REMOVING AND INSTALLING DFI HIGH-PRESSURE PUMP · - Never use compressed air when the system is...

8/23/18, 12(19 PMRemoving And Installing DFI High-Pressure Pump (Fuel Pump) - ALLDATA Repair

of 20https://my.alldata.com/repair/#/repair/article/46613/component/20/itype/401/nonstandard/1320687/selfRefLink/false

2008 Porsche Cayenne S (9PA) V8-4.8LVehicle > Powertrain Management > Fuel Delivery and Air Induction > Fuel Pump > Service and Repair > Removaland Replacement

REMOVING AND INSTALLING DFI HIGH-PRESSURE PUMP

Removing And Installing DFI High-pressure Pump

Tools

Technical values



Preliminary work

INFORMATION Before replacing the high-pressure pump if you suspect that it is faulty, check the performance ofthe fuel pumps in the tank. - 200201 Checking fuel pressure (low pressure) on DFI engines or - 206601 Checkingfuel delivery rate (low pressure delivery rate) on DFI engines

1. Remove engine compartment cover at the plenum panel at the middle and left. 2. Move bonnet into service position. 3. Remove cover of plenum panel. 4. Pull out the fuses for the two fuel pumps. This stops the fuel pumps from starting up when a door is opened.

https://my.alldata.com/repair/#/repair/vehicle/46613/component/20/filter/




5. Remove plenum panel wall on the left. 5.1.Release oxygen sensor connector from the bracket on the plenum panel wall -1-. Unclip cable. -2-. 5.2.Release PDCC reservoir from plenum panel, if fitted. 5.3.Unscrew three screws on the plenum panel. -3-. 5.4.Pull plenum panel up and off.

INFORMATION:

Component overview




Removing high-pressure pump

DANGER: Danger of poisoning from fuels.

- Gasoline is toxic. - Inhaling vapours can cause irritation of the mucous membranes and eyes. - It can be carcinogenic. It represents a serious risk to health when inhaled, touched or swallowed over longerperiods. - Only work on the fuel system in well-ventilated rooms. - Wear protective gloves that are fuel-resistant.





- Wear protective gloves that are fuel-resistant. - Wear a breathing mask with active charcoal filter; do not breathe in any fuel vapours. - Ensure that there is adequate ventilation and extract all fuel vapours. - Before opening the fuel lines or fuel hoses, relieve the fuel pressure. - Collect escaping fuel, absorb it if necessary with a suitable binding material and dispose of properly. - Pay attention to cleanliness when working on the fuel system.

DANGER: Danger of fire from fuel.

- Keep clear of ignition sources. - Do not smoke. - Disconnect battery. - Danger of fire due to naked flames and sparks, e.g. during welding or grinding work. - Danger of fire due to escaping fuel, e.g. on hot engine components or due to electrostatic charge. Allow engineto cool down. - Secure the vehicle, e.g. with a warning sign. - Change any clothing soaked with fuel immediately. - In case of fire, use CO2 or dry powder fire extinguishers.

CAUTION: Dirt on injection system components (intake manifold injection and direct ) - Material damage - Rough-running engine - Bad exhaust emissions

fuel injection system

- Thoroughly clean connection points and adjacent areas before loosening them. If the engine is very dirty, washit before starting disassembly work. - Lay removed parts on a clean surface and cover them. Do not use fibre-shedding cloths. - Carefully cover components or seal them if repair work will not be carried out immediately. Place rubber capson connections. Seal intake openings with film or adhesive tape. - Only install clean parts. Do not take spare parts out of the packaging until just before installation. - Never use compressed air when the system is open. Do not move the vehicle.

CAUTION: Danger of fire from leaking high-pressure lines. - Fuel can leak out if high-pressure lines are bent or damaged. - Fuel can leak out if threaded joints are not fitted correctly. - Fuel can leak out if the tightening specifications are not observed.

- Never bend high-pressure lines. - The high-pressure distribution pipe (rail) or other fuel feed components in the high-pressure area must alwaysbe completely removed. - Perform a visual inspection to ensure that connection points are undamaged and perfectly clean. - Check that threaded joints at connection points are not seized up or corroded. Make sure the thread is not







- Check that threaded joints at connection points are not seized up or corroded. Make sure the thread is notdamaged. - Fit union nuts on all connection points by hand before screwing in screws or bolts. - Pay attention to cleanliness. Remove dirt on the ball/conical joints. - Check or inspect connection points for leaks following assembly.

INFORMATION: - Absorb any escaping fuel using a suitable binding material or a cloth. - Cloths which have absorbed fuel must be disposed of according to the applicable national laws. - The fuel system must be depressurised before starting work on it. - Only work on the fuel system in well-ventilated rooms. - Any seals which have been removed must always be replaced. - Do not use any sealant containing silicone or silicone spray when the injection system is open. Traces ofsilicone drawn in by the engine are not combusted and damage the oxygen sensors. - Following replacement of the high-pressure pump and engine, the values for the high-pressure adaptationmust be reset using the PIWIS Tester. Then carry out a test and adaptation drive. Read the information in thesection.

1. Remove low-pressure line for high-pressure pump at fuel line transfer point -1-. Place cloths underneath.Counter with an open-ended wrench when doing this. Low-pressure line remains attached to the high-pressurepump.



2. Disconnect cable for fuel temperature sensor -1- and unclip cable. -2-.



3. Remove crash panel for high-pressure pump. Very confined work area between high-pressure pump andplenum panel. For this reason, unscrew the three screws at the crash panel -arrows- using a straight ring wrenchand remove with your fingertips. Turbo: The ATL vent line is secured under one screw.



4. Undo high-pressure line at union nut on high-pressure pump. 5. Turbo: Pull out wire harness at the plenum panel and lay it to one side. Pull off cable plug for hall sender.

6. Remove both hexagon-head union nuts -2 and 3- and the fastening screw -1- for the high-pressure pump. 7. Carefully pull high-pressure pump out of cylinder head.



7.1.To do this, you will need to overcome the resistance of the sealing ring. Carefully lever off high-pressurepump with a screwdriver Removing high-pressure pump. Remove high-pressure pump by twisting it betweencylinder head and plenum panel.



7.2.Turn high-pressure pump slightly, pull off cable plug for flow control valve. -arrow-.

7.3.The Oldham coupling between the inlet camshaft and high-pressure pump remains in the camshaftbecause of a loss preventer -1-. Oldham coupling has symmetrical chamfers for the drivers on the high-pressurepump. -2-.

8. In order to replace the high-pressure pump, the low-pressure line that is still fitted must be unscrewed. Whenre-installing the pump, the low-pressure line must be at a distance of 5 to 8 mm from the high-pressure line.

Installing high-pressure pump

DANGER: Danger of poisoning from fuels.

- Gasoline is toxic. - Inhaling vapours can cause irritation of the mucous membranes and eyes. - It can be carcinogenic. It represents a serious risk to health when inhaled, touched or swallowed over longerperiods. - Only work on the fuel system in well-ventilated rooms. Wear protective gloves that are fuel-resistant. - Wear a breathing mask with active charcoal filter; do not breathe in any fuel vapours. - Ensure that there is adequate ventilation and extract all fuel vapours.



- Ensure that there is adequate ventilation and extract all fuel vapours. - Before opening the fuel lines or fuel hoses, relieve the fuel pressure. - Collect escaping fuel, absorb it if necessary with a suitable binding material and dispose of properly. - Pay attention to cleanliness when working on the fuel system.

DANGER: Danger of fire from fuel.

- Keep clear of ignition sources. - Do not smoke. - Disconnect battery. - Danger of fire due to naked flames and sparks, e.g. during welding or grinding work. - Danger of fire due to escaping fuel, e.g. on hot engine components or due to electrostatic charge. Allow engineto cool down. - Secure the vehicle, e.g. with a warning sign. - Change any clothing soaked with fuel immediately. - In case of fire, use CO2 or dry powder fire extinguishers.

CAUTION: Dirt on injection system components (intake manifold injection and direct system) - Material damage - Rough-running engine - Bad exhaust emissions

fuel injection

- Thoroughly clean connection points and adjacent areas before loosening them. If the engine is very dirty, washit before starting disassembly work. - Lay removed parts on a clean surface and cover them. Do not use fibre-shedding cloths. - Carefully cover components or seal them if repair work will not be carried out immediately. Place rubber capson connections. Seal intake openings with film or adhesive tape. - Only install clean parts. Do not take spare parts out of the packaging until just before installation. - Never use compressed air when the system is open. Do not move the vehicle.

CAUTION: Danger of fire from leaking high-pressure lines. - Fuel can leak out if high-pressure lines are bent or damaged. - Fuel can leak out if threaded joints are not fitted correctly. - Fuel can leak out if the tightening specifications are not observed.

- Never bend high-pressure lines. - The high-pressure distribution pipe (rail) or other fuel feed components in the high-pressure area must alwaysbe completely removed. - Perform a visual inspection to ensure that connection points are undamaged and perfectly clean. - Check that threaded joints at connection points are not seized up or corroded. Make sure the thread is notdamaged.





damaged. - Fit union nuts on all connection points by hand before screwing in screws or bolts. - Pay attention to cleanliness. Remove dirt on the ball/conical joints. - Check or inspect connection points for leaks following assembly.

INFORMATION: - Absorb any escaping fuel using a suitable binding material or a cloth. - Cloths which have absorbed fuel must be disposed of according to the applicable national laws. - The fuel system must be depressurised before starting work on it. - Only work on the fuel system in well-ventilated rooms. - Any seals which have been removed must always be replaced. - Do not use any sealant containing silicone or silicone spray when the injection system is open. Traces siliconedrawn in by the engine are not combusted and damage the oxygen sensors. - Following replacement of the high-pressure pump and engine, the values for the high-pressure adaptationmust be reset using the PIWIS Tester. Then carry out a test and adaptation drive. Read the information in thesection.

If the fitting in the high-pressure pump is loosened accidentally, tighten it to Tightening torque: 35 Nm (26 ftlb.).When re-installing the low-pressure line on the high-pressure pump, the distance from the high-pressure line mustbe set to at least 5 to 8 mm.

1. When re-installing a used high-pressure pump, check the drive coupling and Oldham coupling - using a mirror -for signs of wear. 2. Using a mirror, check the position of the Oldham coupling of the inlet camshaft and turn the drive coupling forthe high-pressure pump to the correct installation position by hand.



the high-pressure pump to the correct installation position by hand.

INFORMATION: 000 043 204 68 (Status 02/07) Kluber Syntheso GLEP 1 is a neutral-reaction assembly greasethat can be used for connection pieces and sealing rings in oily or water-carrying areas.

3. Replace sealing ring on high-pressure pump and grease using Kluber Syntheso GLEP 1.

4. When installing the high-pressure pump, connect the cable plug for the flow control valve. -arrow-.



5. Install high-pressure pump while turning it and position screw and union nut -1, 2 and 3-. When installed, theconnecting elements are very difficult to access using a torque wrench. Careful tightening by hand is acceptable. - Tightening torque: 10 Nm (7.5 ftlb.)

6. Loosen eyelet on cylinder side 5 to 8 and fold to the side -2-. Eyelet prevents the torque wrench from engaging. 7. Using the leak test equipment, blow the fuel out of the high-pressure pump.



7. Using the leak test equipment, blow the fuel out of the high-pressure pump.

8. Fit high-pressure line to the adapter for the high-pressure pump. Allow a gap of 5 to 8 mm to the low-pressureline. Tighten high-pressure line in three stages. Open-ended socket ring wrench Nr.185 and torque wrench mustbe used. - Tightening torque: 25 Nm (19 ftlb.), then loosen, - Tightening torque: 25 Nm (19 ftlb.)

9. Perform leak test on high-pressure pump.



10. Connect cable plug for temperature sensor -1-. Clip in cable. -2-.

11. Fit low-pressure line on adapter for fuel line according to the marking. Counter at the fuel line -1-. - Tightening torque: 35 Nm (26 ftlb.)



12. Fit crash panel for high-pressure pump. Very confined work area between high-pressure pump and plenumpanel. For this reason, position the three screws on the crash panel using your fingertips and fit using a straightring wrench -arrows-. Turbo: The ATL vent line is secured under one screw. - Tightening torque: 10 Nm (7.5 ftlb.)

13. Turbo: Fit wire harness to plenum panel. Connect cable plug to hall sender.

14. Tighten eyelet. - Tightening torque: 23 Nm (17 ftlb.)

Subsequent work



1. Fit plenum panel wall on the left. 1.1.Pre-fit seal for plenum panel on vehicle-side part of bulkhead and spray with silicone spray. 1.2.Press in plenum panel until the screw positions are seated correctly. 1.3.Fit three screws for the plenum panel. -3-. - Tightening torque: 9 Nm (6.5 ftlb.) 1.4.Fit oxygen sensor connector to plenum panel wall. Clip in cable. -1 and 2-. 1.5.Secure PDCC reservoir to the plenum panel, if this reservoir is to be fitted.

2. Fit cover for plenum panel. 3. Fit engine compartment cover at the plenum panel at the middle and left. 4. Dismantle service position of bonnet. 5. Fit the fuses for the two fuel pumps.

INFORMATION: Bleed the high-pressure system. - Following disassembly work and a subsequent leak test on the high-pressure system, there will be air and gascushions in the system. - The bleeding process may take several minutes. - Faults entries may be recorded in the engine control unit during the bleeding process. The engine switches toemergency operating mode. - Erase the fault memory of the DME control unit repeatedly if necessary and bleed the system several times. - The bleeding process is complete when the engine runs smoothly at idle speed and takes in gas in the correctmanner. - A test drive must then be carried out and the fault memory must be read out.

6. Bleed the fuel high-pressure system.

INFORMATION: Following replacement of the high-pressure pump and engine, the values for the high-pressureadaptation must be reset using the PIWIS Tester. Then carry out a test and adaptation drive. Read theinformation in the section.






information in the section.

REMOVING AND INSTALLING DFI HIGH-PRESSURE PUMP · - Never use compressed air when the system is...

Documents

Transcript of REMOVING AND INSTALLING DFI HIGH-PRESSURE PUMP · - Never use compressed air when the system is...