r22t6 r22t8 1.0 q - GIGABYTE

Service Guide

GIGABYTEGS-R22T61-RH/GS-R22T81-RH

2U Rack Mount Server

Dual Intel® Xeon LGA1366 Processor Serverboard

Rev. 1.0

PrefaceBefore using this information and the product it supports, please read the following general information.

1. This Service Guide provides you with all technical information relating to the BASIC

CONFIGURATION decided for GIGABYTE's “global” product offering. To better fit local market

requirements and enhance product competitiveness, your regional office MAY have decided to

extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).

These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such

cases, please contact your regional offices or the responsible personnel/channel to

provide you with further technical details.

2. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information

available on your regional web or channel. For whatever reason, if a part number change is made,

it will not be noted in the printed Service Guide. For GIGABYTE-AUTHORIZED SERVICE

PROVIDERS, your GIGABYTE office may have a DIFFERENT part number code to those

given in the FRU list of this printed Service Guide. You MUST use the list provided by your

regional GIGABYTE office to order FRU parts for repair and service of customer machines.

3

GS-R22T61-RH/GS-R22T81-RH Rack Mount Server

Table of Contents

Preface .................................................................................................... 2

Safety, Care and Regulatory Information ................................................ 5

System Specification .............................................................................. 9

System Hardware Installation ................................................................ 11Chassis Removal and Installation ................................................................................. 12

CPU Installation ............................................................................................................... 13

Heat Sink Installation ....................................................................................................... 14

Memory Installation ......................................................................................................... 15

PCI Expansion Card Installation (GC-RLE2N-RH/GC-RFE2N-RH) .......................... 18

PCI Expansion Card Installation (GC-RFX2N-RH/Optional) ....................................... 20

GS-R22T81-RH Hard Disk Drive Installation ................................................................ 22

GS-R22T61-RH Hard Disk Drive Installation ................................................................ 23

FAN Duct Removal and Installation .............................................................................. 24

Appearance of GS-R22T61-RH/GS-R22T81-RH ................................... 25Front View of GS-R22T61-RH (For 3.5 HDDs solution) .............................................. 25

Front View of GS-R22T81-RH (For 2.5 HDDs solution) .............................................. 25

Rear View of GS-R22T61-RH/GS-R22T81-RH ........................................................... 26

Front Panel LED Indicators ............................................................................................. 27

LAN port LED Indicator .................................................................................................... 28

Hard Disk Drive LED Description ................................................................................... 29

GC-BS28E-RH Back plane board Components Description ....................................... 30

(for 2.5”HDD) .................................................................................................................... 30

GC-BS26E-RH Back plane board Components Description ....................................... 32

(for 3.5”HDD) .................................................................................................................... 32

System Block Diagram ................................................................................................... 34

GS-R22T61-RH Cable Routing ...................................................................................... 35

.......................................................................................................................................... 35

GS-R22T81-RH Cable Routing ...................................................................................... 36

Connector Icon Description ............................................................................................. 37

Motherboard Placement and Jumper Setting ...................................... 38GA-7TTSH-RH Motherboard Component ...................................................................... 38

Motherboard Jumper Setting ........................................................................................... 41

Expansion Card Components Description .................................................................... 43

4

Table of Content

BIOS Setup ........................................................................................... 46Main ........................................................................................................... 48

Advanced ................................................................................................... 50Processor Configuration .................................................................................................. 51

Processor Power Management ..................................................................................... 55

Memory Configuration ..................................................................................................... 58

Advanced Chipset Configuration ................................................................................... 60

PCI Configuration ............................................................................................................. 64

SATA Configuration .......................................................................................................... 66

I/O DeviceConfiguration .................................................................................................. 69

Boot Configuration ............................................................................................................ 71

Thermal and Acoustic Configuration .............................................................................. 73

Power ......................................................................................................... 75

Security ...................................................................................................... 77

Server ......................................................................................................... 79System Management ...................................................................................................... 80

Console Redirection ........................................................................................................ 82

Event Log Configuration .................................................................................................. 84

Boot ............................................................................................................ 85

Exit ............................................................................................................. 86

Appexdix A Phoenix BIOS Beep Codes ............................................. 92

Appexdix B PhoenixBIOS POST Error Messages List ...................... 96

5


Safety, Care and Regulatory Information Important safety information

Read and follow all instructions marked on the product and in the documentation before you operate

your system. Retain all safety and operating instructions for future use.

* The product should be operated only from the type of power source indicated on the rating label.

* If your computer has a voltage selector switch, make sure that the switch is in the proper position for

your area. The voltage selector switch is set at the factory to the correct voltage.

* The plug-socket combination must be accessible at all times because it serves as the main disconnect-

ing device.

* All product shipped with a three-wire electrical grounding-type plug only fits into a grounding-type power

outlet. This is a safety feature. The equipment grounding should be in accordance with local and national

electrical codes. The equipment operates safely when it is used in accordance with its marked electrical

ratings and product usage instructions

* Do not use this product near water or a heat source.

* Set up the product on a stable work surface or so as to ensure stability of the system.

* Openings in the case are provided for ventilation. Do not block or cover these openings. Make sure you

provide adequate space around the system for ventilation when you set up your work area. Never insert

objects of any kind into the ventilation openings.

* To avoid electrical shock, always unplug all power cables and modem cables from the wall outlets

before removing covers.

* Allow the product to cool before removing covers or touching internal components.

Precaution for Product with Laser DevicesObserve the following precautions for laser devices:

* Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other

than those specified in the product's documentation.

* Only authorized service technicians should repair laser devices.

Precaution for Product with Modems, Telecommunications, ot Local Area

Network OptionsObserve the following guidelines when working with options:

* Do not connect or use a modem or telephone during a lightning storm. There may be a risk of electrical

shock from lightning.

6

Safety Information* To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.

* Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle.

* Disconnect the modem cable before opening a product enclosure, touching or installing internal

components, or touching an uninsulated modem cable or jack.

* Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.

Federal Communications Commission (FCC) StatementWarning

This is a class A product. In a domestic environment this product may cause radio

interference

In which case the user may be required to take adequate measures.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission

limits. Neither the provider nor the manufacturer are responsible for any radio or television interference

caused by using other than recommended cables and connectors or by unauthorized changes or

modifications to this equipment. Unauthorized changes or modifications could void the user's authority to

operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

FCC part 68 (applicable to products fitted with USA modems)The modem complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among

other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment.

You must, upon request, provide this information to your telephone company.

If your telephone equipment causes harm to the telephone network, the Telephone Company may

discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is not

practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with

7


the FCC.

Your telephone company may make changes in its facilities, equipment, operations, or procedures that

could affect proper operation of your equipment. If they do, you will be notified in advance to give you an

opportunity to maintain uninterrupted telephone service.

The FCC prohibits this equipment to be connected to party lines or coin-telephone service.

The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part

68, Sec. 68.381 (c) (3)).

/ for Canadian users only /

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital

apparatus as set out in the radio interference regulations of Industry Canada.

Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux

appareils numeriques de Classe A prescrites dans le reglement sur le brouillage radioelectrique edicte par

Industrie Canada.

DOC notice (for products fitted with an Industry Canada-compliant modem)

The Canadian Department of Communications label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective, operational and safety

requirements. The Department does not guarantee the equipment will operate to the user satisfaction.

Before installing this equipment, users ensure that it is permissible to be connected to the facilities of the

local Telecommunications Company. The equipment must also be installed using an acceptable method

of connection. The customer should be aware that compliance with the above conditions might not prevent

degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated

by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions,

may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility,

telephone lines and internal metallic water pipe system, if resent are connected together. This precaution

may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate.

8

Safety Information

NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total

load to be connected to a telephone loop which is used by the device, to prevent overloading. The

termination on a loop may consist of any combination of devices subject only to the requirement that the

sum of the Load Numbers of all the devices does not exceed 100.

/ for European users only /

Class A equipmentThis device has been tested and found to comply with the limits for a class A digital device pursuant

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generate, uses, and can radiate radio frequency energy, and if not installed and used in accordance

with the instructions, may cause harmful interference to radio communication. Operation of this

equipment in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at personal expence.

However, there is no guarantee that interference will not occur in a particular installation. If this

device does cause harmful interference to radio or television reception, which can be determined by

tuning the device off and on, the user is encouraged to try to correct the interference by on or more of

the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the device and receiver

Connect the device into an outlet on a circuit different from that to which the receiver is

connected

Consult the dealer or an experienced radio/television technician for help

CAUTION Danger of explosion if battery is incorrectly

replaced.

Replace only with the same or equivalent

type recommended by the manufacturer.

Dispose of used batteries according to the

manufacturer’s instructions.

9


Motherboard GA-7TTSH1-RH

Processor Supported Supports dual Intel® Xeon® processors

Intel Xeon® Dual-Core/Quad-Core processor in LGA 1366 socket

Supports Intel Quickpath Interconnect up to 6.4 GT/s

Chipset Northbridge: Intel® 5520 Chipset

Southbridge: Intel® ICH10R

System Memory:

Memory Capacity 12 x DDR 3 sockets up to 48GB/96GB (1 to 4 GB unbuffered

DIMMs for up to 48GB or 1 to 8 GB registered DIMM for up to

96GB of total system memory)

Memory Type DDR 3 133 MHz ECC registered/unbuffered DIMMs

DIMM Size 512MB, 1GB, 2GB, 4GB, and 8GB capability modules support

Error Correction: Single-bit Errors Correction, Multiple Bit Errors Detection

Riser Slot

Full height riser card: (Top) One PCI-E x8 slot (PCI-E x 8 throughput) , Gen2.

(Black color connector)

(Middle)One PCI-E x8 slot (PCI-E x 8 throughput) , Gen2.


(Bottom). (Black color connector) PCI-E x8 (PCI-E x8 throughput),

Gen2.

Full height riser card: (Optional) (Top) One PCI-X 64/133MHz (White color connector)

(Middle)One PCI-E x8 slot (PCI-E x 8 throughput) , Gen2.


(Bottom)One PCI-E x8 slot (PCI-E x 8 throughput) , Gen2.


Low-profile riser card: (Top)One PCI-E x8 slot (PCI-E x 8 throughput), Gen2.


(Middle)One PCI-E x8 slot (PCI-E x4 throughput), Gen1.

(White color connector)

SATA RAID controller Intel® ICH10R

Supports LSI Software RAID 0/1/10

Cooling Fans: 6 X System Fan

System Specification

1 0

Feature SummaryIntegrated LANs:

Controller Intel® 82576EB controller support dual GbE ports

Integrated Graphics:

Controller Integrated in Server Engines Pilot II

Graphics Memory 32MB DDR2

Mass Storage System 6 x 3.5” Hot-Swap SATA /SAS HDDs

Or, 16 x 2.5” Hot-Swap SATA /SAS HDDs

1 x DVD Combo

Super I/O

Controller ITE IT8720 Super I/O

Front I/O 1 x VGA port

2 x USB 2.0 dual-port connector

Rear I/O P/S 2 Keyboard and Mouse Connectors

1 x Serial port

4 x USB 2.0 ports

1 x VGA connector

2 x GLAN ports

1 x 10/100 LAN port

System BIOS:

BIOS Type Phoenix BIOS on 8Mb flash ROM

Server Management Functions: (Optional device)

BMC Chip Server Engines POLIT 2 IPMI 2.0 controller

Failure Detection IPMI 2.0 specification of Server management

Event Logging 32KB Nonvolatile Memory to Log System Failure Events

Remote Management Follow the IPMI 2.0 specification of Server management

Environment

Ambient Temperature Operating Temperature: 5oC to 35oC

Non-operating Temperature: 0oC to 50oC

Relative Humidity 10-80% operating Humidity at 30o C

System Dimention: 432mm x 210mm x 650mm

Electrical Power Supply Redundant Power Supply 750W

1 1


Pre-installation Instructions

Perform the steps below before you open the server or before you remove or replace

any component.

1. Back up all important system and data files before performing any hardware

configuration.

2. Turn off the system and all the peripherals connected to it.

3. Unplug all cables from the power outlets.

4. Disconnect all telecommunication cables from their ports.

5. Place the system unit on a flat and stable surface.

6. Open the system according to the instructions.

Warning! Failure to properly turn off the server before you start installing components

may cause serious

damage. Do not attempt the procedures described in the following sections unless you

are a qualified service

technician.

System Hardware Installation

1 2

Hardware Installation Process

Chassis Removal and InstallationStep 1 Remove the screw on the chassis.

Step 2 Slide toward the top chassis cover.

Step 3 Lift up to remove the top chassis cover.

Step 4 Reverse Step 1, ,2, 3 to replace the chassis cover

1

3

2

1 3


1

23

CPU InstallationPlease make sure the CPU type and speed that are supported by the motherboard.

Step 1 Raise the metal locking lever on the socket. Insert the CPU with the correct orientation.

Step 2 The CPU only fits in one orientation.

Step 3 Push the metal lever back into locked position.

1 4


Heat Sink InstallationStep 1 Place the Heat Sink on the CPU. Before putting the heat sink on the CPU, please well

remember to apply the thermal conductivity compound on the CPU.

Step 2 Seat the heat sink in the retention modules with the four screws. Installation completed.

1

1

1

1

1

2

2

2

2

2

2

2

1 5


Memory Installation

1

2

2

CPU1

CPU2

DIMMA2DIMMA1

DIMMB2DIMMB1

DIMMC2DIMMC1

DIMMD2DIMMD1

DIMME2DIMME1 DIMMF2

DIMMF1

Step 1. Insert the DIMM memory module vertically into the DIMM slot, and push it down.

Step 2. Close the plastic clip at both edges of the DIMM slots to lock the DIMM module.

NOTE! DIMM must be populated in order starting from DIMMA1/D1 sockets. For dualquad

channel operation, DIMMs must be installed in matched pairs.

Step 3. Reverse the installation steps when you wish to remove the DIMM module.

1 6


U-DIMM Population Table

DIMMA1/D1

1GB

Interleavemode

SingleChannel

DualChannel

ThreeChannel

DIMMA2/D2 DIMMB1/E1 DIMMB2/E2 DIMMC1/F1 DIMMC2/F2

Channel A Channel B Channel CTotal Memory

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

2GB

4GB

8GB

8GB

4GB1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

6GB

12GB

16GB

6GB

3GB

16GB

24GB

1 7


R-DIMM Population Table

Interleavemode

SingleChannel

DualChannel

ThreeChannel

Channel A Channel B Channel CTotal Memory

DIMMA1/D1

1GB

DIMMA2/D2 DIMMB1/E1 DIMMB2/E2 DIMMC1/F1 DIMMC2/F2

2GB

4GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB 1GB

2GB

4GB

8GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

6GB

12GB

24GB

48GB

8GB

2GB

4GB

8GB

16GB

4GB

8GB

16GB

32GB

3GB

6GB

12GB

24GB

1 8


PCI Expansion Card Installation (GC-RLE2N-RH/GC-RFE2N-RH)Step 1 Loosen the riser bracket screws which attached on on the system.

Step 2 Loosen the rest riser bracket bracket screws.

Step 3 Lift the riser bracket slightly, then pull it out from the server chassis.

Step 4 Slide the expansion card into the slot until the card firmly seats.

Step 5 Slide another expansion card into the slot until the card firmly seats.

Align the riser bracket to the system module.

3

2

11

2

2

1 9


4

5

2 0


PCI Expansion Card Installation (GC-RFX2N-RH/Optional)Step 1 Loosen the riser bracket screws which attached on on the system.

Step 2 Loosen the rest riser bracket bracket screws.

Step 3 Lift the riser bracket slightly, then pull it out from the server chassis.

Step 4 Attach the PCI-E card to the riser bracket.

Step 5 Secure the card with screws.

Step 6 Attach anothr PCI-E card to the riser bracket the other side.

Step 7 Secure the card with screws.

Step 8 Align the riser bracket to the system module until it firmly seats.

3

2

11

2

2

2 1


4

5

5

6

7

77

2 2


GS-R22T81-RH Hard Disk Drive InstallationStep 1 Press the release button.

Step 2 Pull the blank out of the drive bay.

Step 3 Place hard disk into blank.

Step 4 Secure it with screws.

Slide the blank into the bay until it locks into place. Connect cable and power.

1

3

2

4

4

2 3


GS-R22T61-RH Hard Disk Drive InstallationStep 1 Press the release button.

Step 2 Pull the blank out of the drive bay.

Step 3 Place hard disk into blank.

Step 4 Secure it with screws.

Slide the blank into the bay until it locks into place. Connect cable and power.

3

2

4

4

1

2 4


FAN Duct Removal and InstallationStep 1 Lift the fan duct from the chassis.

Step 2 To install fan duct, align the fan duct with the guiding groove. Push down the fan duct into system

until its firmly seats.

1

2 5


210 3 4 5 6 7 8 9 1011 121314 15

Front View of GS-R22T61-RH (For 3.5 HDDs solution)Appearance of GS-R22T61-RH/GS-R22T81-RH

2

1

0 3

4

5

NOTE! For Front LED description, please go to Switch and LED Indicators

Introduction section.

Number indicates the HDD installation order.

Front View of GS-R22T81-RH (For 2.5 HDDs solution)

Front panel LEDs and Power Button

USB connectors

VGA port

3.5” Hot-Swap SATA/SAS HDDs

Front panel LEDs and Power Button

USB connectors

VGA port

2.5” Hot-Swap SATA/SAS HDDs

System Appearance

2 6

Rear View of GS-R22T61-RH/GS-R22T81-RH

Power

Keyboard connector

G-LAN ports

COM port

VGA port

10/100 LAN port

USB connectors

ID switch

Low-profile riser slots

Full-height riser slots

Mouse connector

2 7


Front Panel LED Indicators

No Indicator

1 LAN1

activity

2 LAN2

activity

3 HDD

activity

4 System

status

5 System ID

Color State Description

Green On Link between system and

network or no access

Green Blink Network access

Green On Link between system and

network or no access

Green Blink Network access

Green Blink HDD access

N/A Off No access

Green On Running or normal operation

Amber On Critical or non-recoverable

condition (Power module or

voltage power supply failure

or critical temperature)

Amber Blink Non-critical condition

N/A Off System not ready

May indicate the following:

POST error

NMI event

Processor or terminator

missing

Blue On System identification is active

Off System identification is disabled

2 8

LED Description

No Indicator

6 Power

status


Green On System has power supplyto it or

ACPI S0 state

Green Blink System is in ACPI S1 state

(sleep mode)

N/A Off System is not powered on or in

ACPI S5 state (power off)

System is in ACPI S4 state

(hlbernate mode)

LAN port LED Indicator

No Name

1 Speed

indicator

2 Link/activity

indicator


N/A Off 10Mbps connection

Green On 100Mbps connection

Yellow On 1000Mbps connection

Note: The server management port does

not support 1000Mbps connection

Green On Active connection

Green Blink Transmit or receive connection

2 9

LED Description

Hard Disk Drive LED Description

Description

HDD Prsent

HDD access

HDD failure

HDD removed

HDD connected and

rebuilding data

HDD locate

SAS/SATA HDD indicator

Green Red

On Off

Blink (4Hz) Off

Off On

Off On

On Blink (1 Hz)

Blink (4Hz) Blink (4Hz)

3 0


GC-BS28E-RH Back plane board Components Description

(for 2.5”HDD)

No Code Description

1 SAS/CON1 SAS 8484 32-pin connector (port 0 ~ 3)

2 SAS/CON2 SAS 8484 32-pin connector (port 4 ~ 7)

3 CN2/X1 Power connector (4-pin)

4 CN1/X1 Power connector (4-pin)

5 J3 SMBUS connector for backplane cascade

6 J1 SMBUS connector to RAID card

7 J2 SMBUS connector to main board (J2)

8 J27 Close 1-2: Two LED indication (default)

Close 2-3: Single LED indication (backward support)

9 J21 LED Power Select

10 SF6 System fan connector for system fan #6






16 SGPIO_JP2 SGPIO Connector

17 SGPIO_JP1 SGPIO Connector

1234

56

7

8

9

19

20

21

10 12 13

18

11 14 15

22

17

16

3 1

Back Plane Board Description

GC-BS28E-RH Back plane board Components Description Condt’

J28 J29 J30 J31

B/P_1 Close 2-3 Close 1-2 Close 2-3 Close 2-3

B/P_2 Close 1-2 Close 2-3 Close 1-2 Close 1-2

No Code Description

18 J28 Back plane board adress setting




22 J12 Debug port

1234

56

7

8

9

19

20

21

10 12 13

18

11 14 15

22

17

16

3 2


GC-BS26E-RH Back plane board Components Description

(for 3.5”HDD)

4

1

2 5

7

6

8

9

101112131415

16

18 17

20 19 21 22

2324

25

26

3

No Code Description

1 J1 SMBUS connector from RAID card

2 J2 SMBUS connector from Enclosure IC(Motherboard)

3 J3 SMBUS connector from RAID card

4 SGPIO_J1 SGPIO Connector

5 SGPIO_J2 SGPIO Connector

6 SAS/CON1 SAS 8484 32pin Connector

7 SAS/CON2 SAS 8484 32pin Connector

8 CN1/X1 1x4 Pin Power Connector

9 CN1/X2 1x4 Pin Power Connector

10 FAN1 System fan connector






16 J12 Debug Port

17 J13 LED Power charge selection

1-2 Close: No changes

18 J14 For dependent on HDD Tray’s LED conduct to setting

Close 1-2: Two LED

Close 2-3: Single LED

3 3

Back Plane Board Description

GC-BS26E-RH Back plane board Components Description Condt’

No Code Description

19 J15 Hardware Address setting




23 J7 LED controller configuration jumper




4

1

2 5

7

6

8

9

101112131415

16

18 17

20 19 21 22

2324

25

26

3

3 4


System Block Diagram

VRD 11.1VRD 11.1

CPU2

Nehalem-EP

Processor

LGA1366

Port 1

CPU1

Nehalem-EP

Processor

LGA1366

Port 1Q

PI QPI

INTEL ICH10R

CLI

NK

ESI

DD

R3

DD

R3

DD

R3

DD

R3

DD

R3

DD

R3

DD

R3

DD

R3

DD

R3

DD

R3

DD

R3

DD

R3

SPD2

QPI

INTEL

Tylersburg-36D

IOH

Kawela

PCIE

x4RMI

PILOT II

LPCUSB x 1 *2 (USB0/1)

PCIE x1

ID

Switch

SwitchFP_VGA Connect

LAN port x2

COM_C

Rear VGA

BCM5221

KVM

LAN

RM

IIITE8720

TPM

Connector

PS/2USBX1 *4

USB (Type A)USBX1 *1

USBX1 (Support SSD)USBX1 *1

USBX1 *2Front USB1

Front USB2USBX1 *2

SLOT3 (x8+x8)

USB port

x 4

SATA0 SATA1 SATA2 SATA3 SATA4 SATA5

SATAII

SLOT2 (x8)

PCIEX8_RR

SLOT1 (x4+x8)

PCIEX8_RU

PCIEX8_RD

PCIE x8 GEN2

PCIE x8 GEN2

PCIE x8 GEN2

PCIE x4 GEN1

SPD1

3 5


GS-R22T61-RH Cable Routing

No Suggest Cable

1 D-Sub cable

2 SAS to SATA * cable (B/P to onboard

SATA) with SGPIO

3 Power cable for CPU

4 Fan Kit cables

No Suggest Cable

5 VGA cable

6 Front I/O + USB cables

7 SMBus cable

8 Power cable

9 Case open instrusion cable

1

2

2

3

34 4

4

4

44

4

5

5

6

6

67

78

9

9

3 6


GS-R22T81-RH Cable Routing

No Suggest Cable

1 D-Sub cable

2 SAS to SATA * cable (B/P to onboard

SATA) with SGPIO

3 Power cable for CPU

4 Fan Kit cables

No Suggest Cable

5 VGA cable

6 Front I/O + USB cables

7 SMBus cable

8 Power cable

9 Case open instrusion cable

1

5

5

4 4 4

4 4 4

6

2

22

3

36

6

7

8

9

9

3 7

Connector Icon Description

Connector Icon Description

Suggest Icon Description

Keyboard

VGA

Mouse

LAN

COM

USB

3 8


Motherboard Placement and Jumper SettingGA-7TTSH-RH Motherboard Component

SATA0 SATA2

SATA3SATA1

SATA4

SATA5

27

26

2830 2935 3133 3432

2

1

48 49

508

15

20

36

4

3

5

6 7

9

10

11

12

17

13

18

19

14

23

22

2425

21

37

39

38

40

41

42

44

43

46

45

47

16

3 9


No. Code Description

1. CPU1 Processor 1 socket2. CPU2 Processor 2 socket3. U82 Intel Tylersburg-36D IOH4. U60 Intel ICH10R5. U27 ITE IT8720F6. U5 ServerEngines PilotII7. U6 Intel 82576EB GbE8. U23 Broadcom BCM5221PHY9. U190 Winbond W83792G10. U8 BIOS Flash ROM11. F_USB1 Front USB cable connector12. F_USB2 Front USB cable connector13. USB_A1 USB Type A connector14. SSD_USB1 USB SSD Type connector15. SGPIO_JP1 SGPIO connector for BP board 116. SGPIO_JP2 SGPIO connector for BP board 217. PSMI1 PSMI connector18. IPMB1 IPMB1 connector19. IPMB2 IPMB2 connector20. COMB Serial port connector21. SATA0-5 SATA data cable cable connectors*22. CPU1_FAN CPU1 fan cable connector23. CPU2_FAN CPU2 fan cable connector24. PCI-EX8_RR Low-profile PCI-E riser slot25. PCI-EX8_RU/PCI-EX8_RD Full-height PCI-E riser slot26. DIMMA1-A2 DDR3 sockets for processor 1

DIMMB1-B2DIMMC1-C2

27. DIMMD1-D2 DDR3 sockets for processor 2DIMME1-E2DIMMF1-F2

4 0

Motherboard ComponontsNo. Code Description

28. KB_MS1 Keyboard/Mouse ports29. GLAN1 Gigabit LAN ports30. COMA_VGA Serial/VGA ports31. RLAN_L1 i-KVM LAN Port32. R_USB1 USB 2.0 port33. R_USB2 USB 2.0 port34. R_USB3 USB 2.0 port35. R_USB4 USB 2.0 port36. SW1 ID Switch37. ATX_12V1 24-pin Power connector38. SSI_2X4P1 8-pin Power connector39. SSI_2X4P2 8-pin Power connector40. TPM_20 TPM connector41. F_PANEL1 Front panel connector42. BAT CMOS Battery43. CLR_CMOS Clear CMOS jumper44. BIOS_RVCR BIOS Recovery jumper45. CLR_RTC Clear RTC jumper46. PASS_DIS Skip Supervisor password jumper47. BMC_SEL BMC Selection jumper48. JP_STRP8 PilotII firmware upgrade jumper49. JP_STRP2 PilotII firmware upgrade jumper50. PILOT_DIS PilotII Force Mode jumper

4 1


Motherboard Jumper Setting 43 ) CLR_CMOS (Clear CMOS jumper)You may clear the CMOS data to its default values by this jumper.Default value doesn’t include the “Shunter” to prevent from improper use this jumper. Toclear CMOS, temporarily short 2-3 pin.

1-2 close: Normal operation (Default setting)

2-3 close: Clear CMOS

1

1

44 ) BIOS_REV (BIOS Revocery jumper)

1

1

1-2 close: Normal operation. (Default setting)

2-3 close: Enable BIOS Recovery function.

46 ) PASS_DIS (Skip Supervisor password jumper)

1

1

1-2 Close: Normal operation. (Default setting)

2-3 Close: Clear Supervisor Password in BIOS setup menu.

47 ) BMC_SEL (BMC Selection jumper)

1-2 Close: Normal operation. (Default setting)1

1 2-3 Close: Enable BMC function.

45 ) CLR_RTC (Clear RTC jumper)

1

1 2-3 close: Clear RTC status

1-2 close: Normal operation. (Default setting)

4 2

Jumper Setting

48/49 ) JP_STRAP2/ JP_STRAP8 (PilotII firmware upgrade jumper)

JP_STRAP2 JP_STRAP8 Descripeion

Boot from BMC BOOT SPI Interface. (Default setting)

Boot From BMC LPC BOOT ROM interface.

Boot From internal ROM(Scratchpad Registers)

Boot From internal ROM(Scratchpad Registers)

1

1

1

1

1

1

1

1

1-2 close: Normal operation (Default setting)

2-3 close: Disable PilotII device function.

1

1

50 ) PILOT_DIS (PilotII Force Mode jumper)

4 3


Expansion Card Components DescriptionThe two riser cards installed in the PCI riser card bracket assembly povides support for both full-

heoght and low-profile expansion cards.

Full height and low profile PCI Express riser cards

SLOT_3

SLOT_2

SLOT_1

SLOT_5

SLOT_4

4 4



1 PCI_3 PCI express 2.0 x8 slot

(PCI Express 2.0 x8 throughtput)









4 5


Full-height riser PCI-X riser card (Optional)

SLOT_3

SLOT_2

SLOT_1


1 PCI_3 PCI- X slot





4 6

BIOS Setup

<> Move to previous item

<> Move to next item

<> Move to the item in the left hand

<> Move to the item in the right hand

<Esc> Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and

Option Page Setup Menu - Exit current page and return to Main Menu

<+/PgUp> Increase the numeric value or make changes

<-/PgDn> Decrease the numeric value or make changes

<F1> General help, only for Status Page Setup Menu and Option Page Setup Menu

<F2> Reserved

<F3> Reserved

<F4> Reserved

<F6> Reserved

<F7> Reserved

<F8> Reserved

<F9> Load the Optimized Defaults

<F10> Save all the CMOS changes, only for Main Menu

BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user toconfigure required settings or to activate certain system features.The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.When the power is turned off, the battery on the motherboard supplies the necessary power to theCMOS SRAM.

ENTERING SETUPWhen the power is turned on, press the <F2> button during the BIOS POST (Power-On Self Test)will take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing"Ctrl + F1".

CONTROL KEYS

BIOS Setup

4 7


GETTING HELP

Main Menu

The on-line description of the highlighted setup function is displayed at the bottom of the screen.

Status Page Setup Menu / Option Page Setup Menu

Press F1 to pop up a small help window that describes the appropriate keys to use and the

possible selections for the highlighted item. To exit the Help Window press <Esc>.

Select the Load Setup Defaults item in the BIOS Exit Setup menu when somehow

the system is not stable as usual. This action makes the system reset to the default

settings for stability.

Main

This setup page includes all the items in standard compatible BIOS.

Advanced

This setup page includes all the items of Phoenix BIOS special enhanced features.

(ex: Auto detect fan and temperature status, automatically configure hard disk parameters.)

Power

This setup page includes all the items of Green function features.

Security

Change, set, or disable password. It allows you to limit access the system and setup.

Server

Server additional features enabled/disabled setup menus.

Boot

This setup page include all the items of first boot function features.

Exit

There are five optionsin this selection: Exit Saving Changes, Exit Discarding Changes, Load

Optimal Defaults, Load Failsafe Defaults, and Discard Changes.

4 8

BIOS Setup

System Date Set the System Date. Note that the “Day” automatically changed after you set the date.

System Time

The time is calculated based on the 24-hour military time clock. Set the System Time

(HH:MM:SS)

BIOS Version/BIOS Date

This category includes the information of current BIOS version and BIOS released date.

CPU Type/CPU Speed/ CPU Count

This category includes the information of CPU type, Speed ,and number of CPU count.

MainOnce you enter Phoenix BIOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. Use

arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

Figure 1: Main

4 9


Total MemorySize

The BIOS determines total memory is present during the POST.

5 0

BIOS Setup

Figure 2: Advanced

AdvancedAbout This Section: Advanced

With this section, allowing user to configure your system for advanced operation. User can

set the Processor configuration, Memory configuration, Advanced chipset configuration, PCI

configuration , SATA configuration, I/O device configuration, Boot configuration, and Thermal and

acoustic configuration.

5 1


Processor Configuration

5 2

BIOS Setup

Figure 2-1: Processor Configuration

Processor Configuration

This category includes the information of CPU Speed, Processor ID ,Processor L2 / L3

Cache, and QPI Frequency. And setup sub-menu for CPU Power Management.

Please note that setup menu options will be variable depends on the type of CPU.

Multiprocessor Specification

This option allows user to configure the multiprocessor(MP) specification revision level.

Some operating system will require 1.1 for compatibility reasons.

1.4 Support MPS Version 1.4 . (Default setting)

1.1 Support M PS Version 1.1.

Intel (R) Virtualization Technology

Intel(R) Virtualization Technology will allow a platform to run multiple operating systems and

applications in independent partitions. With virtualization, one computer system can function as

multiple “virtual” systems. With processor and I/O enhancements to Intel’s various platforms,

Intel Virtualization Technology can improve the performance and robustness of today’s software-

only virtual machine solutions.

5 3


Enabled Enable Intel Virtualization Technology. (Default setting)

Disabled Disable this function.

Execute Disable Bit

Enabled Enable Execute Disable Bit. (Default setting)


Hardware Prefetcher

The Hardware Prefetcher looks the streams of data. The data is prefetched into L2 from external

memory. Disabling of this item may impact processor performance.

Enabled Enabled Hardware Prefetcher. (Default setting)

Disabled Disables this function. IP Prefetcher

Adjacent Cache Line Prefetch

When enable this item, both cache lines that comprise a cache line pair when it determines data

required is not currently in its cache.

Enabled Adjacent Cache Line Prefetch. (Default setting)

Disabled Disables this function.

CPU Thermal Trip

Enabled Enable CPU Thermal Trip. (Default setting)

Disabled Disable CPU Thermal Trip.

BMC Action for CPU Thermal Trip

Options No Action, Power Off, Power Cycle. Default setting is Power off.

Processor Retest

Enabled Enable Processor Retest.

Disabled Disable Processor Retest. (Default setting)

NUMA Aware

Enabled Enable NUMA Aware. (Default setting)

Disabled Disable NUMA Aware.

ACPI SRAT Report

Enabled Enable ACPI SRAT Report. (Default setting)

Disabled Disable ACPI SRAT Report.

5 4

BIOS Setup

Active Processor Cores

Options One Core, Two cores, Max Cores. Default setting is Max Cores.

Hyper-Threading Technology

Enabled Enable Intel Hyper Threading Technology. (Default setting)

Disabled Disable Intel Hyper Threading Technology.

A20M Support

Enabled Enable A20M Support. (Default setting)

Disabled Disable A20M Support.

Machine Checking

Enabled Enable Machine Checking. (Default setting)

Disabled Disable Machine Checking.

Fast String Operations

Enabled Enable Fast String Operations. (Default setting)

Disabled Disable Fast String Operations.

Set Max Ext CPUID=3

Enabled Enable Set Max Ext CPUID=3.

Disabled Disable Set Max Ext CPUID=3. (Default setting)

Echo TPR

Enabled Enable Echo TPR.

Disabled Disable Echo TPR.(Default setting)

Discrete MTRR Allocation

Enabled Enable Discrete MTRR Allocation.

Disabled Disable Discrete MTRR Allocation. (Default setting)

Thermal Management

Enabled Enable Thermal Management. (Default setting)

Disabled Disable Thermal Management.

5 5


Processor Power Management

Figure 2-1-1: Processor Power Management

EIST (GV3) & C State

Enabled Enable EIST (GV3) and C State items. (Default setting)

Disabled Disable EIST (GV3) and C State items.

EIST (GV3)

Enabled Enable EIST (GV3. (Default setting)

Disabled Disable EIST (GV3).

EIST PSD Function

HW_ALL In HW_ALL mode, the rpocessor hardware is responsible for coordinating

the P-state among logical processors dependencies. The OS is responsible

for keeping the P-state request up to date on all logical processors.

(Default setting)

5 6

BIOS Setup

SW_ALL In SW_ALL mode, the OS Power Manager is responsible for coordinating

the P-state among loical processors with dependencies and must initiate the

transition on all of those Logical Processors.

SW_ANY In SW_ANY mode, the OS Power Manager is responsible for corrdinating

the P-state among logical processors with dependencies and may initiate

the transition on any of those Logical Processors .

Turbo Mode

Turbo Mode automatically allows processor cores to run faster than marked frequency if the

physical processor is operating below power, temperature and current specification limits.

Turbo Mode can be engaged with SMT (Simultanceous Multi Threading) enabled and 1 to 4 cores

active and is not limited to only a single core or logical processor.

Enabled Turbo Mode. (Default setting)

Disabled Disable Turbo Mode.

T State

Enabled Enable CPU T-State. (Default setting)

Disabled Disable T-State.

CPU C State

Enabled Enable ACPI C-State (C0, C1/C1E, C3, C6 and C7). (Default setting)

Disabled Disable C-State.

CPU C1E

Enabled Enable CPU C1E. (Default setting)

Disabled Disable CPU C1E.

OS ACPI C3 Report

C3 Desire state for the Nehalem core C3 state include in the CST as ACPI C3

state. (Default setting)

C2 Desire state for the Nehalem core C2 state include in the CST as ACPI C2

state.

Disabled Disable OS ACPI C3 Report.

CPU C6 Report

Enabled Desire state for the Nehalem core C6 state include in the CST as ACPI C3

5 7



Disabled Disable CPU C6 Report.

CPU C7 Report

Enabled Desire state for the Nehalem core C7 state include in the CST as ACPI C3


Disabled Disable CPU C7 Report.

Package C State Limit

Desired state for the C-State package limit.

Options C0, C1 State, C3 State, C6 State, C7 State, No Limit. The default setting

is C3 State.

ACPI MWAIT extensions

Enabled CST using MWAIT extension isenabled for OSPM use. (Default setting)

Disabled Disable ACPI MWAIT extensions.

5 8

BIOS Setup

Memory Configuration

5 9


System Memory/Extended Memory/Memory Frequency/DIMM Status

These category is display-only which is determined by POST (Power On Self Test) of the

BIOS.

Memory Reset

Yes Select ‘Yes’, system will clear the memory error status. Save the

changes and restart system. After rebooting system, the Memory

Reset item will set to ‘No’ automatically.

No No chnages. (Default setting)

Memory Control Settings

Manual Select ‘Manual” will pops up sub-menu for configuration.

Auto Auto configuration. (Default setting)

Memory RAS Mode

Identify the Memory RAS mode.

Memory Frequency

Select the desire value of Memory frequency. Options available: Auto, DDR-3 800,

DDR-3 1066, and DDR-3 1333.

Change Interleave setting

Change the interleave setting. Options available: 1-way, 2-way, 3-way, 4-way, and 6-way.

Rank Interleave setting

Configure interleave setting. Options available: 1-way, 2-way, and 4-way.

6 0

BIOS Setup

Advanced Chipset Configuration

6 1


Figure 2-3-1: Intel VT for Directed I/O (VT-d)

6 2

BIOS Setup

Intel VT for Directed I/O (VT-d)

Interrupt Remapping

Enabled Enable Interrupt Remapping. (Default setting)

Disabled Disable Interrupt Remapping.

Coherency Support

Enabled Enable Coherency Support.

Disabled Disable Coherency Support. (Default setting)

ATS

Enabled Enable ATS. (Default setting)

Disabled Disable ATS.

PassThrough DMA

Enabled Enable PassThrough DMA. (Default setting)

Disabled Disable PassThrough DMA.

VT-d for Port1~Port 10

Enabled Enable VT-d support for Port 1~Port 10 ports through ATSR structures in

ACPI Tables. (Default setting)

Disabled Disable VT-d for Port1~Port 10.

Advanced Chipset Control Main Menu Options

Course Grain Clocking Gating

Enabled Enable Course Grain Clocking Gating.

Disabled Disable Course Grain Clocking Gating. (Default setting)

Intel (R) I/OAT

Enabled Enable configuration mapped accesses to the I/OAT configuration sapce.

(Default setting)

Disabled Disable I/OAT.

4GB PCI HoleGranularity

Select the granularity of PCI hole for PCI resource. If MTRRS are not enough, we may use

this option to reduce the MTRR occupation.

512MB Select 512MB as granularity of PCI hole.

1GB Select 1GB as granularity of PCI hole. (Default setting)

2GB Select 2GB as granularity of PCI hole.

6 3


QPI Control Settings

Enabled Enable QPI Control settings. (Default setting)

Disabled QPI Control settings.

QPI Link Fast Mode

Enabled Enable QPI Link Fast Mode. (Default setting)

Disabled Disable QPI Link Fast Mode.

QPI Frequency Selection

Identify the desire value of QPI frequency. Option available: Auto, 4.800GT, 5.866GT.

Default setting is Auto.

QPI Isoch Support

Enabled Enable QPI Isoch Support.

Disabled Disable QPI Isoch Support. (Default setting)

QPI DCA Support

Enabled Enable QPI DCA Support. (Default setting)

Disabled Disable QPI DCA Support.

QPI scramble selection

Enabled Enable QPI scramble selection.

Disabled Disable QPI scramble selection. (Default setting)

QPI Error Report

Enabled Enable QPI Error Report.

Disabled Disable QPI Error Report. (Default setting)

Memory ECC Error Log

Identify the the memory ecc error log. Option available: Disable, Correctable Error,

Uncorrectable Error, and Both. The default setting is Both.

ECC Threshold

Use the “+” and “-” keys to adjust the desire value of ECC Threshold.

Unconrrectable Pass to OS

Enabled Enable Unconrrectable Pass to OS. (Default setting)

Disabled Disable Unconrrectable Pass to OS.

Enable Multimedia Timer

Yes Enable Multimedia Timer support. (Default setting)

No Disable this function.

6 4

BIOS Setup

PCI Configuration

Figure 2-4: PCI Configuration

PCI Slot 1/2/3/4/5 Option ROM

Enabled Enable this item to initialize device expansion ROM.

(Defualt setting)


Onboard VGA Controller

Enabled Enable Onboard VGA device. (Defualt setting)


Onboard LAN iSCSI Boot ROM

Enabled Enable Onboard LAN iSCSI Boot ROM.

Disabled Disable this function. (Defualt setting)

Onboard LAN1 Controller

Enabled Enable Onboard LAN controller. (Defualt setting)


6 5


LAN1Option ROM

Enabled Enable onboard LAN1 device and initialize device expansionROM. (Default setting)


Onboard LAN2 Controller

Enabled Enable Onboard LAN controller. (Defualt setting)


LAN2Option ROM

Enabled Enable onboard LAN2 device and initialize device expansionROM. (Default setting)


Legacy USB Support

This option allows user to function support for legacy USB.

Enabled Enables support for legacy USB (Default setting)

Disabled Disables support for legacy USB.

6 6

BIOS Setup

SATA Configuration

Figure 2-5: SATA Configuration

6 7


Serial ATA

Enabled Enables on-board serial ATA function. (Default setting)

Disabled Disables on-board serial ATA function.

Native Mode Operation

This option allows user to set the native mode for Serial ATA function.

Auto Auto detected. (Default setting)

Serial ATA Set Native mode to Serial ATA.

SATA Controller Mode Option

Compatible Mode SATA and PATA drives are auto-detected and placed inLegacy mode.

Enhanced Mode SATA and PATA drives are auto-detected and placed in

Native mode. (Default setting)

Note: Pre-Win2000 operating system do not work in Enhanced mode.

SATA RAID Enable

Enabled Enabled SATA RAID function.

Disabled Disable this function. (Default setting)

SATA AHCI Enable

Enabled Set this item to enable SATA AHCI function for WinXP-SP1+IAA

driver supports AHCI mode.

Disabled Disabled this function. (Default setting)

SATA Port 0/1/2/3/4/5

The category identifies the types of Serial SATA hard disk from drive 0 to 5 that has been

installed in the computer. System will automatically detect HDD type.

Note that the specifications of your drive must match with the drive table. The hard disk will not

work properly if you enter improper information for this category.

Hard drive information should be labled on the outside device casing. Enter the appropriate option

based on this information.

TYPE

1-39: Predefined types.

Users: Set parameters by User.

6 8

BIOS Setup

Auto: Set parameters automatically. (Default setting)

CD-ROM: Use for ATAPI CD-ROM drives or double click [Auto] to set all HDD parameters

automatically.

ATAPI Removable: Removable disk drive is installed here.

Multi-Sector Transfer

This field displays the information of Multi-Sector Transfer Mode.

Disabled: The data transfer from and to the device occurs one sector at a time.

Auto: The data transfer from and to the device occurs multiple sectors at a time if the device

supports it.

LBA Mode Control This field shows if the device type in the specific IDE channel

support LBA Mode.

32-Bit I/O Enable this function to max imize the IDE data transfer rate.

Transfer Mode This field shows the information of Teansfer Mode.

Ultra DMA Mode This filed displays the DMA mode of the device in the specific IDE

channel.

6 9


I/O DeviceConfiguration

Serial Port A

This allows users to configure serial prot A by using this option.

Enabled Enable the configuration. (Default setting)

Disabled Disable the configuration.

Base I/O Address/IRQ

3F8/IRQ4 Set IO address to 3F8/IRQ4.(Default setting)

2F8/IRQ3 Set IO address to 2F8/IRQ3.

3E8/IRQ7 Set IO address to 3E8/IRQ7.


Serial Port B

This allows users to configure serial prot B by using this option.

Enabled Enable the configuration (Default setting)

Disabled Disable the configuration.

Figure 2-6: I/O Device Configuration

7 0

BIOS Setup

Base I/O Address/IRQ

3F8/IRQ4 Set IO address to 3F8/IRQ4.

2F8/IRQ3 Set IO address to 2F8/IRQ3. (Default setting)



PS/2 Mouse

Set this option ‘Enabled’ to allow BIOS support for a PS/2 - type mouse.

Enabled ‘Enabled’ forces the PS/2 mouse port to be enabled regardless if amouse is present. (Default setting)

Disabled ‘Disabled’ prevents any installed PS/2 mouse from functioning,but frees up IRQ12.

7 1


Boot Configuration

Boot -time Diagnostic Screen

When this item is enabled, system will shows Diagnostic status when system boot.

Enabled Enable Boot-time Diagnostic.


Post Error Pause

The category determines whether the computer will stop if an error is detected during power up.

All Error Whenever the BIOS detects a non-fatal error the system will be

stopped.

No Error The system boot will not stop for any error that may be detected

and you will be prompted.

All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all

other errors. (Default setting)

Figure 2-7: Boot Configuration

7 2

BIOS Setup

NumLock

This option allows user to select power-on state for NumLock.

On Enable NumLock. (Default setting)

Off Disable this function.

7 3


Thermal and Acoustic Configuration

Figure 2-8: Thermal and Acoustic Configuration

Open loop Thermal Throttle

Enabled Open loop Thermal Throttle. (Default setting)

Disabled Disable Open loop Thermal Throttle.

Temperature Chassis inlet

This item is user defined. Use nuber key to adjust desired value.

Temperature Rise


Air speed to the DIMMs


System Altitude


Pitch between DIMMs


7 4

BIOS Setup

Close loop Thermal Throttle

Enabled Close loop Thermal Throttle. (Default setting)

Disabled Disable Close loop Thermal Throttle.

Temperature hysteresis


Temperature guardband


Temperature Chassis inlet


Temperature Rise


Air speed to the DIMMs


System Altitude


Pitch between DIMMs


7 5


Power

Figure 3: Power

Power on by RTC Alarm

You can set item to Enabled and key in Date/Time to power on system.

On Enable alarm function to POWER ON system.

Off Disable this function. (Default setting)

If Resume On Time is Enabled.

Resume Date Everyday, 1~31

Resume Time (0~23) : (0~59) : (0~59)

Power On PCI & PCIE Devices

Enabled Enable Power On PCIe Devices. (Default setting)


Power On by Modem Ring

Enabled Enable Power On by Modem Ring. (Default setting)

Disabled DisablePower On by Modem Ring.

7 6

BIOS Setup

Wake Up by PS/2 KB/Mouse

Enabled Enable Wake Up by PS/2 KB/Mouse. (Default setting)

Disabled Disable Wake Up by PS/2 KB/Mouse function.

Wake Up by USB KB/Mouse

Enabled Enable Wake Up by USB KB/Mouse. (Default setting)

Disabled Disable Wake Up by USB KB/Mouse function.

After Power Failure

This option provides user to set the mode of operation if an AC / power loss occurs.

Power On System power state when AC cord is re-plugged.

Stay Off Do not power on system when AC power is back.

Last State Set system to the last sate when AC power is removed. Do not power onsystem when AC power is back. (Default setting)

7 7


Security

Figure 4: Security

Set Supervisor Password

You can install and change this options for the setup menus. Type the password up to 6

characters in lengh and press <Enter>. The password typed now will clear any previously

entered password from the CMOS memory. You will be asked to confirm the entered

password. Type the password again and press <Enter>. You may also press <Esc> to abort

the selection and not enter a specified password or press <Enter> key to disable this option.

About This Section: Security

In this section, user can set either supervisor or user passwords, or both for different level of

password securities. In addition, user also can set the virus protection for boot sector.

7 8

BIOS Setup

Set User Password

You can only enter but do not have the right to change the options of the setup menus. When

you select this function, the following message will appear at the center of the screen to assist

you in creating a password.

Type the password up to 6 characters in lengh and press <Enter>. The password typed now

will clear any previously entered password from the CMOS memory. You will be asked to

confirm the entered password. Type the password again and press <Enter>. You may also

press <Esc> to abort the selection and not enter a specified password.

Password on boot

Password entering will be required when system on boot.

Enabled Requries entering password when system on boot.


Security Mode for PWR/RST Button

Enabled Enable Security Mode for PWR/RST Button.


Clear Case Open Status

Press [Enter] to clear the case open status.

TPM Support

TPM, stands for Trusted Platform Module. A Trusted Platform Module provides function for

secure generation of cryptographic keys, the ability to limit the use of cryptographic keys, as

well as a hardware pseudo-random number generator.

Enabled Enable TPM Support.


Current TPM State

Displays the current TPM State status.

Change TPM State

No Change No configuration on TPM State. (Default setting)

Enable & Activate Enable and activate TPM State.

Deactivate & Disable Disable and deactivate TPM State.

Clear Clear the TPM stored information on the TPM.

7 9


Server

Figure 5: Server

8 0


System Management

Figure 5-1: System Management

8 1


System Management

This category allows user to view the system management features. Including information of

Motherboard Hardware information and software information.

BMC IP Address Source

Address obtained by BMC running DHCP or Static address.

Option available: DHCP, Static.

8 2

BIOS Setup

Figure 5-2: Console Redirection

Console Redirection

Console Redirection

If this option is set to enabled, it will use a port on the motherboard to run console redirection

function.

On-board COM A Use Serial Port A as the COM port address.

On-board COM B Use Serial Port B as the COM port address.


Flow ControlThis option provide user to enable the flow control function.

None Not supported.

XON/XOFF Software control.

CTS/RTS Hardware control. (Default setting)

Baud Rate

8 3


This option allows user to set the specified baud rate.

Options 300, 1200, 2400, 9600, 19.2K, 38.4K, 57.6K, 115.2K.

Terminal Type

This option allows user to select the specified terminal type. This is defined by IEEE.

Options VT100, VT100 8bit, PC-ANSI 7bit, PC-ANSI, VT100+, VT-UTF8,ASCII.

Continue C.R. after POST

This option allows user to enable console redirection after O.S has loaded.

On Enable console redirection after O.S has loaded.

Off Disable this function. (Default setting)

8 4


Event Log Configuration

Figure 5-3: Event Log Configuration

Assert NMI on SERR

Enabled Enable Assert NMI on SERR function. (Default setting)


Assert NMI on PERR

Enabled Enable Assert NMI on PERR function. (Default setting)


Clear all Event Logs

Press [Enter] to clear all event logs.

Log POST System Event

Enabled Enable Log POST System Event. (Default setting)


8 5

BIOS Setup

Boot

Figure 6: Boot

Boot Priority Order

This field determines which type of device the system attempt to boot from after

PhoenixBIOS Post completed. Specifies the boot sequence from the available devices. If

the first device is not a bootable device, the system will seek for next available device.

Key used to view or configure devices:

Up and Down arrows select a device.

<+> and <-> moves the device up or down.

<f> and <r> specifies the device fixed or removable.

<x> exclude or include the device to boot.

<Shift + 1> Enable or disable a device.

<1-4> Loads default boot secquence.

8 6


Exit

Figure 7: Exit

About This Section: ExitOnce you have changed all of the set values in the BIOS setup, you should save your

changes and exit BIOS setup program. Select “Exit” from the menu bar, to display the

following sub-menu.

Exit Saving Changes

Exit Discarding Changes

Load Settup Default

Discard Changes

Save Changes

8 7

BIOS Setup

Exit Saving Changes

This option allows user to exit system setup with saving the changes.

Press <Enter> on this item to ask for the following confirmation message:

Pressing ‘Y’ to store all the present setting values tha user made in this time into CMOS.

Therefore, whenyou boot up your computer next time, the BIOS will

re-configure your system according data in CMOS.

8 8


Exit Discarding ChangesThis option allows user to exit system setup without changing anyprevious settings values in

CMOS. The previous selection remain in effect.

This will exit the Setup Utility and restart your compuetr when selecting this option.

8 9

BIOS Setup

Load Settup Default

This option allows user to load default values for all setup items.

When you press <Enter> on this item, you will get a confirmation dialog box with a message

as below:

9 0


Discard ChangesThis option allows user to load previos values from CMOS for all setup item.


as below:

9 1

BIOS Setup

Save Changes

This option allows user to save setup dat ato CMOS.


as below:

Press [Yes] to save setup data to CMOS.

Appexdix

9 2

Code Beeps POST Routine Description02h Verify Real Mode03h Disable Non-Maskable Interrupt (NMI)04h Get CPU type06h Initialize system hardware08h Initialize chipset with initial POST values09h Set IN POST flag0Ah Initialize CPU registers0Bh Enable CPU cache0Ch Initialize caches to initial POST values0Eh Initialize I/O component0Fh Initialize the local bus IDE10h Initialize Power Management11h Load alternate registers with initial POST values12h Restore CPU control word during warm boot13h Initialize PCI Bus Mastering devices14h Initialize keyboard controller16h 1-2-2-3 BIOS ROM checksum17h Initialize cache before memory autosize18h 8254 timer initialization1Ah 8237 DMA controller initialization1Ch Reset Programmable Interrupt Controller20h 1-3-1-1 Test DRAM refresh22h 1-3-1-3 Test 8742 Keyboard Controller24h Set ES segment register to 4 GB26h Enable A20 line28h Autosize DRAM29h Initialize POST Memory Manager2Ah Clear 512 KB base RAM2Ch 1-3-4-1 RAM failure on address line xxxx*2Eh 1-3-4-3 RAM failure on data bits xxxx* of low byte of memory bus2Fh Enable cache before system BIOS shadow30h 1-4-1-1 RAM failure on data bits xxxx* of high byte of memory bus32h Test CPU bus-clock frequency33h Initialize Phoenix Dispatch Manager36h Warm start shut down38h Shadow system BIOS ROM3Ah Autosize cache3Ch Advanced configuration of chipset registers

Appexdix A Phoenix BIOS Beep Codes

9 3


Code Beeps POST Routine Description3Dh Load alternate registers with CMOS values42h Initialize interrupt vectors45h POST device initialization46h 2-1-2-3 Check ROM copyright notice48h Check video configuration against CMOS49h Initialize PCI bus and devices4Ah Initialize all video adapters in system4Bh QuietBoot start (optional)4Ch Shadow video BIOS ROM4Eh Display BIOS copyright notice50h Display CPU type and speed51h Initialize EISA board52h Test keyboard54h Set key click if enabled58h 2-2-3-1 Test for unexpected interrupts59h Initialize POST display service5Ah Display prompt "Press F2 to enter SETUP"5Bh Disable CPU cache5Ch Test RAM between 512 and 640 KB60h Test extended memory62h Test extended memory address lines64h Jump to UserPatch166h Configure advanced cache registers67h Initialize Multi Processor APIC68h Enable external and CPU caches69h Setup System Management Mode (SMM) area6Ah Display external L2 cache size6Bh Load custom defaults (optional)6Ch Display shadow-area message6Eh Display possible high address for UMB recovery70h Display error messages72h Check for configuration errors76h Check for keyboard errors7Ch Set up hardware interrupt vectors7Eh Initialize coprocessor if present80h Disable onboard Super I/O ports and IRQs81h Late POST device initialization82h Detect and install external RS232 ports83h Configure non-MCD IDE controllers84h Detect and install external parallel ports

Appexdix

9 4

Code Beeps POST Routine Description85h Initialize PC-compatible PnP ISA devices86h Re-initialize onboard I/O ports.87h Configure Motheboard Configurable Devices (optional)88h Initialize BIOS Data Area89h Enable Non-Maskable Interrupts (NMIs)8Ah Initialize Extended BIOS Data Area8Bh Test and initialize PS/2 mouse8Ch Initialize floppy controller8Fh Determine number of ATA drives (optional)90h Initialize hard-disk controllers91h Initialize local-bus hard-disk controllers92h Jump to UserPatch293h Build MPTABLE for multi-processor boards95h Install CD ROM for boot96h Clear huge ES segment register97h Fixup Multi Processor table98h 1-2 Search for option ROMs. One long, two short beeps on checksum failure99h Check for SMART Drive (optional)9Ah Shadow option ROMs9Ch Set up Power Management9Dh Initialize security engine (optional)9Eh Enable hardware interrupts9Fh Determine number of ATA and SCSI drivesA0h Set time of dayA2h Check key lockA4h Initialize Typematic rateA8h Erase F2 promptAAh Scan for F2 key strokeACh Enter SETUPAEh Clear Boot flagB0h Check for errorsB2h POST done - prepare to boot operating systemB4h 1 One short beep before bootB5h Terminate QuietBoot (optional)B6h Check password (optional)B9h Prepare BootBAh Initialize DMI parametersBBh Initialize PnP Option ROMsBCh Clear parity checkersBDh Display MultiBoot menuBEh Clear screen (optional)

9 5


Code Beeps POST Routine DescriptionBFh Check virus and backup remindersC0h Try to boot with INT 19C1h Initialize POST Error Manager (PEM)C2h Initialize error loggingC3h Initialize error display functC4h Initialize system error handlerC5h PnPnd dual CMOS (optional)C6h Initialize notebook docking (optional)C7h Initialize notebook docking lateC8h Force check (optional)C9h Extended checksum (optional)D2h Unknown interrupt

Code Beeps For Boot Block in Flash ROME0h Initialize the chipsetE1h Initialize the bridgeE2h Initialize the CPUE3h Initialize system timerE4h Initialize system I/OE5h Check force recovery bootE6h Checksum BIOS ROME7h Go to BIOSE8h Set Huge SegmentE9h Initialize Multi ProcessorEAh Initialize OEM special codeEBh Initialize PIC and DMAECh Initialize Memory typeEDh Initialize Memory sizeEEh Shadow Boot BlockEFh System memory testF0h Initialize interrupt vectorsF1h Initialize Run Time ClockF2h Initialize videoF3h Initialize System Management ModeF4h 1 Output one beep before bootF5h Boot to Mini DOSF6h Clear Huge SegmentF7h Boot to Full DOS

Appexdix

9 6

Appexdix B PhoenixBIOS POST Error Messages

ListThe following is a list of the messages that the BIOS can display. Most of them occur duringPOST. Some of them display information about a hardware device, e.g., the amount of memoryinstalled. Others may indicate a problem with a device, such as the way it has been configured.Following the list are explanations of the messages and remedies for reported problems.

*If your system displays one of the messages marked below with an asterisk (*),write down the message and contact your dealer. If your system fails after youmake changes in the Setup menus, reset the computer, enter Setup and installSetup defaults or correct the error.

0200 Failure Fixed DiskFixed disk is not working or not configured properly. Check to see if fixed disk is attachedproperly. Run Setup. Find out if the fixed-disk type is correctly identified.

0210 Stuck keyStuck key on keyboard.

0211 Keyboard errorKeyboard not working.

*0212 Keyboard Controller FailedKeyboard controller failed test. May require replacing keyboard controller.

0213 Keyboard locked - Unlock key switchUnlock the system to proceed.

0220 Monitor type does not match CMOS - Run SETUPMonitor type not correctly identified in Setup

*0230 Shadow Ram Failed at offset: nnnnShadow RAM failed at offset nnnn of the 64k block at which the error was detected.

*0231 System RAM Failed at offset: nnnnSystem RAM failed at offset nnnn of in the 64k block at which the error was detected.

*0232 Extended RAM Failed at offset: nnnnExtended memory not working or not configured properly at offset nnnn.

0250 System battery is dead - Replace and run SETUPThe CMOS clock battery indicator shows the battery is dead. Replace the battery and runSetup to reconfigure the system.

0251 System CMOS checksum bad - Default configuration usedSystem CMOS has been corrupted or modified incorrectly, perhaps by an application programthat changes data stored in CMOS. The BIOS installed Default Setup Values. If you do notwant these values, enter Setup and enter your own values. If the error persists, check thesystem battery or contact your dealer.

*0260 System timer errorThe timer test failed. Requires repair of system board.

9 7


*0270 Real time clock errorReal-Time Clock fails BIOS hardware test. May require board repair.

0271 Check date and time settingsBIOS found date or time out of range and reset the Real-Time Clock. May require setting legaldate (1991-2099).

0280 Previous boot incomplete - Default configuration usedPrevious POST did not complete successfully. POST loads default values and offers to runSetup. If the failure was caused by incorrect values and they are not corrected, the next bootwill likely fail. On systems with control of wait states, improper Setup settings can also terminate POST and cause this error on the next boot. Run Setup and verify that the waitstateconfiguration is correct. This error is cleared the next time the system is booted.

0281 Memory Size found by POST differed from CMOSMemory size found by POST differed from CMOS.

02B0 Diskette drive A error02B1 Diskette drive B error

Drive A: or B: is present but fails the BIOS POST diskette tests. Check to see that the drive isdefined with the proper diskette type in Setup and thatthe diskette drive is attached correctly.

02B2 Incorrect Drive A type - run SETUPType of floppy drive A: not correctly identified in Setup.

02B3 Incorrect Drive B type - run SETUPType of floppy drive B: not correctly identified in Setup.

02D0 System cache error - Cache disabledRAM cache failed and BIOS disabled the cache. On older boards, check the cache jumpers.You may have to replace the cache. See your dealer. A disabled cache slows systemperformance considerably.

02F0: CPU ID:CPU socket number for Multi-Processor error.

*02F4: EISA CMOS not writeableServerBIOS2 test error: Cannot write to EISA CMOS.

*02F5: DMA Test FailedServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers.

*02F6: Software NMI FailedServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt).

*02F7: Fail-Safe Timer NMI FailedServerBIOS2 test error: Fail-Safe Timer takes too long.

Device Address ConflictAddress conflict for specified device.

Allocation Error for: deviceRun ISA or EISA Configuration Utility to resolve resource conflict for the specified device.

CD ROM DriveCD ROM Drive identified.

Appexdix

9 8

Entering SETUP ...Starting Setup program

*Failing Bits: nnnnThe hex number nnnn is a map of the bits at the RAM address which failed the memory test.Each 1 (one) in the map indicates a failed bit. See errors 230, 231, or 232 above for offsetaddress of the failure in System, Extended, or Shadow memory.

Fixed Disk nFixed disk n (0-3) identified.

Invalid System Configuration DataProblem with NVRAM (CMOS) data.

I/O device IRQ conflictI/O device IRQ conflict error.

PS/2 Mouse Boot Summary Screen:PS/2 Mouse installed.

nnnn kB Extended RAM PassedWhere nnnn is the amount of RAM in kilobytes successfully tested.

nnnn Cache SRAM PassedWhere nnnn is the amount of system cache in kilobytes successfully tested.

nnnn kB Shadow RAM PassedWhere nnnn is the amount of shadow RAM in kilobytes successfully tested.

nnnn kB System RAM PassedWhere nnnn is the amount of system RAM in kilobytes successfully tested.

One or more I2O Block Storage Devices were excluded from the Setup Boot MenuThere was not enough room in the IPL table to display all installed I2O block-storage devices.

Operating system not foundOperating system cannot be located on either drive A: or drive C:. EnterSetup and see if fixed disk and drive A: are properly identified.

*Parity Check 1 nnnnParity error found in the system bus. BIOS attempts to locate the address and display it on thescreen. If it cannot locate the address, it displays ????. Parity is a method for checking errorsin binary data. A parity error indicates that some data has been corrupted.

*Parity Check 2 nnnnParity error found in the I/O bus. BIOS attempts to locate the address and display it on thescreen. If it cannot locate the address, it displays ????.

Press <F1> to resume, <F2> to Setup,<F3> for previous

Displayed after any recoverable error message. Press <F1> to start the boot process or <F2>to enter Setup and change the settings. Press <F3> to display the previous screen (usually aninitialization error of an Option ROM, i.e., an add-on card). Write down and follow theinformation shown on the screen.

9 9

GS-R22T61-RH/GS-R22T81-RH Rack Mount ServerPress <F2> to enter Setup

Optional message displayed during POST. Can be turned off in Setup.PS/2 Mouse:

PS/2 mouse identified.Run the I2O Configuration Utility

One or more unclaimed block storage devices have the Configuration Request bit set in theLCT. Run an I2O Configuration Utility (e.g. the SAC utility).

System BIOS shadowedSystem BIOS copied to shadow RAM.

UMB upper limit segment address: nnnnDisplays the address nnnn of the upper limit of Upper Memory Blocks, indicating releasedsegments of the BIOS which can be reclaimed by a virtual memory manager.Video BIOS shadowed Video BIOS successfully copied to shadow RAM.

r22t6 r22t8 1.0 q - GIGABYTE

Documents

Transcript of r22t6 r22t8 1.0 q - GIGABYTE