RanchChickenCoop - Tractor Supply Company · PDF fileRanchChickenCoop...
-
Upload
hoanghuong -
Category
Documents
-
view
221 -
download
0
Transcript of RanchChickenCoop - Tractor Supply Company · PDF fileRanchChickenCoop...
1
SKU: 1237423
Ranch Chicken Coop(102.4 in.L*63.0 in.W*75.7in. H)
Distributed by:TRACTOR SUPPLY COMPANY5401 VIRGINIA WAY,BRENTWOOD, TN 37027For customer support, call: 1-888-376-9601www.TractorSupply.comMADE IN CHINA
2
CARE INSTRUCTIONS
SAFETY INFORMATION:WARNING: Please keep children out of assembly area during assembly.
WARNING: This product is designed exclusively for chickens. Not intended forchildren.
BEFORE YOU BEGIN:Read instruction prior to assembly. This product contains parts that can be damaged ifincorrectly assembled. Please follow instructions. For steps where parts are placedupside down, place parts on a smooth surface to avoid scratching finish. Locate a flatlevel surface area to assemble and place coop for best results.
PRE-ASSEMBLY:TOOLS REQUIRED (not included): Power tool with Phillips Head Bit Adjustable Wrench Ruler
Two people are recommended to assemble this product.
PRODUCT OVERALL VIEW
R L
PARTS LIST
Part Image Description Quantity
1 2pcs
2
3
Left Roof Panel
4
1pc
5
6
3
L R
Right Roof Panel
Right Coop Panel
Left Coop Panel
Left Run Panel
Front&Back Run Panel
2pcs
1pc
1pc
2pcs
4
7 1pcFront Middle RunPanel
8
9
10
11
12
13
14
1pc
1pc
1pc
1pc
1pc
1pc
1pc
Back Middle RunPanel
Right Side RunPanel
Front Coop Panel
Back Coop Panel
Side Panel of NestingBox
Floor Panel of NestingBox
Nesting Box Lid withhinges
5
15
16
17
18
19
20
21
22
23
24
Drawer Base Frame
Drawer
Ladder
Roof cap
Roof cap
Door Panel Top Cap
Nesting box divider
Wooden Support Bars
Wooden Support Bars
Roosting Bar
1pc
1pc
1pc
1pc
1pc
1pc
3pcs
6pcs
2pcs
2pcs
6
A
B
C
D
E
F
G
H
Screws 12mm
Screws 14mm
Screws 30mm
Screws 35mm
Screws 40mm
Screws 50mm
4+1pcs
14+1pcs
2pcs
16+1pcs
58+2pcs
16+1pcs
1pc
1pairSupport Arm
Door pull lever
E
E
E
E
E
4
3
7
CAUTION: If using a cordless power drill / screwdriver, turn torque settingdown to a minimum level to start so that screws are not stripped. Adjust torqueup slightly if needed to fully tighten screws.
ASSEMBLY INSTRUCTIONStep 1: Attach the Front Coop Panel (10) and the Back Coop Panel (11) to the Right
Side Run Panel (9) using screws (E)*4pcs.
Step 2: Attach the Right Coop Panel (3) and the Left Coop Panel (4) using screws
(E)*12pcs as shown.
8
Step 3: Place the Drawer Base Frame (15) in place first, and then place the Drawer (16). Install the Roosting Bar (24) as shown.
1615
24
E
E
4
3
12
Step 4: Attach the Side Panel of Nesting Box (12) using screws(E)*4pcs as shown.
*** Note: You must open the chicken run door first to install 2 of the screws (F) *2pcs as seen in the picture below.
21
14
9
Step 5: Place the Floor Panel of Nesting Box (13) into the nesting box. And then
install the Nesting Box Dividers(21) as shown.
Step 6: Mount the Nesting Box Lid with hinges (14) to the coop using screws(B)*
6pcs as shown.
H R
H L
B
17
10
Step 7: Open the nesting box lid, and attach the Support Arm(H) using screws(B)*
8pcs.
***Note the different direction of support arms.
Step 8: Attach the Ladder (17) to the coop using screws(C)*2pcs as shown.
6 L
6 R
F
F F
F8
7
F
F
F
F
11
Step 9: Attach the Front Middle Run Panel (7) and Back Middle Run Panel (8) to
the coop using screws (F)*6pcs as shown.
Step 10: Attach the Front & Back Run Panel (6) using screws (F)*6pcs as shown.
5
F
12
Step 11: Attach the Left Run Panel (5) to the run panels using screws (E)*6pcs as
shown.
Step 12: Attach the Door Panel Top Cap (20) to the left run panel, using screws
(F)*2pcs as shown.
13
Step 13: Locate the Right Roof Panel (2) and position it on the ground with wooden
frame side up and the metal extension on your left side as seen in the picture below.
Next place the Wooden Support Bars (22) in place on the wooden frame (see picture
below) and secure in place with 3 screws each (E).
***NOTE: The orientation of the wooden support bar before screwing in place. The
Angle cut should be facing the center of the panel with the long end of the angle on
top as noted in picture. This allows the roof panel to be "self-centered" when placed
on top of coop and secure into place. Then place the roof on the right side as shown
using screws(D)*8pcs.
***Please note that the right place of the support bar as shown. You shall leave
3.7inches from one side, and 8.58inches on the other side as shown below.
E
E
2
2222
X 2
3.7in
8.58in
D
2 R
2 LD
3.7in
8.58in
E
E
14
Step 14: Next, place the Left Roof Panel (1) on the ground with wooden frame facingup. Position the Support Bars (22, 23) in place as per picture below and secure in place
with 3 screws each (E).
***NOTE: The orientation of the wooden support bar before screwing in place. The
Angle cut should be facing the center of the panel with the long end of the angle on top
as noted in picture. This allows the roof panel to be "self-centered" when placed on top
of coop. Then place the roof on the left side as shown and secure in place using screws
(D)*8pcs.
***Please note that the right place of the support bar as shown. You shall leave
3.7inches from one side, and 8.58inches from the other side as shown below.
D
D
E
E
1
22
23X 2
1 L
1 R
E
E
G
18
19
E
E
E
A
A
15
Step 15: Attach Roof caps(18)(19) using screws (E)*8pcs. Finally,use screws (A)
to secure the overlap of metal roof as shown in picture below.
Step 16: Place the Door Pull Lever(G) through hole in panel, and secure into place
by threading into door hardware located at the center of the sliding coop door.
16
Finished Coop