REFERENCES - Shodhgangashodhganga.inflibnet.ac.in/bitstream/10603/10212/20/20_references.pdf ·...
Transcript of REFERENCES - Shodhgangashodhganga.inflibnet.ac.in/bitstream/10603/10212/20/20_references.pdf ·...
References
386
REFERENCES
1. Ahmaniemi, S., Rajamaki, E., Vuoristo, P. and Mantyla, T., (2000), “Effect of
aluminum phosphate sealing treatment on properties of thick thermal barrier
coatings”, in: C.C. Berndt (Ed.), Proceedings of 1st ITSC’2000, ASM
International, Materials Park, OH, USA, pp. 1081-1085.
2. Ahmaniemi, S., Tuominen, J., Vuoristo, P. and Mantyla, T., (2002A), “Sealing
Procedures for Thick Thermal Barrier Coatings,” J. Therm. Spray Technol., Vol.
11, No. 3, pp. 320-332.
3. Ahmaniemi, S., Vuoristo, P. and Mantyla, T., (2002B), “Improved sealing
treatments for thick thermal barrier coatings,” Surf. Coat. Technol., Vol. 151-152,
pp. 412-417.
4. ASM Specialty Handbook, (1997), “Heat Resistant Materials,” Edited by J.R.
Davis, ASM Publication, Metals Park OH, USA.
5. Bala, N., Singh, H. and Prakash, S., (2007), “An Overview of Characterisations
and High Temperature Behaviour of Thermal Spray NiCr Coatings,” Int. J. Mater.
Sci., Vol. 2, No. 3, pp. 201-218.
6. Bala, N., Singh, H., and Prakash, S., (2009A), “High Temperature Corrosion
Behavior of Cold Spray Ni-20Cr Coating on Boiler Steel in Molten Salt
Environment at 900 ºC,” J. Therm. Spray Technol., Vol. 19, pp. 110-118.
7. Bala, N., Singh, H. and Prakash, S., (2009B), “High Temperature Oxidation
Studies of Cold Sprayed Ni-20Cr and Ni-50Cr Coatings on SAE 213-T22 Boiler
Steel,” Appl. Surf. Sci., Vol. 255, No. 15, pp. 6862-6869.
8. Bala, N., Singh, H. and Prakash, S., (2009C), “Accelerated Hot Corrosion Studies
of Cold Spray Ni-50Cr Coating on Boiler Steels,” Mater. Design, Vol. 31, pp.
244-253.
9. Bala, N., (2010), “Investigations on the hot corrosion behaviour of cold spray and
HVOF spray coatings on T22 and SA 516 steels,” Ph.D. Thesis, Mechanical
Engineering, Punjab Technical University, Jalandhar (Punjab), India.
387
10. Bolelli, G., Cannillo, V., Lusvarghi, L., Montorsi, M., Mantini, F.P. and Barletta,
M., (2007), “Microstructural and tribological comparison of HVOF-sprayed and
post-treated M–Mo–Cr–Si (M = Co, Ni) alloy coatings,” Wear, Vol. 263, pp.
1397-1416.
11. Bolelli, G. and Lusvarghi, L., (2008), “Heat treatment effects on the corrosion
resistance of some HVOF-sprayed metal alloy coatings,” Surf. Coat. Technol.,
Vol. 202, pp. 4839-4847.
12. Bornstein, N.S., DeCrescente, M.A. and Roth, H.A., (1975), “Effect of
Vanadium and Sodium Compounds on the Accelerated Oxidation of Nickel Base
Alloys,” Proc. of Conf. on Gas Turbine Mater. in the Marine Environment,
MMIC-75-27, Columbus, Ohio USA, pp. 115-160.
13. Bray, M., Cockburn, A. and O'Neill, W., (2009), “The Laser-assisted Cold Spray
process and deposit characterization,” Surf. Coat. Technol., Vol. 203, pp 2851-
2857.
14. Calvarin, G., Molins, R. and Huntz, A.M., (2000), “Oxidation Mechanism of Ni-
20Cr Foils and Its Relation to the Oxide-Scale Microstructure,” Oxid. Met., Vol.
53, No. 1-2, pp. 25-48.
15. Celik, E., Demirkıran, A.S. and Avci, E., (1999), “Effect of grit blasting of
substrate on the corrosion behaviour of plasma-sprayed Al2O3 coatings,” Surf.
Coat. Technol., Vol. 116-119, pp. 1061-1064.
16. Celik, E., Ozdemir, I., Avci, E. and Tsunekawa, Y., (2005), “Corrosion behaviour
of plasma sprayed coatings,” Surf. Coat. Technol., Vol. 193, pp. 297-302.
17. Chandler, P.E. and Quigley, M.B.C., (1986), Proc. 11th Int. Thermal Spraying
Conf., Montreal, Canada, 8-12 September, 1986, p. 29.
18. Changqing, X., Xiaomin, P. and Jia, L., (2008), “Behavior of NiCrAlY coating
on the TC6 titanium alloy,” Journal of University of Science and Technoiogy
Belling, Vol. 15, No. 2, pp. 167-170.
19. Chatha, S.S., Sidhu, H.S. and Sidhu, B.S., (2011) “Role of Post Treatment in
Thermal Spray Coatings,” Int. J. of Mater. Sci. Eng., Vol. 2, No. 1-2, pp.153-162.
20. Chatha, S.S., Sidhu, H.S. and Sidhu, B.S., (2012A), “High temperature hot
corrosion behaviour of NiCr and Cr3C2-NiCr coatings on T91 boiler steel in an
References
388
aggressive environment at 750 °C,” Surf. Coat. Technol., Vol. 206, No. 19-20, pp.
3839-3850.
21. Chatha, S.S., Sidhu, H.S. and Sidhu, B.S., (2012B), “The effects of post-
treatment on the hot corrosion behaviour of the HVOF sprayed Cr3C2-NiCr
coating,” Surf. Coat. Technol., Vol. 206, No. 19-20, pp. 4212-4224.
22. Chatterjee, U.K., Bose, S.K. and Roy, S.K., (2001), ‘Environmental Degradation
of Metals,’ Pub. Marcel Dekker, 270 Madison Avenue, New York.
23. Chen, D., Jordan, E.H. and Gell, M., (2009), “Solution precursor high-velocity
oxy-fuel spray ceramic coatings,” J. European Ceramic Society, Vol. 29, pp.
3349-3353.
24. Ctibor, P., Neufuss, K., Zahalka, F. and Kolman, B., (2007), “Plasma sprayed
ceramic coatings without and with epoxy resin sealing treatment and their wear
resistance,” Wear, Vol. 262, pp. 1274-1280.
25. Cvijovic, I., Jovanovic, M.T. and Perusko, D., (2008), “Cyclic oxidation
behaviour of Ti3Al-based alloy with Ni–Cr protective layer,” Corros. Sci., Vol.
50, pp. 1919-1925.
26. Danyluk, S. and Park, J.Y., (1979), “Technical Note: Corrosion and Grain
Boundary Penetration in Type 316 Stainless Steel Exposed to a Coal Gasification
Environment,” Corrosion, Vol. 35, No. 12, pp. 575-576.
27. Das, D., Balasubramaniam, R. and Mungole, M.N., (2002A), “Hot corrosion of
Fe3Al,” J. Mater. Sci., Vol. 37, No. 6, pp.1135-1142.
28. Das, D., Balasubramaniam, R. and Mungole, M.N., (2002B), “Hot Corrosion of
Carbon-Alloyed Fe3Al-based Iron Aluminides,” Mater. Sci. Eng. A, Vol. 338, pp.
24-32.
29. Davis, J.R. and Associates, (2004), “Handbook of Thermal Spray Technology,”
ASM International, Thermal Spray Society Training Committee.
30. Dent, A.H., Horlock, A.J., McCartney, D.G. and Harris, S.J., (2001),
“Microstructural Characterisation of a Ni-Cr-B-C Based Alloy Coating Produced
by High Velocity Oxy-Fuel Thermal Spraying,” Surf. Coat. Technol., Vol. 139,
pp. 244-250.
389
31. Dragos, U., Gabriela, M., Waltraut, B. and Ioan, C., (2005), “Improvement of the
oxidation behaviour of electron beam remelted MCrAlY coatings,” Solid State
Sci., Vol. 7, pp. 459-464.
32. Evans, H. E. and Taylor, M. P., (2001), “Diffusion Cells and Chemical Failure of
MCrAlY Bond Coats in Thermal-Barrier Coating Systems,” Oxid. Met., Vol. 55,
No. 1-2, pp. 17-34.
33. Fagoaga, I., Viviente, J.L., Gavin, P., Bronte, J.M., Garcia, J. and Tagle, J.A.,
(1998), “Multilayer Coatings by Continuous Detonation System Spray
Technique,” Thin Solid Films, Vol. 317, pp. 259-265.
34. Fantassi, S., Vardelle, M., Fauchais, P. and Moreau, C., (1992), “Investigation of
the Splat Formation versus Different Particulate Temperatures and Velocities
Prior to Impact,” Proc. of 13th
Int. Thermal Spray Conf., Florida, USA, pp. 755-
760.
35. Fernandez, E., Garcıa, J.R., Cuetos, J.M. and Higuera, V., (2005), “Behaviour of
laser treated Cr, Ni coatings in the oxidative atmosphere of a steam boiler,” Surf.
Coat. Technol., Vol. 195, pp. 1-7.
36. Greving, D.J., Rybicki, E.F. and Shadley, J.R., (1994), "Through-Thickness
Residual Stress Evaluations for Several Industrial Thermal Spray Coatings Using
a Modified Layer Removal Method," J. Therm. Spray Technol., Vol. 3, No. 4, pp
379-388.
37. Guilemany, J.M., Fernandez, J., Delgado, J., Benedetti, A. V. and Climent, F.,
(2002A), “Effects of Thickness Coatings on the Electrochemical Behavior of
Thermal Spray Cr3C2-NiCr Coatings,” Surf. Coat. Technol., Vol. 153, No. 2-3,
pp. 107-113.
38. Guilemany, J.M., Miguel, J.M., Vizcaino, S., Lorenzana, C., Delgado, J. and
Sanchez, J., (2002B), “Role of heat treatments in the improvement of the sliding
wear properties of Cr3C2–NiCr coatings,” Surf. Coat. Technol., Vol. 157, pp. 207-
213.
39. Guilemany, J.M., Torrell, M. and Miguel, J.R., (2008), “Study of the HVOF Ni-
Based Coatings’Corrosion Resistance Applied on Municipal Solid-Waste
Incinerators,” J. Therm. Spray Technol., Vol. 17, No. 2, pp. 254-262.
References
390
40. Hancock, P. and Hurst R.C., (1974), “The Mechanical Properties and Breakdown
of Surface Oxide Films at Elevated Temperatures,” in ‘Advances in Corros. Sci.
and Technol.,’ Vol. 4, Eds. Fontana, M.G. and Staehle, R.W., Pub. Plenum Press,
New York.
41. He, J. and Lavernia, E.J., (2001A), “Thermal Stability of Nanostructured Cr3C2-
NiCr Coatings.” J. Therm. Spray Technol., Vol. 10, No. 2. pp. 293-300.
42. He, J. and Lavernia, E.J., (2001B), “Precipitation Phenomenon in Nanostructured
Cr3C2-NiCr Coatings,” Mater. Sci. Eng. A, Vol. 301, pp. 69-79.
43. Herman, H., Sampath, S. and Mccune, R., (2000), “Thermal Spray: Current
Status and Future Trends,” MRS Bull, Vol. 25, No. 7, pp. 17-25.
44. Hidalgo, V.H., Varela, J.B., Calle, J.M. and Menendez, A.C., (2000),
“Characterisation of NiCr Flame and Plasma Sprayed Coatings for Use in High
Temperature Regions of Boilers,” Surf. Eng., Vol. 16, No. 2, pp. 137-142.
45. Hidalgo, V.H., Varela, F.J.B., Menendez, A.C. and Martinez, S.P., (2001A), “A
Comparative Study of High-temperature Erosion Wear of Plasma-sprayed
NiCrBSiFe and WC-NiCrBSiFe Coatings under Simulated Coal-fired Boiler
Conditions,” Tribol., Vol. 34, pp. 161-169.
46. Hidalgo, V.H., Varela, J.B., Menendez, A.C. and Martinez, S.P., (2001B), “High
Temperature Erosion Wear of Flames and Plasma-sprayed Nickel-chromium
Coatings under Coal-fired Boiler Atmospheres,” Wear, Vol. 247, pp. 214-222.
47. Holt, A. and Kofstad, P., (1989), “High Temperature Corrosion of Iron in O2 +
4% SO2/SO3 at 500-800 °C," Mater. Sci. Engg. A, Vol. A120, pp. 101-04.
48. Huminik, J., (1963), “High-Temperature Inorganic Coatings,” Reinhold Pub.
Corp., New York.
49. Huttunen, S.E., Stott, F.H., Rohr, V. and Schutze, M., (2007), “Erosion–
oxidation behaviour of pack-aluminized 9% chromium steel under fluidized-bed
conditions at elevated temperature,” Corros. Sci., Vol. 49, pp. 2844-2865.
50. Iyer, S.R., Iyer, K.J.L. and Radhakrishan, V.M., (1987), “Proc. of 10th ICMC,”
Madras, India IV, p. 3665.
391
51. Jacobs, L., Hyland, M.M., Bonte, M.D., (1998), “Comparative Study of WC-
Cermet Coatings Sprayed via the HVOF and the HVAF Process,” Therm. Spray
Technol.,” Vol. 7, No.2, pp. 213-218.
52. JasimKadhim, M., (2009), “Laser sealing and thermal shock resistance of 6.5
wt% yttria Partially stabilized zirconia plasma sprayed layers,” Eng. & Tech.
Journal, Vol. 27, No. 6, pp. 1038-1045.
53. Kai, T., Xiang-lin, Z., Hua, C. and Ji-shan, Z., (2009), “Oxidation and hot
corrosion behaviors of HVAF-sprayed conventional and nanostructured NiCrC
coatings,” Trans. Nonferrous Met. Soc., China, Vol. 19, pp. 1151-1160.
54. Kamal, S. Jayaganthan, R., Prakash, S. and Kumar, S., (2008), “Hot Corrosion
Behavior of Detonation Gun Sprayed Cr3C2-NiCr Coatings on Ni and Fe-based
Superalloys in Na2SO4-60%V2O5 Environment at 900 °C,” J. Alloys Compd.,
Vol. 463, No. 1-2, pp. 358-372.
55. Kamal, S. Jayaganthan, R., Prakash, S. and Kumar, S., (2009A), “Evaluation of
cyclic hot corrosion behaviour of detonation gun sprayed Cr3C2-25%NiCr
coatings on nickel- and iron-based superalloys,” Surf. Coat. Technol., Vol. 203,
pp. 1004-1013.
56. Kamal, S., Jayaganthan, R. and Prakash, S., (2009B), “High temperature
oxidation studies of detonation-gun-sprayed Cr3C2–NiCr coating on Fe- and Ni-
based superalloys in air under cyclic condition at 900 °C,” J. Alloys Compd., Vol.
472, pp. 378-389.
57. Kamal, S., Jayaganthan, R., Prakash, S. and Kumar, S., (2010), “Mechanical and
microstructural characteristics of detonation gun sprayed NiCrAlY + 0.4 wt%
CeO2 coatings on superalloys,” Mater. Chem. Phys., Vol. 122, No. 1, pp 262-268.
58. Kaplin, C. and Brochu, M., (2011), “Effects of water vapor on high temperature
oxidation of cryomilled NiCoCrAlY coatings in air and low-SO2 environments,”
Surf. Coat. Technol., Vol. 205, pp. 4221-4227.
59. Kaur, M., Singh, H. and Prakash, S., (2011), “Surface engineering analysis of
detonation-gun sprayed Cr3C2-NiCr coating under high-temperature oxidation and
oxidation–erosion environments,” Surf. Coat. Technol., Vol. 206, pp. 530-541.
References
392
60. Kaushal, G., (2011), “Erosion-Corrosion Studies on High-Velocity Oxy-Fuel
Thermal Spray Coatings over Some Boiler Steels,” Ph.D. Thesis, Mechanical
Engineering, Punjab Technical University, Jalandhar (Punjab), India.
61. Kawahara, Y., (2007), “Application of High Temperature Corrosion-Resistant
Materials and Coatings under Severe Corrosive Environment in Waste-to-Energy
Boilers,” J. Therm. Spray Technol., Vol. 16, No. 2, pp. 202-213.
62. Kemdehoundja, M., Dinhut, J.F., Grosseau-Poussard, J.L. and Jeannin, M.,
(2006), “High temperature oxidation of Ni70Cr30 alloy: Determination of
oxidation kinetics and stress evolution in chromia layers by Raman
spectroscopy,” Mater. Sci. Eng. A, Vol. 435-436, pp. 666-671.
63. Khanna, A.S., Kumari, S., Kanungo, S. and Gasser, A., (2009), “Hard Coatings
Based on Thermal Spray and Laser Cladding,” Int. J. Refract. Met. Hard Mater.,
Vol. 27, pp. 485-491.
64. Khor, K.A., and Leh, N.L., (1993), Proc. ‘NTSC.,’ pp.613.
65. Kima, H.-J., Lee, C.-H. and Kweon, Y.-G., (2001), “The effects of sealing on the
mechanical properties of the plasma-sprayed alumina-titania coating,” Surf. Coat.
Technol., Vol. 139, pp. 75-80.
66. Koch, G.H., Brongers, M.P.H., Thompson, N.G., Virmani, Y.P. and Payer, J.H.,
(2002), “Historic Congressional Study: Corrosion Costs and Preventive Strategies
in the United States,” Supplement to Mater. Perfor., July, pp. 1-11.
67. Koiprasert, H. and Niranatlumpong, P., (2007), “Sealing of thermally-sprayed
stainless steel coatings against corrosion using nickel electroplating technique,”
Songklanakarin J. Sci. Technol., Vol. 29, No. 4, pp. 1029-1038.
68. Kong, G., Zhang, D., Brown, P.D., McCartney, D.G. and Harris, S.J., (2003),
“Microstructural Characterisation of High Velocity Oxy-Fuel Thermally Sprayed
Stellite-6,” Mater. Sci. Technol., Vol. 19, pp. 1003-1011.
69. Kumar, R., Tewari, V.K. and Prakash, S., (2007), “Studies on Hot Corrosion of
the 2.25Cr-1Mo Boiler Tube Steel and its Weldments in the Molten Salt Na2SO4-
60 pct V2O5 Environment,” Metall. Mater. Trans. A, Vol. 38A, pp. 54-57.
70. Lai, G.Y., (1990), “High Temperature Corrosion of Engineering Alloys,” ASM
International Book.
393
71. Laverde, D., Gomez-Acebo, T. and Castro, F., (2004), “Continuous and cyclic
oxidation of T91 ferritic steel under steam,” Vol. 46, No. 3, pp. 613-631.
72. Lawrencea, J. and Li, L., (2002), “Surface treatment of an Al2O3-based refractory
with CO2 and high power diode lasers for improved mechanical and chemical
resistance characteristics,” Surf. Coat. Technol., Vol. 162, pp. 93-100.
73. Lawrencea, J. and Lib, L., (2003), “Augmentation of the mechanical and
chemical resistance characteristics of an Al2O3-based refractory by means of high
power diode laser surface treatment,” J. Mater. Process. Technol., Vol. 142, pp.
461-465.
74. Li, C.L., Zhao, H.X., Matsumura, M., Takahashi, T., Asahara, M. and
Yamaguchi, H., (2000), “The effect of NiCr intermediate layer on corrosion
behavior of Cr2O3 ceramic coated materials,” Surf. Coat. Technol., Vol. 124, pp.
53-60.
75. Liang, J., Gao, W., Li, Z. and He, Y., (2004), “Hot corrosion resistance of
electrospark-deposited Al and Ni Cr coatings containing dispersed Y2O3
particles,” Materials Letters, Vol. 58, pp. 3280- 3284.
76. Lih, W.-C., Yang, S.H., Su, C.Y., Huang, S.C., Hsu, I.C. and Leu, M.S., (2000),
“Effects of Process Parameters on Molten Particle Speed and Surface
Temperature and the Properties of HVOF CrC/NiCr Coatings,” Surf. Coat.
Technol., Vol. 133-134, pp. 54-60.
77. Liscano, S., Gil, L. and Staia, M.H., (2004), “Effect of sealing treatment on the
corrosion resistance of thermal-sprayed ceramic coatings,” Surf. Coat. Technol.,
Vol. 188-189, pp. 135-139.
78. Liu, S.G., Wu, J.M., Zhang, S.C., Rong, S.J. and Li, Z.Z., (2007), “High
temperature erosion properties of arc-sprayed coatings using various cored wires
containing Ti–Al intermetallics,” Wear, Vol. 262, pp. 555-561.
79. Longa-Nava, Y., Zhang, Y.S., Takemoto, M. and Rapp, R.A., (1996), “Hot
Corrosion of Nickel-Chromium and Nickel-Chromium-Aluminum Thermal-Spray
Coatings by Sodium Sulfate-Sodium Metavanadate Salt,” Corros., Vol. 52, No. 9.
pp. 680-689.
References
394
80. Lugschider, E., Herbst, C. and Zhao, L., (1998), “Parameter Studies on High
Velocity Oxy-Fuel Spraying of MCrAIY Coatings,” Surf. Coat. Technol., Vol.
108-109, pp. 16-23.
81. Mahesh, R.A., Jayaganthan, R. and Prakash S., (2008A), “Evaluation of hot
corrosion behaviour of HVOF sprayed NiCrAl coating on superalloys at 900 °C,”
Mater. Chem. Phys., Vol. 111, pp. 524-533.
82. Mahesh, R.A., Jayaganthan, R. and Prakash, S., (2008B), “A study on hot
corrosion behaviour of Ni–5Al coatings on Ni- and Fe-based superalloys in an
aggressive environment at 900 °C,” J. Alloys Compd., Vol. 460, pp. 220-231.
83. Mahesh, R.A., Jayaganthan, R. and Prakash, S., (2009A), “Microstructural
characterization and hardness evaluation of HVOF sprayed Ni–5Al coatings on
Ni- and Fe-based superalloys,” J. Mater. Process. Technol., Vol. 209, pp. 3501-
3510.
84. Mahesh, R.A., Jayaganthan, R., Prakash, S., (2009B), “Microstructural
characteristics and mechanical properties of HVOF sprayed NiCrAl coating on
superalloys,” J. Alloys Compd., Vol. 468, pp. 392-405.
85. Mann, B.S., Arya, V. and Pant, B.K., (2010), “Enhanced Erosion Protection of
TWAS Coated Ti6Al4V Alloy Using Boride Bond Coat and Subsequent Laser
Treatment,” J. Mater. Engg. Perform., Vol. 20, No. 6, pp. 932-940.
86. Marvin, J.C., Jeffrey, F.H., Dan, N., (2005), “Fabrication, Construction, and
Operation Problems for Grade 91 Fossil Power Components,” J. Pres. Ves. Tech.,
Vol. 127, pp. 197-203.
87. Matthews, S., Hyland, M. and James, B., (2003), “Microhardness variation in
relation to carbide development in heat treated Cr3C2-NiCr thermal spray
coatings,” Acta Materialia, Vol. 51, pp. 4267-4277.
88. Matthews, S.J., (2004A), “Erosion-Corrosion of Cr3C2-NiCr High Velocity
Thermal Spray Coatings,” Ph.D. Thesis, The University of Auckland.
89. Matthews, S., Hyland, M. and James, B., (2004B), Long-Term Carbide
Development in High-Velocity Oxygen Fuel/High-Velocity Air Fuel Cr3C2-NiCr
Coatings Heat Treated at 900 oC,” J. Thermal Spray Technol., Vol. 13, No. 4, pp.
526-536.
395
90. Matthews, S.J., James, B.J. and Hyland, M.M., (2007), “Microstructural
influence on erosion behaviour of thermal spray coatings,” Mater. Charact., Vol.
58, pp. 59-64.
91. Matthews, S., James, B. and Hyland, M., (2009), “High temperature erosion of
Cr3C2-NiCr thermal spray coatings—The role of phase microstructure,” Surf.
Coat. Technol., Vol. 203, No. 9, pp. 1144-1153.
92. Matthews, S., James, B. and Hyland, M., (2010), “The Effect of Heat Treatment
on the Oxidation Mechanism of Blended Powder Cr3C2-NiCr Coatings,” J.
Therm. Spray Technol., Vol. 19, No. 1-2, pp. 119-127.
93. Metals Handbook, (1961), “Properties and Selection of Metals, 8th Edition,”
Vol. 1, ASM Publication, Metals Park Ohio.
94. Metals Handbook, (1975), “Failure analysis and Prevention,” Vol. 10, ASM
Publication, Metals Park OH, USA.
95. Miranda, J.C. and Ramalho, A., (2001), “Abrasion resistance of thermal sprayed
composite coatings with a nickel alloy matrix and a WC hard phase. Effect of
deposition technique and re-melting,” Tribol. Lett., Vol. 11, No. 1, pp. 37-48.
96. Mishra, S.B., Chandra, K., Prakash, S. and Venkataraman, B., (2005),
“Characterisation and erosion behaviour of a plasma sprayed Ni3Al coating on a
Fe-based superalloy,” Materials Letters, Vol. 59, pp. 3694-3698.
97. Moreau, C., Cielo, P. and Lamontagne, M., (1992), “Flattening and Solidification
of Thermal Sprayed Particles,” Proc. of 13th
Int. Therm. Spray Conf., Florida,
USA, pp. 761-766.
98. Morks, M.F., Berndt, C.C., Durandet, Y., Brandt, M. and Wang, J., (2010),
“Microscopic observation of laser yglazed yttria-stabilized zirconia coatings,”
Appl. Surf. Sci., Vol. 256, pp. 6213-6218.
99. Na, T., Xiaotian, J., Liling, G. and Zhengxin, L., (2000), “Effect of Post oxidation
on the Properties of Plasma Sprayed Ceramic Coatings,” Transactions of Metal
Heat Treatment, DOI cnki:ISSN:0254-587X.0.2000-04-004.
100. Nagarajan, R., Ambedkar, B., Gowrisankar, S. and Somasundaram, S., (2009),
“Development of predictive model for fly-ash erosion phenomena in coal-burning
boilers,” Wear, Vol. 267, pp. 122-128.
References
396
101. Nickel, H., Quadakkers, W.J. and Singheiser, L., (2002), “Analysis of Corrosion
Layers on Protective Coatings and High Temperature Materials in Simulated
Service Environments of Modern Power Plants Using SNMS, SIMS, SEM, TEM,
RBS and X-ray Diffraction Studies,” Anal. Bioanal. Chem., Vol. 374, pp. 581-
587.
102. Nicoll, A.R. and Wahl, G., (1983), “The Effect of Alloying Additions on M-Cr-
Al-Y Systems-An Experimental Study,” Thin Solid Films, Vol. 95, pp. 21-34.
103. Niranatlumpong, P., Ponton, C. B. and Evans, H. E., (2000), “The Failure of
Protective Oxides on Plasma-Sprayed NiCrAlY Overlay Coatings,” Oxid. Met.,
Vol. 53, No. 3-4, pp. 241-258.
104. Oksa, M., Turunen, E. and Varis, T., (2004), “Sealing of thermal spray coatings
for boiler applications”, Proc. International thermal spray conference, May 2004,
Osaka, Japan.
105. Otero, E., Merino, M.C., Pardo, A., Biezma, M.V. and Buitrago, G., (1987),
“Study on Corrosion Products of IN657 Alloy in Molten Salts,” Proc. of 10th
ICMC, Madras, India, Vol. IV, pp. 3583-3591.
106. Pawlowski, L., (1995), “The Science and Engineering of Thermal Spray
Coatings,” Wiley, NewYork.
107. Pettit, F.S. and Meier, G.H., (1984), “Oxidation and Hot Corrosion of
Superalloys,” Superalloys (1984), M. Gell, C. S. Kartovich, R. H. Bricknel, W.
B. Kent, J. F. Radovich (Eds.),The Met. Soc. of AIME, Warrendale, Pensylvania,
pp. 651-687.
108. Pettit, F.S. and Giggins, C.S., (1987), “Hot Corrosion, Ch. 12,” in ‘Superalloys
II,’ Eds. Sims, C.T., Stollof, N.S. and Hagel, W.C., Pub. Wiley Pub., N. Y.
109. Pokhmurska, H., Wielage, B., Lampke, T., Grund, T., Mykhajlo and Chervinska,
N., (2008), “Post-treatment of thermal spray coatings on magnesium,” Surf. Coat.
Technol., Vol. 202, pp. 4515-4524.
110. Portinha, A., Teixeira, V., Carneiro, J., Martins, J., Costa, M.F., Vassen, R. and
Stoever, D., (2005), “Characterization of thermal barrier coatings with a gradient
in porosity,” Surf. Coat. Technol., Vol. 195, No. 2-3, pp. 245-251.
397
111. Poza, P. and Grant, P.S., (2006), “Microstructure evolution of vacuum plasma
sprayed CoNiCrAlY coatings after heat treatment and isothermal oxidation,” Surf.
Coat. Technol., Vol. 201, pp. 2887-2896.
112. Qing, T., Zhi, S., Chun-long, Y. and Yun-qi, A., (2009), “Impact mechanism of
nano-sized TiO2 and SiO2 on corrosion resistance of electric arc spraying sealing
coat,” Procedia Earth and Planetary Science, Vol. 1, pp. 851-856.
113. Rajahram, S.S., Harvey, T.J. and Wood, R.J.K., (2009), “Erosion–corrosion
resistance of engineering materials in various test conditions,” Wear, Vol. 267,
pp. 244-254.
114. Rajahram, S.S., Harvey, T.J. and Wood, R.J.K., (2011), “Electrochemical
investigation of erosion–corrosion using a slurry pot erosion tester,” Tribol. Int.,
Vol. 44, pp. 232-240.
115. Rapp, R.A. and Zhang, Y.S., (1994), “Hot Corrosion of Materials: Fundamental
Studies,” JOM, Vol. 46, No. 12, pp. 47-55.
116. Ren, X., Wang, F. and Wang, X., (2005), “High-temperature oxidation and hot
corrosion behaviors of the NiCr–CrAl coating on a nickel-based superalloy,” Surf.
Coat. Technol., Vol. 198, pp. 425-431.
117. Rico, A., Gomez-Garcia, J., Munez, C.J., Poza, P. and Utrilla, V., (2009),
“Mechanical properties of thermal barrier coatings after isothermal oxidation.
Depth sensing indentation analysis,” Surf. Coat. Technol., Vol. 203, pp. 2307-
2314.
118. Roy, M., Pauschitz, A., Polak, R. and Franek, F., (2006), “Comparative
evaluation of ambient temperature friction behaviour of thermal sprayed Cr3C2–
25(Ni20Cr) coatings with conventional and nano-crystalline grains,” Tribol. Int.,
Vol. 39, pp. 29-38.
119. Ruhi, G., Modi, O.P., Sinha A.S.K. and Singh I.B., (2008), “Effect of sintering
temperatures on corrosion and wear properties of sol–gel alumina coatings on
surface pre-treated mild steel,” Corros. Sci., Vol. 50, pp. 639-649.
120. Saaedi, J., Coyle, T.W., Mirdamadi, S., Arabi, H. and Mostaghimi J., (2008),
“Phase formation in a Ni-050Cr HVOF coating,” Surf. Coat. Technol., Vol. 202,
pp. 5804-5811.
References
398
121. Saarivirta, E.H., Kalidakis, S., Stott, F.H., Perezc, F.J. and Lepisto, T., (2009),
“High-temperature erosion–oxidation of uncoated and FB-CVD aluminized and
aluminized–siliconized 9Cr–1Mo steel under fluidized-bed conditions,” Wear,
Vol. 267, pp. 2223-2234.
122. Saarivirta, E.H., Kalidakis, S., Stott, F.H., Rohr, V. and Schutze, M., (2010),
“Erosion-oxidation of uncoated, aluminized and chromized-aluminized 9Cr–1Mo
steels under fluidized-bed conditions at 550-700 °C,” Tribol. Int., Vol. 43, pp.
161-170.
123. Sachs, K., (1958), “Accelerated High Temperature Oxidation Due to Vanadium
Pentoxide,” Metallurgia, Apr., pp. 167-173.
124. Sadique, S.E., Mollah, A.H., Islam, M.S., Ali, M.M., Megat, M.H.H. and Basri,
S., (2000), “High-Temperature Oxidation Behavior of Iron-Chromium-Aluminum
Alloys,” Oxid. Met., Vol. 54, No. 5-6, pp. 385-400.
125. Saeidi, S., Voisey, K.T. and McCartney, D.G., (2009), “The Effect of Heat
Treatment on the Oxidation Behavior of HVOF and VPS CoNiCrAlY Coatings,”
J. Therm. Spray Technol., Vol. 18, No. 2, pp. 209-216.
126. Sahoo, P. and R. Raghuraman., (1993A), “Chromium Carbide Reinforced
Composite Coatings for High Temeprature Hard-Coat Applications. in Thermal
Spray: Research, Design, and Applications,” Anaheim, California: ASM
International, Materials Park, OH-USA.
127. Sahoo, P. and R. Raghuraman, (1993B), “High Temperature Chromium Carbide
Reinforced Metal Matrix Composite Coatings for Turbomachinery Applications,
in TS93: Thermal Spraying Conference,” Deutscher Verlag fur Schweisstechnik
DVS-Verlag GmbH. pp. 296-300.
128. Sahraoui, T., Fenineche, N.E., Montavon, G. and Coddet, C. (2003), “Structure
and Wear Behaviour of HVOF Sprayed Cr3C2-NiCr and WC-Co Coatings,”
Mater. Design, Vol. 24, pp. 309-313.
129. Saunders, S.R.J. and Nicholls, J.R., (1984), “Hot Salt Corrosion Test Procedures
and Coating Evaluation,” Thin Sold Films, Vol. 119, pp. 247-269.
399
130. Schutze, M., Malessa, M., Rohr, V. and Weber, T., (2006), “Development of
Coatings for Protection in Specific High Temperature Environments,” Surf. Coat.
Technol., Vol. 201, pp. 3872-3879.
131. Seiersten, M. and Kofstad, P., (1987), “The Effect of SO3 on Vanadate-Induced
Hot Corrosion,” High Temp. Technol., Vol. 5, No. 3, pp. 115-122.
132. Seong, B.G., Hwang, S.Y. and Kimb, K.Y., (2000), “High-temperature corrosion
of recuperators used in steel Mills,” Surf. Coat. Technol., Vol. 126, pp. 256-265.
133. Shi, L., (1993), “Accelerated Oxidation of Iron Induced by Na2SO4 Deposits in
Oxygen at 750 °C- A New Type Low-Temperature Hot Corrosion,” Oxid. Met.,
Vol. 40, No. 1-2, pp. 197-211.
134. Shibli, A. and Starr, F., (2007), “Some aspects of plant and research experience in
the use of new high strength martensitic steel P91,” Int. J. Pres. Ves. Pip., Vol. 84,
pp. 114-122.
135. Shirvani, K., Saremi, M., Nishikata, A. and Tsuru, T., (2003), “Electrochemical
study on hot corrosion of Si-modified aluminide coated In-738LC in Na2SO4-
20wt.% NaCl melt at 750 °C,” Corros. Sci., Vol. 45, pp. 1011-1021.
136. Shrestha, S., Neville, A. and Hodgkiess, T., (2001), “The Effect of Post-
Treatment of a High-Velocity Oxy-Fuel Ni-Cr-Mo-Si-B Coating Part I:
Microstructure/Corrosion Behavior Relationships,” J. Therm. Spray Technol.,
Vol. 10, No. 3, pp. 470-479.
137. Sidhu, B.S. and Prakash, S., (2003), “Evaluation of the Corrosion Behaviour of
Plasma-Sprayed Ni3Al Coatings on Steel in Oxidation and Molten Salt
Environments at 900 °C,” Surf. Coat. Technol., Vol. 166, pp. 89-100.
138. Sidhu, B.S. and Prakash, S., (2005A), “High-Temperature Oxidation Behavior of
NiCrA1Y Bond Coats and Stellite-6 Plasma-Sprayed Coatings,” Oxid. Met., Vol.
63, Nos. 3-4, pp. 241-259.
139. Sidhu, B.S. and Prakash, S., (2006A), “Studies on the behaviour of stellite-6 as
plasma sprayed and laser remelted coatings in molten salt environment at 900 °C
under cyclic conditions,” J. Mater. Process. Technol., Vol. 172, pp. 52-63.
References
400
140. Sidhu, B.S. and Prakash, S., (2006B), “Performance of NiCrAlY, Ni–Cr, Stellite-
6 and Ni3Al Coatings in Na2SO4–60% V2O5 Environment at 900 °C under Cyclic
Conditions,” Surf. Coat. Technol., Vol. 201, No. 3-4, pp. 1643-1654.
141. Sidhu, B.S. and Prakash, S., (2006C), “Evaluation of the Behavior of Shrouded
Plasma Spray Coatings in the Platen Superheater of Coal-Fired Boilers,” Metall.
and Mater. Trans. A, Vol. 37a, pp. 19-27.
142. Sidhu, B.S. and Prakash, S., (2006D), “Evaluation of the Behavior of Shrouded
Plasma Spray Coatings in the Platen Superheater of Coal-Fired Boilers,” Metall.
Mater. Trans. A, Vol. 37A, pp. 1927-1936.
143. Sidhu, B.S. and Prakash, S., (2006E), “Nickel-Chromium Plasma Spray Coatings:
A Way to Enhance Degradation Resistance of Boiler Tube Steels in Boiler
Environment,” J. Therm. Spray Technol., Vol. 15, No. 1, pp. 131-140.
144. Sidhu, B.S. and Prakash, S., (2007A), “Analytical Studies on the Behavior of
Nickel and Cobalt-Base Shrouded Plasma Spray Coatings at Elevated
Temperature in Air,” Oxid. Met., Vol. 67, pp. 279-298.
145. Sidhu, H.S., Singh, B.S. and Prakash, S., (2006F), “The Role of HVOF Coatings
in Improving Hot Corrosion Resistance of ASTM-SA210 GrA1 Steel in the
Presence of Na2SO4–V2O5 Salt Deposits,” Surf. Coat. Technol., Vol. 200, No. 18-
19, pp. 5386-5394.
146. Sidhu, H.S., Singh, B.S. and Prakash, S., (2006G), “Mechanical and
Microstructural Properties of HVOF Sprayed WC–Co and Cr3C2–NiCr Coatings
on the Boiler Tube Steels using LPG as the Fuel Gas,” J. of Mater. Process.
Technol., Vol. 171, pp. 77–82.
147. Sidhu, H.S., Sidhu, B.S. and Prakash, S., (2007B), “Solid particle erosion of
HVOF sprayed NiCr and Stellite-6 coatings,” Surf. Coat. Technol., Vol. 202, pp.
232-238.
148. Sidhu, H.S., Sidhu, B.S. and Prakash, S., (2007C), “Hot Corrosion Behavior of
HVOF Sprayed Coatings on ASTM SA213-T11 Steel,” J. Therm. Spray Technol.,
Vol. 16, No. 3, pp. 349-354.
401
149. Sidhu, T.S., Agrawal, R.D. and Prakash, S., (2005B), “Hot corrosion of some
superalloys and role of high-velocity oxy-fuel spray coatings—a review,” Surf.
Coat. Technol., Vol. 198, pp. 441- 446.
150. Sidhu, T.S., Prakash, S. and Agrawal, R.D., (2006H), “Evaluation of hot
corrosion resistance of HVOF coatings on a Ni-based superalloy in molten salt
environment,” Mater. Sci. Eng. A, Vol. 430, pp. 64-78.
151. Sidhu, T.S., Agarwal, R.D. and Prakash, S., (2006I), “Hot Corrosion Studies of
HVOF NiCrBSi and Stellite-6 Coatings on a Ni-based Superalloy in an Actual
Industrial Environment of a Coal Fired Boiler,” Surf. Coat. Technol., Vol. 201,
pp. 1602-1612.
152. Sidhu, T.S., Agarwal, R.D. and Prakash, S., (2006J), “Studies of the metallurgical
and mechanical properties of high velocity oxy-fuel sprayed stellite-6 coatings on
Ni- and Fe-based superalloys,” Surf. Coat. Technol., Vol. 201, pp. 273-281.
153. Sidhu, T.S., Agarwal, R.D. and Prakash, S., (2006K), “Hot Corrosion
Performance of a NiCr Coated Ni-based Alloy,” Scripta Mater., Vol. 55, pp. 179-
182.
154. Sidhu, T.S., Agarwal, R.D. and Prakash, S., (2006L), “Characterisations of
HVOF sprayed NiCrBSi coatings on Ni- and Fe-based superalloys and evaluation
of cyclic oxidation behaviour of some Ni-based superalloys in molten salt
environment,” Thin Solid Films, Vol. 515, pp. 95-105.
155. Sidhu, T.S., Prakash, S. and Agrawal, R.D., (2006M), “Performance of a High
Velocity Oxy-fuel Sprayed Coatings on a Fe-Based Superalloy in Na2SO4-
60%V2O5 Environment at 900 ºC, Part I: Characterisation of the Coatings,” J.
Mater. Engg. Perform., Vol. 15, No. 1, pp. 122 -129.
156. Sidhu, T.S., Prakash, S. and Agrawal, R.D., (2006N), “Performance of a High
Velocity Oxy-fuel Sprayed Coatings on a Fe-Based Superalloy in Na2SO4-
60%V2O5 Environment at 900 ºC, Part II: Hot Corrossion Behaviour of the
Coatings,” J. Mater. Engg. Perform., Vol. 15, No. 1, pp. 130-138.
157. Sidhu, T.S., Prakash, S. and Agrawal, R.D., (2006O), “Hot Corrosion Resistance
of HVOF Sprayed Coatings on a Ni-based Superalloy in Molten Salt
Environment,” J. Therm. Spray Technol., Vol. 15, No. 3, pp. 387-399.
References
402
158. Sidhu, T.S., Prakash, S. and Agrawal, R.D., (2006P), “Characterizations and Hot
Corrosion Resistance of Cr3C2-NiCr Coating on Ni-Base Superalloys in an
Aggressive Environment,” J. Therm. Spray Technol., Vol. 15, No. 4, pp. 811-816.
159. Sidhu, T.S., Prakash, S. and Agrawal, R.D., (2006Q), “Hot Corrosion Studies of
HVOF Sprayed Cr3C2-NiCr and Ni-20Cr coatings on a Nickel based Superalloy at
900 ºC,” Surf. Coat. Technol., Vol. 201, pp. 792-800.
160. Sidhu, T.S., Prakash, S. and Agrawal, R.D., (2007D), “Study of Molten Salt
Corrosion of High Velocity Oxy-Fuel Sprayed Cermet and Nickel-based Coatings
at 900 °C,” Metall. Mater. Trans. A, Vol. 38A, pp. 77-85.
161. Sidhu, T.S., Prakash, S. and Agrawal, R.D., (2007E), “Oxidation and Hot
Corrosion Resistance of HVOF WC-NiCrFeSiB Coating on Ni- and Fe-based
Superalloys at 800 °C,” J. Therm. Spray Technol., Vol. 16, No. 5-6, pp. 844-849.
162. Singh, B., (2003), “Studies on the Role of Coatings in Improving Resistance to
Hot Corrosion and Degradation,” Ph.D. Thesis, Met. & Mat. Eng. Dept., Indian
Institute of Technology Roorkee, Roorkee, India.
163. Singh, H., Puri, D. and Prakash, S., (2005A), “Some Studies on Hot Corrosion
Performance of Plasma Sprayed Coatings on a Fe-based Superalloy,” Surf. Coat.
Technol., Vol. 192, No. 1, pp. 27-38.
164. Singh, H., Puri, D. and Prakash, S., (2005B), “Some Studies on Hot Corrosion
Performance of Plasma Sprayed Coatings on a Fe-based Superalloy,” Surf. Coat.
Technol., Vol. 192, No. 1, pp. 27-38.
165. Singh, H., Puri, D. and Prakash, S., (2005C), “Corrosion Behavior of Plasma-
Sprayed Coatings on a Ni-Base Superalloy in Na2SO4-60 Pct V2O5 Environment
at 900 °C,” Metall. Mater. Trans. A, Vol. 36A, pp. 1007-1015.
166. Singh, H., Prakash, S., Puri, D. and Phase, D.M., (2006A), “Cyclic Oxidation
Behavior of Some Plasma-Sprayed Coatings in Na2SO4-60%V2O5 Environment,”
J. Mater. Engg. Perform., Vol. 15, No. 6, pp. 729-741.
167. Singh, K., (2006B), “Advances in materials for advanced steam cycle power
plants,” BHEL Journal, Vol. 27, No. 2, pp.
168. Sobolev, V.V., Guilemany, J.M. and Nutting, J., (2004), “HVOF Spraying,”
B0655, Maney, IOM3, pp. 5.
403
169. Song, Y., Zhou, C. and Xu, H., (2008), “Corrosion behavior of thermal barrier
coatings exposed to NaCl plus water vapor at 1050 °C,” Thin Solid Films, Vol.
516, pp. 5686-5689.
170. Souza, R.C., Voorwald, H.J.C. and Cioffi, M.O.H., (2008), “Fatigue strength of
HVOF sprayed Cr3C2–25NiCr and WC-10Ni on AISI 4340 steel,” Surf. Coat.
Technol., Vol. 203, pp.191-198.
171. Sreedhar, G., Alam, M.D.M. and Raja, V.S., (2009), “Hot corrosion behaviour of
plasma sprayed YSZ/Al2O3 dispersed NiCrAlY coatings on Inconel-718
superalloy,” Surf. Coat. Technol., Vol. 204, pp. 291-299.
172. Srikanth, S., Ravikumar, B., Das, S.K., Gopalakrishna, K., Nandakumar, K. and
Vijayan, P., (2003), “Analysis of Failures in Boiler Tubes Due to Fireside
Corrosion in a Waste Heat Recovery Boiler,” Eng. Failure Anal., Vol. 10, pp. 59-
66.
173. Srivastava, S.C., Godiwalla, K.M. and Banerjee, M.K., (1997), “Fuel ash
corrosion of boiler and superheater tubes,” J. Mater. Sci., Vol. 32, pp. 835-849.
174. Staia, M.H., Valente, T., Bartuli, C., Lewis, D.B. and Constable, C.P., (2001), “Part
I: Characterization of Cr3C2-25%NiCr Reactive Plasma Sprayed Coatings Produced
at Different Pressures,” Surf. Coat. Technol., Vol. 146-147, pp. 553-562.
175. Stein, K.J., Schorr, B.S. and Marder, A.R., (1999), “Erosion of Thermal Spray
MCr-Cr3C2 Cermet Coating,” Wear, Vol. 224, pp. 153-159.
176. Stewart, S., Ahmed, R. and Itsukaichi, T., (2005), “Rolling contact fatigue of
post-treated WC–NiCrBSi thermal spray coatings,” Surf. Coat. Technol., Vol.
190, pp. 171-189.
177. Stokes, J., (2003), “Production of Coated and Free-Standing Engineering
Components using the HVOF (High Velocity Oxy-Fuel) Process”, Ph.D. Thesis,
Dublin City University, Ireland.
178. Stokes, J., (2005), “The Theory and Application of the HVOF Thermal Spray
Process,” Dublin: Dublin City University.
179. Stott, F.H., (1998), “The Role of Oxidation in the Wear of Alloys,” Tribol. Int.,
Vol. 31, Nos. 1-3, pp. 61-71.
References
404
180. Stringer, J., (1987), “High Temperature Corrosion of Superalloys,” Mater. Sci.
Technol., Vol. 3, No. 7, pp. 482-493.
181. Stroosnijder, M.F., Mevrel, R. and Bennet, M.J., (1994), “The Interaction of
Surface Engineering and High Temperature Corrosion Protection,” Mater. High
Temp., Vol. 12, No. 1, pp. 53-66.
182. Suarez, M., Bellayer, S., Traisnel, M., Gonzalez, W., Chicot, D., Lesage, J.,
Puchi-Cabrera, E.S. and Staia, M.H., (2008), “Corrosion behavior of Cr3C2–NiCr
vacuum plasma sprayed coatings,” Surf. Coat. Technol., Vol. 202, No. 18, pp.
4566-4571.
183. Sundararajan, G., Phani, P.S., Jyothirmayi, A. and Gundakaram, R.C., (2009),
“The influence of heat treatment on the micro structural, mechanical and
corrosion behaviour of cold sprayed SS 316L coatings,” J of Mater Sci., Vol. 44,
pp. 2320-2326.
184. Sundararajan, T., Kuroda, S., Itagaki, T. and Abe, F., (2003A), “Steam
Oxidation Resistance of Ni-Cr Thermal Spray Coatings on 9Cr-1Mo Steel. Part 2:
50Ni-50Cr,” ISIJ Int., Vol. 43, No.1, pp. 104-111.
185. Sundararajan, T., Kuroda, S., Itagaki, T. and Abe, F., (2003B), “Steam
Oxidation Resistance of Ni-Cr Thermal Spray Coatings on 9Cr-1Mo Steel. Part 1:
80Ni-20Cr,” ISIJ Int., Vol. 43, No. 1, pp. 95-103.
186. Sundararajan, T., Kuroda, S., Nishida, K., Itagaki, T. and Abe, F., (2004A),
“Behaviour of Mn and Si in the Spray Powders during Steam Oxidation of Ni-Cr
Thermal Spray Coatings,” ISIJ Int., Vol. 44, pp. 139-144.
187. Sundararajan, T., Kuroda, S., Itagaki, T. and Abe, F., (2004B), “Steam
Oxidation Studies on 50Ni-50Cr HVOF Coatings on 9Cr-1Mo Steel: Change in
Structure and Morphology across the Coating/Substrate Interface,” Mater. Trans.,
Vol. 45, No. 4, pp. 1299-1305.
188. Tao, K., Zhou, X., Cui, H. and Zhang, J., (2009), “Microhardness variation in
heat-treated conventional and nanostructured NiCrC coatings prepared by HVAF
spraying,” Surf. Coat. Technol., Vol. 203, pp. 1406-1414.
405
189. Tang, Z., Wang, F. and Wu, W., (2000), “Effect of Al2O3 and enamel coatings on
900 °C oxidation and hot corrosion behaviors of gamma-TiAl,” Mater. Sci. Eng.
A, Vol. 276, pp. 70-75.
190. Thermal Spraying (1997): Practice, Theory, and Application, American welding
society, INC. 550 N. W. LeJeune road, Miami, Florida-33135.
191. Tillmann, W., Vogli, E., Baumann, I., Kopp, G. and Weihs, C., (2010),
“Desirability-Based Multi-Criteria Optimization of HVOF Spray Experiments to
Manufacture Fine Structured Wear-Resistant 75Cr3C2-25(NiCr20) Coatings,” J.
Therm. Spray Technol., Vol. 19, No. 1-2, pp. 392-408.
192. Tiwari, S.N. and Prakash, S., (1996), “Hot Corrosion Behaviour of Iron-Base
Superalloy in Salt Environment at Elevated Temperatures,” Proc. of Sympos.
Metals and Materials Research, Indian Institutie of Technology Madras, Madras,
4-5th July, pp. 107-117.
193. Tobe, S., Andoh, Y., Hidaka, K., Tanaka, K., Nishimura, S., Kawaharada, K. and
Shirai, K., (1999), “High Temperature Corrosion Resistance of Newly Developed
Cr-Based Alloy Coatings,” Tagungsband Conference Proceedings, Dusseldorf,
Germany.
194. Toma, D., Brandl, W. and Koester, U., (1999), “Studies on the Transient Stage of
Oxidation of VPS and HVOF Sprayed MCrAlY Coatings,” Surf. Coat. Technol.,
Vol. 120-121, pp. 8-15.
195. Torrell, M., Dosta, S., Miguel, J.R. and Guilemany, J.M., (2010), “Optimisation
of HVOF thermal spray coatings for their implementation as MSWI superheater
protectors,” Corros. Eng. Sci. Techn., Vol. 45, pp. 84-93.
196. Triantafyllidis, D., Li, L. and Stott, F.H., (2002), “Surface treatment of alumina
based ceramics using combined laser source,” Appl. Surf. Sci., Vol. 186, pp. 140-
144.
197. Tucker, Jr., R.C., (1994), “Ch. 11: Advanced Thermal Spray Deposition
Techniques,” in ‘Handbook of Deposition Technologies for Films & Coatings,’
Eds. R.F. Bunshah, Noyes Pub. Park Ridge, New Jersey, U. S. A./William
Andrew Publishing, LLC, Norwich, New York, U.S.A, pp. 591.
References
406
198. Ul-Hamid, A., (2003), “Diverse Scaling Behavior of the Ni-20Cr Alloy,” Maters.
Chem. Phys., Vol. 80, pp. 135-142.
199. Uusitalo, M.A., Vuoristo, P.M.J., Mantyla, T.A., (2002), “High temperature
corrosion of coatings and boiler steels in reducing chlorine-containing
atmosphere,” Surf. Coat. Technol., Vol. 161, pp. 275-285.
200. Uusitalo, M.A., Vuoristo, P.M.J. and Mantyla, T.A., (2003), “High Temperature
Corrosion of Coatings and Boiler Steels in Oxidizing Chlorine-containing
Atmosphere,” Mater. Sci. Eng. A, Vol. 346, pp. 168-177.
201. Uusitalo, M.A., Vuoristo, P.M.J. and Mantyla, T.A., (2004), “High temperature
corrosion of coatings and boiler steels below chlorine-containing salt deposits,”
Corros. Sci., Vol. 46, pp. 1311-1331.
202. Vardelle A. and Kuroda S., (2007), “Coatings under Severe Conditions,” J.
Therm. Spray Technol., Vol. 16, No. 1, pp. 1-2.
203. Venugopal, K. and Agrawal, M., (2008), “Evaluation of arc sprayed coatings for
erosion protection of tubes in atmospheric fluidised bed combustion (AFBC)
boilers,” Wear, Vol. 264, pp. 139-145.
204. Verdon, C., Karimi, A. and Martin, J.L., (1998), “A Study of High Velocity Oxy-
Fuel Thermally Sprayed Tungsten Carbide Based Coatings: Part 1.
Microstructures,” Mater. Sci. Eng. A, Vol. 246, pp. 11-24.
205. Vicenzi, J., Marques, C.M., Bergmann, C.P., (2008), “Hot and cold erosive wear
of thermal sprayed NiCr-based coatings: Influence of porosity and oxidation”,
Surf. Coat. Technol., Vol. 202, pp. 3688-3697.
206. Wang, B., Gong, J., Wang, A. Y., Sun, C., Huang, R. F. and Wen, L. S., (2002A),
“Oxidation Behavior of NiCrAlY Coatings on Ni-Based Superalloy,” Surf. Coat.
Technol.,Vol. 149, No. 1, pp. 70-75.
207. Wang, B.Q. and Lee, S.W., (1997), “Elevated temperature erosion of several
thermal-sprayed coatings under the simulated erosion conditions of in-bed tubes
in a fluidized bed combustor,” Wear, Vol. 203-204, pp. 580-587.
208. Wang, B.Q. and Verstak, A., (1999), “Elevated temperature erosion of HVOF
Cr3C 2/TiC–NiCrMo cermet coating,” Wear, Vol. 233-235, pp. 342-351.
407
209. Wang, B.Q., (2002B), “Effect of post heat treatment and sealing on erosion
resistance of several thermal sprayed coatings, in: S. Zhang (Ed.), Proceedings of
ICSE 2002, Southwest Jiaotong University Press, Chengdu, China, pp. 138-143.
210. Wang, B.Q. and Shui, Z.R., (2003A), “Hot erosion behavior of carbide–metal
composite coatings,” J. Mater. Process. Technol., Vol. 143-144, pp. 87-92.
211. Wang, B.Q., (2003B), “Hot erosion behavior of two new iron-based coatings
sprayed by HVCC process,” Wear, Vol. 255, pp. 102-109.
212. Wang, D., (1988), “Corrosion Behavior of Chromized and/or Aluminized 21/4Cr-
1Mo Steel in Medium-BTU Coal Gasifier Environments,” Surf. Coat.
Technol.,Vol. 36, pp. 49-60.
213. Wang, H.-T., Li, C.-J., Yang, G-J. and Li, C.-X., (2009), “Effect of heat treatment
on the microstructure and property of cold-sprayed nanostructured FeAl/Al2O3
intermetallic composite coating,” Vacuum, Vol. 83, pp 146-152.
214. Wang, Y., Jiang, S.L., Zheng, Y.G., Ke, W., Sun, W.H. and Wang, J.Q., (2011),
“Effect of porosity sealing treatments on the corrosion resistance of high-velocity
oxy-fuel (HVOF)-sprayed Fe-based amorphous metallic coatings,” Surf. Coat.
Technol., Vol. 206, pp. 1307-1318.
215. Westergard, R. and Hogmark, S., (2004), “Sealing to improve the wear
properties of plasma sprayed alumina by electro-deposited Ni,” Wear, Vol. 256,
pp. 1153-1162.
216. Weulersee, M.K., Moulin, G., Billard, P. and Pierotti, G., (2004), “High
Temperature Corrosion of Superheater Tubes in Waste Incinerators and Coal-
Fired Plants,” Mater.Sci. Forum, Vol. 461-464, pp. 973-980.
217. Wright, I.G., (1987), “High Temperature Erosion in Coal Combustion and
Conversion Processes: A Review,” Mater. Sci. Eng., Vol. 88, pp. 261-271.
218. Wu, Y.S., Qiu, W.Q., Yu, H.Y., Zhong, X.C., Liu, Z.W., Zeng, D.C. and Li, S.Z.,
(2011A), “Cycle oxidation behavior of nanostructured Ni60–TiB2 composite
coating sprayed by HVOF technique,” Appl. Surf. Sci., Vol. 257, pp. 10224-
10232.
219. Wu, Y.S., Zeng, D.C., Liu, Z.W., Qiu, W.Q., Zhong, X.C., Yu, H.Y. and Li, S.Z.,
(2011B), “Microstructure and sliding wear behavior of nanostructured Ni60–TiB2
References
408
composite coating sprayed by HVOF technique,” Surf. Coat. Technol., Vol. 206,
pp. 1102-1108.
220. Xie, G., Lu, Y., He, Z., Hu, B., Wang, K., Mo, X., Wu, Y. and Lin, P., (2008),
“Microstructure and corrosion properties of plasma-sprayed NiCr-Cr3C2 coatings
comparison with different post treatment,” Surf. Coat. Technol., Vol. 202, pp.
2885-2890.
221. Xue-mei, O., Zhi, S., Min, S. and Duan-lian, Z., (2008), “Hot-corrosion
mechanism of Ni-Cr coatings at 650 °C under different simulated corrosion
conditions,” J. China Univ. Min. Technol., Vol. 18, pp. 0444-0448.
222. Yang, Q., Cai, F., Zhao, L.R. and Huang, X., (2008), “Improving corrosion
resistance of CrTiAlN coating by post-deposition treatments,” Surf. Coat.
Technol., Vol. 203, pp. 606-609.
223. Zeng, Z., Sakoda, N. Tajiri, T. and Kuroda, S., (2008), “Structure and corrosion
behavior of 316L stainless steel coatings formed by HVAF spraying with and
without sealing,” Surf. Coat. Technol., Vol. 203, pp. 284-290.
224. Zhao, W.M., Wang, Y., Han, T., Wu, K.Y. and Xue, J., (2004), “Electrochemical
Evaluation of Corrosion Resistance of NiCrBSi Coatings Deposited by HVOF,”
Surf. Coat. Technol., Vol. 183, pp. 118-125.
225. Zhao, W.M., Wang, Y., Dong, L.X., Wu, K.Y. and Xue, J., (2005), “Corrosion
Mechanism of NiCrBSi Coatings Deposited by HVOF,” Surf. Coat. Technol.,
Vol. 190, pp. 293-298.
226. Zhang, D., Harris, S.J. and McCartney, D.G., (2003) “Microstructure Formation
and Corrosion Behaviour in HVOF-Sprayed Inconel 625 Coatings,” Mater. Sci.
Eng. A, Vol. 344, pp. 45-56.
227. Zhang, J., Wang, Z., Lin, P., Lu, W., Zhou, Z. and Jiang, S., (2010), “Effect of
Sealing Treatment on Corrosion Resistance of Plasma-Sprayed NiCrAl/Cr2O3-8
wt.%TiO2 Coating”, J. Therm. Spray Technol., http://dx.doi.org/10.1007/s11666-
010-9528-6.
228. Zhang, K., Liu, M.M., Liu, S.L., Sun, C. and Wang, F.H., (2011). “Hot corrosion
behaviour of a cobalt-base super-alloy K40S with and without NiCrAlYSi
coating,” Corros. Sci., Vol. 53. pp. 1990-1998.
409
229. Zhang, Q., Li, C.-J., Li, C.-X., Yang, G.-J. and Lui, S.-C., (2008A), “Study of
oxidation behavior of nanostructured NiCrAlY bond coatings deposited by cold
spraying,” Surf. Coat. Technol., Vol. 202, pp. 3378-3384.
230. Zhang S.-H., Cho T.-Y., Yoon J.-H., Fang W., Song K.-O., Li M.-X., Joo Y.-K.
and Lee C.G., (2008B), “Characterization of microstructure and surface properties
of hybrid coatings of WC–CoCr prepared by laser heat treatment and high
velocity oxygen fuel spraying”, Mater. Charact., Vol. 59, pp. 1412-1418.