Relay Setting p120
2
MiCOM S1 Studio Page: 1 Settings File Report File: 000.set Model Number: P120Bxxxxxx V11 Printed on: 09/03/2013 14:08:42 - Settings File Report - : OP PARAMETERS: 0000: Type:P120-1 010A: Reference:ALST 0005: Version software:11.C 0104: Frequency:50Hz : CONFIGURATION: : CT RATIO: 0122: CT Primary:5 0123: CT Sec:5 : LED 5: 0150: LED 5:0000001010000000 0154: LED 5 part 2:0000000000000000 : LED 6: 0151: LED 6:0000000001000000 0155: LED 6 part 2:0000000000000000 : LED 7: 0152: LED 7:0000000001000000 0156: LED 7 part 2:0000000000000000 : LED 8: 0153: LED 8:0000000001000000 0157: LED 8 part 2:0000000000000000 : OUTPUT RELAYS: 012E: Fail Safe Relays:0000000000000000 : ALARM: 0600: Inhibited t Aux alarms:0000000000000000 : PROTECTION: : [50/51] PHASE OC AND [50N/51N] E/Gnd: 0230: Function I>:Yes 0231: I>:0.1In 0232: Delay Type:IDMT 0233: Idmt:SI (IEC) 0234: TMS:0.1 0240: Function I>>:Yes 0241: I>>:0.3In 0242: tI>>:0s 0250: Function I>>>:No : AUTOMAT. CTRL: : TRIP COMMANDS: 0180: Trip:0000000000011000 : LATCHFUNCTIONS: 0181: Latch:0000000000000000 : BLOCKINGLOGIC: 0182: Block:0000000000000000 : OUTPUTRELAYS:
-
Upload
najmul-islam -
Category
Documents
-
view
216 -
download
0
Transcript of Relay Setting p120
7/29/2019 Relay Setting p120
http://slidepdf.com/reader/full/relay-setting-p120 1/2
MiCOM S1 Studio Page: 1
Settings File Report
File: 000.set
Model Number: P120Bxxxxxx V11 Printed on: 09/03/2013 14:08:42
- Settings File Report -
: OP PARAMETERS:0000: Type:P120-1
010A: Reference:ALST
0005: Version software:11.C
0104: Frequency:50Hz
: CONFIGURATION:
: CT RATIO:0122: CT Primary:5
0123: CT Sec:5
: LED 5:0150: LED 5:0000001010000000
0154: LED 5 part 2:0000000000000000
: LED 6:0151: LED 6:0000000001000000
0155: LED 6 part 2:0000000000000000
: LED 7:0152: LED 7:0000000001000000
0156: LED 7 part 2:0000000000000000
: LED 8:0153: LED 8:0000000001000000
0157: LED 8 part 2:0000000000000000
: OUTPUT RELAYS:012E: Fail Safe Relays:0000000000000000
: ALARM:0600: Inhibited t Aux alarms:0000000000000000
: PROTECTION:: [50/51] PHASE OC AND [50N/51N] E/Gnd:
0230: Function I>:Yes
0231: I>:0.1In
0232: Delay Type:IDMT
0233: Idmt:SI (IEC)
0234: TMS:0.1
0240: Function I>>:Yes
0241: I>>:0.3In
0242: tI>>:0s
0250: Function I>>>:No
: AUTOMAT. CTRL:
:TRIPCOMMANDS:
0180: Trip:0000000000011000
: LATCHFUNCTIONS:
0181: Latch:0000000000000000
:BLOCKINGLOGIC:
0182: Block:0000000000000000
:OUTPUTRELAYS:
7/29/2019 Relay Setting p120
http://slidepdf.com/reader/full/relay-setting-p120 2/2
MiCOM S1 Studio Page: 2
Settings File Report
File: 000.set
Model Number: P120Bxxxxxx V11 Printed on: 09/03/2013 14:08:42
- Settings File Report -
0171: Trip:00000110017B: I>:00000000
0175: tI>:00000000
017C: I>>:00000000
0176: tI>>:00000000
017D: I>>>:00000000
0177: tI>>>:00000000
016B: CB CLOSE:00000000
0620: Input 1:00000000
0621: Input 2:00000000
016C: tAux1:00000000
016D: tAux2:00000000
: INPUTS:
0160: Input 1:0000000000000010
015B: Input 1:0000000000000000
0161: Input 2:0000000000000100
015C: Input 2:0000000000000000
019B: tAux1:0s
019C: tAux2:0s
: RECORD:
:FAULTRECORD:
010C: Fault Number:25
:OCEFSTART:
010E: Record Number:5
:DISTURBRECORD:
0190: Pré-Time:0.1s0191: Post_Time:0.1s
0192: Disturb Rec Trig:ON INST.
