.28 ±0.15 1 ±0
Comparison Sub < Surf Sub = Surf Sub = Surf Sub = Surf4 week sub (P < 0.05) (P> 0.05) (P> 0.05) (P> 0.05)
Table 3,4. G rowth and condition index fo r trout subm erged for 1 , 2 . 3 and 4 weeks during Experim ent 3.
DaleM eanLength (cm)
M ean W eight (g)
MeanCondition
Initial slock 6/19/12 28.14+1.83 308.17+81.08 1.0
Subm ersion6/27/12 Surface Submerged
29 .9± l.84 31.9+1.39SM fl^S S M te fg e d 376±95.I7 425.4+74.6
S u /ite e S u b m rs e d 1.38 1.3
Com parison (Unpaired t test)
Surface > Subm erged P>0.05
Surface = Submerged P<0.05
Surface = Submerged P>0.05
Tw o week Submersion
7/12/12 32.52+2.3 33.84±2 8 488 .8± 136.3 535.9+109.2 00
Com parison (Unpaired t test)
Surface < Submerged P>0.05
Surface = Submerged P<0.05
Surface = Submerged P>0.05
Three week Submersion
8/3/12 35.53+2.31 35.31+2.3 618.85+152.4 602.81+140.6 1.35 1.35
Com parison (Unpaired t test)
Surface - Submerged P<0.05
Surface = Submerged P<0,05
Surface = Submerged P>0.05
Four week Submersion
8/31/12 37.72±2.8 37.0+2.4 824.0+273.3 727.7±2!8.7 1.38 1.35
Com parison (Unpaired t test)
Surface = Subm erged P<Q.Q5
Surface = Submerged P<0.05
Surface = Submerged P>0.05
i \ p Mu - ) 1 9
} \ p. 'Nitt M
j f '
\ M l I'll t
fV-f
■#*/
N o ' l | ; n n p s h m M . t i i K
Figure 3.1. Aerial photo of the Judd Gregg Marine Research Pier in New Castle, NH and proximity of the experimental sites.
70
Figure 3.2. Cage design used in Experiment 1. Six, 3.75 m3 copper-alloy cages were suspended in a 4 x 5 m floating platform made of High Density Polyurethane (A). Diagram B. illustrates cage dimensions, the Control cage C (surface) and the submerged treatments cages A and B, one m below the surface to keep fish from refilling their swim bladders.
Figure 3.3. (A) Control cage left where trout were allowed access to the surface to gulp air. (B) Treatment cage with net nylon roof submerged 1 m below surface. Note feeding tube in upper left of image.
Figure 3.4. Steelhead trout (~ 1000 g) attached with a fitted Star-Oddi™ pitch and roll data storage tag.
Snout Damage Index
4 S
Figure 3.5. Visual representations of subjective snout index, ranging from no damage (1) to severe damage (5). Nose damage can occur when fish in the submerged treatments try to resurface to gulp air and fill their swim bladders.
74
1. 0.08
0.0?
0.06c1 0-051£ 0.04a
0.03i,
0 J02
0J01
0
IS urface S ubm erged
4 w eek s
2 . 0.100 0.090
| 0.080 | 0.070 |- 0.060 ,s 0.050 j s 0.040 fc 0.030
0.0200.0100.000
S urface S ubm erged
2 w eek s
I J 0 □Sab Sarf Sab Sab Sarf Sab Sarf Sab Sab Sarr
2 week 4 week 6 week 8 week
3 0.08
007
Figure 3.6. Number of jumps fish'1 minute"1 upon surfacing of submerged cages on the indicated sampling dates during the Experiments 1, 2 and 3.
75
Tagged fish #1017, Control cage
» • XU* « '
Fig. 3.7. An example of pitch recordings, taken from a fish in the submerged cage (Tag 1037-top) and a fish in the surface cage (Tag 1017- bottom), taken during the 5th week of Experiment 2.
76
10090
80
70
60
50
40
30
2010
0 I2 weeks 4 weeks
TreatmentSurface
2 .
>
taVi
1009080706050403020100
2 Week 4 WeekTreatment
• Surface i Submerged
3. 100
90
80
70
60
50Vip 40
30
20
10
■ Surface■ Submerged
1 week 2 week 3 week 4 week
Treatment
Figure 3.8. Survival of trout in Experiments 1, 2 and 3 at different submergence periods.
77
Figure 3.9. (A) Bio-fouling of the hydroid Tubularia on a fish net. (B) A heavily fouled net being pulled up for fish sampling.
78
C H A P T E R IV
TECHNOLOGY TRANSFER OF SMALL SCALE INTEGRATED MULITROPHIC
AQUACULTURE TO COMMERICAL FISHERMEN IN NH
Abstract
Over the last five years, the commercial fishing fleet in New England has been
subjected to increasingly restrictive management measures established to rebuild
declining stocks. By design, these measures have limited fishing opportunities and
significantly reduced the inshore small vessel fleet. To help support New Hampshire
(NH) fishermen, an extension program was developed by the University of New
Hampshire (UNH) and NH Sea Grant, to train fishers on small scale integrated multi-
trophic aquaculture (IMTA). Because federal and state regulatory agencies had concerns
about nitrogen input from fish production in the coastal waters of the state, a program
was designed to measure nitrogen uptake from shellfish and seaweed integrated with the
finfish production. The program was evaluated as the fishermen were taught the
necessary husbandry skills for culturing steelhead trout, blue mussels and sugar kelp
together. Nitrogen extraction by the mussels and kelp exceeded the nitrogen added from
trout production, and thus had a positive effect on the ecosystem. The training program
provided the fishermen with a new skill set, that they could adopt either part time or full
time, to provide additional income.
79
Introduction
Commercial fishing has been a vital component of New England’s economy for
over two centuries, and has grown to a half-a-billion dollar per year industry. Equally
important, recent economic studies based on National Marine Fisheries Service (NMFS)
data suggests that every job created in the seafood industry generates one-and-a-half jobs
in the regional economy: jobs in other sectors such as food processing, tourism,
restaurants and boatyards (Hoagland et. al 2005).
Over the last five years, however, the commercial fishing fleet in New England
has been subjected to increasingly restrictive management measures established to
rebuild declining stocks. By design, these measures have limited fishing opportunities
and significantly reduced the inshore small vessel fleet. The catch allocation groundfish
fishermen receive will result in a 40% decrease in potential landings, and may reduce the
current groundfish fishing fleet by 50% (NH Sea Grant, 2013). For many local
communities this will mean the loss of their historic fishing heritage. New Hampshire had
180 commercial fishing permits in 2009. The number declined by about 50% from 2009
to 2010, and the value of New Hampshire’s landings decreased by approximately 40%
(NH Sea Grant, 2013).
As fishers become displaced by federal management measures, they could adopt
small-scale aquaculture operations. They have vessels, water front infrastructure, and
experience working on the ocean, all of which would be useful in transitioning to
aquaculture. Although we envision that such a transition would be gradual for any given
individual, aquaculture could eventually become full time employment for some. It is
80
worth noting that the US is the third largest consumer of seafood in the world, yet we
import over $10 billion annually. Marine aquaculture has the potential to contribute to US
seafood production, reduce our reliance on imported seafood (FAO, 2010), and provide
economic opportunities to displaced fishers.
UHN established an Open Ocean Aquaculture research farm in 1999
(http://ooa.unh.edu/) to develop new technologies for growing seafood in New England.
The site was located 12 km offshore, in 50 m water depth, away from commercial
fishing, recreational boating and navigational routes. To escape surface energies (waves)
experienced offshore, submersible cage and mooring systems were employed. Culture
methods for new marine fish species were investigated (cod, haddock and halibut) to
relieve fishing pressures on wild stocks. The project developed and demonstrated new
submersible cages (Chambers et al., 2011), mooring systems (DeCew et al., 2012),
mussel longline technologies (Langan et al., 2003) and remote feeding systems (Rice et
al., 2003). It also demonstrated that is was feasible to produce cold water, marine finfish
in submerged cages (Howell et al., 2005; Chambers et al, 2006,2007; Rillahan et al.,
2009,2011), and collect environmental data in real time from the offshore site (Irish et
al., 2004,2001). Although the project succeeded in generating significant amounts of
data and new information, the high costs, exposed nature of the site, and slow growth of
the fish species cultured, created operational and economic challenges.
Based upon the experiences and lessons learned from the offshore project, an
alternative aquaculture model was designed that would emphasize small-scale production
closer to shore. These smaller systems would be more affordable and user friendly for
fishermen. However, concerns were made by the EPA regarding near shore aquaculture
81
in an already nitrogen impaired Piscataqua River. To address EPA’s concern of N
loading, we decided to us an integrated multi-trophic aquaculture (IMTA) farming
system. IMTA is where the culture of a fed product (i.e. fish) is combined with the
culture of organic and nonorganic extractive species that bio-mitigate nutrients from the
farm and surrounding waters. This creates product diversification, improves farm output,
helps maintain a clean environment and is more socially acceptable. Integrated
aquaculture is a biologically and technically feasible method to reduce the environmental
impacts of by-products from fish culture. The concept of developing an "environmentally
clean" aquaculture, based on the integrated culture of fish, mollusks and macro-algae,
was first proposed by Gordin et al. in 1981. The system was subsequently tested (Gordin,
1982; Gordin et al., 1990; Shpigel et al., 1991) and further developed (McDonald, 1987)
with shrimp and oysters in land-based facilities (Wang, 1990; Wang et al., 1990; Qian et
al., 1999).
Fish farming releases nutrients to the environment causing hyper-nitrification
(Gowen and Bradbury, 1987). The negative impact of aquaculture derives mainly from
particulate and dissolved nutrients from animal excretion and uneaten food (Krom and
Neori, 1989). IMTA promotes economic and environmental sustainability by converting
byproducts and uneaten feed from fed organisms into harvestable crops, thereby reducing
eutrophication, and increasing economic diversification (Neori et al., 2004; Troell et al.,
2003; Toumay, 2006). More recently, IMTA has been investigated extensively in
Atlantic Canada with salmon, blue mussels and kelp (Neori et al., 2004; Ridler et al.,
2006, 2007; Robinson, et al., 2007). However, uptake efficiency in open-water IMTA is
still unknown (Reid et al, 2007).
82
To encourage NH fishermen on small scale IMTA, extension programs were
developed through the Saltonstall Kennedy program and NH Sea Grant. These programs
enabled local fishermen to participate in and learn small-scale integrated aquaculture of
steelhead trout, blue mussel and sugar kelp grown. With this experience, fishermen can
determine if IMTA will be a suitable business alternative to fishing full time.
Method and Materials
Permitting
As part of the state permitting process, an application is filed with NH Fish and
Game (NHFG) for a preliminary evaluation. Following this, NHFG forwards the
application to the Army Corps of Engineers, NH Port Authority, NH Department of
Environmental Services, NH Health and Human Resources, the US Coast Guard and
National Marine Fisheries Service for their review and comments. After this, a public
hearing was set and letters of intent (Certified) must be sent to the abutters nearest the
aquaculture site. Written comments are accepted up to two weeks after the public
hearing. A onetime application fee to NHFG is $200 per requested site. If granted, an
annual permit and production fee is assessed at $750 / acre / year for suspended culture,
and $0.45 / kg for product sold.
If the application is accepted and passes public scrutiny, permits are then granted
by the following agencies: 1.) NH Fish & Game (Aquaculture Li); 2.) NH Port Authority
(Mooring Permit); 3.) Army Corps of Engineers (for anchor placement on the bottom);
and 4.) US Coast Guard (Aids to Navigation and lighting on structures).
83
Before the application can be submitted, an environmental survey had to be conducted at
each requested site. Environmental information was gathered on the bottom depth,
substrate content, tidal current direction and speed. In addition, NHFG sends divers down
to each intended site to inspect and verify habitat structure and resident biota. Other
information gathered for the state permitting process included the following:
1. Site coordinates (GPS)
2. Water quality (dissolved oxygen, pH, temperature and salinity)
3. Proximity to historical sites
4. Critical habitat for marine organisms
5. Proximity to commercial traffic
6. Potential user conflict by fishermen and recreational boaters
7. Product to be raised
8. Culture system
9. Planned annual production (biomass)
To sample the bottom of each site, a Van Veen sampler was used to collect
sediment. These samples were photographed and placed in to 3.75 1 plastic bags with
labels for analysis on shore. Water quality was derived with a hand held Y SI5 to obtain
information on DO, temperature, and salinity and a “Red Sea” test kit was used to sample
ammonia, nitrite and nitrate.
Eight NH fishermen gathered the necessary data required for permitting and six
applications were filled for permit in the Piscataqua River, NH. A public hearing was
held for the sites on May 24th 2010. At the public hearing, site descriptions and
84
operational methods were described for small scale trout farming. Although the public
hearing was generally positive, the EPA stepped in and expressed concerns about the
addition of nitrogen input trout farming to the already nitrogen impaired Piscataqua
River. This halted the aquaculture permitting process until a nitrogen mitigation plan
could be developed.
In response to the EPA’s concerns, we gathered biological data and
mathematically modeled nitrogen uptake of blue mussels and sugar kelp that could be
cultured alongside the steelhead trout. As a result, the EPA approved a demonstration
project that would involve integrated multi-trophic aquaculture (IMTA) to bio extract
nutrients from the river.
NH Fish & Game Department then issued a commercial aquaculture license for
the IMTA demonstration project. The site was located near shore in New Castle, NH.
Here, the bottom substrate consisted of sand and cobble, the water depth was 8.2 m at
MLW, and the current speed could flow up to 0.50 m / sec. An environmental monitoring
program, consisting of water column chemistry, benthic sampling, and video transects,
was established to assess any impacts to the Piscataqua River.
Integrated Multi-trophic Aquaculture
Culture Technology
Two high density polyethylene (HDPE) cages were moored between two 750 kg
Jeyco anchors (Fig. 4.1. A). Each anchor line was 30 m long, made from 5 cm dia.
Polysteel line and shackled to an upper bridle on the fish cage. Each of the two cages
85
1
measured 4.5 x 4.5 m, had a net depth of 3.5 m, and a volume of 68 m . The combined
float platform had a radar reflector and solar light per U.S. Coast Guard requirements.
Steelhead trout
Steelhead trout juveniles (Oncorhynchus my kiss) were purchased from Sumner
Brook Fish Farm in Ossipee, NH. Sumner Brook sourced the eggs from Trout Lodge in
Sumner, Washington. The diploid (all female) juveniles (-150 g mean weight) were
transported in insulated 1 m3 containers supplied with oxygen to the Jackson Estuarine
Laboratory on Great Bay, NH where they were acclimated from freshwater to brackish
water (20 ppt.). After 2 weeks in this land based, flow through system, the trout were then
moved to full strength ocean water (30-32 ppt.) at the Judd Gregg Marine Research Pier
(JGP) in New Castle, NH. There, they were placed into sea cages under the pier and
acclimated to their new marine environment.
Blue mussels
The fish cage platform was used to capture and grow blue mussels (Mytilus
edulis) on suspended lines (Fig 4.1.B). Galvanized eye bolts were screwed into the
perimeter of the wooden walkways at 0.7 m intervals. From these, New Zealand fuzzy
rope was suspended to collect mussel spat. Each line was 4 m long and had a 2.0 kg sash
weight tied to the end to keep it vertical during strong tidal currents (0.35 m / sec.). The
fuzzy rope was made from loops of polyester line providing abundant surface area for
mussel settlement. Mussels typically spawn twice per year in early and late summer in
the Gulf of Maine and adhere to bottom substrate and materials in the water column
(Langan et al. 2003).
86
Sugar kelp
Sugar kelp (Laminaria saccharina) is endemic to New England waters and
naturally settles on subsurface substrate. The HDPE cage platforms provided essential
habitat for kelp settlement (Fig. 4.2). In the late fall of 2012, sorus tissue (gametophyte)
was collected from mature kelp and spawned in captivity. With the help of Ocean
Approved in Portland, ME (http://www.oceanapproved.com/) and ME Sea Grant, kelp
spores were successfully spawned onto twine that was seeded for ocean growout on
empty fish cages at the JGP.
Technology Transfer to NH Fishermen
A priority of the project was to involve commercial fishermen in the
demonstration project, thereby giving them both experience and training on the
techniques for small scale aquaculture. Recruitment and selection of fishermen was
accomplished in an initial meeting with the New Hampshire Commercial Fishermen’s
Association. In this initial meeting, set up with the assistance of UNH and NH Sea
Grant, we explained the past and current projects, talked about cage options, the steps
involved in aquaculture, went over the costs of fish, feed, and cages, and did a simple
economic projection. As a result, 8 commercial fishermen expressed serious interest in
working together to grow seafood for local markets. Following this, a series of informal
meetings were held that focused on: 1) reinforcement and deployment of fish cage
frames; 2) net antifoul treatment and deployment; 3) trout transfer and acclimation to
seawater; 4) feed acquisition, management and distribution; 5) net and platform
maintenance; and 6) trout harvest and transfer to markets.
87
Environmental Monitoring
As mandated by the EPA, NH fish & Game and the NH Department of
Environmental Services, an environmental monitoring (EM) program was established for
the demonstration project. The EM program was designed, vetted through the EPA and
carried out by UNH staff. The program included the following:
1. Water samples were collected using a one-liter Niskin bottle. Samples were
taken 2 m below surface at three different locations: 1) inside the cage; 2) 15 m up
current; and 3) 15 m down current from the cage. Sampling occurred in May before the
fish were transferred to the sea cages, in August at midterm of the growout, and again in
December after the final harvest. A “Red Sea” test kit was used to measure ammonia,
nitrite and nitrate. Other environmental data collected included dissolved oxygen, pH,
salinity, and current speed and direction.
2. Sediment samples were collected by SCUBA divers at the same locations and
dates noted above. They were collected with a 5.0 cm diameter by 10 cm long PVC pipe
with cap. Each sample (~ 600 ml) was placed into a labeled zip lock bag and frozen for
later analysis.
3. Divers were also used to gather under water video of the substrate in the
vicinity of the cage. Video was taken 1 m off the bottom along a 30 m transect (NE-SW
direction) line extending 15 m up current and 15 m down current of the cage site. This
was used to detect any changes in the benthic community, or deposition of fish food that
could lead to anoxic spots. Video samples were collected on the same dates as above and
archived on a DVD for the regulatory agencies.
88
Summary reports of the findings, as well as the video, were submitted to New
Hampshire Fish & Game and the EPA after each sampling.
Market Survey of Steelhead Trout
A market survey form was developed to gather information about the fish from
wholesalers, retailers, restaurants and consumers. The survey asked questions pertaining
to meat quality, color, smell, texture and taste. Price point and amount of fish taken per
week were also included (Table 4.1). Restaurants and wholesalers were contacted to
ascertain their interest in receiving the product and answering the survey form. Orders
were taken prior to the first harvest in the fall of 2012. Entities that received fresh trout,
and provided feedback for the survey, were the following:
1. Black Trumpet (Portsmouth, NH)
2. Brown Trading Company (Portland, ME)
3. Common Man Restaurant (Portsmouth, NH)
4. Gonic Smokehouse (Rochester, NH)
5. Jumping Jays Fish Cafe (Portsmouth, NH)
6. Portsmouth fishermen’s community (Portsmouth, NH)
7. Restaurant 106 (Portsmouth, NH)
8. River House (Portsmouth, NH)
9. Sanders Fish Market (Portsmouth, NH)
10. Seaport Fish (Portsmouth, NH)
11. Thai House Two (Lee, NH)
12. UNH dining facilities (Durham, NH)
89
Results
Demonstration of Integrated Multi-trophlc Aquaculture
Although the fishermen were most interested in raising steelhead trout, the EPA’s
concern over added nitrogen mandated that IMTA be part of the demonstration project.
Our conceptualized IMTA plan, which included trout, mussels and sugar kelp, was
approved for one site in the Piscataqua River. Informal meetings throughout the growout
cycle helped inform the fishermen on the culture techniques for the added species, and all
three species were successfully grown.
Steelhead trout
Steelhead trout were relocated from Sumner Brook Trout farms to the JGP on
May 15, 2011 (n=200) and again on June 30, 2011 (n=800). They were used in a study to
investigate their tolerances to withstand periods of submergence (Chapter 3, funded by
Saltonstall Kennedy). After the research, 311 trout (mean length of 37.36 ± 2.6 cm, and
mean weight of 775.5 ± 246 g) were donated to the fishermen who wished to try raising
them. The group gathered each week to conduct cage and net maintenance, and they took
turns hand feeding once / day with a 6 mm, Bio Trout fish pellet (45% protein, 22%
lipid). In November 2012, harvesting commenced and continued once / week until mid-
December (Fig. 4. 3). At harvest, fish were netted from the sea cages, placed into a
saltwater ice bath, bled, gutted, rinsed, and packed on ice in 25 kg totes before delivery to
the markets. At final harvest, the fish had a mean length of 41.1 ± 0.63 cm and mean
weight of 1127.7 ± 96.4 g. The feed conversion ratio was 1.24, specific growth rates were
90
0.32 % / day and survival was 98 %. Total harvest weight for the season was 415.61 kg.
The fishermen sold the trout to two local seafood retail markets for $13.20 / kg.
After harvest, the nets were removed and cleaned, and the frames were towed into
the JGP area for winter storage. The demonstration site was left to fallow for 5 months
until the next growout cycle in the spring of 2013.
Blue mussels
Wild mussel spat naturally settled on the fish net and on fuzzy rope suspended
around the cage platform (Fig. 4.4). Mussel spat that settled on the fish net was cleaned
off by hand and later sorted into 4 m long mesh sleeves (‘socks’) at the JGP. They were
then hung from a growout raft under the JGP for continued nutrient extraction.
On November 15, 2012, the mussels were sampled and had a mean length of 9.8 ±
3.4 mm, a mean weight of 0.10 ± 0.045 g, and a density of ~ 75,456 / m of dropper line.
In total, the 52,4 m dropper lines had a combined weight of 1153 kg. A mussel sub
sample (tissue and shell) was sent to the New Jersey Feed Labs in Trenton, NJ for
proximate analysis. Results from the analyses indicated a nitrogen content of 1.4% for the
mussel tissue and 0.68% for the shell weight totaling ~ 2% for the entire mussel. These
results were similar to those of Rice (1999), who found that the N content of mussel
tissue ranged from 1.3-1.6 %. By multiplying the total weight of mussels (1153 kg) by
the nitrogen content of the mussel (2% by weight), we estimated the total nitrogen
extracted and sequestered by the mussels at this point in time to be 23 kg. The mussels
were left to grow, and continue extracting N from the Piscataqua River, until the fall of
2013.
91
The JGP area is prohibited to shellfish harvest due to its proximity to the
Portsmouth sewage treatment facility located 2.4 km up river (National Shellfish
Sanitation Program, 2011). Seawater and mussels samples were taken from the JGP and
trout demonstration site by the NH Department of Environmental Services in the spring,
summer and fall of 2013. Results indicated that bacteria levels were below FDA/EPA
standards for shellfish harvest. Despite this information, NH regulations states that
shellfish grown in prohibited waters must be relayed for at least six months in open
waters. To facilitate mussel relay, the entrepreneurial fishermen modified lobster pots
(1.2 x 0.5 x 0.30 m) to hold and store mussels on the bottom at an open, offshore site. In
August 2013, 10 preliminary pots were stocked with 50 kg of mussels and set near the
trout cage site in 10 m depth. They were checked monthly for 3 months to observe
survival, siltation and movement of the mussels within the pot. The mussels survived
well although some of the pots, particularly in soft sediment, had silt in the bottom which
made it difficult to pull them up and purge.
Based upon these preliminary results, another 25 traps were modified and filled
with ~ 2050 kg of mussels that were taken to Gunboat Shoals, NH, and set in 20 m water
depth for the winter (Fig. 4.5). This time the pots had deeper runners (5.0 cm) to help
keep the mussels off bottom and create better water flow for oxygenation and feeding.
The pots will be retrieved in the spring of 2014, cleaned, graded and taken to market. In
addition to the lobster pots placed offshore, 1250 kg of mussels were set overboard onto
the bottom to create a small mussel reef. The GPS location was recorded, and divers will
visit the site in the summer of 2014 to monitor growth, survival and predation.
Sugar kelp
92
Mature kelp blades (15), filled with gametophytes, were collected in November
2012 and brought to Ocean Approved for spawning. Sorus tissue was cut from the center
of the kelp blades into 15x10 cm strips, cleaned of any epiphytes with a soft cloth, and
refrigerated for 24 hrs. The next day, the spore strips were placed into two, 500 ml
beakers of seawater at a temperature of 11 ° C. The water temperature was allowed to
increase to 15.5 °C at which point the gametophytes released spores into the beaker
forming a tan color in the water. Each beaker was then poured into a 75 1 glass aquaria
filled with seawater. Inside the aquaria were 8 spools of twine for spore settlement. Each
spool was made of 5 cm dia. PVC pipe that was 30 cm long. Nylon twine (0.5 mm dia.)
was wrapped around the pipe to provide a soft substrate. After kelp settlement, fresh sea
water was cycled through the tanks once per week for six weeks. The spools, each with
100 m of twine (6000 spores / m), were delivered to UNH JGP in January of 2013. Here,
the seeded twine was wrapped around a heavier gauge (1.25 cm) polyester line (3.0 m
long), and suspended horizontally in cage frames (Fig. 4.6), or vertically suspended from
the floating docks at the pier.
Sugar kelp was grown throughout the winter and spring of 2013 (Fig. 4. 7).
Winter growth (January to early April) averaged 7.7 cm per day and had a mean length of
0.85 m by mid-April. As water temperatures increased from April to June (7-12°C), kelp
growth accelerated to 35.22 cm / day, averaged 2.5 m in length and had a mean weight of
3.5 kg / m by mid-June. Samples of fresh kelp were taken weekly from May 15 through
June 25 to the Black Trumpet restaurant in Portsmouth, NH. Here the kelp was
experimented with to create new recipes and to consider market viability. Customer
feedback was very positive and orders began to increase. Unfortunately by July, water
93
temperatures increased to 16 °C and epiphytes (Bryozoan sp.) began to cover the kelp
blades degrading their quality. The project demonstrated that kelp can be successfully
grown, however it is a seasonal product (fall-spring) for fresh markets. Kelp could be
better utilized by harvesting and processing (blanching and freezing or drying) in the
spring to increase shelf life and expand marketability.
Fate of nitrogen
The fish raised in 2012 were fed a total of 515.35 kg of Bio Oregon trout diet. The
approximate fate of the nitrogen, based upon food fed to the trout, is shown in Figure 4.8.
About 5% of the N was lost to the environment through uneaten feed, about 40% of the
nitrogen consumed by the fish was retained in their tissue (Hardy, 2012), about 50% was
excreted through the gills, and about 10% was lost in their feces.
With this model, total nitrogen input to the river from fish feed was 37.1 kg. This
was derived by taking the amount of protein in Bio Oregon diet (45%) and multiplying
this by the N content of the protein of the feed (16%). This gives you an N value of 7.2 %
N. This value was then multiplied by the total amount of feed fed (515.35 kg) to arrive at
37.1 kg of N.
It was estimated that the trout retained 40% of the nitrogen they consumed, less
5% lost to the environment (Hardy, 2012). At harvest ~ 14.0 kg of N was removed from
the ecosystem (Table 4.2). This was derived by the following calculation:
Total N - ((Total N fed x 95%) x 40%))
94
Ultimately, nitrogen was removed from the Piscataqua River by culturing mussels
and kelp. These organisms absorb nitrogen by organic and inorganic means. By October
2013, 3072 kg of mussels had been produced. With an N content of 2%, the total N
sequestered in the shell and tissue was 61.44 kg. Sugar kelp has a N content of 2.4 %
(Chopin, 2011). At a total weight of ~ 638 kg, 15.31 kg of this was N. Combined
together, mussel and kelp extracted 76.75 kg (61.44 kg + 15.31 kg) of N from the river
(Table 4.2).
These results were significant in that they proved that more N could be taken from
the river system then N put in from trout farming. The EPA and NH Fish & Game were
impressed with the demonstration and so have allowed the fishermen to triple trout
production in 2013.
Technology Transfer to NH Fishermen
Extension efforts engaged eight commercial fishermen on small scale aqua
farming in the Piscataqua River. Initial meetings were held in 2011 to outline culture
technologies, site selection, fish husbandry and economics. The fishers calculated their
potential expenses (vessel time, fuel costs, labor), as well as the potential income, to
assess the economics of the proposed project. Interest was high, and 6 fishermen came
forward to apply for commercial aquaculture permits in 2011 (see permitting section 2.2).
Results of the permitting process steered growout efforts toward an IMTA
approach. With this, the fishermen were trained “hands on” with IMTA and helped gather
nutrient uptake data for the permitting agencies. The training process started with a visit
to Sumner Brook Trout Farms. There, the fishers learned how the fish were grown, culled
95
and harvested for live transport. During the visit, trout fingerlings were sorted and
sampled for their transfer to the sea cages in the spring of 2012. Prior to fish transfer, the
fishermen were guided on cage reinforcement, mooring attachment, net deployment and
live transport systems. The trout were initially used in experiments by UNH researchers
until September 2012 (section 2.2). Afterwards, the fishermen took responsibility of the
cage systems and fish growout. During this period, the fishermen were taught feed
management protocol, how to identify and remove external parasites (sea lice) from the
trout. Also, they learned about size grading, as well as different ways to remove fouling
organisms from the nets (Fig. 4.9).
The fishermen took weekly turns feeding the fish. This activity was usually
conducted at the end of the day as they came back from their fishing grounds. Once a
week, the fishers would gather for a work party to exchange nets, conduct maintenance
on the cages, cull fish, or harvest (See http://nhsustainablefisheries.blogspot.com/).
Fishermen were taught the basics of mussel spat collection and growout. They
cut, added sash weights and deployed spat lines around the cage platform. They later
helped with relocating the spat lines to a raft under the JGP for the winter. To overcome
obstacles with inshore water quality (Section 3.13), the fishermen pooled their resources
and modified 35 lobster pots into small holding containers for mussel depuration. These
were later taken to Gun Boat Shoals to relay for six months.
NH kelp farming is still in its infancy. Additional growout trials will continue in
2013-2014. This product, once set on growout lines, can be raised rapidly throughout the
96
winter months and early spring. Markets are still developing for fresh kelp, and prices
will dictate whether or not interest will continue for this marine seaweed.
The fishermen brought inherent knowledge to the project that was gained from
working many years on the ocean. They quickly learned and adapted the new skill sets
they were taught for aquaculture. In the end, they were able to sell the trout for $13.20 /
kg (Fig. 4.10) and have over 3000 kg of mussels in relay for sale in 2014.
Environmental Monitoring
Water quality
Environmental and water quality data were collected on three different dates
throughout the trout growout in 2012-13 (Table 4.3 and 4.4). Water temperatures
decreased from 17.5°C in July to 5.3°C by January. Current speeds during this time
ranged from slack to 0.35m / sec and the direction was NE-SW. The pH of the seawater
differed slightly from 7.6 to 8.0. Dissolved oxygen levels were the lowest in September
(87.96 % saturation) and highest in January (103.5 % saturation). Water samples
collected for nitrogen analysis indicated no differences in ammonia, nitrite or nitrate
levels between the sample locations (Table 4.4).
Benthic and video sampling
The bottom samples consisted of sand (60 %), with some silt (20 %) and
fragmented shell and rocks (20 %). Larger rocks, scattered throughout the area, were
covered with encrusting colonies of sponges and seaweeds. Numerous lobster and crabs
inhabited the areas along the entire 30 m transect at each sample period.
97
No visual differences appeared along the 30 m transect throughout the IMAT
growout. Also, no fish food or anoxic areas were seen in the study site. The captured
video files were recorded onto a DVD and mailed to the EPA and NH Fish & Game for
their review. The video files were also archived, and benthic samples were frozen for
future analysis, if warranted (Fig. 4.11).
Market survey of steelhead trout
The steelhead trout were marketed between 2010 and 2012. Results of the market
survey were positive, with particular interest in a product that was raised locally.
Reported weekly demands ranged from 15-25 kg / restaurant, at they were willing to pay
-$15 / kg. Whole gutted fish at > 1.5 kg were acceptable, but larger fillets were preferred.
Surveyors commented on their mild taste that differed from farm-raised salmon. On a
scale of 1 (excellent) - 5 (poor), freshness, smell, texture and taste all rated number 1.
Steelhead Trout Economics for NH Fishermen
Simple economic spreadsheets for steelhead trout production, at three different
production scales, are given in Tables 4.5,4.6 and 4.7. Each table estimates the expenses
and income over a 3 year period, and assumes a stocking density of 20 kg / m3 at harvest.
Since fishermen already own and operate their vessels, no labor, boat payment or boat
insurance was included. Survival from stocking to harvest was estimated at 85%, feed
conversation ratio at 1.2, and yield (gutted weight to whole weight) at 75%. Price for
each 450 g fingerling ($5.00) from Sumner Brook Trout farms was based on prices we
have paid in the past. Selling price for harvested product at 2.5 kg round weight (1.87 kg
gutted weight) is given as $14 / kg, which was been the price paid in 2013. Feed cost
98
($2993 / mt) has been steady for the last two years. An additional charge of $0.50 / kg
was estimated for processing and distribution.
Profit improves as cage size increases from 100 to 1000 m3 (largest scale of
production). This is due to similar operational expenses to feed and maintain a single
large cage. Increased cage volume allows for more production per unit of effort. As cage
size increases, however, so does the amount of nitrogen added to the environment. For
this reason, larger cage(s) would likely be sited in deeper waters (>15 m) that have
moderate current flow (> to 0.20 m / sec) to help dissipate the added nutrients. Thus,
although there are greater economic rewards at a larger scale (>1000 m3), moving the
cage further offshore could increase the costs and risks of fanning. If profits increase
with scale, as we predict, and if larger scale systems have to move offshore, it is likely
that farmers will partner in a cooperative venture to share in the capital investment, and
spread the risk. They may also consider crop insurance that is now becoming available
through the FDA.
Results from these simple spreadsheets indicate that raising steelhead trout could
be profitable for commercial fishermen, particularly if done on a larger scale. There are
two primary reasons for this. First are cost savings for the fishermen. These individuals
already have vessels, vessel insurance, and other infrastructure, associated with their
primary business of fishing. All of these represent a considerable saving should they
initiate fish farming. Second, steelhead trout are relatively fast growing, have a good
food conversion ratio, and command a relatively high market price, which reduces
production costs and maximizes income.
99
It is likely that state and federal regulatory agencies will insist that steelhead trout
culture, particularly in coastal areas, be accompanied by shellfish and /or seaweed culture
to mitigate the addition of nutrients to the environment. Although these secondary crops
would add additional expenses to the operation (e.g. labor), these costs would be
recovered by their sale and could improve income gains to the farm.
Discussion
Results from the IMTA of steelhead trout, blue mussels and sugar kelp proved
successful in extracting more nitrogen from the Piscataqua River than was added from
trout production (Table 4.2). This is important as Reid (2007) reported uptake efficiency
from IMTA in open water is essentially unknown. What we do know is that mussel and
kelp recycle nutrients derived from fish waste (ammonia and phosphorus). Inorganic
nutrients are extracted directly by the kelp from the environment (Chopin, 2006; Neori et
al., 2004) while organic nutrients released by the fish are consumed by the mussels
(Lander et al., 2004; Troell et al., 2003; Mazzola and Sara, 2001). We were able to
culture three species in situ and quantify N input and uptake that resulted in ecosystem
benefits from aquaculture. Not only were the extractive organisms healthy for the
environment, they produced additional economic value to the farmer.
During the IMTA demonstration, NH fishermen were able to train “hands on”
with the basic skills to culture all three species. Additional training will be necessary to
improve current aquaculture methods for the steelhead. This includes developing a
custom vaccine for bath immersion, using new antifoul paint products to reduce bio-
fouling and working with a semi-moist feed formulation that will aid trout acclimate to
100
seawater. Also important will be the development of larger scale, robust, flexible
platforms that can safely maintain and grow multiple species together.
Blue mussels and sugar kelp can be grown in concert with the trout. However, the
mussels could not be sold due to the water classification of the cage site. This is due to
the proximity of a waste water treatment plant 2.8 km up river. This classification may
change in 2014 based upon water and shellfish samples collected by NH Department of
Environmental Services. Their data indicated the water quality was safe for shellfish
harvest at the cage site. If EPA re-classifies the head waters of the Piscataqua River, this
would greatly improve the logistics and economics for shellfish production.
Environmental monitoring indicated no negative effects to the bottom or to the
water column from farming on a small scale. This information has been given to the
regulatory agencies, and we are optimistic that this will help guide future permitting, and
allow the expansion of ocean farming.
Results of this EMTA project, although still preliminary, could be used in other
New England coastal areas. In particular, the fishing communities of the northeast where
fishery management initiatives have limited wild harvests. An important part of the
fishing industries strategy for maintaining their heritage and livelihood is to find
alternative ways to complement and diversify their operations. Aquaculture plays an
important role in maintaining an active water front and fishing heritage. Specific benefits
include alternative and economically viable uses for underutilized fishing vessels,
employment opportunities for displaced fishermen, business and marketing opportunities
101
for suppliers, restaurants, wholesale and retail outlets, and the benefit of locally produced,
high quality seafood for local, regional and national consumers.
The market survey suggested that steelhead trout is highly regarded, and that a
fresh, locally raised product is more preferable than a foreign import. Market capacity is
still unknown.
The fishermen are eager to increase aquaculture production in NH. Initial farming
sites that were applied for in 2011 are now being revisited for IMTA culture in 2014.
However, it is likely that inshore siting will be limited. Ultimately, if fishermen choose to
expand cage farming, they will have to consider moving offshore to deeper, more
exposed locations. Open ocean aquaculture will increase capital investment, daily
operational costs, and risk from oceanic storms. To overcome these obstacles, the
fishermen could form a cooperative to share investment, risk, and rewards. If they choose
to move offshore, UNH and NH Sea Grant will be on standby to assist them with the
expansion of marine aquaculture in New England.
102
Table 4.1. Consumer survey form that accompanied the steelhead trout delivered to seafood markets and restaurants in New England.____________________________
1. Approximate Yield (weight of filets / weight of whole fish):_____________
2. Product: Scale of 1 (excellent) to 5 (poor). Please enter a number.
Freshness (appearance of gills, eyes, skin)_________
Smell (fresh to old)___________
Texture (firm to soft)____________
Taste (excellent to poor)____________
Additional comments on product:
3. What is the optimal size/form of this product? Please check one or more.
Whole gutted (1-2 lbs.)_________
Whole gutted (2-4 lbs.)_________
Whole gutted (>4 lbs.)_________
Filets_________
Steaks_________
4. Comparison of this product to salmon:
________Same
________Different
________If different, describe difference.
5. Approximate price paid for similar product(s) ($/lb.) ___________________
6. What would be your demand (lbs.) daily/weekly/monthly)_______________
7. Is ‘produced locally’ important in marketing?
_______Very important
_______Somewhat important
_______Not at all important
8. General Comments (from wholesaler and consumers):- Overall impression:
- Suggestions for improvements:
103
Table 4.2.Nitrogen inputs and outputs from integrated multi-trophic aquaculture
Nitrogen input from feed
Total N Total N retained Date inout (kg) in trout (kg)Dec. 2012 37.10 14.0
Total N loss to environment 23.1 kg
Nitrogen extraction bv mussels (weight/m = 25.6 kg)
Total weight Total N Date Total line (m) (kg) Oct. 2013 120 3072
extracted (@ 2.0%) 61.44 kg
Nitrogen extraction bv sugar kelp (weigh t /m = 11.6 kg)
Total weight Date Total line (m) (kg)June 2013 55 638
Total Nextracted (@ 2.4%) 15.31 kg
Total N input from trout production Total N extraction from mussels and kelp
23.1kg 76.75 kg
Net N extracted from the river 53.65 kg
104
Table 4.3. Water quality data collected on 7/26/2012, 9/29/2012 and 1/9/2013 during the demonstration project.
Date Temp Current Current DO Salinity
(°C) Direction (°) Speed f°) dH (%) (pot)
7/26 16.3 220 0.18 7.97 101.4 29
9/26 17.5 45 0.35 7.6 87.96 30.8
1/9 5.3 35 0.1 8.0 103.5 30.1
105
Table 4.4. Water sampling for nitrogen content was conducted on 7/26/2012,9/29/2012 and 1/9/2013 from three locations; 1) inside the cage, 2) 15 m up current and 3) 15 m down current of the fish cages._______________________________________________
Date 7/26/2012
Water TestDown current of cage Inside case
Up current of cage
NH3 0-0.25 0-0.25 0-0.25
N02 0 0 0
NQ3 0.05-0.1 0.05-0.1 0.05-0.1
Date 9/26/2012
Water TestDown current of cage Inside cage
Up current of cage
NH3 0-0.25 0-0.25 0-0.25
N02 0 0 0
N03 0.05-0.1 0.05-0.1 0.05-0.1
Date 1/9/2013
Water TestDown current of cage Inside cage
Up current of cage
NH3 0-0.25 0-0.25 0-0.25
N02 0 0 0
NQ3 0.05-0.1 0.05-0.1 0.05-0.1
106
Table 4.5 Economic spreadsheet (3 yr.) for steelhead trout production in a 100 m3 cage at 20 kg / m3
Expenses Process &Cost / Total Cost Cage/Nets/ Handling
Year Item Number1 fingerllng of flngerllngs
1 Fingerlings 900 5 45002 Fingerlings 900 5 45003 Fingerlings 900 5 4500
IncomeMean total Total round
No. alive wgt. at wgt. At Crop value at Year at harvest4 harvest (kg) harvest (kg) harvest (kg)5
1 765 2.5 1912.5 206172 765 2.5 1912.5 206173 765 2.5 1912.5 20617
Total: $ 61,850
Feed cost2 Mooring Boat fuel3 $0.50/kg Total costs
6,866 10,000 3,000 956 25322.256,866 0 3,000 956 15322.256,866 0 3,000 956 15322.25
Total: $ 55,967
Profit/Loss over 3 years
Costs = $ 55,967Income = f 61,850Gain = $ 5,883
Notes: All expense and income amounts are in US dollars.1 Number stocked is designed to achieve a harvest stocking density of (20 kg/m3).2 Feed costs are based on an estimated FCR of 1.2, and is calculated based on the weight that survive to harvest.3 Boat fuel is estmated at $3.75/gal; 4 gallons/d over 100 days.4 Number alive at harvest is based on 85% survival.5 Crop value at harvest is based on 77% gutted, heads on weight, valued at $14/kg.
Table 4.6 Economic spreadsheet (3 yr.) for steelhead trout production in a 500 m3 cage at 20 kg / m3
Expenses
Year Item Number1Cost/
fingeriingTotal Cost
of fingeriings Feed cost2Cage/Nets/
Mooring Boat fuel3
Process &Handling$0.50/kg Total costs
1 Fingeriings 4500 5 22500 34,334 21,000 3,000 4,781 85615.252 Fingerlings 4500 5 22500 34,334 0 3,000 4,781 64615.253 Fingeriings 4500 5 22500 34,334 0 3,000 4,781 64615.25
Total: $ 214,846Income
Mean total Total roundNo. alive wgt. at wgt. At Crop value
Year at harvest4 harvest (kg) harvest (kg) harvest (kg)sProfit/Loss over 3 years
1 3825 2.5 9562.5 1030842 3825 2.5 9562.5 103084 Costs = $ 214,8463 3825 2.5 9562.5 103084 Income = $ 309,251
Gain = $ 94,405Total: $ 309,251
Notes: All expense and income amounts are in US dollars.1 Number stocked is designed to achieve a harvest stocking density of (20 kg/m3).2 Feed costs are based on an estimated FCR of 1.2, and is calculated based on the weight that survive to harvest.3 Boat fuel is estmated at $3.75/gal; 4 gallons/d over 100 days.4 Number alive at harvest is based on 85% survival.5 Crop value at harvest is based on 77% gutted, heads on weight, valued at $14/kg.
Table 4.7 Economic spreadsheet (3 yr.) for steelhead trout production in a 1000 m3 cage at 20 kg / m3______
ExpensesProcess &
Year Item Number1Cost/
fingerlingTotal Cost
of fingeriings Feed cost2Cage/Nets/ Handling
Mooring Boat fuel3 $0.50/kg Total costs1 Fingeriings2 Fingeriings3 Fingeriings
IncomeNo. alive
Year at harvest4
900090009000
Mean total wgt. at
harvest (kg)
555
Total round wgt. At
harvest (kg)
450004500045000
Crop value harvest (kg)s
68,66668,66668,666
30,000 3,000 9,563 0 3,000 9,563 0 3,000 9,563
Total:
156228.5126228.5126228.5
$ 408,686
Profit/Loss over 3 years1 7650 2.5 19125 206168oVO 2 7650 2.5 19125 206168 Costs s $ 408,6863 7650 2.5 19125 206168 Income = $ 618,503
Gain = $ 209,817Total: $ 618,503
Notes: All expense and income amounts are in US dollars.1 Number stocked is designed to achieve a harvest stocking density of (20 kg/m3)2 Feed costs are based on an estimated FCR of 1.2, and is calculated based on the weight that survive to harvest.3 Boat fuel is estmated at $3.75/gal; 4 gallons/d over 100 days4 Number alive at harvest is based on 85% survival5 Crop value at harvest is based on 77% gutted, heads on weight, valued at $14/kg.
Figure 4.1. A. Two trout cages moored at the mouth of the Piscataqua River, NH used in the integrated multi-trophic aquaculture project. B. Diagram of a fish cage and net with the New Zealand fuzzy rope suspended from the perimeter of the wooden walkway.
Figure 4.2. Natural settlement of sugar kelp on the trout cages in the Piscataqua River, NH.
I l l
Figure 4.3. Fishermen harvesting steelhead trout for local markets in Portsmouth, NH.
112
Figure 4.4. A. Juvenile mussel spat that settled on the New Zealand fuzzy rope suspended around the cage platform. B. Mussel spat that attached onto the nylon mesh fish nets.
Figure 4.5. A. Mussels being set into modified lobster pots for relaying offshore near Gunboat Shoals NH. B. The F/V Beatrice A relocating the mussel pots offshore. They will be harvested and sold in the spring of 2014.
Figure 4.6. A. Spools of juvenile sugar kelp line that was wrapped around 3.0 m polyester lines and submerged 0.5 m below surface in floating fish cage frames for growout (B).
115
u
i AFigure 4.7. Sugar kelp after 4 months growout in the Piscataqua River, NH. Kelp averaged 0.7 m length in April 2013.
116
Nitrogen Input of Feed(45% protein, 22% lipid)
Excretion 50%
Retention 40% (Hardy, 2012)
Figure 4.8. The fate of nitrogen from fish food to the environment.
117
Figure 4.9. A. NH fishermen towing empty cages to site for growout of steelhead trout, mussels and sugar kelp in the Piscataqua River. B. Fishermen gathered around a cage to discuss fish health and feeding.
118
Figure 4.10. A. Harvest of steelhead trout from the sea cages with the Portsmouth fishermen. B. Trout fillets on ice at Sanders Fish Market in Portsmouth, NH for $ 14.99/lb.
119
Figure 4.11. A. Diver with a Go ProTM underwater camera filming a 30 m bottom transect under the sea cages in the Piscataqua River, NH. B. Diver preparing to take a sediment sample with a PVC pipe sampler (5 cm x 10 cm) at the end of the transect.
DISSERTATION SYNOPSIS
This dissertation research had three goals, all of which related to fostering marine
aquaculture in New England. The first (Chapter 1) investigated an alternative cage
material potentially useful in reducing or eliminating bio-fouling, which is a major
problem in cage culture wherever it is practiced. The second was to experimentally
investigate the responses of caged steelhead trout (Onchorhynchus my kiss) to different
culture environments. In Chapter 2, we examined the fishes’ response to high currents,
and associated net deformation, that would be typical of many coastal areas of New
England. In another section (Chapter 3), we gathered preliminary data on the ability of
steelhead to survive and grow in submerged cages, which may be necessary if the
industry grows and expands offshore. In the final chapter (4), we report on the final goals
of the research, which were to provide hands-on aquaculture training to commercial
fishermen, and to evaluate the efficacy of Integrated Multi-trophic Aquaculture (IMTA)
to mitigate the addition of nutrients by the finfish growing operations.
Results of the research reported in Chapter 1 showed that fish cages built from a
copper alloy mesh (Seawire™) had less bio-fouling compared to traditional, nylon mesh
nets, which became heavily fouled with the hydroid Tubularia sp. Further, cod held in
the Seawire and nylon mesh cages for extended periods of time displayed similar feed
conversion ratio, specific growth rates, condition factor and survival. Importantly, Cu
levels were similar in the tissues of cod (gill and liver) held in the two cage types,
indicating that there was no additional Cu ion absorption from the Seawire net material.
121
In addition to reducing bio-fouling, alloy netting such as Seawire also has greater
tensile strength than nylon, and thus is better at retaining fish in the cage, and keeping
predators out. This is especially important in areas with large populations of seals like
New England. Although Seawire has some positive attributes, it is more expensive than
nylon mesh, more difficult to build into cage shapes, and much heavier to deploy and
handle in the field. This initial higher cost, and other negative attributes, may be offset by
less need for net cleaning and mending. As well, Cu alloy nets can be recycled, so the
user can recoup some of the purchase price when the nets are retired.
In Chapter 2 we determined that a biotelemetry system could be used to
simultaneously monitor the shape of a fish cage, and the fish within it. At current speeds
of > 0.2 m / s, we detected some net deformation, and at current velocities of 0.5 m / s,
the net lost > 30% of its volume. During high tidal currents (>_0.35 m / s) trout exhibited
rheotaxis, and the group used a smaller percentage of the cage volume. During slack tides
the fish exhibited typical circular, schooling behavior that utilized more space in the cage.
No differences were found in trout swimming speed, or depth occupied, between night
and day. The small cage size (63 m3) we used may have affected trout behavior, which
makes it difficult to compare our results to other similar studies, or to extend these results
to larger commercial size cages. We believe, however, that understanding fish behavior
in cages is a worthwhile goal since behavior ultimately affects fish welfare and
production. Additional research is certainly warranted, and we are confident that the
techniques we developed will be useful to those who follow.
The three trout submergence studies reported in Chapter 3 had varied results.
Cage size (3.73 - 68 m3), cage material (Seawire™ vs. nylon nets) and fish size (300 -
122
1000 g) all contributed to the variation. Despite the variation, the data indicated that
steelhead trout can be submerged for days to weeks with no significant negative effects
on growth or survival. We believe, however, that surface cage systems are preferred
since fish in surface cages have access to the surface to refill their swim bladders. As a
management tool, however, submerging the cages for short periods of time (days to
weeks) to escape adverse surface situations conditions (e.g. storms, high water
temperature, ice, red tide) will be useful, and can now be done more confidently. Future
submergence research should be conducted at deeper depths (> 10 m) because increased
pressure may well have an effect on the behavior and physiology of forcibly submerged
fish.
The final chapter of the dissertation reports on our efforts to involve and train
several NH commercial fishermen on the techniques of small-scale aquaculture, and to
demonstrate and quantify integrated multi-trophic aquaculture as a means of nitrogen
mitigation. The IMTA model demonstrated that N extraction by shellfish and seaweed
exceeded the nitrogen input from trout production. The model was verified through
environmental monitoring, which indicated no measurable environmental effects from
fish production. The information gathered was reported to the EPA and NH Fish &
Game, and we are hopeful it will be useful as they consider future aquaculture permit
applications. The training program provided participating fishers with a new skill set that
they could adopt either part or full-time, to help offset economic hardships caused by
federal management measures that have decreased catch allocations. Seafood markets
were very interested in all three marine species raised during the project. The trout were
sold (gutted, heads on) for $13.20 / kg. The mussels have not yet been sold, but we
123
expect, based on the sale of other cultured mussels, to sell for > $4.00/kg. The sugar kelp
was test marketed at a local restaurant in Portsmouth, NH. Their estimated demand was
10-20 kg / week at a price of $20 / kg.
In summary, we believe we have achieved our overall goals. We have tested an
alternative cage material, and we have conducted experiments on steelhead trout that
have increased our understanding of their behavior and physiology when grown in strong
currents or in submerged cages. We have also provided hands-on aquaculture training to
commercial fishermen, and evaluated the efficacy of IMTA to mitigate the addition of
nutrients associated with finfish production. Finally, we have made an attempt to
evaluate the economics of steelhead aquaculture, at three different scales, which should
be useful as potential growers make early and fundamental decisions in their business
plans.
124
Appendix
A. UNH IACUC Approval 2013
University of New Hampshire
Research Integrity Services, Service Building 51 College Road, Durham, NH 03824-3585
Fax; 603-862-356427-Sep-2013
Chambers, Michael D School of Marine Science - EWOS 24 Cokwos Road Durham, NH 03824
IACUC # : 130803Project: Sea Grant Extension 2013-2016 Category: CApproval Date: 22-Aug-2013
The Institutional Animal Care and Use Committee (IACUC) reviewed and approved the protocol submitted for this study under Category C on Page 5 of the Application for Review of Vertebrate Animal Use in Research or Instruction • the research potentially involves minor short-term pain, discomfort or distress which will be treated with appropriate anesthetics/analgesics or other assessments.
Approval Is granted for a period of three years from the approval date above Continued approval throughout the three year period is contingent upon completion of annual reports on the use of animals. At the end of the three year approval period you may submit a new application and request for extension to continue this project Requests for extension must be filed prior to the expiration of the original approval.
Please Note:1. Ail cage, pen, or other animal identification records must indude your IACUC # listed above.2. Use of animals in research and instruction is approved contingent upon participation in the
UNH Occupational Health Program for persons handling animals. Participation is mandatory for aH principal investigators and their affiliated personnel, employees of the University and students alike. Information about the program, including forms, is available at http;//unh.edu/research/occupational-health-Droqram-anlmal-handlers.
If you have any questions, please contact me at 862-4629 or Julie Simpson at 862-2003.
IACUC,
Vice Chair
cc FileHowell, William
125
B. UNH IACUC Approval 2010
University of New Hampshire
Research Integrity Services, Office of Sponsored Research Service Building, 51 College Road, Durham, NH 03824-3585
Fax:603-862-3564
08-Mar-2010
Chambers, Michael Atlantic Marine Aquaculture Center Chase Ocean Engineering Lab Durham, NH 03824
IACUC#; 100204 Category: DProject: SINTEF Bilateral Escape- Use of Biotelemetry to Quantify Fish in Net Pat Movement
Simultaneously
The Institutional Animal Care and Use Committee (IACUC) has reviewed and recommended approval of the protocol submitted for this study contingent upon your response to the following:
1. As the study was proposed as a pilot study (Section 27, C), IACUC approval is limited to one yeaijstudy completion dats should be revised accordingly).2. In Section n, B (personnel information), the IACUC anticipated personnel other than those listed handling fish (e.g., graduate students or other project staff) In the study. Anyone handling animats on the study needs to be Inducted on the application.3. The researcher needs to explain why steelhead trout are being used in the study instead of Atlantic salmon.4. In Section IV, A (experimental design), the researcher needs to address the following:
a. Describe the process for acdhnadng /fefr to saltwater from freshwater, including where the process will take place, the duration, and pertinent Information, such as tank size, water temperature, densities, and feeding schedule.b. Estimate mortality during the acdimadon process (see 4a). c Indude information on the total duration of the expenment.d. Provide details of the process for transporting fish from the source to the pen, and for stacking the pen.
5. In Section V, C (evaluation of outcomes), the IACUC did not consider vocalization as an appropriate outcome for this study so removed this attribute.6. In Section VI, A (method to determine animal numbers), the researcher needs to provide the method for determining the number of animals proposed to have pingers inserted (eight). (The justification for the total number in the pen is adequate.)7. As this pen is a new animal facility, Dr. Dean Bder must inspect the pen and approve the standard operating procedure before any animals are transported to the site.8. The researcher stated that fish will be saved for future use a t the end o f the study. If the pen is to be removed from the ocean, the researcher needs to explain what will happen to the fish (i.e., where the fish will be housed and the details of transportation and stacking). This explanation should specifically Identify what will happen to the fish with pingers inserted.
126
9. In Section 7 of the Surgical Procedures Form (surgical procedures), the researcher needs to add Information about surgical site preparation (I.e., stte deaned with cNorhexkffne solution), aeration of the cooler, and the length of time for recovery after F&-222administration.
As soon as the IACUC receives an appropriate response to its concerns, above, it wffl Issue you an approval letter for this protocol. You may not commence activities in this protocol involving vertebrate animals until you frave received IACUC approval. Please respond to the IACUC within sixty days of this letter. If the IACUC does not receive a response within sixty days, your protocol will be withdrawn.
If you have any questions, please contact either Dean Elder at 862-4629 or Julie Simpson at 862- 2003.
For the IACUC,
A. Bolker, Ph.D.Chair
cc: File
127
C. NH Aquaculture Permit
H EAD Q U AR TER S: 11 H a re n Ofive, C on cord , N H 0 3 3 0 1 -6 5 0 0 (6 0 3 ) 2 71-3421 FAX (6 0 3 ) 2 7 1 -1 4 3 8
New HampshireFish and Game Department
irww.WMdNH.come-mari in to O w tk fU e n h g o v
TDD A c c e s s R e la y NH 1 -8 0 0 -7 3 5 -2 9 6 4
J u ly 1 7 .2 0 1 2
Michael Chambers/Hunt Howell UNH. Jere Chase Ocean Engineering Lab 24 Colovos Road Durham, New Hampshire 03(24
MARIHE AQVACVIiTVRE LICENSE 2812-13
In compliance with Part Fis (07 Rules on Aquaculture, the New Hampshire Fish A Came Department has reviewed and approved an application submitted by Michael Chambers aad Huat Howell, for cage culture of steelhead trout (Oncorhynchus m yiia) and blue mussel (Ktytlhu tdulls).
Conditions of the license include:
1. Steelhead juveniles may be provided by Summer Brook Trout Farm in Ossipee, N.H. The fish must be diploid and all female. Prior to movement Don the Ossipee hatchery to the coastal fish cages, health certificates must be reviewed by New Hampshire Fish A Game. Up to 600 may be stocked into the cages in 2012.Blue mussel will be gathered from the wild, caught on lines m coastal New Hampshire waters aad will be suspended around the perimeter of the cage platform.
2. The cage and surrounding cage platform will be moored in a New Hampshire Port Authority approved location using a double mooring block/anchor system. The dimensions of the surface cage shall not exceed 2S' x 30' and have a surrounding walkway of IS* width. The location lies off Newcastle beach at Lat43.04.365/Long 70.42.3>0. The water depth at this site is about 25 It MW. The cage must not be closer than 10' from the bottom on any tide. The area covered by this license is a 1/10 acre pkx.
3. Trout from the Ossipee, Summer Brook Trout Farm will be stocked into the cage at about 150g end be grown to 2-3kg. Hwvest and processing of the fish will be on site or seaward of the site such that no resulting waste remains are washed ashore. Continuing deployment of the cage system will require renewal of the annually issued Marine Aquaculture License.
4. The blue mussels caught there and elsewhere at the she may not be put to maeket as the location is not approved by NHDES for shellfish harvest. Mussels may be disposed of on dry land at a site approved by New Hampshire Fish A Game or at sea m water deeper than 75', beyond the line that demarcates the outer boundary ofthe nitrogen impaired estuary. Disposal either dry land or at sea, must be supervised and attended by New Hampshire Fish A Came. Should the licensee seek to market these blue mussels, an acceptable plan for relocating them to an area approved by NHDES for harvest and culturing them in the new location for a sufficient amount of time must be developed by the stale agencies (NHF A G. NHDES, and NHDHHS). The plan, which will include provisions for state personnel observation of the relocation operations and appropriate labeling and documentation of relocated product will become a required condition of this license.
(60S) 788-31*4 FAX (* 0 0 )7 8 * 4 8 2 3
•mail: reg l •w M H e.nh.gov
829B Hem S eeet Lancaster, NH 03684-3*12
REGIO N 1
(603) 744*5470 FAX (803) 744-8302
email: i e g 2 < wS0He.nh.gov
N ew Hampton. NH 0325*
REGION 2 PO Bo* 417
Durham, NH 03824-4732(8 0 3 )8 8 8 -1 0 9 6
FAX (803) 868-3306
8EGJQH3 2 2 5 Main Street
R E G IO N *15 A sh Brook Court K eene. NH 03431
< 003)362-9880 FAX (803) 362-879*
emaS: reg30 iisatei.nh.gov em ail reg4«w *dSte.nh.|
128
NH Fish and Game Cont.
5. Environmental monitoring at tbe cage site shall consist of biannual video inspections by underwater camera ofthe tea floor at key locations at and around the cage. In addition, water quality testing on a bimonthly frequency is required.Further detail of the required environmental monitoring is in the attached Environmental Monitoring Program
6. Any observed disease problems shall be reported immediately to the Executive Director and the Chief of Marine Fisheries Division of the New Hampshire Fish & Game Department, followed by a letter outlining die circumstances and providing as much dkail as possible.
7. Any control methods for eradication or removal of project fouling organisms, predators, or diseases other than by hand and pumped water shall be discussed with the Chief of Marine Fisheries, New Hampshire Fish ft Game Department Written approval of control methods must be obtained from the Executive Director prior to implementation.
8. The permittee shall notify the Executive Director and the Chief of Marine Fisheries within 48 hours of any unusual event as defined in Fis 807.08.
9. Aquaculture operations shall not interfere with or cause damage to recreational and/or commercial activities in and around the licensed she including, but not limited to, lobster traps, moorings, navigational aids, and piers.
10. Annual reports of disposal of aquaculture products shall be made in accordance with Fis 807.10.
11. A copy of records relevant to harvesting (i.e. dates, quantity harvested, etc.) and disposition of aquaculture product shall be retained by the permittee for a period of one year (or until turned over to New Hampshire Fish ft Game Department). Such records shall be subject to inspection at any time by fee Executive Director or his agent.
12. This license is valid upon the applicants receiving all necessary federal or state permits.
13. The permittee shall prepare and submit to New Hampshire Health and Human Services a Hazard Analysis Critical Control Point Plan (HACCP) thirty (30) days prior to the marketing of shellfish.A copy of this shall be sent to fee New Hampshire Fife ft Game Department
This license shall expire on December 31,2012, unless sooner revoked or rescinded. The annual report required by Fis 807.10 must be submitted by January 31 of 2013.
GN/BWS/vjb
Enclosure
cc: Doug Grout, Chief Marine FisheriesLt. Jeffrey A. Marston Law Enforcement Sandy Falicon, Rules Coordinator
129
LIST OF REFERENCES
Aarsnes, J.V., L0land, G. and Rudi, H., 1990. Current forces on cage, net deflection. In: Engineering for Offshore Aquaculture. Thomas Telford, Glasgow, pp. 137-152.
Ashley, P.J. 2007. Fish welfare: Current issues in aquaculture. Applied Animal Behavior Science. 104: 199-235.
Begout Anras, M.L. and Lagardere, J.P. 2004. Measuring cultured fish swimming behavior: first results on rainbow trout using acoustic telemetry in tanks. Aquaculture 240: 175-186.
Bjordal, A., Fosseidengen, J., Totland, B., Ovredal, J. Femo, A. and Huse, I. 1986.Monitoring biological and environmental parameters in aquaculture. Modeling, Identification and Control. 7: 209-18.
Benetti, D., O'Hanlon, B., Rivera, J., Welch, A., Maxey, C. and Orhun, M. 2010.Growth rates of cobia (Rachycentron canadum) cultured in open ocean submerged cages in the Caribbean. Aquaculture 302 (2010): 195-201.
Braithwaite, R.A. and McEvoy, L.A., 2005. Marine bio-fouling on fish farms and its remediation. Adv. Mar. Biol. 47: 215-252.
Braithwaite, R.A., Carrascosa, M.C.C. and McEvoy, L.A. 2007. Biofouling of salmon cage netting and the efficacy of a typical copper-based antifoulant. Aquaculture, Vol. 262 (No. 2-4): 219-226.
Broom, D. 1998. Fish welfare and the public perception of farmed fish. In: Nash, C., Julien, V. (Eds.), Report Aquavision ’98. The Second Nutreco Aquaculture Business Conference Stavanger Forum, vol. 1998, Norway, 13-15, 89-91.
Cardehlhac, P. and Whitaker, B., 1988. Copper treatments: uses and precautions, Vet Clin N Am (sSm Animal Prac) 18: 435-448.
Carl, C. 2008. Hydroid growth on aquaculture nets, Carl von Ossietzky University, Oldenburg, Diploma thesis.
[CAWMA] Comprehensive Assessment of Water Management in Agriculture.2007. Water for Food, Water for Life: A Comprehensive Assessment Of Water Management in Agriculture. Earthscan.
130
Chambers, M.D., Bunker, J., Watson, W. and Howell, W.H. 2012. Comparative growth and survival of juvenile Atlantic cod (Gadus morhua) cultured in copper and nylon net pens. J. Aquaculture Research and Development, 3:5. http://dx.doi.org/10.4172/2155-9546.1000137
Chambers, M.D., DeCew, J., Celikkol, B., Yigit, M. and Cremer, M.C. 2011. Small- Scale, Submersible Fish Cages Suitable for Developing Economies. Global Aquaculture Advocate 14 (1): 30-32.
Chambers, M.D., Langan, R., Howell, W., Celikkol, B., Watson, W., Bamaby, R.,DeCew, J. and Rillahan, C. 2007. Recent Developments at the University of New Hampshire Open Ocean Aquaculture Site. Bull. Aquacul. Assoc. Canada 105-3.
Chambers, M.D. and Howell, W. H. 2006. Preliminary information on cod and haddock production in submerged cages off the coast of New Hampshire, USA. ICES Journal of Marine Science 63 (2.): pages
Chambers, M.D. and Ostrowski, A.C., 1999. Development of bluefin trevally (Caranx melampygus) and greater amberjack (Seriola dumerili) for offshore aquaculture. In: Stickney, R.R. (Ed.), Joining Forces with Industry: Proceedings of the Third International Conference on Open Ocean Aquaculture, Corpus Christi, Texas (USA), May 10-15.
Chester, R. 1990. Marine Geochemistry. Unwin Hyman, London, 698 pp.
Chopin, T. 2011. Pers. comm. Professor of Marine Biology, University of New Brunswick, Department of Biology, Saint John, N.B., E2L 4L5, Canada.
Cohen, J. E. 1995. How many people can the earth support? W. W. Norton &Company, New York. 532 p.
Cubitt, K.F., Churchill, S., Rowsell, D., Scruton, D.A. and McKinley, R.S. 2005. 3-Dimensional positioning of salmon in commercial sea cages: assessment of a tool for monitoring behaviour. In: Spedicato, M.T., Lembo, G., Marmulla, G. (Eds.), Acoustic Telemetry: Advances and Applications, Proceedings of the 5th Conference on Fish Telemetry held in Europe. Ustica, Italy, 913 June, 2003, Rome, FAO/COISPA-FAO Rome, 25-33.
DeCew, J., Fredriksson, D.W., Lader, P., Chambers, M., Howell, H., Osienki, M., Celikkol, B., Frank, K. and Hpy, E., 2013. Field Measurements of Cage Deformation using Acoustic Sensors. Aquaculture Engineering. In Press.
DeCew, J., Celikkol, B., Baldwin, K., Chambers, M. D., Irish, J., Swift, M.R. and Tsukrov, I. 2012. The Design, Deployment, Utilization and Recovery of an Offshore Mooring System for Fin fish Aquaculture. The Magazine of the World Aquaculture Society. 43 (3): 32-36.
131
Dempster, T., Juell, J.-E., Fosseidengen, J.E., Fredheim, A. and Lader, P. 2008.Behaviour and growth of Atlantic salmon (Salmo salar L.) subjected to short-term submergence in commercial scale sea-cages. Aquaculture 276: 103-111.
Dempster, T., Kors0en, 0 ., Folkedal, O., Juell, J.E. and Oppedal, F. 2009. Submergence of Atlantic salmon (Salmo salar L.) in commercial scale sea-cages: a potential short-term solution to poor surface conditions. Aquaculture 288: 254-263.
de Nys, R. and Guenther, J. 2009. The impact and control of bio-fouling in marine finfish aquaculture. In: Advances in Marine Antifouling Coatings and Technologies. Woodhead Publishing, Cambridge, UK, pp. 177-221.
Diana, J.S. 2009. Aquaculture production and biodiversity conservation. BioScience 59: 27-38.
Dodson, J.J. and Mayfield, C.I. 1979. Modification of the rheotropic response of rainbow trout {Salmo gairdneri) by sublethal doses of the aquatic herbicides Diquat and Simazine. Environ. Pollut. 18: 147-157.
Drumm, A. 2010. Evaluation of the promotion of offshore aquaculture througha technology platform (OATP). Galway, Ireland, Marine Institute, pp. 46 (also available at www.offshoreaqua.com/docs/OATP_Final_Publishable_report.pdf).
FAO Fisheries and Aquaculture Department. 2012. The status of world fisheries and aquaculture 2012. Food and Agriculture Organization of the United Nations, Rome. 26.
FAO 2010. State of world fisheries and aquaculture. 2010. Electronic edition. http://www.fao.Org/docrep/013/i 1820e/i 1820e00.htm
Femo, A., Huse, I., Juell, J.-E. and Bjordal, A. 1995. Vertical distribution of Atlantic salmon (Salmo salar L.) in net pens: trade-off between surface light avoidance and food attraction. Aquaculture 132, 285-296.
Floen, S., Totland, B. and Ovedal, J. 1988. A PC-based echo integration system for fish behavior studies. Int. Counc. Explor. Sea C. M. B. 35.
Fpre, M., Dempster, T., Alfredsen, J.A., Johansen, V. and Johansson, D. 2009. Modeling of Atlantic salmon (Salmo salar L.) behavior in sea cages: A Lagrangian approach. Aquaculture 288: 196-204.
Fredheim, A. 2005. Current forces on net structures. Doctoral Thesis (Dr. Eng.), Department of Marine Technology, Norwegian University of Science and Technology, Norway.
132
Fredriksson, D. W., DeCew, J., Swift, M. R., Tsukrov, I., Chambers M. D. and Celikkol,B. 2004. “The Design and Analysis of a Four-Cage Grid Mooring for Open Ocean Aquaculture”. Aquacultural Engineering 32, 77-94.
Fredriksson, D.W., Palcynski, M.J., Swift, M.R. and Irish, J.D. 2003. Fluid dynamicdrag of a central spar fish cage. In: Bridger, C.J., Costa-Pierce, B.A. (Eds.), Open Ocean Aquaculture. From Research to Commercial Reality. The World Aquaculture Society, Baton Rouge, Louisiana, pp. 151-168.
Furevik, D.M., Bjordal, A., Huse, I. and Femo, A. 1993. Surface activity of Atlantic salmon (Salmo salar L.) in net pens. Aquaculture 110(2): 119-128.
FSBI (Fisheries Society of the British Isles). 2002. Fish Welfare. Briefing Report 2. Granta Information systems, http://www.le.ac.uk/bilogy/fsbi/welfare.pdf.
Greene, J.K. and Grizzle, R.E. 2007. Successional development of fouling communities on open ocean aquaculture fish cages in the western Gulf of Maine, USA. Aquaculture. 262, 289-301.
Gordin H, Motzkin F, Hughes-Games A. and Porter C. 1981. Seawater mariculture pond an integrated system. European Aquaculture Society Special Publication 6: 1-13.
Gordin, H., Krom, M. Neori, A., Porter, C. and Shpigel, M. 1990. Intensive integrated seawater fish ponds: Fish growth and water quality. EAS (European Aquaculture Society) Special Publication No. 11, pp. 45-65.
Gowen, R.J. and Bradbury, N.B. 1987. The ecological impact of salmon farming incoastal waters: A review. Oceanography Marine Biology Annuals Review, 25: 563-575
Gordin, H. 1982. Aquaculture: Potential development. In: Oceanography: Present and Future, Brewers, P.G. (ed.). Springer Verlag, New York, pp. 145-152.
Gordin, H., Motzkin, F., Huges-Games, W.L. and Porter, C. 1981. Seawater maricultura pond. An integrated system. European Mariculture Society Special Publication No. 6, pp. 1-13.
Hardy, R. 2012. Pers. comm. Professor and Director Aquaculture Research Institute. Animal & Veterinary Science, University of Idaho, 875 Perimeter Drive MS 2330, Moscow, ID 83844-2330.
Harris, L. G., 1986. Size -selective predation in a sea anemone, nudibranch and fish food chain. Veliger 29: 38-47.
133
Harris, L. G. and Irons, K.P. 1982. Substrate angle and predation as determinates in fouling community succession. In: Cairns, J. (Ed.), Artificial Substrates. Ann Arbor Science Pub., Ann Arbor Michigan, pp. 131-174.
Hennessey, T. and Healey, M. 2000. Ludwig’s Ratchet and the Collapse of New England Groundfish Stocks Coastal Management, 28:187-213.
Hevrpy, E.M., Boxaspen, K., Oppedal, F., Taranger, G.L. and Holm, J.C. 2003. The effect of artificial light treatment and depth on the infestation of the sea louse Lepeophtheirus salmonis on Atlantic salmon (Salmo salar) culture. Aquaculture 220: 1-14.
Hoagland, P., Jin, D., Thunberg, E. and Steinback, S. 2005. "Economic activityassociated with the Northeast Shelf Large Marine Ecosystem: application of an input-output approach". Chapter 7 in: Hennessey T.; Sutinen, J., eds. Sustaining large marine ecosystems: the human dimension. Amsterdam, The Netherlands: Elsevier; p. 159-181.
Hoyle, I., Oidtmann, B., Ellis, T., Turnbull, J., North, B., Nikolaidis J. and Knowles,T.G. 2007. A validated macroscopic key to assess fin damage in farmed rainbow trout (Oncorhynchus mykiss). Aquaculture 270(1-4): 142-148.
Howell, W.H. and Chambers, M.D. 2005. “Growth performance and survival of Atlantic halibut (Hippoglossus hippoglossus) grown in submerged net pens,” Bull. Aqua. Assoc. Canada, 9:35-37.
Huse, I. and Holm, J.C. 1993. Vertical distribution of Atlantic salmon (Salmo salar) as a function of illumination. J. Fish Biol. 43, 147-156.
Irish, J.D., Carroll, M., Singer, R., Newhall, A., Paul, W., Johnson, C., Witzell W. and Rice G. 2011. Instrumentation for Open Ocean Aquaculture Monitoring, WHOI Tech. Rept. 2001-15.
Irish, J.D., Fredriksson, D.W. and Boduch, S. 2004. Environmental Monitoring Buoy and Mooring with Telemetry, Sea Technology, 45(5), 14-19.
Irish, J.D., Carroll, M., Singer, R., Newhall, A., Paul, W., Johnson, C., Witzell, W. and Rice G. 2001. "Instrumentation for Open Ocean Aquaculture Monitoring," WHOI Tech. Rept. 2001-15, Oct, 2001.
Johansson, D., Ruohonen, K., Juell, J-E. and Oppedal, F. 2009. Swimming depth andthermal history of individual Atlantic salmon (Salmo salar L.) in production cages under different ambient temperature conditions. Aquaculture 290, 296-303.
Johansson, D., Ruohonen, K., Kiessling, A., Oppedal, F., Stiansen, J.E., Kelly, M. and Juell, J.E. 2006. Effect of environmental factors on swimming depth preferences
134
of Atlantic salmon (Salmo salar L.) and temporal and spatial variations in oxygen levels in sea cages at a fjord site. Aquaculture 254, 594-605.
Johansson, D., Juell, J.E., Oppedal, F., Stiansen, J.E. and Ruohonen, K. 2007. Theinfluence of the pycnocline and cage resistance on current flow, oxygen flux and swimming behaviour of Atlantic salmon (Salmo salar L.) in production cages. Aquaculture 265(1-4), 271-287.
Juell, J. E. and Westerberg, H. 1993. An ultrasonic telemetric system for automaticpositioning of individual fish used to track Atlantic salmon (Salmo salar L.) in sea cages. Aquaculture. Eng. 12, 1-18.
Juell, J .E. and Fosseidengen, J.E., 1995. Akustisk mengdemaling av oppdrettslaxs.Fisken og Havet 21, 33 (In Norwegian).
Juell, J. E. 1995. The behavior of Atlantic salmon in relation to efficient cage-rearing. Reviews in Fish Biology and Fisheries. 5, 320-335.
Juell, J. E., Oppedal, F., Boxaspen, K. and Taranger, G.L. 2003. Submerged lightincreases swimming depth and reduces fish density of Atlantic salmon Salmo salar L. in production cages. Aquaculture Research 34 (6), 469—477.
Juell, J. E. and Fosseidengen, J.E. 2004. Use of artificial light to control swimming depth and fish density of Atlantic salmon (Salmo salar) in production cages.Aquaculture 233, 269-282.
Kapetsky, J.M., Aguilar-Manjarrez, J. and Jenness, J. 2013. A global assessment of potential for offshore mariculture development from a spatial perspective.FAO Fisheries and Aquaculture Technical Paper No. 549. Rome, FAO. 181 pp.
Kils, U. 1988. Some aspects of schooling for aquaculture. Int. Counc. Explor. Sea C.M.F: 12.
Korspen 0., Dempster, T., Fjelldal P.G., Oppedal F. and Kristiansen, T. 2009. Long-term culture of Atlantic salmon (Salmo salar L.) in submerged cages during winter affects behavior, growth and condition. Aquaculture 296, 373-381.
Korspen 0 ., Dempster, T., Fjelldal P.G., Oppedal F. and Kristiansen, T. 2009. Long-term culture of Atlantic salmon (Salmo salar L.) in submerged cages during winter affects behavior, growth and condition. Aquaculture 296, 373-381.
Krom, M.D. and Neori A. 1989. A total nutrient budget for an experimental intensive fishpond with circularly moving seawater. Aquaculture 88: 345-358.
135
Lader, P., Dempster, T., Fredheim, A. and Jensen, 0 . 2008. Current induced netdeformations in full-scale cages for Atlantic salmon (Salmo salar). Aquae. Eng. 38, 52-65.
Lander T, Barrington K, Robinson S, MacDonald B and Martin J. 2004. Dynamics of the blue mussel as an extractive organism in an integrated multi-trophic aquaculture system. Bulletin of the Aquaculture Association of Canada. 104(3): 19-28.
Langan, R. and Horton, C.F. 2003. “Design, Operation and Economics of Submerged Longline Mussel Culture in the Open Ocean.” Bulletin of the Aquaculture Association of Canada, Vol. 103-3, 11-20.
Lie, O.K., Julshamn, K., Lied, E. and Lambertsen, G. 1989. Growth and feed conversion in cod (Gadus morhua) on different feeds, retention of some trace elements in the liver. Fisk. Dir. Skr., Ser. Emaering. 2: 235-244.
Lovely, E.C. 1995. Coexistence of hydroid predators and persistence of prey, Tubularia larynx and Tubularia indivisa (Hydrozoa: Tubulariidae), in shallow fouling communities. M.S. Thesis, University of New Hampshire.
Marra, J. 2005.When will we tame the oceans? Nature 436: 175-176.
Mazzola A and Sara G. 2001. The effect of fish farming organic waste on foodavailability for bivalve molluscs (Gaeta Gulf, Central Tyrrhenian, MED): stable carbon isotopic analysis. Aquaculture 192: 361-37.
McDonald, M.E. 1987. Biological removal of nutrients from wastewater: An algal-fish system model. In: Aquatic Plants for Water Treatment and Resource Recovery, Reddy, K.R. and Smith, W.H. (eds). Magnolia Publishing Inc, Orlando, pp. 959-968.
Magurran, A.E. 1993. Individual differences and alternative behaviors In Pitcher, T.J.., ed. The Behavior of Teleost Fishes, 2nd edn. London: Chapman and Hall. 78 - 441.
Moe, H., Dempster, T., Magne Sunde, L., Winther, U. and Fredheim, A. 2006.Technological solutions and operational measures to prevent escapes of Atlantic cod (Gadus morhua) from sea net pens. Aquaculture Research 38(1): 91 - 99.
Montgomery, J. C., Baker, C.F. and Carton, A.G. 1997. The lateral line can mediate rheotaxis in fish. Nature, Volume 389, Issue 6654, 960-963.
Myers RA, and Worm, B. 2003. Rapid worldwide depletion of predatory fish communities. Nature 423: 280-283.
136
National Shellfish Sanitation Program, Guide for the Control of Molluscan Shellfish,2011 Revision. 2011. U. S. Department of Health and Human Services Public Health Service Food and Drug and Drug Administration. Administrationhttp://www.fda.gov/Food/GuidanceRegulation/FederalStateFoodPr ograms/ucm2006754.htm?source=govdelivery.
Naylor, R. and Burke, M. 2005. Aquaculture and ocean resources: Raising tigers of the sea. Annual Review of Environment and Resources 30: 185-218.
Naylor, R., Hindar, K., Fleming, I.A., Goldburg, R., Williams, S., Volpe, J., Whoriskey, F., Eagle, J., Kelso, D. and Mangel, M. 2005. Fugitive salmon: assessing the risks of escaped fish from net pen aquaculture. BioScience 55(5): 427-437.
Neori, A., Chopin, T., Troell, M., Buschmann, A. H., Kraemer, G. P., Hailing, C.,Shpigel, M. and Yarish, C. 2004. Integrated aquaculture: rationale, evolution and state of the art emphasizing seaweed biofiltration in modem mariculture. Aquaculture 231: 361 -391.
New Hampshire Sea Grant Strategic Plan 2014-2017. 2013. New Hampshire Sea Grant Communications. Durham, NH. Pp 32.
Noga, E.J. 2000. Fish Disease, Diagnosis and Treatment. Iowa State University Press, Ames, Iowa. pp. 122-113.
Olla, B.L., Pearson, W.H. and Studholme, A.L. 1980. Applicability of behavioral measures in environmental stress assessment. Rapp. P.-V. Reun.-Cons. Int.Explor. Mer 179, 162-173.
Oppedal, F., Juell, J.E., Taranger, G.L. and Hansen, T. 2001. Artificial light and season affects vertical distribution and swimming behavior of post-smolt Atlantic salmon in sea cages. J. Fish. Biol. 58(6), 1570-1584.
Oppedal, F., Juell, J.E. and Johansson D. 2007. Thermo- and photo-regulatory swimming behavior of caged Atlantic salmon: Implications for photoperiod management and fish welfare. Aquaculture 265, 70-81.
Oppedal, F., Dempster, T. and Stien, L. 2011. Environmental drivers of Atlantic salmon behavior in sea-cages. Aquaculture 311, 1-18.
Osland, H., Sandvik, J.I., Holm, J., Heuch, P-A., and Bakke, S. 2001. Studie avlakseluspaslag og tilvekst hos Atlantisk laks (Salmo salar) i nedsenkede merder. HSF-report, R-NR 4/01, 22 p (In Norwegian).
137
Patursson, O. 2008. Flow Through and Around Fish Farming Nets. Ph.D. Dissertationsubmitted to the University of New Hampshire in partial fulfillment of the Ocean Engineering Degree program. University of New Hampshire, Durham, NH, 146p.
Pauly, D., Trites, A. W., Capuli, E. and Christensen, V. 1998. Diet composition andtrophic levels of marine mammals. ICES Journal of Marine Science 55: 467-481.
Pert, E. J. and Erman, D.C. 1994. Habitat use by adult rainbow trout under moderate artificial fluctuations in flow. Trans. Amer. Fish. Soc. 123: 913-923.
Pitcher, T. and Parrish, J. 1993. Functions of shoaling behavior in teleosts. In Pitcher, T.J.., ed. The Behavior of Teleost Fishes, 2nd ed. London: Chapman and Hall. 78 -441 .
Qian, P.Y., Wu, M. and Ni, I.H. 1999. Integrated Mariculture. III. SimultaneousCultivation of Seaweeds, Shellfishes and Fishes to Improve Seawater Quality and the Maximize Productivity. Proceedings of APEC Conference on Sustainability of Marine Environment: What Can the Private Sector Do? Kaouhsiumg, Chinese Taipei, 1-3 September 1999.
Rapp, P., Ramirez, W.R., Rivera, J.A., Carlo, M. and Luciano, R. 2007. Measurement of organic loading under an open ocean aquaculture cage, using sediment traps on the bottom. J. App Ichthyol. 23(6): 661-667.
Reid, G. K., Robinson, S., Chopin, T., Lander, T., MacDonald, B., Haya, K., Burridge,F., Page, F., Ridler, N., Justason, A., Sewuster, J., Powell, F. and Marvin, R.2007. An interdisciplinary approach to the development of integrated multi- trophic aquaculture (IMTA): bioenergetics as a means to quantify the effectiveness of IMTA systems and ecosystem response. World Aquaculture Society. Aquaculture 2007 conference proceedings, pg. 761.
Rice, G.A., Stommel, M., Chambers, M.D. and Eroshkin. O. 2003. “The Design,Construction, and Testing of the University of New Hampshire Feed Buoy,” Open Ocean Aquaculture, From Research to Commercial Reality. The World Aquaculture Society.
Rice, M.A. 1999. Control of eutrophication by bivalves: Filtration of particulates and removal of nitrogen through harvest of rapidly growing stocks. Journal of Shellfish Research 18(1): 275.
Ridler, N., Robinson, B., Chopin, T., Robinson, S. and Page, F. 2006. Development of integrated multi-trophic aquaculture in the Bay of Fundy, Canada: a socioeconomic case study. World Aquaculture 37(3): 43-48.
138
Ridler, N., Wowchuk, M., Robinson, B., Barrington, K., Chopin, T., Robinson, S., Page, F„ Reid, G. and Haya, K. 2007. Integrated multi-trophic aquaculture (IMTA): a potential strategic choice for farmers. Aquaculture Economics & Management 11: 99-110.
Rillahan, C., Chambers, M.D., Watson, W.H. and. Howell, W. H. 2009. “A self-contained system for observing and quantifying the behavior of Atlantic cod, Gadus morhua, in an offshore aquaculture cage,” J. Aquaculture.
Rillahan, C., Chambers, M. D., Howell, W. H. and Watson, W. H. 2011. The Behavior of Cod (Gadus Morhua) in an Offshore Aquaculture Net Pen. Aquaculture. Volume 310, Issues 3-4. Pp. 361-368.
Robinson, S., Lander, T., Martin, J.D., Bennett, A., Barrington, K., Reid, G.K., Blair, T., Chopin, T., MacDonald, B., Haya, K., Burridge, L., Page, F., Ridler, N., Justason, N., Sewuster, J., Powell, F. and Marvin, R. 2007. An interdisciplinary approach to the development of integrated multi-trophic aquaculture (IMTA): the organic extractive component. World Aquaculture Society. Aquaculture 2007 conference proceedings, pg.786.
Ryan, J., 2004. Farming the Deep Blue. Report to the Irish Sea Fisheries Board and the Irish Marine Institute, pp. 67.
Schreck, C.B., Olla, B.L. and Davis, M.W. 1997. Behavioral response to stress. In:Iwama, G., Pickering, A., Sumpter, J., Schreck, C. (Eds.), Fish Stress and Health in Aquaculture. Cambridge University Press, Cambridge. 145-170.
Sebens, K.P. 1986a. Community ecology of vertical walls in the Gulf of Maine, USA:small scale processes and alternative community states. In: Moore, P.G., Seed, R. (Eds.), The Ecology of Rocky Coasts. Columbia Univ. Press, New York, pp. 346- 371.
Sebens, K.P. 1986b. Spatial relationships among encrusting marine organisms in the New-England subtidal zone. Ecol. Monogr. 56 (1): 73-96.
Shpigel, M., Neori, A. and Gordin, H. 1991. Oyster and clam production in the outflow water of marine fish aquaculture ponds in Israel. EAS (European Aquaculture Society). Special Publication No. 14, p. 295
Smith, L.S. 1982. Introduction to Fish Physiology. T.F.H Publications, Hong Kong, UK. (352 pp).
Southgate, P. and Wall, T. 2001. Welfare of farmed fish at slaughter. In Practice 23, 277.
Swift, M.R., Fredriksson, D.W., Unrein, A., Fullerton, B., Patursson, O. and Baldwin, K. 2006. Drag force acting on bio-fouled net panels. Aquae. Eng. 35, 292-299.
139
Tamaru, C.S., Carlstrom-Trick, C. and Helsley, C.E. 1998. Aquaculture in Hawaii: Lessons from the Past, pp. 257-278. In: C.E. Helsley (ed.) Open Ocean Aquaculture’97 Charting the Future of Ocean Farming Proceedings of an International Conference, April 23-25 1997, Maui, Hawaii, University of Hawaii Sea Grant College Program, Honolulu, HI.
Thoney, DA., 1990. The Effects of Trichlorphon, Praziquantel, and Copper Sulfate onVarious Stages of the Monogenean. Benedeniella posterocolpa, a Skin Parasite of the Cownose Ray, Rhinoptera bonasus, Journal of Fish Disease. 13: 385-389.
Tookwinas, S. 1990. Laviculture of Seabass (Lates calcarifer) and grouper (Epinephelus malabaricus) in Thailand: advances in tropical aquaculture, Tahiti, February 20- March 4, 1989, Aquacop IFREMER Actes de Colloque 9: 645-659.
Troell, M., Hailing, C., Neori, A., Chopin, T., Buschmann, A.H., Kautsky, N. and YarishC. 2003. Integrated mariculture: asking the right questions. Aquaculture 226: 69- 90 Toumay B. 2006. IMTA: template for production? Fish Farming International, Vol. 33, No. 5, May 2006, pg. 27.
Tsukrov, I., Ozbay, M., Fredriksson, D.W., Swift, M.R., Baldwin, K. and Celikkol B. 2000. “Open Ocean Aquaculture Engineering: Numerical Modeling” Marine Technology Society Journal, Washington, D.C. Vol. 34, No. 1 pp. 29-40.
Van Duijn, C. Jr. 1973. Disease of Fishes, 3rd Edition, Springfield, 111., Published by Charles C. Thomas.
Wang, J.K. 1990. Managing shrimp pond water to reduce discharge problems. Aquaculture Eng., 9: 61-73
Wang, J.K., Lam, C.Y. and Jakob, G.S. 1990. Preliminary investigation of an oyster- shrimp joint production system. Trans. Am. Soc. Agric. Eng., 33(3): 975-980.
Ward, D., Fore, M., Howell, W.H. and Watson, W.H. III. 2012. The influence of stocking density on the swimming behavior of adult Atlantic cod, Gadus morhua, in a near shore net-pen. J. Amer. Aquaculture Soc. 43(5): 621-634.
140