Relining a steelbore_with_stainless_spiral_tube_2003

Bore Casing & Screens Pipes & Components Environmental Drilling Water Treatment Safety Products Sand Spears Pumps

Case Study

Ph 1300 133 000

Relining a Steel BoreWith

Stainless Spiral Tube

The Problem


Case Study Relining a Steel Borewith Stainless Spiral Tube

Ph 1300 133 000

Your old steel borecasing is corroding away. It has been in the ground for 10-30 years and now it is pumping sand as the casing has corroded away leaving holes for the sand aquifer to fall into the bore.


Case Study Relining a Steel Borewith Stainless Spiral Tube

Ph 1300 133 000

this will destroy the pump and can fill the bore with sand type materials until eventually no water will flow through, and the pump will be stuck in the bore and unable to be removed.Water is needed sooner than later to keep the grassed paddock alive.

Requirements


Case Study

Ph 1300 133 000

To fit inside corroded steel casing OD of Casing to fit past where corrosion has taken place.Allowing the original pump to fit inside the installed casing.Non CorrosivePump the same amount of water as originally

Relining a Steel Borewith Stainless Spiral Tube


Case Study

Ph 1300 133 000

To withstand the Installation depth.Flush on OD for installation and gravel pack if neededStrong Integral strengthJoin to the original Borescreen


Solution


Case Study

Ph 1300 133 000

The solution is to reline your bore with spiral welded tube manufactured to allow the maximum opening of the borecasing.

It would be beneficial to have a camera sent down the bore to see where the hole is and at what depth and how the screen is joined to the casing.



Case Study

Ph 1300 133 000

Run a piece of steel down the inside of the casing to check that the new relining casing will slide down to the correct depth.


Deps Answer


Case Study

Ph 1300 133 000

To supply stainless steel spiral welded tube, designed and made specially to maximise the inside diameter of the casing used to reline the old bore.

The material’s wall thickness can be changed to suit the depth of the bore, in this case it was 2mm thick 304 stainless steel.



Case Study

Ph 1300 133 000

This has a bursting pressure of approx 1400 Psi and a collapse pressure of 7280 Psi, with this pressure and only a depth setting of 30M this casing will withstand what is required.


Alternatives


Case Study

Ph 1300 133 000

Other Alternatives where to use fibreglass casing, this has to be imported or manufactured, with a lead time of over 6 weeks.

Stainless steel tubing and pipe could be used, but the sizes are limited to standard sizes available.



Case Study

Ph 1300 133 000

PVC pipe could be used but again it is limited to standard sizing thus the original pump would not fit into this bore and a new smaller pump would have to be purchased, this would not deliver the quantity of water needed.

Drill a new bore at great expense


The End Result


Case Study

Ph 1300 133 000

The specialized stainless tube casing was delivered on time and successfully installed by the driller. The bore hole was commissioned by the driller and the original pump was installed successfully.When developed the bore delivered the original quantity of water as it always had.


Thank you for taking the time to look at the information we have created for you,We hope this will be of assistance to solving your piping, drainage and drilling challenges.

If you have any more questionsPlease feel free to contact myself or one of our team


Article Relining a Steel Borewith Stainless Spiral Tube


For more Articles, Case Studies, How to and Information

go to www.deps.com.authen click onto Handy Links

or contact us on1300 133 000

[email protected]

Case Study

Ph 1300 133 000

SlottingCuttingFabricatingPipe TestingPerforationDrawingsSpear PointsSafetyPumpsBore Casing & Screens Pipes & Components Environmental Drilling Water Treatment

Safety Products Sand Spears Pumps

Deps Products and Capabilities

ThreadingTurningWeldingSlitting

DesigningWater

TreatmentPipe

Drilling products

Pipe FittingsPh 1300 133

000

Relining a steelbore_with_stainless_spiral_tube_2003

Education

Transcript of Relining a steelbore_with_stainless_spiral_tube_2003