MELJUN CORTES - HCCB Student Handbook (HOLY CHILD COLLEGES OF BUTUAN)
Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis
description
Transcript of Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis
![Page 1: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/1.jpg)
1
Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module
R&D and Design Analysis
Ying, Alice
With contributions fromM. Narula, H. Zhang, D. Papp
FNST Meeting August 12-14, 2008
UCLA
![Page 2: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/2.jpg)
2
HCCB Blanket Module Design
RAFS FW with He coolant channels
He purge gas pipe
Be (Be12Ti) pebbles
Ceramic breeder pebbles
Cooling plateHe coolant manifolds
for FW/Breeding zones
Helium (~8 MPa) coolant operating (350C-500C)
Low pressure (0.1-0.2 MPa) helium/%H2 purge gas to extract tritium
HCCB TBM module (710 389 510 mm)
![Page 3: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/3.jpg)
3
SummarySummary
• Efforts are being carried out in the following areas:– Utilizing the strain dependent thermo physical
characteristics of Be pebble beds for tritium performance optimization
– Investigate the creep failure of Li2TiO3 pebbles at high temperatures (as a part of thesis research for a master degree)
– Perform tritium permeation analysis for purge gas flow design (as a part of thesis research for a master degree)
![Page 4: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/4.jpg)
4
Strain dependent thermo physical property on tritium performance optimization
• The amount of the allowable beryllium in a breeding zone is limited by a maximum operating temperature of 600C
• The effective thermal conductivity of a Be pebble bed depends on:
keff = f(T, , )
Analysis method: neutronics and coupled thermo-fluid and thermo-mechanics analysis
![Page 5: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/5.jpg)
5
The trend of analysis is to incorporate a CAD model with various physics simulation codes
Be pebble bed zones
Breeder zone and associated coolant panels
FW coolant CAD model
Major parts of a 1/5th model of the HCCB module CAD model
![Page 6: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/6.jpg)
6Fe structure HeBe Li2TiO3
This CAD model was translated to a MCNP model input using MCAM (developed at ASIPP) for Neutronics analysis
![Page 7: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/7.jpg)
7
Overall temperature distributions in a Neutronics module are in the lower end of the allowable
temperature windows A look-alike test blanket module due to a lower neutron wall load of ITER as compared to that of a typical DEMO value
ITER 0.78 MW/m2
DEMO 2- 3 MW/m2
Be pebble bed strain profiles at 1 cm away from the back of the FW. Top: first iteration; bottom: second iteration.
![Page 8: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/8.jpg)
8
Impact on Design
1st Iteration 2nd Iteration 3rd Iteration
Keff increases as temperature and strain increase Be zone temperature
The effective thermal conductivity (near the FW region) increases from 2.25 to 5.8 W/m2K during the first iteration and decreases to 5.4 W/m2k at the second iteration; while the maximum temperature decrease of 43C at the first iteration and 1C at the second iteration.
This amount of temperature difference attributes to an additional 20% of Be added into the front zone region, where neutron multiplication can be enhanced.
![Page 9: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/9.jpg)
9
High temperature creep study for Li2TiO3 pebbles
Properties Li2TiO3
Density (g/cm3) 3.189
Porosity % 16
E young (GPa) 200.6
Coeff. Poisson ν
0.27
Tensile strength (MPa)
139
Compressive Strength
(MPa)1113
Conductivity (W/mK) at 298
K3.28
Li2TiO3 = 1.8 - 2 mm
All pebbles was checked at SEM to evaluate surface irregularities, cracks and shape before the tests
linear velocity-displacement transducer (LVDT)
Error < 0.1 μm
Deadweights to provide a
compressive load
Pebble under test
The tests were performed at:Temperature: 700, 800, 950 °C ;Load: 8, 16, 24, 30 N.
![Page 10: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/10.jpg)
10
SEM Images of deformed pebbles
Pebble after 4h deformation at 800C, under 16N load (left)
Pebble, cracked after 15hrs deformation at 800C under 20N load (right)
![Page 11: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/11.jpg)
11
Creep Failure Map (JAERI LiCreep Failure Map (JAERI Li22TiOTiO33 pebbles) pebbles)
Loading pressure (MPa)Ave
rag
eco
nta
ctfo
rce
s(N
)
0 2 4 6 8 100
10
20
30
DEM results
y = 3.413 x
Force distribution at contact under an applied loading of 2.0 MPa
The forces exerted on the pebbles during the operation should be less than 15 N; or the pressure applied to the pebble bed from containing structural less than ~ 5 MPa.
Preliminary finding
![Page 12: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/12.jpg)
12
Experiments provided time dependent deformation data for pebble creep deformation rate derivation (in progress)
Deformation along the axial direction
800C, 8N load
An FEM model was developed to predict the behavior of pebbles at high temperature under compressive loads.The material behavior was assumed to follow the general power-law rule:
nTBAet
/
Creep deformation rate is needed for the pebble bed thermo-mechanics analysis
![Page 13: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/13.jpg)
13
Tritium permeation analysis for purge gas flow design
Purge gas velocity profiles
breederbreeder
structure
coolant
Purge gas in
Neutronics (nuclear heating & tritium production rate) Fluid flow (velocity profile) Heat transfer (temperature)Tritium transport (permeation)
Purge gas out
![Page 14: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/14.jpg)
14
Tritium concentration profiles in various parts
Purge gas in
in Li2TiO3 bed
in He coolant in Structure
Purge gas out
4 3 2 1x10-5
Experiments are being conducted to validate numerical calculations:- blanket relevant pressure regime - with purge gas flow
![Page 15: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/15.jpg)
15
Some experimental results concerning pressure dependence on permeation
T = 673K, P0=13Pa, 6.65Pa, 1.3Pa
0 3600 7200 10800
0
1
2
3
4
5
Pdriving
= 5Torr = 665PaTemp = 623K
Exp1 Exp2 Cal. p=0.5 Cal. p=0.5 shift
Pre
ssur
e(P
a)
Time(s)
Compare with Calculation, P0=665Pa, T=623K, it is a good match with the Experimental result
T = 723K, P0=13Pa, 6.65Pa, 1.3Pa
12
22
22
2/12/12/1
0
exp)1(2
6)()(
n
nt
td
nD
nD
dPp
D
dPpt
d
PpdttJtQ
The total amount of gas which has permeated after time t is
J( t) DK sp
1/ 2
d1 2 ( 1)n exp D
n2 2
d2t
n1
D is the diffusion coefficient, Ks is its Sieverts’ constant. P = DKs is the permeability of the material
![Page 16: Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis](https://reader033.fdocuments.in/reader033/viewer/2022051000/56813e27550346895da80627/html5/thumbnails/16.jpg)
16
Experimental set-up underway to study the effect of velocity profile on tritium permeation