Request for Quotation TRC Muncie Head Start Fan Coil Replacement and Additional Honeywell Controls

Transition Resources Corporation

12/10/2019

600 Corporation Drive, Suite 105 Pendleton, IN 46064

Due Date: January 10, 2020

Request for Quote

2

Submission Details

Submission Deadlines All submissions for responding to this request must be submitted on paper or electronically, as

stated below, no later than:

1/10/2019

4:30 PM ET

Submission Delivery Address

The delivery address to be used for submissions in person or mailed is:

Marla Monday

Transition Resources Corporation

600 Corporation Drive, Suite 105

Pendleton, IN 46064

The email address for electronic submissions is:

Marla Monday

Email: mmonday@transitionresources.org

Submission of Quote The Bid Form must accompany the proposal/quote (Attachment A).

If quote is mailed or hand delivered, please provide two (2) copies. Please use fonts no smaller

than 10 points.

Submission Questions and Clarifications Questions on any topics covered in this Request for Quote may be emailed to:

Gordon Upchurch

Email: gupchurch@transitionresources.org

Questions will only be accepted through email.

Introduction Transition Resources Corporation (TRC) is accepting quotes from qualified companies to

install 21 TRANE split system units over a period of 3 years. The units must be configured for

two 2017 Fulton 2 MBH Endura Boilers and will replace 1958 Herman Nelson fan coil units.

Eight (8) of the 21 units will require Honeywell Spyder Programmable Controllers to work with

a Honeywell WEB AX based automation system. An “open” license is required. For a detailed

installation timeline see Section - Specifications, Project Scope & Installation Timeline.

The project site is TRC Muncie Head Start Center located at 3900 E. Wysor Street, Muncie,

Indiana.

Request for Quote

3

Business Overview & Background

Telamon/TRC Corporation is a multi-state, multi-funded, private non-profit organization which

was organized in 1965 to provide assistance to those in need. In Indiana, Telamon Corporation

operates as Transition Resources Corporation.

Transition Resources Corporation (TRC) is a 501(c)(3) not-for-profit organization. TRC

operates Head Start and Early Head Start programs in Delaware and Madison counties serving

children birth through five years. TRC also provides the Jobs for America’s Graduates (JAG)

opportunity to high school students in Marion County and delivers a HUD-approved Housing

Counseling program in southern Indiana.

MISSION: To provide educational services that lead to better jobs, better lives, and better

communities.

Purpose, Specifications/Scope, Timeline & Budget

Purpose

Receive quotes for replacement of 1958 Herman Nelson fan coil units with TRANE split system

over a period of 3 years. Eight (8) of the 21 units will require Honeywell Spyder Programmable

Controllers to work with a Honeywell WEB AX based automation system. An “open” license is

required.

A separate contract agreement will be written for each of the three phases of the project.

Contract Agreements will be written as follows and based on the availability of funding:

Phase 1: January 17, 2020 – June 30, 2020

Phase 2: October 1, 2020 – June 30, 2021

Phase 3: October 1, 2021 – June 30, 2022

Specifications, Project Scope & Installation Timeline

The selected bidder will be responsible for the demo, labor, materials, site cleanliness and

equipment for the installation of twenty-one (21) TRANE split system units with 8 of the units

requiring Honeywell Spyder Programmable Controllers to work with a Honeywell WEB AX

based automation system.

Request for Quote

4

The timeline for installation is as follows:

The following criteria must be met to achieve a successful project:

Honeywell Spyder Programmable Controllers

• As outlined in the installation schedule, provide and install Honeywell Spyder

Programmable Controllers to work with a Honeywell WEB AX based automation

system with open license, expanded memory, enclosure, Lon card, Lon driver, and

embedded work bench software programming utility compatible with existing

Honeywell controls.

Controllers must communicate with installed Fulton Endura boilers and TRANE split

system fan coil units. Each unit will have an automation system controller, a power

transformer, a current sensor, a wall sensor, a discharge air sensor, a heating valve

electronic actuator, a carbon monoxide sensor, and an outdoor air damper actuator. All

programming and diagrams must be included.

Email alarming and trending should be standard and included.

For detailed specifications, see Attachment E.

• All controls will be warrantied for a period of five (5) years by manufacturer. The other

materials must be warranted for a minimum of one (1) year.

Request for Quote

5

• The platform must contain an “Open” license feature to be compatible with the existing

Honeywell system.

• Embedded workbench and the 256 MB memory feature should be included.

• A five (5) year remote monitoring software licensing agreement is preferred.

• Also required is an upgrade to TRC’s thirteen (13) existing Honeywell building

automation JACE to the latest N4 license software. This software is a maintenance build

and includes any all updates for a period of 5 years and includes:

Upgrade the JACE license to an N4 license, Migrate the existing AX station to an N4

station, Commission the JACE with the new N4 software modules, Copy the migrated

station back into the existing WEB-600 JACE, modify graphics to make compatible with

N4 modules, provide all needed graphic improvements, test access and operations,

follow up on a quarterly basis remotely only.

• End user training must be provided for staff (Hands On). Documented pre-service

training for maintenance staff.

TRANE Split-system Units

• Install twenty-one (21) TRANE split system fan coil units.

• New units will replace 21 Herman Nelson unit ventilators. Specs on the original existing

equipment:

Model #LWJDG4447-3, Volts 208, Single Phase, Amps 101, Frequency 60.

Patent Number: Dec 5, !950 2.532.550

Patent Number: Nov 15, 1955 2.723.616

Drawings (Attachment B) are included for a retrofit of our existing unit ventilators on

site showing measurements of overall width, depth, and height of the units.

• The selected contractor will provide all parts, equipment and labor to remove and replace twenty (21) units.

• It is the responsibility of the contractor to dispose of the fan coils that are removed.

• Contractor will provide any protection required to protect items such as floor,

computers and furniture.

• End user training must be provided for our staff (Hands On). Documented Pre-service

training for maintenance staff.

Project Timeline

Friday, December 19, 2019 10:00 a.m. ET

Pre-bid Meeting/Walk Through 3900 E. Wysor St., Muncie, IN

Friday, January 10, 2020

4:30 p.m. ET Proposals Due

January 13-15, 2020 Review Quotes

Friday, January 17, 2020 Issue Contract

March 20 – 29, 2020 Complete onsite work

Request for Quote

6

Notifications to bidders who were not selected will be completed by Thursday, January 16, 2020.

Budget

All proposals must include proposed costs to complete the tasks described in the project

scope. Costs should be detailed individually per scope of work or on a separate attachment.

Pricing should be listed on each job. In-kind contribution should be identified and itemized.

IN-KIND CONTRIBUTION

The Administration for Children and Families (ACF) requires all Head Start grantees such as Transition Resources Corporation to provide contributions equal to 25% of their total Federal

Head Start funding (or 20% of the total Federal and non-Federal combined). Transition

Resources Corporation is asking for an in-kind contribution from the Contractor selected that

might range from 10-25% of base bid.

In-kind is defined as property or services that benefit a grant supported project or program

(such as the Head Start Program) and are contributed by non-Federal third parties without

charge to the grantee. In-kind contributions may consist of the value of real property and

equipment and the value of goods and services directly benefiting the grant program and

specifically identifiable to it.

NOTE: All costs and fees must be clearly described in each proposal.

Bidder Qualifications

Bidders should provide the following items as part of their proposal for consideration:

• 3-5 references

• Staff and Qualifications

• Previous job work samples

Terms and Conditions

TRC reserves the right to reject all bids. Transition Resources Corporation is an equal

opportunity employer and service provider.

Evaluation Criteria

Transition Resources Corporation will evaluate all proposals based on the following criteria.

To ensure consideration for this Request for Proposal, your proposal should be complete and

include all the following criteria:

• Overall proposal suitability: proposed solution(s) must meet the scope and needs

included herein and be presented in a clear and organized manner

Request for Quote

7

• Organizational Experience: Bidders will be evaluated on their experience as it

pertains to the scope of this project

• Technical expertise and experience: Bidders must provide descriptions and

documentation of staff technical expertise and experience

• Value and cost: Bidders will be evaluated on the cost of their solution(s) based on

the work to be performed in accordance with the scope of this project

• Ability to Meet Required Timeline

• In-Kind contribution and/or cost saving measures

Scoring of Proposal:

o Overall Project Design & Proposed Solution – 15 pts

o Expertise and Experience – 20 pts

o Pricing –35 pts

o Ability to Meet Required Timelines – 15 pts

o In-kind contribution or cost saving measures - 15 pts

Attachments

Attachment A Bid Form

Attachment B Drawings

Attachment C Project Agreement Documents

Attachment D Prevailing Wage

Attachment E Honeywell WEBs

Attachment A

Bid Form (To be completed for all bids) (Please type or print)

RFQ Due Date: January 10, 2020, 4:30 p.m. EST

Bidder (Firm):

Address (Street):

City, State, Zip:

Phone:

Firm's Contact:

Phone Number:

Email Address:

IN-KIND IN KIND CONTRIBUTION for Head Start facility remodel project The Administration for Children and Families (ACF) requires all Head Start grantees such as TRC/Telamon Corporation to provide contributions equal to 25% of their total Federal Head Start funding (or 20% of the total Federal and non-Federal combined). TRC/Telamon Corporation is asking for an in-kind contribution from the Contractor that might range from 20% to 50% of Base Hourly Rate.

In-kind is defined as property or services that benefit a grant supported project or program (such as the Head Start Program) and are contributed by non-Federal third parties without charge to the grantee. In-kind contributions may consist of the value of real property and equipment and the value of goods and services directly benefiting the grant program and specifically identifiable to it.

Total Amount of In-Kind Proposed by Bidder:

$

Total Project Cost: $

Date Signature

Attachment B

TELAMON CORPORATION Transition Resources Corporation

Procurement Contract Provisions The following provisions, as applicable, are conditions and assurances agreed and certified to by the contractor upon acceptance of a contract to provide certain goods or services, and are made part thereof.

1. The contractor shall comply with Executive Order 11246, as amended by Executive Order 11375, “Amending Executive Order 1246 Relating to Equal Employment Opportunity,” and as supplemented by regulations at 41 CFR Part 60, “Office of Federal Contract Compliance Programs, Equal Employment Opportunity, Department of Labor.” 2. All contracts and subgrants in excess of $2000 for construction or repair of facilities awarded by recipients and subrecipients are subject to the Copeland “Anti-Kickback” Act, 18 U.S.C. 874, as supplemented by Department of Labor regulations, (29 CFR Part 3, “Contractors and Subcontractors on Public Building or Public Work Financed in Whole or in Part by Loans or Grants from the United States”). The Act provides that each contractor or subrecipient shall be prohibited from inducing, by any means, any person employed in the construction, completion or repair of public work, to give up any part of the compensation to which s/he is otherwise entitled. 3. When required by Federal program legislation, all construction contracts awarded by recipients and subrecipients of more than $2000 are subject to the Davis-Bacon Act, (40 U.S.C., 276a to a-7) and as supplemented by Dept of Labor regulations (29 CFR part 5, “Labor Standards Provisions Applicable to Contracts Governing Federally Financed and Assisted Construction”. Under this Act contractors are required to pay wages to laborer and mechanics at a rate not less than the minimum wages specified in the current wage determination made by the Secretary of Labor. In addition, contractors are required to pay wages not less than once a week. Copies of these provisions are attached and made part of this contract. Weekly payroll information recorded on Optional Form WH-347 or its equivalent (also attached) must be submitted to the local Telamon project official for inclusion with billing information. 4. Where applicable, all contracts awarded by recipients in excess of $2000 for construction contracts and in excess of $2500 for other contracts that involve the employment of laborers or mechanics are required to comply with sections 102 and 107 of the Contract Work Hours and Safety Standards Act, (40 U.S.C. 327-333) as supplemented by Department of Labor regulations (29 CFR part 5). Section 102 requires the contractor to compute the wages of every mechanic and laborer on the basis of a standard, work week of 40 hours. Work in excess of the standard work week is permissible provided that the payment of wages in excess of 40 hours at 1 ½ times the basic pay rate. Section 107 provides that no laborer or mechanic shall be required to work in surroundings or under working conditions that are unsanitary, hazardous or dangerous. 5. Any inventions resulting from experimental, developmental or research work shall be subject to 37 CFR part 401, “Rights to Inventions Made by Nonprofit Organizations and Small Business Firms Under Government Grants, Contracts and Cooperative Agreements.” 6. Recipients of contracts and subgrants in excess of $100,000 agree to comply with all applicable standards, orders or regulations issued pursuant to the Clean Air Act, (42 U.S.C., 7401 et seq.) and the Federal Water Pollution Control Act, as amended (33 U.S.C. 1251 et seq.). 7. Contractors who bid for an award of more than $100,000 must file, with Telamon, a certification of compliance with restrictions of the Byrd Anti-Lobbying Amendment, (31 U.S.C., 1352), that it has not and will not use federally appropriated funds to pay any person or organization for influencing or attempting to influence a member of Congress, officer or employee of Congress, or an employee of a member of Congress in connection with obtaining any federal contract, grant or other award covered by the amendment. Contractors shall also disclose any lobbying with non-Federal funds that takes place in connection with obtaining any Federal award. 8. Contractors shall certify that they are not prohibited from receiving procurement awards pursuant to Executive Orders 12549 and 12689, “Debarment and Suspension”, and do not appear on the General Services Administration’s “List of Parties Excluded from Federal Procurement or Nonprocurement Programs.” 9. Contractors shall provide a current Certificate of Insurance naming Telamon Corporation as an additional insured and which verifies general liability and Workers Compensation coverage. In West Virginia in lieu of a Workers Compensation certificate of insurance, a valid current Certificate of coverage from the WV Workers Compensation Commission is required.

CONTRACTOR: _______________________ DATE: _________________________ By: _______________________________ Title: _________________________

Copeland Act Contract Provisions (1) Purpose:

This part prescribes “anti-kickback” regulations under section 2 of the Act of June 13, 1934, as amended (40 U.S.C. 276c), popularly known as the Copeland Act. This part applies to any contract which is subject to Federal wage standards and which is for the construction, prosecution, completion, or repair of public buildings, public works or buildings or works financed in whole or in part by loans or grants from the United States. The part is intended to aid in the enforcement of the minimum wage provisions of the Davis-Bacon Act and the various statutes dealing with federally assisted construction that contain similar minimum wage provisions, including those provisions which are not subject to Reorganization Plan No. 14 (e.g., the College Housing Act of 1950, the Federal Water Pollution Control Act, and the Housing Act of 1959), and in the enforcement of the overtime provisions of the Contract Work Hours Standards Act whenever they are applicable to construction work. The part details the obligation of contractors and subcontractors relative to the weekly submission of statements regarding the wages paid on work covered thereby; sets forth the circumstances and procedures governing the making of payroll deductions from the wages of those employed on such work; and delineates the methods of payment permissible on such work.

(2) Weekly statement with respect to payment of wages.

(a) As used in this section, the term employee shall not apply to persons in classifications higher than that of laborer

or mechanic and those who are the immediate supervisors of such employees. (b) Each contractor or subcontractor engaged in the construction, prosecution, completion, or repair of any public

building or public work, or building or work financed in whole or in part by loans or grants from the United States, shall furnish each week a statement with respect to the wages paid each of its employees engaged on work covered by this part 3 and part 5 of this chapter during the preceding weekly payroll period. This statement shall be executed by the contractor or subcontractor or by an authorized officer or employee of the contractor or subcontractor who supervises the payment of wages, and shall be on form WH 348, “Statement of Compliance”, or on an identical form on the back of WH 347, “Payroll (For Contractors Optional Use)” or on any form with identical wording. Sample copies of WH 347 and WH 348 may be obtained from the Government contracting or sponsoring agency, and copies of these forms may be purchased at the Government Printing Office.

(c) The requirements of this section shall not apply to any contract of $2,000 or less. (d) Upon a written finding by the head of a Federal agency, the Secretary of Labor may provide reasonable

limitations, variations, tolerances, and exemptions from the requirements of this section subject to such conditions as the Secretary of Labor may specify.[29 FR 97, Jan. 4, 1964, as amended at 33 FR 10186, July 17, 1968; 47 FR 23679, May 28, 1982]

(3) Submission of weekly statements and the preservation and inspection of weekly payroll records.

(a) Each weekly statement required under Sec. 3.3 shall be delivered by the contractor or subcontractor, within seven days after the regular payment date of the payroll period, to a representative of a Federal or State agency in charge at the site of the building or work, or, if there is no representative of a Federal or State agency at the site of the building or work, the statement shall be mailed by the contractor or subcontractor, within such time, to a Federal or State agency contracting for or financing the building or work. After such examination and check as may be made, such statement, or a copy thereof, shall be kept available, or shall be transmitted together with a report of any violation, in accordance with applicable procedures prescribed by the United States Department of Labor.

Page 1 of 4 Attachment D

(b) Each contractor or subcontractor shall preserve his weekly payroll records for a period of three years from date of completion of the contract. The payroll records shall set out accurately and completely the name and address of each laborer and mechanic, his correct classification, rate of pay, daily and weekly number of hours worked, deductions made, and actual wages paid. Such payroll records shall be made available at all times for inspection by the contracting officer or his authorized representative, and by authorized representatives of the Department of Labor.

(Reporting and recordkeeping requirements in paragraph (b) have been approved by the Office of Management and Budget under control number 1215-0017)

(4) Payroll deductions permissible without application to or approval of the Secretary of Labor.

Deductions made under the circumstances or in the situations described in the paragraphs of this section may be made without application to and approval of the Secretary of Labor: (a) Any deduction made in compliance with the requirements of Federal, State, or local law, such as Federal or State

withholding income taxes and Federal social security taxes. (b) Any deduction of sums previously paid to the employee as a bona fide prepayment of wages when such

prepayment is made without discount or interest. A bona fide prepayment of wages is considered to have been made only when cash or its equivalent has been advanced to the person employed in such manner as to give him complete freedom of disposition of the advanced funds.

(c) Any deduction of amounts required by court process to be paid to another, unless the deduction is in favor of the contractor, subcontractor, or any affiliated person, or when collusion or collaboration exists.

(d) Any deduction constituting a contribution on behalf of the person employed to funds established by the employer or representatives of employees, or both, for the purpose of providing either from principal or income, or both, medical or hospital care, pensions or annuities on retirement, death benefits, compensation for injuries, illness, accidents, sickness, or disability, or for insurance to provide any of the foregoing, or unemployment benefits, vacation pay, savings accounts, or similar payments for the benefit of employees, their families and dependents: Provided, however, That the following standards are met: (1) The deduction is not otherwise prohibited by law; (2) It is either:

(i) Voluntarily consented to by the employee in writing and in advance of the period in which the work is to be done and such consent is not a condition either for the obtaining of or for the continuation of employment, or

(ii) Provided for in a bona fide collective bargaining agreement between the contractor or subcontractor and representatives of its employees;

(3) No profit or other benefit is otherwise obtained, directly or indirectly, by the contractor or subcontractor or any affiliated person in the form of commission, dividend, or otherwise; and

(4) The deductions shall serve the convenience and interest of the employee. (e) Any deduction contributing toward the purchase of United States Defense Stamps and Bonds when voluntarily

authorized by the employee. (f) Any deduction requested by the employee to enable him to repay loans to or to purchase shares in credit unions

organized and operated in accordance with Federal and State credit union statutes. (g) Any deduction voluntarily authorized by the employee for the making of contributions to governmental or quasi-

governmental agencies, such as the American Red Cross. (h) Any deduction voluntarily authorized by the employee for the making of contributions to Community Chests,

United Givers Funds, and similar charitable organizations. (i) Any deductions to pay regular union initiation fees and membership dues, not including fines or special

assessments: Provided, however, That a collective bargaining agreement between the contractor or subcontractor and representatives of its employees provides for such deductions and the deductions are not otherwise prohibited by law.

(j) Any deduction not more than for the “reasonable cost” of board, lodging, or other facilities meeting the requirements of section 3(m) of the Fair Labor Standards Act of 1938, as amended, and part 531 of this title. When such a deduction is made the additional records required under Sec. 516.25(a) of this title shall be kept.

Page 2 of 4 Attachment D

(k) Any deduction for the cost of safety equipment of nominal value purchased by the employee as his own property for his personal protection in his work, such as safety shoes, safety glasses, safety gloves, and hard hats, if such equipment is not required by law to be furnished by the employer, if such deduction is not violative of the Fair Labor Standards Act or prohibited by other law, if the cost on which the deduction is based does not exceed the actual cost to the employer where the equipment is purchased from him and does not include any direct or indirect monetary return to the employer where the equipment is purchased from a third person, and if the deduction is either (1) Voluntarily consented to by the employee in writing and in advance of the period in which the work is to be

done and such consent is not a condition either for the obtaining of employment or its continuance; or (2) Provided for in a bona fide collective bargaining agreement between the contractor or subcontractor and

representatives of its employees.

(5) Payroll deductions permissible with the approval of the Secretary of Labor. Any contractor or subcontractor may apply to the Secretary of Labor for permission to make any deduction not permitted under Sec. 3.5. The Secretary may grant permission whenever he finds that:

(a) The contractor, subcontractor, or any affiliated person does not make a profit or benefit directly or indirectly from the deduction either in the form of a commission, dividend, or otherwise;

(b) The deduction is not otherwise prohibited by law; (c) The deduction is either

(1) Voluntarily consented to by the employee in writing and in advance of the period in which the work is to be done and such consent is not a condition either for the obtaining of employment or its continuance, or

(2) Provided for in a bona fide collective bargaining agreement between the contractor or subcontractor and representatives of its employees; and

(d) The deduction serves the convenience and interest of the employee. (6) Applications for the approval of the Secretary of Labor. Any application for the making of payroll deductions under Sec. 3.6 shall comply with the requirements prescribed in the following paragraphs of this section:

(a) The application shall be in writing and shall be addressed to the Secretary of Labor. (b) The application need not identify the contract or contracts under which the work in question is to be performed.

Permission will be given for deductions on all current and future contracts of the applicant for a period of 1 year. A renewal of permission to make such payroll deduction will be granted upon the submission of an application which makes reference to the original application, recites the date of the Secretary of Labor’s approval of such deductions, states affirmatively that there is continued compliance with the standards set forth in the provisions of Sec. 3.6, and specifies any conditions which have changed in regard to the payroll deductions.

(c) The application shall state affirmatively that there is compliance with the standards set forth in the provisions of Sec. 3.6. The affirmation shall be accompanied by a full statement of the facts indicating such compliance.

(d) The application shall include a description of the proposed deduction, the purpose to be served thereby, and the classes of laborers or mechanics from whose wages the proposed deduction would be made.

(e) The application shall state the name and business of any third person to whom any funds obtained from the proposed deductions are to be transmitted and the affiliation of such person, if any, with the applicant.

Page 3 of 4 Attachment D

(7) Action by the Secretary of Labor upon applications. The Secretary of Labor shall decide whether or not the requested deduction is permissible under provisions of Sec. 3.6; and shall notify the applicant in writing of his decision. (8) Prohibited payroll deductions. Deductions not elsewhere provided for by this part and which are not found to be permissible under Sec. 3.6 are prohibited. (9) Methods of payment of wages.

The payment of wages shall be by cash, negotiable instruments payable on demand, or the additional forms of compensation for which deductions are permissible under this part. No other methods of payment shall be recognized on work subject to the Copeland Act. (10) Regulations part of contract. All contracts made with respect to the construction, prosecution, completion, or repair of any public building or public work or building or work financed in whole or in part by loans or grants from the United States covered by the regulations in this part shall expressly bind the contractor or subcontractor to comply with such of the regulations in this part as may be applicable. In this regard, see Sec. 5.5(a) of this subtitle.

Page 4 of 4 Attachment D

Davis-Bacon Act Contract Provisions (1) Minimum wages:

(i) All laborers and mechanics employed or working upon the site of the work (or under the United States Housing Act of 1937 or under the Housing Act of 1949 in the construction or development of the project), will be paid unconditionally and not less often than once a week, and without subsequent deduction or rebate on any account (except such payroll deductions as are permitted by regulations issued by the Secretary of Labor under the Copeland Act (29 CFR part 3)), the full amount of wages and bona fide fringe benefits (or cash equivalents thereof) due at time of payment computed at rates not less than those contained in the wage determination of the Secretary of Labor which is attached hereto and made a part hereof, regardless of any contractual relationship which may be alleged to exist between the contractor and such laborers and mechanics.

Contributions made or costs reasonably anticipated for bona fide fringe benefits under section 1(b)(2) of the Davis-Bacon Act on behalf of laborers or mechanics are considered wages paid to such laborers or mechanics, subject to the provisions of paragraph (a)(1)(iv) of this section; also, regular contributions made or costs incurred for more than a weekly period (but not less often than quarterly) under plans, funds, or programs which cover the particular weekly period, are deemed to be constructively made or incurred during such weekly period. Such laborers and mechanics shall be paid the appropriate wage rate and fringe benefits on the wage determination for the classification of work actually performed, without regard to skill, except as provided in Sec. 5.5(a)(4). Laborers or mechanics performing work in more than one classification may be compensated at the rate specified for each classification for the time actually worked therein: Provided that the employer’s payroll records accurately set forth the time spent in each classification in which work is performed. The wage determination (including any additional classification and wage rates conformed under paragraph (a)(1)(ii) of this section) and the Davis-Bacon poster (WH-1321) shall be posted at all times by the contractor and its subcontractors at the site of the work in a prominent and accessible place where it can be easily seen by the workers.

(ii) (A) The contracting officer shall require that any class of laborers or mechanics, including helpers, which is not listed in the wage determination and which is to be employed under the contract shall be classified in conformance with the wage determination. The contracting officer shall approve an additional classification and wage rate and fringe benefits therefore only when the following criteria have been met: (1) The work to be performed by the classification requested is not performed by a classification in the wage

determination; and (2) The classification is utilized in the area by the construction industry; and (3) The proposed wage rate, including any bona fide fringe benefits, bears a reasonable relationship to the wage

rates contained in the wage determination. (B) If the contractor and the laborers and mechanics to be employed in the classification (if known), or their

representatives, and the contracting officer agree on the classification and wage rate (including the amount designated for fringe benefits where appropriate), a report of the action taken shall be sent by the contracting officer to the Administrator of the Wage and Hour Division, Employment Standards Administration, U.S. Department of Labor, Washington, DC 20210. The Administrator, or an authorized representative, will approve, modify, or disapprove every additional classification action within 30 days of receipt and so advise the contracting officer or will notify the contracting officer within the 30-day period that additional time is necessary.

(C) In the event the contractor, the laborers or mechanics to be employed in the classification or their representatives, and the contracting officer do not agree on the proposed classification and wage rate (including the amount designated for fringe benefits, where appropriate), the contracting officer shall refer the questions, including the views of all interested parties and the recommendation of the contracting officer, to the Administrator for determination. The Administrator, or an authorized representative, will issue a determination within 30 days of receipt and so advise the contracting officer or will notify the contracting officer within the 30-day period that additional time is necessary.

(D) The wage rate (including fringe benefits where appropriate) determined pursuant to paragraphs (a)(1)(ii) (B) or (C) of this section, shall be paid to all workers performing work in the classification under this contract from the first day on which work is performed in the classification.

Page 1 of 6 Attachment E

(iii) Whenever the minimum wage rate prescribed in the contract for a class of laborers or mechanics includes a fringe benefit which is not expressed as an hourly rate, the contractor shall either pay the benefit as stated in the wage determination or shall pay another bona fide fringe benefit or an hourly cash equivalent thereof.

(iv) If the contractor does not make payments to a trustee or other third person, the contractor may consider as part of the wages of any laborer or mechanic the amount of any costs reasonably anticipated in providing bona fide fringe benefits under a plan or program, Provided, That the Secretary of Labor has found, upon the written request of the contractor, that the applicable standards of the Davis-Bacon Act have been met. The Secretary of Labor may require the contractor to set aside in a separate account assets for the meeting of obligations under the plan or program.

(2) Withholding: Telamon Corporation shall upon its own action or upon written request of an authorized representative of the Department of Labor withhold or cause to be withheld from the contractor under this contract or any other Federal contract with the same prime contractor, or any other federally-assisted contract subject to Davis-Bacon prevailing wage requirements, which is held by the same prime contractor, so much of the accrued payments or advances as may be considered necessary to pay laborers and mechanics, including apprentices, trainees, and helpers, employed by the contractor or any subcontractor the full amount of wages required by the contract. In the event of failure to pay any laborer or mechanic, including any apprentice, trainee, or helper, employed or working on the site of the work (or under the United States Housing Act of 1937 or under the Housing Act of 1949 in the construction or development of the project), all or part of the wages required by the contract, the (Agency) may, after written notice to the contractor, sponsor, applicant, or owner, take such action as may be necessary to cause the suspension of any further payment, advance, or guarantee of funds until such violations have ceased. (3) Payrolls and basic records:

(i) Payrolls and basic records relating thereto shall be maintained by the contractor during the course of the work and preserved for a period of three years thereafter for all laborers and mechanics working at the site of the work (or under the United States Housing Act of 1937, or under the Housing Act of 1949, in the construction or development of the project). Such records shall contain the name, address, and social security number of each such worker, his or her correct classification, hourly rates of wages paid (including rates of contributions or costs anticipated for bona fide fringe benefits or cash equivalents thereof of the types described in section 1(b) (2) (B) of the Davis-Bacon Act), daily and weekly number of hours worked, deductions made and actual wages paid. Whenever the Secretary of Labor has found under 29 CFR 5.5(a)(1)(iv) that the wages of any laborer or mechanic include the amount of any costs reasonably anticipated in providing benefits under a plan or program described in section 1(b)(2)(B) of the Davis-Bacon Act, the contractor shall maintain records which show that the commitment to provide such benefits is enforceable, that the plan or program is financially responsible, and that the plan or program has been communicated in writing to the laborers or mechanics affected, and records which show the costs anticipated or the actual cost incurred in providing such benefits. Contractors employing apprentices or trainees under approved programs shall maintain written evidence of the registration of apprenticeship programs and certification of trainee programs, the registration of the apprentices and trainees, and the ratios and wage rates prescribed in the applicable programs.

(ii) (A) The contractor shall submit weekly for each week in which any contract work is performed a copy of all payrolls to the (write in name of appropriate Federal agency) if the agency is a party to the contract, but if the agency is not such a party, the contractor will submit the payrolls to the applicant, sponsor, or owner, as the case may be, for transmission to the (write in name of agency). The payrolls submitted shall set out accurately and completely all of the information required to be maintained under Sec. 5.5(a) (3) (i) of Regulations, 29 CFR part 5. This information may be submitted in any form desired. Optional Form WH-347 is available for this purpose and may be purchased from the Superintendent of Documents (Federal Stock Number 029-005-00014-1), U.S. Government Printing Office, Washington, DC 20402. The prime contractor is responsible for the submission of copies of payrolls by all subcontractors.

Page 2 of 6 Attachment E

(B) Each payroll submitted shall be accompanied by a “Statement of Compliance,” signed by the contractor or subcontractor or his or her agent who pays or supervises the payment of the persons employed under the contract and shall certify the following: (1) That the payroll for the payroll period contains the information required to be maintained under Sec.

5.5(a)(3)(i) of Regulations, 29 CFR Part 5 and that such information is correct and complete; (2) That each laborer or mechanic (including each helper, apprentice, and trainee) employed on the contract

during the payroll period has been paid the full weekly wages earned, without rebate, either directly or indirectly, and that no deductions have been made either directly or indirectly from the full wages earned, other than permissible deductions as set forth in Regulations, 29 CFR part 3;

(3) That each laborer or mechanic has been paid not less than the applicable wage rates and fringe benefits or cash equivalents for the classification of work performed, as specified in the applicable wage determination incorporated into the contract.

(C) The weekly submission of a properly executed certification set forth on the reverse side of Optional Form

WH-347 shall satisfy the requirement for submission of the “Statement of Compliance” required by paragraph (a)(3)(ii)(B) of this section.

(D) The falsification of any of the above certifications may subject the contractor or subcontractor to civil or criminal prosecution under section 1001 of title 18 and section 231 of title 31 of the United States Code.

(iii) The contractor or subcontractor shall make the records required under paragraph (a)(3)(i) of this section available for inspection, copying, or transcription by authorized representatives of the (write the name of the agency) or the Department of Labor, and shall permit such representatives to interview employees during working hours on the job. If the contractor or subcontractor fails to submit the required records or to make them available, the Federal agency may, after written notice to the contractor, sponsor, applicant, or owner, take such action as may be necessary to cause the suspension of any further payment, advance, or guarantee of funds. Furthermore, failure to submit the required records upon request or to make such records available may be grounds for debarment action pursuant to 29 CFR 5.12.

(4) Apprentices and trainees:

(i) Apprentices. Apprentices will be permitted to work at less than the predetermined rate for the work they performed when they are employed pursuant to and individually registered in a bona fide apprenticeship program registered with the U.S. Department of Labor, Employment and Training Administration, Office of Apprenticeship Training, Employer and Labor Services, or with a State Apprenticeship Agency recognized by the Office, or if a person is employed in his or her first 90 days of probationary employment as an apprentice in such an apprenticeship program, who is not individually registered in the program, but who has been certified by the Office of Apprenticeship Training, Employer and Labor Services or a State Apprenticeship Agency (where appropriate) to be eligible for probationary employment as an apprentice. The allowable ratio of apprentices to journeymen on the job site in any craft classification shall not be greater than the ratio permitted to the contractor as to the entire work force under the registered program. Any worker listed on a payroll at an apprentice wage rate, who is not registered or otherwise employed as stated above, shall be paid not less than the applicable wage rate on the wage determination for the classification of work actually performed. In addition, any apprentice performing work on the job site in excess of the ratio permitted under the registered program shall be paid not less than the applicable wage rate on the wage determination for the work actually performed. Where a contractor is performing construction on a project in a locality other than that in which its program is registered, the ratios and wage rates (expressed in percentages of the journeyman’s hourly rate) specified in the contractor’s or subcontractor’s registered program shall be observed. Every apprentice must be paid at not less than the rate specified in the registered program for the apprentice’s level of progress, expressed as a percentage of the journeymen hourly rate specified in the applicable wage determination. Apprentices shall be paid fringe benefits in accordance with the provisions of the apprenticeship program. If the apprenticeship program does not specify fringe benefits, apprentices must be paid the full amount of fringe benefits listed on the wage determination for the applicable classification. If the Administrator determines that a different practice prevails for the applicable apprentice classification, fringes shall be paid in accordance with that determination. In the event the Office of Apprenticeship Training, Employer and Labor Services, or a State Apprenticeship Agency recognized by the Office, withdraws approval of an apprenticeship program, the contractor will no longer be permitted to utilize apprentices at less than the applicable predetermined rate for the work performed until an acceptable program is approved.

Page 3 of 6 Attachment E

(ii) Trainees. Except as provided in 29 CFR 5.16, trainees will not be permitted to work at less than the predetermined rate for the work performed unless they are employed pursuant to and individually registered in a program which has received prior approval, evidenced by formal certification by the U.S. Department of Labor, Employment and Training Administration. The ratio of trainees to journeymen on the job site shall not be greater than permitted under the plan approved by the Employment and Training Administration. Every trainee must be paid at not less than the rate specified in the approved program for the trainee’s level of progress, expressed as a percentage of the journeyman hourly rate specified in the applicable wage determination. Trainees shall be paid fringe benefits in accordance with the provisions of the trainee program. If the trainee program does not mention fringe benefits, trainees shall be paid the full amount of fringe benefits listed on the wage determination unless the Administrator of the Wage and Hour Division determines that there is an apprenticeship program associated with the corresponding journeyman wage rate on the wage determination which provides for less than full fringe benefits for apprentices. Any employee listed on the payroll at a trainee rate who is not registered and participating in a training plan approved by the Employment and Training Administration shall be paid not less than the applicable wage rate on the wage determination for the classification of work actually performed. In addition, any trainee performing work on the job site in excess of the ratio permitted under the registered program shall be paid not less than the applicable wage rate on the wage determination for the work actually performed. In the event the Employment and Training Administration withdraws approval of a training program, the contractor will no longer be permitted to utilize trainees at less than the applicable predetermined rate for the work performed until an acceptable program is approved.

(iii) Equal employment opportunity. The utilization of apprentices, trainees and journeymen under this part shall be in conformity with the equal employment opportunity requirements of Executive Order 11246, as amended, and 29 CFR part 30.

(5) Compliance with Copeland Act requirements: The contractor shall comply with the requirements of 29 CFR Part 3, which are incorporated by reference in this contract. (6) Subcontracts: The contractor or subcontractor shall insert in any subcontracts the clauses contained in 29 CFR 5.5(a)(1) through (10) and such other clauses as the Department of Labor may by appropriate instructions require, and also a clause requiring the subcontractors to include these clauses in any lower tier subcontracts. The prime contractor shall be responsible for the compliance by any subcontractor or lower tier subcontractor with all the contract clauses in 29 CFR 5.5. (7) Contract termination: debarment: A breach of the contract clauses in 29 CFR 5.5 may be grounds for termination of the contract, and for debarment as a contractor and a subcontractor as provided in 29 CFR 5.12.

Page 4 of 6 Attachment E

(8) Compliance with Davis-Bacon and Related Act requirements: All rulings and interpretations of the Davis-Bacon and Related Acts contained in 29 CFR parts 1, 3, and 5 are herein incorporated by reference in this contract.

(9) Disputes concerning labor standards: Disputes arising out of the labor standards provisions of this contract shall not be subject to the general disputes clause of this contract. Such disputes shall be resolved in accordance with the procedures of the Department of Labor set forth in 29 CFR parts 5, 6, and 7. Disputes within the meaning of this clause include disputes between the contractor (or any of its subcontractors) and the contracting agency, the U.S. Department of Labor, or the employees or their representatives.

(10) Certification of eligibility:

(i) By entering into this contract, the contractor certifies that neither it (nor he or she) nor any person or firm who has an interest in the contractor’s firm is a person or firm ineligible to be awarded Government contracts by virtue of section 3(a) of the Davis-Bacon Act or 29 CFR 5.12(a)(1).

(ii) No part of this contract shall be subcontracted to any person or firm ineligible for award of a Government contract by virtue of section 3(a) of the Davis-Bacon Act or 29 CFR 5.12(a)(1).

(iii) The penalty for making false statements is prescribed in the U.S. Criminal Code, 18 U.S.C. 1001.

(11) Contract Work Hours and Safety Standards Act:

(i) Overtime requirements. No contractor or subcontractor contracting for any part of the contract work which may require or involve the employment of laborers or mechanics shall require or permit any such laborer or mechanic in any workweek in which he or she is employed on such work to work in excess of forty hours in such workweek unless such laborer or mechanic receives compensation at a rate not less than one and one-half times the basic rate of pay for all hours worked in excess of forty hours in such workweek.

(ii) Violation; liability for unpaid wages; liquidated damages. In the event of any violation of the clause set forth in paragraph (11)(i) of this section the contractor and any subcontractor responsible therefore shall be liable for the unpaid wages. In addition, such contractor and subcontractor shall be liable to the United States (in the case of work done under contract for the District of Columbia or a territory, to such District or to such territory), for liquidated damages. Such liquidated damages shall be computed with respect to each individual laborer or mechanic, including watchmen and guards, employed in violation of the clause set forth in paragraph (11)(i) of this section, in the sum of $10 for each calendar day on which such individual was required or permitted to work in excess of the standard workweek of forty hours without payment of the overtime wages required by the clause set forth in paragraph (11)(i) of this section.

(iii) Withholding for unpaid wages and liquidated damages. Telamon Corporation shall upon its own action or upon written request of an authorized representative of the Department of Labor withhold or cause to be withheld, from any moneys payable on account of work performed by the contractor or subcontractor under any such contract or any other Federal contract with the same prime contractor, or any other federally-assisted contract subject to the Contract Work Hours and Safety Standards Act, which is held by the same prime contractor, such sums as may be determined to be necessary to satisfy any liabilities of such contractor or subcontractor for unpaid wages and liquidated damages as provided in the clause set forth in paragraph (11)(ii) of this section.

(iv) Subcontracts. The contractor or subcontractor shall insert in any subcontracts the clauses set forth in paragraph (11)(i) through (iv) of this section and also a clause requiring the subcontractors to include these clauses in any lower tier subcontracts. The prime contractor shall be responsible for compliance by any subcontractor or lower tier subcontractor with the clauses set forth in paragraphs (11)(i) through (iv) of this section.

Page 5 of 6 Attachment E

(12) Record Retention and Maintenance: In addition to the clauses contained in paragraph (11) the contractor or subcontractor shall maintain payrolls and basic payroll records during the course of the work and shall preserve them for a period of three years from the completion of the contract for all laborers and mechanics, including guards and watchmen, working on the contract. Such records shall contain the name and address of each such employee, social security number, correct classifications, hourly rates of wages paid, daily and weekly number of hours worked, deductions made, and actual wages paid. Further, the records to be maintained under this paragraph shall be made available by the contractor or subcontractor for inspection, copying, or transcription by authorized representatives of Telamon Corporation, the Department of Labor, or any other duly authorized representative and the contractor or subcontractor will permit such representatives to interview employees during working hours on the job.

Page 6 of 6 Attachment E

U.S. Department of Labor PAYROLL (For Contractor's Optional Use; See Instructions at www.dol.gov/whd/forms/wh347instr.htm)Wage and Hour Division

Persons are not required to respond to the collection of information unless it displays a currently valid OMB control number.

NAME OF CONTRACTOR OR SUBCONTRACTOR ADDRESS OMB No.: 1235-0008 Expires: 01/31/2015

PAYROLL NO. FOR WEEK ENDING PROJECT AND LOCATION PROJECT OR CONTRACT NO.

(1) (2) (3) (4) DAY AND DATE (5) (6) (7) (9) (8)

DEDUCTIONS

O

O

O

O

O

O

O

O

NAME AND INDIVIDUAL IDENTIFYING NUMBER (e.g., LAST FOUR DIGITS OF SOCIAL SECURITY

NUMBER) OF WORKER NO

. OF

WIT

HH

OLD

iNG

E

XEM

PTI

ON

S

WORK CLASSIFICATION

OT.

OR

ST.

HOURS WORKED EACH DAY TOTAL HOURS

RATE OF PAY

GROSS AMOUNT EARNED FICA

WITH-HOLDING

TAX OTHER TOTAL

DEDUCTIONS

NET WAGES

PAID FOR WEEK

S

S

S

S

S

S

S

S

Rev. Dec. 2008

Rev. Dec. 2008

While completion of Form WH-347 is optional, it is mandatory for covered contractors and subcontractors performing work on Federally financed or assisted construction contracts to respond to the information collection contained in 29 C.F.R. §§ 3.3, 5.5(a). The Copeland Act (40 U.S.C. § 3145) contractors and subcontractors performing work on Federally financed or assisted construction contracts to "furnish weekly a statement with respect to the wages paid each employee during the preceding week." U.S. Department of Labor (DOL) regulations at 29 C.F.R. § 5.5(a)(3)(ii) require contractors to submit weekly a copy of all payrolls to the Federal agency contracting for or financing the construction project, accompanied by a signed "Statement of Compliance" indicating that the payrolls are correct and complete and that each laborer or mechanic has been paid not less than the proper Davis-Bacon prevailing wage rate for the work performed. DOL and federal contracting agencies receiving this information review the information to determine that employees have received legally required wages and fringe benefits.

Public Burden Statement

We estimate that is will take an average of 55 minutes to complete this collection, including time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. If you have any comments regarding these estimates or any other aspect of this collection, including suggestions for reducing this burden, send them to the Administrator, Wage and Hour Division, U.S. Department of Labor, Room S3502, 200 Constitution Avenue, N.W. Washington, D.C. 20210

(over)

Date

I,(Name of Signatory Party) (Title)

do hereby state:

(1) That I pay or supervise the payment of the persons employed by

on the (Contractor or Subcontractor)

; that during the payroll period commencing on the (Building or Work)

day of , , and ending the day of , , all persons employed on said project have been paid the full weekly wages earned, that no rebates have been or will be made either directly or indirectly to or on behalf of said

from the full (Contractor or Subcontractor)

weekly wages earned by any person and that no deductions have been made either directly or indirectly from the full wages earned by any person, other than permissible deductions as defined in Regulations, Part 3 (29 C.F.R. Subtitle A), issued by the Secretary of Labor under the Copeland Act, as amended (48 Stat. 948, 63 Stat. 108, 72 Stat. 967; 76 Stat. 357; 40 U.S.C. § 3145), and described below:

(2) That any payrolls otherwise under this contract required to be submitted for the above period are correct and complete; that the wage rates for laborers or mechanics contained therein are not less than the applicable wage rates contained in any wage determination incorporated into the contract; that the classificationsset forth therein for each laborer or mechanic conform with the work he performed.

(3) That any apprentices employed in the above period are duly registered in a bona fide apprenticeshipprogram registered with a State apprenticeship agency recognized by the Bureau of Apprenticeship andTraining, United States Department of Labor, or if no such recognized agency exists in a State, are registeredwith the Bureau of Apprenticeship and Training, United States Department of Labor.

(4) That: (a) WHERE FRINGE BENEFITS ARE PAID TO APPROVED PLANS, FUNDS, OR PROGRAMS

− in addition to the basic hourly wage rates paid to each laborer or mechanic listed in the above referenced payroll, payments of fringe benefits as listed in the contract have been or will be made to appropriate programs for the benefit of such employees, except as noted in section 4(c) below.

(b) WHERE FRINGE BENEFITS ARE PAID IN CASH

− Each laborer or mechanic listed in the above referenced payroll has been paid, as indicated on the payroll, an amount not less than the sum of the applicable basic hourly wage rate plus the amount of the required fringe benefits as listed in the contract, except as noted in section 4(c) below.

(c) EXCEPTIONS

REMARKS:

EXCEPTION (CRAFT)

EXPLANATION

NAME AND TITLE SIGNATURE

THE WILLFUL FALSIFICATION OF ANY OF THE ABOVE STATEMENTS MAY SUBJECT THE CONTRACTOR OR SUBCONTRACTOR TO CIVIL OR CRIMINAL PROSECUTION. SEE SECTION 1001 OF TITLE 18 AND SECTION 231 OF TITLE 31 OF THE UNITED STATES CODE.

Note: These Instructions may be found online at www.dol.gov. From the DOL home page, follow the sequence of links listed below in yellow to find the Instructions page.

April 1, 2003 DOL Home > ESA > WHD > Forms > WH-347 Instructions

Instructions For Completing Payroll Form, WH-347

General: The use of the WH-347 payroll form is not mandatory. This form has been made available for the convenience of contractors and subcontractors required by their Federal or Federally aided construction-type contracts and subcontracts to submit weekly payrolls. Properly filled out, this form will satisfy the requirements of Regulations, Parts 3 and 5 (29 CFR, Subtitle A), as to payrolls submitted in connection with contracts subject to the Davis-Bacon and related Acts.

This form meets needs resulting from the amendment of Davis-Bacon Act to include fringe benefits provisions. Under this amended law, the contractor is required to pay not less than fringe benefits as predetermined by the Department of Labor, in addition to payment of not less than the predetermined rates. The contractor's obligation to pay fringe benefits may be met either by payment of the fringes to the various plans, funds or programs or by making these payments to the employees as cash in lieu of fringes.

This payroll provides for the contractor's showing on the face of the payroll all monies to the employees, whether as basic rates or as cash in lieu of fringes and provides for the contractor's representation in the statement of compliance on the rear of the payroll that he is paying to other fringes required by the contract and not paid as cash in lieu of fringes. Detailed instructions concerning the preparation of the payroll follow:

Contractor or Subcontractor: Fill in your firm's name and check appropriate box.

Address: Fill in your firm's address.

Column 1 - Name, Address, and Social Security Number of Employee: The employee's full name and Social Security Number must be shown on each weekly payroll submitted. The employee's address must also be shown on the payroll covering the first week in which the employee works on the project. The address need not be shown on subsequent weekly payrolls unless the address changes.

Column 2 - Withholding Exemptions: This column is merely inserted for the employer's convenience and is not a requirement of Regulations, Part 3 and 5.

Column 3 - Work Classifications: List classification descriptive of work actually performed by employees. Consult classification and minimum wage schedule set forth in contract specifications. If additional classifications are deemed necessary, see Contracting Officer or Agency representative. Employee may be shown as having worked in more than one classification provided accurate breakdown or hours so worked is maintained and shown on submitted payroll by use of separate entries.

Column 4 - Hours worked: On all contracts subject to the Contract Work Hours Standard Act enter as overtime hours worked in excess of 8 hours per day and 40 hours a week.

Column 5 - Total: Self-explanatory

Column 6 - Rate of Pay, including Fringe Benefits: In straight time box, list actual hourly rate paid the employee for straight time worked plus in cash in lieu of fringes paid the employee. When recording the straight time hourly rate, any cash paid in lieu of fringes may be shown separately from the basic rate, thus $3.25/.40. This is of assistance in correctly computing overtime. See "Fringe Benefits" below. In overtime box shown overtime hourly rate paid, plus any cash in lieu of fringes paid the employee. See "Fringe Benefits" below. Payment of not less than time and one-half the basic or regular rate paid is required for overtime under the Contract Work Hours Standard Act of 1962. In addition to paying no less than the predetermined rate for the classification which the employee works, the contractor shall pay to approved plans, funds or

Attachment F

programs or shall pay as cash in lieu of fringes amounts predetermined as fringe benefits in the wage decision made part of the contract. See "FRINGE BENEFITS" below.

FRINGE BENEFITS - Contractors who pay all required fringe benefits: A contractor who pays fringe benefits to approved plans, funds, or programs in amounts not less than were determined in the applicable wage decision of the Secretary of labor shall continue to show on the face of the payroll the basic cash hourly rate and overtime rate paid to his employees just as he has always done. Such a contractor shall check paragraph 4(a) of the statement on the reverse of the payroll to indicate that he is also paying to approved plans, funds or programs not less than the amount predetermined as fringe benefits for each craft. Any exceptions shall be noted in section 4(c).

Contractors who pay no fringe benefits: A contractor who pays no fringe benefits shall pay to the employee, and insert in the straight time hourly rate column of the payroll, an amount not less than the predetermined rate for each classification plus the amount of fringe benefits determined for each classification in the applicable wage decision. Inasmuch as it is not necessary to pay time and a half on cash paid in lieu of fringes, the overtime rate shall be not less than the sum of the basic predetermined rate, plus the half time premium on basic or regular rate, plus the required cash in lieu of fringes at the straight time rate. In addition, the contractor shall check paragraph 4(b) of the statement on the reverse of the payroll to indicate that he is paying fringe benefits in cash directly to his employees. Any exceptions shall be noted in Section 4(c).

Use of Section 4(c), Exceptions

Any contractor who is making payment to approved plans, funds, or programs in amounts less than the wage determination requires is obliged to pay the deficiency directly to the employees as cash in lieu of fringes. Any exceptions to Section 4(a) or 4(b), whichever the contractor may check, shall be entered in section 4(c). Enter in the Exception column the craft, and enter in the Explanation column the hourly amount paid the employee as cash in lieu of fringes and the hourly amount paid to plans, funds, or programs as fringes. The contractor shall pay, and shall show that he is paying to each such employee for all hours (unless otherwise provided by applicable determination) worked on Federal or Federally assisted project an amount not less than the predetermined rate plus cash in lieu of fringes as shown in Section 4(c). The rate paid and amount of cash paid in lieu of fringe benefits per hour should be entered in column 6 on the payroll. See paragraph on "Contractors who pay no fringe benefits" for computation of overtime rate.

Column 7 - Gross Amount Earned: Enter gross amount earned on this project. If part of the employees' weekly wage was earned on projects other than the project described on this payroll, enter in column 7 first the amount earned on the Federal or Federally assisted project and then the gross amount earned during the week on all projects, thus $63.00/$120.00.

Column 8 - Deductions: Five columns are provided for showing deductions made. If more than five deductions should be involved, use first 4 columns; show the balance deductions under "Other" column; show actual total under "Total Deductions" column: and in the attachment to the payroll describe the deduction contained in the "Other" column. All deductions must be in accordance with the provisions of the Copeland Act Regulations, 29 CFR, Part 3. If the employee worked on other jobs in addition to this project, show actual deductions from his weekly gross wage, but indicate that deductions are based on his gross wages.

Column 9 - Net Wages Paid for Week: Self-explanatory

Totals - Space has been left at the bottom of the columns so that totals may be shown if the contractor so desires.

Statement Required by Regulations, Parts 3 and 5: While this form need not be notarized, the statement on the back of the payroll is subject to the penalties provided by 18 USV 1001, namely, possible imprisonment of 5 years or $10,000.00 fine or both. Accordingly, the party signing this statement should have knowledge of the facts represented as true.

Space has been provided between items (1) and (2) of the statement for describing any deductions made. If all deductions made are adequately described in the "Deductions" column above, state "See Deductions column in this payroll." See paragraph entitled "FRINGE BENEFITS" above for instructions concerning filling out paragraph 4 of the statement.

U.S. Department of Labor Frances Perkins Building 200 Constitution Avenue, NW Washington, DC 20210 1-866-4-USWAGE TTY: 1-866-487-9243

Attachment F

Exhibit H

UNCONDITIONAL WAIVER AND RELEASE UPON FINAL PAYMENT

The undersigned has been paid in full for all labor, services, equipment or material furnished to Telamon Corporation for the job located at: ____________________________________________ except for final payment of $__________________ and does hereby release any right to a mechanic's lien, stop notice, or any right against a labor and material bond on the job. This document also releases ________________________________ from liability with subcontractors signed below. (Contractor) Dated: ______________ Company Name: ________________________________ _____________________________________ _________________________ Signature of Authorized Person Title NOTICE TO PERSONS SIGNING THIS WAIVER: This document waives your rights unconditionally and states that you have been paid for giving up those rights. This document is enforceable against you if you sign it, even if you have not been paid. THE UNDERSIGNED HAVE PERFORMED/PROVIDED EITHER LABOR, SERVICES, EQUIPMENT, OR MATERIALS ON THE PROJECT DESCRIBED ABOVE AND HAVE BEEN PAID IN FULL TO DATE ___________________________________ ______________________ (Company Name) (Title) _______________________________________________ _____________ (Signature of Subcontractor) (Date) ___________________________________ ______________________ (Company Name) (Title) ________________________________________________ _____________ (Signature of Subcontractor) (Date) ___________________________________ ______________________ (Company Name) (Title) ________________________________________________ _____________ (Signature of Subcontractor) (Date) ___________________________________ ______________________ (Company Name) (Title)

Attachment D

Attachment E

Honeywell WEBs

SECTION 15900 TEMPERATURE CONTROL SYSTEM (TCS)

and

FACILITY MANAGEMENT CONTROL SYSTEM (FMCS)

Note to Specifiers: This specification is intended to provide a means to delineate the scope of work between the Division 15 contractor, typically the Temperature Controls Contractor and other divisions supplying products and services that will become part of the overall FMCS. This section must be closely coordinated with Division 16. If other systems are planned for integration, such as lighting, access, fire, etc., please add the appropriate documentation in those sections.

This section may also be used to cover the integration of multiple systems supplied by different vendors to facilitate multiple phase bidding and/or multiple site bidding for a single owner. Depending on the type of configuration and specific project requirements, you may delete Items of this specification as appropriate.

PART 1 GENERAL

1.1 SUMMARY

A. Furnish all labor, materials, equipment, and service necessary for a complete and operating Temperature

Control System (TCS) and Facility Management system (FMCS), utilizing Direct Digital Controls as

shown on the drawings and as described herein. Drawings are diagrammatic only.

B. All labor, material, equipment and software not specifically referred to herein or on the plans, that is

required to meet the functional intent of this specification, shall be provided without additional cost to

the Owner.

C. The Owner shall be the named license holder of all software associated with any and all incremental

work on the project(s).

1.2 SYSTEM DESCRIPTION

A. The entire Temperature Control System (TCS) shall be comprised of a network of interoperable, stand-

alone digital controllers communicating via LonMark/LonTalk communication protocols to a Network

Area Controller (NAC). Temperature Control System products shall be manufactured by Honeywell.

Equivalent LonWorks products must be approved in writing by the consulting Engineer and be

submitted for approval ten (10) days prior to the date of the bid submittal.

B. The Facility Management and Control System (FMCS) shall be comprised of Network Area Controller

or Controllers (NAC) within each facility. The NAC shall connect to the owner’s local or wide area

network, depending on configuration. Access to the system, either locally in each building, or remotely

from a central site or sites, shall be accomplished through standard Web browsers, via the Internet

and/or local area network. Each NAC shall communicate to LonMark/LonTalk (IDC) and/or BACnet

(IBC) controllers and other open protocol systems/devices provided under Division 15 or Division 16.

C. The Facility Management and Control System (FMCS) as provided in this Division shall be based on

the Honeywell WEBs System incorporating the Niagara Framework™. Equivalent products must be

Attachment E

approved in writing by the consulting Engineer and be submitted for approval ten (10) days prior to the

date of the bid submittal. Systems not developed on the Niagara Framework platform are unacceptable.

1.3 SUBMITTAL

A. Eight copies of shop drawings of the components and devices for the entire control system shall be

submitted and shall consist of a complete list of equipment and materials, including manufacturers

catalog data sheets and installation instructions for all controllers, valves, dampers, sensors, routers, etc.

Shop drawings shall also contain complete wiring and schematic diagrams, software descriptions,

calculations, and any other details required to demonstrate that the system has been coordinated and will

properly function as a system. Terminal identification for all control wiring shall be shown on the shop

drawings. A complete written Sequence of Operation shall also be included with the submittal package.

Division 16 contractors supplying products and systems, as part of their packages shall provide catalog

data sheets, wiring diagrams and point lists to the Division 15 contractor for proper coordination of

work.

B. Submittal shall also include a trunk cable schematic diagram depicting operator workstations, control

panel locations and a description of the communication type, media and protocol. Though the Division

15 and 16 contractors shall provide these diagrams for their portions of work, the Systems Integrator

shall be responsible for integrating those diagrams into the overall trunk cable schematic diagrams for

the entire Wide Area Network (WAN).

C. Submittal shall also include a complete point list of all points to be connected to the TCS and FMCS.

Division 15 and 16 contractors shall provide necessary point lists, protocol documentation, and factory

support information for systems provided in their respective divisions but integrated into the FMCS.

D. Submittal shall also include a copy of each of the graphics developed for the Graphic User Interface

including a flowchart (site map) indicating how the graphics are to be linked to one another for system

navigation. The graphics are intended to be 80% - 90% complete at this stage with the only remaining

changes to be based on review comments from the A/E design team and/or Owner.

E. Upon completion of the work, provide a complete set of ‘as-built’ drawings and application software on

compact disk. Drawings shall be provided as AutoCAD™ or Visio™ compatible files. Eight copies of

the ‘as-built’ drawings shall be provided in addition to the documents on compact disk. Division 15 and

16 contractors shall provide as-builts for their portions of work. The Division 15 contractor shall be

responsible for as-builts pertaining to overall TCS and FMCS architecture and network diagrams. All as

built drawings shall also be installed into the FMCS server in a dedicated directory.

1.4 SPECIFICATION NOMENCLATURE

A. Acronyms used in this specification are as follows:

FMCS Facility Management and Control System

TCS Temperature Control System

NAC Network Area Controller

IDC Interoperable Digital Controller

IBC Interoperable BACnet Controller

GUI Graphical User Interface

WBI Web Browser Interface

POT Portable Operator’s Terminal

PMI Power Measurement Interface

DDC Direct Digital Controls

Attachment E

LAN Local Area Network

WAN Wide Area Network

OOT Object Oriented Technology

PICS Product Interoperability Compliance Statement

1.5 DIVISION OF WORK

A. The Division 15 and 16 (if applicable) contractors shall be responsible for all controllers (IDC and IBC),

control devices, control panels, controller programming, controller programming software, controller

input/output and power wiring and controller network wiring.

B. The Division 15 contractor shall be responsible for the Network Area Controller(s) (NAC), software and

programming of the NAC, graphical user interface software (GUI), development of all graphical

screens, Web browser pages, setup of schedules, logs and alarms, LonWorks network management and

connection of the NAC to the local or wide area network.

1.6 RELATED WORK SPECIFIED ELSEWHERE

A. Division 16, Electrical:

1. Providing motor starters and disconnect switches (unless otherwise noted).

2. Power wiring and conduit (unless otherwise noted).

3. Provision, installation and wiring of smoke detectors (unless otherwise noted).

4. Other equipment and wiring as specified in Division 16.

1.7 AGENCY AND CODE APPROVALS

A. All products of the TCS and FMCS shall be provided with the following agency approvals. Verification

that the approvals exist for all submitted products shall be provided with the submittal package.

Systems or products not currently offering the following approvals are not acceptable.

1. UL-916; Energy Management Systems

2. C-UL listed to Canadian Standards Association C22.2 No. 205-M1983 “signal Equipment”

3. CE

4. FCC, Part 15, Subpart J, Class A Computing Devices

1.8 SOFTWARE LICENSE AGREEMENT

A. The Owner shall agree to the manufacturer's standard software and firmware licensing agreement as a

condition of this contract. Such license shall grant use of all programs and application software to

Owner as defined by the manufacturer's license agreement, but shall protect manufacturer's rights to

disclosure of trade secrets contained within such software.

B. The Owner shall be the named license holder of all software associated with any and all incremental

work on the project(s). In addition, the Owner shall receive ownership of all job specific configuration

documentation, data files, and application-level software developed for the project. This shall include

all custom, job specific software code and documentation for all configuration and programming that is

generated for a given project and/or configured for use with the NAC, FMCS Server(s), and any related

LAN / WAN / Intranet and Internet connected routers and devices. Any and all required IDs and

passwords for access to any component or software program shall be provided to the owner. The owner

Attachment E

shall determine which organizations to be named in the SI organization ID (“orgid”) of all software

licenses. Owner shall be free to direct the modification of the “orgid” in any software license, regardless

of supplier.

1.9 DELIVERY, STORAGE AND HANDLING

A. Provide factory-shipping cartons for each piece of equipment and control device. Maintain cartons

through shipping, storage, and handling as required to prevent equipment damage. Store equipment and

materials inside and protected from weather.

1.10 JOB CONDITIONS

A. Cooperation with Other Trades: Coordinate the Work of this section with that of other sections to ensure

that the Work will be carried out in an orderly fashion. It shall be this Contractor's responsibility to

check the Contract Documents for possible conflicts between his Work and that of other crafts in

equipment location, pipe, duct and conduit runs, electrical outlets and fixtures, air diffusers, and

structural and architectural features.

PART 2 MATERIALS

2.1 GENERAL

A. The Temperature Control System (TCS) and Facility Management Control System (FMCS) shall be

comprised of a network of interoperable, stand-alone digital controllers, a computer system, graphical

user interface software, printers, network devices, valves, dampers, sensors, and other devices as

specified herein. All systems and software within FMCS shall be Year 2000 compliant and shall be

supported by compliance documentation from the manufacturer.

B. The installed system shall provide secure password access to all features, functions and data contained

in the overall FMCS.

2.2 OPEN, INTEROPERABLE, INTEGRATED ARCHITECTURES

A. The intent of this specification is to provide a peer-to-peer networked, stand-alone, distributed control

system with the capability to integrate ANSI/ASHRAE Standard 135-2001 BACnet, LonWorks

technology, MODBUS, OPC, and other open and proprietary communication protocols in one open,

interoperable system.

B. The supplied computer software shall employ object-oriented technology (OOT) for representation of

all data and control devices within the system. In addition, adherence to industry standards including

ANSI / ASHRAE™ Standard 135-2001, BACnet and LonMark to assure interoperability between all

system components is required. For each LonWorks device that does not have LonMark certification,

the device supplier must provide an XIF file and a resource file for the device. For each BACnet

device, the device supplier must provide a PICS document showing the installed device’s compliance

level. Minimum compliance is Level 3; with the ability to support data read and write functionality.

Physical connection of BACnet devices shall be via Ethernet (BACnet Ethernet/IP,) and/or RS-485

(BACnet MSTP) as specified.

C. All components and controllers supplied under this Division shall be true “peer-to-peer” communicating

devices. Components or controllers requiring “polling” by a host to pass data shall not be acceptable.

Attachment E

D. The supplied system must incorporate the ability to access all data using standard Web browsers without

requiring proprietary operator interface and configuration programs. An Open DataBase Connectivity

(ODBC) or Structured Query Language (SQL) compliant server database is required for all system

database parameter storage. This data shall reside on a supplier-installed server for all database access.

Systems requiring proprietary database and user interface programs shall not be acceptable.

E. A hierarchical topology is required to assure reasonable system response times and to manage the flow

and sharing of data without unduly burdening the customer’s internal Intranet network. Systems

employing a “flat” single tiered architecture shall not be acceptable.

1. Maximum acceptable response time from any alarm occurrence (at the point of origin) to the point

of annunciation shall not exceed 5 seconds for network connected user interfaces.

2. Maximum acceptable response time from any alarm occurrence (at the point of origin) to the point

of annunciation shall not exceed 60 seconds for remote or dial-up connected user interfaces.

Note to specifiers: There are many possible network configurations. For common Local Area Networks (LAN), use paragraph A. For Wide Area Networks (WAN), specific information about the customer’s network configuration will be needed to properly specify equipment and connections required. See the Niagara Specifier’s Reference for sample configurations. 2.3 NETWORKS

A. The Local Area Network (LAN) shall be a 100 Megabits/sec Ethernet network supporting BACnet,

Java, XML, HTTP, and SOAP for maximum flexibility for integration of building data with enterprise

information systems and providing support for multiple Network Area Controllers (NACs), user

workstations and, if specified, a local server.

B. Local area network minimum physical and media access requirements:

1. Ethernet; IEEE standard 802.3

2. Cable; 100 Base-T, UTP-8 wire, category 5

3. Minimum throughput; 100 Mbps.

2.4 NETWORK ACCESS

A. Remote Access.

1. For Local Area Network installations, provide access to the LAN from a remote location, via the

Internet. The Owner shall provide a connection to the Internet to enable this access via high speed

cable modem, asynchronous digital subscriber line (ADSL) modem, ISDN line, T1 Line or via the

customer’s Intranet to a corporate server providing access to an Internet Service Provider (ISP).

Customer agrees to pay monthly access charges for connection and ISP.

2.5 NETWORK AREA CONTROLLER (NAC)

A. The Division 17 contractor shall supply one or more Network Area Controllers (NAC) as part of this

contract. Number of area controllers required is dependent on the type and quantity of devices provided

under Divisions 15 and 16. It is the responsibility of the Division 17 contractor to coordinate with the

Division 15 and 16 contractors to determine the quantity and type of devices.

Attachment E

B. The Network Area Controller (NAC) shall provide the interface between the LAN or WAN and the field

control devices, and provide global supervisory control functions over the control devices connected to

the NAC. It shall be capable of executing application control programs to provide:

1. Calendar functions

2. Scheduling

3. Trending

4. Alarm monitoring and routing

5. Time synchronization

6. Integration of LonWorks controller data and BACnet controller data

7. Network Management functions for all LonWorks based devices

C. The Network Area Controller must provide the following hardware features as a minimum:

1. One Ethernet Port – 10/100 Mbps

2. One RS-232 port

3. One LonWorks Interface Port – 78KB FTT-10A

4. One RS-485 ports

5. Battery Backup

6. Flash memory for long term data backup (If battery backup or flash memory is not supplied, the

controller must contain a hard disk with at least 1 gigabyte storage capacity)

7. The NAC must be capable of operation over a temperature range of 32 to 122°F

8. The NAC must be capable of withstanding storage temperatures of between 0 and 158°F

9. The NAC must be capable of operation over a humidity range of 5 to 95% RH, non-condensing

D. The NAC shall provide multiple user access to the system and support for ODBC or SQL. A database

resident on the NAC shall be an ODBC-compliant database or must provide an ODBC data access

mechanism to read and write data stored within it.

E. The NAC shall support standard Web browser access via the Intranet/Internet. It shall support a

minimum of 32 simultaneous users.

F. Event Alarm Notification and actions

1. The NAC shall provide alarm recognition, storage; routing, management, and analysis to

supplement distributed capabilities of equipment or application specific controllers.

2. The NAC shall be able to route any alarm condition to any defined user location whether

connected to a local network or remote via dial-up telephone connection, or wide-area network.

3. Alarm generation shall be selectable for annunciation type and acknowledgement requirements

including but limited to:

a. To alarm

b. Return to normal

c. To fault

Attachment E

4. Provide for the creation of a minimum of eight of alarm classes for the purpose of routing types

and or classes of alarms, i.e.: security, HVAC, Fire, etc.

5. Provide timed (schedule) routing of alarms by class, object, group, or node.

6. Provide alarm generation from binary object “runtime” and /or event counts for equipment

maintenance. The user shall be able to reset runtime or event count values with appropriate

password control.

G. Control equipment and network failures shall be treated as alarms and annunciated.

H. Alarms shall be annunciated in any of the following manners as defined by the user:

1. Screen message text

2. Email of the complete alarm message to multiple recipients. Provide the ability to route and email

alarms based on:

a. Day of week

b. Time of day

c. Recipient

3. Pagers via paging services that initiate a page on receipt of email message

4. Graphic with flashing alarm object(s)

5. Printed message, routed directly to a dedicated alarm printer

I. The following shall be recorded by the NAC for each alarm (at a minimum):

1. Time and date

2. Location (building, floor, zone, office number, etc.)

3. Equipment (air handler #, accessway, etc.)

4. Acknowledge time, date, and user who issued acknowledgement.

5. Number of occurrences since last acknowledgement.

J. Alarm actions may be initiated by user defined programmable objects created for that purpose.

K. Defined users shall be given proper access to acknowledge any alarm, or specific types or classes of

alarms defined by the user.

L. A log of all alarms shall be maintained by the NAC and/or a server (if configured in the system) and

shall be available for review by the user.

M. Provide a “query” feature to allow review of specific alarms by user defined parameters.

N. A separate log for system alerts (controller failures, network failures, etc.) shall be provided and

available for review by the user.

O. An Error Log to record invalid property changes or commands shall be provided and available for

review by the user.

2.6 Data Collection and Storage

A. The NAC shall have the ability to collect data for any property of any object and store this data for

future use.

B. The data collection shall be performed by log objects, resident in the NAC that shall have, at a

minimum, the following configurable properties:

Attachment E

1. Designating the log as interval or deviation.

2. For interval logs, the object shall be configured for time of day, day of week and the sample

collection interval.

3. For deviation logs, the object shall be configured for the deviation of a variable to a fixed value.

This value, when reached, will initiate logging of the object.

4. For all logs, provide the ability to set the maximum number of data stores for the log and to set

whether the log will stop collecting when full, or rollover the data on a first-in, first-out basis.

5. Each log shall have the ability to have its data cleared on a time-based event or by a user-defined

event or action.

C. All log data shall be stored in a relational database in the NAC and the data shall be accessed from a

server (if the system is so configured) or a standard Web browser.

D. All log data, when accessed from a server, shall be capable of being manipulated using standard SQL

statements.

E. All log data shall be available to the user in the following data formats:

1. HTML

2. XML

3. Plain Text

4. Comma or tab separated values

F. Systems that do not provide log data in HTML and XML formats at a minimum shall not be acceptable.

G. The NAC shall have the ability to archive its log data either locally (to itself), or remotely to a server or

other NAC on the network. Provide the ability to configure the following archiving properties, at a

minimum:

1. Archive on time of day

2. Archive on user-defined number of data stores in the log (buffer size)

3. Archive when log has reached it’s user-defined capacity of data stores

4. Provide ability to clear logs once archived

2.7 AUDIT LOG

A. Provide and maintain an Audit Log that tracks all activities performed on the NAC. Provide the ability

to specify a buffer size for the log and the ability to archive log based on time or when the log has

reached its user-defined buffer size. Provide the ability to archive the log locally (to the NAC), to

another NAC on the network, or to a server. For each log entry, provide the following data:

1. Time and date

2. User ID

3. Change or activity: i.e., Change setpoint, add or delete objects, commands, etc.

2.8 DATABASE BACKUP AND STORAGE

A. The NAC shall have the ability to automatically backup its database. The database shall be backed up

based on a user-defined time interval.

B. Copies of the current database and, at the most recently saved database shall be stored in the NAC. The

age of the most recently saved database is dependent on the user-defined database save interval.

Attachment E

C. The NAC database shall be stored, at a minimum, in XML format to allow for user viewing and editing,

if desired. Other formats are acceptable as well, as long as XML format is supported.

Note to specifiers: See Appendix A for specific control sequences for each unitary controller required for this installation. Insert desired control sequences where needed in the Interoperable digital controller section.

2.9 INTEROPERABLE DIGITAL CONTROLLER (IDC)

A. Controls shall be Honeywell Excel 10 microprocessor based Interoperable LonWorks Controllers (IDC)

or approved equal. Where possible, all Interoperable Digital Controllers shall bear the applicable

LonMark interoperability logo on each product delivered.

B. HVAC control shall be accomplished using LonMark based devices where the application has a

LonMark profile defined. Where LonMark devices are not available for a particular application, devices

based on LonWorks shall be acceptable. For each LonWorks device that does not have LonMark

certification, the device supplier must provide an XIF file for the device. Publicly available

specifications for the Applications Programming Interface (API) must be provided for each LonWorks /

LonMark controller defining the programming or setup of each device. The Division 15 contractor shall

provide all programming, documentation and programming tools necessary to set up and configure the

supplied devices per the specified sequences of operation.

C. The Division 15 contractor shall run the LonWorks network trunk to the nearest Network Area

Controller (NAC). Coordinate locations of the NAC to ensure that maximum network wiring distances,

as specified by the LonWorks wiring guidelines, are not exceeded. A maximum of 126 devices may

occupy any one LonWorks trunk and must be installed using the appropriate trunk termination device.

All LonWorks and LonMark devices must be supplied using FTT-10A LonWorks communications

transceivers.

D. The Network Area Controller (NAC) will provide all scheduling, alarming, trending, and network

management for the LonMark / LonWorks based devices.

E. The IDCs shall communicate with the NAC at a baud rate of not less than 78.8K baud. The IDC shall

provide LED indication of communication and controller performance to the technician, without cover

removal.

F. All IDCs shall be fully application programmable and shall at all times maintain their LONMARK

certification, if so certified. Controllers offering application selection only (non-programmable), require

a 10% spare point capacity to be provided for all applications. All control sequences within or

programmed into the IDC shall be stored in non-volatile memory, which is not dependent upon the

presence of a battery, to be retained.

G. The Division 15 contractor supplying the IDC’s shall provide documentation for each device, with the

following information at a minimum:

1. Network Variable Inputs (nvi’s); name and type

2. Network Variable Outputs (nvo’s); name and type

3. Network configuration parameters (nci, nco); name and type

H. It is the responsibility of the Division 15 contractor to ensure that the proper Network Variable Inputs

and Outputs (nvi and nvo) are provided in each IDC, as required by the point charts.

I. The supplier of any programmable IDC shall provide one copy of the manufacturer’s programming tool,

with documentation, to the owner.

Attachment E

Note to specifiers: Depending on the project configuration and requirements, a Graphical User Interface (GUI) software application can be specified. If this is desired, use Item 2.9. Alternatively, the user interface software can be a standard Web browser (WBI) such as Microsoft Internet Explorer or Netscape Navigator. If this is the desired method, use Item 2.10. You can also specify a configuration where both the Graphical User Interface Software and Web browsers are used to interface with the system. If this is the case, use both Items 2.9 and 2.10.

2.10 GRAPHICAL USER INTERFACE SOFTWARE

A. Operating System:

1. The GUI shall run on Microsoft Windows XP Professional.

B. The GUI shall employ browser-like functionality for ease of navigation. It shall include a tree view

(similar to Windows Explorer) for quick viewing of, and access to, the hierarchical structure of the

database. In addition, menu-pull downs, and toolbars shall employ buttons, commands and navigation

to permit the operator to perform tasks with a minimum knowledge of the HVAC Control System and

basic computing skills. These shall include, but are not limited to, forward/backward buttons, home

button, and a context sensitive locator line (similar to a URL line), that displays the location and the

selected object identification.

C. Real-Time Displays. The GUI, shall at a minimum, support the following graphical features and

functions:

1. Graphic screens shall be developed using any drawing package capable of generating a GIF, BMP,

or JPG file format. Use of proprietary graphic file formats shall not be acceptable. In addition to,

or in lieu of a graphic background, the GUI shall support the use of scanned pictures.

2. Graphic screens shall have the capability to contain objects for text, real-time values, animation,

color spectrum objects, logs, graphs, HTML or XML document links, schedule objects, hyperlinks

to other URL’s, and links to other graphic screens.

3. Graphics shall support layering and each graphic object shall be configurable for assignment to a

layer. A minimum of six layers shall be supported.

4. Modifying common application objects, such as schedules, calendars, and set points shall be

accomplished in a graphical manner.

a. Schedule times will be adjusted using a graphical slider, without requiring any keyboard

entry from the operator.

b. Holidays shall be set by using a graphical calendar without requiring any keyboard entry

from the operator.

5. Commands to start and stop binary objects shall be done by right-clicking the selected object and

selecting the appropriate command from the pop-up menu. No entry of text shall be required.

6. Adjustments to analog objects, such as set points, shall be done by right-clicking the selected

object and using a graphical slider to adjust the value. No entry of text shall be required.

D. System Configuration. At a minimum, the GUI shall permit the operator to perform the following tasks,

with proper password access:

a. Create, delete or modify control strategies.

b. Add/delete objects to the system.

Attachment E

c. Tune control loops through the adjustment of control loop parameters.

d. Enable or disable control strategies.

e. Generate hard copy records or control strategies on a printer.

f. Select points to be alarmable and define the alarm state.

g. Select points to be trended over a period of time and initiate the recording of values

automatically.

E. On-Line Help. Provide a context sensitive, on-line help system to assist the operator in operation and

editing of the system. On-line help shall be available for all applications and shall provide the relevant

data for that particular screen. Additional help information shall be available through the use of

hypertext. All system documentation and help files shall be in HTML format.

F. Security. Each operator shall be required to log on to that system with a user name and password in

order to view, edit, add, or delete data. System security shall be selectable for each operator. The

system administrator shall have the ability to set passwords and security levels for all other operators.

Each operator password shall be able to restrict the operators’ access for viewing and/or changing each

system application, full screen editor, and object. Each operator shall automatically be logged off of the

system if no keyboard or mouse activity is detected. This auto log-off time shall be set per operator

password. All system security data shall be stored in an encrypted format.

G. System Diagnostics. The system shall automatically monitor the operation of all workstations, printers,

modems, network connections, building management panels, and controllers. The failure of any device

shall be annunciated to the operator.

H. Alarm Console

1. The system will be provided with a dedicated alarm window or console. This window will notify

the operator of an alarm condition, and allow the operator to view details of the alarm and

acknowledge the alarm. The use of the Alarm Console can be enabled or disabled by the system

administrator.

2. When the Alarm Console is enabled, a separate alarm notification window will supercede all other

windows on the desktop and shall not be capable of being minimized or closed by the operator.

This window will notify the operator of new alarms and un-acknowledged alarms. Alarm

notification windows or banners that can be minimized or closed by the operator shall not be

acceptable.

2.11 WEB BROWSER CLIENTS

A. The system shall be capable of supporting an unlimited number of clients using a standard Web browser

such as Internet Explorer™ or Netscape Navigator™. Systems requiring additional software (to enable

a standard Web browser) to be resident on the client machine, or manufacture-specific browsers shall

not be acceptable.

B. The Web browser software shall run on any operating system and system configuration that is supported

by the Web browser. Systems that require specific machine requirements in terms of processor speed,

memory, etc., in order to allow the Web browser to function with the FMCS, shall not be acceptable.

C. The Web browser shall provide the same view of the system, in terms of graphics, schedules, calendars,

logs, etc., and provide the same interface methodology as is provided by the Graphical User Interface.

Systems that require different views or that require different means of interacting with objects such as

schedules, or logs, shall not be permitted.

D. The Web browser client shall support at a minimum, the following functions:

Attachment E

1. User log-on identification and password shall be required. If an unauthorized user attempts access,

a blank web page shall be displayed. Security using Java authentication and encryption techniques

to prevent unauthorized access shall be implemented.

2. Graphical screens developed for the GUI shall be the same screens used for the Web browser

client. Any animated graphical objects supported by the GUI shall be supported by the Web

browser interface.

3. HTML programming shall not be required to display system graphics or data on a Web page.

HTML editing of the Web page shall be allowed if the user desires a specific look or format.

4. Storage of the graphical screens shall be in the Network Area Controller (NAC), without requiring

any graphics to be stored on the client machine. Systems that require graphics storage on each

client are not acceptable.

5. Real-time values displayed on a Web page shall update automatically without requiring a manual

“refresh” of the Web page.

6. Users shall have administrator-defined access privileges. Depending on the access privileges

assigned, the user shall be able to perform the following:

a. Modify common application objects, such as schedules, calendars, and set points in a

graphical manner.

1. Schedule times will be adjusted using a graphical slider, without requiring any

keyboard entry from the operator.

2. Holidays shall be set by using a graphical calendar, without requiring any keyboard

entry from the operator.

b. Commands to start and stop binary objects shall be done by right-clicking the selected object

and selecting the appropriate command from the pop-up menu. No entry of text shall be

required.

c. View logs and charts

d. View and acknowledge alarms

e. Setup and execute SQL queries on log and archive information

7. The system shall provide the capability to specify a user’s (as determined by the log-on user

identification) home page. Provide the ability to limit a specific user to just their defined home

page. From the home page, links to other views, or pages in the system shall be possible, if

allowed by the system administrator.

8. Graphic screens on the Web Browser client shall support hypertext links to other locations on the

Internet or on Intranet sites, by specifying the Uniform Resource Locator (URL) for the desired

link.

Note to specifiers: Depending on the project configuration and requirements, a central server may be desired. Typically a server is used on projects where there are multiple Network Area Controllers (NAC) connected locally over a LAN, or remotely over a WAN. The server provides time synchronization, file archiving, and other features for overall system administration. If this is desired, use Item 2.11. See the Niagara Specifier’s Reference for sample configurations.

Attachment E

2.12 SERVER FUNCTIONS AND HARDWARE

A. A central server, located (in, at) ____________________, shall be provided. The server shall support

all Network Area Controllers (NAC) connected to the customer’s network whether local or remote.

B. Local connections shall be via an Ethernet LAN. Remote connections can be via ISDN, ADSL, T1 or

dial-up connection.

C. It shall be possible to provide access to all Network Area Controllers via a single connection to the

server. In this configuration, each Network Area Controller can be accessed from a remote Graphical

User Interface (GUI) or from a standard Web browser (WBI) by connecting to the server.

D. The server shall provide the following functions, at a minimum:

1. Global Data Access: The server shall provide complete access to distributed data defined

anywhere in the system.

2. Distributed Control: The server shall provide the ability to execute global control strategies based

on control and data objects in any NAC in the network, local or remote.

3. The server shall include a master clock service for its subsystems and provide time

synchronization for all Network Area Controllers (NAC).

4. The server shall accept time synchronization messages from trusted precision Atomic Clock

Internet sites and update its master clock based on this data.

5. The server shall provide scheduling for all Network Area Controllers and their underlying field

control devices.

6. The server shall provide demand limiting that operates across all Network Area Controllers. The

server must be capable of multiple demand programs for sites with multiple meters and or multiple

sources of energy. Each demand program shall be capable of supporting separate demand shed

lists for effective demand control.

7. The server shall implement the BACnet Command Prioritization scheme (16 levels) for safe and

effective contention resolution of all commands issued to Network Area Controllers. Systems not

employing this prioritization shall not be accepted.

8. Each Network Area Controller supported by the server shall have the ability to archive its log data,

alarm data and database to the server, automatically. Archiving options shall be user-defined

including archive time and archive frequency.

9. The server shall provide central alarm management for all Network Area Controllers supported by

the server. Alarm management shall include:

1. Routing of alarms to display, printer, email and pagers

2. View and acknowledge alarms

3. Query alarm logs based on user-defined parameters

10. The server shall provide central management of log data for all Network Area Controllers

supported by the server. Log data shall include process logs, runtime and event counter logs, audit

logs and error logs. Log data management shall include:

1. Viewing and printing log data

2. Exporting log data to other software applications

3. Query log data based on user-defined parameters

E. Server Hardware Requirements: The server hardware platform shall have the following requirements:

Attachment E

1. The computer shall be an Intel Pentium M based computer (minimum processing speed of 2.4

GHz with 1 GB RAM and a 100-gigabyte minimum hard drive). It shall include a DVD-

ROM/CD-RW Combination Drive, 2-parallel ports, 2-asynchronous serial ports and 2-USB ports.

A minimum 17” flat panel color monitor, 1280 x 1024 optimal preset resolution, 25 ms response

time shall also be included.

2. The server operating system shall be Microsoft Windows XP Professional. Include Microsoft

Internet Explorer 6.0 or later.

3. Connection to the FMCS network shall be via an Ethernet network interface card, 100 Mbps.

4. A system printer shall be provided. Printer shall be laser type with a minimum 600 x 600-dpi

resolution and rated for 60-PPM print speed minimum.

5. For dedicated alarm printing, provide a dot matrix printer, either 80 or 132 column width. The

printer shall have a parallel port interface.

2.13 SYSTEM PROGRAMMING

A. The Graphical User Interface software (GUI) shall provide the ability to perform system programming

and graphic display engineering as part of a complete software package. Access to the programming

functions and features of the GUI shall be through password access as assigned by the system

administrator.

B. A library of control, application, and graphic objects shall be provided to enable the creation of all

applications and user interface screens. Applications are to be created by selecting the desired control

objects from the library, dragging or pasting them on the screen, and linking them together using a built

in graphical connection tool. Completed applications may be stored in the library for future use.

Graphical User Interface screens shall be created in the same fashion. Data for the user displays is

obtained by graphically linking the user display objects to the application objects to provide “real-time”

data updates. Any real-time data value or object property may be connected to display its current value

on a user display. Systems requiring separate software tools or processes to create applications and user

interface displays shall not be acceptable.

C. Programming Methods

1. Provide the capability to copy objects from the supplied libraries, or from a user-defined library to

the user’s application. Objects shall be linked by a graphical linking scheme by dragging a link

from one object to another. Object links will support one-to-one, many-to-one, or one-to-many

relationships. Linked objects shall maintain their connections to other objects regardless of where

they are positioned on the page and shall show link identification for links to objects on other

pages for easy identification. Links will vary in color depending on the type of link; i.e., internal,

external, hardware, etc.

2. Configuration of each object will be done through the object’s property sheet using fill-in the

blank fields, list boxes, and selection buttons. Use of custom programming, scripting language, or

a manufacturer-specific procedural language for configuration will not be accepted.

3. The software shall provide the ability to view the logic in a monitor mode. When on-line, the

monitor mode shall provide the ability to view the logic in real time for easy diagnosis of the logic

execution. When off-line (debug), the monitor mode shall allow the user to set values to inputs

and monitor the logic for diagnosing execution before it is applied to the system.

4. All programming shall be done in real-time. Systems requiring the uploading, editing, and

downloading of database objects shall not be allowed.

Attachment E

5. The system shall support object duplication within a customer’s database. An application, once

configured, can be copied and pasted for easy re-use and duplication. All links, other than to the

hardware, shall be maintained during duplication.

Note to specifiers: If LonWorks devices are included as part of the project, it is necessary to provide LonWorks network management tools to manage the devices. Include Item 2.13 if LonWorks devices are included in the project.

2.14 LonWorks NETWORK MANAGEMENT

A. The Graphical User Interface software (GUI) shall provide a complete set of integrated LonWorks

network management tools for working with LonWorks networks. These tools shall manage a database

for all LonWorks devices by type and revision, and shall provide a software mechanism for identifying

each device on the network. These tools shall also be capable of defining network data connections

between LonWorks devices, known as “binding”. Systems requiring the use of third party LonWorks

network management tools shall not be accepted.

B. Network management shall include the following services: device identification, device installation,

device configuration, device diagnostics, device maintenance and network variable binding.

C. The network configuration tool shall also provide diagnostics to identify devices on the network, to reset

devices, and to view health and status counters within devices.

D. These tools shall provide the ability to “learn” an existing LonWorks network, regardless of what

network management tool(s) were used to install the existing network, so that existing LonWorks

devices and newly added devices are part of a single network management database.

E. The network management database shall be resident in the Network Area Controller (NAC), ensuring

that anyone with proper authorization has access to the network management database at all times.

Systems employing network management databases that are not resident, at all times, within the control

system, shall not be accepted.

2.15 OBJECT LIBRARIES

A. A standard library of objects shall be included for development and setup of application logic, user

interface displays, system services, and communication networks.

B. The objects in this library shall be capable of being copied and pasted into the user’s database and shall

be organized according to their function. In addition, the user shall have the capability to group objects

created in their application and store the new instances of these objects in a user-defined library.

C. In addition to the standard libraries specified here, the supplier of the system shall maintain an on-line

accessible (over the Internet) library, available to all registered users to provide new or updated objects

and applications as they are developed.

D. All control objects shall conform to the control objects specified in the BACnet specification.

E. The library shall include applications or objects for the following functions, at a minimum:

1. Scheduling Object. The schedule must conform to the schedule object as defined in the BACnet

specification, providing 7-day plus holiday & temporary scheduling features and a minimum of 10

on/off events per day. Data entry to be by graphical sliders to speed creation and selection of on-

off events.

2. Calendar Object. . The calendar must conform to the calendar object as defined in the BACnet

specification, providing 12-month calendar features to allow for holiday or special event data

Attachment E

entry. Data entry to be by graphical “point-and-click” selection. This object must be “linkable” to

any or all scheduling objects for effective event control.

3. Duty Cycling Object. Provide a universal duty cycle object to allow repetitive on/off time control

of equipment as an energy conserving measure. Any number of these objects may be created to

control equipment at varying intervals

4. Temperature Override Object. Provide a temperature override object that is capable of overriding

equipment turned off by other energy saving programs (scheduling, duty cycling etc.) to maintain

occupant comfort or for equipment freeze protection.

5. Start-Stop Time Optimization Object. Provide a start-stop time optimization object to provide the

capability of starting equipment just early enough to bring space conditions to desired conditions

by the scheduled occupancy time. Also, allow equipment to be stopped before the scheduled un-

occupancy time just far enough ahead to take advantage of the building’s “flywheel” effect for

energy savings. Provide automatic tuning of all start / stop time object properties based on the

previous day’s performance.

6. Demand Limiting Object. Provide a comprehensive demand-limiting object that is capable of

controlling demand for any selected energy utility (electric, oil, and gas). The object shall provide

the capability of monitoring a demand value and predicting (by use of a sliding window prediction

algorithm) the demand at the end of the user defined interval period (1-60 minutes). This object

shall also accommodate a utility meter time sync pulse for fixed interval demand control. Upon a

prediction that will exceed the user defined demand limit (supply a minimum of 6 per day), the

demand limiting object shall issue shed commands to either turn off user specified loads or modify

equipment set points to effect the desired energy reduction. If the list of sheddable equipment is

not enough to reduce the demand to below the set point, a message shall be displayed on the users

screen (as an alarm) instructing the user to take manual actions to maintain the desired demand.

The shed lists are specified by the user and shall be selectable to be shed in either a fixed or

rotating order to control which equipment is shed the most often. Upon suitable reductions in

demand, the demand-limiting object shall restore the equipment that was shed in the reverse order

in which it was shed. Each sheddable object shall have a minimum and maximum shed time

property to effect both equipment protection and occupant comfort.

F. The library shall include control objects for the following functions. All control objects shall conform to

the objects as specified in the BACnet specification.

1. Analog Input Object - Minimum requirement is to comply with the BACnet standard for data

sharing. Allow high, low and failure limits to be assigned for alarming. Also, provide a time

delay filter property to prevent nuisance alarms caused by temporary excursions above or below

the user defined alarm limits.

2. Analog Output Object - Minimum requirement is to comply with the BACnet standard for data

sharing.

3. Binary Input Object - Minimum requirement is to comply with the BACnet standard for data

sharing. The user must be able to specify either input condition for alarming. This object must

also include the capability to record equipment run-time by counting the amount of time the

hardware input is in an “on” condition. The user must be able to specify either input condition as

the “on” condition.

4. Binary Output Object - Minimum requirement is to comply with the BACnet standard for data

sharing. Properties to enable minimum on and off times for equipment protection as well as

interstart delay must be provided. The BACnet Command Prioritization priority scheme shall be

incorporated to allow multiple control applications to execute commands on this object with the

Attachment E

highest priority command being invoked. Provide sixteen levels of priority as a minimum.

Systems not employing the BACnet method of contention resolution shall not be acceptable.

5. PID Control Loop Object - Minimum requirement is to comply with the BACnet standard for data

sharing. Each individual property must be adjustable as well as to be disabled to allow

proportional control only, or proportional with integral control, as well as proportional, integral

and derivative control.

6. Comparison Object - Allow a minimum of two analog objects to be compared to select either the

highest, lowest, or equality between the two linked inputs. Also, allow limits to be applied to the

output value for alarm generation.

7. Math Object - Allow a minimum of four analog objects to be tested for the minimum or

maximum, or the sum, difference, or average of linked objects. Also, allow limits to be applied to

the output value for alarm generation.

8. Custom Programming Objects - Provide a blank object template for the creation of new custom

objects to meet specific user application requirements. This object must provide a simple BASIC-

like programming language that is used to define object behavior. Provide a library of functions

including math and logic functions, string manipulation, and e-mail as a minimum. Also, provide a

comprehensive on-line debug tool to allow complete testing of the new object. Allow new objects

to be stored in the library for re-use.

9. Interlock Object - Provide an interlock object that provides a means of coordination of objects

within a piece of equipment such as an Air Handler or other similar types of equipment. An

example is to link the return fan to the supply fan such that when the supply fan is started, the

return fan object is also started automatically without the user having to issue separate commands

or to link each object to a schedule object. In addition, the control loops, damper objects, and

alarm monitoring (such as return air, supply air, and mixed air temperature objects) will be

inhibited from alarming during a user-defined period after startup to allow for stabilization. When

the air handler is stopped, the interlocked return fan is also stopped, the outside air damper is

closed, and other related objects within the air handler unit are inhibited from alarming thereby

eliminating nuisance alarms during the off period.

10. Temperature Override Object - Provide an object whose purpose is to provide the capability of

overriding a binary output to an “On” state in the event a user specified high or low limit value is

exceeded. This object is to be linked to the desired binary output object as well as to an analog

object for temperature monitoring, to cause the override to be enabled. This object will execute a

Start command at the Temperature Override level of start/stop command priority unless changed

by the user.

11. Composite Object - Provide a container object that allows a collection of objects representing an

application to be encapsulated to protect the application from tampering, or to more easily

represent large applications. This object must have the ability to allow the user to select the

appropriate parameters of the “contained” application that are represented on the graphical shell of

this container.

G. The object library shall include objects to support the integration of devices connected to the Network

Area Controller (NAC). At a minimum, provide the following as part of the standard library included

with the programming software:

1. LonMark/LonWorks devices. These devices shall include, but not be limited to, devices for

control of HVAC, lighting, access, and metering. Provide LonMark manufacturer-specific objects

to facilitate simple integration of these devices. All network variables defined in the LonMark

Attachment E

profile shall be supported. Information (type and function) regarding network variables not

defined in the LonMark profile shall be provided by the device manufacturer.

2. For devices not conforming to the LonMark standard, provide a dynamic object that can be

assigned to the device based on network variable information provided by the device

manufacturer. Device manufacturer shall provide an XIF file, resource file and documentation for

the device to facilitate device integration.

3. For BACnet devices, provide the following objects at a minimum:

a. Analog In

b. Analog Out

c. Analog Value

d. Binary

e. Binary In

f. Binary Out

g. Binary Value

h. Multi-State In

i. Multi-State Out

j. Multi-State Value

k. Schedule Export

l. Calendar Export

m. Trend Export

n. Device

4. For each BACnet object, provide the ability to assign the object a BACnet device and object

instance number.

5. For BACnet devices, provide the following support at a minimum

a. Segmentation

b. Segmented Request

c. Segmented Response

d. Application Services

e. Read Property

f. Read Property Multiple

g. Write Property

h. Write Property Multiple

i. Confirmed Event Notification

j. Unconfirmed Event Notification

k. Acknowledge Alarm

Attachment E

l. Get Alarm Summary

m. Who-has

n. I-have

o. Who-is

p. I-am

q. Subscribe COV

r. Confirmed COV notification

s. Unconfirmed COV notification

t. Media Types

u. Ethernet

v. BACnet IP Annex J

w. MSTP

x. BACnet Broadcast Management Device (BBMD) function

y. Routing

Note to specifiers: Depending on the project configuration and requirements, it may be desired to integrate data from devices that are not LonMark or BACnet. These could include industrial or plant floor devices such as PLC’s. Because of the many drivers available, a common method of providing this integration, is Dynamic Data Exchange (DDE). If this is desired, use Item 2.15.

2.16 DDE DEVICE INTEGRATION

A. The Network Area Controller shall support the integration of device data via Dynamic Data Exchange

(DDE), over the Ethernet Network. The Network Area Controller shall act as a DDE client to another

software application that functions as a DDE server.

B. Provide the required objects in the library, included with the Graphical User Interface programming

software, to support the integration of these devices into the FMCS. Objects provided shall include at a

minimum:

1. DDE Generic AI Object

2. DDE Generic AO Object

3. DDE Generic BO Object

4. DDE Generic BI Object

2.17 MODBUS SYSTEM INTEGRATION

A. The Network Area Controller shall support the integration of device data from Modbus RTU, Ascii, or

TCP control system devices. The connection to the Modbus system shall be via an RS-232, RS485, or

Ethernet IP as required by the device.

B. Provide the required objects in the library, included with the Graphical User Interface programming

software, to support the integration of the Modbus system data into the FPMS. Objects provided shall

include at a minimum:

1. Read/Write Modbus AI Registers

2. Read/Write Modbus AO Registers

Attachment E

3. Read/Write Modbus BI Registers

4. Read/Write Modbus BO Registers

C. All scheduling, alarming, logging and global supervisory control functions, of the Modbus system

devices, shall be performed by the Network Area Controller.

D. The FMCS supplier shall provide a Modbus system communications driver. The equipment system

vendor that provided the equipment utilizing Modbus shall provide documentation of the system’s

Modbus interface and shall provide factory support at no charge during system commissioning

2.18 OPC SYSTEM INTEGRATION

A. The Network Area Controller shall act as an OPC client and shall support the integration of device data

from OPC servers. The connection to the OPC server shall be Ethernet IP as required by the device.

The OPC client shall support third party OPC servers compatible with the Data Access 1.0 and 2.0

specifications.

B. Provide the required objects in the library, included with the Graphical User Interface programming

software, to support the integration of the OPC system data into the BAS. Objects provided shall

include at a minimum:

1. Read/Write OPC AI Object

2. Read/Write OPC AO Object

3. Read/Write OPC BI Object

4. Read/Write OPC BO Object

5. Read/Write OPC Date/Time Input Object

6. Read/Write OPC Date/Time Output Object

7. Read/Write OPC String Input Object

8. Read/Write OPC String Output Object

C. All scheduling, alarming, logging and global supervisory control functions, of the OPC system devices,

shall be performed by the Network Area Controller.

D. The FMCS supplier shall provide an OPC client communications driver. The equipment system vendor

that provided the equipment utilizing OPC shall provide documentation of the system’s OPC server

interface and shall provide factory support at no charge during system commissioning.

Note to specifiers: Depending on the project configuration and requirements, the customer may wish to supply their own computers (PC’s), or they may be provided as part of the specification. In addition, portable computers may be required depending on the configuration or how the customer wants to access their system. Items 2.17 and 2.18 pertain to computer requirements for the Graphical User Interface Software (GUI). If no GUI software is specified, a standard Web browser can provide the customer’s access to the system. In this case, you may use these hardware requirements, or let the customer’s Web browser requirements dictate the hardware requirements.

2.19 GRAPHICAL USER INTERFACE COMPUTER HARDWARE (DESKTOP)

A. The browser workstation shall be an Intel Pentium based computer (minimum processing speed of 2.4

Ghz with 1.0 GB RAM and a 100-gigabyte minimum hard drive). It shall include a DVD-ROM/CD-

Attachment E

RW Combination Drive, 2-parallel ports, 2-asynchronous serial ports and 2-USB ports. A minimum

17”flat panel color monitor, 1280 x 1024 optimal preset resolution, 25 ms response time, shall also be

included.

B. Connection to the FMCS network shall be via an Ethernet network interface card, 10 Mbps.

C. A system printer shall be provided. Printer shall be laser type with a minimum 600 x 600-dpi resolution

and rated for 8 PPM print speed minimum.

2.20 GRAPHICAL USER INTERFACE COMPUTER HARDWARE (LAPTOP COMPUTER)

A. The laptop computer shall consist of an Intel Pentium based laptop computer (minimum processing

speed of 2 Ghz with 1 GB RAM and a 80-gigabyte minimum hard drive). It shall include a CD-ROM

drive, a 3.5” floppy drive.

B. Connection to the FMCS network shall be via an Ethernet network interface card, 10/100 Mbps.

C. A system printer shall be provided. Printer shall be laser type with a minimum 600 x 600-dpi resolution

and rated for 60 PPM print speed minimum.

2.3 OTHER CONTROL SYSTEM HARDWARE

A. Temperature Control Air Compressor (when required): A duplex air compressor system (two

compressors mounted on one tank) shall be furnished and installed by the temperature control

contractor.

1. Air compressor system shall be sized to fit the pneumatic control system, to insure no more than

33% run time.

2. The tank shall be sized for a maximum of 6 starts per hour

3. An automatic alternator shall be connected to the motors and pressure switches, in a 'lead-lag'

manner, and shall alternate compressor operation after each on-off cycle. Alternator shall be

further connected to energize the 'lag' operation after each on-off cycle. Alternator shall be further

connected to energize the 'lag' compressor at the setting of the lower pressure switch if the "lead"

compressor fails or is disabled for service.

4. Air compressor system shall include a refrigerated air dryer sized for the capacity of the air

compressor.

5. Accessories such as filters, pressure regulators, valves, spring isolators, automatic tank drain etc.

shall also be furnished for a complete operating system.

B. Space Temperature Wall Module. Wall Module shall be Honeywell or equivalent.

1. Wall module shall have a 20K Ohm NTC thermistor temperature sensor with operating range of

45 to 99 F under a locking cover/enclosure with UL 916 listing designed for mounting on a

standard electrical switch box.

2. Space temperature sensors shall be accurate to plus or minus one F degree.

3. Where specified, space temperature sensors shall have a setpoint knob calibrated for warmer-

cooler adjustments (option: calibrated to allow plus or minus adjustments to a software

setpoint).

4. Where specified, wall module shall also have an after-hours override pushbutton and LED

override indicator.

Attachment E

5. Where specified, the wall module shall have a fan coil unit fan control switch for (auto-off-

on)(auto-off-low-med-hi) fan control. The wall module function is further specified in SECTION

III Sequence of Operation.

C. Standard Automatic Control Dampers. Dampers shall be Honeywell or equivalent. Provide all automatic

control dampers not specified to be integral with other equipment.

1. Frames shall be 5 inches wide and of no less than 16-gauge galvanized steel. Inter-blade linkage

shall be within the frame and out of the air stream.

2. Blades shall not be over 8 inches wide nor less than 16-gauge galvanized steel triple V type for

rigidity.

3. Bearings shall be acetyl, oilite, nylon or ball-bearing with ½ inch diameter plated steel shafts.

4. Dampers shall be suitable for temperature ranges of -40 to 180F.

5. All proportional control dampers shall be opposed or parallel blade type as hereinafter specified

and all two-position dampers shall be parallel blade types.

6. Dampers shall be sized to meet flow requirements of the application. The sheet metal contractor

shall furnish and install baffles to fit the damper to duct size. Baffles shall not exceed 6".

Dampers with dimensions of 24 inches and less shall be rated for 3,000 fpm velocity and shall

withstand a maximum system pressure of 5.0 in. w.c. Dampers with dimensions of 36 inches and

less shall be rated for 2,500 fpm velocity and shall withstand a maximum system pressure of 4.0

in. w.c. Dampers with dimensions of 48 inches and less shall be rated for 2,000 fpm velocity and

shall withstand a maximum system pressure of 2.5 in. wc. Damper blade width shall be no greater

than 8 inches, and dampers over 48 inches wide by 74 inches high shall be sectionalized.

7. Maximum leakage for dampers in excess of sixteen inches square shall be 30 CFM per square foot

at static pressure of 1 inch of WC. Testing and ratings to be in accordance with AMCA Standard

500.

D. Low Leakage Automatic Control Dampers. Dampers shall be Honeywell or equivalent. Provide all

automatic control dampers not specified to be integral with other equipment.

1. Frames shall be 5 inches wide and of no less than 16-gauge galvanized steel. Inter-blade linkage

shall be within the frame and out of the air stream.

2. Blades shall not be over 8 inches wide nor less than 16-gauge galvanized steel triple V type for

rigidity.

3. Bearings shall be acetyl, oilite, nylon or ball-bearing with ½ inch diameter plated steel shafts.

4. Dampers shall be suitable for temperature ranges of -40 to 180F.

5. All proportional control dampers shall be opposed or parallel blade type as hereinafter specified

and all two-position dampers shall be parallel blade types.

6. Dampers shall be sized to meet flow requirements of the application. The sheet metal contractor

shall furnish and install baffles to fit the damper to duct size. Baffles shall not exceed 6".

Dampers with dimensions of 24 inches and less shall be rated for 3,000 fpm velocity and shall

withstand a maximum system pressure of 5.0 in. w.c. Dampers with dimensions of 36 inches and

less shall be rated for 2,500 fpm velocity and shall withstand a maximum system pressure of 4.0

in. wc. Dampers with dimensions of 48 inches and less shall be rated for 2,000 fpm velocity and

shall withstand a maximum system pressure of 2.5 in. w.c.

7. Side seals shall be stainless steel of the tight-seal spring type.

Attachment E

8. Dampers shall be minimum leakage type to conserve energy and the temperature control

manufacturer shall submit leakage data for all low leakage control dampers with the temperature

control submittal.

9. Maximum leakage for low leakage dampers in excess of sixteen inches square shall be 8 CFM per

square foot at static pressure of 1 inch of WC.

10. Low leakage damper blade edges shall be fitted with replaceable, snap-on, inflatable seals to limit

damper leakage.

11. Testing and ratings shall be in accordance with AMCA Standard 500.

12. Damper blade width shall be no greater than 8 inches, and dampers over 48 inches wide by 74

inches high shall be sectionalized. Testing and ratings to be in accordance with AMCA Standard

500.

E. Round Motorized Dampers. Dampers shall be Honeywell or equivalent. Round dampers shall be

provided where specified and shall be factory mounted in a section of round duct a minimum of 12

inches long, but no less than one inch longer than the duct diameter.

1. Duct shall be sleeve type spiral duct crimped on the downstream end, 24 gage galvanized

minimum except duct over 12 inches in diameter shall be 22 gage.

2. Duct shall have an integral galvanized steel actuator mounting plate and a ½ inch zinc-coated steel

blade shaft extending a minimum of 2 inches beyond the actuator mounting plate.

3. Shaft bearings shall be flanged bronze oilite pressed into the frame.

4. The blade shall be a minimum 16 gage galvanized steel, and damper frame shall be provided with

closed-cell neoprene seals with silicone rubber bead. Damper shall be designed for a 2500 ft/min

approach velocity and a 4 inch minimum static pressure.

5. Damper shall be suitable for operation from 32 to 130F temperatures.

6. Damper and actuator combination shall be designed for leakage rates less than 13 cfm per square

foot at one inch w.c differential and 25 cfm at four inches w.c. Actuator shall have an external

declutch lever to allow manual blade positioning during equipment and power malfunctions.

F. Control Valves: (Globe Type) Valves shall be Honeywell or equivalent. Control valves shall be 2-way

or 3-way pattern as shown constructed for tight shutoff and shall operate satisfactory against system

pressures and differentials.

1. Two-position valves shall be ‘line’ size. Proportional control valves shall be sized for a maximum

pressure drop of 5.0 psi at rated flow (except as may be noted on the drawings).

2. Two-way water valves shall have equal percentage flow characteristics and three-way valves shall

have equal percentage flow characteristics straight through and linear through the bypass.

3. Provide valve position indicator on all valves. Leakage rate shall be no more than 0.05% of Cv.

4. Valves 1/2 inch through 1 1/2 inch shall be screwed pattern except where solder connections are

specified for valves 1/2 or 3/4 inches.

5. Three-way valves bypass port shall be of one size reduced Cv to preclude the need for a bypass

port balancing valve.

6. Valve and cartridge replacement tool shall be configured for maintenance or replacement without

draining the coil to prevent water spill; however, an integral isolation valve on the control valve

outlet will also be acceptable.

7. Valves shall close off against 58 psi minimum.

Attachment E

8. Two inch valves shall be “screwed” configuration and 2-1/2 inch and larger valves shall be

“flanged” configuration and ANSI-rated to withstand the pressures and temperatures encountered.

9. Valves shall have stainless-steel stems and spring loaded Teflon packaging with replaceable discs.

G. Control Valves: (Characterized Ball Valves) Valves shall be Honeywell or equivalent. Control valves

1/2 to 2 inches shall be 2-way or 3-way forged brass screwed pattern as shown constructed for tight

shutoff and shall operate satisfactory against system pressures and differentials.

1. Two-position valves shall be ‘line’ size. Proportional control valves shall be sized for a maximum

pressure drop of 5.0 psi at rated flow (except as may be noted on the drawings).

2. Two-way water valves shall have equal percentage flow characteristics and three-way valves shall

have equal percentage flow characteristics straight through and linear flow through the bypass.

3. Leakage rate shall be ANSI Class IV (no more than 0.01% of Cv).

4. Valves shall be rated for no less than 350 psig at no less than 250 degrees F.

5. Provide a removable handle to operate valves manually during actuator power loss or failure.

6. Two-way valves shall close off against 100 psi minimum, and three-way valves shall close off

against 40 psi minimum.

7. Valves shall have stainless-steel or chemically nickel-plated brass stem and throttling port.

8. Valves shall be tagged with Cv rating and model number.

H. Butterfly Control Valves: Valves shall be Honeywell or equivalent. Where specified butterfly control

valves over 2” in size shall be cast iron body type for 2-way or 3-way applications specified constructed

for tight shutoff and shall operate satisfactory against system pressures and differentials.

1. Valves shall have tapped lugs for standard flange connection, and designed for isolation and

removal of downstream piping at full rated pressure.

2. Two-position valves shall be ‘line’ size.

3. Proportional control valves shall be sized for a maximum pressure drop of 5.0 psi at rated flow

(except as may be noted on the drawings).

4. Valves shall be rated for bubble tight shutoff at no less than 150 psi.

5. Valve disc shall be aluminum bronze.

6. Valve stems shall be stainless steel, with inboard top and bottom bronze bearings, and an external

corrosion resistant top bearing to absorb actuator side thrust.

I. Duct Mount, Pipe Mount and Outside Air Temperature Sensors: Temperature sensors with an accuracy

of + 0.3° F. Temperature sensors shall be Honeywell or equivalent.

1. Outside air sensors shall include an integral sun shield.

2. Duct sensors shall have sensor approximately in center of the duct, and shall have selectable

lengths of 6, 12, and 18 inches.

3. Multipoint averaging element sensors shall be provided where specified and shall have a minimum

of one foot of sensor length for each square foot of duct area (provide multiple sensors if

necessary).

4. Pipe mount sensors shall have copper, or stainless steel separable wells.

J. Current Sensitive Switches: Solid state, split core current switch that operates when the current level

(sensed by the internal current transformer) exceeds the adjustable trip point shall be provided where

Attachment E

specified. Current switches shall include an integral LED for indication of trip condition and a current

level below trip set point.

K. Water Flow Meters: Water flow meters shall be axial turbine style flow meters which translate liquid

motion into electronic output signals proportional to the flow sensed.

1. Flow sensing turbine rotors shall be non-metallic and not impaired by magnetic drag.

2. Flow meters shall be ‘insertion’ type complete with ‘hot-tap’ isolation valves to enable sensor

removal without water supply system shutdown.

3. Accuracy shall be + 2% of actual reading from 0.4 to 20 feet per second flow velocities.

L. Low Temperature Limit Switches. Limit switches shall be Honeywell or equivalent. Safety low limit

shall be manual reset twenty foot limited fill type responsive to the coolest section of its length.

M. High Temperature Limit Switches. Limit and Safety switches shall be Honeywell or equivalent. Safety

high limit (firestats) shall be manual reset type.

N. CO2 Sensors. CO2 sensors shall be Honeywell or equivalent.

1. Carbon Dioxide sensors shall be 0-10 Vdc analog output type, with corrosion free gold-plated

non-dispersive infrared sensing, designed for duct mounting.

2. Sensor shall incorporate internal diagnostics for power, sensor, analog and output checking, and

automatic background calibration algorithm for reduced maintenance. Sensor range shall be 0-

2000 PPM with +/- 50 PPM accuracy.

O. Humidity Sensors. Humidity sensors shall be Honeywell or equivalent.

1. Duct and room sensors shall have a sensing range of 5% to 95%.

2. Duct sensors shall be provided with a sampling chamber.

3. Outdoor air humidity sensors shall have a sensing range of 20% to 95% RH. They shall

have a compensated ambient temperature range of -40°F to 170° F.

P. Enthalpy Sensors. Enthalpy sensors shall be Honeywell or equivalent. Duct mounted enthalpy sensor

shall include a temperature sensor and a humidity sensor constructed to close an electrical contact upon

a drop in enthalpy (total heat) to enable economizer modes of operation where specified.

(OPTION - C7400 – Select one) Where specified provide duct mounted sensor including solid state

temperature and humidity sensors with electronics which shall output a 4-20 ma signal input to the

controller upon a varying enthalpy (total heat) to enable economizer modes of operation when outside

air enthalpy is suitable for free cooling .

Q. Annular Pitot Tube Flow Meter. Annular pitot tube shall be averaging type differential pressure sensors

with four total head pressure ports and one static port made of austenitic stainless steel.

1. Sensor shall have an accuracy of ± .25% of full flow and a repeatability of ± .05% of measured

value.

2. Transmitter shall be electronic and shall produce a linear output of 4 to 20 mAdc corresponding to

the required flow span.

3. The transmitter shall include noninteracting zero and span adjustments.

4. Acceptable Manufacturers: Pitot Tube: Dieterich Annubar, Transmitter: Setra or Dieterich

R. Variable Frequency Drives. Variable Frequency drives shall be Honeywell or equivalent.

Attachment E

1. Variable frequency drives shall be UL listed and sized for the power and loads applied.

2. Drives shall include built-in radio frequency interference (RFI) filters and be constructed to

operate in equipment rooms and shall not be susceptible to electromagnetic disturbances typically

encountered in such environments. Similarly, the drives must not excessively disturb the

environment within which it is used.

3. All VFDs over 3 horsepower shall be provided with an AC choke.

4. VFDs shall be installed in strict conformance to the manufacturer’s installation instructions, and

shall be rated to operate over a temperature range of 14 to 104 F.

5. VFD automatic operation shall be suitable for an analog input signal compatible with the digital

controller output.

6. Each VFD shall be fan cooled and have an integral keypad and alphanumeric display unit for user

interface. The display shall indicate VFD status (RUN motor rotation, READY, STOP, ALARM,

and FAULT), and shall indicate the VFD current control source (DDC input signal, keypad, or

field bus control). In addition to the alphanumeric display, the display unit shall have three pilot

lights to annunciate when the power is on (green), when the drive is running (green, blinks when

stopping and ramping down), and when the drive was shut down due to a detected fault (red, fault

condition presented on the alphanumeric display).

7. Three types of faults shall be monitored, “FAULT” shall shut the motor down, “FAULT Auto-

reset” shall shut the motor down and try to restart it for a programmable number of tries, and

“FAULT Trip” shall shut the motor down after a FAULT Auto-reset fails to restart the motor.

Coded faults shall be automatically displayed for the following faults:

Over current

Over voltage

Earth ground

Emergency stop

System (component failure)

Under voltage

Phase missing

Heat sink under temperature

Heat sink over temperature

Motor stalled

Motor over temperature

Motor underload

Cooling fan failure

Inverter bridge over temperature

Analog input control under current

Keypad failure

Other product unique monitored conditions

8. In addition to annunciating faults, at the time of fault occurrence the VFD shall capture and make

available to the user certain system data for subsequent analysis during fault trouble shooting,

including duration of operation (days, hours, minutes, seconds),output frequency, motor current,

motor voltage, motor power, motor torque, DC voltage, unit temperature, run status, rotation

direction, and any warnings. The last 30 fault occurrences shall be retained as well as the fault data

listed in the previous sentence of each fault. New faults beyond 30 shall overwrite the oldest

faults.

Attachment E

9. The display unit keypad shall allow setting operational parameters including minimum and

maximum frequency, and acceleration and deceleration times. The display shall offer user

monitoring of frequency, unit temperature, motor speed, current, torque, power, voltage, and

temperature.

S. Actuators, General. Actuators shall be Honeywell or equivalent. All automatically controlled devices,

unless specified otherwise elsewhere, shall be provided with actuators sized to operate their appropriate

loads with sufficient reserve power to provide smooth modulating action or two-position action and

tight close-off. Valves shall be provided with actuators suitable for floating or analog signal control as

required to match the controller output. Actuators shall be power failure return type where valves or

dampers are required to fail to a safe position and where specified.

T. Non-Spring Return Low Torque Direct Coupled 35 & 70 lb-in Actuators. Actuators shall be Honeywell

or equivalent. Actuators shall be 35 (ML 6161 or ML 7161) or 70 lb-in. (ML6174 or ML 7174) with

strokes adjustable for 45, 60, or 90 degree rotation applications and designed for operation between 20

and 125 F.

1. Each actuator shall also have a minimum position adjustable rotation of 0 to 30 degrees.

2. Actuators shall be for floating or two position (ML 6161 or ML6174) control, or for 4-20 mA or

2-10Vdc (ML7161 or ML7174) input signals.

3. Analog control actuators shall have a cover mounted direct/reverse acting switch.

4. Actuator motor shall be magnetically coupled or shall have limit switch stops to disengage power

at the ends of the stroke.

5. Actuators shall be direct connected (no linkages) and provided with a manual declutch for manual

positioning.

6. Actuators shall have NEMA 1 environmental protection rating and be 24 volt and UL listed with

UL94-5V plenum requirement compliance.

7. Minimum design life of actuators shall be for 1,500,000 repositions and 35 lb-in. models shall be

designed for 50,000 open-close cycles and 70 lb-in. models shall be designed for 40,000 open-

close cycles.

8. Actuator options shall include 1) Auxiliary feedback potentiometers, 2) open-closed indicator

switches, 3) actuator timings of 90 seconds, 3 minutes, or 7 minutes, one or two auxiliary

switches, and 4) torque of 35 or 70 lb-in.

U. Non-Spring Return High Torque 177 and 300 lb-in Actuators. MN6120A, MN6134A, MN7234A

Series Actuators shall be UL listed 24 Vac in NEMA 2 enclosures designed for operation between -5

and 140 F.

1. Rotation direction shall be switch selectable.

2. Minimum design life of actuators shall be for 1,500,000 repositions and for 60,000 open-close

cycles.

3. Actuators shall be suitable for the controller output signals encountered, floating or analog, and

shall have full cycle timing of 95 seconds.

4. Actuators shall be direct connected (no linkages) and provided with a manual declutch for manual

positioning.

(Select one or more of the following descriptions required)

• Actuators shall have 300 lb-in. torque.

Attachment E

• Actuators shall have 177 lb-in. torque with adjustable stroke, 30 to 90 degrees.

• Actuators shall have 177 lb-in. torque with adjustable stroke, 30 to 90 degrees, and shall

auxiliary end switches to annunciate full open and full closed positions.

V. Spring Return Direct Coupled Actuators. Actuators shall have torque ratings of 44lb-in. (MS4105,

MS7505, MS8105), 88 lb-in. (MS4110, MS7510, MS 8110), or 175 lb-in (MS4120, MS7520, MS8120).

Actuators shall be Honeywell or equivalent. Actuators shall be modulating 90 seconds nominal timing

or two-position 45 seconds nominal timing types with strokes for 90 degree rotation applications and

designed for operation between -40 and 140 F.

1. Each torque rating group shall have optionally selected control types, floating control, 2-position

24 Vac, 2-position line voltage, or analog input which is switch selectable as 0-10Vdc, 10-0 Vdc,

2-10 Vdc, or 10-2 Vdc.

2. Actuator spring return direction (open or closed) shall be easily reversed in the field, and actuators

shall spring return in no greater than 20 seconds.

3. Actuators shall be direct connected (no linkages), and shall have integral position indication.

4. Actuators shall have NEMA 2 environmental protection rating, and UL approved and plenum

rated per UL873.

5. Minimum design life of modulating actuators shall be for 1,500,000 repositions and 60,000 spring

returns, except 2-position actuators shall be for 50,000 spring returns.

6. Each actuator shall be provided with a manual power-off positioning lever for manual positioning

during power loss or system malfunctions, including a gear-train lock to prevent spring action.

7. Upon power restoration after gear lock, normal operation shall automatically recur.

W. Fast Acting Two Position Fire & Smoke Actuators (ML4115, ML8115). Actuators shall be Honeywell

or equivalent. Fire/smoke damper actuators shall be direct connected (no linkages) two-position spring

return types with stroke for 90 degree nominal rotation applications and designed for 60,000 full stroke

cycles and normal operation between 0 and 130 F.

1. Actuators control shall be compatible with SPST control switch and with torque ratings of 30 lb-

in.

2. Actuator timing shall be 25 seconds maximum in powered instances and shall spring-return in 15

seconds.

3. Actuators shall be UL listed with UL873 plenum rating with die-cast aluminum housing with

integral junction box and conduit knockouts, and designed to operate reliably in smoke control

systems requiring UL555S ratings up to 350F.

4. The actuator shall be designed to operate for 30 minutes during a one-time excursion to 350F.

5. Actuator shall require no special cycling during long-term holding, and shall “hold” with no

audible noise at a power consumption of approximately half of the driving power.

6. Actuators shall be 24 volt (ML8115) or 120 volt (ML4115) with models for clockwise (add a B

suffix) and counter-clockwise (add an A suffix) spring return.

NOTE to specifier: ML4115 spec above is good for MSXX20F also except MSXX20 is designed for 175 lb-in torque, rated for 30,000 cycles, has 15 second open & spring return timing, and has optional end switches to annunciate when the ACTUATOR is open and closed.

Attachment E

X. Temperature Control Panels: Furnish temperature control panels of code gauge steel with locking doors

for mounting all devices as shown. Control panels shall meet all requirements of Title 24, California

Administrative Code. All electrical devices within a control panel shall be factory wired. All external

wiring shall be connected to terminal strips mounted within the panel. Provide engraved phenolic

nameplates identifying all devices mounted on the face of control panels. A complete set of ‘as-built’

control drawings (relating to the controls within that panel) shall be furnished within each control panel.

Note to specifiers: Specifications for project execution can be inserted here. Items covered should include installation, training, documentation, warranty, acceptance testing and, if desired, system commissioning.

PART 3 EXECUTION

3.1 INSTALLATION

A. All work described in this section shall be performed by system integrators or contractors that have a

successful history in the design and installation of integrated control systems. The installing office shall

have a minimum of five years of integration experience and shall provide documentation in the

submittal package verifying the company's experience.

B. Install system and materials in accordance with manufacturer’s instructions, and as detailed on the

project drawing set.

C. Drawings of the TCS and FMCS network are diagrammatic only and any apparatus not shown, but

required to make the system operative to the complete satisfaction of the Architect shall be furnished

and installed without additional cost.

D. Line and low voltage electrical connections to control equipment shown specified or shown on the

control diagrams shall be furnished and installed by this contractor in accordance with these

specifications.

E. Equipment furnished by the HVAC Contractor that is normally wired before installation shall be

furnished completely wired. Control wiring normally performed in the field will be furnished and

installed by this contractor.

3.2 WIRING

A. All electrical control wiring and power wiring to the control panels, NAC, computers and network

components shall be the responsibility of the this contractor.

B. The electrical contractor (Div. 16) shall furnish all power wiring to electrical starters and motors.

C. All wiring shall be in accordance with the Project Electrical Specifications (Division 16), the National

Electrical Code and any applicable local codes. All FMCS wiring shall be installed in the conduit types

specified in the Project Electrical Specifications (Division 16) unless otherwise allowed by the National

Electrical Code or applicable local codes. Where FMCS plenum rated cable wiring is allowed it shall be

run parallel to or at right angles to the structure, properly supported and installed in a neat and

workmanlike manner.

3.3 WARRANTY

A. Equipment, materials and workmanship incorporated into the work shall be warranted for a period of

one year from the time of system acceptance.

B. Within this period, upon notice by the Owner, any defects in the work provided under this section due to

faulty materials, methods of installation or workmanship shall be promptly (within 48 hours after receipt

of notice) repaired or replaced by this contractor at no expense to the Owner

Attachment E

3.4 WARRANTY ACCESS

A. The Owner shall grant to this contractor, reasonable access to the TCS and FMCS during the warranty

period.

B. The owner shall allow the contractor to access the TCS and FMCS from a remote location for the

purpose of diagnostics and troubleshooting, via the Internet, during the warranty period.

3.5 SOFTWARE LICENSE

A. The Owner shall be the named license holder of all software associated with any and all incremental

work on the project(s). The owner, or his appointed agent, shall determine which organizations to be

named in the “orgid” of all Niagara Framework software licenses.

B. The owner, or his appointed agent, shall be free to direct the modification of the “orgid” in any Niagara

Framework software license, regardless of supplier.

C. The owner, or his appointed agent, shall receive ownership of all job specific software configuration

documentation, data files, and application-level software developed for the project. This shall include all

custom, job specific software code and documentation for all configuration and programming that is

generated for a given project and /or configured for use within Niagara Framework (Niagara) based

controllers and/or servers and any related LAN / WAN / Intranet and Internet connected routers and

devices. Any and all required Ids and passwords for access to any component or software program shall

be provided to the owner.

3.6 ACCEPTANCE TESTING

A. Upon completion of the installation, this contractor shall load all system software and start-up the

system. This contractor shall perform all necessary calibration, testing and de-bugging and perform all

required operational checks to insure that the system is functioning in full accordance with these

specifications.

B. This contractor shall perform tests to verify proper performance of components, routines, and points.

Repeat tests until proper performance results. This testing shall include a point-by-point log to validate

100% of the input and output points of the DDC system operation.

C. Upon completion of the performance tests described above, repeat these tests, point by point as

described in the validation log above in presence of Owner's Representative, as required. Properly

schedule these tests so testing is complete at a time directed by the Owner's Representative. Do not

delay tests so as to prevent delay of occupancy permits or building occupancy.

D. System Acceptance: Satisfactory completion is when this contractor and the Division 16 contractor have

performed successfully all the required testing to show performance compliance with the requirements

of the Contract Documents to the satisfaction of the Owner’s Representative. System acceptance shall

be contingent upon completion and review of all corrected deficiencies.

3.7 OPERATOR INSTRUCTION, TRAINING

A. During system commissioning and at such time acceptable performance of the TCS and FMCS

hardware and software has been established this contractor shall provide on-site operator instruction to

the owner's operating personnel. Operator instruction shall be done during normal working hours and

shall be performed by a competent representative familiar with the system hardware, software and

accessories.

B. This contractor shall provide 40 hours of instruction to the owner's designated personnel on the

operation of the TCS and FMCS and describe its intended use with respect to the programmed functions

specified. Operator orientation of the systems shall include, but not be limited to; the overall operation

program, equipment functions (both individually and as part of the total integrated system), commands,

Attachment E

systems generation, advisories, and appropriate operator intervention required in responding to the

System's operation.

C. The training shall be in three sessions as follows:

1. Initial Training: One day session (8 hours) after system is started up and at least one week before

first acceptance test. Manual shall have been submitted at least two weeks prior to training so that

the owners' personnel can start to familiarize themselves with the system before classroom

instruction begins.

2. First Follow-Up Training: Two days (16 hours total) approximately two weeks after initial

training, and before Formal Acceptance. These sessions will deal with more advanced topics and

answer questions.

3. Warranty Follow Up: Two days (16 hours total) in no less than 4 hour increments, to be scheduled

at the request of the owner during the one year warranty period. These sessions shall cover topics

as requested by the owner such as; how to add additional points, create and gather data for trends,

graphic screen generation or modification of control routines.

D.

PART 4 SEQUENCES OF OPERATION

4.1 SUMMARY

A. This contractor shall coordinate control functions, such as scheduling and supervisory-level global

control, points list, and control sequences needed for this installation as listed below. Contractor shall

provide written documentation to archive the system operation as accepted by the owner.

Note to specifiers: This part is designed to provide a clear understanding of what points are to be provided in the user interface and what they must be able to do. For each building system to be included list the points and the actions the Graphical User Interface and/or the Web browser interface must support. Each table represents a single system. In each table, enter the name of the system, the points desired, and place an “X” in the column indicating the required functionality.

PART 5 POINT LISTS

5.1 SUMMARY

A. The points in the following table shall be accessible from the Graphical User Interface (GUI) and/or the

Web browser interface (WBI). The supplier of the IDC and IBC devices shall ensure that the points

listed in this table are accessible on their respective networks, by the Network Area Controller (NAC).

Attachment E

B. The following abbreviations apply to the point table to indicate what level of functionality must be

provided:

1. D = Display only

2. M = Modify value

3. A = Alarm

4. L = Log

5. S = Schedule

6. GC = Global supervisory control routine such as demand limiting

System

Point D M A L S GC

END OF SECTION

Attachment E

Appendix A. Sequences of Operation

Select and edit the appropriate sequences, or develop new sequences and paste them into the Sequence of Operation in

SECTION III. The following sequences should be carefully reviewed to assure that they fit the project systems and

objectives.

A. Constant Volume Air Handling Unit, 2-Stage Cooling, 2-Stage Heating, with Economizer Enabled from

Outside Air Dry Bulb Temperature.

Constant Volume HVAC Unit Controller Software. The constant volume unit controller shall be

configurable for air handlers with staged or analog heating and cooling, minimum or modulating

economizer outside or mixing damper dampers, and enthalpy or dry bulb economizer changeover.

Controller shall comply with LonMark HVAC profile #8030.

ONNORMAL

81

ECON

CONSTANT VOLUME AHU,

2-STAGE COOLING, 2-STAGE HEATING W/ ECONOMIZER

7773

SPACE

TEMPERATURE

SPACE

TEMPERATURE

SETPOINT

COOLING

OUTSIDE

AIR

RETURN

AIR

FILTER

DISCHARGE

TEMPERATURE

OFF OFF ON OFF

73

SPACE

TEMPERATURE

SETPOINT

HEATING

3 3

WALL MODULE

(SEE DESCRIPTION BELOW)

1. Fan Off. Anytime the fan is off, all system heating and cooling shall be off, and the mixing

dampers shall be positioned closed to the outside air.

2. Fan and Mode Control. System fan and heating/cooling temperature setpoints shall normally be

placed in the occupied, standby, or unoccupied mode of operation and control via a system

scheduler unique seven day schedule. Prior to scheduled occupied periods, the unoccupied

temperature setpoint shall be ramped up to the occupied setpoint over a time period proportional to

the temperature difference between the room temperature and the occupied temperature setpoint

such that at occupancy time the occupied temperature is reached. During unoccupied and standby

periods the outside air damper shall be closed and the fan shall remain off until heating or cooling

is demanded to satisfy the unoccupied and standby temperature setpoints. The standby mode of

operation is for periods of temporary vacancy such as the lunch hour, and shall use owner

determined temperature setpoints a degree or two away from the occupied comfort settings.

System shall automatically revert to the proper mode of operation after restoration of power after a

power failure. Units shall restart at a random staggered time interval after power restoration.

3. Occupant Schedule Override Control. When any room HVAC system is operating in a mode

other than OCCUPIED, each room temperature sensor wall module schedule override button shall

provide the room occupant with ability to place the system in the occupied mode of operation for

60 (180 default, user programmable) minutes by pressing the module override button. Via the

Attachment E

button, the occupant shall also have the ability to cancel the override command, or to place the

system in the unoccupied mode when operating in the occupied mode. Via the module LED, the

occupant shall have the ability to note the status of the system overrides as being in the override

mode, override unoccupied mode, continuously occupied mode via a network command, or in the

normal mode of operation (LED off).

4. Smoke Control. The operator station shall be provided with a smoke control display to allow all

fan systems, via a single command, to be placed in the off mode, the zero outside air mode, or the

pressurization mode with fully open outside air dampers.

The fan shall be shut down anytime an unsafe temperature exists at a manual reset hard-wired

firestat located as required by codes.

5. Fan Fail Alarm. Any time the fan is commanded on and the fan differential pressure switch piped

across the fan, or a fan current sensor, does not prove air flow or fan operation, a fan-failed alarm

shall be presented to the operator station. This alarm check shall be delayed upon fan start for 10

seconds (adjustable) to give the system time to prove flow prior to creating a false alarm.

6. Minimum Ventilation Control. Anytime the fan runs in the occupied mode, the outside & return air

mixing dampers shall open to the outside air to a position required to introduce the minimum

outside air required for design occupant ventilation. (Include the following sentence if desired)

Anytime the indoor air quality (IAQ) sensor detects reduced occupant air contaminants, the

minimum outside air damper position shall be reduced to 50% of the design maximum to maintain

a normal design IAQ.

7. Temperature Control, Occupied Periods. Heating control shall operate with 6 cycles per hour, and

cooling control shall operate with 4 cycles per hour unless other parameters are dictated by the

equipment manufacturer. If the scheduler commands the fan to stop during periods of electric duct

heating, the heater shall be deenergized and the fan shall continue to run for 60 seconds to dissipate

the residual heater heat prior to stopping air flow. A staging PID algorithm with heating and

cooling anticipation features shall be employed for all staging control. Upon a drop in space

temperature below the heating setpoint, the lead duct heater shall be energized, the on-time

proportional to the heating load. After the lead heater stage becomes full on, a further increase in

the heating load shall cause the lag heating stage to be cycled, the on time proportional to the

increasing load. The reverse of this shall happen on a decrease in heating load. Upon a rise in space

temperature above the cooling setpoint, the lead compressor/coil shall be energized, the on-time

proportional to the cooling load. After the lead cooling stage becomes full on, a further increase in

the cooling load shall cause the lag compressor/coil stage to be cycled, the on time proportional to

the increasing load. The reverse of this shall happen on a decrease in cooling load.

Anytime the outside air enthalpy is lower than that of indoor air of 75F and 50% humidity, the

mixing dampers shall be positioned to full outside air. Anytime both cooling compressors/coils are

off in this economizer operational mode and the space cooling load decreases, the mixing dampers

shall be modulated to prevent overcooling the space with outside air.

(Two optional paragraphs for the above paragraph if desired)

OA/RA enthalpy comparison changeover: Anytime the outside air enthalpy is lower than the

return air enthalpy, the mixing dampers shall be positioned to full outside air. Anytime both

cooling compressors/coils are off in this economizer operational mode and the space cooling load

decreases, the mixing dampers shall be modulated to prevent overcooling the space with outside

air.

Attachment E

OA dry bulb changeover: Anytime the outside air temperature is below 71 degrees, the mixing

dampers shall be positioned to full outside air. Anytime both cooling compressors/coils are off in

this economizer operational mode and the space cooling load decreases, the mixing dampers shall

be modulated to prevent overcooling the space with outside air.

If the space temperature drops or rises to either the heating or cooling unoccupied temperature

setpoint during unoccupied periods, the system shall start and operate in the heating or cooling

mode until the unoccupied temperature setpoints have been satisfied. The same operation shall

occur for the standby mode of operation where specified.

8. Discharge Low Limit. If at any time the discharge air drops below the user defined discharge air

temperature low limit, an alarm shall be issued and the mixing dampers shall be driven closed to

the outside air. As the temperature rises, the dampers shall modulate open to the minimum

ventilation position and the alarm shall clear.

9. Miscellaneous. A differential pressure switch piped across each units filter shall alarm the operator

station anytime the pressure drop signifies that the filter is dirty.

10. Wall Sensor Module. Wall temperature sensor module shall be located where shown on the plans,

and shall include the temperature sensor, the occupied/unoccupied override selection push button

with override status LED (where specified), a warmer-cooler setpoint adjustment knob (where

specified), and a jack for connecting to the LonTalk communication network. The system owner

determines the normal heating and cooling room temperature setpoints for all wall module sensors

(such as 73F & 77F). The warmer-cooler adjustment knob on the wall module shall give room

occupants the ability to vary these values by an owner determined increment, such as two degrees,

by rotating the setpoint knob. Setpoints in use when the room is unoccupied shall not be affected

by the setpoint knob.

********************************************************************

B. Constant Volume Air Handling Unit, Chilled Water Cooling, Hot Water Heating, with Economizer

Enabled from Outside Air Dry Bulb Temperature.

Constant Volume HVAC Unit Controller Software. The constant volume unit controller shall be

configurable for air handlers with staged or analog heating and cooling, minimum or modulating

economizer outside or mixing damper dampers, and enthalpy or dry bulb economizer changeover.

Controller shall comply with LonMark HVAC profile #8030.

Attachment E

ONNORMAL

81

ECON

CONSTANT VOLUME AHU,

CHILLED WATER COOLING, HOT WATER HEATING W/ ECONOMIZER

7773

SPACE

TEMPERATURE

SPACE

TEMPERATURE

SETPOINT

COOLING

OUTSIDE

AIR

RETURN

AIR

FILTER

DISCHARGE

TEMPERATURE

CHRCHSHWS

HWR

73

SPACE

TEMPERATURE

SETPOINT

HEATING

WALL MODULE

(SEE DESCRIPTION BELOW)

1. Fan Off. Anytime the fan is off, all system heating and cooling shall be off, and the mixing

dampers shall be positioned closed to the outside air. Mixing dampers shall spring-return closed to

the outside air on power failure.

2. Fan and Mode Control. System fan and heating/cooling temperature setpoints shall normally be

placed in the occupied, standby, or unoccupied mode of operation and control via a system

scheduler unique seven day schedule. Prior to scheduled occupied periods, the unoccupied

temperature setpoint shall be ramped up to the occupied setpoint over a time period proportional to

the temperature difference between the room temperature and the occupied temperature setpoint

such that at occupancy time the occupied temperature is reached. During unoccupied and standby

periods the outside air damper shall be closed and the fan shall remain off until heating or cooling

is demanded to satisfy the unoccupied and standby temperature setpoints. The standby mode of

operation is for periods of temporary vacancy such as the lunch hour, and shall use owner

determined temperature setpoints a degree or two away from the occupied comfort settings.

System shall automatically revert to the proper mode of operation after restoration of power after a

power failure. Units shall restart at a random staggered time interval after power restoration.

3. Occupant Schedule Override Control. When any room HVAC system is operating in a mode

other than OCCUPIED, each temperature sensor wall module schedule override button shall

provide the room occupant with ability to place the system in the occupied mode of operation for

60 (180 default, user programmable) minutes by pressing the module override button. Via the

button, the occupant shall also have the ability to cancel the override command, or to place the

system in the unoccupied mode when operating in the occupied mode. Via the module LED, the

occupant shall have the ability to note the status of the system overrides as being in the override

mode, override unoccupied mode, continuously occupied mode via a network command, or in the

normal mode of operation (LED off).

4. Smoke Control. The operator station shall be provided with a smoke control display to allow all

fan systems, via a single command, to be placed in the off mode, the zero outside air mode, or the

pressurization mode with fully open outside air dampers.

The fan shall be shut down anytime an unsafe temperature exists at a manual reset hard-wired

firestat located as required by codes.

Attachment E

5. Fan Fail Alarm. Any time the fan is commanded on and the fan differential pressure switch piped

across the fan does not prove air flow, a fan-failed alarm shall be presented to the operator station.

This alarm check shall be delayed upon fan start for 10 seconds (adjustable) to give the system

time to prove flow prior to creating a false alarm.

6. Minimum Ventilation Control. Anytime the fan runs in the occupied mode, the outside & return air

mixing dampers shall open to the outside air to a position required to introduce the minimum

outside air required for design occupant ventilation. (Include the following sentence if desired)

Anytime the indoor air quality (IAQ) sensor detects reduced occupant air contaminants, the

minimum outside air damper position shall be reduced to 50% of the design maximum to maintain

a normal design IAQ.

7. Temperature Control, Occupied Periods. During occupied periods of operation, separate PID

algorithms shall modulate the heating or cooling valve to maintain temperatures at the occupied

setpoints.

Anytime the outside air enthalpy is lower than that of indoor air of 75F and 50% humidity, the

mixing dampers shall be positioned to full outside air. Anytime the chilled water valve is closed in

this economizer operational mode and the space cooling load decreases, the mixing dampers shall

be modulated to prevent overcooling the space with outside air.

(Two optional paragraphs for the above paragraph if desired)

OA/RA enthalpy comparison changeover: Anytime the outside air enthalpy is lower than the

return air enthalpy, the mixing dampers shall be positioned to full outside air. Anytime the chilled

water valve is closed in this economizer operational mode and the space cooling load decreases,

the mixing dampers shall be modulated to prevent overcooling the space with outside air.

OA dry bulb changeover: Anytime the outside air temperature is below 71 degrees, the mixing

dampers shall be positioned to full outside air. Anytime the chilled water valve is closed in this

economizer operational mode and the space cooling load decreases, the mixing dampers shall be

modulated to prevent overcooling the space with outside air.

8. Temperature Control, Unoccupied Periods. If the AHU-X space temperature drops or rises to either

the heating or cooling unoccupied temperature setpoint during unoccupied periods, all fans shall

start and operate to maintain the unoccupied temperature setpoints. When the AHU-X space

temperature is satisfied, the fans shall stop. The same operation shall occur for the standby mode of

operation where specified.

9. Discharge Low Limit. If at any time the discharge air drops below the user defined discharge air

temperature low limit, an alarm shall be issued and the mixing dampers shall be driven closed to

the outside air. As the temperature rises, the dampers shall modulate open to the minimum

ventilation position and the alarm shall clear.

10. Plant Commands. Anytime any hot water valve opens, the hot water pump shall be started and the

heating plant shall be enabled. Anytime any chilled water valve opens, the chilled water pump

shall be started and the cooling plant shall be enabled.

11. Miscellaneous. A differential pressure switch piped across each units filter and shall alarm the

operator station anytime the pressure drop signifies that the filter is dirty.

Attachment E

12. Wall Sensor Module. Wall temperature sensor module shall be located where shown on the plans,

and shall include the temperature sensor, the occupied/unoccupied override selection push button

with override status LED (where specified), a warmer-cooler setpoint adjustment knob (where

specified), and a jack for connecting to the LonTalk communication network. The system owner

determines the normal heating and cooling room temperature setpoints for all wall module sensors

(such as 73F & 77F). The warmer-cooler adjustment knob on the wall module shall give room

occupants the ability to vary these values by an owner determined increment, such as two degrees,

by rotating the setpoint knob. Setpoints in use when the room is unoccupied shall not be affected

by the setpoint knob.

**************************************************************

C. Unit Ventilator, One Stage DX, Hot Water Heating, Single Speed Fan, with Economizer.

Unit Ventilator Controllers. The unit ventilator controllers shall be configurable for ASHRAE Cycles I,

II, and III; chilled water or DX cooling; hot water, steam or electric heating; economizer or fixed

minimum outside air; and face and bypass dampers. Controller shall comply with LonMark HVAC

profile #8080.

ECON

HWS

HWR

RAOA

FILTER COMPRESSOR

AUTOOFFON

ON

DISCHARGE

TEMPERATURE81

OFF

77

73

SPACE

TEMPERATURE

UNIT VENTILATOR

HOT WATER, ONE STAGE DX, SINGLE SPEED FAN

73

SPACE

TEMPERATURE

SETPOINT

HEATING

OCCUPIED

UNOCCUPIED

OCC

SPACE

TEMPERATURE

SETPOINT

COOLING

WALL MODULE

(SEE DESCRIPTION BELOW)

1. Fan Off. Anytime the fan is off, all system heating and cooling shall be off, and the mixing

dampers shall be positioned closed to the outside air. Mixing dampers shall spring-return closed to

the outside air on power failure.

2. Fan and Mode Control. System fan and heating/cooling temperature setpoints shall normally be

placed in the occupied, standby, or unoccupied mode of operation and control via a system

Attachment E

scheduler unique seven day schedule. Prior to scheduled occupied periods, the unoccupied

temperature setpoint shall be ramped up to the occupied setpoint over a time period proportional to

the temperature difference between the room temperature and the occupied temperature setpoint

such that at occupancy time the occupied temperature is reached. During unoccupied and standby

periods the outside air damper shall be closed and the fan shall remain off until heating or cooling

is demanded to satisfy the unoccupied and standby temperature setpoints. The standby mode of

operation is for periods of temporary vacancy such as the lunch hour, and shall use owner

determined temperature setpoints a degree or two away from the occupied comfort settings.

System shall automatically revert to the proper mode of operation after restoration of power after a

power failure. Units shall restart at a random staggered time interval.

3. Occupant Schedule Override Control. When any room HVAC system is operating in a mode

other than OCCUPIED, each temperature sensor wall module schedule override button shall

provide the room occupant with ability to place the system in the occupied mode of operation for

60 (180 default, user programmable) minutes by pressing the module override button. Via the

button, the occupant shall also have the ability to cancel the override command, or to place the

system in the unoccupied mode when operating in the occupied mode. Via the module LED, the

occupant shall have the ability to note the status of the system overrides as being in the override

mode, override unoccupied mode, continuously occupied mode via a network command, or in the

normal mode of operation (LED off).

4. Smoke Control. The operator station shall be provided with a smoke control display to allow all

fan systems, via a single command, to be placed in the off mode, the zero outside air mode, or the

pressurization mode with fully open outside air dampers.

5. Minimum Ventilation Control. Anytime the fan runs in the occupied mode, the outside & return air

mixing dampers shall open to the outside air to a position required to introduce the minimum

outside air required for design occupant ventilation. (Include the following sentence if desired)

Anytime the indoor air quality (IAQ) sensor detects reduced occupant air contaminants, the

minimum outside air damper position shall be reduced to 50% of the design maximum to maintain

a normal design IAQ.

6. Temperature Control. Occupied Periods. Each AHU shall have adjustable occupied, standby, and

unoccupied heating and cooling setpoints. During occupied periods of operation, separate PID

algorithms shall modulate the heating valve or cycle the compressor to maintain temperatures

within the occupied setpoints. Although adjustable, the initial compressor control shall be set for 3

cycles per hour and 5.5 minutes minimum on and off times. The cooling PID algorithm shall have

cooling anticipation to minimize temperature offset.

Anytime the outside air enthalpy is lower than that of indoor air of 75F and 50% humidity, the

mixing dampers shall be positioned to full outside air. Anytime the compressor is off in this

economizer operational mode and the space cooling load decreases, the mixing dampers shall be

modulated to prevent overcooling the space with outside air.

(Two optional paragraphs for the above paragraph if desired)

OA/RA enthalpy comparison changeover: Anytime the outside air enthalpy is lower than the

return air enthalpy, the mixing dampers shall be positioned to full outside air. Anytime the

Attachment E

compressor is off in this economizer operational mode and the space cooling load decreases, the

mixing dampers shall be modulated to prevent overcooling the space with outside air.

OA dry bulb changeover: Anytime the outside air temperature is below 71 degrees, the mixing

dampers shall be positioned to full outside air. Anytime the compressor is off in this economizer

operational mode and the space cooling load decreases, the mixing dampers shall be modulated to

prevent overcooling the space with outside air.

If the space temperature rises to the cooling unoccupied temperature setpoint during unoccupied

periods, the system shall start and operate in the cooling mode until the unoccupied temperature

setpoints have been satisfied. The outside air damper shall remain closed during unoccupied

periods of operation. The same operation shall occur for the standby modes of operation where

specified.

If the AHU-X space temperature drops to the heating unoccupied temperature setpoint during

unoccupied periods, the hot water system shall start and all fans shall start and operate to maintain

the unoccupied temperature setpoints. When the AHU-X space temperature rises, the fans shall

stop. The outside air damper shall remain closed during unoccupied periods of operation. Each unit

ventilator shall cycle its respective fans and compressors if required to maintain their respective

unoccupied cooling setpoints. The same operation shall occur for the standby modes of operation

where specified.

Anytime any hot water valve opens, the hot water pump shall be started and the heating plant shall

be enabled.

7. Where ASHRAE cycles I, II, or III are used, the discharge air temperature sensor shall prevent the

air from dropping below a user defined low limit value.

8. Wall Sensor Module. Wall temperature sensor module shall be located where shown on the plans,

and shall include the temperature sensor, the occupied/unoccupied override selection push button

with override status LED (where specified), a warmer-cooler setpoint adjustment knob (where

specified), and a jack for connecting to the LonTalk communication network. The system owner

determines the normal heating and cooling room temperature setpoints for all wall module sensors

(such as 73F & 77F). The warmer-cooler adjustment knob on the wall module shall give room

occupants the ability to vary these values by an owner determined increment, such as two degrees,

by rotating the setpoint knob. Setpoints in use when the room is unoccupied shall not be affected

by the setpoint knob.

********************************************************************

D. Fan Coil Unit, Chilled Water Cooling, Hot Water Heating, with Wall Module Fan Switch

Fan Coil Unit Controller Software. The fan coil unit controller shall be configurable for staged or

analog heating and cooling. Controller shall comply with LonMark HVAC profile #8020.

Attachment E

HWS

HWR

RA

FILTER

ON

FAN COIL UNIT

HOT WATER, CHILLED WATER

CHR

CHS

77

73

WALL MODULE

(SEE DESCRIPTION BELOW)

73

SPACE

TEMPERATURE

SETPOINT

HEATING

OCCUPIED

UNOCCUPIED

OCC

SPACE

TEMPERATURE

SETPOINT

COOLING

1. Fan On-Off. The fan coil unit shall be controlled via its wall module mounted on-off switch.

Anytime the fan is off, all system heating and cooling shall be off.

2. Fan and Mode Control. System fan and heating/cooling temperature setpoints shall normally be

placed in the occupied, standby, or unoccupied mode of operation and control via a system

scheduler unique seven day schedule. Prior to scheduled occupied periods, the unoccupied

temperature setpoint shall be ramped up to the occupied setpoint over a time period proportional to

the temperature difference between the room temperature and the occupied temperature setpoint

such that at occupancy time the occupied temperature is reached. During unoccupied and standby

periods the fan shall remain off until heating or cooling is demanded to satisfy the unoccupied and

standby temperature setpoints. The standby mode of operation is for periods of temporary vacancy

such as the lunch hour, and shall use owner determined temperature setpoints a degree or two away

from the occupied comfort settings.

System shall automatically revert to the proper mode of operation after restoration of power after a

power failure.

3. Occupant Schedule Override Control. When any room HVAC system is operating in a mode

other than OCCUPIED, each temperature sensor wall module schedule override button shall

provide the room occupant with ability to place the system in the occupied mode of operation for

60 (180 default, user programmable) minutes by pressing the module override button. Via the

button, the occupant shall also have the ability to cancel the override command, or to place the

system in the unoccupied mode when operating in the occupied mode. Via the module LED, the

occupant shall have the ability to note the status of the system overrides as being in the override

mode, override unoccupied mode, continuously occupied mode via a network command, or in the

normal mode of operation (LED off).

4. Temperature Control, Occupied Periods. During occupied periods of operation, separate PID

algorithms shall modulate the heating or cooling valve to maintain temperatures at the occupied

setpoints.

Attachment E

5. Temperature Control, Unoccupied Periods. If the FCU-X space temperature drops or rises to either

the heating or cooling unoccupied temperature setpoint during unoccupied periods, all fans shall

start and operate to maintain the unoccupied temperature setpoints. When the FCU-X space

temperature is satisfied, the fans shall stop. The same operation shall occur for the standby mode of

operation where specified.

6. Plant Commands. Anytime any hot water valve opens, the hot water pump shall be started and the

heating plant shall be enabled. Anytime any chilled water valve opens, the chilled water pump

shall be started and the cooling plant shall be enabled.

7. Wall Sensor Module. Wall temperature sensor module shall be located where shown on the plans,

and shall include the temperature sensor, the occupied/unoccupied override selection push button

with override status LED (where specified), a warmer-cooler setpoint adjustment knob (where

specified), and a jack for connecting to the LonTalk communication network. The system owner

determines the normal heating and cooling room temperature setpoints for all wall module sensors

(such as 73F & 77F). The warmer-cooler adjustment knob on the wall module shall give room

occupants the ability to vary these values by an owner determined increment, such as two degrees,

by rotating the setpoint knob. Setpoints in use when the room is unoccupied shall not be affected

by the setpoint knob. During occupied periods of operation, the fan shall be controlled by the wall

module fan switch.

**************************

E. Fan Coil Unit, Chilled Water Cooling, Hot Water Heating, with Manual Fan Coil Unit

Mounted Fan Switch.

Fan Coil Unit Controller Software. The fan coil unit controller shall be configurable for staged or

analog heating and cooling. Controller shall comply with LonMark HVAC profile #8020.

HWS

HWR

RA

FILTER

ON

FAN COIL UNIT

HOT WATER, CHILLED WATER

CHR

CHS

77

73

WALL MODULE

(SEE DESCRIPTION BELOW)

73

SPACE

TEMPERATURE

SETPOINT

HEATING

OCCUPIED

UNOCCUPIED

OCC

SPACE

TEMPERATURE

SETPOINT

COOLING

Attachment E

1. Fan On-Off. During occupied periods, the fan shall be controlled manually by the unit-mounted fan

control switch. Anytime the fan is off as detected by an air flow switch, all system heating and

cooling shall be off and valves shall close.

2. Mode Control. System heating/cooling temperature setpoints shall normally be placed in the

occupied, standby, or unoccupied mode of operation and control via a system scheduler unique

seven day schedule. Prior to scheduled occupied periods, the unoccupied temperature setpoint shall

be ramped up to the occupied setpoint over a time period proportional to the temperature difference

between the room temperature and the occupied temperature setpoint such that at occupancy time

the occupied temperature is reached. The standby mode of operation is for periods of temporary

vacancy such as the lunch hour, and shall use owner determined temperature setpoints a degree or

two away from the occupied comfort settings.

System shall automatically revert to the proper mode of operation after restoration of power after a

power failure.

3. Occupant Schedule Override Control. When any room HVAC system is operating in a mode

other than OCCUPIED, each temperature sensor wall module schedule override button shall

provide the room occupant with ability to place the system in the occupied mode of operation for

60 (180 default, user programmable) minutes by pressing the module override button. Via the

button, the occupant shall also have the ability to cancel the override command, or to place the

system in the unoccupied mode when operating in the occupied mode. Via the module LED, the

occupant shall have the ability to note the status of the system overrides as being in the override

mode, override unoccupied mode, continuously occupied mode via a network command, or in the

normal mode of operation (LED off).

4. Temperature Control, Occupied Periods. During occupied periods of operation, separate PID

algorithms shall modulate the heating or cooling valve to maintain temperatures at the occupied

setpoints.

5. Temperature Control, Unoccupied Periods. If the FCU-X space temperature drops or rises to either

the heating or cooling unoccupied temperature setpoint during unoccupied periods, all fans shall

start and operate to maintain the unoccupied temperature setpoints. When the FCU-X space

temperature is satisfied, the fans shall stop. The same operation shall occur for the standby mode of

operation where specified.

6. Plant Commands. Anytime any hot water valve opens, the hot water pump shall be started and the

heating plant shall be enabled. Anytime any chilled water valve opens, the chilled water pump shall

be started and the cooling plant shall be enabled.

8. Wall Sensor Module. Wall temperature sensor module shall be located where shown on the plans,

and shall include the temperature sensor, the occupied/unoccupied override selection push button

with override status LED (where specified), a warmer-cooler setpoint adjustment knob (where

specified), and a jack for connecting to the LonTalk communication network. The system owner

determines the normal heating and cooling room temperature setpoints for all wall module sensors

(such as 73F & 77F). The warmer-cooler adjustment knob on the wall module shall give room

occupants the ability to vary these values by an owner determined increment, such as two degrees,

by rotating the setpoint knob. Setpoints in use when the room is unoccupied shall not be affected

by the setpoint knob.

Attachment E

*******************************************************************************

F. Chilled Ceiling Unit with Hot Water Radiation

Chilled Ceiling/Hot Water Radiation Controllers. The room temperature controller shall be LonMark

based suitable for chilled water cooling and hot water, steam or electric heating. Controller shall

comply with LonMark HVAC profile # 8020.

CHILLED CEILING

HOT WATER RADIATION

CHR

CHS

61

HWS

HWR

77

73

SPACE

TEMPERATURE

73

SPACE

TEMPERATURE

SETPOINT

HEATING

OCCUPIED

UNOCCUPIED

OCC

SPACE

TEMPERATURE

SETPOINT

COOLING

WALL MODULE

(SEE DESCRIPTION BELOW)

1. Room Mode Control. System heating/cooling temperature setpoints shall normally be placed in the

occupied, standby, or unoccupied mode of operation and control via a system scheduler unique

seven day schedule. Prior to scheduled occupied periods, the unoccupied temperature setpoint shall

be ramped up to the occupied setpoint over a time period proportional to the temperature difference

between the room temperature and the occupied temperature setpoint such that at occupancy time

the occupied temperature is reached. The standby mode of operation is for periods of temporary

vacancy such as the lunch hour, and shall use owner determined temperature setpoints a degree or

two away from the occupied comfort settings.

System shall automatically revert to the proper mode of operation after restoration of power after a

power failure.

2. Occupant Schedule Override Control. When any room system is operating in a mode other

than OCCUPIED, each specified temperature sensor wall module schedule override button shall

Attachment E

provide the room occupant with ability to place the system in the occupied mode of operation for

60 (180 default, user programmable) minutes by pressing the module override button. Via the

button, the occupant shall also have the ability to cancel the override command, or to place the

system in the unoccupied mode when operating in the occupied mode. Via the module LED, the

occupant shall have the ability to note the status of the system overrides as being in the override

mode, override unoccupied mode, continuously occupied mode via a network command, or in the

normal mode of operation (LED off).

3. Temperature Control, Occupied Periods. During occupied periods of operation, separate PID

algorithms shall modulate the heating or cooling valve to maintain temperatures at the occupied

setpoints.

4. Temperature Control, Unoccupied Periods. If the ROOM-X space temperature drops or rises to

either the heating or cooling unoccupied temperature setpoint during unoccupied periods, the

appropriate heating or cooling plant shall start and operate to maintain the unoccupied temperature

setpoints. When the ROOM-X space temperature is satisfied, plant shall stop. The same operation

shall occur for the standby mode of operation where specified.

5. Wall Controller Module. Wall temperature sensor module shall be located where shown on the

plans, and shall include the room controller, the temperature sensor, the occupied/unoccupied

override selection push button with override status LED where specified, a warmer-cooler setpoint

adjustment knob where specified, and a jack for connecting to the LonWorks communication

network. The system owner determines the normal heating and cooling room temperature setpoints

for all wall module sensors (such as 73F & 77F). The warmer-cooler adjustment knob on the wall

module shall give room occupants the ability to vary these values by an owner determined

increment, such as two degrees, by rotating the setpoint knob. Setpoints in use when the room is

unoccupied shall not be affected by the setpoint knob.

6. Dewpoint Control. If at any time the ceiling panel chilled water temperature drops below the owner

determined panel dewpoint temperature, an alarm shall be issued to the operator station and all

ceiling panel valves shall close until the chilled water temperature recovers.

**********************

G. VAV Box, Cooling Only, Pressure Independent

VAV Box Software. The VAV box controller shall be LonMark based suitable pressure dependent and

pressure independent control. Controller shall comply with LonMark HVAC profile # 8010.

VAV BOX

AIR

FLOW

77

73

SPACE

TEMPERATURE

OCCUPIED

UNOCCUPIED

OCC

SPACE

TEMPERATURE

SETPOINT

COOLING

WALL MODULE

(SEE DESCRIPTION BELOW)

Attachment E

1. Temperature Control. Zone temperature cooling setpoint shall normally be placed in the occupied,

standby, or unoccupied mode of operation and control via a system scheduler unique seven day

schedule. Prior to scheduled occupied periods, the unoccupied temperature setpoint shall be

ramped down to the occupied setpoint over a time period proportional to the temperature

difference between the room temperature and the occupied temperature setpoint such that at

occupancy time the occupied temperature is reached. During unoccupied and standby periods the

unoccupied and standby temperature setpoints shall be maintained. The standby mode of operation

is for periods of temporary vacancy such as the lunch hour, and shall use owner determined

temperature setpoints a degree or two away from the occupied comfort settings.

VAV box controls shall be enabled anytime the respective VAV AHU fan operates. Each VAV

box shall have unique design minimum and maximum primary air cfm setpoints. As the cooling

load varies a PID algorithm shall reset the box cfm setpoint between these min and max values to

maintain the setpoint. An AIA algorithm shall modulate the box damper to maintain the cfm

setpoint.

The BMCS operator shall have displays of the space temperature, the primary air cfm, and the box

damper position. The operator shall have displays and modification ability of the three temperature

setpoints and the two cfm setpoints.

2. Occupant Schedule Override Control. When any room HVAC system is operating in a mode

other than OCCUPIED, each temperature sensor wall module shall provide the room occupant

with ability to place the system in the occupied mode of operation for 60 (180 default, user

programmable) minutes by pressing the wall module override button. Via the button, the occupant

shall also have the ability to cancel the override command, or to place the system in the

unoccupied mode when operating in the occupied mode. Via the module LED, the occupant shall

have the ability to note the status of the system overrides as being in the override mode, override

unoccupied mode, continuously occupied mode via a network command, or in the normal mode of

operation (LED off).

3. Wall Sensor Module. Wall temperature sensor module shall be located where shown on the plans,

and shall include the temperature sensor, the occupied/unoccupied override selection push button

with override status LED (where specified), a warmer-cooler setpoint adjustment knob (where

specified), and a jack for connecting to the LonWorks communication network (Except for Low

Cost models). The system owner determines the normal heating and cooling room temperature

setpoints for all wall module sensors (such as 73F & 77F). The warmer-cooler adjustment knob on

the wall module shall give room occupants the ability to vary these values by an owner determined

increment, such as two degrees, by rotating the setpoint knob. Setpoints in use when the room is

unoccupied shall not be affected by the setpoint knob.

*******************************

H. VAV Box, Cooling & 2-Stage Heat, Pressure Independent

Attachment E

VAV Box Software. The VAV box controller shall be LonMark based suitable pressure dependent and

pressure independent control and staged electric heat. Controller shall comply with LonMark HVAC

profile # 8010.

3 3

VAV BOX - 2 STAGE HEAT

AIR

FLOW

77

73

SPACE

TEMPERATURE

73

SPACE

TEMPERATURE

SETPOINT

HEATING

OCCUPIED

UNOCCUPIED

OCC

SPACE

TEMPERATURE

SETPOINT

COOLING

WALL MODULE

(SEE DESCRIPTION BELOW)

1. Temperature Control. Zone temperature setpoints shall normally be placed in the occupied,

standby, or unoccupied mode of operation and control via a system scheduler unique seven day

schedule. Prior to scheduled occupied periods, the unoccupied temperature setpoint shall be

ramped up or down to the occupied setpoint over a time period proportional to the temperature

difference between the room temperature and the occupied temperature setpoint such that at

occupancy time the occupied temperature is reached. During unoccupied and standby periods the

unoccupied and standby heating and cooling temperature setpoints shall be maintained. The

standby mode of operation is for periods of temporary vacancy such as the lunch hour, and shall

use owner determined temperature setpoints a degree or two away from the occupied comfort

settings.

VAV box controls shall be enabled anytime the respective VAV AHU fan operates. Each VAV

box shall have unique design minimum, reheat, and maximum primary air cfm setpoints. As the

cooling load varies a PID algorithm shall reset the box cfm setpoint between these min and max

values to maintain the cooling setpoint. An AIA algorithm shall modulate the box damper to

maintain the cfm setpoint. (An AIA is an adaptive algorithm designed specially for the application)

As the zone temperature drops to the heating setpoint, the box shall maintain the reheat cfm

setpoint and cycle the duct heaters to maintain the setpoint. The heating algorithm shall be PID

with anticipation characteristics to minimize room temperature overshoot.

The BMCS operator shall have displays of the space temperature, the primary air cfm, the box

damper position, and the duct heater status’. The operator shall have displays and modification

ability of the six temperature setpoints and the three cfm setpoints.

2. Occupant Schedule Override Control. When any room HVAC system is operating in a mode

other than OCCUPIED, each temperature sensor wall module shall provide the room occupant

with ability to place the system in the occupied mode of operation for 60 (180 default, user

programmable) minutes by pressing the wall module override button. Via the button, the occupant

shall also have the ability to cancel the override command, or to place the system in the

unoccupied mode when operating in the occupied mode. Via the module LED, the occupant shall

have the ability to note the status of the system overrides as being in the override mode, override

Attachment E

unoccupied mode, continuously occupied mode via a network command, or in the normal mode of

operation (LED off).

3. Wall Sensor Module. Wall temperature sensor module shall be located where shown on the plans,

and shall include the temperature sensor, the occupied/unoccupied override selection push button

with override status LED (where specified), a warmer-cooler setpoint adjustment knob (where

specified), and a jack for connecting to the LonWorks communication network (Except for Low

Cost models). The system owner determines the normal heating and cooling room temperature

setpoints for all wall module sensors (such as 73F & 77F). The warmer-cooler adjustment knob on

the wall module shall give room occupants the ability to vary these values by an owner determined

increment, such as two degrees, by rotating the setpoint knob. Setpoints in use when the room is

unoccupied shall not be affected by the setpoint knob.

***********************************************************

I. VAV Box, Cooling & Hot Water Heat, Pressure Independent

VAV Box Software. The VAV box controller shall be LonMark based suitable pressure dependent and

pressure independent control with modulating heating and cooling. Controller shall comply with

LonMark HVAC profile # 8010.

HWS

HWR

VAV BOX - HOT WATER HEAT

AIR

FLOW

77

73

SPACE

TEMPERATURE

73

SPACE

TEMPERATURE

SETPOINT

HEATING

OCCUPIED

UNOCCUPIED

OCC

SPACE

TEMPERATURE

SETPOINT

COOLING

WALL MODULE

(SEE DESCRIPTION BELOW)

1. Temperature Control. Zone temperature setpoints shall normally be placed in the occupied,

standby, or unoccupied mode of operation and control via a system scheduler unique seven day

schedule. Prior to scheduled occupied periods, the unoccupied temperature setpoint shall be

ramped up or down to the occupied setpoint over a time period proportional to the temperature

difference between the room temperature and the occupied temperature setpoint such that at

occupancy time the occupied temperature is reached. During unoccupied and standby periods the

unoccupied and standby heating and cooling temperature setpoints shall be maintained. The

standby mode of operation is for periods of temporary vacancy such as the lunch hour, and shall

use owner determined temperature setpoints a degree or two away from the occupied comfort

settings.

VAV box controls shall be enabled anytime the respective VAV AHU fan operates. Each VAV

box shall have unique design minimum and maximum primary air cfm setpoints. As the cooling

load varies a PID algorithm shall reset the box cfm setpoint between these min and max values to

Attachment E

maintain the setpoint. An AIA algorithm shall modulate the box damper to maintain the cfm

setpoint.

As the zone temperature drops to the heating setpoint, the box shall maintain the minimum cfm

setpoint and modulate the hot water valve via a PID algorithm to maintain the heating setpoint.

The BMCS operator shall have displays of the space temperature, the primary air cfm, the box

damper position, and the hot water valve position. The operator shall have displays and

modification ability of the six temperature setpoints and the two cfm setpoints.

2. Occupant Schedule Override Control. When any room HVAC system is operating in a mode

other than OCCUPIED, each temperature sensor wall module shall provide the room occupant

with ability to place the system in the occupied mode of operation for 60 (180 default, user

programmable) minutes by pressing the wall module override button. Via the button, the occupant

shall also have the ability to cancel the override command, or to place the system in the

unoccupied mode when operating in the occupied mode. Via the module LED, the occupant shall

have the ability to note the status of the system overrides as being in the override mode, override

unoccupied mode, continuously occupied mode via a network command, or in the normal mode of

operation (LED off).

3. Wall Sensor Module. Wall temperature sensor module shall be located where shown on the plans,

and shall include the temperature sensor, the occupied/unoccupied override selection push button

with override status LED (where specified), a warmer-cooler setpoint adjustment knob (where

specified), and a jack for connecting to the LonWorks communication network (Except for Low

Cost models). The system owner determines the normal heating and cooling room temperature

setpoints for all wall module sensors (such as 73F & 77F). The warmer-cooler adjustment knob on

the wall module shall give room occupants the ability to vary these values by an owner determined

increment, such as two degrees, by rotating the setpoint knob. Setpoints in use when the room is

unoccupied shall not be affected by the setpoint knob.

PART 6

********************************************************************

J. VAV Box, Cooling and Hot Water Heat, Parallel Fan, & Pressure Independent

VAV Box Software. The VAV box controller shall be LonMark based suitable pressure dependent and

pressure independent control, hot water heat, and parallel fan. Controller shall comply with LonMark

HVAC profile # 8010.

Attachment E

AIR

FLOW

HWS

HWR

77

73

SPACE

TEMPERATURE

73

SPACE

TEMPERATURE

SETPOINT

HEATING

OCCUPIED

UNOCCUPIED

OCC

SPACE

TEMPERATURE

SETPOINT

COOLING

VAV BOX - HOT WATER HEAT

PARALLEL FAN

WALL MODULE

(SEE DESCRIPTION BELOW)

1. Temperature Control. Zone temperature setpoints shall normally be placed in the occupied,

standby, or unoccupied mode of operation and control via a system scheduler unique seven day

schedule. Prior to scheduled occupied periods, the unoccupied temperature setpoint shall be

ramped up or down to the occupied setpoint over a time period proportional to the temperature

difference between the room temperature and the occupied temperature setpoint such that at

occupancy time the occupied temperature is reached. During unoccupied and standby periods the

unoccupied and standby heating and cooling temperature setpoints shall be maintained. The

standby mode of operation is for periods of temporary vacancy such as the lunch hour, and shall

use owner determined temperature setpoints a degree or two away from the occupied comfort

settings.

VAV box controls shall be enabled anytime the respective VAV AHU fan operates. Each VAV

box shall have unique design minimum and maximum primary air cfm setpoints. As the cooling

load varies a PID algorithm shall reset the box cfm setpoint between these min and max values to

maintain the setpoint. An AIA algorithm shall modulate the box damper to maintain the cfm

setpoint.

As the zone temperature drops to the heating setpoint, the box shall maintain the minimum cfm

setpoint for the primary air and start the parallel fan for the first stage of heating with the warm

plenum air. As the heating load increases, the hot water valve shall be modulated open via a PID

algorithm to maintain the heating setpoint.

The BMCS operator shall have displays of the space temperature, the primary air cfm, the box

damper position, the parallel fan status, and the hot water valve position. The operator shall have

displays and modification ability of the six temperature setpoints and the two cfm setpoints.

2. Occupant Schedule Override Control. When any room HVAC system is operating in a mode

other than OCCUPIED, each temperature sensor wall module shall provide the room occupant

with ability to place the system in the occupied mode of operation for 60 (180 default, user

programmable) minutes by pressing the wall module override button. Via the button, the occupant

shall also have the ability to cancel the override command, or to place the system in the

unoccupied mode when operating in the occupied mode. Via the module LED, the occupant shall

have the ability to note the status of the system overrides as being in the override mode, override

unoccupied mode, continuously occupied mode via a network command, or in the normal mode of

operation (LED off).

Attachment E

3. Wall Sensor Module. Wall temperature sensor module shall be located where shown on the plans,

and shall include the temperature sensor, the occupied/unoccupied override selection push button

with override status LED (where specified), a warmer-cooler setpoint adjustment knob (where

specified), and a jack for connecting to the LonWorks communication network (Except for Low

Cost models). The system owner determines the normal heating and cooling room temperature

setpoints for all wall module sensors (such as 73F & 77F). The warmer-cooler adjustment knob on

the wall module shall give room occupants the ability to vary these values by an owner determined

increment, such as two degrees, by rotating the setpoint knob. Setpoints in use when the room is

unoccupied shall not be affected by the setpoint knob.

PART 7

********************************************************

K. VAV Box, Cooling, Hot Water Heat, Series Fan, Pressure Independent

VAV Box Software. The VAV box controller shall be LonMark based suitable pressure dependent and

pressure independent control with hot water heat and series fan. Controller shall comply with LonMark

HVAC profile # 8010.

77

73

SPACE

TEMPERATURE

73

SPACE

TEMPERATURE

SETPOINT

HEATING

OCCUPIED

UNOCCUPIED

OCC

SPACE

TEMPERATURE

SETPOINT

COOLING

VAV BOX - HOT WATER HEAT

SERIES FAN

AIR

FLOW

HWS

HWR

WALL MODULE

(SEE DESCRIPTION BELOW)

1. Temperature Control. Zone temperature setpoints shall normally be placed in the occupied,

standby, or unoccupied mode of operation and control via a system scheduler unique seven day

schedule. Prior to scheduled occupied periods, the unoccupied temperature setpoint shall be

ramped up or down to the occupied setpoint over a time period proportional to the temperature

difference between the room temperature and the occupied temperature setpoint such that at

occupancy time the occupied temperature is reached. During unoccupied and standby periods the

unoccupied and standby heating and cooling temperature setpoints shall be maintained. The

standby mode of operation is for periods of temporary vacancy such as the lunch hour, and shall

use owner determined temperature setpoints a degree or two away from the occupied comfort

settings.

VAV box controls shall be enabled anytime the respective VAV AHU fan operates. Each VAV

box shall have unique design minimum and maximum primary air cfm setpoints. As the cooling

load varies a PID algorithm shall reset the box cfm setpoint between these min and max values to

maintain the setpoint. An AIA algorithm shall modulate the box damper to maintain the cfm

setpoint.

Attachment E

As the zone temperature drops to the heating setpoint, the box shall maintain the minimum cfm

setpoint for the primary air and the hot water valve shall be modulated open via a PID algorithm to

maintain the heating setpoint.

The BMCS operator shall have displays of the space temperature, the primary air cfm, the box

damper position, the series fan status, and the hot water valve position. The operator shall have

displays and modification ability of the six temperature setpoints and the two cfm setpoints.

2. Occupant Schedule Override Control. When any room HVAC system is operating in a mode

other than OCCUPIED, each temperature sensor wall module shall provide the room occupant

with ability to place the system in the occupied mode of operation for 60 (180 default, user

programmable) minutes by pressing the wall module override button. Via the button, the occupant

shall also have the ability to cancel the override command, or to place the system in the

unoccupied mode when operating in the occupied mode. Via the module LED, the occupant shall

have the ability to note the status of the system overrides as being in the override mode, override

unoccupied mode, continuously occupied mode via a network command, or in the normal mode of

operation (LED off).

3. Wall Sensor Module. Wall temperature sensor module shall be located where shown on the plans,

and shall include the temperature sensor, the occupied/unoccupied override selection push button

with override status LED (where specified), a warmer-cooler setpoint adjustment knob (where

specified), and a jack for connecting to the LonWorks communication network (Except for Low

Cost models). The system owner determines the normal heating and cooling room temperature

setpoints for all wall module sensors (such as 73F & 77F). The warmer-cooler adjustment knob on

the wall module shall give room occupants the ability to vary these values by an owner determined

increment, such as two degrees, by rotating the setpoint knob. Setpoints in use when the room is

unoccupied shall not be affected by the setpoint knob.

********************************

Optional Paragraphs: If analog filter monitoring is desired, substitute all filter switch sequences

with the following: A differential pressure sensor shall be piped across each units filter. When

assigned dirty filter analog alarm limits are exceeded, the operator station shall be alarmed.

If freezestat fan shutdown is required for water system protection, add the following: Anytime

the mixed air temperature drops below the limited fill low temperature limit switch, the fan shall

stop and the mixing dampers shall close fully to the outside air.

If demand control is desired, insert the following paragraph: Demand Limit Control (DLC). The

system shall monitor the building electrical power demand and control specified electrical loads in

three categories, off continuous, rotating loads off, and last resort loads.

Off continuous loads shall be shut down for the excessive demand duration, and restored after the

excess is over.

Rotating loads shall be provided with unique minimum and maximum demand reduction times,

and minimum on-times. In addition to shedding electrical loads, comfort control setpoints shall be

assignable to the DLC program shall be assignable to be “bumped” up or down a specified

temperature value to reduce heating and cooling energy. The setpoint shall be immediately bumped

for energy reduction, but at the end of the demand reduction cycle, the setpoint restoration shall be

Attachment E

slowly ramped back to the comfort settings over a time period to prevent bumping back into the

high demand state.

The DLC program shall also maintain an Energy History Log for the previous 35 days including

the energy consumed (kWh), the peak load (kW), time of peak load, and the degree days.