RAN14.0 Feature Activation Guide

RAN14.0

Feature Activation GuideIssue Date 05 2012-12-31

HUAWEI TECHNOLOGIES CO., LTD.

Copyright Huawei Technologies Co., Ltd. 2012. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissionsand other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.

NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.Address: Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China http://www.huawei.com [email protected]

Website: Email:

Issue 05 (2012-12-31)

Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd.

i

RAN14.0 Feature Activation Guide

About This Document

About This DocumentPurposeThis document provides guidelines for enabling or disabling a feature after initial configuration. Based on the activation, verification, and deactivation of a feature in the feature list, the guidelines aim to ensure that the feature is available on the network. This document describes how to activate a license and configure a feature in RAN.NOTE

The BSC6900 is used as an example to describe the network controller in this document.

Product VersionThe solution version is RAN14.0 related to this document, for more details you can refer to the following table. Product Name BSC6900 NodeB NodeB Product Version V900R014C00 V100R014 V200R014

Intended AudienceThis document is intended for: l l l l Technical support engineers Maintenance engineers Field engineers Network optimization engineers

Organization1 Changes in the RAN Feature Activation GuideIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. ii


About This Document

This chapter describes the changes in the RAN Feature Activation Guide. 2 Feature Activation and License Item Descriptions RANFeatures are classified into basic and optional features. Basic features are not licensecontrolled and therefore do not require license activation before use. Some optional features are license-controlled and therefore require license activation before use. If the Configuration Method column for a basic feature in the RAN basic feature list is None, enabling this feature does not involve any configurations. If the Configuration Method column for an optional feature in the RAN optional feature list is None, this feature is enabled once it is activated. 3 Overview of Configurations on the CME This section provides an overview of the configuration on the CME. The CME is a configuration tool on GUIs assisting you to effectively configure the data about wireless NE features. You can reconfigure configuration parameters by using the configuration expresses provided by the CME to activate or deactivate specified features. 4 Activating the UMTS License In the case of certain UMTS features, a license control item is defined for each feature. The license control item of a feature must be activated before the configuration and use of the feature. The license control items related to the RNC can be activated on the M2000 or RNC LMT, whereas those related to the NodeB can be activated only on the M2000. 5 Configuring 3.4/6.8/13.6/27.2Kbps RRC Connection and Radio Access Bearer Establishment and Release This section describes how to activate, verify, and deactivate the basic feature WRFD-010510 3.4/6.8/13.6/27.2Kbps RRC Connection and Radio Access Bearer Establishment and Release. 6 Configuring Conversational QoS Class This section describes how to activate, verify, and deactivate the basic feature WRFD-010501 Conversational QoS Class. 7 Configuring Streaming QoS Class This section describes how to activate, verify, and deactivate the basic feature WRFD-010502 Streaming QoS Class. 8 Configuring Interactive QoS Class This section describes how to activate, verify, and deactivate the basic feature WRFD-010503 Interactive QoS Class. 9 Configuring Background QoS Class This section describes how to activate, verify, and deactivate the basic feature WRFD-010504 Background QoS Class. 10 Configuring Emergency Call This section describes how to activate, verify, and deactivate the basic feature WRFD-021104 Emergency Call. 11 Configuring RAB Quality of Service Renegotiation over Iu Interface This section describes how to activate, verify, and deactivate the basic feature WRFD-010506 RAB Quality of Service Renegotiation over Iu Interface.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. iii


About This Document

12 Configuring 2-Way Antenna Receive Diversity This section describes how to activate, verify, and deactivate the basic feature MRFD-210604 2-Way Antenna Receive Diversity. 13 Configuring Cell Digital Combination and Split This section describes how to activate, verify, and deactivate the basic feature WRFD-010205 Cell Digital Combination and Split. 14 Configuring UE State in Connected Mode (CELL_DCH, CELL_PCH, URA_PCH, CELL_FACH) This section describes how to activate, verify, and deactivate the basic feature WRFD-010202 UE State in Connected Mode (CELL_DCH, CELL_PCH, URA_PCH, CELL_FACH). 15 Configuring Paging UE in Idle, CELL_PCH, URA_PCH State (Type 1) This section describes how to activate, verify, and deactivate the basic feature WRFD-010301 Paging UE in Idle, CELL_PCH, URA_PCH State (Type 1). 16 Configuring Paging UE in CELL_FACH, CELL_DCH State (Type 2) This section describes how to activate, verify, and deactivate the basic feature WRFD-010302 Paging UE in CELL_FACH, CELL_DCH State (Type 2). 17 Configuring Dynamic Channel Configuration Control This section describes how to activate, verify, and deactivate the basic feature WRFD-021101 Dynamic Channel Configuration Control (DCCC). (This feature cannot be configured using the CME. ) 18 Configuring Integrity Protection This section describes how to activate, verify, and deactivate the basic feature WRFD-011401 Integrity Protection. 19 Configuring Encryption This section describes how to activate, verify, and deactivate the basic feature WRFD-011402 Encryption. 20 Configuring Open Loop Power Control This section describes how to activate, verify, and deactivate the basic feature WRFD-020501 Open Loop Power Control. 21 Configuring Downlink Power Balance This section describes how to activate, verify, and deactivate the basic feature WRFD-020502 Downlink Power Balance. 22 Configuring Outer Loop Power Control This section describes how to activate, verify, and deactivate the basic feature WRFD-020503 Outer Loop Power Control. 23 Configuring Inner Loop Power Control This section describes how to activate, verify, and deactivate the basic feature WRFD-020504 Inner Loop Power Control.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. iv


About This Document

24 Configuring Admission Control This section describes how to activate, verify, and deactivate the basic feature WRFD-020101 Admission Control. 25 Configuring Load Measurement This section describes how to activate, verify, and deactivate the basic feature WRFD-020102 Load Measurement. 26 Configuring Load Reshuffling This section describes how to activate, verify, and deactivate the basic feature WRFD-020106 Load Reshuffling. 27 Configuring Overload Control This section describes how to activate, verify, and deactivate the basic feature WRFD-020107 Overload Control. 28 Configuring Code Resource Management This section describes how to activate, verify, and deactivate the optional feature WRFD-020108 Code Resource Management. 29 Configuring Potential User Control This section describes how to activate, verify, and deactivate the optional feature WRFD-020105 Potential User Control. 30 Configuring Cell Barring This section describes how to activate, verify, and deactivate the optional feature WRFD-021102 Cell Barring. 31 Configuring Shared Network Support in Connected Mode This section describes how to activate, verify, and deactivate the basic feature WRFD-021301 Shared Network Support in Connected Mode. (This feature cannot be configured using the CME. ) 32 Configuring Intra NodeB Softer Handover This section describes how to activate, verify, and deactivate the basic feature WRFD-020201 Intra NodeB Softer Handover. 33 Configuring Intra RNC Soft Handover This section describes how to activate, verify, and deactivate the basic feature WRFD-020202 Intra RNC Soft Handover. 34 Configuring Inter RNC Soft Handover This section describes how to activate, verify, and deactivate the optional feature WRFD-020203 Inter RNC Soft Handover. 35 Configuring Intra Frequency Hard Handover This section describes how to activate, verify, and deactivate the optional feature WRFD-020301 Intra Frequency Hard Handover. 36 Configuring Intra RNC Cell UpdateIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. v


About This Document

This section describes how to activate, verify, and deactivate the basic feature WRFD-010801 Intra RNC Cell Update. 37 Configuring Inter RNC Cell Update This section describes how to activate, verify, and deactivate the basic feature WRFD-010802 Inter RNC Cell Update. 38 Configuring Intra RNC URA Update This section describes how to activate, verify, and deactivate the basic feature WRFD-010901 Intra RNC URA Update. 39 Configuring Inter RNC URA Update This section describes how to activate, verify, and deactivate the basic feature WRFD-010902 Inter RNC URA Update. 40 Configuring Direct Signaling Connection Re-establishment (DSCR) This section describes how to activate, verify, and deactivate the basic feature WRFD-021400 Direct Signaling Connection Re-establishment (DSCR). 41 Configuring CS Fallback Guarantee for LTE Emergency Calls This section describes how to activate, verify, and deactivate the basic feature WRFD-140102 CS Fallback Guarantee for LTE Emergency Calls. For details about how to configure this feature on the LTE side, see the related documents provided by the LTE equipment vendor. 42 Configuring NodeB Clock This section describes how to activate, verify, and deactivate the basic feature MRFD-210501 NodeB Clock. 43 Configuring Dynamic AAL2 Connections in Iub/IuCS/Iur Interface This section describes how to activate, verify, and deactivate the basic feature WRFD-05030104 Dynamic AAL2 Connections in Iub/IuCS/Iur Interface. 44 Configuring Permanent AAL5 Connections for Control Plane Traffic This section describes how to activate, verify, and deactivate the basic feature WRFD-05030105 Permanent AAL5 Connections for Control Plane Traffic. 45 Configuring Call Admission Based on Used AAL2 Path Bandwidth This section describes how to activate, verify, and deactivate the basic feature WRFD-05030106 Call Admission Based on Used AAL2 Path Bandwidth. 46 Configuring CBR, rt-VBR, nrt-VBR, UBR ATM QoS Classes This section describes how to activate, verify, and deactivate the basic feature "WRFD-05030107 CBR, rt-VBR, nrt-VBR, UBR ATM QoS Classes". 47 Configuring F5 This section describes how to activate, verify, and deactivate the basic feature WRFD-05030110 F5. (This feature cannot be configured using the CME. ) 48 Configuring UBR+ ATM QoS Class This section describes how to activate, verify, and deactivate the basic feature "WRFD-050305 UBR+ ATM QoS Class".Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. vi


About This Document

49 Configuring Link Aggregation This section describes how to activate, verify, and deactivate the basic feature MRFD-210103 Link Aggregation. 50 Configuring Flow Control This section describes how to activate, verify, and deactivate the basic feature WRFD-040100 Flow Control. 51 Configuring BOOTP This section describes how to activate, verify, and deactivate the basic feature WRFD-031100 BOOTP. In ATM transport mode, the NodeB can automatically set up the OM channel with the BSC6900 by using the BOOTSTRAP Protocol (BOOTP) function. 52 Configuring NodeB Self-Discovery Based on IP Mode This section describes how to activate, verify, and deactivate the basic feature WRFD-031101 NodeB Self-Discovery Based on IP Mode. 53 Configuring License Control for Urgency This section describes how to activate, verify, and deactivate the basic feature WRFD-040300 License Control for Urgency. (This feature cannot be configured using the CME. ) 54 Configuring Intelligently Out of Service This section describes how to activate, verify, and deactivate the basic feature WRFD-031000 Intelligently Out of Service. 55 Configuring OCNS This section describes how to activate, verify, and deactivate the basic feature WRFD-031200 OCNS (Orthogonal Channel Noise Simulator). (This feature cannot be configured using the CME. ) 56 Configuring Power Off the Equipment Level by Level This section describes how to activate, verify, and deactivate the basic feature WRFD-031400 Power Off the Equipment Level by Level. 57 Configuring Solar Power Device Management This section describes how to activate, verify, and deactivate the basic feature WRFD-031500 Solar Power Device Management. 58 Configuring Connection with TMA (Tower Mounted Amplifier) This section describes how to activate, verify, and deactivate the basic feature MRFD-210601 Connection with TMA (Tower Mounted Amplifier). (This feature cannot be configured using the CME. ) 59 Configuring Remote Electrical Tilt This section describes how to activate, verify, and deactivate the basic feature MRFD-210602 Remote Electrical Tilt. (This feature cannot be configured using the CME. ) 60 Configuring Same Band Antenna Sharing Unit (900 MHz)Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. vii


About This Document

This section describes how to activate, verify, and deactivate the basic feature WRFD-060003 Configuring Same Band Antenna Sharing Unit (900 MHz). (This feature cannot be configured using the CME. ) 61 Configuring VoIP over HSPA/HSPA+ This section describes how to activate, verify, and deactivate the optional feature WRFD-010617 VoIP over HSPA/HSPA+. 62 Configuring Optimized Scheduling for VoIP over HSPA This section describes how to activate, verify, and deactivate the optional feature WRFD-01061703 Optimized Scheduling for VoIP over HSPA. 63 Configuring IMS Signaling over HSPA This section describes how to activate, verify, and deactivate the basic feature WRFD-010618 IMS Signaling over HSPA. 64 Configuring PDCP Header Compression (RoHC) This section describes how to activate, verify, and deactivate the optional feature WRFD-011501 PDCP Header Compression (RoHC). 65 Configuring CS Voice over HSPA/HSPA+ This section describes how to activate, verify, and deactivate the optional feature WRFD-010619 CS Voice over HSPA/HSPA+. 66 Configuring AMR-WB (Adaptive Multi Rate Wide Band) This section describes how to activate, verify, and deactivate the optional feature WRFD-010613 AMR-WB (Adaptive Multi Rate Wide Band). (This feature cannot be configured using the CME. ) 67 Configuring AMR/WB-AMR Speech Rates Control This section describes how to activate, verify, and deactivate the basic feature WRFD-020701 AMR/WB-AMR Speech Rates Control. 68 Configuring TFO/TrFO This section describes how to activate, verify, and deactivate the optional feature WRFD-011600 TFO/TrFO. 69 Configuring AMR Voice Quality Improvement Based on PLVA This section describes how to activate, verify, and deactivate the optional feature WRFD-140201 AMR Voice Quality Improvement Based on PLVA. 70 Configuring Cell Broadcast Service This section describes how to activate, verify, and deactivate the optional feature WRFD-011000 Cell Broadcast Service. 71 Configuring Simplified Cell Broadcast This section describes how to activate, verify, and deactivate the optional feature WRFD-011001 Simplified Cell Broadcast. 72 Configuring Warning of DisasterIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. viii


About This Document

This section describes how to activate, verify, and deactivate the optional feature WRFD-020127 Warning of Disaster. 73 Configuring MBMS Introduction Package This section describes how to activate, verify, and deactivate the optional feature WRFD-010616 MBMS Introduction Package. 74 Configuring MBMS Admission Control This section describes how to activate, verify, and deactivate the optional feature WRFD-01061602 MBMS Admission Control. 75 Configuring MBMS Load Control This section describes how to activate, verify, and deactivate the optional feature WRFD-01061603 MBMS Load Control. 76 Configuring MBMS Transport Resource Management This section describes how to activate, verify, and deactivate the optional feature WRFD-01061605 MBMS Transport Resource Management. 77 Configuring Streaming Service on MBMS This section describes how to activate, verify, and deactivate the optional feature WRFD-01061606 Streaming Service on MBMS. 78 Configuring 16/32/64/128Kbps Channel Rate on MBMS This section describes how to activate, verify, and deactivate the optional feature WRFD-01061608 16/32/64/128Kbps Channel Rate on MBMS. 79 Configuring MBMS Phase 2 This section describes how to activate, verify, and deactivate the optional feature WRFD-010660 MBMS Phase 2. 80 Configuring MBMS Enhanced Broadcast Mode This section describes how to activate, verify, and deactivate the optional feature WRFD-01066001 MBMS Enhanced Broadcast Mode. 81 Configuring MBMS P2P over HSDPA This section describes how to activate, verify, and deactivate the optional feature WRFD-01066002 MBMS P2P over HSDPA. 82 Configuring MBMS Admission Enhancement This section describes how to activate, verify, and deactivate the optional feature WRFD-01066003 MBMS Admission Enhancement. 83 Configuring Inter-Frequency Neighboring Cell Selection for MBMS PTP Users This section describes how to activate, verify, and deactivate the optional feature WRFD-01066004 Inter-Frequency Neighboring Cell Selection for MBMS PTP Users. 84 Configuring FACH Transmission Sharing for MBMS This section describes how to activate, verify, and deactivate the optional feature WRFD-010627 FACH Transmission Sharing for MBMS.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. ix


About This Document

85 Configuring MBMS FLC(Frequency Layer Convergence)/FLD(Frequency Layer Dispersion) This section describes how to activate, verify, and deactivate the optional feature WRFD-010626 MBMS FLC(Frequency Layer Convergence)/FLD(Frequency Layer Dispersion). 86 Configuring MBMS over Iur This section describes how to activate, verify, and deactivate the optional feature WRFD-010661 MBMS over Iur. 87 Configuring Dynamic Power Estimation for MTCH This section describes how to activate, verify, and deactivate the optional feature WRFD-010662 Dynamic Power Estimation for MTCH. 88 Configuring MSCH Scheduling This section describes how to activate, verify, and deactivate the optional feature WRFD-010663 MSCH Scheduling. 89 Configuring MBMS Channel Audience Rating Statistics This section describes how to activate, verify, and deactivate the optional feature WRFD-010665 MBMS Channel Audience Rating Statistics. 90 Configuring Cell ID + RTT Function Based LCS This section describes how to activate, verify, and deactivate the optional feature WRFD-020801 Cell ID + RTT Function Based LCS. 91 Configuring OTDOA Based LCS This section describes how to activate, verify, and deactivate the optional feature WRFD-020802 OTDOA Based LCS. 92 Configuring A-GPS Based LCS This section describes how to activate, verify, and deactivate the optional feature WRFD-020803 A-GPS Based LCS. (This feature cannot be configured using the CME. ) 93 Configuring LCS Classified Zones This section describes how to activate, verify, and deactivate the optional feature WRFD-020804 LCS Classified Zones. 94 Configuring LCS over Iur This section describes how to activate, verify, and deactivate the optional feature WRFD-020805 LCS over Iur. 95 Configuring Iupc Interface for LCS Service This section describes how to activate, verify, and deactivate the optional feature WRFD-020807 Iupc Interface for LCS service. 96 Configuring Push to Talk This section describes how to activate, verify, and deactivate the optional feature WRFD-020134 Push to Talk. (This feature cannot be configured using the CME. ) 97 Configuring HSUPA Introduction PackageIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. x


About This Document

This section describes how to activate, verify, and deactivate the optional feature WRFD-010612 HSUPA Introduction Package. 98 Configuring HSUPA Admission Control This section describes how to activate, verify, and deactivate the optional feature WRFD-01061202 HSUPA Admission Control. 99 Configuring HSUPA Power Control This section describes how to activate, verify, and deactivate the optional feature WRFD-01061203 HSUPA Power Control. 100 Configuring HSUPA Mobility Management This section describes how to activate, verify, and deactivate the optional feature WRFD-01061204 HSUPA Mobility Management. 101 Configuring HSUPA DCCC This section describes how to activate, verify, and deactivate the optional feature WRFD-01061208 HSUPA DCCC. 102 Configuring 20 HSUPA Users per Cell This section describes how to activate, verify, and deactivate the optional feature WRFD-01061211 20 HSUPA Users per Cell. 103 Configuring HSUPA Iub Flow Control in Case of Iub Congestion This section describes how to activate, verify, and deactivate the optional feature WRFD-01061212 HSUPA Iub Flow Control in Case of Iub Congestion. 104 Configuring HSUPA E-AGCH Power Control (Based on CQI or HS-SCCH) This section describes how to activate, verify, and deactivate the optional feature WRFD-01061401 HSUPA E-AGCH Power Control (Based on CQI or HS-SCCH). 105 Configuring HSUPA 2ms TTI This section describes how to activate, verify, and deactivate the optional feature WRFD-01061403 HSUPA 2ms TTI. 106 Configuring HSUPA 2 ms/10 ms TTI Handover This section describes how to activate, verify, and deactivate the optional feature WRFD-01061404 HSUPA 2 ms/10 ms TTI Handover. 107 Configuring HSUPA 5.74Mbps per User This section describes how to activate, verify, and deactivate the optional feature WRFD-01061405 HSUPA 5.74Mbps per User. 108 Configuring Streaming Traffic Class on HSUPA This section describes how to activate, verify, and deactivate the optional feature WRFD-010632 Streaming Traffic Class on HSUPA. 109 Configuring HSUPA over Iur This section describes how to activate, verify, and deactivate the optional feature WRFD-010635 HSUPA over Iur.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xi


About This Document

110 Configuring TTI Switch for BE Services Based on Coverage This section describes how to activate, verify, and deactivate the optional feature WRFD-010690 TTI Switch for BE Services Based on Coverage. 111 Configuring HSUPA Adaptive Transmission This section describes how to activate, verify, and deactivate the optional feature WRFD-010641 HSUPA Adaptive Transmission. 112 Configuring Dynamic CE Resource Management This section describes how to activate, verify, and deactivate the optional feature WRFD-010638 Dynamic CE Resource Management. 113 Configuring HSUPA FDE This section describes how to activate, verify, and deactivate the optional feature WRFD-010692 HSUPA FDE. 114 Configuring Adaptive Configuration of Traffic Channel Power offset for HSUPA This section describes how to activate, verify, and deactivate the optional feature WRFD-010712 Adaptive Configuration of Traffic Channel Power offset for HSUPA. 115 Configuring Anti-Interference Scheduling for HSUPA This section describes how to activate, verify, and deactivate the optional feature WRFD-020136 Anti-Interference Scheduling for HSUPA. 116 Configuring Dual-Threshold Scheduling with HSUPA Interference Cancellation This section describes how to activate, verify, and deactivate the optional feature WRFD-020137 Dual-Threshold Scheduling with HSUPA Interference Cancellation. 117 Configuring 60 HSUPA Users per Cell This section describes how to activate, verify, and deactivate the optional feature WRFD-010634 60 HSUPA Users per Cell. 118 Configuring HSUPA UL Interference Cancellation This section describes how to activate, verify, and deactivate the optional feature WRFD-010691 HSUPA UL Interference Cancellation. 119 Configuring SRB over HSUPA This section describes how to activate, verify, and deactivate the optional feature WRFD-010636 SRB over HSUPA. 120 Configuring Control Channel Parallel Interference Cancellation (Phase 2) This section describes how to activate, verify, and deactivate the optional feature WRFD-140202 Control Channel Parallel Interference Cancellation (Phase 2). Control Channel Parallel Interference Cancellation is short for CCPIC. 121 Configuring HSDPA Introduction Package This section describes how to activate, verify, and deactivate the optional feature WRFD-010610 HSDPA Introduction Package. (This feature cannot be configured using the CME. ) 122 Configuring 15 Codes per CellIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xii


About This Document

This section describes how to activate, verify, and deactivate the optional feature WRFD-01061001 15 Codes per Cell. 123 Configuring Time and HS-PDSCH Codes Multiplex This section describes how to activate, verify, and deactivate the optional feature WRFD-01061018 Time and HS-PDSCH Codes Multiplex. 124 Configuring HSDPA H-ARQ & Scheduling (MAX C/I, RR, and PF) This section describes how to activate, verify, and deactivate the optional feature WRFD-01061009 HSDPA H-ARQ & Scheduling (MAX C/I, RR, and PF). 125 Configuring HSDPA Static Code Allocation and RNC-Controlled Dynamic Code Allocation This section describes how to activate, verify, and deactivate the optional feature WRFD-01061005 HSDPA Static Code Allocation and RNC-Controlled Dynamic Code Allocation. 126 Configuring HSDPA Power Control This section describes how to activate, verify, and deactivate the optional feature WRFD-01061004 HSDPA Power Control. 127 Configuring HSDPA Admission Control This section describes how to activate, verify, and deactivate the optional feature WRFD-01061003 HSDPA Admission Control. 128 Configuring Improvement of User Experience in Low Traffic Service This section describes how to activate, verify, and deactivate the optional feature WRFD-01061020 Improvement of User Experience in Low Traffic Service. 129 Configuring HSDPA Flow Control This section describes how to activate, verify, and deactivate the optional feature WRFD-01061010 HSDPA Flow Control. 130 Configuring HSDPA Mobility Management This section describes how to activate, verify, and deactivate the optional feature WRFD-01061006 HSDPA Mobility Management. 131 Configuring HSDPA UE Category 1 to 28 This section describes how to activate, verify, and deactivate the optional feature WRFD-01061002 HSDPA UE Category 1 to 28. 132 Configuring DL 16QAM Modulation This section describes how to activate, verify, and deactivate the optional feature WRFD-010629 DL 16QAM Modulation. 133 Configuring Dynamic Code Allocation Based on NodeB This section describes how to activate, verify, and deactivate the optional feature WRFD-010631 Dynamic Code Allocation Based on NodeB. 134 Configuring HSDPA Enhanced PackageIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xiii


About This Document

This section describes how to activate, verify, and deactivate the optional feature WRFD-010611 HSDPA Enhanced Package. 135 Configuring Scheduling based on EPF and GBR This section describes how to activate, verify, and deactivate the optional feature WRFD-01061103 Scheduling based on EPF and GBR. 136 Configuring HSDPA State Transition This section describes how to activate, verify, and deactivate the optional feature WRFD-01061111 HSDPA State Transition. 137 Configuring HSDPA DRD This section describes how to activate, verify, and deactivate the optional feature WRFD-01061112 HSDPA DRD. 138 Configuring HS-DPCCH Preamble Support This section describes how to activate, verify, and deactivate the optional feature WRFD-01061113 HS-DPCCH Preamble Support. 139 Configuring Streaming Traffic Class on HSDPA This section describes how to activate, verify, and deactivate the optional feature WRFD-010630 Streaming Traffic Class on HSDPA. 140 Configuring HSDPA over Iur This section describes how to activate, verify, and deactivate the optional feature WRFD-010651 HSDPA over Iur. 141 Configuring SRB over HSDPA This section describes how to activate, verify, and deactivate the optional feature WRFD-010652 SRB over HSDPA. 142 Configuring CQI Adjustment Based on Dynamic BLER Target This section describes how to activate, verify, and deactivate the optional feature WRFD-030010 CQI Adjustment Based on Dynamic BLER Target. 143 Configuring MIMO Prime This chapter describes how to activate, verify, and deactivate the basic feature WRFD-030011 MIMO Prime. 144 Configuring Adaptive Configuration of Typical HSPA Rate This section describes how to activate, verify, and deactivate the optional feature WRFD-030004 Adaptive Configuration of Typical HSPA Rate. 145 Configuring HSDPA Scheduling Based on UE Location This section describes how to activate, verify, and deactivate the optional feature WRFD-140221 HSDPA Scheduling Based on UE Location. 146 Configuring Adaptive Adjustment of HSUPA Small Target Retransmissions This section describes how to activate, verify, and deactivate the optional feature WRFD-140222 Adaptive Adjustment of HSUPA Small Target Retransmissions.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xiv


About This Document

147 Configuring HSPA+ Downlink 28Mbps per User This section describes how to activate, verify, and deactivate the optional feature WRFD-010680 HSPA+ Downlink 28Mbps per User. 148 Configuring HSPA+ Downlink 21Mbps per User This section describes how to activate, verify, and deactivate the optional feature WRFD-010681 HSPA+ Downlink 21Mbps per User. 149 Configuring Downlink Enhanced L2 This section describes how to activate, verify, and deactivate the optional feature WRFD-010685 Downlink Enhanced L2. 150 Configuring HSPA+ Downlink 42Mbps per User This section describes how to activate, verify, and deactivate the optional feature WRFD-010689 HSPA+ Downlink 42Mbps per User. 151 Configuring Downlink 64QAM This section describes how to activate, verify, and deactivate the optional feature WRFD-010683 Downlink 64QAM. 152 Configuring 2x2 MIMO This section describes how to activate, verify, and deactivate the optional feature WRFD-010684 2x2 MIMO. Multiple Input Multiple Output (MIMO) is a multi-antenna technology, which enables multiple antennas to receive and transmit data. This increases the data transmission rate. 153 Configuring Downlink 64QAM+MIMO This section describes how to activate, verify, and deactivate the optional feature WRFD-010693 DL 64QAM+MIMO. 154 Configuring HSPA+ Uplink 11.5Mbit/s per User This section describes how to activate, verify, and deactivate the optional feature WRFD-010698 HSPA+ Uplink 11.5Mbit/s per User. 155 Configuring HSPA+ Downlink 84 Mbit/s per User This section describes how to activate, verify, and deactivate the optional feature WRFD-010703 HSPA+ Downlink 84 Mbit/s per User. 156 Configuring DC-HSDPA+MIMO This section describes how to activate, verify, and deactivate the optional feature WRFD-010699 DC-HSDPA+MIMO. 157 Configuring UL 16QAM This section describes how to activate, verify, and deactivate the optional feature WRFD-010694 UL 16QAM. 158 Configuring UL Layer 2 Improvement This section describes how to activate, verify, and deactivate the optional feature WRFD-010695 UL Layer 2 Improvement. 159 Configuring DC-HSDPAIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xv


About This Document

This section describes how to activate, verify, and deactivate the optional feature WRFD-010696 DC-HSDPA. 160 Configuring HSPA+ Uplink 23 Mbit/s per User This section describes how to activate, verify, and deactivate the optional feature WRFD-140203 HSPA+ Uplink 23 Mbit/s per User. 161 Configuring DC-HSUPA This section describes how to activate, verify, and deactivate the optional feature WRFD-140204 DC-HSUPA. 162 Configuring Downlink Enhanced CELL_FACH This section describes how to activate, verify, and deactivate the optional feature WRFD-010688 Downlink Enhanced CELL_FACH. 163 Configuring Performance Improvement of MIMO and HSDPA Co-carrier This section describes how to activate, verify, and deactivate the optional feature WRFD-010700 Performance Improvement of MIMO and HSDPA Co-carrier. 164 Configuring CPC - DTX /DRX This section describes how to activate, verify, and deactivate the optional feature WRFD-010686 CPC - DTX /DRX. 165 Configuring CPC - HS-SCCH less operation This section describes how to activate, verify, and deactivate the optional feature WRFD-010687 CPC - HS-SCCH less operation. 166 Configuring E-DPCCH Boosting This section describes how to activate, verify, and deactivate the optional feature WRFD-010697 E-DPCCH Boosting. 167 Configuring Uplink Enhanced CELL_FACH This section describes how to activate, verify, and deactivate the optional feature WRFD-010701 Uplink Enhanced CELL_FACH. 168 Configuring 96 HSDPA Users per Cell This section describes how to activate, verify, and deactivate the optional feature WRFD-010653 96 HSDPA Users per Cell. 169 Configuring 96 HSUPA Users per Cell This section describes how to activate, verify, and deactivate the optional feature WRFD-010639 96 HSUPA Users per Cell. 170 Configuring 128 HSDPA Users per Cell This section describes how to activate, verify, and deactivate the optional feature WRFD-010654 128 HSDPA Users per Cell. 171 Configuring 128 HSUPA Users per Cell This section describes how to activate, verify, and deactivate the optional feature WRFD-010670 128 HSUPA Users per Cell.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xvi


About This Document

172 Configuring Flexible HSPA+ Technology Selection This section describes how to activate, verify, and deactivate the optional feature WRFD-010704 Flexible HSPA+ Technology Selection. 173 Configuring Traffic-Based Activation and Deactivation of the Supplementary Carrier In Multi-carrier This section describes how to activate, verify, and deactivate the optional feature WRFD-010713 Traffic-Based Activation and Deactivation of the Supplementary Carrier In Multi-carrier. 174 Configuring Enhanced DRX This section describes how to activate, verify, and deactivate the optional feature WRFD-010702 Enhanced DRX. (This feature cannot be configured using the CME. ) 175 Configuring Enhanced Fast Dormancy This section describes how to activate, verify, and deactivate the optional feature WRFD-020500 Enhanced Fast Dormancy. (This feature cannot be configured using the CME. ) 176 Configuring Voice Service Experience Improvement for Weak Reception UEs This section describes how to activate, verify, and deactivate the optional feature WRFD-140205 Voice Service Experience Improvement for Weak Reception UEs. 177 Configuring Layered Paging in URA_PCH This section describes how to activate, verify, and deactivate the optional feature WRFD-140206 Layered Paging in URA_PCH. 178 Configuring Web browsing acceleration This section describes how to activate, verify, and deactivate the optional feature WRFD-020132 Web browsing acceleration. (This feature cannot be configured using the CME. ) 179 Configuring P2P Downloading Rate Control during Busy Hour This section describes how to activate, verify, and deactivate the optional feature WRFD-020133 P2P Downloading Rate Control during Busy Hour. (This feature cannot be configured using the CME. ) 180 Configuring Dynamic Power Sharing of Multi-Carriers This section describes how to activate, verify, and deactivate the optional feature WRFD-020116 Dynamic Power Sharing of Multi-Carriers. 181 Configuring Multi-Carrier Switch off Based on Traffic Load This section describes how to activate, verify, and deactivate the optional feature WRFD-020117 Multi-Carrier Switch off Based on Traffic Load. 182 Configuring Energy Efficiency Improved This section describes how to activate, verify, and deactivate the optional feature WRFD-020118 Energy Efficiency Improved. 183 Configuring Multi-Carrier Switch off Based on Power Backup This section describes how to activate, verify, and deactivate the optional feature WRFD-020119 Multi-Carrier Switch off Based on Power Backup.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xvii


About This Document

184 Configuring Multi-Carrier Switch off Based on QoS This section describes how to activate, verify, and deactivate the optional feature WRFD-020122 Multi-Carrier Switch off Based on QoS. 185 Configuring Intelligent Power Management This section describes how to activate, verify, and deactivate the optional feature WRFD-020121 Intelligent Power Management. 186 Configuring RAN Sharing Introduction Package This section describes how to activate, verify and deactivate the optional feature WRFD-021304 RAN Sharing Introduction Package. 187 Configuring Dedicated Carrier for Each Operator This section describes how to activate, verify, and deactivate the optional feature WRFD-02130401 Dedicated Carrier for Each Operator. 188 Configuring Flexible Network Architecture This section describes how to activate, verify, and deactivate the optional feature WRFD-02130402 Flexible Network Architecture. 189 Configuring Mobility Control and Service Differentiation This section describes how to activate, verify, and deactivate the optional feature WRFD02130403 Mobility Control and Service Differentiation. 190 Configuring Independent License Control This section describes how to activate, verify, and deactivate the optional feature WRFD-02130404 Independent License Control. (This feature cannot be configured using the CME. ) 191 Configuring RAN Sharing Phase 2 This section describes how to activate, verify, and deactivate the optional feature WRFD-021305 RAN Sharing Phase 2. 192 Configuring Dedicated Iub Transmission Control This section describes how to activate, verify, and deactivate the optional feature WRFD-02130501 Dedicated Iub Transmission Control. 193 Configuring IMSI Based Handover This section describes how to activate, verify, and deactivate the optional feature WRFD-021303 IMSI Based Handover. 194 Configuring MOCN Introduction Package This section describes how to activate, verify, and deactivate the optional feature WRFD-021311 MOCN Introduction Package. (This feature cannot be configured using the CME. ) 195 Configuring Carrier Sharing by Operators This section describes how to activate, verify, and deactivate the optional feature WRFD-02131101 Carrier Sharing by Operators. 196 Configuring Dedicated NodeB/Cell for OperatorsIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xviii


About This Document

This section describes how to activate, verify, and deactivate the optional feature WRFD-02131102 Dedicated NodeB/Cell for Operators. 197 Configuring MOCN Mobility Management This section describes how to activate, verify, and deactivate the optional feature WRFD-02131103 MOCN Mobility Management. 198 Configuring MOCN Load Balance This section describes how to activate, verify, and deactivate the optional feature WRFD-02131104 MOCN Load Balance. 199 Configuring Routing Roaming UEs in Proportion This section describes how to activate, verify, and deactivate the optional feature WRFD-02131106 Routing Roaming UEs in Proportion. 200 Configuring MOCN Cell Resource Demarcation This section describes how to activate, verify, and deactivate the optional feature WRFD-140223 MOCN Cell Resource Demarcation. 201 Configuring HCS (Hierarchical Cell Structure) This section describes how to activate, verify, and deactivate the optional feature WRFD-021200 HCS (Hierarchical Cell Structure). 202 Configuring One Tunnel This section describes how to activate, verify, and deactivate the optional feature WRFD-020111 One Tunnel. 203 Configuring Overbooking on ATM Transmission This section describes how to activate, verify, and deactivate the optional feature WRFD-050405 Overbooking on ATM Transmission. 204 Configuring ATM Switching-Based Hub NodeB This section describes how to activate, verify, and deactivate the optional feature WRFD-050105 ATM Switching-Based Hub NodeB. 205 Configuring AAL2 Switching-Based Hub NodeB This section describes how to activate, verify, and deactivate the optional feature WRFD-050106 AAL2 Switching-Based Hub NodeB. 206 Configuring IP Transmission Introduction on Iub Interface This section describes how to activate, verify, and deactivate the optional feature WRFD-050402 IP Transmission Introduction on Iub Interface. (This feature cannot be configured using the CME. ) 207 Configuring Hybrid Iub IP Transmission This section describes how to activate, verify and deactivate the optional feature WRFD-050403 Hybrid Iub IP Transmission. 208 Configuring ATM/IP Dual Stack NodeB This section describes how to activate, verify, and deactivate the optional feature WRFD-050404 ATM/IP Dual Stack NodeB.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xix


About This Document

209 Configuring IP Transmission Introduction on Iu Interface This section describes how to activate, verify, and deactivate the optional feature WRFD-050409 IP Transmission Introduction on Iu Interface. 210 Configuring IP Transmission Introduction on Iur Interface This section describes how to activate, verify, and deactivate the optional feature WRFD-050410 IP Transmission Introduction on Iur Interface. 211 Configuring FP MUX for IP Transmission This section describes how to activate, verify, and deactivate the optional feature WRFD-050420 Configuring FP MUX for IP Transmission. 212 Configuring Dynamic Bandwidth Control of Iub IP This section describes how to activate, verify, and deactivate the optional feature WRFD-050422 Dynamic Bandwidth Control of Iub IP. 213 Configuring Overbooking on IP Transmission This section describes how to activate, verify, and deactivate the optional feature WRFD-050408 Overbooking on IP Transmission. 214 Configuring IP Routing-Based Hub NodeB This section describes how to activate, verify, and deactivate the optional feature WRFD-050107 IP Routing-Based Hub NodeB. 215 Configuring PDCP Header Compression (RFC2507) This section describes how to activate, verify, and deactivate the optional feature WRFD-011500 PDCP Header Compression (RFC2507). 216 Configuring RNC Offload This section describes how to activate, verify, and deactivate the optional feature WRFD-012001 RNC Offload. With this feature, the RNC can send some PS service data directly to Internet over the offload Gi interface. 217 Configuring UDP MUX for Iu-CS Transmission This section describes how to activate, verify, and deactivate the feature WRFD-050412 UDP MUX for Iu-CS Transmission. 218 Configuring Iu/Iur Transmission Resource Pool in RNC This section describes how to activate, verify, and deactivate the optional feature WRFD-140207 Iu/Iur Transmission Resource Pool in RNC. 219 Configuring Iub Transmission Resource Pool in RNC This section describes how to activate, verify, and deactivate the optional feature WRFD-140208 Iub Transmission Resource Pool in RNC. 220 Configuring Satellite Transmission on Iub Interface This section describes how to activate, verify, and deactivate the optional feature WRFD-050104 Satellite Transmission on Iub Interface. 221 Configuring Satellite Transmission on Iu InterfaceIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xx


About This Document

This section describes how to activate, verify, and deactivate the optional feature WRFD-050108 Satellite Transmission on Iu Interface. 222 Configuring Clock Synchronization on Ethernet in NodeB This section describes how to activate, verify, and deactivate the optional feature WRFD-050501 Clock Synchronization on Ethernet in NodeB. 223 Configuring Synchronous Ethernet This section describes how to activate, verify, and deactivate the optional feature WRFD-050502 Synchronous Ethernet. 224 Configuring Ethernet OAM This section describes how to activate, verify, and deactivate the optional feature WRFD-050425 Ethernet OAM. (This feature cannot be configured using the CME. ) 225 Configuring RNC Node Redundancy This section describes how to activate, verify, and deactivate the optional feature WRFD-040202 RNC Node Redundancy. 226 Configuring RRU Redundancy This section describes how to activate, verify, and deactivate the optional feature WRFD-040203 RRU Redundancy. 227 Configuring Iu Flex This section describes how to activate, verify, and deactivate the optional feature WRFD-021302 Iu Flex. 228 Configuring Iu Flex Load Distribution Management This section describes how to activate, verify, and deactivate the optional feature WRFD-021306 Iu Flex Load Distribution Management. 229 Configuring Transmit Diversity This section describes how to activate, verify, and deactivate the optional feature WRFD-010203 Transmit Diversity. Transmit diversity enables the NodeB to provide twice the number of RF DL channels compared with no transmit diversity. 230 Configuring 4-Antenna Receive Diversity This section describes how to activate, verify, and deactivate the optional feature WRFD-010209 4-Antenna Receive Diversity. 231 Configuring Extended Cell Coverage up to 200km This section describes how to activate, verify, and deactivate the optional feature WRFD-021308 Extended Cell Coverage up to 200km. 232 Configuring HSUPA Coverage Enhancement at UE Power Limitation This section describes how to activate, verify, and deactivate the optional feature WRFD-020138 HSUPA Coverage Enhancement at UE Power Limitation. 233 Configuring Flexible frequency bandwidth of UMTS carrier This section describes how to activate, verify, and deactivate the optional feature WRFD-021001 Flexible frequency bandwidth of UMTS carrier.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxi


About This Document

234 Configuring High Speed Access This section describes how to activate, verify, and deactivate the optional feature WRFD-010206 High Speed Access. 235 Configuring Independent Demodulation of Signals from Multiple RRUs in One Cell This section describes how to activate, verify, and deactivate the optional feature WRFD-021350 Independent Demodulation of Signals from Multiple RRUs in One Cell. 236 Configuring Inter Frequency Hard Handover Based on Coverage This section describes how to activate, verify, and deactivate the optional feature WRFD-020302 Inter Frequency Hard Handover Based on Coverage. 237 Configuring Inter Frequency Hard Handover Based on DL QoS This section describes how to activate, verify, and deactivate the optional feature WRFD-020304 Inter Frequency Hard Handover Based on DL QoS. 238 Configuring SRNS Relocation (UE Not Involved) This section describes how to activate, verify, and deactivate the optional feature WRFD-02060501 SRNS Relocation (UE Not Involved). (This feature cannot be configured using the CME. ) 239 Configuring SRNS Relocation with Hard Handover This section describes how to activate, verify, and deactivate the optional feature WRFD-02060502 SRNS Relocation with Hard Handover. 240 Configuring SRNS Relocation with Cell/URA Update This section describes how to activate, verify, and deactivate the optional feature WRFD-02060503 SRNS Relocation with Cell/URA Update. 241 Configuring Multiple RAB Package (PS RAB 2) This section describes how to activate, verify, and deactivate the optional feature WRFD-010615 Multiple RAB Package (PS RAB 2). 242 Configuring Combination of Two PS Services This section describes how to activate, verify, and deactivate the optional feature WRFD-01061501 Combination of Two PS Services. 243 Configuring Combination of One CS Service and Two PS Services This section describes how to activate, verify, and deactivate the optional feature WRFD-01061502 Combination of One CS Service and Two PS Services. 244 Configuring Combination of Three PS Services This section describes how to activate, verify, and deactivate the optional feature WRFD-01061503 Combination of Three PS Services. 245 Configuring Combination of One CS Service and Three PS Services This section describes how to activate, verify, and deactivate the optional feature WRFD-01061504 Combination of One CS Service and Three PS Services. 246 Configuring Combination of Four PS ServicesIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxii


About This Document

This section describes how to activate, verify, and deactivate the optional feature WRFD-01061505 Combination of Four PS Services. 247 Configuring Inter Frequency Load Balance This section describes how to activate, verify, and deactivate the optional feature WRFD-020103 Inter Frequency Load Balance. 248 Configuring Domain Specific Access Control (DSAC) This section describes how to activate, verify, and deactivate the optional feature WRFD-020114 Domain Specific Access Control (DSAC). 249 Configuring Enhanced Multiband Management This section describes how to activate, verify, and deactivate the optional feature WRFD-020160 Enhanced Multiband Management. 250 Configuring DRD Introduction Package This section describes how to activate, verify, and deactivate the optional feature WRFD-020400 DRD Introduction Package. 251 Configuring Intra System Direct Retry This section describes how to activate, verify, and deactivate the optional feature WRFD-02040001 Intra System Direct Retry. 252 Configuring Inter System Direct Retry This section describes how to activate, verify, and deactivate the optional feature WRFD-02040002 Inter System Direct Retry. 253 Configuring Inter-System Redirect This section describes how to activate, verify, and deactivate the optional feature WRFD-02040003 Inter System Redirect. 254 Configuring Traffic Steering and Load Sharing During RAB Setup This section describes how to activate, verify, and deactivate the optional feature WRFD-02040004 Traffic Steering and Load Sharing During RAB Setup. 255 Configuring Measurement Based Direct Retry This section describes how to activate, verify, and deactivate the optional feature WRFD-020402 Measurement Based Direct Retry. 256 Configuring Service Steering and Load Sharing in RRC Connection Setup This section describes how to activate, verify, and deactivate the optional feature WRFD-020120 Service Steering and Load Sharing in RRC Connection Setup. 257 Configuring Uplink Flow Control of User Plane This section describes how to activate, verify, and deactivate the optional feature WRFD-020124 Uplink Flow Control of User Plane. 258 Configuring Intra Frequency Load Balance This section describes how to activate, verify, and deactivate the optional feature WRFD-020104 Intra Frequency Load Balance.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxiii


About This Document

259 Configuring Dynamic Target ROT Adjustment This section describes how to activate, verify, and deactivate the optional feature WRFD-140211 Dynamic Target RoT Adjustment. 260 Configuring CE Overbooking This section describes how to activate, verify, and deactivate the optional feature WRFD-140212 CE Overbooking. 261 Configuring Intelligent Access Class Control This section describes how to activate, verify, and deactivate the optional feature WRFD-140213 Intelligent Access Class Control. 262 Configuring Dynamic Configuration of HSDPA CQI Feedback Period This section describes how to activate, verify, and deactivate the optional feature WRFD-140215 Dynamic Configuration of HSDPA CQI Feedback Period. 263 Configuring Load-based Uplink Target BLER Configuration This section describes how to activate, verify, and deactivate the optional feature WRFD-140216 Load-based Uplink Target BLER Configuration. 264 Configuring Inter-Frequency Load Balancing Based on Configurable Load Threshold This section describes how to activate, verify, and deactivate the optional feature WRFD-140217 Inter-Frequency Load Balancing Based on Configurable Load Threshold. 265 Configuring Load Based GSM and UMTS Handover Enhancement Based on Iur-g This section describes how to activate, verify, and deactivate the optional feature WRFD-070004 Load Based GSM and UMTS Handover Enhancement Based on Iur-g. 266 Configuring NACC(Network Assisted Cell Change) Procedure Optimization Based on Iur-g This section describes how to activate, verify, and deactivate the optional feature WRFD-070005 NACC Procedure Optimization Based on Iur-g. 267 Configuring GSM and UMTS Load Balancing Based on Iur-g This section describes how to activate, verify, and deactivate the optional feature WRFD-070006 GSM and UMTS Load Balancing Based on Iur-g. 268 Configuring GSM and UMTS Traffic Steering Based on Iur-g This section describes how to activate, verify, and deactivate the optional feature WRFD-070007 GSM and UMTS Traffic Steering Based on Iur-g. 269 Configuring Inter-RAT Handover Based on Coverage This section describes how to activate, verify, and deactivate the optional feature WRFD-020303 Inter-RAT Handover Based on Coverage. 270 Configuring Inter-RAT Handover Based on DL QoS This section describes how to activate, verify, and deactivate the optional feature WRFD-020309 Inter-RAT Handover Based on DL QoS. 271 Configuring Video Telephony Fallback to Speech (AMR) for Inter-RAT HOIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxiv


About This Document

This section describes how to activate, verify, and deactivate the optional feature WRFD-020307 Video Telephony Fallback to Speech (AMR) for Inter-RAT HO. 272 Configuring Inter-RAT Handover Phase 2 This section describes how to activate, verify, and deactivate the optional feature WRFD-020308 Inter-RAT Handover Phase 2. 273 Configuring NACC(Network Assisted Cell Change) This section describes how to activate, verify, and deactivate the optional feature WRFD-02030801 NACC(Network Assisted Cell Change). 274 Configuring PS Handover between UMTS and GPRS This section describes how to activate, verify, and deactivate the optional feature WRFD-02030802 PS Handover between UMTS and GPRS. 275 Configuring Inter-RAT Handover Based on Service This section describes how to activate, verify, and deactivate the optional feature WRFD-020305 Inter-RAT Handover Based on Service. 276 Configuring Inter-RAT Handover Based on Load This section describes how to activate, verify, and deactivate the optional feature WRFD-020306 Inter-RAT Handover Based on Load. 277 Configuring Inter-RAT Redirection Based on Distance This section describes how to activate and verify the optional feature WRFD-020401 Inter-RAT Redirection Based on Distance. 278 Configuring 3G/2G Common Load Management This section describes how to activate, verify, and deactivate the optional feature WRFD-020310 3G/2G Common Load Management. 279 Configuring Mobility Between UMTS and LTE Phase 1 This section describes how to activate, verify, and deactivate the optional feature WRFD-020126 Mobility Between UMTS and LTE Phase 1. For details about how to configure this feature on the LTE side, see the related documents provided by the LTE equipment vendor. (This feature cannot be configured using the CME. ) 280 Configuring Service-Based PS Service Redirection from UMTS to LTE This section describes how to activate, verify, and deactivate the optional feature WRFD-020129 Service-Based PS Service Redirection from UMTS to LTE. 281 Configuring Service-Based PS Handover from UMTS to LTE This section describes how to activate, verify, and deactivate the optional feature WRFD-140218 Service-Based PS Handover from UMTS to LTE. 282 Configuring Fast CS Fallback Based on RIM This section describes how to activate, verify, and deactivate the basic feature WRFD-140224 fast CS fallback based on RIM. For details about how to configure this feature on the LTE side, see the related documents provided by the LTE equipment vendor. 283 Configuring Queuing and PreemptionIssue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxv


About This Document

This section describes how to activate, verify, and deactivate the optional feature WRFD-010505 Queuing and Preemption. 284 Configuring Access Class Restriction This section describes how to activate, verify, and deactivate the optional feature WRFD-021103 Access Class Restriction. 285 Configuring Traffic Priority Mapping onto Transmission Resources This section describes how to activate, verify, and deactivate the optional feature WRFD-050424 Traffic Priority Mapping onto Transmission Resources. 286 Configuring Differentiated Service Based on SPI Weight This section describes how to activate, verify, and deactivate the optional feature WRFD-020806 Differentiated Service Based on SPI Weight. 287 Configuring Optimization of R99 and HSUPA Users Fairness This section describes how to activate, verify, and deactivate the optional feature WRFD-020131 Optimization of R99 and HSUPA Users Fairness. 288 Configuring Active Queue Management (AQM) This section describes how to activate, verify, and deactivate the optional feature WRFD-011502 Active Queue Management (AQM). 289 Configuring Quality Improvement for Subscribed Service This section describes how to activate, verify, and deactivate the optional feature WRFD-020128 Quality Improvement for Subscribed Service. 290 Configuring TCP Accelerator This section describes how to activate, verify, and deactivate the optional feature WRFD-020123 TCP Accelerator. 291 Configuring Rate Negotiation at Admission Control This section describes how to activate, verify, and deactivate the optional feature WRFD-010507 Rate Negotiation at Admission Control. 292 Configuring Videophone Service Restriction This section describes how to activate, verify, and deactivate the optional feature WRFD-020130 Videophone Service Restriction. 293 Configuring Intelligent Inter-Carrier UE Layered Management This section describes how to activate, verify, and deactivate the optional feature WRFD-020135 Intelligent Inter-Carrier UE Layered Management. 294 Configuring Micro NodeB Self-Planning This section describes how to activate, verify, and deactivate the optional feature WRFD-140219 Micro NodeB Self-Planning. 295 Configuring NodeB Integrated IPSec This section describes how to activate, verify, and deactivate the optional feature WRFD-140209 NodeB Integrated IPSec.Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxvi


About This Document

296 Configuring NodeB PKI Support This section describes how to activate, verify, and deactivate the optional feature WRFD-140210 NodeB PKI Support. (This feature cannot be configured using the CME. ) 297 Configuring Intelligent Battery Management This section describes how to activate, verify, and deactivate the optional feature WRFD-140220 Intelligent Battery Management. (This feature cannot be configured using the CME. ) 298 Configuring Multi-mode Dynamic Power Sharing (UMTS) This section describes how to activate, verify, and deactivate the optional feature MRFD-221801 Multi-mode Dynamic Power Sharing (UMTS). 299 Configuring GSM and UMTS Dynamic Spectrum Sharing (UMTS) This section describes how to activate, verify, and deactivate the optional feature MRFD-221802 GSM and UMTS Dynamic Spectrum Sharing (UMTS). This feature enables the spectrum resources to be dynamically shared between the GSM and UMTS networks based on their traffic load, improving frequency utilization. 300 Configuring IP-Based Multi-Mode Co-Transmission on Base Station Side (NodeB) This section describes how to activate, verify, and deactivate the optional feature MRFD-221501 IP-Based Multi-Mode Co-Transmission on Base Station Side. For details about data configurations, see section Configuration Reference > MBTS Configuration Reference (V100R007C00) > Common Transmission in the 3900 Series Base Station Initial Configuration Guide, or see section Common Transmission in the WCDMA RAN Feature Documentation. The latest 3900 Series Base Station Initial Configuration Guide can be obtained from the following path: HUAWEI Technical Support (support.huawei.com), Support > Documentation > SingleRAN > MBTS > SingleRAN7.0. 301 Configuring TDM-Based Multi-mode Co-Transmission via Backplane on BS side (NodeB) This section describes how to activate, verify, and deactivate the optional feature MRFD-221504 TDM-Based Multi-mode Co-Transmission via Backplane on BS side (NodeB). (This feature cannot be configured using the CME. ) 302 Configuring Multi-Mode BS Common Reference Clock (NodeB) This section describes how to activate, verify, and deactivate the optional feature MRFD-221601 Multi-Mode BS Common Reference Clock (NodeB). For details about data configurations, see section Configuration Reference > MBTS Configuration Reference (V100R007C00) > Common Clock in the 3900 Series Base Station Initial Configuration Guide, or see section Common Clock in the WCDMA RAN Feature Documentation. The latest 3900 Series Base Station Initial Configuration Guide can be obtained from the following path: HUAWEI Technical Support (support.huawei.com), Support > Documentation > SingleRAN > MBTS > SingleRAN7.0. 303 Multi-mode BS Common IPSec(UMTS) This section describes how to activate, verify, and deactivate the multi-mode feature MRFD-221602 Multi-mode BS Common IPSec(UMTS). 304 Configuring 2.0MHz Central Frequency point separation between GSM and UMTS mode(UMTS)Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxvii


About This Document

This section describes how to activate, verify, and deactivate the optional feature MRFD-221703 2.0MHz Central Frequency point separation between GSM and UMTS mode(UMTS). 305 Configuring Dynamic MA for GU Dynamic Spectrum Sharing (UMTS) This section describes how to activate, verify, and deactivate the multi-mode feature MRFD-221803 Dynamic MA for GU Dynamic Spectrum Sharing(UMTS). 306 Configuring GSM Power Control on Interface Frequency for GU Small Frequency Gap (UMTS) This section describes how to activate, verify, and deactivate the multi-mode feature MRFD-221804 GSM Power Control on Interference Frequency for GU Small Frequency gap (UMTS).

ConventionsSymbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazard with a high level or medium level of risk which, if not avoided, could result in death or serious injury. Indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Indicates a potentially hazardous situation that, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results. Indicates a tip that may help you solve a problem or save time. Provides additional information to emphasize or supplement important points of the main text.

General Conventions The general conventions that may be found in this document are defined as follows. Convention Times New Roman Boldface Italic Courier New Description Normal paragraphs are in Times New Roman. Names of files, directories, folders, and users are in boldface. For example, log in as user root. Book titles are in italics. Examples of information displayed on the screen are in Courier New.xxviii

Issue 05 (2012-12-31)



About This Document

Command Conventions The command conventions that may be found in this document are defined as follows. Convention Boldface Italic [] { x | y | ... } [ x | y | ... ] { x | y | ... }* Description The keywords of a command line are in boldface. Command arguments are in italics. Items (keywords or arguments) in brackets [ ] are optional. Optional items are grouped in braces and separated by vertical bars. One item is selected. Optional items are grouped in brackets and separated by vertical bars. One item is selected or no item is selected. Optional items are grouped in braces and separated by vertical bars. A minimum of one item or a maximum of all items can be selected. Optional items are grouped in brackets and separated by vertical bars. Several items or no item can be selected.

[ x | y | ... ]*

GUI Conventions The GUI conventions that may be found in this document are defined as follows. Convention Boldface > Description Buttons, menus, parameters, tabs, window, and dialog titles are in boldface. For example, click OK. Multi-level menus are in boldface and separated by the ">" signs. For example, choose File > Create > Folder.

Keyboard Operations The keyboard operations that may be found in this document are defined as follows. Format Key Key 1+Key 2 Key 1, Key 2 Description Press the key. For example, press Enter and press Tab. Press the keys concurrently. For example, pressing Ctrl+Alt +A means the three keys should be pressed concurrently. Press the keys in turn. For example, pressing Alt, A means the two keys should be pressed in turn.

Issue 05 (2012-12-31)


xxix


About This Document

Mouse Operations The mouse operations that may be found in this document are defined as follows. Action Click Double-click Drag Description Select and release the primary mouse button without moving the pointer. Press the primary mouse button twice continuously and quickly without moving the pointer. Press and hold the primary mouse button and move the pointer to a certain position.

Issue 05 (2012-12-31)


xxx


Contents

ContentsAbout This Document.....................................................................................................................ii 1 Changes in the RAN Feature Activation Guide......................................................................1 2 Feature Activation and License Item Descriptions...............................................................10 3 Overview of Configurations on the CME...............................................................................543.1 Introduction to Configuration Methods............................................................................................................56 3.2 Configuring Device Data..................................................................................................................................57 3.3 Introduction to the Configuration Express for UMTS Global Parameters.......................................................58 3.4 Introduction to the Configuration Express for Iub Interfaces...........................................................................59 3.5 Introduction to the Configuration Express for Iu-CS Interfaces......................................................................60 3.6 Introduction to the Configuration Express for Iu-PS Interfaces.......................................................................61 3.7 Introduction to the Configuration Express for Iur Interfaces...........................................................................62 3.8 Introduction to the Configuration Express for Iu-BC Interfaces......................................................................63 3.9 Introduction to the Configuration Express for Iu-PC Interfaces......................................................................64 3.10 Introduction to the Configuration Express for the (U)Iur-g Interface............................................................65 3.11 Introduction to the Configuration Express for Gi Interfaces..........................................................................66 3.12 Introduction to the Configuration Express for UMTS Global Radio Parameters..........................................67 3.13 Introduction to the Configuration Express for UMTS Cells..........................................................................68 3.14 Introduction to the Configuration Express for Neighboring UMTS Cells.....................................................69 3.15 Modifying RNC Parameters in Batches.........................................................................................................70 3.16 Modifying Logical NodeB Parameters in Batches.........................................................................................70 3.17 Modifying Physical NodeB Parameters in Batches........................................................................................71 3.18 Modifying UMTS Cell Parameters in Batches...............................................................................................71 3.19 Modifying RNC External Cell Parameters in Batches...................................................................................72 3.20 Modifying UMTS Channel Parameters in Batches........................................................................................73 3.21 Introduction to the Object Group Configuration............................................................................................74

4 Activating the UMTS License...................................................................................................764.1 Activating the BSC6900 License.....................................................................................................................77 4.2 Allocating a license to Telecom Operators.......................................................................................................78 4.3 Allocating a License to NodeBs.......................................................................................................................78

5 Configuring 3.4/6.8/13.6/27.2Kbps RRC Connection and Radio Access Bearer Establishment and Release...........................................................................................................80Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxxi


Contents

6 Configuring Conversational QoS Class .................................................................................83 7 Configuring Streaming QoS Class...........................................................................................86 8 Configuring Interactive QoS Class..........................................................................................89 9 Configuring Background QoS Class.......................................................................................91 10 Configuring Emergency Call...................................................................................................93 11 Configuring RAB Quality of Service Renegotiation over Iu Interface...........................94 12 Configuring 2-Way Antenna Receive Diversity..................................................................97 13 Configuring Cell Digital Combination and Split...............................................................99 14 Configuring UE State in Connected Mode (CELL_DCH, CELL_PCH, URA_PCH, CELL_FACH).................................................................................................................................102 15 Configuring Paging UE in Idle, CELL_PCH, URA_PCH State (Type 1)......................105 16 Configuring Paging UE in CELL_FACH, CELL_DCH State (Type 2)...........................109 17 Configuring Dynamic Channel Configuration Control..................................................111 18 Configuring Integrity Protection..........................................................................................120 19 Configuring Encryption.........................................................................................................122 20 Configuring Open Loop Power Control.............................................................................124 21 Configuring Downlink Power Balance...............................................................................127 22 Configuring Outer Loop Power Control.............................................................................129 23 Configuring Inner Loop Power Control .............................................................................132 24 Configuring Admission Control..........................................................................................134 25 Configuring Load Measurement..........................................................................................138 26 Configuring Load Reshuffling.............................................................................................140 27 Configuring Overload Control.............................................................................................144 28 Configuring Code Resource Management.........................................................................147 29 Configuring Potential User Control.....................................................................................149 30 Configuring Cell Barring.......................................................................................................151 31 Configuring Shared Network Support in Connected Mode..........................................156 32 Configuring Intra NodeB Softer Handover........................................................................159 33 Configuring Intra RNC Soft Handover...............................................................................161 34 Configuring Inter RNC Soft Handover...............................................................................163 35 Configuring Intra Frequency Hard Handover...................................................................165Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxxii


Contents

36 Configuring Intra RNC Cell Update....................................................................................168 37 Configuring Inter RNC Cell Update....................................................................................171 38 Configuring Intra RNC URA Update..................................................................................173 39 Configuring Inter RNC URA Update..................................................................................176 40 Configuring Direct Signaling Connection Re-establishment (DSCR) ........................179 41 Configuring CS Fallback Guarantee for LTE Emergency Calls.....................................182 42 Configuring NodeB Clock.....................................................................................................184 43 Configuring Dynamic AAL2 Connections in Iub/IuCS/Iur Interface...........................188 44 Configuring Permanent AAL5 Connections for Control Plane Traffic........................190 45 Configuring Call Admission Based on Used AAL2 Path Bandwidth...........................192 46 Configuring CBR, rt-VBR, nrt-VBR, UBR ATM QoS Classes........................................194 47 Configuring F5.........................................................................................................................196 48 Configuring UBR+ ATM QoS Class....................................................................................198 49 Configuring Link Aggregation.............................................................................................200 50 Configuring Flow Control.....................................................................................................204 51 Configuring BOOTP...............................................................................................................209 52 Configuring NodeB Self-Discovery Based on IP Mode..................................................211 53 Configuring License Control for Urgency..........................................................................215 54 Configuring Intelligently Out of Service...........................................................................217 55 Configuring OCNS.................................................................................................................219 56 Configuring Power Off the Equipment Level by Level...................................................221 57 Configuring Solar Power Device Management.................................................................224 58 Configuring Connection with TMA (Tower Mounted Amplifier)................................226 59 Configuring Remote Electrical Tilt......................................................................................229 60 Configuring Same Band Antenna Sharing Unit (900 MHz)...........................................232 61 Configuring VoIP over HSPA/HSPA+................................................................................235 62 Configuring Optimized Scheduling for VoIP over HSPA..............................................241 63 Configuring IMS Signaling over HSPA.............................................................................243 64 Configuring PDCP Header Compression (RoHC)............................................................246 65 Configuring CS Voice over HSPA/HSPA+........................................................................249Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxxiii


Contents

66 Configuring AMR-WB (Adaptive Multi Rate Wide Band).............................................254 67 Configuring AMR/WB-AMR Speech Rates Control........................................................257 68 Configuring TFO/TrFO..........................................................................................................262 69 Configuring AMR Voice Quality Improvement Based on PLVA.................................264 70 Configuring Cell Broadcast Service.....................................................................................266 71 Configuring Simplified Cell Broadcast..............................................................................276 72 Configuring Warning of Disaster.........................................................................................279 73 Configuring MBMS Introduction Package........................................................................281 74 Configuring MBMS Admission Control............................................................................285 75 Configuring MBMS Load Control.......................................................................................287 76 Configuring MBMS Transport Resource Management...................................................289 77 Configuring Streaming Service on MBMS........................................................................291 78 Configuring 16/32/64/128Kbps Channel Rate on MBMS.................................................293 79 Configuring MBMS Phase 2..................................................................................................295 80 Configuring MBMS Enhanced Broadcast Mode...............................................................297 81 Configuring MBMS P2P over HSDPA................................................................................299 82 Configuring MBMS Admission Enhancement.................................................................301 83 Configuring Inter-Frequency Neighboring Cell Selection for MBMS PTP Users ..........................................................................................................................................................303 84 Configuring FACH Transmission Sharing for MBMS....................................................304 85 Configuring MBMS FLC(Frequency Layer Convergence)/FLD(Frequency Layer Dispersion) ....................................................................................................................................306 86 Configuring MBMS over Iur.................................................................................................309 87 Configuring Dynamic Power Estimation for MTCH.......................................................311 88 Configuring MSCH Scheduling...........................................................................................313 89 Configuring MBMS Channel Audience Rating Statistics...............................................315 90 Configuring Cell ID + RTT Function Based LCS.............................................................317 91 Configuring OTDOA Based LCS.........................................................................................325 92 Configuring A-GPS Based LCS............................................................................................328 93 Configuring LCS Classified Zones......................................................................................336 94 Configuring LCS over Iur......................................................................................................339Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxxiv


Contents

95 Configuring Iupc Interface for LCS Service.......................................................................346 96 Configuring Push to Talk......................................................................................................349 97 Configuring HSUPA Introduction Package.......................................................................351 98 Configuring HSUPA Admission Control...........................................................................354 99 Configuring HSUPA Power Control ..................................................................................358 100 Configuring HSUPA Mobility Management...................................................................361 101 Configuring HSUPA DCCC................................................................................................363 102 Configuring 20 HSUPA Users per Cell.............................................................................366 103 Configuring HSUPA Iub Flow Control in Case of Iub Congestion............................368 104 Configuring HSUPA E-AGCH Power Control (Based on CQI or HS-SCCH)...........370 105 Configuring HSUPA 2ms TTI.............................................................................................372 106 Configuring HSUPA 2 ms/10 ms TTI Handover.............................................................375 107 Configuring HSUPA 5.74Mbps per User..........................................................................377 108 Configuring Streaming Traffic Class on HSUPA...........................................................380 109 Configuring HSUPA over Iur.............................................................................................382 110 Configuring TTI Switch for BE Services Based on Coverage.......................................384 111 Configuring HSUPA Adaptive Transmission.................................................................388 112 Configuring Dynamic CE Resource Management..........................................................391 113 Configuring HSUPA FDE....................................................................................................393 114 Configuring Adaptive Configuration of Traffic Channel Power offset for HSUPA ..........................................................................................................................................................395 115 Configuring Anti-Interference Scheduling for HSUPA................................................403 116 Configuring Dual-Threshold Scheduling with HSUPA Interference Cancellation ..........................................................................................................................................................407 117 Configuring 60 HSUPA Users per Cell.............................................................................411 118 Configuring HSUPA UL Interference Cancellation.......................................................413 119 Configuring SRB over HSUPA...........................................................................................416 120 Configuring Control Channel Parallel Interference Cancellation (Phase 2).............418 121 Configuring HSDPA Introduction Package.....................................................................423 122 Configuring 15 Codes per Cell............................................................................................426 123 Configuring Time and HS-PDSCH Codes Multiplex....................................................429Issue 05 (2012-12-31) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. xxxv


Contents

124 Configuring HSDPA H-ARQ & Scheduling (MAX C/I, RR, and PF).........................430 125 Configuring HSDPA Static Code Allocation and RNC-Controlled Dynamic Code Allocation.......................................................................................................................................432 126 Configuring HSDPA Power Control ................................................................................434 127 Configuring HSDPA Admission Control.........................................................................437 128 Configuring Improvement of User Experience in Low Traffic Service......................440 129 Configuring HSDPA Flow Control....................................................................................442 130 Configuring HSDPA Mobility Management...................................................................445 131 Configuring HSDPA UE Category 1 to 28........................................................................447 132 Configuring DL 16QAM Modulation...............................................................................448 133 Configuring Dynamic Code Allocation Based on NodeB.............................................450 134 Configuring HSDPA Enhanced Package..........................................................................454 135 Configuring Scheduling based on EPF and GBR...........................................................456 136 Configuring HSDPA State Transition.................................................................

RAN14.0 Feature Activation Guide

Documents

Transcript of RAN14.0 Feature Activation Guide