RANAP_PAGING Missing in Tracing Data
-
Upload
mohammedraziuddinakheel -
Category
Documents
-
view
41 -
download
7
description
Transcript of RANAP_PAGING Missing in Tracing Data
Document Title:RANAP:PAGING missing
Security Level: Internal
Technical case: RANAP:PAGING missing
When doing the additional test case IuCS_0006 MVIV test, we can not get the
RANAP:PAGING message in the tracing data (missing) as show in below.
After check with expect senior, check the configuration of the RNC. Below is
the information showed when LST RRCTRLSWITCH in LMT.
+++ RNCBESI03 2009-01-07 09:41:47
O&M #9722
%%LST RRCTRLSWITCH:;%%
RETCODE = 0 Execution succeeded.
List Process Switch
-------------------
Process switch = INVOKE_TRACE_SWITCH:OFF
= SYS_INFO_UPDATE_FOR_IU_RST:OFF
= DRNC_DIRECT_DSCR:OFF
= RNC_SHARE_SWITCH:ON
= RNCAP_IMSI_HO_SWITCH:OFF
2023-04-21 HUAWEI Confidential Page1, Total5
Document Title:RANAP:PAGING missing
Security Level: Internal
= TERMINAL_VERSION_DEBASE_SWITCH:OFF
= SYS_HO_OUT_CIPHER_SWITCH:OFF
= SYS_HO_CIPHER_CONFIG:ON
= BARRED_CELL_FOR_CSDOMAIN_RST:OFF
= CR2284R1_SWITCH:OFF
= CDT_MSG_FULL_TRACE:OFF
= CR2284R1_COMPATIBLE_SWITCH:ON
= COMBINE_OPERATION_DRD_SWITCH:ON
= UL_INTER_PROTECT_SWITCH:OFF
(Number of results = 1)
--- END
From the info above, we realize that CDT_MSG_FULL_TRACE is OFF. Next
step is executing the SET RRCTRLSWITCH command.
SET RRCTRLSWITCH: PROCESSSWITCH=CDT_MSG_FULL_TRACE-1;
List the process switch again.
+++ RNCBESI03 2009-01-07 09:42:52
O&M #9724
%%LST RRCTRLSWITCH:;%%
RETCODE = 0 Execution succeeded.
List Process Switch
-------------------
Process switch = INVOKE_TRACE_SWITCH:ON
= SYS_INFO_UPDATE_FOR_IU_RST:ON
= DRNC_DIRECT_DSCR:ON
= RNC_SHARE_SWITCH:ON
= RNCAP_IMSI_HO_SWITCH:ON
= TERMINAL_VERSION_DEBASE_SWITCH:ON
= SYS_HO_OUT_CIPHER_SWITCH:ON
= SYS_HO_CIPHER_CONFIG:ON
= BARRED_CELL_FOR_CSDOMAIN_RST:ON
= CR2284R1_SWITCH:ON
= CDT_MSG_FULL_TRACE:ON
= CR2284R1_COMPATIBLE_SWITCH:ON
= COMBINE_OPERATION_DRD_SWITCH:ON
= UL_INTER_PROTECT_SWITCH:ON
(Number of results = 1)
2023-04-21 HUAWEI Confidential Page2, Total5
Document Title:RANAP:PAGING missing
Security Level: Internal
--- END
After all, redo that test case again and we realize that we could get the right
result (RANAP:PAGING appears in the tracing data).
2023-04-21 HUAWEI Confidential Page3, Total5
Document Title:RANAP:PAGING missing
Security Level: Internal
Annex:
RAN 10 IuCS MVIV Test caseIuCS_0006 Mobile terminated SMS
Purpose
To verify the UE receive short message successfully
Initial conditions
1. UEa and UEb have registered the SMS service.
2. Set the correct short message center (SMC) address in UEa and UEb.
3. UEa and UEb have their locations updated successfully in VLR
4. Trace the Iu interface.
Test procedure
1. UEa sends a short message “12345” to UEb.
2. The short message “12345” is sent to UEb from SMC.
Result
1. UEa can send the short message successfully.
2. UEb can receive the message successfully.
3. The monitored message sequence is correct.
4. CN sends the paging message through the Iu interface.
5. After the paging is responded, CN uses the message “CP-DATA” to send the short message
and the time postmark to the UEb.
Message Sequence
Direction Observation Point
UTRA
N
CN-
CS
Layer n-
2Layer n-1 Layer n
çSCCP:
LUDTRANAP:PAGING
èSCCP:
CR
RANAP: Initial UE
MessageRR:PAGING RESPONSE
çSCCP:
CC
çSCCP:
DT1RANAP: Common ID
çSCCP:
DT1RANAP: Direct transfer
MM:AUTHENTICATION
REQUEST
èSCCP:
DT1RANAP: Direct transfer
MM: AUTHENTICATION
REPONSE
ç SCCP: RANAP: Security Mode
2023-04-21 HUAWEI Confidential Page4, Total5
Document Title:RANAP:PAGING missing
Security Level: Internal
DT1 Command
èSCCP:
DT1
RANAP: Security Mode
Complete
UEbçSMCSCCP:
DT1RANAP: Direct transfer SMS:CP DATA
UEb è SMCSCCP:
DT1RANAP: Direct transfer SMS:CP ACK
UEb è SMCSCCP:
DT1RANAP: Direct transfer SMS:CP DATA
UEbçSMCSCCP:
DT1RANAP: Direct transfer SMS:CP ACK
çSCCP:
DT1
RANAP: IU RELEASE
COMMAND
Remarks
None
2023-04-21 HUAWEI Confidential Page5, Total5