Radar - kontram.fi · 14 Radar – VEGAPULS VEGAPULS Non-contact measurement under arduous process...
Transcript of Radar - kontram.fi · 14 Radar – VEGAPULS VEGAPULS Non-contact measurement under arduous process...
1313Radar – VEGAPULS
RadarOverview 14
VEGAPULSseries60 18
14 Radar – VEGAPULS
VEGAPULSNon-contactmeasurementunderarduousprocessconditionsMeasuringprincipleExtremely short microwave impulses are emitted by the antenna systemto the measured product, reflected by the product surface and receivedagain by the antenna system. They spread with light velocity and the timefrom emission to reception of the signals is proportional to the level in thevessel. A special time spreading procedure enables the reliable andprecise measurement of the extremely short times. The radar sensorswork with low emitted power in the C and K-band frequency range. Theproven ECHOFOX signal processing selects the correct level echoreliably from a number of false reflections. An adjustment with empty andfull vessel is not necessary.
ApplicationsinliquidsTwo different emitting frequencies are available for these applications.The compact, high frequency K-band sensors VEGAPULS 61, 62 and 63 are particularly suitable for applications for which high accuracy is required. Even with small antenna sizes, an excellent signal focusing is reached. The low frequency C-band sensors VEGAPULS 65 and 66 can penetrate foam and strong condensation and are thus particularly suitable for arduous process conditions. Unaffected by steam, gas composition, pressure and temperature changes the sensors detect the product surface of different products reliably.
ApplicationsinbulksolidsThe high frequency sensors VEGAPULS 67 and 68 in K-band technology are used for these applications. Thanks to the very good focusing of the signals, the influences of silo installations or buildup on the vessel wall are gated out. A high sensitivity electronics adapted to the requirements of the bulk solids measurement, enables a reliable level measurement of differentproducts up to 75 m. The measuring principle is unaffected by strong dustgeneration, filling noise, air turbulence by pneumatic filling andtemperature fluctuations. The application area covers applications in thefood processing industry and the plastic processing up to the steelgeneration and mineral rock processing.
Radar – VEGAPULS
151515
Overview–Radarsensorsforliquids
Radar – VEGAPULS
VEGAPULS63 VEGAPULS65 VEGAPULS66
Application Aggressive liquids under arduous process conditions
Aggressive liquids under easy process conditions
Storage tanks and process vessels under arduous process conditions
Measuringrange up to 35 m up to 35 m up to 35 m
Processfitting Flange, hygienic fitting Thread G1½ A, flange Flange
Processtemperature -200 … +200 °C -40 … +150 °C -60 … +400 °C
Processpressure -1 … +16 bar (-100 … +1600 kPa)
-1 … +16 bar (-100 … +1600 kPa)
-1 … +160 bar (-100 … +16000 kPa)
Accuracy +/- 2 mm +/- 8 mm +/- 8 mm
VEGAPULSWL61 VEGAPULS61 VEGAPULS62
Application Liquids, mainly in the water and sewage management
Aggressive liquids in vessels under easy process conditions
Storage tanks and process vessels under arduous process conditions
Measuringrange up to 15 m up to 35 m up to 35 m
Processfitting Mounting strap, thread G1½ A, flange
Thread G1½ A, mounting strap, flange
Thread, flange
Processtemperature -40 … +80 °C -40 … +80 °C -200 … +450 °C
Processpressure -1 … +2 bar (-100 … +200 kPa)
-1 … +3 bar (-100 … +300 kPa)
-1 … +160 bar (-100 … +16000 kPa)
Accuracy +/- 2 mm +/- 2 mm +/- 2 mm
Overview–Radarsensorsforliquids
Radar – VEGAPULS
161616
Overview–Radarsensorsforbulksolids
Radar – VEGAPULS
VEGAPULS67 VEGAPULSSR68 VEGAPULS68
Application Bulk solids Bulk solids Bulk solids under arduous process conditions
Measuringrange up to 15 m up to 30 m up to 75 m
Processfitting Mounting strap, flange Thread G1½ A, flange Thread G1½ A, flange
Processtemperature -40 … +80 °C -40 … +250 °C -200 … +450 °C
Processpressure -1 … +2 bar (-100 … +200 kPa)
-1 … +100 bar (-100 … +10000 kPa)
-1 … +160 bar (-100 … +16000 kPa)
Accuracy +/- 2 mm +/- 2 mm +/- 2 mm
171717Radar – VEGAPULS
18
2
1
15 m
m(0
.59"
)98
mm
(3.8
6")
300
mm
(11.
81")
42,5
mm
(1.6
7")
18,5
mm
(0.7
3")
19 m
m(0
.75"
)
ø 75 mm(2.95")
ø 72 mm(2.84")
ø 8 mm(0.32")
G1 1/2
ø 115 mm(4.53")
Radar – VEGAPULS WL61
1 Mounting strap2 Adapter flange
You will find further process fittings and options under www.vega.com/configuratorYou will find further drawings and tables under www.vega.com/downloadsYou will find mounting accessory and welded sockets in chapter "Accessory"
VEGAPULS WL61
Radar sensor for continuous level measurement
Application areaThe radar sensor VEGAPULS WL61 is particularly suitable for use in water processing, pump stations, overflow basins, for flow measurement in open flumes and gauge monitoring.
AdvantagesNon-contact measurementSimple mountingHigh protection IP 68 (1 bar)Wear and maintenance-freeUnaffected by pressure, temperature, vapour and fogHigh accuracy
FunctionExtremely short microwave pulses are emitted via the antenna system to the measured product, reflected by the product surface and received again by the antenna system. The time from emission to reception of the signals is proportional to the level.
19Radar – VEGAPULS WL61
basic price:
ApprovalXX without ...............................................................................................................................................................AX ATEX II 3G Ex nA II T5...T1 X ...........................................................................................................................CX ATEX II 1G, 1/2G, 2G Ex ia IIC T6 Ga, Ga/Gb, Gb ..........................................................................................
Version / Material / Process temperatureB with plastic horn antenna ø80mm / PP / -40...80°C ....................................................................................
Process fitting / MaterialXX without compression flange ................................................................................................................XC Mounting strap 170mm / 1.4404 .........................................................................................................XD Mounting strap 300 mm / 1.4404 ........................................................................................................
ElectronicsH Two-wire 4...20mA/HART® ..........................................................................................................P Profibus PA ..................................................................................................................................F Foundation Fieldbus .....................................................................................................................
Housing / ProtectionK Plastic / IP68(1bar) / with cable outlet ....................................................................................
Cable / Material / TemperatureA 6 m suspension cable(can be shortened)/ PUR / -40...80° ..............................................T selectable length / PUR / -40...80°C ................................................................................
Additonal equipmentX without ........................................................................................................................
PSWL61.
Cable lengthfrom 5 m, per additional 100 mm cable of PUR
202020
2
4
3
1
43 m
m(1
.69"
)20
mm
(0.7
9")
78 m
m (3
.07"
)
ø 39 mm(1.54")
SW 50 mm(1.97")
G1½ A
15 m
m(0
.59"
)98
mm
(3.8
6")
170
mm
/ 30
0 m
m(6
.69"
) / (
11.8
1")
19 m
m(0
.75"
)
ø 75 mm(2.95")
ø 115 mm(4.53")
1 Version with encapsulated antenna system
2 Version with plastic horn antenna3 Mounting strap4 Adapter flange
You will find further process fittings and options under www.vega.com/configuratorYou will find further drawings and tables under www.vega.com/downloadsYou will find mounting accessory and welded sockets in chapter "Accessory"
Radar – VEGAPULS 61
VEGAPULS 61
Radar sensor for continuous level measurement
Application areaVEGAPULS 61 is suitable for applications in liquids in vessels under easy process conditions. The application possibilities can be found in virtually all industries.
AdvantagesNon-contact measurementSimple mountingWear and maintenance-freeUnaffected by pressure, temperature, gas and vapourHigh measuring accuracySIL qualified
FunctionExtremely short microwave pulses are emitted via the antenna system to the measured product, reflected by the product surface and received again by the antenna system. The time from emission to reception of the signals is proportional to the level. A special evaluation procedure ensures a reliable and precise measurement.
2121Radar – VEGAPULS 61
basic price:
ApprovalXX without ................................................................................................................................................................XM Ship approval ......................................................................................................................................................CX ATEX II 1G, 1/2G, 2G Ex ia IIC T6 .....................................................................................................................CA ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + WHG ........................................................................................................CM ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + Ship approval ...........................................................................................CI IEC Ex ia IIC T6 ..................................................................................................................................................
DX ATEX II 1/2G, 2G Ex d ia IIC T5/T6 ...................................................................................................................DI IEC Ex d ia IIC T6 ...............................................................................................................................................
Version / Material / Process temperatureA with encapsulated horn antenna ø40mm / PVDF / -40..80°C ......................................................................B with plastic horn antenna ø80mm / PP / -40...80°C .....................................................................................
Process fitting / MaterialXX without compression flange ................................................................................................................GP Thread G1½A PN3 / PVDF .................................................................................................................NP Thread 1½NPT PN3 / PVDF ...............................................................................................................CA Tri-Clamp 2" PN3 / 316L .....................................................................................................................CB Tri-Clamp 3" PN3 / 316L .....................................................................................................................RA Bolting DN50 PN3, DIN 11851 / 316L .................................................................................................RB Bolting DN80 PN3, DIN 11851 / 316L .................................................................................................XC Mounting strap 170mm / 1.4404 .........................................................................................................XD Mounting strap 300 mm / 1.4404 ........................................................................................................YD Combi compr.flange DN80PN16, ANSI3", 150 lb / PPH .....................................................................AE Adapter flange DN100PN16 FKM(Viton) / PPH ..................................................................................AH Adapter flange DN150PN16 FKM(Viton) / PPH ..................................................................................FK Adapter flange ANSI 4"150psi FKM(Viton) / PPH ...............................................................................FM Adapter flange ANSI 6"150psi FKM(Viton) / PPH ...............................................................................UC Adapter flange JIS DN100 10K FKM(Viton) / PPH .............................................................................UE Adapter flange JIS DN150 10K FKM(Viton) / PPH .............................................................................
ElectronicsH Two-wire 4...20mA/HART® ...........................................................................................................B Four-wire 4...20mA/HART®; 90...253V AC; 50/60Hz ...................................................................P Profibus PA ...................................................................................................................................F Foundation Fieldbus ......................................................................................................................
Housing / ProtectionK Plastic / IP66/IP67 ..................................................................................................................A Aluminium / IP66/IP68 (0.2bar) ..............................................................................................D Aluminium double chamber / IP66/IP68 (0.2bar) ...................................................................8 StSt (electropolished) 316L / IP66/IP68 (0.2bar) ...................................................................
W StSt double chamber / IP66/IP68 (0.2 bar) ............................................................................R Plastic double chamber / IP66/IP67 .......................................................................................
Cable entry / Cable gland / Plug connectionM M20x1.5 / with / without ...................................................................................................N ½NPT / without / without .................................................................................................
Ind./adj.module (PLICSCOM) / Radio module PLICSMOBILEX without / without ........................................................................................................G without / mounted .....................................................................................................A mounted / without .....................................................................................................D mounted / mounted ...................................................................................................
Additional equipmentX without ................................................................................................................
PS61.
22
1
2
3
G1½ A
33 m
m(1
.3")
ø 40 mm(1.58")
100
mm
(3.9
4")22
mm
(0.8
7")
142
mm
(5.5
9")
SW 46 mm(1.81")
59,5
mm
(2.3
4")
Radar – VEGAPULS 62
1 Threaded version2 Threaded version with
temperature adapter up to +250 °C3 Flange version
You will find further process fittings and options under www.vega.com/configuratorYou will find further drawings and tables under www.vega.com/downloadsYou will find mounting accessory and welded sockets in chapter "Accessory"
Antenna-ø Length Beamangle
40 mm 100 mm 20°
48 mm 120 mm 15°
75 mm 216 mm 10°
95 mm 430 mm 8°
245 mm (parabolic) 138 mm 3°
VEGAPULS 62
Radar sensor for continuous level measurement
Application areaVEGAPULS 62 is suitable for applications in liquids in storage tanks or process vessels under arduous process conditions. Application possiblities are in the chemical industry, environment and recycling as well as in the petrochemical industry.
AdvantagesNon-contact measurement Simple mountingWear and maintenance-freeUnaffected by pressure, temperature, gas and vapourHigh measuring accuracySIL qualified
FunctionExtremely short microwave pulses are emitted via the antenna system to the measured product, reflected by the product surface and received again by the antenna system. The time from emission to reception of the signals is proportional to the level. A special evaluation procedure ensures a reliable and precise measurement.
23Radar – VEGAPULS 62
basic price:
ApprovalXX without ................................................................................................................................................................XM Ship approval .....................................................................................................................................................CX ATEX II 1G, 1/2G, 2G Ex ia IIC T6 ....................................................................................................................CA ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + WHG .......................................................................................................CM ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + Ship approval ..........................................................................................CI IEC Ex ia IIC T6 .................................................................................................................................................
DX ATEX II 1/2G, 2G Ex d ia IIC T5/T6 ...................................................................................................................DI IEC Ex d ia IIC T6 ..............................................................................................................................................
Version / MaterialB with horn antenna ø40 mm / 316L ...............................................................................................................C with horn antenna ø48 mm / 316L ...............................................................................................................D with horn antenna ø75 mm / 316L ...............................................................................................................E with horn antenna ø95 mm / 316L ...............................................................................................................K with parabolic antenna ø245mm / 316L ......................................................................................................F with ½"-standpipe / 316L .............................................................................................................................
Process fitting / MaterialGA Thread G¾A (DIN 3852-A) PN40 / 316L ...........................................................................................NA Thread ¾NPT (ASME B1.20.1) PN40 / 316L ....................................................................................GD Thread G1½A (DIN 3852-A) PN40 / 316L .........................................................................................ND Thread 1½NPT (ASME B1.20.1) PN40 / 316L ..................................................................................GB Thread G1½A (DIN 3852-A) PN100 / 316L .......................................................................................NB Thread 1½NPT (ASME B1.20.1) PN100 / 316L ................................................................................FC Flange DN50PN40 Form C, DIN2501 / 316L ....................................................................................FD Flange DN80PN40 Form C, DIN2501 / 316L ....................................................................................FE Flange DN100PN16 Form C, DIN2501 / 316L ..................................................................................FK Flange DN150PN16 Form C, DIN2501 / 316L ..................................................................................AE Flange 2" 150lb RF, ANSI B16.5 / 316L ............................................................................................AI Flange 3" 150lb RF, ANSI B16.5 / 316L ............................................................................................
AK Flange 4" 150lb RF, ANSI B16.5 / 316L ............................................................................................AM Flange 6" 150lb RF, ANSI B16.5 / 316L ............................................................................................
Seal / Process temperature2 FKM (Viton) and PTFE / -40...130°C ...........................................................................................3 FFKM (Kalrez 6375) and PTFE / -20...130°C ..............................................................................F FFKM (Kalrez 6375) and PEEK / -20...250°C .............................................................................H Graphite and ceramic / -200...450°C ...........................................................................................
ElectronicsH Two-wire 4...20mA/HART® ...................................................................................................B Four-wire 4...20mA/HART®; 90...253V AC; 50/60Hz ............................................................P Profibus PA ............................................................................................................................F Foundation Fieldbus ..............................................................................................................
Housing / ProtectionK Plastic / IP 66/IP 67 ........................................................................................................A Aluminium / IP66/IP68 (0.2 bar) .....................................................................................D Aluminium double chamber / IP66/IP68 (0.2 bar) ...........................................................8 StSt (electropolished) 316L / IP66/IP68 (0.2 bar) ...........................................................
W StSt double chamber / IP66/IP68 (0.2 bar) .....................................................................R Plastic double chamber / IP66/IP67 ...............................................................................
Cable entry / Cable gland / Plug connectionM M20x1.5 / with / without ...........................................................................................N ½NPT / without / without ..........................................................................................
Ind./adj.module PLICSCOM / Radio module PLICSMOBILEX without / without .................................................................................................G without / mounted ..............................................................................................A mounted / without ..............................................................................................D mounted / mounted ...........................................................................................
Additional equipmentX without .........................................................................................................
PS62.
Length standpipe / Total length316L (200-5850 mm) per 100 mm
24
2
31
99,5
mm
(3.9
2")
163
mm
(6.4
2")
ø 44 mm(1.73")
ø 75 mm(2.95")
ø 64 mm(2.52")
Radar – VEGAPULS 63
1 Flange version DN 502 Flange version DN 803 Tri-Clamp version 2"
You will find further process fittings and options under www.vega.com/configuratorYou will find further drawings and tables under www.vega.com/downloadsYou will find mounting accessory and welded sockets in chapter "Accessory"
VEGAPULS 63
Radar sensor for continuous level measurement of liquids
Application areaVEGAPULS 63 is suitable for measurement of very aggressive liquids or under special hygienic process conditions. Application possiblities are in the chemical as well as in the food processing and pharmaceutical industry.
Advantages Non-contact measurementFront-flush installationSimple mountingWear and maintenance-freeUnaffected by pressure, temperature, gas and vapourHigh measuring accuracySIL qualified
FunctionExtremely short microwave pulses are emitted via the antenna system to the measured product, reflected by the product surface and received again by the antenna system. The time from emission to reception of the signals is proportional to the level. A special evaluation procedure ensures a reliable and precise measurement.
25Radar – VEGAPULS 63
basic price:
ApprovalXX without .................................................................................................................................................................XM Ship approval ......................................................................................................................................................CX ATEX II 1G, 1/2G, 2G Ex ia IIC T6 ......................................................................................................................CA ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + WHG ........................................................................................................CM ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + Ship approval ...........................................................................................CI IEC Ex ia IIC T6 ...................................................................................................................................................
DX ATEX II 1/2G, 2G Ex d ia IIC T5/T6 ....................................................................................................................DI IEC Ex d ia IIC T6 ................................................................................................................................................
Version / Material / Process temperatureN with encapsulated horn antenna / TFM-PTFE / -40...200°C .........................................................................V hyg.encaps.horn ant. / TFM-PTFE+Viton / -25...130°C ................................................................................E hyg.encaps.horn ant. / TFM-PTFE+EPDM / -40...130°C ..............................................................................
Process fitting / MaterialCA Tri-Clamp 2" / 316L .............................................................................................................................CB Tri-Clamp 3" / 316L .............................................................................................................................CC Tri-Clamp 4" / 316L .............................................................................................................................RA Bolting DN50 PN16, DIN 11851 / 316L ...............................................................................................RB Bolting DN80 PN16, DIN 11851 / 316L ...............................................................................................LB Hyg.fitting w. tension flange DN32PN16 / 316L ..................................................................................LA Hyg.fitting w. compression nut F40 PN16 / 316L ................................................................................TB Tuchenhagen Varivent DN25... PN10 / 316L ......................................................................................QB Neumo Biocontrol sz. 50 PN16 / 316L ................................................................................................FC Flange DN50PN40 Form C, DIN2501 / 316L ......................................................................................FD Flange DN80PN40 Form C, DIN2501 / 316L ......................................................................................FE Flange DN100PN16 Form C, DIN2501 / 316L ....................................................................................FK Flange DN150PN16 Form C, DIN2501 / 316L ....................................................................................FM Flange DN150PN40 Form C, DIN2501 / 316L ....................................................................................AE Flange 2" 150lb RF, ANSI B16.5 / 316L .............................................................................................AI Flange 3" 150lb RF, ANSI B16.5 / 316L .............................................................................................
AK Flange 4" 150lb RF, ANSI B16.5 / 316L .............................................................................................AM Flange 6" 150lb RF, ANSI B16.5 / 316L .............................................................................................
ElectronicsH Two-wire 4...20mA/HART® ...........................................................................................................B Four-wire 4...20mA/HART®; 90...253V AC; 50/60Hz ...................................................................P Profibus PA ...................................................................................................................................F Foundation Fieldbus ......................................................................................................................
Housing / ProtectionK Plastic / IP 66/IP 67 ................................................................................................................A Aluminium / IP66/IP68 (0.2 bar) .............................................................................................D Aluminium double chamber / IP66/IP68 (0.2 bar) ..................................................................8 StSt (electropolished) 316L / IP66/IP68 (0.2 bar) ..................................................................
W StSt double chamber / IP66/IP68 (0.2 bar) ............................................................................R Plastic double chamber / IP66/IP67 .......................................................................................
Cable entry / Cable gland / Plug connectionM M20x1.5 / with / without ...................................................................................................N ½NPT / without / without .................................................................................................
Ind./adj.module (PLICSCOM) / Radio module PLICSMOBILEX without / without ........................................................................................................G without / mounted .....................................................................................................A mounted / without .....................................................................................................D mounted / mounted ...................................................................................................
Additional equipmentX without ................................................................................................................
PS63.
26
2
1
43 m
m(1
.69"
)35
2 m
m (1
3.86
")
22 m
m (0
.87"
)
94,5
mm
(3.7
2")
270
mm
(10.
63")
120
mm
(4.7
2")
545
mm
(21.
46")
395
mm
(15.
55")
82 m
m (3
.23"
)
2 m
m (0
.08"
)
ø 33 mm(1.3")
SW 50 mm(1.97")
ø 40 mm(1.58")ø 33 mm
(1.3")
G1½ A
Radar – VEGAPULS 65
1 Threaded version G1½ A2 Flange version DN 80
You will find further process fittings and options under www.vega.com/configuratorYou will find further drawings and tables under www.vega.com/downloadsYou will find mounting accessory and welded sockets in chapter "Accessory"
VEGAPULS 65
Radar sensor for continuous level measurement of liquids
Application areaVEGAPULS 65 is suitable for measurement of liquids in smaller vessels under ordinary process conditions. Application possibilities in virtually all areas of industry.
Advantages Non-contact measurement Simple mountingWear and maintenance-freeUnaffected by pressure, temperature, gas and vapourHigh measuring accuracySIL qualified
FunctionExtremely short microwave pulses are emitted via the antenna system to the measured product, reflected by the product surface and received again by the antenna system. The time from emission to reception of the signals is proportional to the level. A special evaluation procedure ensures a reliable and precise measurement.
27Radar – VEGAPULS 65
basic price:
ApprovalXX without ...............................................................................................................................................................XM Ship approval .....................................................................................................................................................CX ATEX II 1G, 1/2G, 2G Ex ia IIC T6 ....................................................................................................................CA ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + WHG .......................................................................................................CM ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + Ship approval ..........................................................................................CI IEC Ex ia IIC T6 .................................................................................................................................................
DX ATEX II 1/2G, 2G Ex d ia IIC T5/T6 ..................................................................................................................DI IEC Ex d ia IIC T6 ..............................................................................................................................................
Version / Material / Process temperatureK Rod antenna for sockets 50mm/PVDF a. PTFE/-40...130°C .....................................................................L Rod antenna for sockets 100mm / PTFE / -40...130/150°C .......................................................................M Rod antenna for sockets 250mm / PTFE / -40...130/150°C .......................................................................
Process fitting / MaterialGD Thread G1½A (DIN 3852-A) PN16 / 316L ........................................................................................GP Thread G1½A PN3 / PVDF ..............................................................................................................ND Thread 1½NPT (ASME B1.20.1) PN16 / 316L .................................................................................NP Thread 1½NPT PN3 / PVDF ............................................................................................................FC Flange DN50PN40 Form C, DIN2501 / 316L PTFE-plated ..............................................................FD Flange DN80PN40 Form C, DIN2501 / 316L PTFE-plated ..............................................................FE Flange DN100PN16 Form C, DIN2501/316L PTFE-plated .............................................................FK Flange DN150PN16 Form C, DIN2501 / 316L PTFE-plated ............................................................AE Flange 2" 150lb RF, ANSI B16.5 / 316L PTFE-plated ......................................................................AI Flange 3" 150lb RF, ANSI B16.5 / 316L PTFE-plated ......................................................................
AK Flange 4" 150lb RF, ANSI B16.5 / 316L PTFE-plated ......................................................................AM Flange 6" 150lb RF, ANSI B16.5 / 316L PTFE-plated ......................................................................
ElectronicsH Two-wire 4...20mA/HART® ........................................................................................................B Four-wire 4...20mA/HART®; 90...253V AC; 50/60Hz .................................................................P Profibus PA .................................................................................................................................F Foundation Fieldbus ...................................................................................................................
Housing / ProtectionK Plastic / IP 66/IP 67 .............................................................................................................A Aluminium / IP66/IP68 (0.2 bar) ..........................................................................................D Aluminium double chamber / IP66/IP68 (0.2 bar) ................................................................8 StSt (electropolished) 316L / IP66/IP68 (0.2 bar) ................................................................
W StSt double chamber / IP66/IP68 (0.2 bar) ..........................................................................R Plastic double chamber / IP66/IP67 ....................................................................................
Cable entry / Cable gland / Plug connectionM M20x1.5 / with / without ................................................................................................N ½NPT / without / without ...............................................................................................
Ind./adj.module (PLICSCOM) / Radio module PLICSMOBILEX without / without ......................................................................................................G without / mounted ...................................................................................................A mounted / without ...................................................................................................D mounted / mounted ................................................................................................
Additional equipmentX without ..............................................................................................................
PS65.
28
1 2
L
80 m
m(3
.45"
)20
5 m
m(8
.07"
)
ø 145 mm(5.71")
47 m
m(1
.85"
)
ø 8 mm(0.32")
ø 75 mm(2.95")
ø 52 mm(2.05")
Radar – VEGAPULS 66
1 Version with horn antenna ø 145 mm2 Version with standpipe antenna
You will find further process fittings and options under www.vega.com/configuratorYou will find further drawings and tables under www.vega.com/downloadsYou will find mounting accessory and welded sockets in chapter "Accessory"
Antenna-ø Length Beamangle
75 mm 68 mm 38°
96 mm 113 mm 30°
145 mm 205 mm 20°
195 mm 296 mm 17°
240 mm 380 mm 14°
VEGAPULS 66
Radar sensor for continuous level measurement of liquids
Application areaVEGAPULS 66 is suitable for measurement of liquids or under difficult and extreme process conditions. Application possiblities are in the chemical industry, environment and recycling as well as in the petrochemical industry.
Advantages Non-contact measurement with high pressures and temperaturesSimple mountingWear and maintenance-freeUnaffected by pressure, temperature, gas and vapourHigh measuring accuracySIL qualified
FunctionExtremely short microwave pulses are emitted via the antenna system to the measured product, reflected by the product surface and received again by the antenna system. The time from emission to reception of the signals is proportional to the level. A special evaluation procedure ensures a reliable and precise measurement.
29Radar – VEGAPULS 66
basic price:
ApprovalXX without ................................................................................................................................................................XM Ship approval .....................................................................................................................................................CX ATEX II 1G, 1/2G, 2G Ex ia IIC T6 .....................................................................................................................CA ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + WHG .......................................................................................................CM ATEX II 1G, 1/2G, 2G Ex ia IIC T6 + Ship approval ..........................................................................................CI IEC Ex ia IIC T6 .................................................................................................................................................
DX ATEX II 1/2G, 2G Ex d ia IIC T5/T6 ...................................................................................................................DI IEC Ex d ia IIC T6 ..............................................................................................................................................
Version / MaterialA without horn antenna for standpipe ..............................................................................................................D with horn antenna ø75 mm / 316L ...............................................................................................................E with horn antenna ø96 mm / 316L ...............................................................................................................H with horn antenna ø145 mm/316L ...............................................................................................................I with horn antenna ø195 mm / 316L .............................................................................................................J with horn antenna ø 240 mm / 316L ............................................................................................................F with standpipe ø50 mm / 316L .....................................................................................................................
Process fitting / MaterialFC Flange DN50PN40 Form C, DIN2501 / 316L .....................................................................................FD Flange DN80PN40 Form C, DIN2501 / 316L .....................................................................................FE Flange DN100PN16 Form C, DIN2501 / 316L ...................................................................................FK Flange DN150PN16 Form C, DIN2501 / 316L ...................................................................................FL Flange DN200PN16 Form C, DIN2501 / 316L ...................................................................................FI Flange DN250PN16 Form C, DIN2501 / 316L ...................................................................................
AE Flange 2" 150lb RF, ANSI B16.5 / 316L ............................................................................................AI Flange 3" 150lb RF, ANSI B16.5 / 316L ............................................................................................
AK Flange 4" 150lb RF, ANSI B16.5 / 316L ............................................................................................AM Flange 6" 150lb RF, ANSI B16.5 / 316L ............................................................................................AN Flange 8" 150lb RF, ANSI B16.5 / 316L ............................................................................................AP Flange 10" 150lb RF, ANSI B16.5 / 316L ..........................................................................................LP Flange 10" 150lb RJF, ANSI B16.5 / 316L .........................................................................................
Seal / Process temperature2 FKM (Viton) / -40...150°C ............................................................................................................3 FFKM (Kalrez 6375) / -20 ... 150 °C ............................................................................................G Graphite and ceramic / -60...250°C .............................................................................................H Graphite and ceramic /-60...400°C ..............................................................................................
ElectronicsH Two-wire 4...20mA/HART® ...................................................................................................B Four-wire 4...20mA/HART®; 90...253V AC; 50/60Hz ............................................................P Profibus PA ............................................................................................................................F Foundation Fieldbus ..............................................................................................................
Housing / ProtectionK Plastic / IP 66/IP 67 ........................................................................................................A Aluminium / IP66/IP68 (0.2 bar) .....................................................................................D Aluminium double chamber / IP66/IP68 (0.2 bar) ...........................................................8 StSt (electropolished) 316L / IP66/IP68 (0.2 bar) ...........................................................
W StSt double chamber / IP66/IP68 (0.2 bar) .....................................................................R Plastic double chamber / IP66/IP67 ...............................................................................
Cable entry / Cable gland / Plug connectionM M20x1.5 / with / without ...........................................................................................N ½NPT / without / without ..........................................................................................
Ind./adj.module PLICSCOM / Radio module PLICSMOBILEX without / without .................................................................................................G without / mounted ..............................................................................................A mounted / without ..............................................................................................D mounted / mounted ...........................................................................................
Additional equipmentX without .........................................................................................................
PS66.
Length standpipe / Total length316L (500-5950 mm) per 100 mm
30
2
1
15 m
m(0
.59"
)98
mm
(3.8
6")
170
mm
/ 30
0 m
m(6
.69"
) / (
11.8
1")
ø 75 mm(2.95")
ø 115 mm(4.53")
19 m
m(0
.75"
)
Radar – VEGAPULS 67
1 Mounting strap2 Adapter flange
You will find further process fittings and options under www.vega.com/configuratorYou will find further drawings and tables under www.vega.com/downloadsYou will find mounting accessory and welded sockets in chapter "Accessory"
VEGAPULS 67
Radar sensor for continuous level measurement of bulk solids
Application areaVEGAPULS 67 is suitable for level measurement of bulk solids. The application possibilities can be found in the food processing industry, the plastic processing and steel production as well as in the building industry.
Advantages Non-contact measurementSimple mountingWear and maintenance-freeUnaffected by pressure, temperature, gas and dustHigh measuring accuracySIL qualified
FunctionExtremely short microwave pulses are emitted via the antenna system to the measured product, reflected by the product surface and received again by the antenna system. The time from emission to reception of the signals is proportional to the level. A special evaluation procedure ensures a reliable and precise measurement.
31Radar – VEGAPULS 67
basic price:
ApprovalXX without ...................................................................................................................................................................GX II 1D, 1/2D, 2D Ex t IIIC T... Da, Da/Db, Db ..........................................................................................................GI Ex t IIIC T... Da, Da/Db, Db ...................................................................................................................................
Version / Material / Process temperatureB with plastic horn antenna ø80mm / PP / -40...80°C ........................................................................................
Process fitting / MaterialXX without compression flange ....................................................................................................................XC Mounting strap 170mm / 1.4404 .............................................................................................................XD Mounting strap 300mm / 1.4404 .............................................................................................................YD Combi compr. flange DN80PN16, ANSI3", 150 lb / PPH .......................................................................AE Adapter flange DN100PN16 FKM(Viton) / PPH .....................................................................................AH Adapter flange DN150PN16 FKM(Viton) / PPH .....................................................................................FK Adapter flange ANSI 4"150lb FKM(Viton) / PPH ....................................................................................FM Adapter flange ANSI 6"150lb FKM(Viton) / PPH ....................................................................................UC Adapter flange JIS DN100 10K FKM(Viton) / PPH ................................................................................UE Adapter flange JIS DN150 10K FKM(Viton) / PPH ................................................................................
ElectronicsH Two-wire 4...20mA/HART® .............................................................................................................V Four-wire 4...20mA/HART® .............................................................................................................P Profibus PA ......................................................................................................................................F Foundation Fieldbus ........................................................................................................................
Housing / ProtectionK Plastic / IP 66/IP 67 ...................................................................................................................A Aluminium / IP66/IP68 (0.2 bar) ................................................................................................D Aluminium double chamber / IP66/IP68 (0.2 bar) ......................................................................V StSt (precision casting) 316L / IP66/IP68 (0.2 bar) ...................................................................
Cable entry / Cable gland / Plug connectionM M20x1.5 / with / without ......................................................................................................N ½NPT / without / without ....................................................................................................
Ind./adj.module (PLICSCOM) / Radio module PLICSMOBILEX without / without ...........................................................................................................A mounted / without .........................................................................................................
Additional equipmentX without ....................................................................................................................
PS67.
32
1 2 3
G1½ A
37,5
mm
(1.4
8")
236
mm
(9.2
9")
ø 40 mm(1.58")ø 75 mm
(2.95")
100
mm
(3.9
4")
41 m
m (1
.61"
)
22 m
m(0
.87"
)22 m
m(0
.87"
)
11,5
mm
(0.4
5")
142
mm
(5.5
9")
216
mm
(8.5
")
SW 46 mm(1.81")
1 Threaded version with horn antenna 2 Threaded version with horn antenna
and temperature adapter3 Version with horn antenna and swivelling
holder
You will find further process fittings and options under www.vega.com/configuratorYou will find further drawings and tables under www.vega.com/downloadsYou will find mounting accessory and welded sockets in chapter "Accessory"
Radar – VEGAPULS SR 68
VEGAPULS SR 68
Radar sensor for continuous level measurement of bulk solids
Application areaThe VEGAPULS SR 68 is designed for level measurement of bulk solids even under arduous process conditions. The mechanical construction as well as the electronics are optimised for this application. The application possibilities are in the food processing industry, the plastic processing and the steel generation as well as in the construction industry.
AdvantagesNon-contact measurementSimple mountingWear and maintenance-freeHigh measuring accuracyMeasuring range up to 30 m
FunctionExtremely short microwave pulses are emitted via the antenna system to the measured product, reflected by the product surface and received again by the antenna system. The time from emission to reception of the signals is proportional to the level. A special evaluation procedure ensures the reliable and precise measurement.
33Radar – VEGAPULS SR 68
basic price:
ApprovalXX without ............................................................................................................................................................CX ATEX II 1G, 1/2G, 2G Ex ia IIC T5 .................................................................................................................CK II 1, 1/2, 2G Ex ia IIC T6 + II 1, 1/2, 2D Ex t IIIC T. ........................................................................................DX ATEX II 1/2G, 2G Ex d ia IIC T5/T6 ...............................................................................................................GX II 1D, 1/2D, 2D Ex t IIIC T... Da, Da/Db, Db ...................................................................................................TX ATEX I M2 EEx ia I .........................................................................................................................................
Version / MaterialB with horn antenna ø40 mm / 316L ...........................................................................................................C with horn antenna ø48 mm / 316L ...........................................................................................................D with horn antenna ø75 mm / 316L ...........................................................................................................E with horn antenna ø95 mm / 316L ...........................................................................................................
Process fitting / MaterialGD Thread G1½A (DIN 3852-A) PN40 / 316L ......................................................................................ND Thread 1½NPT (ASME B1.20.1) PN40 / 316L ...............................................................................GB Thread G1½A (DIN 3852-A) PN100 / 316L ....................................................................................NB Thread 1½NPT (ASME B1.20.1) PN100 / 316L .............................................................................1F Swivelling holder for flange 2" 150lb / 316L ....................................................................................1G Swivelling holder for flange 3" 150lb / 316L ....................................................................................1H Swivelling holder for flange 4" 150lb / 316L ....................................................................................1O Swivelling holder for flange DN50 / 316L ........................................................................................1P Swivelling holder for flange DN80 / 316L ........................................................................................1Q Swivelling holder with flange DN100 PN16 / 316L ..........................................................................FC Flange DN50PN40 Form C, DIN2501 / 316L ..................................................................................FD Flange DN80PN40 Form C, DIN2501 / 316L ..................................................................................FE Flange DN100PN16 Form C, DIN2501 / 316L ................................................................................AE Flange 2" 150lb RF, ANSI B16.5 / 316L ..........................................................................................AI Flange 3" 150lb RF, ANSI B16.5 / 316L ..........................................................................................
AK Flange 4" 150lb RF, ANSI B16.5 / 316L ..........................................................................................Seal / Process temperature2 FKM (Viton) and PTFE / -40...130°C .........................................................................................3 FFKM (Kalrez 6375) and PTFE / -20...130°C ............................................................................F FFKM (Kalrez 6375) and PEEK / -20...250°C ...........................................................................
ElectronicsH Two-wire 4...20mA/HART® .................................................................................................B Four-wire 4...20mA/HART®; 90...253V AC; 50/60Hz ..........................................................P Profibus PA ..........................................................................................................................F Foundation Fieldbus ............................................................................................................
Housing / ProtectionK Plastic / IP 66/IP 67 ......................................................................................................A Aluminium / IP66/IP68 (0.2 bar) ...................................................................................D Aluminium double chamber / IP66/IP68 (0.2 bar) .........................................................8 StSt (electropolished) 316L / IP66/IP68 (0.2 bar) .........................................................
W StSt double chamber / IP66/IP68 (0.2 bar) ..................................................................R Plastic double chamber / IP66/IP67 .............................................................................
Cable entry / Cable gland / Plug connectionM M20x1.5 / with / without .........................................................................................N ½NPT / without / without .......................................................................................
Indic./adj.module PLICSCOM / Radio module PLICSMOBILEX without / without ..............................................................................................G without / mounted ............................................................................................A mounted / without ............................................................................................D mounted / mounted .........................................................................................
Additional equipmentX without ......................................................................................................K Rinsing connection ...................................................................................V Rinsing connection with reflux valve .........................................................
PSSR68.
34
1 2
3
G1½ A
37,5
mm
(1.4
8")
131
mm
(5.1
6")
ø 40 mm(1.58")ø 75 mm
(2.95")
ø 244 mm (9.61")
100
mm
(3.9
4")
41 m
m (1
.61"
)
22 m
m(0
.87"
)22 m
m(0
.87"
)
11,5
mm
(0.4
5")
142
mm
(5.5
9")
216
mm
(8.5
")
SW 46 mm(1.81")
Radar – VEGAPULS 68
1 Threaded version with horn antenna 2 Threaded version with horn antenna
and temperature adapter3 Version with parabolic antenna
You will find further process fittings and options under www.vega.com/configuratorYou will find further drawings and tables under www.vega.com/downloadsYou will find mounting accessory and welded sockets in chapter "Accessory"
Antenna-ø Length Beamangle
40 mm 100 mm 20°
48 mm 120 mm 15°
75 mm 216 mm 10°
95 mm 430 mm 8°
245 mm (parabolic) 138 mm 3°
VEGAPULS 68
Radar sensor for continuous level measurement of bulk solids
Application areaVEGAPULS 68 is suitable for level measurement of bulk solids also under difficult process conditions. The mechanical construction as well as the electronics are optimised for this application. The application possibilities can be found in the food processing industry, the plastic processing and steel production as well as in the building industry.
Advantages Non-contact measurementSimple mountingWear and maintenance-freeUnaffected by pressure, temperature, gas and dustHigh measuring accuracySIL qualified
FunctionExtremely short microwave pulses are emitted via the antenna system to the measured product, reflected by the product surface and received again by the antenna system. The time from emission to reception of the signals is proportional to the level. A special evaluation procedure ensures a reliable and precise measurement.
35Radar – VEGAPULS 68
basic price:
ApprovalXX without .................................................................................................................................................................XM Ship approval .......................................................................................................................................................CX ATEX II 1G, 1/2G, 2G Ex ia IIC T5 ......................................................................................................................CM ATEX II 1G, 1/2G, 2G Ex ia IIC T5 + ship approval ............................................................................................CK II 1, 1/2, 2G Ex ia IIC T6 + II 1, 1/2, 2D Ex t IIIC T. .............................................................................................CI IEC Ex ia IIC T5 ...................................................................................................................................................
DX ATEX II 1/2G, 2G Ex d ia IIC T5/T6 .....................................................................................................................DI IEC Ex d ia IIC T6 ................................................................................................................................................
GX II 1D, 1/2D, 2D Ex t IIIC T... Da, Da/Db, Db ........................................................................................................TX ATEX I M2 EEx ia I ..............................................................................................................................................
Version / MaterialB with horn antenna ø40 mm / 316L .................................................................................................................C with horn antenna ø48 mm / 316L .................................................................................................................D with horn antenna ø75 mm / 316L .................................................................................................................E with horn antenna ø95 mm / 316L .................................................................................................................K with parabolic antenna ø245 mm / 316L .......................................................................................................
Process fitting / MaterialGD Thread G1½A (DIN 3852-A) PN40 / 316L ...........................................................................................ND Thread 1½NPT (ASME B1.20.1) PN40 / 316L .....................................................................................GB Thread G1½A (DIN 3852-A) PN100 / 316L .........................................................................................NB Thread 1½NPT (ASME B1.20.1) PN100 / 316L ...................................................................................1F Swivelling holder for flange 2" 150lb / 316L .........................................................................................1G Swivelling holder for flange 3" 150lb / 316L .........................................................................................1H Swivelling holder for flange 4" 150lb / 316L .........................................................................................1O Swivelling holder for flange DN50 / 316L .............................................................................................1P Swivelling holder for flange DN80 / 316L .............................................................................................1Q Swivelling holder with flange DN100 PN16 / 316L ...............................................................................FC Flange DN50PN40 Form C, DIN2501 / 316L .......................................................................................FD Flange DN80PN40 Form C, DIN2501 / 316L .......................................................................................FE Flange DN100PN16 Form C, DIN2501 / 316L .....................................................................................AE Flange 2" 150lb RF, ANSI B16.5 / 316L ...............................................................................................AI Flange 3" 150lb RF, ANSI B16.5 / 316L ...............................................................................................
AK Flange 4" 150lb RF, ANSI B16.5 / 316L ...............................................................................................Seal / Process temperature2 FKM (Viton) and PTFE / -40...130°C ..............................................................................................3 FFKM (Kalrez 6375) and PTFE / -20...130°C .................................................................................F FFKM (Kalrez 6375) and PEEK / -20...250°C ................................................................................H Graphite and ceramic / -200...450°C ..............................................................................................
ElectronicsH Two-wire 4...20mA/HART® ......................................................................................................B Four-wire 4...20mA/HART®; 90...253V AC; 50/60Hz ..............................................................P Profibus PA ..............................................................................................................................F Foundation Fieldbus .................................................................................................................
Housing / ProtectionK Plastic / IP 66/IP 67 ...........................................................................................................A Aluminium / IP66/IP68 (0.2 bar) ........................................................................................D Aluminium double chamber / IP66/IP68 (0.2 bar) .............................................................8 StSt (electropolished) 316L / IP66/IP68 (0.2 bar) ..............................................................
W StSt double chamber / IP66/IP68 (0.2 bar) .......................................................................R Plastic double chamber / IP66/IP67 ..................................................................................
Cable entry / Cable gland / Plug connectionM M20x1.5 / with / without ..............................................................................................N ½NPT / without / without ............................................................................................
Ind./adj.module PLICSCOM / Radio module PLICSMOBILEX without / without ...................................................................................................G without / mounted .................................................................................................A mounted / without .................................................................................................D mounted / mounted ..............................................................................................
Additional equipmentX without ...........................................................................................................K Rinsing connection ........................................................................................V Rinsing connection with reflux valve ..............................................................
PS68.
36 Radar – VEGAPULS